Fully Automatic Coffee Machine
OPERATION MANUAL
Instructions of coffee machine parts
4
5
9
1
6
9
10
11
2
12
7
13
8
3
1
Bean container
2
Water tank
9
Milk pipe
3
Coffee grounds container
10
Milk frother
4
8
Waste water container
Pre - ground coffee chute
11
Hot water spout
5
Grinding wheel
12
Milk and foam spout
6
Coffee spout
13
Power cord
7
Handle
Coffee machine operation interface instructions
5
6
1
2
7
3
8
4
9
10
1
Espresso icon
6
Cappuccino icon
2
Long coffee icon
7
Coffee Latte icon
3
Hot water icon
8
Hot milk/foam icon
4
Power switch
9
Cleaning button
5
Display
10
Rotary button
Safety Instructions
Please see specification label on the bottom of the coffee machine or
technical date indicated in the instruction manual(P20).
IMPORTANT SAFEGUARDS
01
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all Instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse cord,
plugs, or (state specific part or parts in question) in water or other liquid.
4. Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
5.Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or if the appliance
malfunctions, or has been damaged in any manner. Return the appliance to the near
est authorized service facility for examination, repair or adjustment.
7. The use of accessory attachments not recommended by the appliance manufac
turer may result in fire, electric shock or injury to persons.
8. Do not use outdoors .
9. Do not let the cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always plug cord into the wall outlet first,then turn controls to "on". To disconnect,
turn any control to”off“, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. Check bean hopper for presence of foreign objects before using the brewer .
14. Unplug power cord from outlet before cleaning brewer exterior. Allow to cool
before disassembling and cleaning the coffee machine.
15. When dispensing drinks high temperature liquid will flow from coffee spout and hot
water spout. Do not touch hot liquids to avoid scalding
16. When using cappuccino, coffee latte, hot milk/foam, please confirm that the milk
pipe has been connected from the milk frother to milk before making cappuccino,
coffee latte, and hot milk/cream. Otherwise, high temperature steam may cause
personal injury.
17. Never connect to voltage different than the electric specification of the machine;
Brewer damage will occur.
18. Only potable water at room temperature should be used in the water tank.
Never put warm water, hot water, milk or other liquid into the tank.
Safety Instructions
19. Never carry or move the coffee machine while power is on.
20. The machine will release heat and some steam. Therefore, when placing the
machine on a workbench, at least 3cm must be left between its surfaces, sides and
rear; at least15cm must be left above its top.
As for dimension of the machine, please look up the Technical Data in the User
Manual(Page 20).
21. Never use harsh or abrasive cleaner to wipe the machine, it may cause
corrosion of the coffee machine, and result in a risk of electric shock.
22. Never use hard edged tool or rough rag to clean the stain on the machine, it will
damage the surfaces.
23. Never fill specially treated coffee beans (e.g. cocoa, sugar coated) into the
beancontainer, it will cause the coffee machine damage .
24. Only roasted coffee bean are approved to place into the bean container. Rice,
soybean, chocolate bean, nut, sugar, spice etc are prohibited. Otherwise it would
cause the coffee machine to be damaged.
25. Never wash the bean container or pre-ground coffee chute with water, it will
damage the machine.
26. Never use the coffee machine in the environment temperature below 0 °C.
Water inside the machine will freeze and cause the coffee machine damaged.
27. Never expose the machine in rainy, snowy, frosty environment. It would cause
the coffee machine to be damaged.
28. Save these Instructions.
02
POWER CORD EXTENSION USE
Please don’t use power cord extensions.
-
-
Proper operation
To guarantee the coffee taste, make sure that the temperature of the water poured
into the water tank is at room temperature.
The coffee machine can only be used for preparing coffee and hot water. Do not
use it for any other intended use. We will not be responsible for the consequences
of improper use. Please carefully read all the contents of
this manual, so that you can understand operation of the coffee machine
sufficiently.
Please keep this manual in an appropriate place to be accessed at any time.
Safety Tips
03
Please notice the following tips to avoid personal injury from electric shock.
Do not operate the coffee machine if the appliance or the power cord is
damaged.
When encountering a breakdown of the machine (if any burning smell or
smoke), unplug the power cord immediately and contact an authorized
service center.
If the power cord of the coffee machine is damaged, please contact an
authorized service center.
Place the coffee machine and the power cord far away from heat sources.
Please don't contact the power cord with sharp tools.Do not repair the
coffee machine without authorization or operate it in anyway that is not
mentioned in this manual, to avoid personal injury.
Place the coffee machine out of the reach of children.
When the Coffee machine is unused for long periods, unplug the power
cord and put it away, so that not to trip up people or damage to the power
cord.
Please don't use unoriginal parts, otherwise, it may cause the machine to
be damaged.
Instructions for use
Reading this manual will help you familiarize yourself with the coffee
machine, and enable you to use it properly.
“Instruction for first-time use " introduces the operation process of the
coffee machine step-by-step, for first-time use.
“Failures handling" will provide information when encountering problems.
Coffee machine model
This Manual is only applicable to the 1601pro series coffee machine.
Symbol description
Non-compliance with proper operation, may cause electric shock,
and threat to life.
Non-compliance with proper operation may cause Coffee machine
damage, or personal injury.
Non-compliance with proper operation, may cause scalding or burn
injury.This symbol, if prompted, please carefully read it.
This symbol, if prompted, represents recyclable.
Catalogue
Safety Instructions
01
Proper operation
03
Instructions for use
03
Coffee machine model
Symbol description
Instructions for first time use
03
03
05
Power connection
05
Fill water tank
05
Fill beans
05
Grinding wheel
05
Power on
06
Power off
Making beverages
Preparing coffee by touch icon
Adjusting coffee parameters during a brew cycle.
Preparing coffee with pre-ground coffee
Program setting
Beverage setting
Setting beverage parameters and range
Temperature setting
Eco-settings
06
07
07
08
09
9
10
10
10
11
Automatic power-down
11
Factory Reset
11
Information Statics
11
Language
11
Exit
Cleaning and maintenance
11
12
Cleaning the coffee machine before operation
12
Cleaning brewing unit
12
Rinsing milk unit
13
Descaling the coffee machine
14
Cleaning coffee grounds container and drip tray
16
Cleaning water tank
17
Cleaning bean hopper
Disassembling and cleaning the milk frother
17
17
Installing milk pipe
17
Cleaning milk pipe
17
Cleaning coffee machine
18
Failures handling
18
Display information
19
Transport and recycle
20
Technical data
20
04
Instructions for first-time use
This chapter will help you understand the basic operations and settings for your
first time use
Power connection
● Place the coffee machine on a stable workbench that is not
close to water.
● Keep the coffee machine far away from high temperature
heat sources.
● Be sure to use the power supply that is in accordance with
specification label.
● Put the power cord at a suitable place to avoid people
tripping over the cord.
Fill water tank
● Only potable water at room temperature is allowed to be
poured in the water tank, never fill any other liquid (e.g.
warm water,hot water, milk). It will damage the coffee
machine. In order to ensure the taste of coffee, it is
recommended to use water at 25℃ . Low temperature
water will not create a good
taste.
● To ensure a healthy and the tasty coffee drink, please
change the water in the tank every day.
● The amount of water in the water tank cannot exceed the
height of the MAX mark.
Fill beans
05
● Never put coffee beans that have been specially
treated (e.g. sugar, cocoa) into the bean hopper.
● Only roasted coffee beans can be put into the bean hopper,
never put other items like rice, soybeans, chocolate beans,
nuts,sugar, and spices into the hopper.
● Never put hard objects into the beanhopper, otherwise it will
damage the grinder.
● The bean hopper cover acts as a seal. It keeps the aroma
of coffee beans maximized. Please do not lose the cover.
● Don't pour liquid in the bean container.
Finest
Grinding wheel
● Please adjust the fineness of coffee bean grind choice
according to the coffee bean type.
● Please adjust the grinding wheel when the grinder is running,
or the grinder may be damaged.
● If your coffee beans are dark in color, it is recommended to
set to the coarse grind.
● If your coffee beans are light in color, it is recommended
to set to the fine grind.
● While making coffee drinks, if the coffee brew dispense
very slowly , please change the grind choice to a more
coarse grind.
● Adjust grind choice as needed, increase or decrease grind
level.
● The adjustment of grinding wheel will be effective only after
making two or more cups of coffee.
Fine
Medium
Coarse
Coarsest
First-time use
Power on
● As the machine has been tested at the factory, there may
be a little coffee left in the machine .
● The coffee machine will start self-testing and cleaning upon
first-time use, this helps the coffee machine achieve the
best working condition, and this process cannot be skipped
● When powering on the coffee machine, it will automatically
complete heating and cleaning for one time, every
time and the process cannot be stopped. The coffee machine
can only be used after the above cycle process is finished.
● During the cleaning process, some hot water may flow out of
the coffee spout into the drip tray. Please avoid contacting
the hot water.
Please ensure the power is connected before pressing
the power button.
Power off
● When powering off the coffee machine , it will automatically
complete the cleaning process for one time, every time,and the
process cannot be stopped. This operation is to clean up
the coffee pipelines and remove the coffee grounds.
● During the cleaning process, some hot water will flow out of
the coffee spout into the drip tray. Avoid touching hot
water, so as not to be burned.
Only after using milk/foam/cappuccino/latte, the Rinse
Milk Unit function will be operated when the power is turned off.
● When you press the power button, the machine will be
powered off after auto cleaning
When you press
the power button, the machine will be
powered off after auto cleaning.
READY
06
Making beverages
T,his chapter instructs you on how to make various kinds
of coffee, hot water,hot milk and milk foam by this coffee
machine.Please read the following instructions carefully to help
you make high-quality beverages
The temperature of the hot water is high, please do not touch it to
avoid being scalded.
Before making all kinds of coffee, please ensure “READY” is indicated
on the display.
● The coffee beans should be stored in a dry place and avoid sunlight.
● Only potable water at normal temperature can be used. To make the
coffee tastes better, it is recommended to use water around25℃.
● To ensure the quality of coffee, please change the water in the water
tank every day.
● Please warm the coffee cup before making the coffee for better
taste.
● Please adjust the height of the coffee spout according to the
height of the cup in order to avoid coffee splashing.
● Adjustable height of coffee spout: 80-140mm.
Preparing coffee by touch icon
You can make 4 kinds of coffee using the touch icons, when the screen
shows
“READY”
07
Take espresso for example to explain how to make coffee by touch icons.
The volume of espresso is suggested between 30 to 50ml.
Because of the small volume of espresso, please warm the coffee cup before
making coffee.
READY
Touch the espresso icon for espresso
function.
ESPRESSO
STRONG
VOLUME
50ML
The grinder will begin to grind . At this time
you can adjust the amount of coffee beans
by rotating the rotary button.
Default amount of coffee beans for
espresso:
During making coffee, you can adjust the
volume of coffee by rotating the rotary
button.
Default volume of espresso: 50ML
When the screen shows as the left picture, it
means the espresso is ready, please enjoy
it.
ENJOY !
ESPRESSO
Making beverages
Single time setting of coffee parameters
Adjusting coffee parameters during a brew cycle.
●
●
●
●
●
●
●
●
Set the amount of coffee beans during the grinding process.
Set the volume of coffee when making coffee
Set the dispense time of milk foam to control the volume when making cappuccino
Set the dispense time of milk to control the volume when making latte
Set the temperature of hot water before making hot water
Set the hot water volume when making hot water
Set the dispense time of hot milk to control the volume when making hot milk
Set the dispense time of hot foam when making hot foam
Detail instructions
You can set the strength of coffee before making the beverage and the
volume of the beverage during the brew cycle. The settings will not be
saved.
STRONG
When grinding the coffee beans, you can
rotate the rotary button to adjust the amount of
coffee beans, to the left is mild
the right is strong
, and to
. The default
amount is normal
VOLUME
FOAM TIME
MILK TIME
40ML
20S
15S
NORMAL
VOLUME
60ML
When making long coffee, coffee volume
can be adjusted by using the rotary button.
For example, the current volume is 100ml,
2 clicks to the left to reduce to 95ml, and 2
clicks to the right to increase to 105ml.
When making cappuccino, milk foam or
coffee latte,the foam making time can be
adjusted by rotating the rotary button while
the milk foam outflows. For example,the
current time is 20s,2 clicks to the left to
reduce to 19S,and 2 clicks to the right to
increase to 21S.
When making hot milk or coffee latte, milk
dispensing time can be adjusted by rotating
the rotary button. For example, the current
milk dispensing time is 15S, 2 clicks to the
left to reduce to 14S, and 2 clicks to the right
to increase to 16S.
Before making hot water, the temperature can
be adjusted by rotating the rotary button. To
the left is low, to the right is high. The default
temperature is normal.
When dispensing hot water, the hot water
volume can be adjusted by rotating the
rotary button.For example, the current
volume is 100ML, 2clicks to the left to reduce
to 95ML, and 2 clicks to the right to increase
to 105ML.
08
Making beverages
Preparing coffee with pre-ground coffee
You can choose this function if you want to make coffee with
Pre-ground coffee.
●Do not use instant coffee powder or cocoa powder in the
pre-ground coffee chute. powder container.Otherwise it will
damage the machine.
● Do not put pre-ground coffee powder into the coffee
bean hopper,otherwise, it will damage the machine.
● Please use proper Pre-ground coffee for espresso.
● Only 7-14g of pre-ground coffee can be added.
Machine will be damaged.
● The process of using pre-ground coffee to make coffee
only skips the process of grinding coffee beans, other
operations are the same as making espresso, long coffee,
cappuccino, and coffee latte. This chapter illustrates with
espresso.
READY
Press and hold the rotary button to
enter into programming when the
coffee machine is
“READY”.
09
GROUND COFFEE
Display shows “GROUND COFFEE ” page
after entered into programming. Press
the rotary button to make coffee.
Open pre-ground coffee chute cover and
fill .close the cover. Touch the
FILL GROUND COFFEE
beverage icon you need to make coffee.
Press the rotary button to cancel.
SELECT COFFEE
ROTARY TO CANCEL
Program setting
● This chapter will give instructions on program settings.
● Ensure the coffee machine shows “READY”, press and hold the
rotary button , then you can enter into the menu
Beverage setting
This chapter will instruct you how to set beverages parameters. The
settings parameters include coffee strength, volume of coffee,
temperature of hot water,volume of hot water,dispense time of making
hot milk, dispense time of making hot foam
The parameters accomplished by the beverage setting will be the
default values for each beverage.
1. Espresso setting
2. Long coffee setting
3. Hot water setting
4. Cappuccino setting
5. Coffee latte setting
6. Hot milk setting
7. Hot foam setting
Setting beverage parameters and range
The parameters such as strength, volume, temperature and time can be set
forthe beverages below.
The strength and volume of espresso can be set
The strength and volume of long coffee can be set
The strength and volume of coffee part of cappuccino can be
set
The foam dispensing time in cappuccino can be set
The strength and volume of coffee part and the waiting time in latte
can be set
The temperature and the volume of hot water can be set
Hot milk making time can be set
Hot foam making time can be set
Please read the following table for the detail setting parameters and
adjustment range
Strength
Drinks
espresso
long coffee
Mild:
Normal:
Strong:
cappuccino
coffee Latte
Mild:
Normal:
Strong:
hot water
hot milk
hot foam
10
Volume range
Default
Volume: 15 -120ML
50ML
Volume: 15 - 240ML
100ML
Volume: 15 - 240ML
Milk time: 0 - 120SEC
Foam time: 3 - 120SEC
Wait time: 0 - 30SEC
60ML
Foam time: 20SEC
60ML
Milk time: 15SEC
Foam time: 20SEC
Wait : 20SEC
Volume: 25 -450ML
100ML
Milk time: 3 -120SEC
15 SEC
Foam time: 3 -120SEC
15 SEC
Temperature Setting
The coffee temperature can be adjusted to your liking with the “ Temperature setting”
function and you can choose:
1 .Low
2 .Normal
3 .High
The default temperature is Normal, and it’s only adjustable for coffee not milk.
Program setting
Eco settings
● If the machine is set to Eco-setting, the machine needs 30
seconds to warm up to make Cappuccino, Coffee Latte, Hot
milk and foam. . The normal setting has more energy
consumption than the Eco-saving mode.
● The factory default setting of the machine is normal mode.After
entering the program setting, please turn the rotarybutton to
“ECO SETTING” option, then press the rotary button,setting is
finished.
Automatic power-down
● The machine’s default switch off time is 4 hours, which
means the machine will automatically switch off 4 hours
after the last use .
● The setting range of automatic switch-off is from 15 minutes to
24 hours.
● After entering the program setting, please turn the rotary
button to the “Auto-off” option. Then press the rotary button,
the setting is completed.
Factory Reset
● This function will reset all the menu setting and default
beverage parameters to the factory settings (except the
language options). However the information options will
not be reset.
● After entering the program setting, please turn the rotarybutton to
the “FACTORY RESET” option then press the rotary button to
confirm, the setting is completed.
Information Statics
11
●In this program you can view the statistical information on
the number of drinks, total drinks numbers, etc.
1. Number of rinses
2. Number of total cycles
3. Number of espresso
4. Number of long coffee
5. Number of hot water
6. Number of cappuccino
7. Number of coffee latte
8. Number of hot milk
9. Number of hot foam
10. Number of descales
11. Number of ground coffee
12. Number of brew unit cleans
13. Number of milk unit rinses
● When first viewed there will already be a number of
produced beverages because each coffee machine has
been tested before leaving the factory.
Language
● You can set your preferred language on the coffee machine.
● After entering the program setting, turn the rotary button to the "CHOOSE
LANGUAGE" option, then press the rotary button, rotate the rotary to
choose the language, and press the rotary button, the language setting
is completed.
EXIT
● After entering the program setting, please turn the rotary button to the
“EXIT” option. Then press the rotary button. The machine will return to
“READY” .
Cleaning and maintenance
This chapter will instruct you on how to clean and maintain
the coffee machine.
Paying attention to daily maintenance of the coffee
machine,will not only ensure the taste of each cup of
coffee, but also extend the life of the coffee machine.
Cleaning the coffee machine before operation
This chapter will instruct you on how to clean and maintain the
coffee machine.
Cleaning function must be processed in “READY” status.
READY
When the coffee machine is in “READY”
status and the cleaning indicator light is not
on, press the cleaning button to start
cleaning the brewing unit and coffee
spout.
READY
The process of cleaning coffee machine
cannot be interrupted, and it will
automatically return to “READY” status after
cleaning.
CLEANING
12
Cleaning brewing unit
After a long-term use, there will be some coffee ground left in the
brewing unit. Remove the grounds by deeply cleaning the
brewing unit.
The process of cleaning the brewing unit takes about 20minutes.
After entering the program settings, turn the
rotary button to the "MAINTENANCE" option,
and press the rotary button.
MAINTENANCE
CLEAN BREW UNIT
When the screen shows the picture on the
left, it indicates cleaning the brewing unit
program has been selected. Press the
cleaningbutton to start cleaning the
brewing unit.
The brew unit is cleaning.
CLEANING
Cleaning and maintenance
OPEN COVER ADD
CLEANING TABLET
CLOSE COVER
PRESS RINSE
Open the pre-ground coffee chute cover,
add the cleaning tablet.
Close the pre-ground coffee chute
cover,press the cleaning button to
start the cleaning process.
The screen will display as the left picture,
CLEAN
Brew unit is now cleaning.
CLEANING
After cleaning has finished, the machine
re-enters into “READY” status.
READY
13
Please empty the drip tray after the cleaning program is completed.
First 5 cups must be discarded after cleaning.
RINSE MILK UNIT
● After long-term use, some milk waste would be left in the Milk unit and
needs to be cleaned.
Enter the program setting, Turn the
rotary button to the“MAINTENANCE”
page and pressed the rotary button.
MAINTENANCE
When showing left picture in the display, it is
now in milk unit cleaning mode, press the
cleaning button to start.
RINSE MILK UNIT
Remove the milk pipe from the milk
container and insert it into the hole in the
drip tray grid according to the display.
Press the rinse button to rinse milk unit.
REMOVE MILK PIPE
PRESS RINSE
Cleaning and maintenance
Milk unit is cleaning.
After cleaning is finished, the machine
enters into “READY” status.
RINSE MILK UNIT
Please empty the drip tray after the cleaning process is completed.
First 5 cups must be discarded after cleaning.
Descaling the coffee machine
The daily usage will cause calcium deposits in the coffee
machine. The depositing rate varies with the local water
hardness.
Decalcifier contains acidic substances that
could hurt your eyes and skin, so you must strictly
comply with the security warnings noted by the
manufacturer on the packaging.
Dissolve the decalcifier in clean water, and then put the
mixed liquid into the water tank. Fully dissolved the
Decalcifier can descale the coffee machine more
thoroughly.
The whole descaling process takes about 30 minutes.
Do not cancel the descaling process or you will damage
the coffee machine. So once you start the descaling
process,please do not terminate it midway or turn off
power to themachine.
14
NEED DESCALE
PRESS RINSE
After a certain time of use, if it reaches a
high degree of scaling, “NEEDS DESCALE"
and"PRESS RINSE " will automatically
display on
the screen alternately. Now, press the
cleaning button to enter the descaling
program.
Turn the rotary button to the maintenance
setting option, press the rotary button to
enter.
MAINTENANCE
Turn the rotary button to descaling option,
press rotary button to enter
DESCALE
30 MINS
PRESS RINSE
After entering the descaling program, press
the cleaning button to start the descaling
program; it will take about 30 minutes.
Cleaning and maintenance
Take a bag of decalcifier and sufficiently
dissolve it in clean water, then put this
mixed liquid to the water tank, and reinstall
the water tank to the coffee machine.
SOLVENT IN TANK
After adding decalcifier, press the
cleaningbutton to start descaling and
cleaning.
PRESS RINSE
DECALCIFYING
To start descaling and cleaning for the first
time, put a container, of which the
capacity is more than 1L, under the coffee
spout.
Empty tray.
EMPTY TRAY
Install tray.
INSTALL TRAY
15
FILL WATER TANK
PRESS RINSE
After descaling and cleaning for the first
time, take the water tank out, empty the
rest of the water and clean it. Add
potable water again, and reinstall it to the
coffee machine
Press the cleaning button to enter
descaling and cleaning for the second
time. This is to clean the residual
decalcifying water in pipes at this time . Put
a container, of which thecapacity is more
than 1L, under the coffeespout.
Decalcifying.
DECALCIFYING
When the screen shows “READY”, it indicates
the descaling is completed; Now, you can
continue to brew beverages.
READY
Please empty the drip tray after the cleaning program is completed.
First 5 cups must be discarded after cleaning.
Cleaning and maintenance
Cleaning coffee grounds container and drip tray
● Do not use chemical solvents and corrosive cleaner or alcohol
to clean the coffee grounds container and drip tray.
● The drip tray and coffee grounds container cannot be cleaned
in dishwasher.
● Do not use metal objects to clean dirt or coffee residue to
avoid scraping the drip tray and coffee grounds container.
1
●When prompted to empty the coffee grounds, coffee grounds
must be cleaned up, or it will cause the machine to be
damaged.
.
When it accumulates to 35 cups, it will
automatically indicate “EMPTY GROUNDS”.
2
EMPTY GROUNDS
INSTALL TRAY
When it shows “INSTALL TRAY “, please
remove coffee grounds from the drip tray
and coffee grounds container. This will take
more than 3 seconds.
Reinstall the water drip tray in the machine,
it should returns to “READY” status. You can
continue using the machine.
3
16
READY
EMPTY TRAY
If the drip tray is full, the machine will
automatically indicate"EMPTY TRAY". Take
out the water drip tray and dispose of
waste water.
4
INSTALL TRAY
READY
After clearing the waste water, reinstall the
drip tray to the coffee machine, it should
returns to“READY” status. You can continue
using the machine.
● Each time you are cleaning coffee grounds and waste water
from the drip tray, please empty the drip tray and coffee
groundscontainer.
● Each time after cleaning coffee grounds and waste water from the drip
tray, please rinse the tray with clean water, and wipe dry the 2 steel plates
at the end of drip tray, then reinstall the drip tray to the coffee machine.
Cleaning and maintenance
Cleaning water tank
● It is suggested that, each time adding water, clean the tank
thoroughly with running water first.
● Cleaning the water tank regularly
it would be better to use a wet rag and some mild
cleaning fluid.
● Because the water tank is made from food-grade materials and
environmental materials, it might crack if handled
aggressively. Please gently pick it up and put it down, and
never let it fall down. if the water tank is damaged, please
contact the customer service center.
Cleaning bean container
● Please do not use water to wash the beans hopper it, would
cause the grinder to be damaged.
● Please use a dry rag or a paper towel to clean the grease
residue in the bean hopper .
● Because the bean container cover is made from food-grade
and environmental materials, it might crack if handle aggre
. ssively.
Please gently pick it up and put it down, and never let it fall
down. If the bean container lid is damaged , please contact
the customer service center.
Disassembling and cleaning the milk frother
In order to guarantee the fine and smooth milk foam, please
clean the milk frother every day.
17
1. Carefully take off the milk frother.
2. Disassemble each part of the milk frother thoroughly.
3. Wash the parts with running water.
4. Reassemble the milk frother, and install it to the coffee
machine.
1
2
Installing milk pipe
● Install the milk pipe to the milk frother inlet.
Cleaning milk pipe
In order to keep milk pipe clean, please clean it every day.
1. Take off milk pipe carefully.
2. Clean milk pipe in running water.
3
4
Cleaning coffee machine
● Before cleaning the interior of the coffee machine, power it
off, the disconnect power cord from the outlet ,Never
immerse the coffee machine inwater. There will be a risk of
electric shock.
● Regularly check the coffee machine whether there is excessive
coffee grounds residue inside the machine. You can use a
brush to remove the coffee ground.
● Use a dry and soft rag to wipe the touch panel of the machine.
As the touch panel is made of glass, please do not hit it to
avoid the risk of electric shock once the glass broken.
● Use a dry and soft rag to wipe the surface of the machine,
and never use hard objects to clean coffee residue on the
surface, otherwise it would cause the surface to be
damaged.
Problem Causes and Solutions
● This chapter will instruct you on some errors that you may
encounterand the solutions.
● If there are some failures cannot be resolved by the following
methods, please contact with the authorized service center.
Problem
The coffee temperature is too low.
Coffee only comes out from the
coffee spout drop by drop.
Cause
Solutions
The coffee cup was not pre-heated.
Wash the coffee cup with hot water
before making coffee.
Several minutes have passed since the
last time of coffee making , so the
brewing unit and the internal pipes are
already cold.
Make some more cups of coffee.
Overly fine pre -ground coffee or coffee
bean has been ground too fine.
Adjust the grinding level to coarse
or use the suitable pre-ground coffee .
Brewing unit filter was blocked.
Run the brewing unit rinse programme
Insufficient coffee oil.
Chose the wrong coffee bean type.
The grinder is making unusual noises.
There are foreign objects in the grinder.
Make coffee again, if it still fails, please
contact the authorized service center
The milk frother cannot make any milk
foam.
The milk frother is blocked.
Cleaning the milk frother ( refer to P17).
Milk sprays from the milk frother.
The milk frother was not assembled
correctly.
Reassemble the milk frother.
Screen always indicates "EMPTY TRAY".
The sheet metal at the end of the drip
tray is dirty or wet.
Screen always indicates "INSTALL TRAY".
Coffee grounds in the bottom of the
machine are not cleaned.
Clean the coffee grounds in the bottom.
Screen always indicates “FILL WATER
TANK”, but the water tank is full.
The water tank inductor is trapped.
Clean the water tank ( refer to P17).
Screen always indicates “FILL BEANS”,
but the bean container is full.
The bean container is too oily and
sticky for coffee beans.
1. Stir coffee beans in bean container.
2. Observe if the coffee beans are over
roasted or charcoal roasted.
3. Clean the beans container ( refer to
P17).
“Errors 1 to 7”is displayed.
If the coffee machine fails, it cannot
continue to be used
1. Restart coffee machine.
2. If “errors” still exist, switch off the main
power, and contact the authorized
service center
Use suitable coffee beans.
Wipe the sheet metal to dry ( refer to P16).
18
Display information
● This chapter will instruct you on the error information
that is displayed on the screen and the solutions.
Causes
EMPTY TRAY
EMPTY GROUNDS
FILL WATER TANK
FILL BEANS
FILL POWDER
19
INSTALL TRAY
UNIT EMPTY
Solutions
If the water drip tray is full,
making beverage will be out of
service.
Take the drip tray out, empty the
waste water in the drip tray and
reinstall it to the machine.
If the coffee grounds container is
full, making beverage will be out
of service.
Take the coffee grounds container
out, empty the coffee grounds
container and reinstall it.
If water in the water tank is
empty, making beverage will
be out of service.
Fill the water tank with water.
If coffee beans in the bean
hopper are used up, making
coffee will be out ofservice.
Add beans into bean container,
and press the rotary button to
release.
There is not enough pre ground coffee in the
pre-ground coffee chute.
Next time when making coffee
with pre-ground coffee , please
use proper amount.
The drip tray is not installed
correctly; any function is out of
service.
Install the drip tray correctly.
The water in the pipe inside the
machine is not enough; any
function is out of service.
Press the rotary button to release,
to run the water replenishing system.
Temperature of the machine is too
high, the machine cannot be used.
Power off the main power, and
wait 1 hour later.
Temperature of the machine is too
low, the machine cannot be used.
Increase environmental temperature
to above 10℃.
The coffee machine fails
error1.may not be able to be
used.
1. Power off, then power back
on ;2. If still unresolved, please
unplug from outlet.Contact with
the authorized service center.
1. Using dark roasted coffee beans
or over fine pre-ground coffee
2. The filter of the brewer is
clogged.
1.Adjust grinder wheel to a coarse
setting2. Start brewer cleaning
procedure(refer to P12).
Dispenser valve is blocked.
Restart coffee machine.
TEMPERATURE HIGH
TEMPERATURE LOW
ERROR 1
PRESSURE HIGH
VALVE RESET
RESTART MACHINE
Transport and recycle
Transport
Please save the packaging of the coffee machine for future
transportation.
Make sure to empty water inside the machine before transportation,
otherwise, it will damage the machine.
After emptying the waterway, please wipe the machine both
inside and outside to dry.
Once the empty waterway program was executed, the system
will rerun to the program of “first-time use”, when the coffee
machine is used again.( refer to P6, First-time use)
While emptying the waterway, there will be high-temperature
steam sprays from coffee spout. Please pay special attention to
avoid being scalded.
The machine is on the status of “READY”.
READY
Take out the water tank, and the machine
indicates “FILL WATER TANK”.
FILL WATER TANK
EMPTY UNIT
Press and hold the cleaning button until
the screen shows "EMPTY UNIT", themachine
begins to clean up the waterway
automatically, and steam will spray fromthe
coffee spout, please keep your distance to
avoid scalding.
After emptying the waterway, the machine
will automatically power off. Take the drip
tray out after the power is switched off, and
clear the water in the drip tray.
Recycle
When recycling the machine, some inner parts can be
recycled to use again. Please pay attention to recycle them
for environmental protection.
Technical Data
Voltage/Frequency
120V~ 50/60 Hz
Power
1450 W
Pump pressure
19 bar
Capacity of water tank
2 L or connect to water barrel
Capacity of bean hopper
750 g
Capacity of coffee ground waste bin
35 cakes
Capacity of the brewing unit
7 - 14 g
Adjusting the height of coffee spout
80 - 140 mm
Length of power cord
1.5 m
Net weight
16 kg
Dimensions (Length×Width×Height)
533mm×383mm×662mm
20