Wing Span:86.6in/2200mm; Flying Weight:6000g;
Wing Area:94sq.dm;
Radio:6Channel 6Servos;
Length:82.7in/2100mm;
Engine:50CC Gas
CAUTION : this plane is not a toy and should be kept away
children under 16 years of age! Before use , please carefully read
this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children’s reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
P.1
RUDDER AND TAIL WHEEL
●Make sure to apply Vaseline to
the rudder hinges to prevent the
epoxy from getting in to the joint.
●Make sure to allow room for
epoxy to penetrate the hinges.
Carefully slide the rudder onto
each hinge and against the trailing
edge of the fin.Wipe away excess
epoxy with alcohol wetted wipes.
●Ensure there is no gap
between fin and rudder.
Install the rudder servo in the
fuselage that prepared by factory.
Feed the rudder cable through the
cable exit tube in the tail of the
fuse toward the front of the fuse.
Repeat on other side.
Push
rods
Adjust rudder pull-pull cables
to desied tension by screwing in
or out on the threaded couplers
and or ball links.Make all adjustments with the rudder servos still
powered up and centered,and the
rudder still taped in the neutral
position.
Rudder
servo arm
P.2
●Ensure the servo doesn't bind
at center or at either end point.
Drill holes in the hardwood tail
wheel mount and install the blind
nut through the opening in the
rear of the fuse.
Install the mounting screw for the
tail wheel.
●Ensure it has been totally
screwed into the blind nuts.
Install the hatch over the opening in the rear of the stabilizer with 4 screws.
STABILIZER AND ELEVATOR
Mount the elevator onto the stab
making sure you use Vaseline in
the hinge points so the glue will
not stick the hinge shut.
Install the control horns in place
for the elevator horn before sliding
the stab in place.
Screw the threaded pushrod and
swivel in place onto the elevator
horn.Plug in a 24"servo wire
extension and use a securing clip
provided to make sure they don't
come unplugged in flight.
P.3
Attach the servo extension wire
using foam wire holding brackes
or zip ties to the formers along
the sides of the fuse so they
can't interfere with the rudder
control cables.
Mount the servo arm on to the
elevator push rod before installing
it on the servo so you can tighten
the nylon insert locking nut to the
mounting screw.
Slide the stab on to the alumium
tube and attach to fuse using the
bolts provided.
P.4
●Make sure the bolts has been
totally screwed into the blind nuts.
Install the servo arm to the servo
after making sure the elevator is
level with the stab with the servo
is in dead center.Tape the
elevator in place using blue
painter's masking tape.
Bolt on tabs for
stabs
MAIN WINGS
Install the aileron horns in place
with AB glue.Align the holes in the
horns .Install the servo after
pulling the servo extention wire
in the wing.Install the servo arm
on the servo and loctitle it in place
on the mount screw.Install the
pushrod and control horn.
AB
AB
●Check for movement and center
on the servo for the aileron to be
in a level resting position.
●Check to make sure you have
the servos in a reverse manner
so ailerons with work properly.
P.5
Find out the holes in each sides
of fuselage,then remove the
covering.Insert the carbon joiner
in place,then put on wings.
●Check to make sure you have
the carbon in a right length in the
wings.
Plastic
bolt
Mounting the wings with plastic
bolts on both sides.
MAIN LANDING GEAR
Gather the wheels,axles and
collars as shown.
Install the main landing gear with
the bolts provided and use blind
nuts already installed and use
blue Loctite on the mounting bolts.
●Bottom View
P.6
Permanently tighten the axle to
the gear strut by wrenches.
Install wheel pants with two
mounting bolts.
Wheel pants take a lot of abuse,
mount securely!
The finished photo as shown.
P.7
ENGINE
Measure the length of the engine
from the firewall mounts to the
prop thrust washer for the proper
distance allowing 1/4" to 1/2" from
the dege of the cowl.
Move if needed.
Draw the engine ecnter line and
thrust line darker with a ball point.
Note the 2 degree right thrust built
in to the firewall.
The cowl is already built with this
offset as well.
Use the drill template if you are
going to use a DA 50 or measure
your engines mounting location.
Remember the engine is mounted
inverted.
P.8
Determine where the throttle arm
push rod is going to the firewall
and drill a hole.If you are going to
use a Nyrod,then make the hole
the same size as the outsider
red tube.
muffler mount and a support in the
front of the muffler made of
plywood using some silicon tubing
for insulation form the heat using
glue.
Cut off the covering for the
canister muffler along the edge.
Carefully insert the muffler into the
prepared hole.
In case of break the wooden
fuselage.
FUEL TANK
P.9
Velcro tank straps
over foam.
Install the fuel tank mounting
ties under the fuel tank floor.
Install the battery,receiver and
switch in place as shown.
CANOPY
Slide the rubber backed washers
on the hatch mounting bolts and
insert bolts through the hatch
mounting holes and into the fuse
blind nuts.Tighten snugly but do
not over tighten and crush the
hatch or the fuse sides.
P.10
COWLING
Mount the cowl using the cowl
mounting screws and rubber
backed washers.the rubber
backed washers are to prevent
the fiberglass cowl from cracking
from normal engine vibration.
CG POSITION & CONTROL THROWS
6.14in
156mm
6.14in
P.11
THE FINISHED PHOTO
Another scheme for choice.
Another scheme for choice
Flight Model MFG CO.,LTD
ADD:No.10,Fu Ning Street,Xian Xi Industrial,Chang An Town,Dong
Guan City,Guang Dong Province,China
Tel: +86-769-85070618
Fax: +86-769-85091868
E-mail:info@flight-model.com
Web: http:www.flight-model.com
http://flight-model.preview.alibaba.com/
P.12
P.13
P.14
P.15
.
P.16
P.17
P.18
.
P.19
P.20
P.21
P.22