roboslul3 - Chamberlain

OWNER’S
MANUAL
ROBOSLUL3™
V E H I C U L A R S L I D E G AT E O P E R AT O R
THE ROBOSLUL3™ IS FOR USE ON VEHICULAR PASSAGE GATES ONLY
AND NOT INTENDED FOR USE ON PEDESTRIAN PASSAGE GATES.
TA B L E O F C O N T E N T S
SPECIFICATIONS AND WARNINGS
WARNING
Overview and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Model Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Safety Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Suggested Entrapment Protection Device Locations . . . . . . . .5-6
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Mechanical
WARNING
Electrical
INSTALLATION
CAUTION
Installation Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Safety Catch Rollers and Gate Rail Stops . . . . . . . . . . . . . . . . . .9
Mounting Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Chain Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Control Board Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Surge Suppressor Terminal Connections . . . . . . . . . . . . . . . . . .12
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
WIRING
Earth Ground Rod Installation . . . . . . . . . . . . . . . . . . . . . . . . . .13
DC Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Linking Master/Second Operators . . . . . . . . . . . . . . . . . . . . . . .15
Entrapment Protection Devices (Contact Sensors) . . . . . . . . . .16
Entrapment Protection Devices (Non-Contact Sensors) . . . . . .17
3-Button Control Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Maglock/Solenoid Connection . . . . . . . . . . . . . . . . . . . . . . . . . .19
Plug-In Loop Detector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . .20
12 VDC External Loop Detector Wiring . . . . . . . . . . . . . . . . . . .21
IMPORTANT NOTE
• BEFORE attempting to install, operate or maintain the
operator, you must read and fully understand this manual and
follow all safety instructions.
• DO NOT attempt repair or service of your residential gate
operator unless you are an Authorized Service Technician.
ADJUSTMENTS
Set Gate Opening Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Limit Switch Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Setting the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Radio Receiver Programming . . . . . . . . . . . . . . . . . . . . . . .24-25
Adjusting Reversing Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . .26
MAINTENANCE
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
OPERATION
Built-In Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Audio Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Emergency Manual Release . . . . . . . . . . . . . . .30
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . .34-35
REPAIR PARTS
Repair Part Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
How to Order Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Part Names and Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
INSTALLATION CHECKLIST . . . . . . . . . . . . . . . . . . . . . . .39
WARRANTY POLICY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
1
Specifications and Warnings
OVERVIEW
Battery Connection Page 14
Radio Receiver Pages 24 and 25
12 VDC - 7.2 Amp
Battery Page 14
Limit Switch Assembly Page 22
Surge Suppressor Terminal
Page 12
DC Motor
Robo UL Control Board
Page 11
UL Alarm Page 29
Idler Pulley
Electronic Access Panel
Gate Chain
Electronic Box
Drive Sprocket
Gear Reducer 40-30:1
Built-In Reset Button Page 28
EMERGENCY RELEASE Page 30
Chassis
Battery Manual
M
S SD
pe S
ci B
fi a
ca tt
ti ery
on
s
18 Vac Transformer Power
Wire Connector Page 14
AIN
4
1
2 Warning
Placards
Gate Chain
C
Warranty
Card
nt
y
25 F
25 F
eet
CH
ar
d
18 Vac
Transformer
ra
41
AIN 1
CH eet CHAIN 4
ar
t
W
ee
F
25
Gate Attachment Accessories
S P E C I F I C AT I O N S
Gate Speed
Maximum Gate Length
Maximum Gate Weight
Motor
Maximum Cycles
–
–
–
–
–
–
–
AC Power Supply
–
AC Power Supply Wire –
DC Power Supply
Solar Power
–
–
11 inches per second.
20 feet.
800 pounds.
DC, 12 V, 1/8 HP.
70 cycles per day with a Plug-In Transformer.
Solar power cycles per day varies, Contact Chamberlain Elite for more Information.
Battery back-up cycles (50 cycles total at maximum weight with factory battery, NO AC or solar
panel connected).
18 Vac 2.0 Amp Plug-In Transformer.
14 gauge or greater landscape lighting cable rated for direct burial and 300 watts at maximum length
of 1000 ft. Not Provided.
Battery, 12 volt-7.2 amp, main power.
Optional (Part # SOLAR3).
2
U L 3 2 5 M O D E L C L A S S I F I C AT I O N S
The ROBOSLUL3™ is intended for use in vehicular slide gate applications:
Class I – Residential vehicular gate operator
A vehicular gate operator (or system) intended for use in a home of one-to four single family
dwellings, or a garage or parking area associated therewith.
Class II – Commercial/General access vehicular gate operator
A vehicular gate operator (or system) intended for use in a commercial location or building such as a
multi-family housing unit (five or more single family units) hotel, garage, retail store or other building
servicing the general public.
Class III – industrial/limited access vehicular gate operator
A vehicular gate operator (or system) intended for use in a industrial location or building such as a
factory or loading dock area or other location not intended to service the general public.
Class IV – Restricted access vehicular gate operator
A vehicular gate operator (or system) intended for use in a guarded industrial location or building such
as an airport security area or other restricted access locations not servicing the general public, in
which unauthorized access is prevented via supervision by security personnel.
UL325 ENTRAPMENT PROTECTION REQUIREMENTS
This chart illustrates the entrapment protection requirements for each of the four UL325 classes.
In order to complete a proper installation you must satisfy the
entrapment protection chart shown. That means that the installation
GATE OPERATOR ENTRAPMENT PROTECTION
must have one primary means of entrapment protection and one
independent secondary means of entrapment protection. Both primary
Swing & Gate Barrier
UL325 Slide Gate Operator
and secondary entrapment protection methods must be designed,
(Arm)
Operator
Installation
arranged or configured to protect against entrapments in both the
Primary
Secondary
Primary
Secondary
Classification
open and close directions of gate travel.
Type
Type
Type
Type
For Example: For a gate system that is installed on a single-family
Class I
B1, B2
A, B1, C,
A
A or C
residence (UL325 Class I) you must provide the following: As your
Class II
or D
or D, B2
primary type of entrapment protection you must provide
• Type A - inherent (built into the operator) entrapment sensing and at
A, B1, B2
A, B1,
A, B1, C
Class III
D or E
least one of the following as your secondary entrapment protection:
D or E
or B2
or C
• Type B1 - Non-contact sensors such as photo-eyes,
A, B1, B2 A, B1, B2,
A, B1, C
A, B1, C,
• Type B2 - Contact sensors such as gate edges or
Class IV
D or E
or D
or D
D or E
• Type D - Constant pressure control.
• Type E - Built-in audio alarm.
Intended for Limited Duty Operation
NOTE: UL requires that all installations must have warning signs placed in plain view on both sides of the gate to warn pedestrians of
the dangers of motorized gate systems.
3
S A F ET Y I N S TA L L AT I O N I N F O R M AT I O N
1. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage class of the gate.
b. All openings of a horizontal swing gate are guarded or screened from the bottom of the gate to a minimum of
4' (1.2 m) above the ground to prevent a 2 1/4" (6 cm) diameter sphere from passing through the openings anywhere in the
gate, and in that portion of the adjacent fence that the gate covers in the open position.
c. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers.
2. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a
separate access opening.
3. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent
structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into
public access areas.
4. The gate must be properly installed and work freely in both directions prior to the installation of the gate
operator.
5. Controls must be far enough from the gate so that the user is prevented from coming in contact with the
gate while operating the controls.
6. Controls intended to be used to reset an operator after 2 sequential activations of the entrapment protection
device or devices must be located in the line of sight of the gate, or easily accessible controls shall have a
security feature to prevent unauthorized use.
7. All warning signs must be installed where visible, on each side of the gate.
8. For a gate operator utilizing a non-contact sensor:
a. Reference owner’s manual regarding placement of non-contact sensor for each type of application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still
moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter
reachable by a moving gate or barrier.
9. For a gate operator utilizing a contact sensor such as an edge sensor:
a. A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate
operator is not subject to mechanical damage.
b. A wireless contact sensor such as the one that transmits radio frequency (RF) signals to the gate operator for entrapment
protection functions shall be located where the transmission of the signals are not obstructed or impeded by building
structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended end-use
conditions.
c. One or more contact sensors shall be located at the leading edge, trailing edge and post mounted both inside and outside of a
vehicular horizontal slide gate.
d. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
e. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom
edge of a swing gate is greater than 6" (15 cm) above the ground at any point in its arc of travel, one or more contact sensors
shall be located on the bottom edge.
4
S U G G E S T E D E N T R A P M E N T P R O T E C T I O N D E V I C E L O C AT I O N S
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
Non-Contact Sensors (Photo Electric Sensors)
Install photo electric sensors to protect against any entrapment
or safety conditions encountered in your gate application.
See page 17.
er
g
an
D
le
t
en Cyc
pmEN
a
r
P
t
En or O
f
rty
ide
ts
Ou
pe
Pro
ty
afe
S
ideLoop
s
t
Ou
Safety loops allows the gate to stay open
when vehicles are obstructing the gate path.
Suggested for vehicles 14 feet or longer.
See pages 20 and 21.
ety
f
a
S
de Loop
i
s
In
rty
ide
Ins
pe
Pro
Gate Rail Stops For safety
reasons, physical stops MUST
be installed on both ends of
the gate rail prior to
installation of the gate
operator. This will assure that
the gate does not derail while
opening or closing fully.
See pages 9.
rty
pe
Pro
r
ge e
n
l
a
e
ettyy D Cyc
tsid
f
u
a
O
e aS foep OSE
d
i
S
ts o L
Ou oLr C
f
ety
f
a
S
de Loop
i
s
In
rty
ide
Ins
5
pe
Pro
S U G G E S T E D E N T R A P M E N T P R O T E C T I O N D E V I C E L O C AT I O N S
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
Contact Sensors (Edge Sensors)
Install edge sensors to protect against any entrapment or
safety conditions encountered in your gate application.
See page 16.
Edge sensor for open cycle on wall.
Edge sensor for open cycle on gate.
Edge sensor for open cycle on wall.
Edge sensor for
close cycle on wall.
e
tsid
Ou
y
ert
p
Pro
Edge sensor
for close cycle
on gate.
er
nt
r
e
apm
Ent
ety
f
a
S p
e
d
tsi Loo
u
O
er
ty
e
Saf
g
Dan
ety
f
a
S p
e
o
d
i
Ins Lo
e
sid
In
Safety loops allows the gate to stay open
when vehicles are obstructing the gate path.
Suggested for vehicles 14 feet or longer.
See pages 20 and 21.
6
ty
P
r
e
p
ro
g
Dan
Gate Rail Stops
For safety
reasons, physical
stops MUST be
installed on both
ends of the gate
rail prior to
installation of the
gate operator.
This will assure
that the gate does
not derail while
opening or
closing fully.
See page 9.
SAFET Y PRECAUTIONS
THE ROBOSLUL3™ IS FOR USE ON VEHICULAR PASSAGE GATES ONLY
AND NOT INTENDED FOR USE ON PEDESTRIAN PASSAGE GATES.
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
Property owners MUST never mount any
gate operating device near the gate's path!
Property owners MUST never allow
anyone to hang or ride on the gate!
Property owners MUST never let pedestrians
cross the path of a moving gate!
WARNING SIGN PL ACEMENT
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
Install Warning signs on BOTH sides of EACH gate in PLAIN VIEW.
7
Installation
I N S TA L L AT I O N S E T U P S
Front or Rear Position with Single Operator
2 inch wire grid safety screen 48 inches high.
Front Position
Low Voltage UL approved conduit
Maximum gate length 20 ft.
Maximum gate weight is 800 lbs.
High Voltage UL approved conduit
Concrete Pad
Warning Placard on both sides of gate.
UL approved catch roller with safety cover.
Rear Position
Idler pulley MUST have safety cover.
Earth Ground Rod is highly recommended.
Weld physical stops
on ends of gate rail.
Master/Second Operators
Maximum gate length 20 ft. for each gate.
Maximum gate weight is 800 lbs. for each gate.
UL approved catch rollers
with safety covers.
Separate power supply for each operator.
Warning Placard on both sides of each gate.
2 inch wire grid safety screen 48 inches high.
Low Voltage UL approved conduit
High Voltage UL approved conduit
Earth Ground Rod is highly recommended for each operator.
8
Weld physical stops
on ends of gate rail.
Concrete Pad
S A F E T Y C AT C H R O L L E R S A N D G AT E R A I L S T O P S
DO NOT use a
Gate Catch Post.
Because the coasting distance may
vary due to changes in temperature,
it is NOT recommended to install a
stop or catch post in front of the
gates path. To do so will cause the
gate to hit the post in certain
instances.
te
g
sin
Ga
Clo
ate
G
ing
s
Clo
It is only recommended to install catch
rollers with safety covers on the side of a
post or wall with a minimal distance of half
an inch between the rollers and gate.
Gate Rail Stop
1/2"
1/2"
When fully opened, the end of the sliding gate should
stop at least five inches from an obstructing wall.
5"
End View of Gate and Wall
Note: For safety reasons, physical stops MUST be installed on both ends of the gate
rail prior to installation of the gate operator. This will assure that the gate does not
derail while opening or closing fully.
9
M O U N T I N G O P E R AT O R
4 Concrete Anchors
1/2" x 3 1/2"
Above
Ground 6"
Below the frost line.
Check all local codes.
Co
nc
ret
UL approved underground conduit(s).
High voltage power wires run in
separate conduit.
eP
ad
20"
15"
C H A I N I N S TA L L AT I O N
Over time, the gate’s chain will stretch out and need to have links removed from it. The links can be removed during normal periodic
maintenance of the operator.
CORRECT INSTALLATION
INCORRECT INSTALLATION
2 inch
wire grid
safety
screen is
missing.
Don’t connect chain
too tight to gate.
Chain is
mounted
too high
or
too low
on gate.
Chain is too loose on gate.
Top of Gate
Top of Gate
Gate is 4 inches minimum
away from drive sprocket.
Class 2
Supply
Operator is mounted
too close to gate.
10
CONTROL BOARD DESCRIPTION
Limit Switch Harness Connection
A
6
7 CHARGEOK
BATTERY
LOW
8
OFF
60
ON
MASTER
SECOND
ON
OFF
2.5
3
0
25
TIMER
DELAY
23
26
REVERSE
SENSOR
ALARM
SENSOR
MOTOR
RUN
10
13
FIRE
DEPT
EXIT
LOOP
12
LIMIT
OPEN
STRIKE
14ST
OPEN
O
SAFETY
LOOP
15
LIMIT
CLOSE
16
RADIO
R
CMD
CENTER
LOOP
18
LIMIT
ERROR
19
11
24 BIPART
22
COMMAND
PROCESSED
17
Not Used
21
ON
OFF
OPEN
STOP
3-Button Control Station,
Stop Button
(See page 18)
Open (N.O.)
Stop (N.C.)
Close (N.O.)
POWER
27
Maglock/Solenoid
Connection
(See page 19)
Maglock (N.C.)
W4
28
NC
MAGLOCK
COM
COM
Solenoid (N.O.)
RESET
NO
Built-In Reset Button
(See page 28)
BATTERY
Motor Connection
12 VDC Motor
MOTOR
AC POWER
External Power
18 Vac transformer OR
“Optional” Solar Power
Surge Suppressor Links
Master/Second
Surge Link
External Devices
Surge Link
On-Board
Command
Buttons
CLOSE
Plug-In Loop Detectors
(See page 20)
Power Plug Connection
(See page 14)
12 VDC Battery
Connection
3-PUSH BUTTON STATION
EXIT
4
SYSTEM ON
G
OPEN
SAFETY CENTER
PLUG-IN LOOPS
EXIT
Plug-In Loop Wires
(See page 20)
Exit Loop Wires
Safety Loop Wires
Center Loop Wires
SAFETY
3
M/S
FAIL
OPEN OPEN
LEFT RIGHT
21
UL ALARM
ENTRAPMENT
M/S
5 LINK
9
CENTER
20
UL OPEN
SENSOR
UL CLOSE
SENSOR
B
M/S LINK
POSITIVE STOP
1
POSITIVE STOP
UL CONNECTOR
SENSOR SENSOR
OPEN CLOSE
UL Sensor
Close Direction
(See pages
16 and 17)
2
CLOSE STOP
ALARM
UL Connectors
UL Alarm
(See page 29)
UL Sensor
Open Direction
(See pages
16 and 17)
Board Wiring Diagram on page 34.
Motor Fuse 20 Amp, 32 V
ROBO UL
Charging Fuse 4 Amp
Check 4 Amp Fuse LED
Fuse blown when ON
Circuit Board
Power
15 Safety Loop - Detector activated when ON.
16 Limit Close - Close limit switch activated when ON.
17 Radio Cmd - Transmitter is activated when ON.
1 UL Close - UL Close sensor is activated when ON.
18 Center Loop - Not used.
2 UL Open - UL Open sensor is activated when ON.
19 Limit Error - Open/Close limit switch malfunction when ON.
3 UL Alarm Entrapment - UL entrapment level 1 or 2 condition
has occurred when ON.
20 Open Left/Right - Movement direction, see page 22.
4 System On - All systems active during gate cycling.
22 Timer - Timed Close, see page 23.
5 M/S Link - Flashes during communication between units.
23 Reverse Sensor - Gate hit obstruction when ON. See page 26.
6 M/S Fail - Unsuccessful communication between units.
24 Bi-Part - Not used.
7 Charge OK - Battery charging successfully when ON.
25 Delay - Not used.
8 Battery Low - Battery voltage too low to operate gate when ON.
26 Alarm Sensor - Limited adjustment, see page 26.
9 Command Processed - Successful command executed.
27 W4 - Stop Jumper, to remove, see page 18.
10 Motor Run - Motor operating when ON.
28 Maglock/Solenoid LED - Is activated when ON, see page 19.
21 Positive Stop - Not used.
11 Fire Dept - Key Switch activated when ON.
CAUTION
12 Exit Loop - Detector activated when ON.
To AVOID damaging the control board, replace fuses ONLY
with same type and rating specified above.
13 Limit Open - Open limit switch activated when ON.
14 Strike Open - Strike connected device activated when ON.
11
SURGE SUPPRESSOR TERMINAL CONNECTIONS
Output Power
11
13
®
Robo-ULSurge Suppressor
G B A
P/N Q410
P/N 001C6064
Patent
Pending
7 8 9 10Patent
11Pending
12 13
1 2 3 4 5 6
–
G
Separate power
for second operator.
B
M/S Link
A
Center
Loop
Safety
Loop
Exit
Loop
– Ground
+ 12 VDC
Fire Dept
Key Switch
Strike Open
Push Button
+
Radio
Receiver
Class 2
Supply
24 Volts DC
CAUTION
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside
removable terminal connections.
• DO NOT let wire insulation interfere with connection.
G
B
A
Page 15
Master/Second Operator Link
315 MHz Factory Installed
Radio Receiver
Power
11
1 Red
13 + 12 Volt
13
2 Black
11 – Neg.
Page 21
12
3
4
Com.
11 – Neg.
3 White
®
4 Green
Remote Programming on pages 24 and 25.
Remote NOT Provided
External 12 VDC “Safety” Loop Detector
Separate power
for card reader.
Power
11
13
Page 21
Card Reader
10
5
6
9
External 12 VDC “Exit” Loop Detector
Push Button
10
9
Dry Contact
Telephone Entry System
Power
11
13
Page 17
10
3
9
4
1
4
7
HELP
Separate power
for TES.
12 VDC Photo Electric Sensor (Safety)
Fire or any Key Switch
NOTE: Terminals 11 and 12 are the ONLY terminals that will
Open and Close with a single push of a button. All other
terminals will ONLY open with a single push of a button.
8
7
12
Dry Contact
2
3
5
6
8
9
0
Wiring
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
• DO NOT install any wiring or attempt to run the operator
without consulting the wiring diagram. We recommend that
you install an optional reversing edge BEFORE proceeding
with the control station installation.
• ANY maintenance to the operator or in the area near the
operator MUST not be performed until disconnecting the
electrical power and locking-out the power via the operator
power switch. Upon completion of maintenance the area
MUST be cleared and secured, at that time the unit may be
returned to service.
• ALL power wiring should be on a dedicated circuit and well
protected. The location of the power disconnect should be
visible and clearly labeled.
• Disconnect battery and 18 Vac transformer or solar panel
BEFORE proceeding. Operator MUST be properly grounded
and connected in accordance with local electrical codes.
NOTE: The operator should be on a separate fused line of
adequate capacity.
• ALL power and control wiring MUST be run in separate
conduit.
• BEFORE installing power wiring or control stations be sure to
follow all specifications and warnings described below. Failure
to do so may result in SEVERE INJURY to persons and/or
damage to operator.
• ALL electrical connections MUST be made by a qualified
individual.
All power wiring should be on a dedicated circuit and well protected.
NOTE: Calculated using NEC guidelines. Local codes and conditions must be reviewed for suitability of wire installation.
WARNING
CAUTION
To AVOID damaging 18 Vac plug-in transformer, it MUST be
enclosed in a suitable weatherproof enclosure and provided
with proper weatherproof fixtures.
To prevent SERIOUS INJURY or DEATH from a moving gate:
DO NOT disconnect the built-in audio alarm or reset switch.
Use 14 gauge / 300 watt direct burial, landscape
lighting wire NOT to exceed 1000 ft. for transformer.
E A R T H G R O U N D R O D I N S TA L L AT I O N
Proper grounding gives an electrical charge, such as from an electrical static discharge
or a near lightning strike, a path from which to dissipate its energy safely into the earth.
Without this path, the intense energy generated by lightning could be directed towards
the gate operator. Although nothing can absorb the tremendous power of a direct
lightning strike, proper grounding can protect the gate operator in most cases.
Within
3 Feet
The earth ground rod must be located within 3 feet from the gate operator. Use the
proper type earth ground rod for your local area.
The ground wire must be a single, whole piece of wire. Never splice two wires for the
ground wire. If you should cut the ground wire too short, break it, or destroy its
integrity, replace it with a single wire length.
CAUTION
To AVOID damaging gas, power, or other underground utility
lines, contact underground utility locating companies
BEFORE digging more than 18" (46 cm) deep.
13
Single piece of
12 gauge wire.
Check local
codes for
proper
depth.
DC POWER CONNECTION
Earth Ground Rod Highly Recommended!
Off
Off
On
Air (1)
Conditioner
Main
Room
Off
On
Off
Conference
Room 1
Off
Conference
Rm 2, 3
Off
Refer.
Bus 1, 2, 3
On
SAFETY CENTER
Only Battery Connected:
Only Power LED will remain on.
XIT
TY E
AFE
ER S
CENT
On
EXIT
Only Transformer Connected:
Power LED is on, Charge OK LED is on.
Conference
Room 2
Comp.
Serve 2
Eug. Dept.
Manu. 1 Rm
Factory
Installed
Battery
ROBOSLUL3™
Main Power
Disconnect
Plug
Off
Air (2)
Conditioner
Comp.
Serve 1
ROBO (1)
ROBO (2)
Main Dept.
Manu. 2 Rm
Use a dedicated circuit for
each operator’s transformer.
Input power to transformer,
120 Vac, 60 Hz.
18 Vac Plug-in Transformer
Use 14 gauge / 300watt direct burial, landscape
lighting wire NOT to exceed 1000 ft. (Not provided)
Polarity does NOT matter.
CAUTION
To AVOID damaging 18 Vac plug-in transformer, it MUST be
enclosed in a suitable weatherproof enclosure and provided
with proper weatherproof fixtures.
To AVOID damaging control board, DO NOT use the solar panel
and the plug-in transformer at the same time.
Solar Panel
No Stand
Part # SOLAR3
Contact your local dealer for more information about solar power.
14
L I N K I N G M A S T E R / S E C O N D O P E R AT O R S
18 Vac plug-in transformer required for each operator.
Never run high voltage and low voltage wires in same conduit.
Run low voltage 16-18 gauge wire in UL approved conduit to connect operators together.
Connect Master M/S Link G to Second M/S Link G.
Connect Master M/S Link B to Second M/S Link B.
Connect Master M/S Link A to Second M/S Link A.
Use shielded twisted
wires for M/S link.
Shield wire MUST be
grounded to master
operator only.
+
–
B
A
M/S Link
Center
Loop
Safety
Loop
Exit
Loop
Fire Dept
Key Switch
Strike Open
Push Button
Radio
Receiver
G
CHARGE
OK
BATTERY
LOW
MASTER
SECOND
ON
OFF
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
EXIT
LOOP
LIMIT
OPEN
STRIKE
ST
OPEN
O
SAFETY
LOOP
LIMIT
CLOSE
RADIO
RA
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
Safety
Loop
Exit
Loop
Fire Dept
Key Switch
Strike Open
Push Button
Class 2
Supply
Radio
Receiver
A
24 Volts DC
B
G
M/S LINK
UL OPEN
SENSOR
UL CLOSE
SENSOR
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
ON
OFF
OFF
60
SYSTEM ON
CENTER
3-PUSH BUTTON STATION
FIRE
DEPT
D
OPEN
MOTOR
RUN
COMMAND
PROCESSED
Center
Loop
PLUG-IN LOOPS
EXIT
M/S
FAIL
3
SAFETY CENTER
SAFETY CENTER
SAFETY
M/S
LINK
ON
POSITIVE STOP
POSITIVE STOP
60
A
UL CONNECTOR
OFF
BIPART
SENSOR SENSOR EXIT
OPEN CLOSE
ON
OFF
SYSTEM ON
CENTER
B
B
M/S Link
ALARM
UL ALARM
ENTRAPMENT
PLUG-IN LOOPS
SENSOR SENSOR EXIT
OPEN CLOSE
UL CONNECTOR
ALARM
A
OPEN OPEN
LEFT RIGHT
+
–
G
24 Volts DC
M/S LINK
UL OPEN
SENSOR
UL CLOSE
SENSOR
P/N Q410
P/N 001C6064
Patent
Pending
Patent Pending
G B A
Class 2
Supply
CLOSE STOP
G
Robo-UL Surge Suppressor
SAFETY
NOTE: To adjust
timers, see page 23.
EXIT
M/S
LINK
M/S
FAIL
CHARGE
OK
BATTERY
LOW
3
MASTER
SECOND
ON
OFF
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
DEPT
D
EXIT
LOOP
LIMIT
OPEN
STRIKE
ST
OPEN
O
SAFETY
LOOP
LIMIT
CLOSE
RADIO
RA
CMD
CENTER
LOOP
LIMIT
ERROR
CLOSE
ON
BIPART
OPEN
STOP
3-PUSH BUTTON STATION
G B A
®
OPEN
P/N Q410
P/N 001C6064
Patent
Pending
Patent Pending
CLOSE STOP
Robo-UL Surge Suppressor
POSITIVE STOP
®
POSITIVE STOP
Shield Wire
CLOSE
POWER
POWER
W4
W4
NC
MAGLOCK
MAGLOCK
NC
COM
COM
RESET
NO
RESET
NO
COM
COM
BATTERY
BATTERY
MOTOR
MOTOR
AC POWER
AC POWER
ROBO UL
ROBO UL
Master Board
Second Board
Master/Second control boards are interchangeable,
provided DIP switches and timers are set appropriately
when swapping boards.
15
NOTE: Disconnect the
second radio receiver
when using a
master/second setup.
ENTRAPMENT PROTECTION DEVICES
Contact Sensors (Edge Sensor)
WARNING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
NOTE: When touched, these electrically activated edge sensors immediately signal the gate operator to stop and reverse. Property
owners are obligated to test edges monthly. See page 31 for edge sensor part numbers.
Entrapment Danger
Gate in Open Position
Outside Property
Inside Property
PrOuts
op id
ert e
y
r
ge
an
tD
en
pm
tra
En
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
Sensor
Open
on Wall
Open Contact
Sensor
ON
OFF
60
G
CHARGE
OK
BATTERY
LOW
SECOND
OFF
ON
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
Sensor Open
on Wall
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
MOTOR
RUN
COMMAND
PROCESSED
OPEN
STOP
3-PUSH BUTTON STATION
EXIT
M/S
FAIL
3
CLOSE STOP
SAFETY CENTER
PLUG-IN LOOPS
EXIT
SAFETY
M/S
LINK
ON
POSITIVE STOP
POSITIVE STOP
OFF
SYSTEM ON
CENTER
B
BIPART
MASTER
e y
id rt
s e
In p
ro
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
P
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
A
M/S LINK
UL OPEN
SENSOR
UL CLOSE
SENSOR
CLOSE
Sensor Open on Gate
POWER
W4
Outside Property
MAGLOCK
NC
COM
COM
Safety Danger
RESET
NO
BATTERY
Gate in Open Position
AC POWER
MOTOR
Inside Property
ROBO UL
Sensor
Close
on Wall
Close Contact
Sensor
Sensor Close on Gate
16
er
ng
Da
P
ty e y
fe id rt
Sa s e
In p
ro
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
PrOuts
op id
ert e
y
ENTRAPMENT PROTECTION DEVICES
Non-Contact Sensors (12 VDC Photo Electric Sensors)
NOTE: Property owners are obligated to test photo sensors monthly.
Outside Property
Entrapment Danger
Inside Property
P/N Q410
P/N 001C6064
Patent
Pending
®
Robo-UL Surge Suppressor
G B A
7 8 9 10Patent11Pending
12 13
1 2 3 4 5 6
+
–
A
Center
Loop
M/S Link
Safety
Loop
A
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
OFF
ON
B
G
OFF
60
SYSTEM ON
M/S
LINK
M/S
FAIL
CHARGE
OK
BATTERY
LOW
SECOND
OFF
ON
2.5
3
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
EXIT
ON
BIPART
MASTER
ALARM
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
SENSOR SENSOR EXIT
OPEN CLOSE
CLOSE
POWER
NC
MAGLOCK
COM
COM
NO
Power
MOTOR
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
W4
RESET
e y
id rt
s e
In p
ro
It is best to use 12 VDC Failsafe Photo
Electric Sensors for this Safety Option
Failsafe Photo Sensors: If a failsafe photo
sensor is not working or loses power or
photo beam is blocked, then the photo beam
will stop ALL gate operation.
r
e y
id t
s er
In p
o
P
ety
UL OPEN
SENSOR
ROBO UL
ROB
Safety Non-Contact Sensor
Saf
24 Volts DC
M/S LINK
UL CLOSE
SENSOR
P
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Locate entrapment protection devices to protect in BOTH
the open and close gate cycles.
• Locate entrapment protection devices to protect between
moving gate and RIGID objects, such as posts or walls.
Class 2
Supply
Radio
Receiver
Power
SAFETY
SAFE
WARNING
Strike Open
Push Button
OPEN
Orange
Fire Dept
Key Switch
Blue 11 13 Brown
UL CONNECTOR
Open
Non-Contact
Sensor
ALARM
r
ge
an
tD
en
pm
tr a
En
Part
u# AOMRON12V (Failsafe)
PrO
op tsid
ert e White
y
Exit
Loop
POSITIVE STOP
B
POSITIVE STOP
12 VDC ONLY!
G
CLOSE STOP
Gate in Open Position
NOTE: If the photo beam gets blocked while
the gate is closing, it will stop and reopen.
The gate will remain open until the
obstruction is cleared.
Dan
ger
®
Robo-UL Surge Suppressor
G B A
P/N Q410
P/N 001C6064
Patent
Pending
7 8 9 10Patent11Pending
12 13
1 2 3 4 5 6
e
id ty
ts r
u e
O op
r
P
–
G
B
M/S Link
A
Center
Loop
Safety
Loop
4
Orange 3
Exit
Loop
Fire Dept
Key Switch
Strike Open
Push Button
Part # AOMRON12V (Failsafe)
17
Class 2
Supply
24 Volts DC
White
Blue 11 13 Brown
12 VDC ONLY!
Contact your local dealer for more
information about photo electric sensors.
+
Radio
Receiver
Power
3 - B U T T O N C O N T R O L S TAT I O N O R S T O P B U T T O N
3-Button Control Station
CAUTION
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside
removable terminal connections.
• DO NOT let wire insulation interfere with connection.
There are NO
common wires
within this 3-button
control station.
Open-N.O. Contact
Stop-N.C. Contact
Close-N.O. Contact
OPEN OPEN
LEFT RIGHT
OFF
ON
OFF
60
G
CHARGE
OK
BATTERY
LOW
SECOND
OFF
ON
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
MOTOR
RUN
COMMAND
PROCESSED
OPEN
STOP
Stop Button
3-PUSH BUTTON STATION
EXIT
M/S
FAIL
3
BIPART
MASTER
CLOSE STOP
SAFETY CENTER
PLUG-IN LOOPS
EXIT
SAFETY
M/S
LINK
ON
POSITIVE STOP
UL OPEN
SENSOR
UL ALARM
ENTRAPMENT
SYSTEM ON
CENTER
B
M/S LINK
UL CLOSE
SENSOR
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
A
Part # 02-103
CLOSE
POWER
W4
MAGLOCK
NC
COM
COM
NO
IN
RESET
Install the stop
button in a secure
accessible place.
BATTERY
MOTOR
AC POWER
ROBO UL
Part # AEXITP
4
W
The Stop Button will stop the audio alarm and reset operator.
Use the Stop Button to::
• To stop the movement of the gate in case of potential entrapment.
• To stop the audio alarm, (check for obstructions).
• To reset the operator after the alarm has triggered.
If either stop button is installed as shown,
move the shorting block so that the two
pins of W4 are not shorted.
18
SOLENOID/MAGLOCK CONNECTION
UL OPEN
SENSOR
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
ON
OFF
OFF
60
SYSTEM ON
B
Relay Contact Rating
0.68 Amp - 125 VAC
2 Amp - 30 VDC
G
BATTERY
LOW
ON
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
EXIT
CHARGE
OK
SECOND
OFF
OPEN
SAFETY
M/S
FAIL
3
BIPART
MASTER
CLOSE STOP
SAFETY CENTER
PLUG-IN LOOPS
EXIT
CENTER
M/S
LINK
ON
POSITIVE STOP
UL CLOSE
SENSOR
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
A
M/S LINK
CLOSE
POWER
W4
Part # MG1300
MAGLOCK
NC
COM
COM
RESET
NO
BATTERY
Maglock
MOTOR
AC POWER
ROBO UL
LED will light when
Solenoid/Maglock is
activated.
N.C.
MAGLOCK
NC
Separate Power
for Maglock
Common
COM
COM
NO
N.O.
Solenoid
CAUTION
Separate Power
for Solenoid
Common
19
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside
removable terminal connections.
• DO NOT let wire insulation interfere with connection.
PLUG-IN LOOP DETECTOR WIRING
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
OFF
ON
OFF
60
EXIT
M/S
FAIL
CHARGE
OK
BATTERY
LOW
BIPART
MASTER
SECOND
OFF
ON
2.5
3
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
STRIKE
ST
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
DETECT
LOOP FAIL
The wire MUST be
twisted together
6 twists per foot from
the end of the loop to
the control board.
CLOSE STOP
POWER ON
STOP
3-PUSH BUTTON STATION
PLUG-IN LOOPS
EXIT SAFETY CENTER
SAFETY
M/S
LINK
ON
POSITIVE STOP
UL OPEN
SENSOR
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
Plug-In Loop Detectors
Part # AELD (Sold Individually)
G
M/S LINK
UL CLOSE
SENSOR
SYSTEM ON
CENTER
B
OPEN
ALARM
A
CLOSE
POWER
W4
FREQUENCY
NC
MAGLOCK
SENSITIVITY
BOOST
®
™
COM
COM
RESET
NO
BATTERY
CAUTION
MOTOR
AC POWER
ROBO UL
To AVOID damaging control board,
disconnect all power to operator before
installing plug-in loop detectors.
Use a different frequency for every loop
detector installed.
Safety Loop
Exit Loop
Plug-In “Exit” Loop Detector - Allows
gate to automatically open for exiting
vehicles.
Example of a 2 wire loop. (See
“Installing Insulated Loop Wire” on
next page for more information)
Plug-In “Safety” Loop Detector - Allows
gate to stay open when vehicles are
obstructing path. Caution: Suggested for
vehicles 14 feet or longer.
If the “Inside” and “outside” safety loops
are connected to the same loop detector:
• They should be series connected to the
detector
• Have the same dimensions.
• Have the same number of wire turns.
Example of a 3 wire loop. (See “Installing
Insulated Loop Wire” on next page for
more information)
Note: Refer to the plug-in
loop detector manual for
more specific information.
PrOut
op sid
ert e
O
SAUTS
y
LO FE ID
OP TY E
SAINS
FE ID
LO
OP TYE
IT
X P
E O e y
O
t
L id r
s e
In op
r
P
Contact your local dealer for information
about plug-in loop detectors.
20
12 VDC EXTERNAL LOOP DETECTOR WIRING
®
Robo-UL Surge Suppressor
G B A
PrOut
op sid
ert e
O
S UT
y
Note: Refer to the 12
VDC loop detector
manual for more
specific information.
1 2 3 4 5 6
P/N Q410
P/N 001C6064
Patent
Pending
7 8 9 10Patent11Pending
12 13
–
G
B
A
Center
Loop
M/S Link
LOAFE SID
OP TY E
Safety
Loop
Exit
Loop
Fire Dept
Key Switch
Strike Open
Push Button
+
Radio
Receiver
–
Class 2
Supply
24 Volts DC
+
SAINS
FE ID
LO
OP TYE
IT
X P
E O e y
O
t
L id r
s e
In op
r
P
Part # A23
(Sold Individually)
11
13
3
4
12 VDC External “Safety” Loop Detector - Allows gate to stay open when vehicles
are obstructing path. Caution: Suggested for vehicles 14 feet or longer.
If the “Inside” and “outside” safety loops are connected to the same loop detector:
• They should be series connected to the detector
• Have the same dimensions.
• Have the same number of wire turns. (See table below)
11
13
12 VDC External “Exit” Loop Detector - Allows gate to automatically open for exiting
vehicles.
5
6
Installing Insulated Loop Wire
Number of Wire Turns Needed for Loop Sizes
Number of Wire Turns
Loop Perimeter
10 feet to 13 feet
14 feet to 26 feet
27 feet to 80 feet
80 feet and up
4
3
2
1
The wire is continuously wound in
the loop saw cut for the required
number of turns. One turn shown.
(Refer to table)
Saw Cut
The wire MUST be twisted together 6 twists per foot
from the end of the feeder slot to the loop detector.
Remove sharp inside corners
by making corner cuts
Home Run
Feeder Slot
1/8" to 1/4" Width Saw Cut
Road Surface
Min 1"
Sealant
Recommended Loop Wire XLPE 12-18 gauge
(Use heavier wire gauge for a more durable
loop area).
Backer Rod
Insulated loop wire
3 turns shown, amount varies.
Refer to table
2" to 2.5" Depth
Saw Cut
21
NOTE: Wire mesh or reinforcement
imbedded in the road surface should be
cut away a minimum of 6 inches from
the perimeter of the loop wires.
Adjustments
CAUTION
To reduce the risk of SERIOUS INJURY or DEATH:
Disconnect power BEFORE performing ANY adjustments.
S ET G AT E O P E N I N G D I R E C T I O N
PrOut
op sid
ert e
y
PrOut
op sid
ert e
y
ey
t
id r
s e
In op
r
P
ey
t
id r
s e
In op
r
P
60
60
EXIT
M/S
FAIL
CHARGE
OK
BATTERY
LOW
ON
3
SECOND
OFF
ON
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
CLOSE
POWER
W4
OPEN
LEFT
OPEN
RIGHT
ON
OFF
3
OFF
60
ON
POSITIVE STOP
OFF
3-PUSH BUTTON STATION
SAFETY
M/S
LINK
RA
RADIO
CMD
OFF
G
OPEN
CENTER
B
BIPART
MASTER
POSITIVE STOP
ON
POSITIVE STOP
POSITIVE STOP
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
OFF
CLOSE STOP
POSITIVE STOP
ON
SAFETY CENTER
OFF
UL OPEN
SENSOR
SYSTEM ON
PLUG-IN LOOPS
EXIT
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
ON
OFF
MASTER
UL CONNECTOR
ALARM
OPEN OPEN
LEFT RIGHT
A
M/S LINK
UL CLOSE
SENSOR
MASTER
OFF
3
MAGLOCK
NC
COM
COM
RESET
NO
BATTERY
TIMER
MOTOR
AC POWER
Open to the LEFT
ROBO UL
TIMER
Open to the RIGHT
LIMIT SWITCH ADJUSTMENTS
Each notch is an estimated
one inch of gate travel.
Push and hold lock plate to release limit nuts.
Roll limit nuts to adjust the open and close limit switches.
22
SETTING TIMER
Single Operator
UL CONNECTOR
ON
OFF
60
B
G
CHARGE
OK
BATTERY
LOW
SECOND
OFF
ON
2.5
3
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
ST
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
EXIT
M/S
FAIL
BIPART
MASTER
OPEN
STOP
3-PUSH BUTTON STATION
SAFETY CENTER
PLUG-IN LOOPS
EXIT
SAFETY
M/S
LINK
ON
POSITIVE STOP
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
OFF
SYSTEM ON
CENTER
To use the push close command, the
timer should be switched to the “OFF”
position.
UL OPEN
SENSOR
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
Set Timer
3 to 60 seconds
A
M/S LINK
UL CLOSE
SENSOR
CLOSE STOP
ALARM
To use the automatic close for the gate system
the timer switch should be put in the “ON”
position.
CLOSE
POWER
W4
MAGLOCK
NC
COM
COM
RESET
NO
BATTERY
MOTOR
AC POWER
ROBO UL
Master/Second Operators
Operators need to be connected by M/S LINK. See page 15.
Master/Second control boards are interchangable, provided DIP switches
and timers are set appropriately when swapping boards.
Master Board
with Timers ON
Second Board
1. Turn BOTH timers ON.
3. Use Timer on Master Board Only.
(3 to 60 seconds)
Master Board
2. Turn Second Timer to Maximum
Counterclockwise Setting.
with Timers OFF
1. Turn BOTH timers OFF.
23
Second Board
315 MHZ RADIO RECEIVER PROGRAMMING
Setting Security Mode (High) or (Normal):
The receiver is factory set at HIGH security mode. To verify, refer to the label next to jumper P4. (See illustration below)
The Receiver can be used with up to 15 rolling code remotes or passwords in HIGH security mode. Alternately, it can be used with up
to 31 of any type remote in NORMAL security mode, including any combination of rolling code, billion code, or dip switch remotes.
When changing from NORMAL to HIGH security mode, all previous remote control codes must be erased. See next page to erase and
reprogram remote controls that are being used.
CAUTION
H
IG
O
R
M
H
N
N
O
R
M
H
IG
H
To AVOID damaging receiver, disconnect receiver’s power before
changing jumpers.
Changing security from High to Normal.
WARNING
To reduce the risk of SERIOUS INJURY
or DEATH from a moving gate:
P4
• ALWAYS keep remote controls out of
reach of children. NEVER permit
children to operate, or play with
remote control.
• Activate gate ONLY when it can be
seen clearly, is properly adjusted, and
there are no obstructions in gate’s
path.
• ALWAYS keep gate in sight until
completely closed. NEVER permit
anyone to cross path of a moving
gate.
C
M
C
M
P2
Changing output duration from Momentary to Constant.
Setting Output Duration (M) or (C):
The receiver is factory set at (M) Momentary. To verify, refer to the label next to jumper P2. (See illustration above)
For commercial applications, the receiver can be set to either (C) constant or (M) momentary closure.
With the jumper in the (M) momentary position, the contacts will close for 1/4 second regardless of the length of remote control
transmission.
With the jumper in (C) constant position, the contacts will stay closed as long as the remote control continues transmitting. Push and
HOLD remote button to open or close gate.
WARNING
To reduce the risk of SERIOUS INJURY or DEATH, the use of
CONSTANT OPERATION on residential operators is PROHIBITED.
24
315 MHZ RADIO RECEIVER PROGRAMMING
IMPORTANT: Hand Held Remote NOT provided.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
NOTE: Receiver wiring on page 12 or 34.
Disconnect the second receiver when
using a master/second setup.
Programming Radio Receiver:
1. Press and release the “Learn ” button on the receiver. The learn
indicator light will glow steadily for 30 seconds.
Learn
Button
2. Within 30 seconds, press and hold the button on the hand-held remote.
The operator will now operate when the push button on the remote
control is pressed.
Repeat Steps 1 and 2 for each remote control that will be used.
Erase ALL Remote Control Codes:
Press and hold the “Learn ” button on the receiver panel until the indicator light turns off
(about 6 seconds). All previous codes are now erased. Reprogram each remote you wish
to use.
Optional 315 MHz Hand Held Remotes
Part # 371LM
Part # CPT13
Part # 372LM
Part # CPT23
Part # 373LM
Part # CPT33
Mini 3 Button
Part # CPTK33
Mini 3 Button
Part # 370LM
Part # 374LM
Part # CPT43
25
Mini 3 Button with
HID Prox, Sensor
Part # CPTK33PH
ADJUSTING REVERSING SENSOR
Adjust the “Reverse Sensor” on the control board. Alarm Sensor does not need to be adjusted except where noted below.
The level of reverse sensitivity depends on the weight of the gate
and the condition of installation.
Sensor is set too sensitive = if the gate stops in midcycle or reverses by itself.
Sensor is not set sensitive enough = if the gate hits an object and does not stop or reverse.
OPEN OPEN
LEFT RIGHT
ON
OFF
OFF
60
SYSTEM ON
B
G
BATTERY
LOW
ON
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
DEPT
D
EXIT
LOOP
LIMIT
OPEN
STRIKE
STR
OPEN
O
SAFETY
LOOP
LIMIT
CLOSE
RADIO
RA
CMD
C
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
EXIT
CHARGE
OK
SECOND
OFF
OPEN
SAFETY
M/S
FAIL
3
BIPART
MASTER
CLOSE STOP
SAFETY CENTER
PLUG-IN LOOPS
EXIT
CENTER
M/S
LINK
ON
POSITIVE STOP
UL ALARM
ENTRAPMENT
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
UL CONNECTOR
ALARM
Maximum
Sensitivity
A
M/S LINK
UL OPEN
SENSOR
UL CLOSE
SENSOR
CLOSE
POWER
W4
Minimum
Sensitivity
MAGLOCK
NC
COM
COM
RESET
NO
BATTERY
MOTOR
AC POWER
Note: If the power supply to the plug-in transformer is less than
99 volts, adjust the alarm sensor by turning the alarm
adjustment counter-clockwise enough to actuate the alarm when
obstructed but not sensitive enough for false triggering to occur.
ROBO UL
26
Maintenance and Operation
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. NEVER let children operate or play with gate controls.
Keep the remote control away from children.
3. ALWAYS keep people and objects away from the gate.
NO ONE SHOULD CROSS THE PATH OF THE MOVING
GATE.
4. Test the gate operator monthly. The gate MUST reverse
on contact with a rigid object or stop when an object
activates the non-contact sensors. After adjusting the
force or the limit of travel, retest the gate operator.
Failure to adjust and retest the gate operator properly
can increase the risk of INJURY or DEATH.
5. Use the emergency release ONLY when the gate is not
moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the
owner’s manual. Have a qualified service person make
repairs to gate hardware.
7. The entrance is for vehicles ONLY. Pedestrians MUST
use separate entrance.
8. Disconnect ALL power BEFORE performing ANY
maintenance.
9. ALL maintenance MUST be performed by a Chamberlain
Elite professional.
10.
SAVE THESE INSTRUCTIONS.
MAINTENANCE:
1. Disconnect power before servicing.
2. The gate area should be kept clean to insure proper operation.
3. Make sure the reversing sensor is functioning properly. Check it monthly. (Page 26)
4. Make sure the gate track is clear of dirt, rocks or other substances.
5. Make sure the wheels are operating smoothly on the track.
6. Oil the chain regularly with a chain lubrication oil available at most motorcycle stores.
7. Replace blown fuses ONLY with sizes specified. (Page 11)
8. Check for proper synthetic oil level in the gear box. (10W-30 weight synthetic oil)
9. Severe or high cycle usage will require more frequent maintenance checks.
10. Inspection and service should always be performed anytime a malfunction is observed or suspected.
11. When servicing, please do some “house cleaning” of the operator and the area around the operator. Pick up any debris in the area.
Clean the operator as needed.
12. It is suggested that while at the site voltage readings be taken at the operator. Using a Digital Voltmeter, verify that the incoming
voltage to the operator it is within ten percent of the operators rating.
CAUTION
To reduce the risk of FIRE or INJURY to persons use ONLY
Chamberlain part # ABT12 for replacement battery.
27
B U I LT- I N R E S E T B U T T O N
When the gate operator’s audio alarm (See next page) has been tripped, the reset button must be pushed ONCE to shut the alarm off.
The button MUST be pressed AGAIN to reset the operator.
If the audio alarm goes off, always check the gate area for:
• Obstructions in the gate path.
• Damage to the gate and/or gate operator.
1
• Shuts off alarm.
• Stops the gate while cycling.
• Allows gate to be manually
pushed open.
Press button ONCE.
• Resets operator.
2
Press button AGAIN.
Note: If the gate is in mid-cycle and the reset button is pressed ONCE, the gate will stop, just like a stop button. The reset button MUST
be pressed AGAIN and another physical command given (i.e. push remote control button) for the gate to finish the cycle.
28
AUDIO ALARM
The alarm could be tripped when one of the following happens Twice Consecutively,
then the alarm will sound for 5 minutes or until the reset button is pressed!
Press the Built-In Reset Button Once to Shut Off Alarm and Again to Reset Operator (See previous page)
The gate is hitting a wall or vehicle.
The gate is TOO heavy.
Debris is on the gate's track such as mud, rocks, dirt, etc.
An externally wired safety sensor has been triggered twice.
(Photo beam blocked)
The gate has one or more broken axles or wheels.
The gate wheel is off the gate rail.
29
EMERGENCY MANUAL RELEASE
NOTE: Unplugging the AC transformer only, WILL NOT disable the battery power to the unit. To disable
ALL power to the operator, disconnect the main power disconnect plug from the control board.
IT
TY EX
SAFE
1
Press button ONCE to disconnect operator.
Manually Backdrive Gate
Pickets
EXIT SAFETY CENTER
R
CENTE
Push FIRMLY
from end of gate
to manually open.
DO NOT push the
gate from pickets,
they could bend!
Press to Disconnect
Press Again to Reset
2
Press button AGAIN to reset operator.
Gate can no longer be manually pushed to open.
30
Accessories
4 inch
5 inch
6 inch
6 inch
5 inch
4 inch
V-Groove Power Wheels Series
Brackets
Transmitters
Page 25
12 VDC Photo Sensor
Page 17
Part # AOMRON12V
18 Vac Transformer
Page 14
Part # APOW1
For more information about accessories:
www.chamberlain.com
Magnetic Locks
(Outdoor)
Page 19
Part # MG1300
Solar Panel
Page 14
Part # SOLAR3
Stop Buttton
Page 18
Part # AEXITP
UL Approved Round Sensing Edge
Page 16
Part # G65MGR20x
x = length (4, 5, 6 ,8 ft)
(e.g. G65MGR206 is 6 ft)
UL Approved Square Sensing Edge
Page 16
Part # G65MGS20x
x = length (4, 5, 6 ,8 ft)
(e.g. G65MGS204 is 4 ft)
3-Button Control Station
Page 18
Part # 02-103
Plug-In Loop Detectors
Page 20
Part # AELD
31
12 VDC External Loop Detectors
Page 21
Part # A23
Troubleshooting
The Gate Will Not Operate with Remote: The radio receiver LED on the control board remains “ON” when using the remote control.
Probable Causes:
1. Stuck remote control button.
2. The radio receiver has malfunctioned
in the “ON” position.
Solutions:
Unstick remote control button.
Cycle the power to the radio receiver.
The Gate Will Not Operate with Remote: The radio receiver LED on the control board remains “OFF” when using the remote control.
Solutions:
Get new remote control battery.
Cycle the power to the radio receiver. Remote control will need to
be reprogrammed, see page 25.
Check wiring between receiver and surge suppressor.
Reprogram remote control, see page 25.
Verify that remote control frequency is 315 MHz.
Measure the resistance between pin 12 and 13 on the surge
suppressor (see page 12), if the circuit “closes” when the radio
receiver is transmitting, replace the surge suppressor.
Probable Causes:
1. Remote control battery is dead.
2. The radio receiver has malfunctioned in the “OFF” position.
3. Radio receiver’s signal is not getting to gate operator.
4. Remote is not programmed correctly.
5. Remote is not on the same frequency as the radio receiver.
6. Blown surge suppressor.
32
TROUBLESHOOTING CONTINUED
EXIT
M/S
FAIL
CHARGE
OK
BATTERY
LOW
2.5
3
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
DEPT
D
EXIT
LOOP
LIMIT
OPEN
STRIKE
STR
OPEN
O
SAFETY
LOOP
LIMIT
CLOSE
RADIO
RA
CMD
C
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
SAFETY
M/S
LINK
ON
OPEN
SAFETY CENTER
PLUG-IN LOOPS
EXIT
CENTER
Gate Doesn’t Move: Only the Power and Charge OK LEDs remain
ON after processing a command.
(In Master/Second installation, check LEDs on both boards).
60
CLOSE STOP
SOR
OSE
OFF
SYSTEM ON
CLOSE
POWER
Solutions:
Check battery connection.
Replace 20 amp fuse.
Push reset button once.
W4
NC
MAGLOCK
COM
COM
NO
RESET
Probable Causes:
1. Battery not connected.
2. Blown motor fuse.
3. Operator in disconnect mode.
BATTERY
MOTOR
AC POWER
ROBO UL
ON
OFF
OFF
60
G
CHARGE
OK
BATTERY
LOW
MASTER
SECOND
ON
OFF
2.5
3
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
FIRE
D
DEPT
EXIT
LOOP
LIMIT
OPEN
STR
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
C
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
MOTOR
RUN
COMMAND
PROCESSED
OPEN
EXIT
M/S
FAIL
BIPART
CLOSE STOP
SAFETY
1. Set device to provide a
normally open (NO) dry contact
output.
2. Adjust for proper sensitivity.
3. Each Loop detector should
be set to a different frequency.
4. Align photo electric sensors.
Replace safety device.
M/S
LINK
ON
POSITIVE STOP
UL OPEN
SENSOR
UL ALARM
ENTRAPMENT
POSITIVE STOP
UL CLOSE
SENSOR
OPEN OPEN
LEFT RIGHT
SYSTEM ON
CENTER
B
M/S LINK
PLUG-IN LOOPS
SAFETY CENTER
Solutions:
Remove obstruction.
A
UL CONNECTOR
EXIT
CLOSE
POWER
W4
NC
MAGLOCK
COM
COM
NO
RESET
3. Defective safety device.
SENSOR SENSOR
OPEN CLOSE
Probable Causes:
1. Safety device is sensing an
obstruction.
2. Misadjusted safety device.
ALARM
Gate Doesn’t Move: Power and Charge OK LEDs are ON and one
or more Entrapment LEDs remain ON after processing a command.
(In Master/Second installation, check LEDs on both boards).
BATTERY
MOTOR
AC POWER
ROBO UL
G
OFF
60
CHARGE
OK
BATTERY
LOW
SECOND
ON
OFF
2.5
TIMER
DELAY
REVERSE
SENSOR
ALARM
SENSOR
0
MOTOR
RUN
COMMAND
PROCESSED
FIRE
DEPT
D
EXIT
LOOP
LIMIT
OPEN
STR
STRIKE
O
OPEN
SAFETY
LOOP
LIMIT
CLOSE
RA
RADIO
C
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
3-PUSH BUTTON STATION
EXIT
M/S
FAIL
3
BIPART
MASTER
OPEN
SAFETY
M/S
LINK
ON
POSITIVE STOP
ON
OFF
CLOSE STOP
SAFETY CENTER
33
UL OPEN
SENSOR
UL ALARM
ENTRAPMENT
OPEN OPEN
LEFT RIGHT
SYSTEM ON
CENTER
For technical support: 1-800-528-2806
UL CLOSE
SENSOR
PLUG-IN LOOPS
EXIT
Solutions:
Press reset button twice or
cycle power to operator.
B
M/S LINK
POSITIVE STOP
SENSOR SENSOR
OPEN CLOSE
Probable Causes:
Two consecutive entrapment
signals received at the board.
A
UL CONNECTOR
ALARM
Gate Doesn’t Move in the CLOSE Direction. Reverse Sensor or
Alarm Sensor LED is ON and/or the alarm has been set off.
(In Master/Second installation, check LEDs on both boards).
WIRING DIAGRAM • ROBOSLUL3™
Ground
Chassis
Robo-UL Surge Suppressor
Green
P/N 001C6064
Patent Pending
3 Black
–
G
B
A
M/S Link
4 Wires
A
OFF
60
SYSTEM ON
M/S
FAIL
CHARGE
OK
BATTERY
LOW
ON
TIMER
REVERSE
SENSOR
MASTER
SECOND
ON
OFF
2.5
3
Class 2
Supply
8 Black
12 Volts DC
0
J8
J7
ALARM
SENSOR
MOTOR
RUN
LIMIT
OPEN
LIMIT
CLOSE
RADIO
RA
CMD
CENTER
LOOP
LIMIT
ERROR
OPEN
STOP
CLOSE
1
2
3
4
5
6
J4
3-PUSH BUTTON STATION
EXIT
LOOP
SAFETY
LOOP
OPEN
FIRE
DEPT
D
STRIKE
ST
OPEN
O
J6
COM
COM
POWER
4 3 2 1
NC
NO
RESET
1
2
3
4
1
2
MAGLOCK
J12
Left
J11
W4
J15
2
2
1
1
Battery/Power
Harness
MOTOR
3
AC POWER
J14
4 Amp Fuse
20 Amp, 32 V Fuse
30 A Relay
18 Vac
Black
Black
30 A Relay
12 VDC
NO NC
Green
Ground Chassis
Reset Button
Note: See table on next page.
34
N.C.
Com
N.O.
Com
DC Motor
Input Power
120 Vac, 60 Hz
18 Vac Power
Transformer
NO NC
Com
Reset Switch Harness
Com
Motor Harness
Battery
+
Radio
Receiver
DELAY
CLOSE STOP
EXIT
Not Used
SAFETY
M/S
LINK
COMMAND
PROCESSED
4
BATTERY
Black –
10
9
8
7
6
5
4
3
2
1
G
1 BIPART
2 3
J1ROBO UL
Red +
Strike Open
Push Button
Radio Harness
ON
OFF
POSITIVE STOP
UL ALARM
ENTRAPMENT
J10
Limit Box Assy
UL OPEN
SENSOR
UL CLOSE
SENSOR
OPEN OPEN
LEFT RIGHT
Blue (To Left Limit Switch)
Red (To Left Limit Switch)
Yellow (To Right Limit Switch)
Purple (To Right Limit Switch)
NC
Yellow Com
Purple N.C.
Blue N.C.
Red Com
B
M/S LINK
PLUG-IN LOOPS
SAFETY CENTER
CENTER
Fire Dept
Key Switch
Green/Black
J5
UL CONNECTOR
SENSOR SENSOR EXIT
OPEN CLOSE
Right
J7
POSITIVE STOP
ALARM
Alarm
J9
Exit
Loop
3 Black Wires
8 Black Wires
1
2
3
4
5
6
7
6
5
4
3
2
1
J2
Safety
Loop
Green
White
Black
Red
Limit Harness
Center
Loop
WIRING DIAGRAM TABLE • ROBOSLUL3™
Robo-UL Control Board
J#
J Pin #
Signal Type
Direction
Level (+/- 10%)
Device Pin #
Device Connection
J1
J1
J1
J1
J2
J2
J2
J2
J2
J2
J2
J4
J4
J4
J4
J4
J4
J5
J5
J5
J6
J6
J6
J6
J7
J7
J7
J7
J7
J8
J8
J8
J8
J8
J8
J8
J8
J8
J8
J9
J9
J9
J9
J9
J9
J10
J11
J12
J14
J14
J15
J15
1
2
3
4
1
2
3
4
5
6
7
1
2
3
4
5
6
1
2
3
1
2
3
4
1
2
3
4
5
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
–
10 Pins
10 Pins
1
2
1
2
Input Power
Input Power
Battery –
Battery +
UL Alarm
Ground
Ground
UL Sensor Open
Ground
Ground
UL Sensor Close
Open
Ground
Stop
Ground
Close
Ground
Ground
Mstr/Second Comm
Mstr/Second Comm
Maglock Relay (NC)
Maglock Relay (Com)
Maglock Relay (Com)
Maglock Relay (NO)
Limit (Open)
Ground
Limit (Close)
Ground
N/C
Radio Power
Radio
Ground
Strike Open
Fire
Exit
Safety
Center Loop
N/C
N/C
Not Used
Not Used
Safety Loop Wire
Safety Loop Wire
Exit Loop Wire
Exit Loop Wire
Not Used
Safety Loop Detector
Exit Loop Detector
Motor (+/CCW, -/CW)
Motor (-/CCW, +/CW)
Reset Switch (Com)
Reset Switch (NC)
In
In
In
In
Out
In
In
In
In
In
In
In
In
In
In
In
In
In/Out
In/Out
In/Out
In
In
In
In
In
In
In
In
–
Out
In
In
In
In
In
In
In
In
–
–
–
In
In
In
In
–
In
In
Out
Out
In
In
18 Vac
18 Vac
0V
12 VDC
12 or 0 VDC
0V
0V
5 or 0 VDC
0V
0V
5 or 0 VDC
5 or 0 VDC
0V
5 or 0 VDC
0V
5 or 0 VDC
0V
0V
5 or 0 VDC
5 or 0 VDC
Dry
Dry
Dry
Dry
5 or 0 VDC
0V
5 or 0 VDC
0V
–
12 VDC
5 or 0 VDC
0V
5 or 0 VDC
5 or 0 VDC
5 or 0 VDC
5 or 0 VDC
5 or 0 VDC
–
–
–
–
2 to 10 VDC
2 to 10 VDC
2 to 10 VDC
2 to 10 VDC
–
5 or 0 VDC
5 or 0 VDC
12 or 0 VDC
12 or 0 VDC
Dry
Dry
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
G
B
A
–
–
–
–
–
–
–
–
–
13
12
2, 3, 5, 8, 10, 11
9
7
6
4
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
18 Vac
Transformer Input
Battery Input
Built-In Alarm Input
Entrapment
Protection Input
3 Button Control
Station/Stop
Button Input
Surge
Suppressor M/S
Link Input
Maglock/
Solenoid Input
Limit Switches
Input
Surge Suppressor
8 Wire Input
Plug-In
Loop
Plug-In
Loop Detector
Inputs
DC Motor Input
Reset Button Input
Note: See diagram on previous page.
35
Repair Parts
R E PA I R PA R T I L L U S T R AT I O N S
Q123
K17-33079
K16-51254
K19-25070
Q133
Q101*
Q131
Q132
K32-50225-15
Q032*
Q137
K13-51271
K29-50279
Q029*
ABT12
Q129*
312HM
K09-51246
K80-51260
02-51227
40
4
K24-33080
PLUG-IN LOOPS
CE
NT
ER
EX
IT
IN
K35-33081
SA
FE
TY
K-001A6055
K94-33082
Q006
K70-51061
APOW1
K41-51251
NOTE: * Sold Individually, 2 shown.
Parts list on next page.
36
HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION SPANS AMERICA. INSTALLATION AND SERVICE INFORMATION
IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER:
1-800-528-2806
HOURS: (Central Standard Time) 6:00 A.M. TO 7:00 P.M. - Monday through Friday, 8:00 A.M. TO 4:30 P.M. - Saturday
www.chamberlain.com
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART NAME
• MODEL NUMBER
Address orders to:
THE CHAMBERLAIN GROUP, INC.
Technical Support Group
6020 S. Country Club Road
Tucson, Arizona 85706
REPAIR PART NAMES AND NUMBERS
02-51227 - Switch, Push Button, Snap, 15A
SVC Kit, ROBOSL Pulleys - K17-33079
- Pulley, Multi-V, 3" OD, 1/2" Bore
- Pulley, Multi-V, 1.5" OD, 1/2" Bore
312HM - 12 V Radio Receiver
ABT12 - 12 VDC, 7.2 Amp. Battery
APOW1 - 18 Vac Transformer
SVC Kit, ROBOSL Relays - K24-33080
- Relay, 30 A, 12 VDC Coil, SPDT
- Relay, 30 A, 18 Vac Coil, SPDT
K-001A6055 - Robo-UL Control Board
K09-51246 - Chassis, RoboSLUL3
K10-50531 - Tray, Battery, RoboSlide
K10-50532 - Bracket, Battery Holder, ROBOSLUL3
SVC Kit, ROBO Fuses - K35-33081
- 4 Amp Fuse - Robo
- 20 Amp, 32 Volt Fuse - Robo
K13-51271 - Cover, Top, RoboSLUL
K16-51254 - V-Belt, Multi-V, 15" L, 150J4
K19-25070 - Chain, #25, 70 Pitch, RoboSLUL3
SVC Kit, ROBOSL Cables - K94-33082
- Assy, Harness, Lmt Sw, RoboULSL
- Assy, Harness, Motor, RoboSL-UL
- Assy, Harness, Power, RoboSL-UL
- Assy, Harness, Reset Switch, SL3K-E Kit
- Assy, Harness
- Assy, Cable, Receiver Inputs
- Harness, Reset Switch. RoboUL-SL
K29-50279 - Siren, Sealed
Idler Pulley Assembly - Q129
- Bushing, 7/8" OD, .120" Wall x 1.950"
- Pulley, Idler, Molded Plastic, SL
- Screw, Hex, 5/8-11 x 2 3/4", Grade 5
- Nut, Hex, Jam, 5/8 -, S/Z
- Washer, Flat, 5/8", SAE, S/Z
Q101 - Limit Switch Bearing Holder
K32-50225-15 - Gear Reducer, 15:1, #40, CSW/RoboUL
K41-51251 - Cover, Clear, Control Box, RoboSLUL3
K70-51061 - Robo-UL Surge Suppressor
K80-51260 - Hinge, Control Box, RobSLUL
Q006 - Standoff, Hex, F/F, 6-32 x 1.00" (1 Set)
Q029 - Switch, Limit, Sealed, W/Lever
Q032 - Limit Switch Adjustment Nut
Q123 - Motor, DC, 12V, 1/8HP, Base Mount
Q131 - Sprocket, #25, 23 Tooth, 5/8" Bore
Q132 - Sprocket, #25, 23 Tooth, 3/8" Bore
Q133 - Sprocket, #41, 30 Tooth, 5/8" Bore
Q137 - Limit Switch Box
Note: Assembly Parts Number
37
System Diagram
38
Installation Checklist
1. Owner and Installer must read all warnings and safety precautions. (Pages 2-7)
2. Make sure concrete mounting pad is big enough and deep enough for operator. (Page 10)
3. Operator must be securely fastened to concrete pad. (Page 10)
4. Operator chain must be 4 inch Minimum from gate. Chain must not be too tight or too loose. (Page 10)
5. Gate operator should be grounded to an earth ground rod within 3 feet. (Page 13)
6. Verify that both the battery and plug-in transformer are connected properly. Know where the main power disconnect plug
is to disconnect all power to operator. (Page 14)
7. Verify that the gate opens and closes as needed. (Page 22)
8. When gate hits object during operation, it must stop or reverse, depending on the direction gate is traveling. (Page 26)
9. Make sure that any pinch point or potential entrapment are guarded by means of safety devices or like. (Pages 5, 6, 16, 17)
10. Warning placards need to be permanently mounted on both sides of gate. (Page 7)
11. Test all additional equipment connected to operator.
12. Make sure all wire connections are securely fastened.
13. Review typical maintenance on operator. (Page 27)
14. Schedule periodic maintenance on operator by qualified service technician.
15. Inquire about Manufacturers “operator warranty”. (Warranty Card Included with operator)
16. Inquire about separate “installation warranty” with installer.
Installer Company Name, Address and Phone Number
Date of installation:
39
Warranty Policy
CHAMBERLAIN ELITE THREE YEAR LIMITED WARRANTY.
The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser of this product, for the structure in which this product is
originally installed, that it is free from defect in materials and/or workmanship for a period of three years from the date of purchase
[and that the ROBOSLUL3™ is free from defect in materials and/or workmanship for a period of three years from the date of purchase].
The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation,
maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.
If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806,
toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You
will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase
receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are
confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you
and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.
ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE THREE YEAR LIMITED
WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE ROBOSLUL3™, WHICH ARE
LIMITED IN DURATION TO THE THREE YEAR LIMITED WARRANTY PERIOD FOR THE ROBOSLUL3™], AND NO IMPLIED
WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some States do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE
CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO
PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT),
LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES.
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE,
INCLUDING BUT NOT LIMITED TO THE GATE CHAIN CONNECTION, GATE ALIGNMENT. THIS LIMITED WARRANTY ALSO DOES NOT
COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY
ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN
CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY.
NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.
Some States do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or
exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
See pages 36 and 37 for repair parts and how to order.
40
ROBOSLUL3™
845 Larch Avenue
Elmhurst, Illinois 60126-1196
© 2006, The Chamberlain Group, Inc. – All Rights Reserved
01-51265