GN016-SBH | Desktop or Vehicle Dash | Console Mount
Patent Pending
Swivel Mount
Pedestal
Removable
Desktop
Gel Disc
Optional
Dash / Console
Mounting
Screws
Foam Adhesive
Mounting Disc
Package Contents:
(1) GN016-SBH - Swivel mount pedestal
(1) Semi-permanent foam adhesive mounting disc (optional)
(1) Removable desktop gel disc (optional)
(1) Set of 3 mounting screws (optional)
(1) Alcohol cleaning pad
!
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road.
Desktop Mount Installation
Step 1.
Clean the desk or other smooth surface area and let dry.
Step 2.
Remove the backing on one side of the gel disc and place the
sticky side down on the cleaned surface. Press the top of the
disc down firmly to allow the gel to stick to the surface.
Step 2.
Remove the backing on the top side of the gel disc and firmly
press the pedestal down on the adhesive disc.
Step 3.
To remove the desktop gel disc, simply peel and lift up. Clean
the disc with soap and water to revive the gel’s stickyness.
Vehicle Dash or Console Mount Installation
Step 1.
Find a safe location on the vehicle dash or console. Clean the
dash or console surface area thoroughly with the included
alcohol pad. Allow the area dry before applying the disc.
Step 2.
Remove the paper backing on one side of the disc and place
the sticky side down on the cleaned surface. Press the top
of the disc down firmly to allow the adhesive to stick to the
surface. Allow 24 hours for the adhesive to cure to the surface
before attaching the mount.
Step 3.
Remove the paper on the top side and firmly press the mount
down on the adhesive disc.
Optional Screw Mounting
!
Safety Precautions
Drilling into the dash or console is a permanent installation
to the vehicle. Use caution and consult a mobile install
professional to avoid drilling into the gas tank, electrical
system or other highly sensitive vehicle components.
Arkon Resources, Inc. is not responsible for any damages
caused to your car or yourself due to the install of the
pedestal mount.
Continued on other side...
!
Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
www.arkon.com
Consumer Hotline:
Arcadia, CA 91006 USA
USA (800) 841-0884
Designed in USA | Made in China and Taiwan
INT’L (626) 254-9005
© Copyright 2009 Arkon Resources, Inc.
Monday - Friday 9 am - 5 pm, PST
GN016-SBH | Desktop or Vehicle Dash | Console Mount - Continued
Continued from previous side...
Step 1.
Using a screwdriver, tighten the 3 screws (A) through the
pedestal base holes (B) into the mounting surface.
A
B
Dual T Device Attachment
Step 1.
While holding the pedestal, firmly slide the dual T slots on the
back of your cradle or device (not included, sold separately)
on to the dual T tabs of the pedestal head. Adjust the angle
of the pedestal head and tighten the adjustment ring (C).
C
!
Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
www.arkon.com
Consumer Hotline:
Arcadia, CA 91006 USA
USA (800) 841-0884
Designed in USA | Made in China and Taiwan
INT’L (626) 254-9005
© Copyright 2009 Arkon Resources, Inc.
Monday - Friday 9 am - 5 pm, PST