Controls
Controls Diagram
Product Contents
RP-SMA*2
Channel/Band Selection
Turn on/off OSD
Eachine EV100
Goggles *1 Mode/Brightness/Contrast
To check battery level
Eachine EV100
NEW 5.8G FPV Goggles
Battery*1
Focal Length Adjustment
Mode/Brightness/Contrast control
Mode : a.Debug mode: Press "mode" button and
power on, enter debug mode (5300MHz).
b.Racing mode:Long press "mode" button until first beep
to switch mode from 4 pilots/6 pilots/8 pilots. For example:
4 pilots/6 pilots/8 pilots/exit racing mode switching circularly.
c.Auto search: Long press "mode" button until second beep
to enter auto search.
d.Turn on/off RX: Long press "mode" button until third beep
to enter AV IN (RX OFF).
Thumbwheel is used to adjust focal length.
(+) means to increase diopter, (-) means to
decrease diopter.
AV IN
Antenna*2
1
3.5mm Headphone jack
USB charging port
USB data cable*1
SMA*2
IPD adjustment
Lenswiping cloth*1
Power supply
Eachine EV100
NEW 5.8G FPV Goggles
User Manuals*1
White/Black
3.5mm AV in/out
White/Black
User Manuals
User Manuals
fan on/off
Focal length adjustment
Battery
Ground
3.5mm AV Connector
Video
AudR
AuL
AV input & output
Support external HDMI to AV input
Support external DVR.
Li-Po BATTERY PACK
Battery charging
▪For firmware upgrading.
▪Alternative power supply.
If multiple power sources are supplied at same time
(Like: power Bank and head strap battery)the goggles
will draw power from the highest voltage.
Mode
In this mode, the best results can be achieved
by using the supporting vtx.
Racing Mode
Charge max rate of 1C(DC connector)
USB charging with approved adapter
( USB:5V==1.5A or 2A)
It is not recommended to charge the battery
via PC USB, since the insufficient current will
damagethe battery.
WARNING
Do not open the battery case
Never leave batteries near fire or
high temperatures
Battery may balloon or catch fire if faulty
or improperly charged
Never leave a charging battery unattended
Do not use if signs of failure
3 Racing Mode: 4/6/8 pilots
60-80MHz interval between adjacent channels
greatly decrease interference.
Snap joint assemblies allows easy
replacement and maintenance
Replaceable sponge
Patch
Velcro
Sponge
Flannel
Debug Mode
Press "mode" button first and then powering on
goggles, enter debug mode (5300MHz). Requires
a corresponding vtx which support pitmode and
extra frequency 5300MHz.
5
Using Velcro as a bridge, sponge and flannel
can be easily replaced, and Velcro can be
used for a long time.
6
4
Band & Frequency table
7
Trouble Shooting
Unit:MHZ
28°Diagonal
Plastic optic module
Band CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
Band ━A 5865 5845 5825 5805 5785 5765 5745 5725
58 to 68 mm (adjustable)
Under 400 degree of myopia and
Hyperopia 100 degree (adjustable)
Band ━b 5733 5752 5771 5790 5809 5828 5847 5866
Resolution : 720*540
NTCS/PAL auto selecting
Channel/Band selection
User Controls:
Mode selection (debug/racer)
Contrast/ brightness control
Turn on/off RX/fan/OSD
Battery:
7.4V,1000mAh Li-po battery with
LED indicator
Can power the external DVR
Interface:
3.5mm AV in/out port
Power in port
3.5mm stereo earphone port
USB in port
Accessories:
Lens wiping cloth
USB data cable
5.8G RP-SMA male antenna*2
7.4V, 1000mAh Li-po battery with
LED indicator
Operation temperature :
-10c°-40c°
5.8GHZ 5333—5945MHZ
Frequency:
≤-93DB
Sensitivity:
Dimensions:
165*76*30mm
Band━F 5740 5760 5780 5800 5820 5840 5860 5880
Display:
Made in china
Slider is switch to adjust IPD. (+) means to
increase IPD,(-)means to decrease IPD.
3
FOV:
Type:
IPD:
Focal length :
7.4V 1000mAh(7.4Wh) with LED indicator
(One charging indicator light, one
power-checking button and four
power indicator lights)
Independent control for both sides,adjust the range
of 58 ~ 68mm.
Channel/Band select
Channel: short Press channel up/down buttons will cause
the channel to incrementallyincrease/decrease from
channels 1 to 8 (refer to frequency table).
Band : Press channel up/down buttons 3s will cause
the band to incrementallyincrease/decrease from band
A to H (refer to frequency table).
Turn on/off OSD: Press channel up/down buttons
simultaneously to turn on/off OSD.
Low battery warning: Buzzer warning if input voltage
drops below 6.8V.
Turn on/off fan
Product specifications
Detachable Patch
It can simultaneously power the external DVR.
USB In
IPD Adjustment
AV IN display
Brightness: Pressing forward/back increases/decreases
display brightness.(32 level contrast for the LCD display, default level 28)
Contrast: Pressing left/right decreases/increases
display contrast.(32 level contrast for the LCD display, default level 28)
2
1
AV In/Out
72
Auto search display
USB in
Adjustable focal length is perfect for myope under 400
degree and hyperope under 100 degree.
Weight(not included battery):
Packaging:
8
180g
Band━E 5705 5685 5665 5645 5885 5905 5925 5945
Band━r 5658 5695 5732 5769 5806 5843 5880 5917
Band━U 5325 5348 5366 5384 5402 5420 5438 5456
Band━o 5474 5492 5510 5528 5546 5564 5582 5600
Band━L 5333 5373 5413 5453 5493 5533 5573 5613
Band━H 5653 5693 5733 5773 5813 5853 5893 5933
No image, display is completelydark
▪No power supplied. Check power connections.
No image, display is glowingdark grey
▪If using wireless module, ensure RX is working.
▪If using AV in cable, check video source.
▪Ensure TX is on and camera connections solid
▪Ensure lens cap is removed from camera
Complete white screen
▪LCD driver has failed and needs to be replaced under
warranty. Contact your retailer.
Short range
Racing mode frequency
▪Ensure 5.8Ghz antenna were installed.
4 pilots 5695 5769 5843 5917
6 pilots 5533 5613 5705 5785 5865 5945
8 pilots 5528 5582 5645 5705 5765 5825 5885 5945
OSD display
Regular mode:
Display values like: Band-r CH1 5658MHz
(refer to frequency table)
Racing mode:
Status description
Mode
235*120*70mm
9
157G铜版纸⿊⽩正反印刷折页
折叠尺⼨:110*70mm
展开尺⼨:420*110mm
10