PT-LB75V Spec File
S
P
E
P ro d u c t N u m b e r :
PT-LB75V
P ro d u c t N a m e :
LCD Projector
C
F
I
As of August 2009. Specifications subject to change without notice.
L
E
< 1 >
S
P
E
C
F
I
L
E
Portable LCD Projector
PT-LB75V
Specifications
100–240 V AC, 50/60 Hz
300 W (0.9 W* 1 in standby eco mode. 15 W in normal standby mode.
18 W in normal standby mode when set to audio monitor out and with
fan stopped).)
Dichroic mirror separation/prism synthesis system
Optical system
0.63˝ (16 mm) diagonal (4:3 aspect ratio)
LCD panel
Panel size
Transparent LCD panel (x 3, R/G/B)
Display method
Active matrix
Drive method
786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Pixels
Stripe
Pixel configuration
Manual zoom (1:1–1:1.2), manual focus
Lens
F 1.65 –1.93, f 18.53 – 22.18 mm
1.4 –1.7:1
Throw ratio
220 W UHM lamp
Lamp
838–7,620 mm (33– 300 inches) diagonally, 4:3 aspect ratio
Projection size
Full color (16,777,216 colors)
Colors
2,600 lumens
Brightness* 2
85%
Center-to-corner uniformity ratio* 2
500:1 (full on/full off)
Contrast ratio* 2
1,024 x 768 pixels (Input signals that exceed this resolution will be
Resolution RGB
converted to 1,024 x 768 pixels.)
Horizontal: 15.00 – 91.00 kHz, Vertical: 50 – 85 Hz
Scanning frequency
RGB
480i (525i): fH 15.75 kHz; fV 60 Hz
YPBPR
576i (625i): fH 15.63 kHz; fV 50 Hz
480p (525p): fH 31.50 kHz; fV 60 Hz
576p (625p): fH 31.25 kHz; fV 50 Hz
720/60p (750p): fH 45.00 kHz; fV 60 Hz
720/50p (750p): fH 37.50 kHz; fV 50 Hz
1080/60i (1125i): fH 33.75 kHz; fV 60 Hz
1080/50i (1125i): fH 28.13 kHz; fV 50 Hz
NTSC, NTSC4.43, PAL-M, PAL60: fH 15.75 kHz; fV 60 Hz
S-Video/Video
PAL, SECAM, PAL-N: fH 15.63 kHz; fV 50 Hz
5:1 (fixed)
Optical axis shift
Approx. ±30° vertically
Keystone correction range
17 languages: English, French, German, Spanish, Italian, Korean,
On-screen menu
Russian, Chinese, Japanese, Swedish, Norwegian, Danish, Portuguese,
Polish, Hungarian, Czech, and Thai
Front/rear, ceiling/desk (menu selection)
Installation
4 x 2 cm, x 1, oval
Built-in speakers
Size
1.0 W (monaural)
Output power
D-sub HD 15-pin (female) x 1
Terminals
COMPUTER (RGB) 1 IN
G: 0.7 V [p-p] (1.0 V [p-p] for sync on green signals), 75 ohms,
RGB signal
R, B: 0.7 V [p-p], 75 ohms, HD/SYNC, VD: TTL (positive/negative
polarity compatible)
Y: 1.0 V [p-p] (including sync signal), 75 ohms,
YPBPR signal
PB, PR: 0.7 V [p-p], 75 ohms
D-sub HD 15-pin (female) x 1
COMPUTER (RGB) 2 IN
G: 0.7 V [p-p] (1.0 V [p-p] for sync on green signals), 75 ohms,
RGB signal
R, B: 0.7 V [p-p], 75 ohms, HD/SYNC, VD: TTL (positive/negative
polarity compatible)
Y: 1.0 V [p-p] (including sync signal), 75 ohms,
YPBPR signal
PB, PR: 0.7 V [p-p], 75 ohms
RCA pin x 1, 1.0 V [p-p], 75 ohms
VIDEO IN
Mini DIN 4-pin x 1, Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 ohms
S-VIDEO IN
COMPUTER (RGB) 1/2 AUDIO IN
M3 (L, R) x 1, 0.5 V [rms]
VIDEO/S-VIDEO AUDIO IN RCA (L, R) x 1, 0.5 V [rms]
M3 (L, R) x 1, 0 – 2.0 V [rms]
VARIABLE AUDIO OUT
D-sub 9-pin x 1, for external control (RS-232C compliant)
SERIAL
2 m/6.6´
Power cord length
Moulded plastic (PC+ABS)
Cabinet material
Power supply
Power consumption
As of August 2009
< 2 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Dimensions (W x H x D)
Weight* 4
Operating environment Temperature
Humidity
368 x 88 x 233 mm (14-1/2˝ x 3-15/32˝ x 9-3/16˝)*3
Approx. 2.96 kg (6.5 lbs.)
0°– 40°C (32°–104°F)
20%–80% (no condensation)
Remote control unit
3 V DC (AA battery x 2)
Approx. 15 m (49´3˝) when operated from directly in front of the signal
receptor
48 x 163 x 24.5 mm (1-7/8˝ x 6-13/32˝ x 31/32˝)
Approx. 117 g (4.1 oz) (including batteries)
Power supply
Operation range* 5
Dimensions (W x H x D)
Weight* 4
Supplied accessories
Power cord
Power cord secure lock
Wireless remote control
Batteries for remote control
VGA cable for RGB signals (1.8 m/5´11˝)
Carrying bag
Optional accessories
Replacement lamp unit: ET-LAB80
Ceiling mount bracket: ET-PKB80
*1:
*2:
*3:
*4:
*5:
In standby eco mode, only certain commands can be received from RS-232C control.
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
Protruding parts not included.
Average value. May differ depending on models.
Operation range differs depending on environments.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export control regulations. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS, Macintosh and Safari are trademarks of Apple Inc., registered
in the U.S. and other countries. All other trademarks are the property of their respective trademark owners. Projection images simulated.
As of August 2009
< 3 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Dimensions
9
(11/32˝)
97
(3-13/16˝)
88
(3-15/32˝)
54.5
(2-5/32˝)
3
(1/8˝)
233
(9-3/16˝)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
89
(3-1/2˝)
368
(14-1/2˝)
194
(7-5/8˝)
Terminals
3
1
6
7
As of August 2009
2
4
5
1
COMPUTER (RGB) 1 input
2
S-Video input
3
Video input
4
Audio input for Video/S-Video
5
Audio output
6
Serial input
7
COMPUTER (RGB) 2 input
8
Audio input for COMPUTER 1/2
8
< 4 >
S
P
E
F
C
I
L
E
PT-LB75V
Portable LCD Projector
Standard setting-up positions
357–437
(14-1/16˝–
17-7/32˝)
Adjustable
in 20-mm
(15/32-inch) step.
unit : mm (inch)
ø49
Upper edge of projected image
H
(1-15/16˝)
ø43
(1-11/16˝)
L
117
Projected image
L: Distance to screen
H: Height from the edge of screen to
center of lens
(4-19/32˝)
H
L
Lower edge of projected image
NOTE:
L
Projection size
Projection distance (L)
(diagonal)
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/ 33˝
/ 40˝
/ 50˝
/ 60˝
/ 70˝
/ 80˝
/ 90˝
/ 100˝
/ 120˝
/ 150˝
/ 200˝
/ 250˝
/ 300˝
Min (wide)
–
1.1 m
1.4 m
1.7 m
2.0 m
2.3 m
2.6 m
2.9 m
3.5 m
4.3 m
5.8 m
7.3 m
8.7 m
This illustration is not drawn to scale.
81 (3-3/16˝)
Projected image
Illustrations show the projector installed
using optional ceiling bracket.
65 (2-9/16˝)
70 (2-3/4˝)
/
/
/
/
/
/
/
/
/
/
/
/
/
–
3.7´
4.7´
5.6´
6.6´
7.6´
8.5´
9.5´
11.4´
14.3´
19.0´
23.8´
28.6´
Max (telephoto)
1.1
1.4
1.7
2.1
2.4
2.8
3.1
3.5
4.2
5.2
7.0
8.7
10.5
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
3.7´
4.5´
5.6´
6.8´
7.9´
9.1´
10.2´
11.4´
13.7´
17.1´
22.9´
28.7´
34.4´
Height from the edge of screen
to center of lens (H)
0.08
0.10
0.13
0.15
0.18
0.20
0.23
0.25
0.30
0.38
0.51
0.64
0.76
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
0.28´
0.33´
0.42´
0.50´
0.58´
0.67´
0.75´
0.83´
1.00´
1.25´
1.67´
2.08´
2.50´
* This distance is especially recommended for ceiling-mounted use and other
permanent installations.
NOTE:
Values shown are approximate.
The value for L (distance to screen)
varies slightly depending on the zoom
lens characteristics.
When the shortest projection distance is
used, a small amount of distortion may
occur in the image due to the zoom lens
characteristics.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4 : 3
minimum
L (m) = (diagonal screen size in inches) x 0.0292 – 0.036
maximum
L (m) = (diagonal screen size in inches) x 0.0351 – 0.044
NOTE: Distances calculated with the above equations will include a slight error.
Installable Angle
Install the projector at an angle within the range shown below.
• Horizontal direction
The projector may be installed at a horizontal angle of ±10°.
As of August 2009
10 ° 10 °
-30°
+30°
• Vertical direction
The projector
may be installed
at a vertical
angle of ±30°.
< 5 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 193 MHz dot clock.
NOTE:
Pixel thinning is applied to signals that exceed a dot clock frequency of 110 MHz. The display resolution of this projector is 1,024 x 768
pixels. Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
List of compatible signals
Display mode
Display
resolution
(dots) 1
Scanning frequency Dot clock
H
V
frequency
(kHz)
(kHz)
(MHz)
Picture Input terminal
quality 2
NTSC/NTSC4.43/PAL-M/PAL60
720 x 480i
15.7
59.9
–
A
PAL/PAL-N/SECAM
720 x 576i
15.6
50.0
–
A
525i (480i)
720 x 480i
15.7
59.9
13.5
A
625i (576i)
720 x 576i
15.6
50.0
13.5
A
525p (480p)
720 x 483
31.5
59.9
27.0
A
625p (576p)
720 x 576
31.3
50.0
27.0
A
750 (720)/60p
1280 x 720
45.0
60.0
74.3
A
750 (720)/50p
1280 x 720
37.5
50.0
74.3
A
1920 x 1080i
33.8
60.0
74.3
A
28.1
50.0
74.3
A
31.5
70.1
25.2
A
37.9
85.1
31.5
A
1125 (1080)/60i
1125 (1080)/50i
VESA70
640 x 400
VESA85
640 x 480
31.5
59.9
25.2
A
VGA65
35.0
66.7
30.2
A
VGA72
37.9
72.8
31.5
A
VGA75
37.5
75.0
31.5
A
VGA85
43.3
85.0
36.0
A
35.2
56.3
36.0
A
SVGA60
37.9
60.3
40.0
A
SVGA70
48.1
72.2
50.0
A
SVGA75
46.9
75.0
49.5
A
SVGA85
53.7
85.1
56.3
A
VGA60
SVGA55
800 x 600
MAC16
832 x 624
49.7
74.6
57.3
A
XGA50
1024 x 768
39.6
50.1
51.9
AA
XGA60
48.4
60.0
65.0
AA
XGA70
56.5
70.1
75.0
AA
XGA75
60.0
75.0
78.8
AA
XGA85
68.7
85.0
94.5
AA
44.8
59.9
74.5
A
37.1
49.8
60.5
A
39.6
49.9
65.3
A
47.8
59.9
79.5
A
41.3
50.0
68.0
A
49.1
60.2
69.1
A
49.7
59.8
83.5
A
64.0
71.2
94.2
A
MXGA75
67.5
74.9
108.0
A
MXGA85
76.7
85.0
121.5
B
WIDE750 (720)
WXGA768
WXGA800
MXGA70
1280 x 720
1280 x 768
1280 x 800
1152 x 864
MAC21
1152 x 870
68.7
75.1
100.0
A
MSXGA60
1280 x 960
60.0
60.0
108.0
A
1280 x 1024
64.0
60.0
108.0
A
80.0
75.0
135.0
B
91.1
85.0
157.5
B
64.0
60.0
108.0
A
65.1
59.9
122.4
B
SXGA60
SXGA75
SXGA85
SXGA60+
WXGA+
1400 x 1050
1440 x 900
55.9
59.9
106.5
A
UXGA60
1600 x 1200
75.0
60.0
162.0
B
WSXGA+
1680 x 1050
65.3
60.0
146.3
B
WUXGA
1920 x 1200
74.6
59.9
193.3
B
VIDEO/S-VIDEO
COMPUTER (RGB/YP B P R )
COMPUTER (RGB only)
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A
Signals are converted by the image processing circuit before picture is projected.
B
Signals are compressed by the image processing circuit before picture is projected.
As of August 2009
< 6 >
S
P
E
F
C
I
L
E
PT-LB75V
Portable LCD Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6 9
1
5
No. Signal name
Description
No. Signal name
Signal name
1
–
NC
6
–
NC
2
TXD
Send data
7
CTS
Connected internally
3
RXD
Receive data
8
RTS
Connected internally
4
–
Connected internally
9
–
NC
5
GND
Ground
D-sub HD 9-pin, female
Communication conditions (factory setting)
Signal level
RS-232C-compliant
Synchronization method
Start-stop synchronization
Baud rate
9,600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
C1 C2 C3
Start
(1 byte)
:
P1 P2 P3 P4
Colon
Parameter
Command
(1 byte)
(1-4 bytes)
(3 bytes)
(Control and/or query commands)
ETX
End
(1 byte)
CAUTION
It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then
try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector
before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for
command response to 10 seconds or more.
NOTE:
If a wrong command is received, the projector will send an ER401 command to the computer.
When sending commands without parameters, a colon (:) is not necessary.
Cable specifications
Projector
1
PC (DTE)
NC
NC
3
3
4
NC
NC
DSR
NC
8
8
As of August 2009
6
7
7
9
4
5
5
6
1
2
2
NC
NC
9
< 7 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Control commands
Command: <Parameter>
Function
Callback: <Parameter>
P O N * 1/* 2
P O F * 1/* 2
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off on>
OEN
OXG:0
OXG:1
OXG:2
VPM:<NAT>
VPM:<STD>
VPM:<DYN>
VPM:<BBD>
VPM:<WBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
O S H *1
OIX
DZU
DZD
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
The same function as “default” button
Freeze
Enter
Wide mode: Off
Wide mode: On
Wide mode: Auto
Picture mode: Natural
Picture mode: Standard
Picture mode: Dynamic
Picture mode: Blackboard
Picture mode: Whiteboard
Daylight View: Off
Daylight View: Auto
Daylight View: On
Volume up
Volume down
Menu
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
AV mute
Index window
Digital zoom: Enlargement
Digital zoom: Reduction
PON * 1/* 2
POF * 1/* 2
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off on>
OEN
OXG:0
OXG:1
OXG:2
VPM:<NAT>
VPM:<STD>
VPM:<DYN>
VPM:<BBD>
VPM:<WBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
OSH * 1
OIX
DZU
DZD
*1
*2
Parameter value
Min
Max
–
–
0
–
–
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.
As of August 2009
< 8 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Status asking commands
Command
Description
QP W
Q$ S
QI N
QA V
QV C
QV T
QV B
QV R
QV S
QW R
QW G
QW B
QH P
QV P
QC P
QD C
QS P
QL G
QX G
Standby power status
Lamp status
Input signal status
Volume adjustment value
Color adjustment value
Tint adjustent value
Brightness adjustment value
Contrast adjustment value
Sharpness adjustment value
White balance: R adjustment value
White balance: G adjustment value
White balance: B adjustment value
Horizontal position adjustment value
Vertical position adjustment value
Clock phase adjustment value
Dot clock adjustment value
Projection method status
On-screen menu language
Wide mode status
Off
On
Auto
Daylight View status
Off
Auto
On
Picture mode status
Natural
Standard
Dynamic
Blackboard
Whiteboard
Freeze status
Lamp run time
Shutter function status
Keystone correction status
Color temperature adjustment status
QV X : D L V I 0
QP M
QF Z
Q$ L
QS H
QK S
QT E
Callback
<Parameter>
<power condition>
<lamp condition>
<input signal>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<0>
<1>
<2>
<+00000>
<+00001>
<+00002>
<NAT>
<STD>
<DYN>
<BBD>
<WBD>
<off_on>
<acctch>
<off_on>
<pl>
<color temp>
Parameter format
Parameter format
<pl>
Size (Byte)
<off on>
<input signal>
<installation>
<language>
3 (1 or 2 bytes also
possible when
under control)
1
3
1
3
<power condition>
<lamp condition>
3
1
<acctch>
<color temp>
<date>
4
1
8
<time>
6
Definition
Decimal without signs: 0 to 999 (000, 001, 002...999)
Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
Callback from the projector is 3 Byte.
0 = off, 1 = on
RG1 = computer 1, RG2 = computer 2, VID = video, SVD = S-Video
0 = front, 1 = rear, 2 = ceiling and front, 3 = ceiling and rear
ENG = English, DEU = German, FRA = French, ESP = Spanish,
ITL = Italian, JPN = Japanese, CHI = Chinese, POR = Portuguese,
SVE = Swedish, NOR = Norwegian, DAN = Danish, POL = Polish,
CES = Czech, MAG = Hungarian, RUS = Russian, THA = Thai, KOR = Korean
000 = power off (standby mode off), 001 = power on (standby mode on)
0 = standby, 1 = lamp on under control, 2 = lamp off,
3 = lamp off under control
Decimal without signs: 0000-9999 hours
0 = economy, 1 = normal, 2 = high
y1y2y3y4m1m2d1d2w = year (y) month (m) day (d) day of week (w)
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
h1h2m1m2s1s2 = hour (h) minute (m) second (s)
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown right.
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of August 2009
STX
Start
AVL
:
Command
30
ETX
Parameter
End
< 9 >
S
P
E
C
F
I
L
E
PT-LB75V
Portable LCD Projector
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3.
If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the
projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
200 mm (7-7/8˝)
or more
500 mm (19-11/16˝)
or more
500 mm (19-11/16˝)
or more
Direction of air intake and exhaust
Intake
Exhaust
Operating the projector continuously
1.
If the projector is to be operated continuously 10 hours or more, lamp replacement cycle duration
becomes shorter.
2.
The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods (one hour or less).
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export control regulations. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS, Macintosh and Safari are trademarks of Apple Inc., registered
in the U.S. and other countries. All other trademarks are the property of their respective trademark owners. Projection images simulated.
As of August 2009
< 10 >
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising