Technaxx® * User Manual
Bluetooth LED Record & CD Digitizer TX-94
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares that this device,
to which this user manual belongs, complies with the essential requirements of the
standards referred to the Directive RED 2014/53/EU. The Declaration of Conformity you
find here: www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before using
the device the first time, read the user manual carefully.
Service phone No. for technical support: 01805 012643 (14 cent/minute from German
fixed-line and 42 cent/minute from mobile networks).
Free Email: support@technaxx.de
Keep this user manual for future reference or product sharing carefully. Do the same with
the original accessories for this product. In case of warranty, please contact the dealer or
the store where you bought this product. Warranty 2 years
Before usage
Choose the installation location of your unit carefully. Avoid placing it in direct sunlight or
close to a source of heat. Also avoid locations subject to vibrations and excessive dust,
heat, cold or moisture.
Do not install the unit in a inclined position, It is designed to be operated in a horizontal
position only.
If the unit is brought directly from a cold to a warm location, moisture may condense
inside the player, and cause damage it. When you first install the unit, or when you move it
from a cold to a warm location, wait for 30 minutes before operating the unit.
The ventilation holes should not be covered. Make sure there is enough space above
and beside the amplifier/receiver. Do not place a CD player or other equipment on top of
the device.
Do not open the cabinet. This might cause a damage to circuitry or electrical shock.
If you are not going to use the player for long time, be sure do disconnect the player
from the AC power source. When removing the power plug, never yank the cord.
To prevent fire or shock hazard, disconnect your unit from the AC power source when
cleaning. Use caution when cleaning and wiping the plastic parts. Do not attempt to clean
the unit with the chemical solvents as this might damage the finish.
Features
Digitizing vinyl records & CDs to USB up to 32GB
Recording of built-in FM radio & external devices via AUX-IN connection
Music playback & recording via Bluetooth
No computer/notebook required
Pulsating LED lighting effects on the front panel
Built-in 2x 5W stereo loudspeakers
2x 1.8W RCA output for connection to HiFi systems
Record player with automatically stop & 3 speeds: 33, 45, 78 RPM
AUX–IN 3.5mm jack & headphone jack
LED display with keys background lighting
Functional and easy handling
Technical specifications
Bluetooth
Mode
Loudspeakers (built-in)
Frequency range
CD drive
Recording
Music playback
Mechanics
Input power
Output power
Connections
USB drive (FAT32)
Turntable speed
Material
Weight / Dimensions
Package Contents
V2.1 / profil A2DP & HFP
distance ~10m open areas
Phono, CD, FM, USB, AUX–IN, Bluetooth
2x 5W stereo (5x9cm), SNR ≦ 80dB, impedance 4Ω
(speakes) 80Hz–15kHz
Playback of CD, CD-R and CD-RW
MP3 music files on USB (up to 32GB)
from USB up to 32GB (MP3/WAV/WMA music files)
Belt-drive and semi-automatic play tone pickup arm
Ceramic stereo cartridge with sapphire stylus
Removable semi transparent plastic dust cover
AC 100-240V/0.8A
DC 12V/2A
AUX–IN 3.5mm jack & headphone jack
2x 1.8W RCA output (left & right channel)
USB port
32GB maximum
33, 45, 78 RPM
MDF + PVC + Plastic
3.62kg / (L) 34.2 x (W) 31.7 x (H) 17.0cm
Bluetooth LED Record & CD Digitizer TX-94, Adapter for Single
records with 45 RPM, Euro power adapter, User Manual
Front View & Rear View & Top View
1
3
4
5
6
7
8
Tuning knob for FM frequency
Standby indicator
Standby button
Function button
PREV button (fast backwards)
NEXT button (fast forwards)
PLAY/PAUSE button
2
9
10
11
12
13
14
USB port
STOP button
REC button
Bluetooth indicator
REC indicator
Open/Close CD slot
Volume control knob (VOLUME)
15
16
17
18
Antenna
Headphone port (3.5mm)
AUX–IN port (3.5mm)
RCA output socket
19
20
21
Light switch ON/OFF
Power switch ON/OFF
DC 12V power jack
Top View
22
23
24
25
45 RPM adapter
Turntable platter
Speed selector
Tone arm
26
27
28
AUTO STOP switch
ON/OFF switch
Tone arm lock
Tone head
Installation
CAUTION: To avoid stylus damage, make certain the included stylus guard is in place
whenever the turntable is being installed, moved, no being used or cleaned.
Tone Head
1
2
3
Stylus (“Needle”)
Stylus assemply
Stylus guard
Power On/Off
Firmly and securely insert the DC plug of the adapter to the DC–IN Jack [21] on the back of
the unit, and AC plug of the adapter into a power socket. Switch the power ON/OFF switch
to ON [20].
Note:
Function switch order: FM radio
CD playback USB playback
Vinyl playback
(PHO)
AUX in playback (AU)
Bluetooth (bt)
All recordings are only on USB Stick to record, not on CD or Vinyl. The format will be
MP3 with 128kBit/s (1 minute uses ~1MB of storage space).
When the switch [19] for the lighting effects is set to ON, the LED light (front panel of the
device) will be lighting in different colors when music is played.
Recording preparation
Formate a USB flash drive (max. 32GB) with your PC to FAT32. Plug this USB flash drive
into the USB port of the TX-94. Now you can start the recordings.
Listen to FM radio
Press "Standby" button [4] to turn on the unit
from above, not from the front. Press
"Function" [5] Fm radio mode is default. Then, press "Play/Pause" button [8] for 5 seconds.
It will auto scan all radio stations and save into program (e.g. P01, P02, etc). Then press
"Forward" [7] or "Previous" [6] to select the programmed station. Turn the "Tuning" [1] knob
to fine tone the radio station if the reception is not clear or to search for the FM radio station
manually. Plug in the USB flash drive to the USB port [2] at the front side of the unit.
Press the REC button [10]. The REC indicator [12] will light up green and the radio program
will be recorded to the USB flash drive. Press the REC button [10] again to save the
recorded file. REC indicator [12] will turn off.
Playing a CD
Press the “function” button [5] to enter into the CD mode; press OPEN/CLOSE button [13]
to open the disc tray, place disc label side up on the tray, press OPEN/CLOSE button [13]
to close the tray; press the PLAY/PAUSE button [8], the disc will start playing once loaded.
To pause playback press the PLAY/PAUSE button [8], to continue playback press
PLAY/PAUSE button [8] again. To stop playback press “STOP” button [9]. To skip
backwards through tracks, press PREV button [6]. To skip forwards through tracks press
NEXT button [7].
Press the REC button [10]. The REC indicator [12] will light up green and the CD will be
recorded to the inserted USB flash drive. Press the REC button [10] again to save the
recorded file. REC indicator [12] will turn off.
Playing from USB drive
Press the FUNCTION button [5] to enter into the USB mode; playback it will start
automatically. To pause playback press the PLAY/PAUSE button [8], to continue playback
press PLAY/PAUSE button [8] again. To stop playback, press STOP button [9]. To skip
backwards through tracks, press PREV button [6]. To skip forwards through tracks press
NEXT button [7].
Playing via Bluetooth
Press the function button [5] to enter into the Bluetooth mode. The Bluetooth indicator [11]
becomes blue color, starts flashing and you hear a Beep tone.
Turn on your Bluetooth function on your mobile phone or tablet PC and then search the
turntable player with its name “TX-94”. After pairing and connection, the Bluetooth
indicator [11] will become blue and stops flashing. Now you can play music of your mobile
phone or tablet PC via Bluetooth connection. For playback press the PLAY/PAUSE button
[8], to pause playback press PLAY/PAUSE button [8] again. To stop playback, press STOP
button [9]. To skip backwards through tracks, press PREV button [6]. To skip forwards
through tracks press NEXT button [7]. To disconnect the Bluetooth connection, press and
hold STOP button [9].
Press the REC button [10], the REC indicator [12] will light up green and the Bluetooth
music will be wireless recorded to the USB flash drive. Press the REC button [10] again to
save the recorded file. REC indicator [12] will turn off.
Playing a vinyl record
Before playing a record please unlatch the Tone Arm Lock [27] and remove the stylus
guard from the stylus needle. Press the function button [5] to enter into the PHONO mode;
place the record on the turntable [23], select the speed required using the Speed Selector
[24], then gently place the needle on the record, the turntable will start spinning when the
Tone Arm [25] is in position.
Besides the Speed selector, there is an AUTO STOP ON/OFF Switch [26] besides the
Speed selector [24]. If the AUTO STOP ON/OFF Switch is turned ON, the record will stop
automatically when finished (for some few vinyl records, it will stop when it does not come
to the end or it will not stop when it comes to the end). If Auto Stop is turned OFF, record
will NOT stop automatically when finished, it will continues to turn.
Press the REC button [10], the REC indicator [12] will light up green and the vinyl records
will be recorded to the USB flash drive. Press the REC button [10] again to save the
recorded file. REC indicator [12] will turn off.
AUX–IN Jack
To listen to an external source, such as a MP3 player or Smartphone, connect a suitable
cable (3.5mm jack to 3.5mm jack) to the AUX–IN socket [17] at the back of this unit, and
press the function button [5] to enter into the AUX–IN mode.
Press the REC button [10], the REC indicator [12] will light up green and the external
source will be recorded to the USB flash drive. Press the REC button [10] again to save the
recorded file. REC indicator [12] will turn off.
Attention: The volume from external devices is not loud enough. You must increase the
volume from your external device.
Headphone connector
Connect your headphone to the headphone socket [16] to enjoy music via headphone.
RCA output for external loudspeaker
The red RCA output is the right audio channel; the white RCA output is the left audio
channel. Connect one side of the RCA connection cable* (*not included) to a stereo system
or an amplifier with loudspeaker and the other side to your RCA outputs of the TX-94. Now
you can listen to music played by your TX-94 over your audio home system.
How to replace the needle
Removing the needle from the tone head: Place a screwdriver at the tip of the needle
head and push downwards in the direction illustrated by “A”. Remove the needle head shell
by pulling it forwards and pushing downwards.
Inserting the needle from the tone head: Hold the tip of the needle head shell and
insert it by pressing in the direction illustrated by “B”. Push the needle head shell upwards
in the direction illustrated by “C” until the needle locks into the tip position.
Guide Pins (inside)
Important Hints
Unpacking and handling
Open the carton carefully and remove the packing. Remove the poly-bag and retain all
packaging for future use. Keep all packaging away from small children and animals.
Positioning the music centre
Place the equipment on a stable surface, away from any heat sources, and ensuring
adequate ventilation around the music centre.
Ventilation and heat sources
Do not place material over any ventilation slots during use, this will cause the device to
overheat and fail. Do not place the device in direct sunlight or near heat sources such as
radiators or fires.
Candles and open flames
Do not place lighted candles or tea lights on top of, or at the sides of the music centre. Do
not allow any naked flames near the cabinet.
Connections
When connecting the music centre to the mains supply, do not place wires that can be
tripped over. Do not trap or place heavy objects on the mains lead.
Moisture
Do not place the equipment in wet or damp conditions, such as steamy kitchens,
bathrooms or basements. Do not allow water or other fluids to enter the equipment. Do not
touch the mains plug or adaptor with wet hands. Should moisture enter the music centre,
disconnect from the power supply.
Cleaning and care
Disconnect the music centre from the mains power supply. Use a soft dry cloth, or for
stubborn stains use a soft cloth with a dilute mild detergent. Do not use alcohol-based fluids
or abrasive materials.
Important Safeguards / Warnings / Maintenance
Do not use this unit for anything other than its intended to use.
Do not drop/
bump/shake the device (do not use the unit if it has been damaged in any way). Do not
open/repair/disassamble the device
Do not store the device in high temperature
environment/close to open fire/in humid-damp-erosive environments/into water.
Stop
using when unusual smell/heating distortion/color-change of the shell material or other
abnormal situation happens. Keep away from children/persons without enough mental
ability/persons without enough knowledge to use this product.
Hints for Environment Protection: Packages materials are raw
materials and can be recycled. Do not disposal old devices or
batteries into the domestic waste. Cleaning: Protect the device from
contamination and pollution (use a clean drapery). Avoid using rough,
coarse-grained materials or solvents/aggressive cleaner. Wipe the
cleaned device accurately. Distributor: Technaxx Deutschland
GmbH & Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany