12140B_12145B_12200B IB Dbl Bedrail IB 1-4

12140B_12145B_12200B IB Dbl Bedrail IB 1-4
12140B/12145B/12200B
TO LOOSEN BEDRAIL FOR REMOVAL:
Please read the following instructions
and warnings carefully.
Push release lever up on support leg while pulling
bedrail away from mattress. Repeat on other
end (Figure Q).
Keep this instruction manual
for future reference.
Adult assembly required.
CAUTION: Do not push strap lock lever down.
For Technical Support Call
1-800-268-6237 or E-Mail at
[email protected]
Q
For use with children 2-5 years of age.
T O C L E AN:
To clean this Sure and Secure Double Bedrail, surface wash with damp sponge, mild soap
and cold water. Rinse and lay flat to dry. Do not remove fabric cover from frame.
INST RUCT ION MANUAL
S U RE & S E CU RE ®
D O U B L E B ED RA I L
(colors & styles may vary)
Suffocation and Strangulation Hazard. Death or Serious Injury Can Occur:
• Infants who cannot get in and out of an adult bed without help can be trapped
between a mattress and a wall and suffocate. NEVER place infants in adult beds
with or without bedrail.
• BEDRAIL USE: Bedrail can trap young children against mattress, headboard, or footboard.
• Use only for children who have outgrown a crib. NEVER use in place of a crib.
• Use only with children who can get in and out of adult bed without help.
• ALWAYS keep bedrail pushed firmly against mattress and at least 9 inches from
headboard and footboard.
• NEVER use on toddler bed, bunk bed, water bed, or bed with inflatable mattress.
Use only on adult bed with mattress and box spring or platform bed (support board 5/8"
nominal thickness).
• ENTRAPMENT HAZARD: Death or Serious Injury Can Occur if bedrail is used without
fabric cover. Never use without fabric covering metal frame.
• Discontinue use if damaged,broken, or if parts are missing.
We LOVE our customers!
Get to know us at:
www.summerinfant.com
We at Summer Infant stand behind all of our products. If
you are not completely satisfied or have any questions,
please contact our customer service department at
1-800-268-6237 or [email protected]
(For Europe call +44 (0)208 420 4429 or
[email protected])
4
Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
Summer Infant Europe, LTD.
Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire WD 23 3HP
+44 (0) 208 420 4429
© 2007 Summer Infant, Inc.
Please retain information for
future reference.
Colors and styles may vary.
MADE IN CHINA
6/09
Periodically check the bedrail for tightness to ensure
bedrail is snug against bed.
F E ATU RE S & C OMP O N E N T S :
S E T U P:
Connector
(2)
Step 8:
Remove mattress from bed.
Step 9:
Position bedrails on boxspring and replace mattress (Figure I).
Bedrail Frame (2 sets)
(6 connector tubes & 4 end panels)
Fold-down
Support Leg (4)
Fabric Panel (2)
9“ Template
1
2
3
4
5
6
7
8
9
S ET U P:
Step 1:
Insert top, middle and bottom connector
tubes into each end rail (Figure A).
A
pins
Note: Top and bottom connector tubes
have pins on each side, and the pins snap
into end rails. Middle connector tube does
not have pins.
Step 11:
While holding the bottom corner of the bedrail pull the strap
to proper tension until tight against the mattress (Figure J).
Repeat on the other end of the bedrail.
At Least 9“
At Least 9“
Mattress
Headboard
Footboard
Lock
pin
L
B
Step 4:
Place fabric panel completely over bedrail
frame and slide down (Figure F).
C
Lock
engaged
Note: Assure that bottom rail is covered
by fabric panel.
Step 5:
Zipper bottom of fabric cover over bottom
rail to fasten. Attach hook & loop flap
to cover opening.
D
E
F
Step 6:
Repeat steps 1-5 for other bed rail.
Tuck excess strap
under mattress
S E T U P:
IMPORTANT NOTE: To Ensure
against entrapment hazards, make
sure there are no gaps between the
bedrail and the mattress. Slight
deformation of the mattress is
acceptable. See diagram at right.
mattress
box spring
T O F O LD DOWN B E DR AI L:
Step 7:
This bedrail fits twin, full and queen size
mattresses. Plug each connector into the
support leg of the bedrail without strap
clips. Next, connect the strap clip of the
other bedrail to the connector
(Figures G & H).
Raise locking pins up on both
sides of the bedrail’s support
leg and fold down bedrail
(Figures O & P).
O
2
K
Bedrail Panel
pins
Step 3:
Fold down support legs as shown in
Figure D, until spring lock is engaged
(see Figure E).
J
Release Lever
NOTE: Press release lever down when strap is tight to lock
strap in place (Figure K). Roll up excess strap and tuck under
mattress (Figure L).
no pins
Step 2:
Insert support leg into end of bedrail
frame and snap into place (Figures B & C).
Take second support leg and repeat on
other side.
I
Step 10:
Ensure the bedrail is centered on the mattress end to end.
Using enclosed template, measure AT LEAST 9 inches
between the ends of the bedrail and the headboard and
footboard. See diagram below.
G
H
P
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement