Contents in the Box
Welcome to
SMART WIFI
INDOOR SPRINKLER TIMER
Scan for full
User Manual
bhyve.orbitonline.com
Quick
Start
Guide
Compatible with other B-hyve products
The B-hyve™ App
Wi-Fi Indoor Sprinkler Timer
Transformer
Screwdriver
Quick Start Guide
Mounting Screws and Anchors
Conduit Cover
FCC and IC Statement
Déclaration de FCC et l’IC
This device complies with Part 15 of the FCC Rules and Industry Canada
license exempt RSS standards. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
FCC Warning: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device meets the FCC and IC requirements for RF exposure in
public or controlled environments. The end user is advised to maintain
a distance of 20 cm from the controller and any personnel to ensure
compliance with RF exposure regulations.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil est conforme à la section 15 de la Règlementation de la FCC
et la norme RSS d’Industry Canada.
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet
appareil ne doit pas causer d’interférences nuisibles, et (2) cet appareil
doit tolérer toutes les interférences, dont les interférences pouvant
causer un fonctionnement non désiré. Cet appareil numérique de classe
B est conforme à la norme canadienne ICES-003.
Remarque: cet appareil été testé et déclaré conforme aux limites
d’exposition pour les appareils numériques de classe B, selon la section
15 de la Règlementation de la FCC. Ces limites sont conçus pour fournir
une protection raisonnable contre les interférences nuisibles dans une
installation résidentielle. Cet appareil produit, utilise et peut émettre
de l’énergie radio fréquence et, si elle n’est pas installée et utilisée
conformément aux instructions, peut causer des interférences nuisibles
aux communications radio. Cependant, il n’est pas garantie que des
interférences ne se produisent pas dans une installation particulière.
Si cet appareil cause des interférences gênantes à la réception d’un
signal radio ou de télévision, ce qui peut être déterminé en allumant et
en éteignant l’appareil, l’utilisateur peut corriger les interférences en
suivants une des mesures suivantes :
• Réorientez ou repositionnez l’antenne de réception.
• Augmentez la distance entre l’appareil et le récepteur.
• Branchez l’appareil dans une prise sur un circuit différent du circuit sur
lequel le récepteur est branché.
• Consulter le revendeur ou un technicien radio/TV expérimenté pour
obtenir de l’aide.
Cet appareil est conforme aux exigences de la FCC et de l’IC concernant
l’exposition aux ondes dans un environnement public ou contrôlé. Il
est conseillé à l’utilisateur final de maintenir une distance de 20 cm du
contrôleur pour assurer la conformité aux réglementations d’exposition
RF. Information de conformité pour le Canada
Install the B-hyve™ app on
your smart device
You will need a smart device to connect the
timer to Wi-Fi.
Timer Connected Symbol
Specifications
Note: The app will guide you through initial
set up of your sprinkler timer. In addition,
there are help icons throughout the app
with more information and useful tips.
Weather/Temp.
Transformer ratings:
Input:
Australia—240V AC 50/60Hz 23W
Europe—230V AC 50/60Hz 23W
USA—120V AC 60Hz 23W
Output:
24V 750 mA
Timer ratings:
Input/Output:
AUS & EU—26V AC 750 mA 50/60 Cycle
USA—24V AC 750 mA 60Hz
Help
If the app and the website don’t have what
you’re looking for, please call our technical
support line before returning this sprinkler
timer to the store.
1-800-488-6156 or 1-801-299-5555
www.orbitonline.com | bhyve.orbitonline.com
Acts as a hub forother
B-hyve™ products
Timer Temperature Operating Range:
Operating: 32-158° F (0–70° C)
Storage & transport: -4–176° F (-20–80° C)
Timer Humidity Operating Range:
Operating: 0–80%
Storage & transport: 0–90%
Running Status/Messaging
Stop Watering
Rain Delay
Next Zone
Calendar
Programs
Remote Control
or Home Button
Settings
Altitude:
6,500' (2,000 meters)
Installation Class II
Over Voltage Category II
This timer works with any standard 24V
irrigation solenoid.
The internal fuse is non-replaceable.
Zone List
57915-50 rB
Timer Installation
Select a location
Choose a location near power and away
from direct sunlight, if possible. Make sure
to leave room for the timer door to open
completely.
This location should also have a good Wi-Fi
signal. You can check this using a smart
phone. (Find a location that has a minimum
of two bars)
Connect Valve Wires
Minimum Signal
Keyhole
1/8" (3 mm)
Note: If replacing a timer, it is helpful
to take a photo of the wires before you
remove them from the old timer.
Timer Installation–Connecting to Wi-Fi
Plug in your Orbit® B-hyve™ timer
Once your B-hyve™ timer is plugged into
the power source, it will automatically look
to pair with your smart device. The
will begin to blink blue. This indicates that
your timer is ready to pair with your smart
device. Ensure that your smart device has
Bluetooth® turned on.
Prepare wire
Strip 1/2" (13 mm) of insulation from each
wire.
Connect wires
Attach one wire from each valve to a
“Common” (COM) wire and the other
wires to a numbered terminal (only one
wire per terminal.)
Connect to your Orbit® B-hyve™ timer Open your B-hyve™ app, create an account
or login, and follow the step-by-step
process to add and set up your device. The
B-hyve™ app will connect to your device
and you will, then, be guided to connect to
your home Wi-Fi network.
No. 8 Screw
Mount the timer
Install a screw (included) into the wall.
Use the expanding anchors (included) for
plaster, masonry or drywall installations.
Hang the timer on the installed screw using
the keyhole slot. Level the timer and use
the second screw in one of the preformed
mounting holes to secure the timer.
Wall
Loosen Screw
Pre-formed
Mounting Holes
Programming and Operation
Note: If you do not see your network name
in the list, tap the refresh button in the
app. If your network name still does not
appear, tap “Advanced” in the app and
enter your network name and password.
This device will only connect through 2.4
GHz Wi-Fi networks. 5.0 GHz networks
are not supported and will not appear in
your app.
Tighten Screw
Note: Your programmed schedules are
stored both in the app and on the timer.
Watering will continue, if Wi-Fi connection
is lost.
Manual Operation
All programming and full functionality of
the timer are available in the B-hyve™ app.
If you have the need, there are some
basic operations you can perform directly
at your timer.
Connect to your Wi-Fi network
Select your network from the list and enter
the password for the network to connect
your timer to your Wi-Fi signal. When
will illuminate solid
connected, the
white indicating a successful pairing.
Strip Wire
Push In
Programming the timer
The app has help screens and video
to assist you with Wi-Fi connections,
programming, smart watering and other
general questions you may have.
Function
Button Press
MANUAL WATERING
Hold until (water ALL stations) appears, then release.
Quickly press again until desired station appears.
Default watering is 10 min. per station.
CANCEL STATION
FOR OPTIMUM TIMER
PERFORMANCE, CONNECT
TO WIFI TO RECEIVE THE
LATEST TIMER UPDATES.
RAIN DELAY
ON/OFF
HARD RESET
Press
once to cancel current station.
Set in app;
Hold
blinks yellow and appears.
for 10 sec. until
Quickly press
turns white.
5 times.