Gaggenau VL051107 Owner Manual

Add to my manuals
15 Pages

advertisement

Gaggenau VL051107 Owner Manual | Manualzz

Operating and assembly instructions

VL 051-107

Automatically extendible hob ventilator

3

VL 051-107

Preface

1. Important notes

1.1 For your safety

1.2 Operating for the first time

1.3 About use

2. Structure and operating principle

2.1 Structure of the appliance

2.2 Control panel

2.3 Accessories

3. Operation

4. Cleaning and care

5. Maintenance

6. Assembly instructions

6.1 Technical data

6.2 Important notes

6.3 Electrical connection

6.4 Installation next to a gas hob

6.5 Installation

Page 3-4

Page 3

Page 4

Page 4

Page 5

Page 5

Page 5

Page 5

Page 6

Page 7-8

Page 9

Page 10-13

Page 10

Page 10

Page 11

Page 11

Page 12-13

1

Preface

With your new hob ventilator, working in the kitchen will be even more fun.

The appliance offers you the following advantages:

– Kitchen vapours and fats are sucked away directly where they arise.

– The advantages of a hob ventilator are combined with those of a single-point extractor.

To ensure that you will be able to use this appliance in all its diversity, read through the operating and assembly instructions conscientiously before operating it for the first time . The instructions contain important notes on use, installation and maintenance of the appliance.

On the following page you will find important notes on safety and operation. These will serve to ensure your personal safety and the lasting value of your appliance.

You will find notes on Page 4 that you ought to observe before operating the appliance for the first time .

The chapter entitled “Cleaning and care" will make sure that your appliance will stay operable and beautiful for a long time.

And now we wish you lots of fun with your new hob ventilator.

2

Fig. 1

1. Important notes

1.1 For your safety

Damaged appliances must not be operated.

The appliance must only be connected by an authorised specialist , paying attention to the relevant regulations of the power supply companies and the regional construction regulations.

Also observe the assembly instructions!

Connecting cables must not come into contact with hot cooking surfaces.

Hazardous or explosive substances and vapours must not be extracted!

The user is responsible for expert use and the perfect condition of the appliance.

Never operate the appliance without a grease filter .

Only ever operate the appliance under supervision . The appliance is intended solely for use in the household and must not be put to any other uses.

Do not place any objects on the appliance ; this will have a detrimental effect on functioning.

Do not place any objects under the swivel arm when it is extended. Make sure that there are no obstacles in the swivel and entry range.

Do not clean the appliance with a steam cleaning apparatus or with water pressure because this poses a risk of short-circuits.

Isolate the appliance from the mains during every maintenance operation . To do this, remove the mains plug or actuate the corresponding fuse. If the mains plug is not accessible, the appliance must be deenergised by means of the domestic installation fuse.

In the event of malfunctions, first of all check the household fuses. If the malfunction has nothing to do with the power supply, please contact your specialist dealer or your responsible Gaggenau after-sales service. Repairs must be carried out by authorised specialists, thus ensuring electrical safety.

After a power failure , the hob ventilator will not switch on automatically, but must be reset instead by any operator action.

When operated next to gas appliances, the swivel arm must be extended at least to the top edge of the pan as otherwise the flame of the gas burner will be impaired. Gas appliances may only be used next to a hob ventilator when pots and pans are placed on them! Please note that a wok must not be installed next to a hob ventilator.

No warranty claims can be lodged in the event of damage caused by failure to observe these instructions.

Caution!

Over-greased filters are a fire risk! Only ever deep-fry under the extractor under constant supervision. Pay attention to cleaning the grease filter on a regular basis.

Fire risk! It is not permitted to flambé meals next to a hob ventilator that is in operation.

You may only ever use a grill or a deep fryer at the same time as the hob ventilator if it is under constant supervision.

This will involve a fire risk!

When the ventilator is installed next to gas appliances, swivelling of the boom in the direction of the gas must be prevented by an additionally fitted pin (see assembly instructions).

Caution! The appliance may get very hot!

Risk of burns!

Technical modifications reserved.

3

This appliance is labelled in accordance with the European Directive 2002/96/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable.

Check the appliance for transport damage before installing it.

Never allow children to play with the appliance.

Do not let adults or children operate the appliance unsupervised:

– if they are mentally or physically unable to use the appliance safely and correctly

– if they don’t have the knowledge and experience to use the appliance safely and correctly.

1.2 Operating for the first time

Before operating the appliance for the first time, please pay attention to the following notes:

– Conscientiously read through the operating and assembly instructions before operating the appliance for the first time.

– The rating plate for this appliance is included with the instructions on a separate sheet. Store the rating plate in the same location as your operating and assembly instructions. You need the rating plate for possible damage and warranty cases.

– Remove the packaging from the appliance and dispose of it properly.

Pay attention to the fact that there are accessories in the packaging.

Keep packaging elements out of the reach of children!

– Thoroughly clean the appliance before using it for the first time. (see chapter entitled “Cleaning and care")

– Before operating the appliance for the first time, check that the mains connection is in proper working order.

1.3 About use

– Do not pour any liquids into the tub!

If liquid should have inadvertently penetrated into the tub, wipe it out immediately.

– If the swivel arm gets soiled during operation, clean it before moving it in.

4

2. Structure and operating principle

2.1 Structure of the appliance

1

2

3

1 Grease filter

2 Lid

3 Swivel arm

4 Tub

5 Control panel

4

5

Fig. 2

2.2 Control panel

6 “Height adjustment" control knob

7

Grease filter pilot lamp

8 “Power level" control knob with the positions

0, 1, 2, 3, after-running stage and grease filter indication

3

Fig. 3

6

2.3 Accessories

7 8

You can order the following special accessories:

VV 200-000: connecting trim

5

6

3. Operation

Fig. 4

Fig. 5

3

3

Switching on

– Turn the “Power level" control knob to the required position on the right.

The boom moves automatically to the frying position, and it can then be extended continuously up to its fully extended position (cooking position) by turning the “Height adjustment" knob.

You can also extend the boom to the required position before switching on the appliance.

In the cooking position (height 100-410 mm), the boom can be swivelled manually; its swivel radius depends on its height when extended.

If the swivel arm is extended without an output level having been set, as from the roasting position the connected fan module automatically runs at a basic level.

Switching off

– Turn the “Power level" control knob to the 0 position on the left.

– Turn the “Height adjustment" knob to the left to retract the boom. The boom turns automatically to its defined starting position in the trough.

After-running

– Turn the control knob to the left to the (Afterrunning) position.

The hob ventilator continues to run at stage 1 for

10 minutes.

– Turn the control knob to the 0 position if you wish to prematurely end the after-running time.

Holiday protection

– The appliance switches itself off four hours after the last operator action. It can be reset by any operator input.

4. Cleaning and care

Fig. 6

Caution:

Avoid sharp and caustic cleaning agents as well as brushes and abrasive cleaners.

Clean the stainless steel tub with mild rinsing detergent and apply stainless steel care agent to the metal surfaces using a soft cloth.

Only clean the switch panel with a soft cloth. Do not use any cleaning agent as it might be agressive to the inscription markings.

Grease filter cleaning

The grease filter indication symbol lights up on the operating panel after around 30 hours of operation.

Illumination of this symbol signals to you that the grease filters have to be cleaned.

You can clean the metal grease filters in a dishwasher at a maximum temperature of 65°C. To do this, place the grease filters in the dishwasher in such a way that it is cleaned completely.

Clean the the grease filter at least once a month.

Proceed as follows:

– Turn the “Height adjustment" control knob to the right to extend the boom slightly. By doing so, you can detach the cover easily.

– Detach the cover.

– Turn the two retaining wires up and remove the grease filter from the appliance.

– Turn the control knob to the position (grease filter indication). This resets the operating time.

Insert in the reverse order.

Caution!

Only clean the grease filter after the appliance has cooled down.

7

8

Swivel arm cleaning

If the swivel arm gets very dirty, it can be dismantled for cleaning. You can clean the swivel arm in a dishwasher at a maximum temperature of 65°C.

Proceed as follows:

– Turn the “Height adjustment" control knob to the right to extend the boom slightly. By doing so, you can detach the cover easily.

– Detach the cover.

– Turn up the two retaining clips and remove the grease filter from the appliance.

– Place the two included protective covers on the tube opening to make sure that no small parts will fall into the suction pipe.

– Using a suitable tool, undo the 3 cap nuts.

– Remove the protective cover.

Insert in the reverse order.

Caution!

Only clean the swivel arm after the appliance has cooled down.

5. Maintenance

First disconnect the appliance from the mains before carrying out any repairs.

In the event of malfunctions , first of all check the household fuses.

If the power supply is in proper working order, but the appliance is nevertheless not functioning, then please contact your specialist dealer or your responsible Gaggenau after-sales service. Specify the appliance type. To this end, have a look at the rating plate, which is included with the operating and assembly instructions.

Repairs must only be carried out by authorised specialists, thus ensuring the safety of the appliance. Improper tampering will render all warranty claims null and void.

9

6. Assembly instructions

6.1 Technical data

Rating: 260 W

Weight: 19 kg

A fan module is needed for suction extraction.

Technical modifications reserved.

6.2 Important notes

The appliance must only be connected by an authorised specialist . The specialist is responsible for perfect functioning of the appliance at its installation location. He must explain the operating principle of the appliance to the user with reference to the operating instructions. He must explain to the user how the appliance can be isolated from the mains whenever required.

The exhaust air can be routed into a ventilation shaft or directly into the open through the outside wall. Adequate incoming air must be ensured whenever the hob ventilator is operated in the exhaust air mode and firing systems dependent on a chimney are operated at the same time.

It is not allowed to pass the exhaust air into a flue or exhaust air chimney that is in operation or into a shaft that is linked to the heating basement. Consult the chimney sweep responsible for your district whenever you wish to pass the exhaust air into a chimney that is not in operation.

During the course of planning, a chimney sweep must be consulted if a room air-dependent hearth is operated in the same room as the one in which a hob ventilator is operated in the exhaust air mode.

Adequate incoming air must be ensured. The applicable construction and safety regulations must be observed.

Adequate incoming air must be ensured if a wood, coal, gas or oil heater or an open hearth is operated in the same room as the one in which the wall hood is installed.

Adequate ventilation of the room must be ensured whenever a hob ventilator is operated simultaneously with devices that are operated with non-electrical energy. Official regulations must be observed with regard to removal of the exhaust air.

The applicable regulations of the power supply companies and the regional construction regulations must be observed when installing the hob ventilator.

Safe operation is possible whenever the partial vacuum in the place where the firing equipment is installed does not exceed 4 Pa (0.04 mbar). This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or other technical means.

Flexible aluminium pipes , corrosion-protected sheet metal pipes and exhaust air pipes whose material conforms to fire B1 in accordance with

DIN 4102 can be used. Exhaust air pipes should have a nominal diameter of 150 mm.

The lateral distance from the appliance installed next to it must amount to 8 mm.

If two Vario appliances are used, the hob ventilator must be installed between the appliances. If

4-plate hobs are used, it is recommended to place two ventilation devices to the left and right of the hob. Owing to the high air output, an adequate supply of air is required.

To prevent the ingress of water , e.g. condensate or rain water from an uncovered exhaust air shaft, our condensate separator RV 060-150 must be installed in the exhaust air line. The condensate separator must still be acciessible after installation.

10

6.3 Electrical connection

Pay attention to the rating plate data.

The mains connecting cable must at least correspond to the type H 05 VV-F G 0,75.

After installation, plug the connecting cable plug in an accessible socket. If the plug can no longer be removed after installation, isolation of all poles from the mains must be ensured by means of an accessible isolator with a contact spacing of at least

3 mm.

6.4 Installation next to a gas hob

Pay attention to the following notes if you wish to install a gas range next to the hob ventilator.

– A locking bolt must be installed in the hob ventilator to prevent the boom from swivelling over the gas range.

– Extend the unit.

– Position the swivel arm in the centre.

– Open the flap on the rear.

– Fit a pin (accessory) in the collar of the accessible mounting ring (black plastic part). Fit the pin on the side opposite to the one where the boom is no longer to swivel.

– Close the flap.

When operated next to gas appliances, the swivel arm must be extended at least to the top edge of the pan as otherwise the flame of the gas burner will be impaired.

VL 051-107 /01 FD xxxx xxxxxx

AC 220-240V / 50Hz max 260W xxxxxxxx

11

6.5 Installation

413

142

60

Extensi on heig

410 ht

Swivel range

180

°

8,5

710

510

490

Rec ess dept h

205

170

Fig. 7

250

460

Rec

156 ess

wid th

The hob ventilator can be installed next to one or between two built-in Vario appliances.

Choose the suitable connection variant (see

Page 13) before beginning with installation.

– Produce the recess for the appliance. Proceed as indicated on the installation sketch and the dimension table (Fig. 7). When installing several

Vario appliances at the same time, please pay attention to the dimensions specified in the type list. Important: The angle between the cut surface and the worktop must amount to 90°.

– Mark the centre of the recess exactly. Secure the securing rail in the recess at the rear with the included wood screws. Make sure that the lugs of the securing rail lie on the worktop and that the centre marking of the securing rail is precisely flush with the centre marking on the worktop.

(Fig. 8) When installed in a stone worktop, the securing rail must be adhered with a suitable adhesive.

– Make sure that the securing rail is fitted at a right angle to the surface of the worktop.

– Remove the protective film from the included sealing tape and stick the sealing tape onto the edge of the worktop so that the edge of the appliance when it is installed halves the sealing tape. The ends must not overlap.

– Define connection to the fan module before finally lowering the appliance into the worktop.

Before sawing out the base plate, check whether the depth of the base area is sufficient for the fan module.

12

Fig. 8

min. 900

156

50

490

Fig. 9 min.

600 min.

900 min.

560

500

195

365

872

245 min.

900 min.

900 min.

600

AR 0

30-12

5 min.

560

Fig. 10

GB

031

Worktop height ≥ 90 cm, variable position of the fan module

– Saw out the base plate in the built-in cabinet for the fan module.

– Place the fan module in the base cabinet.

Refer to the operating instructions of the fan module for details of how to install it.

– Using a flexible aluminium pipe (DN 125), connect the pipe connection piece to the fan module.

– Now lower the hob ventilator into the worktop.

Make sure that the engaging lugs on the appliance lie exactly on the clamping springs.

Press the appliance firmly into the worktop.

The engaging lugs on the appliance “snap" into the clamping springs.

– At the front, fix the hob clamping element onto the worktop from below until the appliance is pressed on evenly (Fig. 11). If the worktop is less than 36 mm thick, place the hob clamping element under it.

– Cut off protruding sealing tape.

Fig. 11

13

GAGGENAU HAUSGERÄTE GMBH

CARL-WERY-STR. 34 · D - 81739 MÜNCHEN

Y (0 89) 45 90-03

FAX (0 89) 45 90 - 23 47 www.gaggenau.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement