Dynaudio Sub 3 Owner's Manual

Dynaudio Sub 3: Power, control, and punch for your system. Experience the ultimate audio experience with this high-performance subwoofer, designed to deliver deep, accurate bass that will enhance your music, movies, and gaming. With its advanced features, including adjustable volume, cut-off frequencies, and phase control, you can customize the sound to perfectly match your system and room acoustics.

PDF

Document

Sub 3

Owner’s manual

Hello

Welcome to Dynaudio Sub 3

Power, control and punch for your system

This is

Sub 3

6 Introduction

8 Important safety instructions

10 About this manual

12 Unpacking

14 Controls and connections

16 Operation

16 Connecting the subwoofer

18 Connecting a single subwoofer

19 Multiple subwoofer connections

20 Connecting loudspeakers

21 Switching the subwoofer on/off

22 Adjusting the volume (GAIN)

23 Selecting the subwoofer cut-off frequency

(SUB Lowpass)

24 Setting the phase (Phase)

25 Setting the satellite cut-off frequency

(Highpass)

26 Positioning the subwoofer

27 Impact of room-modes

28 Positioning possibilities

29 Using multiple subwoofers

30 General tips

32 Volume (GAIN)

32 Cut-off frequencies

34 Control possibilities

35 General tips

36 Specific tips

38 Troubleshooting

40 Care and maintenance

42 Warranty

43 Technical specifications

Introduction

Introduction

Dear music lover

Welcome to your new Dynaudio subwoofer.

We’ve been designing, engineering and creating speakers at our Denmark headquarters since 1977, and ever since we started we’ve been pouring advanced

R&D technology into every model.

What comes out is audio reproduction at the highest level, making listening to even the most familiar recordings a new listening experience altogether.

Our aim: to reproduce exactly what was happening in the studio at the time of the original recording.

In fact, we’re one of very few companies who can realize such concepts. That’s thanks to Dynaudio Labs, our in-house development and production facility.

It’s so advanced, in fact, that we’ve been given TS16949 certification.

Each loudspeaker is constructed and rigorously tested by our mastercraftsmen to these incredibly demanding standards.

If you want to get the best possible performance from them (that’s why you bought Dynaudio in the first place, after all), take a look at the information on the following pages. By considering our tips and suggestions, you’ll be recreating what our engineers do in our testing rooms: extracting every ounce of detail and nuance in the music… and then enjoying every second of it.

We wish you many years of enjoyment with your new subwoofer.

Dynaudio

Important safety instructions

Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.

16. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. The mains plug of the power supply cord shall remain readily operable.

WARNING

Risk of Electric Shock. Do Not Open.

To reduce the risk of electric shock, do not remove the rear panel and do not expose the apparatus to rain or moisture.

No user serviceable parts inside. Refer servicing to qualified personnel.

About this manual

About this manual

Safety signs

In this operating manual following signs and symbols are used.

General safety sign

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Dangerous voltage

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Signal words

NOTICE

Indicates in combination with a safety sign a hazardous situation which, if not avoided, will result in damage to equipment.

CAUTION

Indicates in combination with a safety sign a potentially hazardous situation which, if not avoided, could result in minor or moderate injury or damage to equipment.

WARNING

Indicates in combination with a safety sign a potentially hazardous situation which, if not avoided, could result in death or serious injury.

DANGER

Indicates in combination with a safety sign a hazardous situation which, if not avoided, will result in death or serious injury.

How this operating manual is structured

This operating manual is divided in three main chapters, in which you can find all the information needed to operate the

Dynaudio Sub 3 successfully: about unpacking and connecting the subwoofer. The controls and connections on the rear panel are also described here.

learn how to operate the subwoofer in general and how to position it properly for optimum performance.

Troubleshooting: Here detailed

explanations can be found how to optimize the settings in order to achieve the maximum sound quality.

You will find this chapter titles on top of each page for your quick navigation.

1 2 3

Unpacking

Unpacking

To find the suitable position for the Sub

3 in your listening room, please read the chapter “Positioning the subwoofer” on page 20.

To unpack the subwoofer

1. Unpack the subwoofer on a clean, even and soft area; floor carpeting is very suitable.

2. The packaging should be opened from the top. Remove all accessories that come packed with the subwoofer. Do not remove the top part of the protective material.

3. With the protective material still in place but with accessories removed, carefully tilt the packaging on its side and tilt again to turn it upside-down.

Ensure that no part of the top-cover is obstructing the opening at the top.

4. The outer packaging can now be lifted away from the subwoofer itself.

Remove the protective material that now is on top. Through the bag you can now see the underside of the subwoofer.

5. Open the bag and remove such from around the base of the subwoofer.

6. Again, carefully tilt the subwoofer on its side and again to turn it onto its feet. Note that the top part of the protective material will now come off easily so ensure that the subwoofer does not drop or slide away in the process.

Check that the contents are complete

• Subwoofer: The factory-set power requirements (refer to label on rear of subwoofer) should correspond for the region where the subwoofer was purchased. Refer also to chapter

“Important Safety Instructions” on page 8.

• Front baffle grille

• AC mains lead. The supplied lead should be suitable for the region where the subwoofer was purchased.

• Owners manual

Grille

The subwoofer can be operated without the grille. However, it is recommended that the grille is mounted during normal use to help prevent accidental damage or dirt settling on the cone of the loudspeaker. With subwoofers, the influence of the grille on the sound is virtually negligible.

To remove the grille:

Gently pull the grille at all corners.

To fit the grille:

Line up the studs with the corresponding front baffle holes.

Gently push the grille in at all corners.

Note

Be careful when mounting the grille not to touch the cone of the loudspeaker itself.

Controls and connections

ON/OFF

Main power switch (to switch the subwoofer manually on and off).

LED: shows operation mode:

• red = subwoofer switched on and in mute mode

• green = subwoofer is activated

AC IN

Main power input.

POWER

Subwoofer auto power mode:

• ON = Auto mode disabled

(subwoofer is switched on permanently, when main power switch is set to ON).

• AUTO = Auto mode enabeld (when main power switch is set to ON and a music signal is detected, the internal amplifier is activated automatically).

GAIN

Subwoofer volume level.

PHASE

Phase setting: phase can be set to

0° or 180°.

SUB Lowpass

Subwoofer lowpass frequency: continuously variable from 50 to

150Hz.

SAT Highpass

Allows cutting off low frequencies of the signal provided at the SAT

Output:

• Flat = signal is not processed

• 60 = cut-off frequency at 60Hz

• 80 = cut-off frequency at 80Hz

SAT/SUB Input, SAT Output

• SAT/SUB Input: Input for full bandwidth signal from processor/ receiver. This signal will be processed according to the SAT

Highpass setting and provided at

the SAT Output connection for satellite speakers to be connected.

• SAT Output: Output for satellite speakers to be connected. This signal is processed according to the SAT Highpass setting.

SUB I/O, To Slave

• LFE/Slave IN: input for LFE signal from processor/receiver. Note that the signal must be a true LFE signal or already have been filtered by the processor/receiver, as SUB

Lowpass does not have an effect

in combination with the LFE input.

• OUT: output to next subwoofer if installed.

10.

LFE/Slave

Subwoofer operation mode LFE or

Slave:

• LFE: setting if just one subwoofer is used or for first subwoofer if system consists of multiple subwoofers. Note that the SUB

Lowpass control does not have

an effect when the LFE Mode is selected.

• Slave: setting for second and all following subwoofers. Note that the SUB Lowpass, PHASE and

GAIN controls do not have an

effect when the Slave Mode is selected.

10.

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

LEFT

SAT/SUB Input SAT Output

RIGHT

SUB I/O

LFE / Slave IN

LFE Slave

OUT

100-120V/220-240V

50/60Hz 3.15A

To Slave

OFF

FUSE T3.15A L 250V

Controls and connections

Operation

Connecting the subwoofer

Subwoofer inputs

The Dynaudio Sub 3 provides two different signal inputs:

SUB I/O - LFE/Slave In

This input allows the LFE (Low

Frequency Effect) channel to be connected, which is used in home cinema systems to reproduce low frequency effects.

The signal is:

• reproduced by the subwoofer

• routed to the SUB I/O - LFE/

To Slave output for a second subwoofer to be connected.

The SUB Lowpass control has no impact on this input.

SAT/SUB Input

This input allows the connection of the full bandwidth signal from the processor/ receiver (preamplifier out).

The signal is:

• reproduced by the subwoofer,

• routed to the SAT Output terminals.

Low frequencies are cut-off according to the SAT Highpass setting,

• routed to the SUB I/O - LFE/

To Slave output for a second subwoofer to be connected. High frequencies are cut-off according to the SUB Lowpass setting.

See figure above for correlations between input, output and settings.

Operation

SUB I/O

LFE/Slave In

SAT/SUB

Input

NOTICE

Damage of device due to improper connection

Set the mains power switch to OFF before connecting the Sub 3.

Only switch the subwoofer on

(mains power switch to ON) after all connections and set up steps have been properly completed.

Mode

SUB

Lowpass

SAT

Highpass

LFE

Gain

Slave

Phase

Subwoofer

SUB I/O to slave

SAT/SUB

Output

Note

All Sub 3 inputs and outputs are low level terminals. Thus, neither a power amplifier output must be connected to the subwoofer nor passive loudspeakers can be driven by the subwoofer directly!

Front Out/Pre Out 2.

LFE/SUB Out

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

SAT/SUB Input

LEFT

SAT Output

RIGHT

SUB I/O

LFE / Slave IN

LFE Slave

OUT

To Slave

Connecting a single subwoofer

To connect the SAT/SUB input:

From the preamplifier output of your processor/receiver, PC or mediaplayer (often marked as Pre

Out or Front Out) connect a stereo

RCA cable to the subwoofer SAT/

SUB Input.

This signal should not be already processed by the processor/receiver.

Please pay attention to the settings of your processor/receiver.

To connect the LFE channel:

From the processor or receiver’s low-level (not a speaker output) subwoofer output (often marked as “subwoofer out”, “Sub out” or

“LFE”), connect a mono RCA-to-

RCA cable to the subwoofer input

SUB I/O - LFE/Slave IN.

This signal should not be already processed by the processor/receiver.

Please pay attention to the settings of your processor/receiver.

Set the MODE switch to LFE.

Note

You also can use both connection types. Both signals will be combined in the Sub 3 and routed accordingly.

This allows the Sub 3 to reproduce both the LFE channel information as well as the bass range of the connected satellite speakers

Note

In order to avoid interference and noise, we recommend you use quality, well shielded cables.

When using multiple subwoofers in a Master-Slave setup, it is recommended that the subwoofers are all the same model.

If you wish to use multiple subwoofers with full individual control, set the Input switch for all to the “Master” position.

From the Amplifier, processor or receiver’s subwoofer output, use a

Y-connector.

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

Operation

PHASE

0° 180°

50Hz 150Hz

SAT/SUB Input

LEFT

SAT Output

1. Front Out/

Pre Out

LFE/SUB Out

Mode

RIGHT

SUB I/O

LFE / Slave IN

LFE Slave

SAT/SUB Input

LEFT

SAT Output

RIGHT

OUT

To Slave SUB I/O

LFE / Slave IN

LFE Slave

OUT

To Slave

Mode Sub (Slave)

Multiple subwoofer connections

The Dynaudio Sub 3 can be used stand-alone or together with multiple subwoofer units. Using multiple units may be helpful if the listening room is quite large or has difficult acoustic conditions (e.g. room-modes, see also

“Positioning the subwoofer” on page 26 for further information).

When using two or more subwoofers, the first one (designated “Master”) controls the following subs (designated “Slave”) via a subwoofer cable.

To connect multiple subwoofers:

1. Connect the first subwoofer with the processor/receiver as described before.

to LFE.

3. From the OUT - To Slave output of the first subwoofer connect a mono

RCA-to-RCA cable to the SUB I/O -

LFE/Slave IN input of the following subwoofer. This now becomes the slave.

Set the MODE switch of the second subwoofer to Slave.

Further subwoofers can be connected in the same way. Set the MODE switch of all following subwoofers to Slave respectively.

Connecting loudspeakers

In home cinema systems the bass management - meaning the distribution of the low frequencies to the subwoofer and the speakers - is handled by the settings of the processor/receiver. If your equipment does not provide bass management, or if you want to use the

Sub 3 together with a common stereo, the low frequency adjustment of the connected speakers can be managed by the Sub 3. This not only improves the sound by matching subwoofer and speakers, but also by freeing the power amplifier and connected speakers from the effects of sound-compromising bass reproduction. Also refer to the further explanations in the chapter “Connecting the subwoofer” on page 10.

To connect speakers:

Connect the subwoofer with the processor/receiver as explained in

“Connecting a single subwoofer” on page 18.

From the Subwoofer SAT Output connect a RCA cable to the Main

In of the power amplifier you use for your speakers.

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

SAT/SUB Input

LEFT

SAT Output

RIGHT

SUB I/O

LFE / Slave IN

LFE Slave

OUT

To Slave

Note

Stereos do not have a LFE channel. In this case just connect the front outputs of the processor/receiver (Front Out/Pre Out) with the subwoofer.

The signals connected to the SAT/SUB Input are provided at the OUT - To

Slave output for connecting another subwoofer. See page 19 to learn more about connecting multiple subwoofers.

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

SAT/SUB Input

LEFT

SAT Output

RIGHT

Power mode

Switch on

LFE / Slave IN

POWER

SUB I/O

ON AUTO

GAIN

Min Max

OUT

PHASE

To Slave

0° 180°

Flat 60Hz 80Hz

50Hz

50/60Hz 3.15A

SAT/SUB Input

LEFT

OFF

SAT Output

FUSE T3.15A L 250V

RIGHT

Switching the subwoofer on/off

Once you have ensured yourself that all necessary connections have been made, the subwoofer and the connected components can be switched on.

Switch the subwoofer ON with the main POWER switch on the rear panel.

The status LED on the rear of the subwoofer will light up red.

Power mode

After switching on the Sub 3 the Power mode should be selected:

LFE / Slave IN OUT

To Slave

• When a music signal is detected, the internal amplifier is activated

LFE

automatically. The status LED on the rear of the subwoofer will light up green. the subwoofer’s input, it will remain switched on.

50/60Hz 3.15A

• After 15 to 20 minutes of not sensing any input signal, the subwoofer will switch itself to mute mode subwoofer will light up red.

enabled.

Operation

Adjusting the volume (GAIN)

POWER

ON AUTO

GAIN

Min

SAT Highpass

Flat 60Hz 80Hz

SUB Lowpass

Max

PHASE

0° 180°

50Hz 150Hz

CAUTION

High Sound Levels

To avoid auditory defects do not listen to high sound levels over a longer period of time.

The correct volume setting is an important aspect in achieving a well balanced speaker combination. Please also refer to “Specific tips” on page 28 for further information or ask your local

Dynaudio dealer for assistance.

Adjust the GAIN control, until correct setting is reached.

Note

You can not adjust the volume,

SAT/SUB Input

mode. In this case the volume is controlled by the setting of the

LEFT

RIGHT

SAT Output

SUB I/O

LFE / Slave IN OUT

To Slave

LFE Slave

100-120V/220-240V

50/60Hz 3.15A

OFF

FUSE T3.15A L 250V

POWER

ON AUTO

GAIN

Min

SAT Highpass

Flat 60Hz 80Hz

SUB Lowpass

Max

PHASE

0° 180°

50Hz 150Hz

Operation

Selecting the subwoofer cut-off frequency

(SUB Lowpass)

The SUB Lowpass control allows the frequency range of the subwoofer to be defined. Above the selected frequency the sound level decreases rapidly.

The correct setting of this cut-off frequency is important for a well balanced combination of subwoofer and speakers.

To select the cut-off frequency:

Set the SUB Lowpass control to the desired frequency between 50 and 150Hz.

SAT/SUB Input SAT Output

LEFT

Note

In most audio-video-systems the subwoofer cut-off frequency is already set in the bass management of your processor/receiver. Please refer to the operating manual of your processor/receiver for further information. If possible, switch off any settings. If your processor/receiver does not allow to switch off the maximum value (turn to the very right, 150Hz).

Please also heed the instructions given in the operating manual of your loudspeakers, and refer to “Cut-off frequencies” on page 25 for further

OUT

SUB I/O To Slave

LFE Slave

100-120V/220-240V

50/60Hz 3.15A

OFF

FUSE T3.15A L 250V

Combined frequency response

Subwoofer

Main speakers

Frequency

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

50Hz 150Hz

Setting the phase

(Phase)

With the phase settings you can adjust the timing relationship between the subwoofer and main speakers. If either subwoofer or main speaker are slightly delayed in response in relation to the other, it can result in decreased bass output in the frequency response area where they overlap each other.

The phase relationship between subwoofer and satellite speakers is very dependent on relative distance, construction and working principles of the main speakers. The figure on the left shows a case whereby phase of

incorrect in the critical overlap area, thus the listening room in that area.

To find the correct phase setting:

covers the overlap area.

0° and 180°.

Choose the setting for which you experience the most bass.

LFE / Slave IN

SUB I/O

SAT Output

OUT

To Slave

LFE Slave

100-120V/220-240V

50/60Hz 3.15A

ON

OFF

FUSE T3.15A L 250V

POWER

ON AUTO

GAIN

Min

SAT Highpass

Flat 60Hz 80Hz

SUB Lowpass

Max

PHASE

0° 180°

50Hz 150Hz

Operation

SAT/SUB Input

Setting the satellite cut-off frequency (Highpass)

Depending on the bass capabilities of the speakers, the frequency range of subwoofer and speakers can overlap between 50Hz and 150Hz. A bump or a gap in the frequency response and thus a lower sound quality will be experienced if the system is not matched properly.

In addition, small speakers and low powered amplifiers will particularly be affected by the low frequency signals, which again has an negative effect on the sound quality. Therefore it makes sense to limit the bass range of the connected speakers

LEFT

(called “satellites” in this case) by a highpass filter. The Dynaudio Sub 3 provides three settings to achieve this:

• Flat = no limitation

• 60Hz = frequencies below 60Hz are cut-off cut-off

To set the cut-off frequency:

Switch SAT Highpass control to

SUB I/O

SAT Output

Note

In most audio-video-systems the satellite cut-off frequency is already set in the bass management of your processor/ receiver. Please see the operating manual of your processor/receiver for further information.

You can decide whether you use the processor/receiver or the subwoofer for setting the cut-off frequency. Just take care, not to them to Flat.

To Slave

LFE Slave

100-120V/220-240V

50/60Hz 3.15A

OFF

FUSE T3.15A L 250V

Positioning the subwoofer

Positioning the subwoofer

Although it is often said that the location of a subwoofer in a listening room is not critical (as the human ear can not locate direction at very low frequencies), we recommend that you choose its position carefully. Thus the subwoofer can integrate seamlessly with the other speakers in the system and interact correctly with the room acoustics.

All of the following should be taken as rough guidelines; bass response in general is very dependent on the acoustics of the listening environment.

Finding the best position often involves a lot of trial-and-error experimentation.

Always trust your ears, even if the position of the subwoofer seemingly goes against the guidelines.

Contradictory as it may seem, good integration of subwoofers has been achieved when one isn’t aware that a subwoofer is present at all in the system, yet performance involves fast, deep and solid bass without sounding stressed, even at loud levels.

Choose adequate music material

When experimenting to find the optimal location, use a couple of music tracks with repetitive bass across a large spectrum. The tracks should be sufficiently different from each other and each should cover a wide bassrange. Musical instruments, such as a double-bass, bass guitar, church organ, etc. cover a wide spectrum in the bass region and are therefore very suitable.

Using non-music (such as action movies) material to position and adjust the subwoofer with, may lead to spectacular results with such material but almost always it will result in overblown and excessive bass when playing music with the same setting.

Impact of room-modes

Every listening environment will have specific “room-modes”, whereby in some specific locations in the room and at particular frequencies, the bass may be too much or too lean. This effect will be stronger in square and “shoe-box” shaped rooms. With a single subwoofer, the better position for the subwoofer relative to the listening position will be the one where bass is perceived to be neither too much nor too lean at any given frequency.

Avoid placing the subwoofer at

1/4, 1/2 or 3/4 of either the length or width of the room as at these locations the room-modes are likely to be strongest (the dashed lines in the figure)

1/4

1/2

3/4

1/4 1/2 3/4

Listening Room

Positioning the subwoofer

Positioning possibilities

Moving the subwoofer closer to walls and corners in particular will generally increase the amount of bass. Although the extra amount of bass can be compensated for by reducing the volume level of the subwoofer relative to the rest of the system, this can result in uneven bass response at the listening position. You can try starting with placement in a corner and experiment by gradually moving it out of the corner or further away from the wall. Try to locate the position which yields the best compromise between position, volume and even bass response. Note that every time that you reposition the subwoofer

(even if it’s over a short distance) you may need to adjust the level and phase settings again.

Corner placement

This placement yields maximum boost of bass level but potentially uneven distribution of bass in the room (roommodes), particularly if the room is square or shoe-box shaped.

From the listening position, check if the bass is even across the entire bass spectrum. If not, move the subwoofer out of the corner. Try moving it along either wall.

Next to wall, away from corner

This position still provides considerable boost but less than the corner placement as above. Room-modes can also still be considerable but less so than with corner placement.

From the listening position, check if the bass is even across the entire bass spectrum. If not, move the subwoofer away or towards your listening position until the most even response has been obtained.

Avoid placing the subwoofer exactly half-way or at a quarter of the wall’s length.

Free standing, away from wall and corner

This position will give least boost compared to wall or corner placement, but in general offers the best flexibility at achieving most even bass distribution at the listening position.

Avoid placing the subwoofer exactly half-way or at a quarter’s length of either sidewall.

Particularly in smaller square or

“shoe-box” shaped rooms the free standing position is recommended.

Using multiple subwoofers

By using carefully positioned multiple subwoofers it is possible to even out the different room-modes and thus create a more coherent overall bass response in the room. It is worth experimenting with different locations around the room for the additional subwoofers, even using the rear of the room. As adding subwoofers will not increase the effect of room-modes, even adding a subwoofer without much care or thought to positioning is likely to help even out room-modes.

General tips

General tips

Check it out

Try different subwoofer positions and settings, before you finally choose a setup.

Note down settings

When looking for the best subwoofer position in the room, note down the ideal setting you found for a position.

When moving the subwoofer between two positions you will be able to set the subwoofer to the same configuration as found before.

Vary the listening music

When experimenting to find the optimal settings, use a couple of music tracks with repetitive bass across a large spectrum. The tracks should be sufficiently different from each other and each should cover a wide bass-range.

Musical instruments, such as a doublebass, bass guitar, church organ, etc. covering a wide spectrum in the bass region and above, are very suitable as these depend on accurately balanced subwoofers and main speakers.

Verify changes

Although in general it is best to make adjustments in the sequence outlined below, note that changing one setting may influence another. For example, finding the right setting for phase may result in having to decrease gain, even if this was set correctly before.

It is recommended that you doublecheck the previous settings before moving on to the next one. Obtaining the best integration of the subwoofers generally involves a considerable amount of repeated fine-tuning.

50Hz

100Hz

150Hz

POWER

ON AUTO

GAIN

Min

SAT Highpass SUB Lowpass

Flat 60Hz 80Hz

Max

PHASE

0° 180°

Volume (GAIN)

50Hz 150Hz

Cut-off frequencies

With the GAIN control you can adjust the relative volume level of the subwoofer to the main speakers of the system:

Play the same track a couple of times, adjusting the level so that the important impact on the overall sound quality, when integrating a subwoofer into a audio-video-system. In general a large, floor-standing speaker still has across its range.

Matching the frequency responses of subwoofer and speakers has an

If you find that at certain specific bass tones the response is either too loud

(bloated sound) or soft (thin sound), it significant output in the deeper bass range, whereas a very small speaker will not be able to reproduce deep bass at all. In the first case a bump in the further with the location of the subwoofer and/or the cross-over settings.

Refer to the sections “Positioning the overlapping area will cause a louder or even bloated sound while in the second case an acoustic hole will be experienced. frequencies” on page 25 for further possible results (please note that all do not show exact filter characteristics).

LFE Slave

50 100 150 Frequency/Hz

Note

When using multiple subwoofers, ensure that the settings for cut-off frequency, phase and LF extension are identical. Use the LFE and

Slave mode options to ensure that all subwoofers operate on the same settings (refer to chapter

“Multiple subwoofer connections” on page 13).

Different acoustic loadings can be found within a listening room.

Thus, balancing out modes may require different power levels.

100-120V/220-240V

50/60Hz 3.15A

ON

OFF

FUSE T3.15A L 250V

General tips

Combined frequency response

Subwoofer

Main speakers

Combined frequency response

Subwoofer

Main speakers

Frequency/Hz

Subwoofer too low, main speakers too high

A gap in the frequency response occurs, if the cut-off frequency of the subwoofer is set too low and of the main speakers too high

(or if the main speakers are not able to reproduce low frequencies accordingly). In this acoustic hole you will miss some signal information and experience a thin bass sound.

Combined frequency response

Subwoofer

Main speakers

Frequency/Hz

Cross-over frequencies set correctly

Subwoofer and main speakers are perfectly matched, when the combined frequency response is smooth without bumps and gaps.

A neutral sound will be the result.

Frequency/Hz

Subwoofer too high, main speakers too low

In the other case you will experience unnatural and bloated bass sound, if the overlapping area is too large. The combined frequency response shows a bump, as the sound pressure levels in this area are increased.

POWER

ON AUTO

GAIN

Min

SAT Highpass

Flat 60Hz 80Hz

SUB Lowpass

Max

PHASE

0° 180°

50Hz 150Hz

Control possibilities

The Dynaudio Sub 3 provides two controls to match the frequency response of the subwoofer and the main speakers perfectly: frequency of the subwoofer, which can be continuously adjusted selected cut-off frequency the sound pressure level decreases rapidly.

• SAT Highpass: The lower cut-off frequency of the main speakers;

60Hz, 80Hz or Flat (neutral) can be selected. Below the selected cut-off frequency the sound pressure level

SAT Output

Note

Note: The settings for the crossover frequencies just have an impact on the signal at the SAT/

SUB Input! The LFE channel is just used to reproduce very low frequent effect signals.

Consequently signals at the SUB

I/O - LFE/Slave In are not limited in their frequency response.

SUB I/O

LFE / Slave IN

LFE Slave

OUT

100-120V/220-240V

50/60Hz 3.15A

To Slave

OFF

FUSE T3.15A L 250V

General tips

SUB Lowpass = 80Hz

The cut-off frequency should be selected as low as possible. Then the subwoofer works without being recognized as a single signal source.

Very often a cut-off frequency of

80Hz has been experienced as an ideal value.

Reduce weak amplifiers and small speakers from bass load

By limiting the reproduction of low frequency at the SAT Output, amplifiers and speakers connected to this output are freed from reproducing the heavy bass load, which negatively impacts the sound quality. This will improve the overall sound of your audio system.

Play a music track that has a significant amount of bass over a large bass region. An instrument such as a double-bass or bass-guitar is very suitable. Listen carefully to the bass-line played by the instrument. As it goes up and down in the bass range, the overall bass volume should remain the same – be it with very deep or higher bass notes.

Specific tips

Many processors/receivers provide extensive bass management capabilities to set the cut-off frequencies for both subwoofer and speakers. If using the bass management of the processor/ receiver, set the controls of the Sub 3 as followed:

• SUB Lowpass = 150Hz

(at the very right)

• SAT Highpass = Flat

CAUTION

Damage of small satellite speakers

Selecting the correct frequency depends to a large extend on the main speakers. Sometimes main speakers are specifically intended to work with a subwoofer. In such cases, the main speakers can get damaged by a fullrange amplifier signal.

If in doubt, check the instruction manual for the main speakers for any restrictions.

The table on the next page offers some setting tips for different speaker and amplifier combinations. This should only be taken as rough guidelines, as the best setup can just be found by experimenting.

Specific tips

Speaker/amplifier

Large speaker, powerful amplifier

Recommended first setting

SUB Lowpass SAT Highpass

50Hz Flat

If you experience this problem after first setting...

bass too bloated bass too weak

Large speaker, weaker amplifier

50Hz 60Hz bass too bloated

60Hz Flat bass too weak bass too bloated Medium sized speaker, powerful amplifier

60Hz 60Hz bass too weak bass too bloated Medium sized speaker, weaker amplifier bass too weak

Small speaker, powerful amplifier

80Hz 60Hz

Small speaker, weaker amplifier

80Hz 80Hz bass too bloated bass too weak bass too bloated bass too weak

Very small speaker

(Mini-satellites)

100Hz 80Hz bass too bloated bass too weak

...try this

Decrease volume (GAIN), SAT Highpass

= 60Hz