TD-3200 H1 系列快速安装指引 中性 英文 第一界面

Network Video Recorder
Quick Start Guide
4. Rear Panel Instruction
The interfaces of the rear panel are for reference only.
After you finish adding IP cameras, you can see the live images through the
monitor of the NVR. The following will mainly introduce how to add the IP
cameras via LAN/WAN.
►LAN
1. Notes
① Set the network of the NVR. Go to Start → Settings → Network →TCP/IPv4.
Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP
in both the NVR and the router.
● Please read this instruction carefully for correct use of the product and
preserve it for reference purposes.
② Go to Start → Settings → Network → Port. Input HTTP port (the default
value is 80), server port (the default port is 6036).
● All the examples and pictures used here are for reference only.
● There may be several technically incorrect places or printing errors in
this manual. The updates will be added into the new version of this manual.
The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
③ Click “Apply” to save the settings.
TCP/IPv4
Port
192 . 168 .
② The device will boot and the power indicator will display blue.
② Put the screws into the HDD.
Go to “Main Menu” and then select “Shutdown” icon. This will bring up a
shutdown window. The device will shut down by clicking “OK” button.
Then disconnect the power.
2
0 .
0
192 . 168 .
1 .
1
192 . 168 .
Alternate DNS
0
.
0
.
1 .
1
0 .
0
④ Go to Start → Settings → Camera → Add Camera. The NVR will automatically
refresh the cameras searched. The IPC which supports the Onvif protocol may
be added manually. If the IPC searched is not in the same local network as the
NVR, you should select the device and click to modify the IP address.
Add Camera
Quickly Add
You must configure the wizard if you start the NVR for the first time. You can
skip the settings of wizard next time. The default username is admin and the
password is set by yourself when you configure the wizard for the first time.
Click “Start” and select “Login”. This will take you to see a login box. Input
default username and password you set and you can see the live image.
Manually Add
IP Address
Port
Protocol
Model
1
192.168.1.20
80
255.255.255.0
XXX
XXX
3.4.2
2
192.168.1.38
80
255.255.255.0
XXX
XXX
3.4.2
3
192.168.2.45
80
255.255.255.0
XXX
XXX
4.0.0.1.beta1
No.
Password
Version
Remain Bandwidth: 108 / 120 Mb
Default Password
Add
Cancel
Edit IP Camera
admin
192 .168 . 1 . 45
Subnet Mask
255 . 255 . 255 . 0
Port
Log In Automatically
CE :98 :23 :75 :35 :22
IP Address
Gateway
Enter Password
Display Password
Subnet Mask
Edit
Selected: 1/3
Mac Address
Username
④ Turn over the machine and secure
the HDD with the screws.
1 .
.
Login
③ Place the HDD onto the bottom
of the case.
0
③ A wizard window will pop up.
6. Login
① Loosen the screws to open the cover.
.
Obatin DNS server address automatically
Preferred DNS
►Shutdown
This series of the product supports 1 SATA hard drive. Please make sure that
the device is powered off before the installation. The pictures of the installation
are only for reference, please take the real object as the standard.
0
Gateway
① Connect the monitor and the power.
3. HDD Installation
Network Status
Obtain an IP address automatically
IP Address
►Startup
Please check the device and the accessories after getting the device. If there are
any damages, shortages or defects, please contact your dealer immediately.
NAT
Ethernet Port 1 ( Online )
5. Startup & Shutdown
Subnet Mask
2. Packing Check
UPnP
E-mail
DDNS
IP Address Settings
Username
192 .168 . 1 . 1
9008
admin
Password
OK
Edit Security Question
⑤ Connect the power and data cables.
⑥ Install the cover back and fix it.
7. Network Configuration
Login
Cancel
Cancel
⑤ Checkmark the device you want to add and then click “Add” button.The
NVR will automatically refresh the cameras and return to “ Edit Camera”
interface.
“Online” status means connecting the device successfully and you will
see the live image. You may select the added device and click button to
modify channel, IP address, ect.
TCP/IPv4
Port
E-mail
UPnP
NAT
Network Status
Enable
Map Type
Edit Camera
DDNS
UPnP
Auto
Edit Camera Group
External Port
Port Type
External Address
Port
UPnP Status
80
Valid UPnP
Edit
Search Camera
80
183.17.254.19
Server Port
6036
183.17.254.19
RTSP Port
554
HTTP Port
Port
Status
Protocol
Model
1
IP Channel 4
192.168.1.20
9008
Online
XXX
XXX
2
IP Channel 3
192.168.1.38
9008
Offline
XXX
XXX
3
IP Channel 5
192.168.1.45
9008
Online
XXX
XXX
No.
Camera Name
IP Address
Preview
Edit
Delete
6036
Valid UPnP
554
Invalid UPnP
Refresh
Apply
Device Serial Number: Click
on the menu bar at the bottom of the live
interface to check the serial number or go to Start → Settings → Network →
Network Status to check the serial number of the NVR).
User Name: The username of the NVR. The default username is admin.
Password: The password of the NVR. The password is set by yourself when
you configure the wizard for the first time.
10. Manual Recording
Before recording, please install and format a HDD. In the live interface
9. NAT
you can see the menu toolbar. Click
►NAT Settings
it again to stop recording. You can also click
the recording.
Remain Bandwidth: 85 / 120 Mb
IP Camera Name
IP Channel 5
IP Address
192 .168 . 1 . 58
Protocol
② Go to Start → Settings → Network → TCP/IPv4. You can obtain the IP
address, subnet mask and gateway automatically. You can also manually enter
them according to the actual network situation. Please make sure the network
segment is the same as that of the network which is used.
9008
XXX
Model
XXX
Username
admin
Password
Display Password
Test
to check the status of
① The NVR shall be powered on and connected to the network.
Edit IP Camera
Port
button to start recording. Click
OK
Cancel
③ Set the preferred or alternative DNS Server. Click “Apply” to save the
parameters.
►Instant playback
④ Go to Start → Settings → Network → NAT tab. Enable NAT and select
the NAT Server (The default NAT Server is nat.autonat.com). Click
“Apply” to save the parameters.
Click “Instant Playback” in the right-click menu of the camera’s preview
window to select or drag the playback progress bar to change the playback
time to play back the record.
►WAN
① Set the network of the NVR. Go to Start → Settings → Network → TCP/IPv4.
Input static IP address or enable PPPoE and then input the user name and password
received from your ISP.
② Go to Start → Settings → Camera. Click “Add Camera” or
behind the
column of the search camera and select “Manually Add” to add the IP cameras.
Input IP address, server port, username and password of the IP camera. The IP
camera must be connected over WAN. And here the IP address of the IP camera
must be a WAN IP address.
8. UPnP
You can use the UPnP function to enable the fast connection of the device to
WAN via a router without port mapping.
① Go to Start → Settings → Network → UPnP, and enable UPnP and then
click “Apply” button to save.
11. Playback
TCP/IPv4
Port
DDNS
E-mail
UPnP
NAT
Network Status
Click
on the tool bar at the bottom of the live preview interface or click
Start → Playback to go to the playback interface as shown below. You can also
add the playback cameras manually. Click in the playback window to pop
up the “Add Camera” window. Check the cameras in the window and then click
“Add” to add playback camera. The record files of the added playback camera
will be played in the playback interface.
NAT
Enable
NAT Server
►General playback
nat.autonat.com
Apply
►NAT Access
After finishing the NAT settings, you can input http://www.autonat.com/n9000
in the IE address bar and then press enter to go to the following interface. If
you are the first time to access the NAT, you shall download and install the
ActiveX according to the popup tips. After installing ActiveX successfully,
it will pop the login box.
Enter device serial number
② Enable the UPnP function in the router.
③ Click “Refresh” button to refresh the UPnP status. If the UPnP status were
still “Invalid UPnP” after refreshing it for several times, the port would be wrong.
Please change the mapping type to “Manual” and then click
to modify the
port until the UPnP status turns to “valid UPnP”.
Enter Password
Enter Password
Login
450041000747 A0