LDX-EXP-E SERIES

LDX-EXP-E SERIES
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
TYPICAL SPECIFICATIONS
Supply and install the Ready-Lite® LDX-EXP-E Series of hazardous location battery unit equipment. The battery
unit housing will be constructed of Die-Cast aluminum with grey epoxy powder coat finish. The equipment
shall be rated for 120, 277 or 347V, 60 Hz input and be CSA listed. The equipment shall have an output of
V and
W and shall supply the rated load for minimum of 1/2 hour to 87.5% of the
rated battery voltage. The battery shall be a long-life, maintenance-free Lead-Calcium type. The charger shall
be fully computer tested and have its charge voltage set in the factory to ± 1% tolerance. The charger shall be
current limited, temperature compensated, short circuit proof and reverse polarity protected. The charger shall
be furnished with an electronic lockout circuit, which will connect the battery when the AC circuit is activated,
and an electronic brownout circuit, which will activate the emergency heads when the utility power dips below
75% of nominal voltage. Where required the equipment shall come complete with
heads, each
of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum
with grey epoxy powder coat finish. The lenses shall be a clear, impact and heat resistant prismatic glass globe.
The head shall be factory sealed, with no need for external seals. Where required the equipment shall come
complete with one Exit Sign and will include a transfer panel to maintain the Exit Sign permanently lighting in
both normal and emergency operation. The exit housing shall be industrial grade 14-gauge steel and finished
in grey enamel. The faceplate will be constructed of heavy-duty 14-gauge steel and feature universal knockout
chevrons and the red letters shall not be less than 6” in height with a 3/4” stroke. The sign shall include an
LED lamp with ALINGAP LEDs and shall consume less than 5W in either AC or battery mode.
, Division
, Group
. The Exit Sign shall be CSA-C860
The equipment shall be suitable for Class
approved and meets CSA C22.2 No.141
The equipment shall be Ready-Lite® Model:
.
LDX-EXP-E SERIES
Battery Units,
Self-Powered Exit Signs
& Combination Units
CSA CERTIFIED FOR USE IN
HAZARDOUS LOCATIONS
The LDX-EXP-E Series of battery equipment is
designed to cover emergency lighting applications for the entire spectrum of hazardous
locations, where flammable gases, vapors,
liquids, dust particles, fabrics or tissues are
permanently present or are likely to exist.
In one simple-to-order catalogue family the
LDX-EXP-E Series combines three traditional
emergency lighting products with battery
back-up: battery units with emergency
lights, Self-Powered Exit Signs, and combination units with emergency lights and Exit
Sign. The equipment is also available with
additional emergency power capacity to
drive remote heads and Exit Signs.
POWER CONSUMPTION AND UNIT RATING
MODEL
LDX636EXP
LDX672EXP
LDX6108EXP
LDX1272EXP
LDX12144EXP
LDX12200EXP
LDX24144EXP
LDX24288EXP
FEATURES
• CSA Certified for use in hazardous
locations:
- Class I, Divisions 1 and 2, Groups
B, C, D
- C
lass II, Divisions 1 and 2, Groups
E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey
epoxy powder coat finish; clear, impact
and heat resistant prismatic glass globe
• L ong-life, maintenance-free
Lead-Calcium battery
• Battery charger is current limited,
temperature compensated, short-circuit
proof and reverse polarity protected
• Emergency heads with one or twin
lamp design
• Self-Powered combo includes a transfer
panel to drive four remote LED-based
remote Exit Signs
• Exit Sign uses an LED lamp with
ALINGAP LEDs
• The Self-Powered version is CSA C22.2
No. 141 certified
AC SPECS
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
120/347VAC
30MIN
1H00
36
72
108
72
144
200
144
288
21
42
63
42
84
117
84
168
WATTAGE CAPACITY
1H30
2H00
15
30
45
30
60
83
60
120
4H00
12
24
36
24
48
67
48
96
6
12
18
12
24
33
24
48
NOTE: The wattage capacity applies only to the battery unit. For combo or Self-Powered Exit Signs one must allocate 5W of emergency
power for each sign.
n
TEMPERATURE CODES: MEASURED AT 40°C AMBIENT
Explosion-proof equipment is composed of one or more modules, each of them qualified for a specific temperature code. The temperature code of the complete equipment (enclosure + exit sign + emergency heads)
is defined as the most severe of the temperature codes identified for each of the modules below.
1. TEMPERATURE CODES FOR LDX-EXP-E SERIES (BATTERY UNIT ENCLOSURE)
SEVERITY CODE
S1
S2N
S3
S4
TEMPERATURE CODE
T6
T6
T6
T6
2. TEMPERATURE CODES FOR RFX-EX SERIES* (EXIT SIGN)
SEVERITY CODE
S1
S2N
S3
S4
TEMPERATURE CODE
T6
T6
T4A
T6 (E, F, G)
*Self-Powered Exit Sign only (no heads).
3. TEMPERATURE CODES FOR RFX SERIES (EMERGENCY HEADS)
SEVERITY
CODE
Quartz bi-pin
12W, 20W
MR16
12V-12W
MR16
12V, 24V-20W
MR16
12V, 24V-35W
MR16
12V, 24V-50W
MR16
120V-20W
MR16
120V-35W
MR16
120V-50W
S1
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
S2N
T5 (100o C)
T6 (85o C)
T5 (100o C)
T4A (120o C)
T3C (160o C)
T5 (100o C)
T3A (180o C)
T3 (200o C)
T1 (450
T4 (450
T3 (200
S3
S4
o
C)
T4A (120o C)
(E,F,G)
o
C)
T5 (100o C)
(E,F,G)
90
o
C)
T5 (100o C)
(E,F,G)
T2 (300
o
C)
T4A (120o C)
(E,F,G)
T1 (450
o
C)
T3C (160o C)
(E,F,G)
T2D (215
o
C)
T4A (120o C)
(E,F,G)
T2 (300
o
C)
T3C (160o C)
(E,F,G)
T1 (450o C)
N/A
Type:
new features
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
DIMENSIONS
Dimensions are approximate and subject to change.
SMALL CABINET (36-72W)
20-7/8” [53 cm]
Battery Units,
Self-Powered Exit Signs
& Combination Units
22-7/8” [58.2 cm]
19-5/8” [50 cm]
22-7/8” [58.2 cm]
18-1/4” [46.5 cm]
LDX-EXP-E SERIES
6-3/8” [16.3 cm]
9-5/8” [24.4 cm]
19-5/8” [50 cm]
10-3/8” [26.4 cm]
27-3/4” [70.5 cm]
14-3/8” [36.6 cm]
LARGE CABINET (108-288W)
21-1/4” [53.9 cm]
23-3/4” [60.4 cm]
23-3/8” [59.2 cm]
20-1/8” [51 cm]
23-3/8” [59.2 cm]
8-1/4” [20.8 cm]
10” [25.4 cm]
20-1/8” [51 cm]
13-1/8” [33.3 cm]
30-5/8” [77.8 cm]
14-3/8” [36.6 cm]
ORDERING INFORMATION
Identify the environment of your application: Class
, Division
Refer to table 4 for the Severity Code to use in your catalogue number.
, Group
.
4. SEVERITY CODE SELECTION CHART
ENVIRONMENT
SEVERITY CODE
Cl. I, Div. 1&2, Gr. B
S1
Cl. I, Div. 1&2, Gr. C, D
S2N
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G Cl. III, Div. 1 & 2
S4
ORDERING CHART
DC
VOLTAGE
LDX6= 6V
CAPACITY
CABINET SIZE
-36= 36W (S)*
-72= 72W (S)*
-108= 108W (L)*
SERIES
EXP
LDX12= 12V -72= 72W (S)*
-144= 144W (L)*
-200= 200W (L)*
LDX24= 24V -144= 144W (L)*
-288= 288W (L)*
HEAD STYLE
SEVERITY CODE
LAMPS
Blank= no
heads
/11= s ingle
remote,
1 lamp
/12= s ingle
remote,
2 lamps
/21= d
ouble
remote, 1
lamp each
S1= CL.1, Div.1&2, Gr. B
S2N= CL.1, Div.1&2, Gr. C, D
S3= CL.1, Div.2, Gr. B, C, D
S4= CL.II,
Div.1, & 2 Gr.E, F,
G CL.III, Div.1 & 2
*Cabinet size
not part of
nomenclature
EXAMPLE: LDX6-36EXP/11S112-E1
91
FACES
Blank= no lamp
-E1= single face
12= h
alogen, 6V, 12V exit Sign,
12W, bi-pin
C860 LED
20= h
alogen, 6V to 24V-E2= double face
20W, bi-pin
exit sign,
M12= MR16 halogen,
C860 LED
12V-12W,
M20= MR16 halogen,
12V, 24V-20W
M35= MR16 halogen,
12V, 24V-35W
M50= MR16 halogen,
12V, 24V-50W
MH20= MR16-IR 12V-20W,
high-output
MH35= MR16-IR, 12V-35W,
high-output
MH50= MR16-IR 12V-50W,
high-output
AC VOLTAGE
OPTIONS
Blank= 120VAC
U277= 277VAC
U347= 347VAC
Blank= no
options
D3= time delay
(15 mins.)
TP= transfer
panel
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement