Fully Integrated Dishwasher MDI500

THE PERFECT BALANCE OF FUNCTION AND STYLE
LAUNDRY - DISHWASHING - COOKING - COOLING
Installation and Operating Instructions
Fully Integrated Dishwasher
MDI500 - Slimline - 45cm
Please read these instructions carefully before attempting to install or use this appliance.
We recommend that you keep these instructions in a safe place for future reference.
Welcome
Thank you for choosing this Montpellier Integrated Dishwasher.
Our Integrated Dishwasher has been designed to provide you with the best combination of style, reliability and
performance to give you years of trouble-free use.
You may be familiar with a similar product, but please take time to read these instructions carefully before installing or
using your Integrated Dishwasher to ensure you get the most from your purchase.
We recommend that you keep this manual in a safe place for future reference.
Your Integrated Dishwasher is covered by a comprehensive two year Parts &
Labour Guarantee. In the unlikely event that you experience a problem with your
Integrated Dishwasher, you can rest assured that you are fully protected against
the cost of repairs for the first 24 months . Please note that any claim must
be accompanied by the model reference number, serial number and proof of
purchase.
YEAR
GUARANTEE
PARTS & LABOUR
ACROSS ALL OUR MODELS
www.montpellier-appliances.com
To activate your guarantee, you will need your product serial number. This can be
found on the rear of the machine.
There are two ways to register your Guarantee:
Visit the Support page on our website and complete the online Product
• Online:
Registration form. www.montpellier-appliances.com
y Post: Simply detach and fill in the form provided, attach a stamp and send
•B
it in the post. Don’t forget to include your e-mail address so that we can send
confirmation through to you.
Note: W
e are unable to take registrations over the phone.
CONTENTS

Technical specifications ....................................................................................... 4
Safety information and Recommendations ..........................................................5




Recycling ............................................................................................................... 5
Safety information.................................................................................................5
Recommendations .................................................................................... 8
Items not suitable for dishwashing ..................................................................... 9
Installing the machine................................................................................................. 9






Positioning the machine........................................................................................ 9
Water connections ................................................................................................ 10
Water inlet hose .................................................................................................... 11
Water outlet hose ................................................................................................. 12
Electrical connection .................................................................................. 13
Prior to using the machine ......................................................................... 14
Preparing the machine for use ....................................................................... 14








The importance of water decalcification ..................................................... 14
Filling with salt ........................................................................................... 14
Testing strip ............................................................................................... 15
Adjusting salt consumption ........................................................................ 15
Detergent usage ........................................................................................ 17
Filling the detergent compartment .............................................................. 17
Combined detergent .................................................................................. 17
Filling with rinse aid and making the setting ............................................... 18
1
Loading your dishwasher .............................................................................. 19


Top basket ............................................................................................... 19
Alternative basket loads .................................................................................... 22
Programme descriptions ........................................................................................24

Programme items ...............................................................................................24
Getting familiar with your machine ...................................................................... 25
Switching on the machine and selecting a programme ..................................27





Switching on the machine .................................................................................27
Programme follow-up.........................................................................................27
Changing a programme.....................................................................................27
Changing a programme with resetting ............................................................28
Switching the machine off .................................................................................28
Maintenance and Cleaning .....................................................................................29



Filters ...................................................................................................................29
Spray arms..........................................................................................................30
Hose filter ............................................................................................................30
Failure codes and what to do in case of failure .................................................31
Practical and useful information ........................................................................... 33
2
3
8
9
10
11
provides better drying
performance for your dishes.
12 Drying with Fan: This system
7
6
4
5
3
2
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
for utensils in the upper basket.
better washing performance
Fixed Top Sprinkler: Provides
13
Control Panel
Detergent and rinse-aid dis
Salt dispenser
Upper basket track
latch Upper Cutlery
Basket
Upper basket with
racks Upper spray arm
Lower basket
Lower spray arm Filters
Rating plate
Technical specifications
Capacity
10 place settings
Width
450 mm
Height
Depth
Net Weight
Electricity input
Total Power
Heating Power
Pump Power
Drain Pump Power
Water supply pressure
Current
820 mm - 870 mm
550 mm
32 kg
220-240 V, 50 Hz
1900 W
1800 W
100 W
30 W
0.03 MPa (0,3 bar)-1 MPa (10 bar)
10 A
Conformity with the standards and Test data / EU Declaration of
Conformity
This product meets the requirements of all applicable EU directives
with the corresponding harmonised standards, which provide for CE
marking.
Important Note for User:For softcopy of this user manual, please
contact following address:
"dishwasher@standardtest.info”.In your e-mail, please provide the
model name and serial number (20 digits) which you can find on the
appliance door.
4
SAFETYINFORMATIONANDRECOMMENDATIONS Recycling
• Certain components and the packaging of your machine
have been produced from recyclable materials.
• Plastic parts are marked with international abbreviations:
(>PE< , >PS< , >POM<, >PP<, )
• Cardboard parts have been produced from recycled paper
and they should be disposed of into waste paper collection
containers for recycling.
• Such materials are not suitable for being disposed of into
garbage bins. They should be delivered to recycling centres
instead.
• Contact relevant centres in order to obtain information on
methods and points of disposal.
Safety Information
When you take delivery of your machine
• Check for any damage to your machine or to its packaging.
Never start a machine damaged in any way, make sure to
contact an authorised service.
• Unwrap the packaging materials as indicated and dispose
of them in accordance with the rules.
The points to pay attention during machine installation
• Choose a suitable, safe and level place to install your
machine.
• Carry out the installation and connection of your machine by
following the instructions.
• This machine should be installed and repaired by an
authorised service only.
• Only original spare parts should be used with the machine.
• Before installing, be sure that the machine is unplugged.
5
• Check whether the indoor electrical fuse system is
connected according to the regulations.
• All electrical connections must match the values
indicated on the rating plate.
• Pay special attention and be sure that the machine does
not stand on the electricity supply cable.
• Never use an extension cord or a multiple socket for
making a connection. The plug should be comfortably
accessible after the machine has been installed.
• After installing the machine to a suitable place, run it
unloaded for the first time.
In daily use
• This machine is for household use; do not use it for
any other purpose. Commercial usage of the dishwasher
will void the guarantee.
• Do not get up, sit or place a load on the open door of
the dishwasher, it may fall over.
• Never put into the detergent and rinse aid dispensers
of your machine anything other than those detergents
and rinse aids which are produced specifically for
dishwashers. Our company will not be responsible for
any damage that might occur in your machine otherwise.
• The water in the machine's washing section is no
drinking water do not drink it.
• Due to danger of explosion, do not put into the
machine’s washing section any chemical dissolving
agents such as solvents.
• Check whether plastic items are heat-resistant
before washing them in the machine.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or
6
mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.Cleaning and user maintenance
shall not be made by children without supervision.
• Do not put into your machine those items which are
not suitable for dishwashing. Also, do not fill any basket
above its capacity.Our company will not be responsible
for any scratch or rust to form on the inner frame of
your machine due to basket movements otherwise.
• Especially because hot water may flow out, the
machine door should not be opened under any
circumstances while the machine is in operation. In any
case, a safety devices ensures that the machine stops if
the door is opened.
• Do not leave your dishwasher’s door open. Failure to do
so may lead to accidents.
• Place knives and other sharp-ended objects in the
cutlery basket in blade-down position.
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
• This appliance is not intended for use by persons
(including -children) with reduced physical,sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• If EnergySave option is selected as "Yes", The door will
be opened at the end of the program. Do not force to
close the door to avoid harm auto door mechanism
during 1 minutes. The door must be open during 30
minutes to get effective drying.( in models with auto door
opening system ) Warning: Do not stand in front of the
door after the signal sounds belonging auto-open.
7
For your children’s safety
• After removing the machine’s packaging, make sure
that the packaging material is out of reach of children.
• Do not allow children to play with or start the machine.
• Keep your children away from detergents and rinse
aids.
• Keep children away from the machine while it is
open because there may still be residues of cleaning
substances inside the machine.
• Be sure that your old machine does not pose any
threat to your children. Children are known to have
gotten themselves locked in old machines. To forestall
such a situation, break your machine's door lock and
tear off the electrical cables. In case of malfunctioning
• Any malfunction in the machine should be repaired
definitely by qualified persons. Any repair work
performed by anyone other than the authorised
service personnel will cause your machine to be left
outside the scope of warranty.
• Prior to any repair work on the machine, be sure that
the machine is cut off from the mains.Switch off the fuse
or unplug the machine.Do not pull by the cable when
unplugging. Make sure to turn off the water tap.
Recommendations
• For energy and water saving, remove coarse
residues on your dishes before placing the dishes into
the machine. Start your machine after having fully
loaded it.
• Use the pre-wash programme only whenever
necessary.
• Place such hollow items as bowls, glasses and pots
into the machine in such a way that they will face down.
• You are recommended not to load into your machine
any dishes different or more than indicated.
8
Items not suitable for dishwashing:
• Cigarette ashes, candle leftovers, polish, paint, chemical
substances, iron-alloy materials;
• Forks, spoons and knives with wooden or bone, or ivory
or nacre-coated handles; glued items,items soiled with
abrasive, acidic or base chemicals.
• Plastic items that are not heat-resistant, copper or tincoated containers.
• Aluminium and silver objects (they may discolour,
become dull).
• Certain delicate glass types, porcelains with
ornamental printed patterns as they fade even after the
first wash; certain crystal items as they lose their
transparency over time, adhered cutlery that is not heatresistant, lead crystal glasses, cutting boards, items
manufactured with synthetic fibre;
• Absorbent items as sponges or kitchen rags are not
suitable for dishwashing.
Warning:Take care to buy dishwasher-proof sets in
your future purchases.
INSTALLING THE MACHINE
Positioning the machine
When determining the place to put your machine on,
take care to choose a place where you can easily load
and unload your dishes.
Do not put your machine in any location where there is
the probability for the room temperature to fall below 0°
C.
Before positioning, take the machine out of its packaging
by following the warnings located on the package.
9
Position the machine close to a water tap or drain.
You need to site your machine, taking into
consideration that its connections will not be altered
once they are made.
Do not grip the machine by its door or panel in order to
move it.
Take care to leave a certain clearance from all sides of
the machine so that you can comfortably move it back
and forth during cleaning.
Make sure that the water inlet and outlet hoses do not
get squeezed while positioning the machine. Also,
make sure that the machine does not stand on the
electrical cable.
Adjust the machine’s adjustable feet so that it can stand
level and balanced. Proper positioning of the machine
ensures problem-free opening and closing of its door.
If the door of you machine does not close properly,
check if the machine is stable on the floor it stands; if
not, adjust the adjustable feet and ensure its stable
position.
Water connection
Be sure that the indoor plumbing is suitable for
installing a dishwasher. Also, we recommend that you
fit a filter at the entrance of your place or apartment so as
to avoid any damage to your machine because of any
contamination (sand, clay, rust etc.) that might be
occasionally carried in through the mains water supply
or the indoor plumbing, and to forestall such
complaints as yellowing and formation of deposits after
washing.
10
Water inlet hose
Do not use the water inlet hose of
your old machine,if any. Use the new
water inlet hose supplied with your
machine instead. If you are going to
connect a new or long - unused water
inlet hose to your machine ,run water
through it for a while before making
the connection. Connect the water
inlet hose directly to the water inlet
tap. The pressure supplied by the
tap should be at a minimum of 0.03
Mpa and and at a maximum of 1 Mpa.If
the water pressure is above 1 Mpa,a
pressure-relief valve should be fitted
inbetween.
After the connections are made, the tap should be
turned on fully and checked for water tightness.For
the safety of your machine, make sure to always turn
off the water inlet tap after each wash programme is
finished.
NOTE: Aquastop water spout is
used in some models. In case
of using Aquastop, a dangerous
tension exists. Do not cut
Aquastop water spout. Do not
let it get folded or twisted.
11
Water outlet hose
The water drain hose can be
connected either directly to the
water drain hole or to the sink
outlet spigot. Using a special
bent pipe (if available), the
water can be drained directly
into the sink via hooking the
bent pipe over the edge of the
sink. This connection should be
at a minimum of 50 cm and at a
maximum of 110 cm from the
floor plane.
Warning: When a drain hose longer than 4 m is used,
the dishes might remain dirty. In that case, our
company will not accept responsibility.
12
Electrical connection
The earthed plug of your machine should be
connected to an earthed outlet supplied by suitable
voltage and current. If there is no earthing
installation, have a competent electrician carry out
an earthing installation. In case of usage without
earthing installed, our company will not be
responsible for any loss of usage that might occur.
The indoor fuse current value should be 10-16 A.
Your machine is set according to 220-240 V. If
the mains voltage in your location is 110 V,
connect a transformer of 110/220 V and 3000 W
inbetween. The machine should not be plugged in
during positioning.
Always use the coated plug supplied with your
machine.
Running in low voltage will cause a decline in washing
quality.
The machine’s electrical cable should be
replaced by an authorised service or an authorised
electrician only. Failure to do so may lead to
accidents.
For safety purposes, always make sure to
disconnect the plug when a wash programme is
finished.
In order not to cause an electric shock, do not
unplug when your hands are wet.
When disconnecting your machine from the
mains supply, always pull from the plug. Never pull
the cord itself.
13
Testing strip
The washing effectiveness of your machine depends on the softness of the tap water. For this
reason, your machine is equipped with a system that reduces the hardness in mains water supply.
The washing effectiveness will increase when the system is correctly set. To find out the water
hardness level of water in your area, contact your local water board or determine water hardness level
by using the test strip(if available).
Open the
testing
strip.
Run
water
through
your tap
for 1
min.
Keep the
testing
strip in
water for 1
sec.
Shake the
testing strip
after taking it
out of water.
Wait for
1 min.
Make your machine’s water hardness
setting according to the result
obtained through the testing strip.
Adjusting salt consumption
Table of Water Hardness Level Settings
Water
hardness
level
German
hardness
dH
French
hardness
dF
British
hardness
dE
Hardness Level Indicator
1
0-5
0-9
0-6
L1 is seen on display.
2
6-11
10-20
7-14
L2 is seen on display.
3
12-17
21-30
15-21
L3 is seen on display.
4
18-22
31-40
22-28
L4 is seen on display.
5
23-34
41-60
29-42
L5 is seen on display.
6
35-50
61-90
43-63
L6 is seen on display.
If the hardness of the water you use is above 90 dF (French hardness) or if you are using well
water; you are recommended to use filter and water refinement devices.
NOTE: Hardness level is adjusted to level 3 as a factory setting.
Adjust the water softener according to how hard your tap water is.
14
15
2
1
3
After resetting your machine, press the program selection button and keep it pressed
down.3
Meanwhile, energise the machine by pressing the Power On/Off button. 1
Keep the program selection button pressed until “SL” disappears from the
display.3
Release the program selection button after “SL” disappears from the display. 3
Your machine displays the latest entered water hardness setting.
Water hardness can be adjusted by the programme selection button .3
according to Table of Water Hardness Level Settings.
After adjusting the water hardness level , press on/off button to save settings in
memory.1
16
Detergent usage
Use a detergent specifically designed for use in domestic dishwashers.
You can find powder,gel,and tablet detergents in the market that have been designed for
household dishwashers.
Detergent should be put into the compartment prior to starting the machine. Keep your
detergents in cool, dry places out of reach of your children.
Do not fill detergent into the detergent compartment more than required; otherwise it may
cause scratches on your glasses as well as lead to a poorly dissolved detergent.
Should you need more information concerning the detergent you will use, contact detergent
manufacturers directly.
Filling the detergent compartment
Push the latch to open the detergent container as shown in the
image. 1 Detergent pod has level lines inside. It is possible to
measure the right detergent amount using these lines.
Detergent pod can take totally 40 cm3 detergent.
Open the dishwasher detergent and pour into the larger
compartment b 25 cm3 if your dishes are heavily soiled or 15
cm3 if they are less
soiled.2 If your dishes
have been kept dirty for
a very long time, if there
are dried food wastes
on them, and if you have overly loaded the dishwasher,
pour a 5 cm3 detergent into the pre-wash compartment
and start your machine.
You may have to add more detergent into your machine,
depending on the degree of soil and on the water
hardness level in your area.
Combined detergent
Detergent manufacturers also produce combined detergents called “2 in 1”, “3 in 1” or “5 in 1”
etc.
“2 in 1” detergents contain detergent + salt or rinse aid. When using “2 in 1” detergents make
sure to check the specifications of the tablet.
Other tablet detergents contain detergent + rinse aid + salt + varlous extra functions.
Generally, combined detergents produce sufficient results under certain usage conditions
only. Such detergents contain rinse aid and/or salt in preset amounts
Points to consider when using this type of products:

Always make sure to check the specifications of the product you will use or whether or not
it is a combined product.

Check if the detergent used is appropriate for the hardness of mains water that machine is
appertaining to.

Observe the instructions on packagings when using such products.

If such detergents are in the form of tablets, never put them into the interior section or the
cutlery basket of the dishwasher. Always put the tablets into the detergent compartment
in the detergent dispenser.
17



They produce good results for certain types of usage only. If you are using this type of
detergents, you need to contact the manufacturers and find out about the suitable
conditions of use.
When the conditions of use of such products and the machine settings are appropriate,
they ensure savings in salt and/or rinse aid consumption.
Contact the detergent manufacturers if you are not obtaining good wash results (if your
dishes stay calcareous and wet) after having used 2 in 1 or 3 in 1 detergents. The scope of
warranty for your machine does not cover any complaints caused by the use of these types
of detergents.
Recommended usage: If you are using a combined detergent, then add rinse agent into your
machine ,switch the rinse agent settings into its lowest (1) position and active the tablet
detergent button in order to obtain better results.If the water hardness level is above level
4,then it is necessary to fill in the salt container with salt.İt is not recommended to use combined
detergents in fast programs.
Warning: Should any problem, which you have not encountered before, arise with the use of this
type of detergents, contact the detergent manufacturers directly.
When you give up using combined detergents

Fill the salt and rinse aid compartments.

Adjust the water hardness setting to the highest position and run an emptywash.

Adjust the water hardness level.

Make the suitable rinse aid setting.
Filling with rinse aid and making the setting
Rinse aid is used to prevent the stay of white water drops, lime stains, white film strip-shaped
stains that may form on the dishes, as well as to increase the drying performance. Contrary to
the popular beliefs, it is used not only for obtaining shinier dishes but also for obtaining
sufficiently dried dishes. For this reason, care should be taken that there is adequate amount of
rinse aid in the rinse aid compartment and only polishing material produced for use at
dishwashers should be used.
If the rinse aid lamp on the control panel becomes on fill the rinse
aid compartment with rinse.
To put rinse aid, remove the rinse aid compartment cap by turning
it.1 Fill the rinse aid compartment with rinse aid until the rinse aid
level indicator becomes dark;2 refit the cap and close it by turning
it in a way that the nails will correspond to one another. By
checking the rinse aid level indicator on the detergent dispenser,
you can understand whether or not your machine needs rinse aid.
A dark indicator b means that there
is rinse aid in the compartment, while
a light indicator a shows that
you need to fill the compartment
with rinse aid.
The rinse aid level adjuster can be
set to a position between 1 and 6.
Factory setting for rinse aid is the
position 3. You need to increase
the degree of the adjuster if water
stains form on your dishes after a wash, whereas you need to
decrease the degree if a blue stain is left when wiped by hand.3
18
Warning: Use only those rinse aid materials which are allowed for use in the machine. As rinse
aid residues left as a result of overflowing will create extremely high amounts of foam and thus
reduce the washing performance, remove the excess amount of rinse aid by wiping it with a rag.
LOADING YOUR DISHWASHER
If you properly place your dishes into the machine, you will be using it in the best way in terms of
energy consumption, washing and drying performance.
There are two separate baskets for you to load your dishes into your machine. You can load into
the lower basket such round and deep items as pots with long handles, pot lids, plates, salad
plates, cutlery sets.
The upper basket has been designed for tea plates, dessert plates, salad bowls, cups and
glasses. When placing long-stem glasses and goblets, lean them against the basket edge, rack
or glass supporter wire and not against other items. Do not lean long glasses against one
another or they cannot remain steady and may receive damage.
It is more appropriate to locate the thin narrow parts into the middle sections of baskets.
You can place spoons among the other cutlery sets in order to prevent them from sticking to
one another. You are recommended to use the cutlery grid in order to obtain the best result.
To avoid any possible injuries, always place such long-handle and sharp-pointed dishes as
serving fork, bread knife etc. with their sharp points facing down or horizontally on the baskets.
Warning: Place your dishes into your machine in a way that they will not prevent the upper and
lower spray arms from spinning.
Dish rack
There are dish racks on the upper basket of your
machine. a b You can use these dish racks in open
or closed position. When they are in open position a
you can place your cups on them; and when in
closed position b you can place long glasses on the
basket. Also, you can use these racks by placing
long forks, knives and spoons on them laterally.
Foldable racks on the upper basket are designed in order to let you place big items easier such
as pots, pans, etc. If requested, each part can be folded separately, or all of them can be folded
and larger spaces can be obtained.You can use foldable racks by raising them upwards, or by
folding down.
19
.
Top basket height adjustment
Top basket of your machine is in upper position. When it is in this position, you can place big
items such as pans, etc. on lower basket. When you take top basket to lower position, you can
place and wash big sized plates on the top basket.
Use wheels in order to change the basket height. Open the basket retaining parts at the end of
top basket rails by turning them to the sides, and take the basket out. Change the position of
the wheels; reinstall the basket to the rail, and close basket retainer parts. In this way, you take
the top basket to lower position.
Lower Basket
Folding Racks
Folding racks consisting of two parts that are located on the lower basket of your machine are
designed in order to let you place big items easier such as pots, pans, etc. If requested, each
part can be folded separately, or all of them can be folded and larger spaces can be obtained.
You can use folding racks by raising them upwards, or by folding them down.
20
Upper Cutlery Basket
The upper cutlery basket is designed for you to place forks, spoons and knives, long dippers and small
items.
Because it can easily be taken out of the machine, it allows your dishes to be taken out of the machine
along with the basket after washing.
.
Warning: Knives and other sharp objects must be placed horizontally in the cutlery basket.
21
Alternative basket
loads Lower Basket
Top basket
22
Faulty loads
x
x
Important Note for Test Laboratories
x
For detailed information on performance tests, please contact following address:
"dishwasher@standardtest.info” . In your email, please provide the model name and
serial number (20 digits) which you can find on the appliance door.
23
24
9,6-16,1
10,0-20
111-96
0,81-1,02
0,93 -1,42
152-98
12,8
9,7-16
115
1,22
82-69
End
Dry
Hot rinse
Cold Rinse
70°C Wash
50°C Wash
high
A+B
Dishes with dense
dirt waiting for a
long time or
requiring hygienic
washing
70°C (P4)
Extra Hygiene
0,66-0,77
9,9
1,02
50
End
Hot rinse
Cold
Rinse
65°C Wash
medium
A+B
soups, sauces,
pasta, eggs, pilaf,
potato and oven
dishes, fried foods
65°C ( P5)
Super 50' 65°C
9,0
0,73
191
End
Dry
Hot rinse
Cold Rinse
50°C Wash
medium
A+B
coffee,milk,tea,cold
meats,vegetables
,not kept for long
50°C ( P6)
Eco
( reference )
9,9
0,55
30
End
Hot rinse
Cold Rinse
40°C Wash
small
B
coffee,milk,tea,cold
meats,vegetables
,not kept for long
40°C ( P7)
Quick
3,6
0,02
15
End
Prewash
Pre-wash tor ise
and loosen
residue awating
full load then
select a
programme
- ( P8 )
Prewash
The values declared above are the values obtained under laboratory conditions according to relevant standards. These values can change depending on
conditions of product’s use and environment (network tension, water pressure, water input temperature and environment temperature).
Warning : Short programs do not include a drying step.
Electricity
consumption
(kW hours)
Water consumption
(liters)
Programme duration
(min.)
Automatically adjust the washing
time with temperature and amount
of water by determining the soil level
of dishes
small
B
high
A+B
Level of soil
Detergent amount
B: 25 cm3 / 15 cm3
A: 5 cm3
high
A+B
60-70°C
50-60°C (P2)
30-50°C(P3)
(P1)
Automatically adjust the washing time with
temperature and amount of water by
determining the soil level of dishes
Auto
Delicate
Programme names
and temperatures
Type of food waste
Auto
Normal
Auto
Intensive
Programme No
Programme items
PROGRAMME DESCRIPTIONS
25
With the program selector button, you can select a suitable
program for your dishes.
3.) Program selection button
Program display indicates the times of the programs and the
remaining time during the program flow. You can also follow-up
the selected programs by this display.
2.) Program Display
When the Power On/Off button is pressed, end of program
indicator starts lighting.
1.) Power On/Off Button
1
GETTING FAMILIAR WITH YOUR MACHINE
4.) Delay Timer Button
3 4 5
6
7
You can delay the start time of a selected program for 1-2 ….19
hours by pressing the delay timer button of your machine. When
you press the delay timer button, delay “1h” appears on the
program display. If you continue pressing the delay timer button,
1-2… 19 will be displayed respectively. You can activate the
delayed start by selecting the delay time and the desired washing
program with the program selection button. It is also possible to
select the program first and the delayed start afterwards. If you
want to change or cancel the delayed start time, you can adjust it
with the delay timer button; it will be activated according to the
last value entered.
2
26
If you have dishes only in the lower basket, press the
key ½ and select the position in which the lower lamp is
illuminated. Thus, washing up shall be done only on the
lower basket of your machine. In using this feature,
make sure that there are no dishes in the upper
basket.
If you have dishes only in the upper basket, pres the
key ½ and select the position in which the upper lamp
is illuminated. Thus, washing up shall be done only on
the upper basket of your machine. No dishes
should certainly be available in the lower basket
while using this feature.
If you have little amount of dishes in your machine and
if you have to wash them, you can also activate the
semi-filling
function
in
some
of
the
programs additionally. If you have dishes in both
baskets, press the key ½ and select the position in
which both lamps are highlighted.
Using the function ½ , three sorts of washing up can be done
those being lower basket, upper basket and both baskets.
6.) ½ Half Load Button
Press tablet detergent button when you use combined
detergents that include salt and rinse aid.
5.) Tablet Detergent Button ( 3 in 1 button )
End of program indicator on the control panel turns on when the
selected washing program is completed .Your machine also gives
a buzzer sound for “5 times” when the program is completed.
End of Program Indicator
In order to check that there is sufficient rinse aid in your machine
check rinse aid lack warning light on the display.When rinse aid
warning light starts coming on , fill in rinse aid chamber.
Rinse aid Lack Warning indicator
In order to see whether softening salt in your machine is sufficient
or not, check salt lack warning light on the display.When salt light
warning light starts coming on, you need to fill in the salt chamber.
7.) Salt Lack Warning indicator
Note: When you select an incompatible program with the half
load button, a buzzer sound is heard which indicates that the
selected option is not compatible.
Note : If you have used an extra feature on the latest washing
program, this feature will remain active also on the next washing
program. If you do not want to use this feature on the newly
selected washing program, press the selected feature
button again, and check that the lamp on the button goes off.
SWITCHING ON THE MACHINE AND SELECTING A PROGRAMME
Switching on the machine
1
Machine is energized when the On/Off button is
2
pressed , two dashes appear in the progra m display
and the end of program indicator turns on.
When you select a program with the
program selection button,the program
you select ( P1,P2,etc )appears on the
program display and the end of program
indicator turns off.
3
1. Press the Power On/Off key.
2. Select the program suiting your dishes via the Program Selection
button.
3. If you prefer or wish to prefer , you can choose additional function.
4. Close door.The program starts automatically.
Note:If you decide not to start to machine after selecting the program , just press the on/off
button.Your machine will become ready for the new program selection when you press on/
off button again.You can select the new program by pressing the program selection button.
Program follow-up
Do not open the door before
the program ends.
End of program indicator on the control panel
turns on when the selected washing program is
completed .Your machine also gives a buzzer
sound for “5 times” when the program is
completed.
Changing a programme
If you would like to change programs while a washing program is continuing.
Open the door and select a new
program by pressing the
program selection button.
After closing the door ,
the new program started
will
resume the course of the
old program.
Note:When the door of the machine is opened in order to stop the washing program
before it is completed first open the door slightly in order to avoid water spillage.
27
Changing a programme with resetting
If you would like to cancel a program while a washing program is resumed
Open the door of your machine.
The last selected program will
appear on the screen.
Keep the program selection button pressed
for 3 seconds. End of program indicator
flashes and “1” is indicated on the program
display.
Discharge process starts after closing
the door of the machine.The machine
discharges the water in it for about 30
seconds.When the program is
cancelled,your machine gives a buzzer
sound for “5 times “ and the “end of
program indicator” turns on.
Note:When the door of the machine is opened in order to stop the washing program
before it is completed first open the door slightly in order to avoid water spillage.
Switching the machine off
When end of program indicator
turns on , switch your machine off
by using the Power On/Off button.
Pull the plug out of the outlet.
Turn off the water tap.
Note: After the buzzer sound which indicates the end of the program when the washing program
comes to an end (end indicator light is on), you can leave the door of your machine ajar in order to
hasten the drying.
Note: If the machine door opens during washing or the power is cut off, the machine will go on to the
program in case the door is shut or the power is back.
Note: If energy is cut or machine door is opened during drying process, program is terminated. Your machine
becomes ready for new program selection.
28
MAINTENANCE AND CLEANING
Cleaning the machine in regular intervals prolongs the machine’s service life.
Oil and lime may accumulate in the machine’s washing section. In case of such accumulation; -Fill the
detergent compartment without loading any dishes into the machine, select a programme that runs at
high temperature, and start the machine. In case of insufficiency, use special cleansing material
available in the market. (Cleansing material produced special to machines by detergent producers.)
Cleaning the seals in the machine door,
-To clean any accumulated residues in the door seals, wipe the seals regularly by using a dampened
cloth.
Cleaning the machine,
Clean the filters and spray arms at least once a month.
Unplug your machine and turn off its tap before starting the cleaning.
Do not use hard materials when cleaning your machine. Wipe with a fine cleaning material and a
dampened cloth.
Filters
Check if any food wastes have remained on the coarse and fine filters.
If any food wastes are left, remove the filters and clean them
thoroughly under the water tap.
a. Micro Filter
b. Coarse Filter
c. Metal/Plastic Filter
To remove and clean the filter
combination, turn it counter clockwise
and take it out by lifting upwards.1
Pull and remove the metal/plastic filter. 3
Then pull the coarse filter out of the micro
filter.2 Rinse it with lots of water under
the tap. Refit the metal/plastic filter. Insert
the coarse filter into the micro filter in a
way that the marks will correspond to one
another. Attach micro filter into the
metal/plastic filter and turn to the
direction of arrow and it is locked when
the arrow on micro filter can be seen
from across. 4



Never use your dishwasher without any filter.
Incorrect fitting of the filter will reduce the washing effectiveness.
Clean filters are very important in terms of the proper running of the
machine.
29
Spray arms
Check whether or not the holes for the upper
and lower spray arms are clogged. If there is any
clogging, remove the spray arms and clean them
under water.
You can remove the lower spray arm by pulling it
upwards, while the upper spray arm nut can be
removed by turning the nut to the left.
Be sure that the nut is perfectly tightened when
refitting the upper spray arm.
Hose filter
Water is prevented by the inlet hose filter so as to avoid any damage to your machine because of any
contamination (sand, clay, rust etc.) that might be occasionally carried in through the mains water
supply or the indoor plumbing, and to forestall such complaints as yellowing and formation of
deposits after washing. Check the filter and the hose from time to time and clean them if necessary.
To clean the filter, first turn off your tap and then remove the hose. After removing the filter from the
hose, clean it under the tap. Insert the cleaned filter back into its place inside the hose. Refit the hose.
30
If the programme won’t start

Check if the plug is connected.

Check your indoor fuses.

Be sure that the water inlet tap is turned on.

Be sure that you have closed the machine door.

Be sure that you switched off the machine by pressing the Power On / Off button.

Be sure that the water inlet filter and the machine filters are notclogged.
If detergent residues are left in the detergent compartment Detergent
has been added when the detergent compartment was wet.
If water is left inside the machine at the end of the programme

The water drain hose is clogged or twisted.

The filters are clogged.

The programme is not finished yet.
If the machine stops during a wash operation

Power failure.

Water inlet failure.

Program can be on standby mode.
If shaking and hitting noises are heard during a wash operation

Dishes placed incorrectly.

Spray arm hitting the dishes.
If there are partial food wastes left on the dishes

Dishes placed incorrectly into the machine, sprayed water did not reach related places.

Basket overly loaded.

Dishes leaning against one another.

Very small amount of detergent added.

An unsuitable, rather weak wash programme selected.

Spray arm clogged with food wastes.

Filters clogged.

Filters incorrectly fitted.

Water drain pump clogged.
If there are whitish stains on the dishes

A very small amount of detergent is being used.

Rinse aid dosage setting at a very low level.

No special salt is being used despite the high degree of water hardness.

Water softener system setting is at a very low level.

Salt compartment cap not closed well.

A detergent without phospate used; try one that contains phosphate.
If the dishes won't dry up

A programme without a dry operation
selected.

Rinse aid dosage set too low

Dishes unloaded too fast.
32
If there are rust stains on the dishes

Stainless-steel quality of the dishes washed is insufficient.

High rate of salt in the wash water.

Salt compartment cap not closed well.

Too much salt spilt into the sides and into the machine while filling it with salt.

Unhealthy mains grounding.
Door is not opened / closed properly ;

Not proper weight wooden part inserted on the door. ( Follow the weight given in the
Assembly manuel )

The tensile of the door spring not adjusted properly. Adjust it according to the Assembly
manuel.
Call an authorised service if the problem still persists after the controls or in case of any
malfunction not described above.
PRACTICAL AND USEFUL INFORMATION
1. Whenever you will not be operating your machine

Unplug the machine and then turn the water off.

Leave the door slightly ajar in order to prevent the formation of unpleasant smells.

Keep the machine interior clean.
2. Eliminating water droplets

Wash the dishes with the intensive programme.

Take all of the metal containers in the machine out.

Do not add detergent.
3. If you properly place your dishes into the machine, you will be using it in the best way in terms of
energy consumption, washing and drying performance.
4. Clean all rough waste before you place dirty dishes to themachine.
5. Operate the machine after it is completely full.
6. Use pre-washing program only when necessary.
7. Observe program information and average consumption values table when selecting a program.
8. Since the machine will reach high temperatures, it should not be mounted near refrigerator.
9. If the appliance is located in a place where the risk of freezing exists, you must completely drain
the water that has remained in the machine. Turn off the water tap, disconnect the water inlet hose
from the tap and allow the interior water to drain.
33
Here For You
After-sales assistance
If you continue to experience problems with your Integrated Dishwasher, please call the Montpellier customer
service helpline on: 03333 234 473.
Please have all your product details available, including the model number, serial number, date of purchase,
and your retailer’s details before registering a fault.
The service call cannot progress without this information.
Your 2 year Manufacturer’s guarantee
THIS DOES NOT AFFECT YOUR STATUTORY RIGHTS.
Your new Montpellier appliance carries a free guarantee which protects you against the cost of repairs during the
first 24 months from date of purchase provided that:
Any claim is accompanied by evidence of the model reference, model serial number and proof of purchase, such
as a Sales Receipt, showing that the appliance was purchased within the 24 months prior to the date
of claim.
•Any appliance not correctly installed and operated in accordance with the manufacturer’s instructions.
•Any appliance that is used for anything other than domestic purposes.
•Any defect caused by accident, misuse, unauthorised modification or inexpert repair.
•Cost of Call-out where a fault cannot be found with the appliance.
•Cost of Call-out for work covering routine maintenance, such as, but not exclusively, cleaning of filters or
defrosting.
•Cost of Call-out for work required to correct the alignment of doors following door reversal procedures carried
out by you.
•Use of the appliance by anyone other than the Householder.
•Use in any commercial environment.
•Consumable items, such as, but not exclusively, fuses in plugs, bulbs and breakable items which require
routine replacement.
•Repair costs incurred that have not been authorised by Repairtech and/or carried out by a non-approved
Repairtech engineer.
YOUR GUARANTEE IS VALID ONLY IN THE UK.
To register your appliance simply complete the card in your appliance pack and return it with a stamp affixed or
alternatively you can register online at www.montpellier-appliances.com/support
SERVICE HELP-LINE
Should your appliance develop a fault, please call the Montpellier customer service helpline on: 03333 234 473.
Please remember to have all your product details available, including the model number, serial number, date of
purchase and your retailer’s details before registering a fault.
Your service call cannot progress without this information.
Here For You
What is not covered under the Guarantee
Montpellier Domestic Appliances Ltd.
Unit 1, Tewkesbury Retail Park, Northway Lane,
Tewkesbury, Gloucestershire GL20 8JU
www.montpellier-appliances.com
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you purchased the product.