Page 1 Parts list for the SP9 4-gallon Knapsack Sprayer Pump lever

Page 1 Parts list for the SP9 4-gallon Knapsack Sprayer Pump lever
Parts list for the [email protected] 4-gallon Knapsack Sprayer
Parts Depots, for original SP parts.
NORTH AMERICAN WHOLESALE PARTS, INC.
Phone: (800) 286-0679 Fax (612) 487-3943
WESTHEFFER COMPANY, (NC.
Phone: (913) 843-1633 Fax: (913) 843-4486
JOHN BROOKS COMPANY LIMITED
Toronto Phone: (905) 624-4200 Fx (905) 624-6379
Calgary Phone: (403) 201-1180 Fac (403) 291-0542
==" Systems.
1618 Stanford Street, Suite "C”, Santa Monica, CA 90404
(310) 449-1492 (800) 457-3440 FAX (310) 478-4175
E к с»
ANN
34 Al
В
5
Ё
e
25 Z 25555 9 959595232555 53533522 2395959 SSADARAS
A ACCEDA
AN eho
му NDA Ds IS
=. e er A
Lt
y
at
eS
ER
Cap w/seal & handle 6”.
Seal for cap 6”.
Check valve for cap.
Tank w/nyion bearing.
Nylon bearing.
Pump lever (fold-back type).
Screw and nut set.
Pump handle (fold-back
[19.1
[43 VH 12.9]
onen
L
Say (29.1)
с x1
[
[12 1H 43.1]
[49.1]
Hose set (rubber)
Complete spray pisto! v/vullt
ln filter & grip.
Spindle set
Spindle "O7ring set.
Rubber washer.
Plug set
Brass spray wand.
Plastic spray wand.
Nozze holder.
Adjustable brass nozzle with
holder,
Plastic spray tip set (2-8004
& 1-TK-S)
Spray tip "O”ring set
Bell hooks.
Aluminum spray wand
Shoulder pads.
Complete cylinder assembly
new sealing System SPO.
Diaphragm protector, hall
moon jaws & clamp.
Piston pump holder & guide.
Diaphragm, plastic piston &
internal seal.
Agtating hase, clamps & tank
_ connector.
Kit 48.1 Complete piston diaphragm
assembly.
E 49.1 Complete pump module.
Kit 180 Locking pln-pump handle
(small).
KA 181 Locking pln-pump handle
(large).
Kt FILT Filter for kt 18F.
Kit GRIP Grip handle for kit 18F.
NOTE: + Not supplied with unit. See
sheet of accessories.
— — — À mA mA
$3 ~~ с
na
NENE
Mm,
9
—
_
Zy--HETe1 +
DZ
RES) (49.1)
N
28 Y END
m
=
56 E 568
5
à
NOTE:
For best results, the sprayer should be pumped every 5
seconds on a continuous basis. This will maintain your
spraying pressure. If you do not pump, you will not have
pressure to spray
If you have a question or a problem please call us at
1-800-457-3440
We will answer any question you may have.
The [email protected] Knapsack Sprayer
”
We would like to congratulate you on the purchase of your new SPQ. The sprayer that altows you the easiest, most com-
fortable way of carrying out your farm and garden projects with the revolutionary piston-diaphragm pump (patented), that
all but eliminates the problems inherent in most sprayers.
As a new owner of the skillfully engineered SPP, we strongly recommend you carefully read and follow all the information
on this sheet before use, and then save for future reference.
Please read the attached trouble shooting guide.
HOW TO ASSEMBLE
1.
2.
Attach spray wand to spray gun and tighten firmly.
Take pump handie Kit 7 (solid) and insert into the tube on the pump lever Kit 5 ("T™ shape lever on sprayer), you will
notice holes drilted through both sides of both the pump handle and the pump lever. Align these holes, take the "R"
pin provided and place through the holes. This affixes the handle in place and is ready for use.
For storage reverse process and then place "R" pin through the pump lever Kit 5 to keep from losing "R” pin.
Instructions for instafling shoulder strap plastic buckle:
First putthe sprayer on a hard flat surface, take the white plastic buckle and while holding the sprayer up slightly. place
buckle under the tubular metal frame. Stowly push down forcing the frame into the buckle. Repeatthe same procedure
for other side.
HOW TO PREPARE YOUR UNIT FOR USE
1.
2.
3.
4
Remove cap.
Mix solution in a separate receptacle, following manufacturers directions on the container.
Pour pre-mixed solutions into sprayer and cap.
Place sprayer on back and pressurize tank by pumping approximately 10 to 15 times. For best results, the sprayer
should be pumped every § seconds on a continuous basis. This will maintain your spraying pressure. If you
do not pump, you will not have pressure to spray.
Always oil the seal on cap of unit as well as the check valve, this will extend life of seal and is important for obtaining
proper seal with no leaks.
A unit that has been used with herbicides should never be used to spray insecticides, unless the sprayer has been
propery cleaned and all other chemicals neutralized. Failure to do this could cause you to kill plants that have been
sprayed. Consuit with the manufacturer of the chemicals in use to obtain proper instructions.
HOW TO CLEAN AND MAINTAIN
1.
2.
3.
CAUTIONS
Remove cap and pour out remaining solution, then rinse all parts thoroughly with clean water.
Leaving approximately 1/2 gallon of fresh water in tank, pressurize and flush pumping system by depressing trigger
at least 2 minutes, then drain all remaining water.
Always store tank clean and empty in a dry, shaded location.
/ Please read and follow all Instructions before using sprayer. в
— Before using, filling or cleaning any sprayer, read afl parts of the operating instruchons.
Make sure to set up the sprayer exactly as explained In the printed operating instructions, reminder tags and/or stickers.
Faure to follow
manufacturers
recommendation
on use and care of
unit will void any
expressed or im-
plied warranty.
Do not use chlo-
rine or clorox. It
will permanently
damage pump
system.
Wear protective clothing, respirator, gloves, eye protection, etc. whenever using, filling, or cleaning sprayer.
Periodically re-grease lid gasket as well as lid vent and pump cylinder, where applicable.
To ensure good performances, keep lid vent free of obstruction. Before and after each use, make sure all connections are well
bghtened. Service and replace wom parts as required
Read and follow all instructions of the chemical suppliers.
As a rule, mix your chemicals in a separata container from which to fill the sprayer. Do not mix formulas inside the sprayer.
Where an exception ks made (e.g. with quid fertilizers), fill sprayer with water BEFORE adding the active ingredient.
Always sift formula through the screen. H there is no built-in strainer, use a screened funnel.
Never fill the sprayer with hot fiquids. Max. 30°C, or 85°F.
This sprayer is mads to handle agrichemicals in their usual water or oil solutions. Do not use flammable, corrosive or caustic
solutions.
Never use gasoline or other flammable materials.
Before cleaning or servicing the sprayer, allow all pressure to escape. Do not store or transport sprayer under pressure.
After each usa, wash the sprayer—inciuding hese, lance and shut-off valve—with plenty of fresh water. Unless spraying is
to be continued within hours, drain chemical formula and thoroughly rinse the tank and all kiquid ducts.
Never store chemicals in your sprayer for any length of time.
Use the sprayer only for the kind of jobs for which it was designed. When in doubt, ask your dealer.
Do not leave the sprayer in reach of children or persons not qualified to handle it in proper fashion.
When not in use—and especially during prolonged storage—keep your sprayer in a protected place away from direct
solar heat
Make sure the spray hose loops freely without kinking or squeezing.
Always use SP Systems onginaf replacement parts. DSPP-0396
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement