User Guide
HDMI & DVI Extenders
DTP HDMI 230
HDMI Twisted Pair Extender
68-2244-01 Rev. B
06 13
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended
to alert the user of the presence of uninsulated dangerous voltage
within the product’s enclosure that may present a risk of electric
shock.
Chinese Simplified(简体中文)
警告:
产品上的这个标志意在警告用户该产品机壳内有暴露的危险
电压,有触电危险。
注 意:
ATTENTION: This symbol,
, when used on the product, is intended to alert the
user of important operating and maintenance (servicing) instructions in the
literature provided with the equipment.
产 品 上 的 这个 标 志 意 在 提 示用 户设 备 随 附 的 用 户手 册 中 有
重要的操作和维护(维修)说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 www.extron.cn,参见 Extron
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
安全规范指南,产品编号 68-290-01。
Instructions de sécurité • Français
Chinese Traditional(繁體中文)
AVERTISSEMENT: Ce pictogramme,
, lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier
du produit d’une tension électrique dangereuse susceptible de
provoquer un choc électrique.
警告:
若產品上使用此符號,是為了提醒使用者,產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意
ATTENTION: Ce pictogramme,
, lorsqu’il est utilisé sur le produit, signale à
l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se
trouvent dans la documentation fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron,
réf. 68-290-01, sur le site Extron, www.extron.fr.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol
auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol
auf dem Produkt soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur
Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie
in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.de.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo,
, cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro
del producto, lo que puede representar un riesgo de descarga
eléctrica.
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細
資訊,請瀏覽 Extron 網站:www.extron.cn,然後參閱《Extron 安全性與法規
遵守手冊》,準則編號 68-290-01。
Japanese
警告: この記号
が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意: この記号
が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの
注意を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
ついては、エクストロンのウェブサイト www.extron.jp より
『 Extron Safety and Regulatory Compliance Guide 』(P/N 68-290-01) をご覧ください。
Korean
경고: 이 기호
, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의:
ATENCIÓN: Este símbolo,
, cuando se utiliza en el producto, avisa al usuario
de la presencia de importantes instrucciones de uso y mantenimiento recogidas
en la documentación proporcionada con el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y
temas relacionados, consulte la Guía de cumplimiento de normativas
y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.es.
若產品上使用此符號,是為了提醒使用者。
이 기호
, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련
항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.co.kr)의
Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; correcting the interference is at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with unshielded twisted pair (UTP)
or shielded twisted pair (STP) cables; but, to ensure FCC Class A and CE compliance, STP
cables and STP Connectors are required.
For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility,
accessibility, and related topics, see the “Extron Safety and Regulatory Compliance
Guide” on the Extron website.
Specifications Availability
Product specification are available on the Extron website, www.extron.com.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: A caution indicates a situation that may result in minor injury.
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
Copyright
© 2013 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of
RGB Systems, Inc. or Extron Electronics:
Registered Trademarks (®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IP Intercom, IP Link,
Key Minder, LockIt, MediaLink, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System Integrator,
TeamWork, TouchLink, V‑Lock, VersaTools, VN‑Matrix, VoiceLift, WallVault, WindoWall
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks (™)
AAP, AFL (Accu‑Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto‑Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP
(Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel
Controller), Scope‑Trigger, SIS, Simple Instruction Set, Skew‑Free, SpeedNav, Triple‑Action Switching, XTP, XTP Systems, XTRA, ZipCaddy,
ZipClip
Contents
Introduction............................................................ 1
Reference Information....................................... 10
About this Guide.................................................. 1
About the DTP HDMI 230 Tx/Rx Transmitter
and Receiver...................................................... 1
TP Cable Advantages...................................... 2
Control Communications................................. 2
Features.............................................................. 2
Mounting the Transmitter or Receiver................. 10
Tabletop Use................................................. 10
Mounting kits................................................. 10
UL Rack-Mounting Guidelines....................... 11
Disconnecting the Ground................................. 11
Installation and Operation................................... 3
Mounting the Units.............................................. 3
Connections........................................................ 4
Transmitter Connections.................................. 4
Receiver Connections...................................... 5
Connector and Cable Details........................... 7
Operation............................................................ 9
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Table of Contents
v
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Introduction
vi
Introduction
•
About this Guide
•
About the DTP HDMI 230 Transmitter and Receiver
•
Features
About this Guide
This guide describes the Extron DTP HDMI 230 Long Distance High Definition Multimedia
Interface (HDMI) Twisted Pair Extender, which consists of a DTP HDMI 230 Tx transmitter
and a DTP HDMI 230 Rx receiver. This guide describes how to install, operate, and
configure the transmitter and receiver.
About the DTP HDMI 230 Tx/Rx Transmitter and Receiver
The Extron DTP HDMI 230 Tx/Rx transmitter and receiver pair (see figure 1) extends the
usable distance of HDMI digital video, optional analog audio, and bidirectional RS-232 and
infrared (IR) control signals over one Extron XTP DTP 24 shielded twisted pair (STP) cable
(recommended) or Category (CAT) 5e, CAT 6, or CAT 6a STP or unshielded twisted pair
(UTP) cable. The DTP HDMI 230 can also extend DVI video, which may include embedded
audio, with the appropriate adapters. The video, audio, and control signals can be
transmitted up to 230 feet (70 m).
VCR
DVD
DOC
CAM
P
LAPTO
PC
ON
OFF
Y
DISPLA
MUTE
N
SCREE
UP
N
SCREE
DOWN
Extron
DTP HDMI 230 Tx
TouchLink
Control
System
TCP/IP
Transmitter
®
100
INPUT
IR
RELAY
LINK
3
ACT
1
3
1
COM
RX
IPL
250
4
3
2
1
4
TX
2
1
2
R
4
2
3
P
ER
OV
K
LIN
RS
-23
SIG
Tx
TS
PU
IN
Rx
DT
IR
2
G
Tx
Rx
RS-232
T
DTP
OU
O
DI
AU
R
WE
PO
X
V
12 MA
A
0.7
CAT 5-Type Cable
up to 230' (70 m)
HDMI
FL
LOSE
OPEN/C
HDMI
PQLS
/ON
STANDBY
OFF
USB
Extron
DTP HDMI 230 Rx
Receiver
Blu-ray Player
O
S
UT AUDI R
TP
OU
K
LIN
L
HDMI
SIG
RS-232
R
WE
PO
X
V
12 MA
A
0.7
DTP
IN
Flat Panel Display
Figure 1.
Typical Transmitter and Receiver Application
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Introduction
1
The DTP HDMI 230 Tx/Rx units are housed in quarter rack width metal enclosures. They
can be set on a tabletop or mounted in a rack, under or through furniture. The receiver can
also be mounted on a projector bracket.
The transmitter is shipped with a single external desktop 12 VDC power supply that
accepts 100 to 240 VAC, 50-60 Hz input. A single power supply connected to either the
transmitter or the receiver can power both units through the TP cable that carries HDMI video.
TP Cable Advantages
Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial
or HDMI cable. These transmitter and receiver twisted pair (TP) products make cable runs
simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple,
quick, and economical.
NOTE:Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or
STP201 cable to link the transmitter and receiver. The DTP HDMI 230 Tx/Rx does not
work properly with these cables.
Control Communications
The RS-232 and IR communications are a passive pass-through only. The transmitter and
receiver do not generate or respond to the RS-232 and IR communication signals.
Features
Transmits single link HDMI signals over a single STP or UTP cable — Standard
twisted pair cables provide an economical, easily installed cable solution.
Long distance transmission — Extends video, audio, and control signals up to 230 feet
(70 m).
Supports Display Data Channel (DDC) transmission — The transmitter and receiver
pair fully supports long distance transmission of the DDC signals.
Control communications pass-through — Bidirectional RS-232 and IR control signals
can be transmitted alongside the HDMI signal, so that the remote display can be controlled
without the need for additional cabling.
Supports Consumer Electronics Control (CEC) signal transmission
1-inch high, quarter rack width, metal enclosures — With low profile enclosures, the
transmitter and receiver can be discreetly installed in locations such as behind a plasma or
LCD flat-panel display.
External 100 VAC to 240 VAC, 50-60 Hz, international power supply — One power
supply is included with the transmitter.
Remote powering of transmitter or receiver — Only one power supply is normally
necessary to power both devices.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Introduction
2
Installation and
Operation
This section describes the installation and the operation of the DTP HDMI 230 Tx/Rx
Extender, including:
•
Mounting the Units
•
Connections
•
Operation
Mounting the Units
Mounting instructions can be found in Mounting the Transmitter or Receiver on
page 10. Compatible optional hardware is listed on the Extron website (www.extron.com).
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• Avoid ground potential differences between the transmitter and receiver installation
sites, which can lead to equipment damage or a missing or unstable picture. If
a potential difference cannot be avoided, remove the ground connection between
the units and locally power both units (see Disconnecting the Ground on
page 11). In this configuration, the DTP HDMI 230 cannot extend analog audio
and each unit requires a local power supply.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
3
Connections
Transmitter Connections
DTP HDMI 230 Tx Rear Panel
POWER
12V
0.7A MAX
5
INPUTS
2
Figure 2.
SIG
LINK
AUDIO
OVER DTP
RS-232
IR
DTP OUT
Tx Rx G Tx Rx
4
3
1
DTP HDMI 230 Tx Connectors
a HDMI input connector — Connect an HDMI cable between this port and the HDMI
output port (or DVI port, with an appropriate adapter) of the digital video source.
b Audio input connector — If desired, plug an analog audio input into the transmitter
via this stereo mini jack connector.
NOTE: The analog audio input on this connector is in
addition to the digital audio that may be embedded
in the HDMI input. See the figure at right to identify
the connector tip, ring, and sleeve when you
are making connections for the transmitter from
existing audio cables. A mono audio connector
consists of the tip and sleeve. A stereo audio
connector consists of the tip, ring, and sleeve.
Tip (+)
Ring (-)
Sleeve ( )
3.5 mm Stereo Plug Connector
(balanced)
c RS-232 and IR connector — Connect a serial RS-232 signal, a modulated IR
signal, or both to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232
and IR communication (see RS-232 and IR connector wiring on page 9 to wire the
connector).
d DTP Output RJ-45 connector — Connect one end of a TP cable to this RJ-45
female connector on the transmitter. Ensure the opposite end of this cable is connected
to the receiver DTP Input RJ-45 connector (see item f on the next page).
ATTENTION: Do not connect this device to a telecommunications or computer
data network.
NOTE:See TP cable termination and recommendations on page 7 to properly
wire the RJ-45 connectors and for detailed NOTES.
Signal LED — Indicates the unit is receiving a TMDS clock signal on the HDMI input.
Link LED — Indicates a valid link is established between the units on the DTP input
and output cable.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
4
e Power input connector — Plug the included external 12 VDC power supply into
either this 2-pole connector or the power input connector on the receiver (item j on
page 6). See Power supply wiring on page 8 to wire the connector.
NOTES:
• One power supply is included with the transmitter and normally can power
both units.
• If you have removed the ground jumpers (see Disconnecting the Ground
on page 11) because of ground potential differences, one DTP HDMI 230
unit cannot remotely power the other unit. Each unit requires a local power
supply.
Receiver Connections
Front Panel
DTP HDMI 230 Rx Rear Panel
SIG
LINK
OUTPUTS
POWER
12V
0.7A MAX
L
AUDIO
OVER DTP
R
DTP IN
10
RS-232
IR
Tx Rx G Tx Rx
6
7
Figure 3.
8
DTP HDMI 230 Rx
9
DTP HDMI 230 Rx Connectors
f DTP Input RJ-45 connector — Connect one end of the TP cable from the transmitter
output connector to this RJ-45 female connector. Ensure the opposite end of this
cable is connected to the transmitter DTP Output RJ-45 connector (see item d on the
previous page).
ATTENTION: Do not connect this device to a telecommunications or computer
data network.
NOTE:See TP cable termination and recommendations on page 7 to properly
wire the RJ-45 connectors and for detailed NOTES.
Signal LED — Indicates the unit is receiving a valid signal on the DTP In connector.
Link LED — Indicates a valid link is established between the units on the DTP input
and output cable.
g HDMI output connector — Connect a display with an HDMI input port (or DVI input
port, with an appropriate adapter) to display the transmitted direct digital image.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
5
h Audio output connector — This 5-pole, 3.5 mm captive screw connector outputs
the transmitted, unamplified, line level analog audio. Connect an audio device, such as
an audio amplifier or powered speakers.
See figure 4 to properly wire a captive screw output connector. Use the supplied
tie-wrap to strap the audio cable to the extended tail of the connector.
NO GROUND HERE
Tip
Ring
R
Figure 4.
L
Unbalanced Stereo Output
Tip
Ring
R
NO GROUND HERE
L
Do not tin the wires!
Tip
Sleeves
Tip
Balanced Stereo Output
Captive Screw Connector Wiring for Stereo Audio Output
ATTENTION: For unbalanced audio, connect the sleeves to the ground contact.
Do not connect the sleeves to the negative (-) contacts.
NOTES:
• If you have removed the ground jumpers (see Disconnecting the Ground on
page 11) because of ground potential differences, the DTP HDMI 230 cannot
extend analog audio. No analog audio is output.
• The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).
• If the stripped section of wire is longer than 3/16 inch, the exposed wires
may touch, causing a short circuit.
• If the stripped section of wire is shorter than 3/16 inch, wires can be easily
pulled out even if tightly fastened by the captive screws.
• Do not tin the power supply leads before installing them in the connector.
Tinned wires are not as secure in the connector and could be pulled out.
i RS-232 and IR connector — Connect a serial RS-232 signal, a modulated IR
signal, or both to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232
and IR communication (see RS-232 and IR connector wiring on page 9 to wire the
connector).
j Power input connector — Plug the included external 12 VDC power supply into
either this 2-pole connector or the power input connector on the transmitter (see
item e on the previous page) (see Power supply wiring on page 8 to wire the
connector).
NOTES:
• One power supply is included with the transmitter and normally can power
both units.
• If you have removed the ground jumpers (see Disconnecting the Ground
on page 11) because of ground potential differences, one DTP HDMI 230
unit cannot remotely power the other unit. Each unit requires a local power
supply.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
6
Connector and Cable Details
TP cable termination and recommendations
Figure 5 details the TIA/EIA T 568B wiring standard. Use this standard to terminate TP
cables with RJ-45 connectors.
Side
Pins:
RJ-45
Connector
12345678
TIA/EIA T
568 B
Wire color
Pin
Insert
Twisted
Pair Wires
Figure 5.
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
TP Cable Termination
NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the transmitter and receiver. The DTP HDMI 230 Tx/Rx does not work
properly with these cables.
Supported cables —
The DTP HDMI 230 is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair (F/UTP,
SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable.
Cable recommendations —
Extron recommends using the following practices to achieve full transmission distances up
to 230 feet (70 m) and reduce transmission errors.
•
Use the following Extron XTP DTP 24 SF/UTP cables and DTP 24 connectors for the
best performance:
•
XTP DTP 24/1000
•
XTP DTP 24P/1000 Plenum 1000’ (305 m) spool
22-235-03
•
XTP DTP 24 Plug
101-005-02
Non-Plenum 1000’ (305 m) spool
Package of 10
22-236-03
•
If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
•
Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
•
Use no more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are
required, use CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: When using CAT5e and CAT6 cable in bundles or conduits, consider the
following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or Velcro®.
• Separate twisted pair cables from AC power cables.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
7
Power supply wiring
NOTES:
• One power supply is included with the transmitter and normally can power both
units.
• If you have removed the ground jumpers (see Disconnecting the Ground on
page 11) because of ground potential differences, one DTP HDMI 230 unit cannot
remotely power the other unit. Each unit requires a local power supply.
Figure 6 shows how to wire the connector. Use the supplied tie-wrap to strap the power
cord to the extended tail of the connector.
Smooth
Ridges
A
A
SECTION A–A
Power Supply
Output Cord
Tie Wrap
3
Figure 6.
Power Connector Wiring
CAUTION: Electric shock hazard —
5
Captive Screw
Connector
• The two power cord wires must be kept separate while the power supply is
plugged in. Remove power before wiring.
• The length and preparation of exposed wires is important (see the second and
third audio connector NOTES on page 6 for details).
ATTENTION:
• This product is intended to be supplied by a Listed Power Unit marked “Class 2”
or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply supplied by
or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air
handling spaces or in wall cavities.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to a
building structure or similar structure.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord (see figure 6) identify
the power cord negative lead.
To verify the polarity before connection, plug in the power supply with no load and check the
output with a voltmeter.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
8
RS-232 and IR connector wiring
Figure 7 shows how to wire the RS-232 connector.
IR Device
Rx Tx Gnd
Tx Rx
Tx Rx
G
IR
RS-232
Tx/Rx
Pins
Tx Rx Gnd
RS-232 Device
Figure 7.
RS-232 Connector Wiring
NOTES:
• The IR Tx and Rx line pair and the RS-232 Tx and Rx line pair must each cross
once between this connector and the source or destination.
• The length and preparation of exposed wires is important (see the second and
third audio connector NOTES on page 6 for details).
Operation
Figure 8 shows the location of the power indicators on the front and rear panels of the
transmitter and receiver.
Front Panel
Rear Panel
POWER
12V
0.6 A MAX
1
Figure 8.
2
Power Indicators
a Power (and signal) LED (front panel) —
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is receiving an active HDMI input, either on the HDMI input if a
transmitter, or transmitted on the DTP cable if a receiver.
b Power LED (rear panel) —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
After the transmitter, the receiver, and their connected devices are powered up, the system is
fully operational. If any problems are encountered, ensure all cables are routed and
connected properly.
NOTE: Ensure that the video source and display selected for the DDC are properly
connected to the transmitter and receiver pair, and that the transmitter, the receiver,
and the display have power applied before power is applied to the video source.
If the other devices are not turned on before the video source, the image may not
appear.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation
9
Reference
Information
This section provides procedures for mounting the DTP HDMI 230 Tx/Rx transmitter and
receiver and disconnecting the ground between them.
•
Mounting the Transmitter or Receiver
•
Disconnecting the Ground
Mounting the Transmitter or Receiver
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• Avoid ground potential differences between the transmitter and receiver installation
sites, which can lead to equipment damage or a missing or unstable picture. If
a potential difference cannot be avoided, remove the ground connection between
the units and locally power both units (see Disconnecting the Ground on the
next page).
The 1-inch high, quarter rack width DTP HDMI 230 transmitter or receiver can be placed
on a table, mounted in a rack, or mounted under a desk or table. The receiver can also be
mounted on a projector bracket.
Tabletop Use
Affix the included rubber feet to the bottom of the unit and place it in any convenient
location.
Mounting kits
Mount the unit using any optional compatible mounting kit listed on the Extron website
(www.extron.com), in accordance with the directions included with the kit. For rack
mounting, see UL Rack-Mounting Guidelines on the next page.
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Reference Information
10
UL Rack-Mounting Guidelines
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
unit into a rack.
•
Elevated operating ambient temperature — If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient. Therefore, consider installing the equipment in an environment
compatible with the maximum ambient temperature (TMA = +122 °F, +50 °C) specified
by Extron.
•
Reduced air flow — Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
•
Mechanical loading — Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
•
Circuit overloading — Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might have
on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
•
Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply connections other
than direct connections to the branch circuit (such as use of power strips).
Disconnecting the Ground
If you cannot resolve a ground potential difference between the transmitter and receiver
installation sites (as suggested by a missing or unstable picture), remove the ground
connection between the units as follows:
NOTE:Once you have removed the ground jumpers, the DTP HDMI 230 cannot
extend analog audio and one unit cannot remotely power the other. No analog audio
is output and each unit requires a local power supply.
1. Disconnect any cables and remove the transmitter and receiver from any rack or other
installation option.
2. Remove and retain the screws securing the covers to the transmitter and receiver. Slide
the covers forward slightly and lift them off both units (see figure 9).
•
Transmitter — Six screws, two on each side and two on top
•
Receiver — Eight screws, three on each side and two on top
Transmitter
Figure 9.
Cover Screws
(6 Plcs)
Cover Screws
(8 Plcs)
Rear Panel
Rear Panel
Receiver
Opening the Transmitter and Receiver
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Reference Information
11
3. Locate, lift off, and discard jumpers JMP2 and JMP3 from both units (see figure 10).
JMP3, JMP2
JMP2
JMP3
Transmitter
Receiver
Figure 10. Jumper Locations
4. Reinstall the covers on both units, securing them in place with the screws removed in
step 2.
5. Reinstall both units in their racks or other installation option (see Mounting the
Transmitter and Receiver on page 10).
6. If you are using shielded cable, disconnect the cable shield from the connector at
either end of the cable.
7. Obtain a second 12 V power supply (one supply is provided with the transmitter and
normally powers both units), and locally power both units (see Power supply wiring
on page 8).
DTP HDMI 230 Tx/Rx Transmitter and Receiver • Reference Information
12
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe and Africa:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876
Asia:65.6383.4400
Europe:31.33.453.4040
Japan:81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX