Motion Sensor
The JAQX Motion Sensor alarms when motion is sensed or when
the external contact is opened. It is battery powered and requires
no installation tools. A Pyroflex™ sensor with HighBar™ signal
processing allows for industry-leading pet immunity and catch
performance.
Features
• Supports both motion zone and an external contact zone
• Mountable on walls or in corners
• 5 year warranty
Enroll
• Place the JAQX Smart Hub into wireless enrollment mode by
pressing the external red button for 3 seconds until hub
beeps.
• Send an enrollment signal from the motion sensor by
removing the battery tab or removing the cover to trip a
tamper. NOTE: The battery tab is located inside the motion
sensor. To open the cover, press the button latch on bottom
of sensor.
• Confirm that the motion sensor has been properly enrolled by
checking for new zone on your JAQX App or in your customer
portal.
• Once the sensor has been enrolled on your system, turn off
sensor enrollment by pressing the external button on the
JAQX smart hub for 3 seconds or until hub beeps.
• Call JAQX customer support to rename your sensor
Mounting Screw Holes
Installation
Use the included 3M VHB® tape to adhere the motion sensor on a wall or in a corner.
The tape should be applied to the back when wall mounting or to the back bevels when
corner mounting. Alternatively, screw mounting can be done by punching out the screw
mounting holes.
Installation Tips
• Mount 7.5 to 9.5 feet from the floor for an optimal balance between catch
performance and pet immunity.
• Remove the cover and circuit board before trying to punch out the screw mounting
holes.
• Ensure the bug foam stays intact and snug around the IR sensing element when
re-installing the circuit board.
Ceiling
Floor
Cover-Securing Screw Hole
Walk Test
To test your motion sensor, press the sensor's
tamper button.The walk test lasts three minutes.
Walk Test LED
Walk Test Operation
• After pressing the tamper button, the walk test
red LED light turns on when motion is sensed.
• When the red light comes on (detecting motion)
The motion sensor performs a re-calibration that
takes about 30 seconds. The sensor will NOT
sense motion during the re-calibration. During
this time walk out of range of the motion sensor.
• After 30 seconds, walk back into range of the
sensor. The LED will come on when detecting
motion.
• IMPORTANT - Once the Walk Test has ended,
the red LED light will not come on when
detecting motion. This is to help conserver
battery life of sensor.
Cover Tamper Switch
Bug Foam IR Sensing Element
Low - Jumper ON
High - Jumper OFF
Sensitivity
Battery
3M VHB Tape works great if the surface is
properly prepared and firm pressure is applied for
over 10 seconds. Ensure e the mounting surface
temperature is above 50 °F
External Contact
Motion lockout is active for three minutes after a motion event is detected. During
themotion lockout period, motion events will be ignored.
Motion sensitivity can be adjusted by the sensitivity jumper on the circuit board.
• Jumper Installed (lower sensitivity): Detects person in 3 to 5 steps. Increases pet
immunity. Usually for security applications.
• Jumper NOT Installed (higher sensitivity): Detects person in 2 to 4 steps. Usually for
occupancy applications.
Pet immunity is optimized when the motion sensor is mounted at 7.5 to 9.5 feet high and
aimed away from house features that could allow pets to be high in the detection field (e.g.
stairs, counter tops, tall furniture).
7.5ft
3.2ft
0
0
10ft
20ft
30ft
40ft
Motion catch performance is best when the motion sensor is positioned so a person
would typically walk across the front of the motion sensor instead of directly toward the
motion sensor.
Motion Detection Tips
• Provide a clear line-of-sight to the monitored area and remember that glass blocks
infrared energy (PIR = Passive InfraRed).
• Aim away from windows and sunlight.
• Aim away from air conditioners, heaters or heating/cooling vents.
Specifications
Side field of view for a mounting height of 7.5 feet
7.5ft
3.2ft
0
20ft Side
10ft
30ft
40ft
30ft
40ft
field of view for a mounting height of 9.5 feet 9.5ft
6.4ft
3.2ft
0
10ft
20ft
Top field of view
0
10ft
20ft
30ft
40ft
30ft
20ft
10ft
0
10ft
20ft
30ft
Specifications
Physical
Housing Dimensions
3.50 x 2.40 x 1.70 inches (8.9 x 6.1 x 4.3 cm)
Weight with Battery
3.2 ounces (91 grams)
Mounting Fastener
3M VHB (Very High Bond) Tape or Screws (both provided)
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specifications
Frequency
433.92 MHz
Pet Immunity
Two 60-pound dogs or one 85-pound dog
Replacement Battery
One Panasonic CR132A
Nominal Battery Life
6 to 8 years
Battery Voltage
3.0 VDC (Nominal), 2.2 VDC (Low)
Current Draw
30 mA (Maximum), 20 uA (Quiescent)
Optimal Mounting Height
7.5 to 9.5 feet (2.3 to 3.0 m)
Transmitted Indications
Cover Tamper, Low Battery, Supervision
Certification
RE610P
UL639, ULC-S309-03, ETL, FCC, IC
RE610P-CE
EN 50131-2-2, EN 60950-1, EN 300 220, EN 301 489,
CE Security Grade 1, CE Environmental Class 2, RCM
Specifications subject to change without notice