AII42446 CD Changer Attachment

INSTALLATION
INSTRUCTIONS
Accessory
Application
Publications No.
CD CHANGER
(TRUNK MOUNT)
2010 CIVIC
4-DOOR
(VP, LX, LX-S, EX, EX-L)
AII 42446
PARTS LIST
Issue Date
AUG 2009
8 Cushion tapes
CD Changer Attachment (Sold Separately)
P/N 08B26-SNA-101
CD changer bracket
Bus cable
4 Washer-screws
2 Side brackets
3 Clip nuts
CD Changer Kit (Sold Separately)
P/N 08A26-5E1-101
CD changer
3 EPT seals
3 Washer-bolts
4 Flange nuts
15 Wire ties
2 Wire ties with clip
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
Bracket (Not Used)
8-Disc CD magazine
8 Washer-screws, 4 x 6 mm
Accessory User's
Information Manual
AII 42446 (0908)
08V31-SDN-1010-91
1 of 11
3.
TOOLS REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Stubby Phillips screwdriver
10 mm combination wrench
Clip remover
8 mm and 10 mm Sockets
Ratchet
Small flat-tip screwdriver
Contact cleaner
Shop towel
Inside the passenger's compartment area,
remove the rear seat cushion by removing the
bolt and releasing the two hooks.
BOLT
Illustration of the CD Changer Installed on the
Vehicle
AUDIO UNIT
CD CHANGER
HOOKS
REAR SEAT CUSHION
T
4.
Remove the right rear seatback side frame by
removing the bolt.
RIGHT
REAR SEATBACK
SIDE FRAME
BUS CABLE
H
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only
by skilled technicians who have the proper
tools, equipment, and training to correctly and
safely add equipment to your car. These
procedures should not be attempted by “do-ityourselfers.”
BOLT
Routing the Fog Light Harness
T
1.
Make sure you have the anti-theft code for
the audio unit, then write down the
frequencies for the preset buttons.
2.
Disconnect the negative cable from the
battery.
2 of 11
AII 42446 (0908)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
5.
Open the trunk lid, and remove the trunk floor by
removing the two clips.
2 CLIPS
TRUNK
FLOOR
MAT
8.
Inside the trunk, fold the right rear seatback
forward by pulling the lever under the rear parcel
shelf.
9.
Continue removing the weatherstrip in the area
shown. Remove the five clips, then pull out on the
right trunk side trim panel in the direction shown.
RIGHT REAR
SEATBACK
CLIPS
CLIPS
(Turn the center pin
in a counterclockwise
direction to remove.)
LEVER
6.
Remove the trunk weatherstrip from the edge of
the trunk opening in the area shown.
7.
Remove the rear trim panel by removing the four
clips and releasing the two hooks.
2 HOOKS
REAR TRIM
PANEL
4 CLIPS
RIGHT TRUNK SIDE
TRIM PANEL
CLIPS
(Turn the center pin
in a counterclockwise
direction to remove.)
TRUNK
WEATHERSTRIP
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 42446 (0908)
3 of 11
10. Remove the center console cover.
A/T Vehicle
M/T Vehicle
•
•
•
Remove the center console cover by removing the
three clips that fasten the center console cover.
Pull down on the shift boot, then loosen the
fastening nut by turning it counterclockwise.
Remove the shift knob by turning it
counterclockwise. Remove the fastening nut by
turning it clockwise.
CENTER
CONSOLE
COVER
3 CLIPS
SHIFT KNOB
FASTENING NUT
SHIFT BOOT
PARKING BRAKE LEVER
(Pull up completely.)
11. Open the center console lid, and remove the mat.
•
Remove the center console cover by removing
the three clips that fasten the center console
cover.
3 CLIPS
12. Remove the two self-tapping screws, two screws,
and two clips that fasten the center console, then
remove the center console.
CENTER
CONSOLE
COVER
MAT
SELF-TAPPING
SCREWS
2 SCREWS
2 CLIPS
CENTER
CONSOLE
LID
PARKING BRAKE LEVER
(Pull up completely.)
CENTER
CONSOLE
4 of 11
AII 42446 (0908)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
13. Turn the knob counterclockwise, release the two
clips and remove the driver's dashboard under
cover by lowering the cover and pulling it toward
you. Take care not to damage the clips.
15. Release the four clips, and remove the
passenger's dashboard under cover by pulling it
toward you. Take care not to damage the clips
and pins.
KNOB
(Turn counterclockwise.)
2 PINS
2 CLIPS
DRIVER’S DASHBOARD
UNDER COVER
14. Release the eight clips, and remove the driver's
dashboard lower cover by pulling it toward you.
Take care not to damage the clips.
4 CLIPS
PASSENGER’S
DASHBOARD UNDER
COVER
16. Release the two hooks and remove the lid above
the front console pocket.
FRONT CONSOLE
POCKET
LID
2 HOOKS
DASHBOARD
LOWER COVER
8 CLIPS
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 42446 (0908)
5 of 11
17. Remove the two bolts from the bottom of the
center panel.
Routing the Bus Cable
18. Release the ten retaining clips, and pull the center
panel toward you.
20. Route the bus cable along the vehicle harness
from the trunk side.
19. Unplug the right vehicle connectors, then remove
the center panel.
10 CLIPS
BUS CABLE
RIGHT REAR
SEATBACK
BOLTS
21. Return the right rear seatback, then remove the
clip securing the floor carpet. Turn over the floor
carpet.
22. Route the bus cable connector as shown.
FLOOR CARPET
Route
under the
floor
carpet.
BUS
CABLE
6 of 11
AII 42446 (0908)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
23. Route the bus cable forward to the right front
console frame along the vehicle harness.
26. Secure the bus cable to the vehicle harness with
five wire ties.
24. Route the bus cable connector to the dashboard
and out through the dash opening.
27. Using isopropyl alcohol on a shop towel, clean the
area where the cushion tape will attach. Attach the
bus cable to the floor panel with the two cushion
tapes in the area shown.
DASH OPENING
DASH OPENING
VEHICLE
HARNESS
VEHICLE
HARNESS
BUS CABLE
WIRE TIES
CUSHION
TAPES
BUS CABLE
25. Measure 300 mm from the end of the bus cable
connector, then secure the bus cable to the
vehicle harness with three wire ties.
BUS CABLE
CONNECTOR
With the vehicle bracket
Using the isopropyl alcohol on a shop towel, clean
the inside of the vehicle bracket where the
cushion tape attaches. Attach the cushion tape on
the vehicle bracket at the location shown.
CUSHION
TAPE
VEHICLE
BRACKET
300 mm
WIRE TIES
ATTACHMENT
LOCATION
BUS CABLE
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 42446 (0908)
7 of 11
28. Turn over the floor carpet, and attach the bus
cable to the floor panel with the three cushion
tapes in the areas shown.
Installing the CD Changer
30. Carefully unpack the CD changer.
29. Secure the bus cable to the vehicle harness with
the five wire ties in the areas shown.
CUSHION
TAPE
POSITION)
WIRE TIES
BUS CABLE
HORIZONTAL
VERTICAL
Turn over.
AFTER SETTING)
CUSHION
TAPES
CHANGER
KNOB
VEHICLE
HARNESS
31. The adjustment knobs have been set to the
vertical (V) position before shipping the CD
changer from the factory. Move the adjustment
knobs to the horizontal (H) position using a small
flat-tip screwdriver.
32. Position the CD changer brackets on the sides of
the CD changer, then install the four 4 x 8 mm
washer-screws.
2 WASHER-SCREWS
4 x 8 mm
CD
CHANGER
SIDE BRACKETS
8 of 11
AII 42446 (0908)
2 WASHER-SCREWS
4 x 8 mm
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
33. Position the CD changer on the CD changer
bracket, then install and tighten the four 6 mm
flange nuts.
35. In the trunk, slide the clip nut into position on the
rear seat panel through the hole in the panel. If
necessary, spread the clip nuts open with a small
flat-tip screwdriver.
4 FLANGE NUTS
36. Loosely install the washer-bolt to the rear seat
panel first. Then place the end of the CD changer
bracket between the seat panel and the clip nut
you just installed.
CD
CHANGER
WASHER-BOLT
CD CHANGER
BRACKET
CD
CHANGER
34. Wrap one EPT sealer around the bus cable
connector from the CD changer, then secure the
bus cable and connector to the CD changer
bracket with the two wire ties you just installed.
EPT SEALER
CD CHANGER
BUS CABLE
CONNECTOR
CD
CHANGER
CLIP NUT
CD CHANGER BRACKET
(Place the end of the
bracket between the
seat panel and clip nut
you just installed.)
WIRE TIES
CD CHANGER
BRACKET
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 42446 (0908)
9 of 11
37. Slide the two clip nuts onto the CD changer
brackets and rear shelf through the holes in the
parcel shelf, and align their holes as shown. Install
the two washer-bolts, and tighten them securely.
39. Fold the excess bus cable and secure the bus
cable to the holes of the rear seat panel with the
two wire ties with clip.
REAR SHELF
CD CHANGER
CLIP NUT
CD
CHANGER
BRACKET
CD
CHANGER
BRACKET
CLIP NUTS
BUS CABLE
Fold the excess
cables.
2 WIRE TIES WITH CLIP
RIGHT
SEAT PANEL
WASHER-BOLTS
38. Connect the bus cable connector to the CD
changer connector from the CD changer.
CD CHANGER
BUS CABLE
CONNECTOR
CD CHANGER
CONNECTOR
BUS CABLE
10 of 11
AII 42446 (0908)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
40. Plug the bus cable connector, vehicle 20-pin
connector (blue), and antenna lead into the rear of
the audio unit.
41. Connect the four vehicle connectors to the
center panel, and reinstall the center panel.
4 VEHICLE CONNECTORS
STANDARD AUDIO UNIT
CENTER PANEL
BUS CORD
CONNECTOR
VEHICLE 20-PIN
CONNECTOR
ANTENNA
LEAD
VEHICLE 20-PIN
CONNECTOR
ANTENNA
LEAD
BUS CABLE
BOLTS
(reused)
MULTI CONTROL CD TUNER UNIT
CD PLAYER
42. Check that all wire harnesses are routed
properly and that all connectors are plugged in.
BUS CABLE
43. Reconnect the negative cable to the battery.
44. Reset the clock and the radio station presets.
45. Check the operation of the CD changer as
described in the accessory user's information
manual.
POCKET
ANTENNA
LEAD
VEHICLE 20-PIN
CONNECTOR
46. Reinstall all removed parts. Be sure that all
retaining clips and tabs are secrely fastened.
47. Put the accessory user's information manual in
the glove box for your customer.
NAVIGATION HEAD UNIT
48. Initialize and test the front window auto up/down
function.
VEHICLE 20-PIN
CONNECTOR
ANTENNA
LEAD
BUS CABLE
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 42446 (0908)
11 of 11