Order parts online www.follettice.com

U150 Series

Ice Dispensers

Operation, Service and Parts Manual

U150N U150NR4A/W

U150NR5A/W

U150NR8A/W

U150NR10A/W

U150

U150B

U150R4A/W

U150R5A/W

U150BR4A/W

U150BR5A/W

U150R8A/W

U150R10A/W

U150BR8A/W

U150B10A/W

801 Church Lane • PO Box D, Easton, PA 18044

Toll free (800) 523-9361 • (610) 252-7301

Fax (610) 250-0696 • www.follettice.com

206563R02

Welcome to Follett

Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that you take a moment to review this manual before using the dispenser. Should you have any questions or require technical help at any point, please call our technical service group toll free at (800)523-9361 or

(610)252-7301.

Before you begin

Check your paperwork to determine which model you have. Following is an explanation of the different model numbers in the U150 series.

U150BR5A

Condenser type – A = air-cooled, W = water-cooled

Remote icemaker(s) capacity and refrigerant – 4 = 400 lbs (181kg)/day, R12;

5 = 400 lbs (181kg)/day, R22; 8 = 800 lbs (363kg)/day, R12; 10 = 800 lbs

(363kg)/day, R22

B = with integral beverage cooling. Absence of a B = no integral beverage cooling. N = no beverage rail or valves.

Approximate storage capacity in lbs

Dispenser configuration – U = undercounter

Important cautions

• Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If access to this area is required, power to unit must be disconnected first.

• Follett manual load units can accommodate most cube/cubelet ices up to 1" square, or Follett compressed nugget ice. Crushed, flake, bagged, nugget or congealed ice cannot be used. Use of these ices can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to dispenser. If you have any questions concerning your ice type, please call

Follett’s customer service group toll free at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301.

• Follett recommends use of an activated carbon filter for units equipped with icemakers

• Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.

• Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

Electrical specifications

Standard electrical - 115V, 60Hz, 1 phase

Separate circuit and disconnects required for each icemaker and dispenser. Max. fuse size 20 amps per circuit

Manual load models

U150N – dispenser 2.4 amps

U150 – dispenser 2.4 amps

U150B – dispenser 4.4 amps

Models with R4A/W Icemaker

U150R4A/W, U150NR4A/W – 13.4 amps

U150BR4A/W – 15.4 amps

U150R8A/W, U150NR8A/W – 24.4 amps

U150BR8A/W – 26.4 amps

Models with R5A/W Icemaker

U150R5A/W, U150NR5A/W – Icemaker 11.0 amps, dispenser 2.4

amps

U150BR5A/W – Icemaker 11.0 amps, dispenser 4.4 amps

U150R10A/W, U150NR10A/W – (2) icemakers 11.0 amps each, dispenser 2.4 amps

U150B10A/W – (2) icemakers 11.0 amps each, dispenser 4.4

amps

• Equipment ground required.

• Separate circuit and disconnects required for each icemaker and dispenser. Disconnects suggested within 10 ft (3m) of dispenser and icemaker(s).

2

Alternate electrical - 230V, 50Hz, 1 phase

Separate circuit and disconnects required for each icemaker and dispenser. Max. fuse size 15 amps per circuit

Manual load models

U150N – dispenser 1.7 amps

U150 – dispenser 1.7 amps

U150B – dispenser 2.2 amps

Models with R4A/W Icemaker

U150R4A/W, U150NR4A/W – 7.7 amps

U150BR4A/W – 8.2 amps

U150R8A/W, U150NR8A/W – 13.7 amps

U150BR8A/W – 14.2 amps

Models with R5A/W Icemaker

U150R5A/W, U150NR5A/W – Icemaker 6.0 amps, dispenser 1.7 amps

U150BR5A/W – Icemaker 6.0 amps, dispenser 2.2 amps

U150R10A/W, U150NR10A/W – (2) icemakers 6.0 amps each, dispenser 1.7 amps

U150B10A/W – (2) icemakers 6.0 amps each, dispenser 2.2

amps

Plumbing

Dispenser – all models

3/4" female PVC slip joint dispenser drain

3/4" male slip joint to 3/4" MPT PVC adapter provided

Note: Drains to be hard piped and insulated, with1/4" per foot (6mm per 30.4cm) min. slope.

Icemaker – automatic load models only

1/4" FPT water in

1/2" MPT drain

3/8" FPT condenser inlet (water-cooled condenser only)

1/2" FPT condenser drain (water-cooled condenser only)

Note:

Water disconnect within 10 feet (3m) of icemaker(s) is suggested for automatic load units.

Beverage connections - Models with beverage valves only

1/4" syrup and 3/8" carbonated water pigtails.

How the dispenser works

Follett’s U150 series ice dispensers are available in manual load configurations (using ice from another source) or automatic load configurations, fed from one or two Follett 400 lb (181kg)/day remote icemakers.

In all models, ice is stored below the counter in the dispenser storage area. When the dispense lever or button is pushed, the dispense motor is activated. This causes the wheel assembly in the storage area to turn, moving ice to the vertical auger assembly, which carries ice up to the dispense chute where it drops by gravity into the container.

In automatic load models, ice is manufactured in either one or two Follett remote icemakers. These icemakers may be located up to 20 feet (3m) away from the dispenser. As water freezes to the inside walls of the icemaker evaporator, a rotating stainless steel auger removes ice and carries it to the top of the evaporator assembly where it is compressed and extruded through an outlet port. The extruded ice is then pushed through the tube to the storage compartment of the dispenser. A level fill circuit maximizes fill in the storage area by rotating the wheel at intervals until the bin is completely filled. When the bin is filled, a bin stat shuts the icemaker off to avoid overfilling of the bin. U150 dispensers equipped with R4A/W (R12 refrigerant) icemakers have a safety thermostat that prevents the icemaker from restarting for 15 to 30 minutes after the bin stat has shut the icemaker down. In U150 dispensers with R5A/W (R22 refrigerant) icemakers, the icemaker will restart after 15 to 20 minutes if the bin is calling for ice.

From Serial Number 40600 and up, models with integral ice-waterbath beverage cooling are equipped with a waterbath timer circuit that activates the waterbath pump 1 minute on and 10 minutes off to ensure optimal beverage cooling.

To start-up and operate dispenser

1. Follow cleaning instructions in U150 Series Installation Manual before operating dispenser.

2. Follow start-up instructions in U150 Series Installation Manual for beverage line hook-up instructions, initial loading of ice-waterbath beverage cooling system, manual loading restrictions and/or automatic load start-up requirements.

3. Turn power and feed switches located inside beverage rail or ice tower to ON position.

4. For manual load models, remove front drain pan or rear lid and fill storage area with compatible ice.

5. For automatic fill models, turn icemaker (bin signal) switch(es) located inside beverage rail or ice tower to ON position and begin to make ice.

6. When dispenser has at least 6" (153mm) of ice in storage area, press PUSH FOR ICE lever or button to insure that dispenser is operating properly.

3

Periodic cleaning of dispenser

Caution: Do NOT run plastic parts (drain pan, dispense chute cover, dispense wheel) through a dishwasher.

Solution A: Prepare a cleaning solution (200 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be 75˚ to 125˚F (24˚ to 52˚C).

Solution B: Prepare a sanitizing solution (50 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be 75˚ to 125˚F (24˚ to 52˚C).

Recommended daily cleaning of drain pan

1. Remove all debris from drain pan.

2. Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear.

Recommended weekly cleaning

1. Remove drain pan and grille and wash with Solution A above. Rinse thoroughly.

2. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall.

3. Pour a solution of one cup (8oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain pan to help prevent algae growth in drain lines.

Recommended quarterly cleaning (every 3 months)

Caution: Remove dispense switch from dispense chute before cleaning chute.

1. Turn power switch to OFF position.

2. Remove ice from storage area.

3. Remove dispense chute, chute cover, auger tube and auger (page 10).

4. Remove drain pan, grille, dispense wheel and waterbath cover plate (page 11).

5. Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize with Solution B.

6. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall.

7. For units without integral beverage cooling, clean area below wheel and stainless cover plate with Solution A, rinse and sanitize with Solution B.

8. For models with integral ice-waterbath beverage cooling only:

• Lower drain tube found on utility connection side of dispenser and drain ice-waterbath

• Use a bottle brush to clean coils with Solution A, rinse and sanitize with Solution B

• Reposition waterbath drain line in UP position

• Pour 3.5 gallons (13L) Solution A into waterbath

• Turn power ON and tape dispense lever or dispense button back in “Dispense” position

• Allow pump to run for 2 minutes to clean pump and pump lines

• Turn power OFF and remove tape

• Drain bath and replace drain tube in UP position to avoid siphoning waterbath water

Putting unit back in service after quarterly cleaning

1. On units with integral beverage cooling, fill ice-waterbath with 3.5 gallons (13L) potable water.

2. Reassemble components.

3. For manual load units, fill unit with an approved ice (page 2).

4. For automatic load units with R4A/W (R12 refrigerant) icemakers, turn icemaker switch(es) and dispenser power switch to ON position and allow storage area to fill.

5. For automatic load units with R5A/W (R22 refrigerant) icemakers, turn bin signal switch(es) and dispenser power switch to ON position and allow storage area to fill.

6. Push dispense button or lever to test that dispenser is functioning properly.

Quarterly cleaning of icemaker system

Units equipped with icemakers require cleaning of icemaker system at least every three months, and more often if local water conditions dictate. Failure to clean icemaker system will result in decreased performance and potential damage to icemaker. Refer to Icemaker Operation and Service Manual.

4

All manual load models before serial #40600

POWER SUPPLY

PURPLE

WATERBATH

T-STAT

UNITS WITH BEVERAGE COOLING ONLY

KEY SWITCH

(OPTION)

BLACK

WHITE

WHITE

N

BLACK

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

BROW

24V TRANSPORMER

AUGER

YELLOW

DISPENSE

SWITCH

YELLOW

M

WATERBATH

PUMP

M

24V TO

BEVERAGE

VALVES

BLACK

WHITE

YELLOW

FEED

SWITCH

YELLOW

RED

WHEEL

MOTOR

M

BLUE

WHITE

Automatic load models with R4A/W (R12) icemaker(s), no beverage cooling –

Before serial #40600

POWER SUPPLY

KEY SWITCH

(OPTION)

BLACK

3

2 1

LEVEL FILL

TIMER

18 MIN OFF

5 SEC ON

24V TO

BEVERAGE

VALVES

WHITE

BROWN

WHITE

24V TRANSPORMER

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

YELLOW

DISPENSE

SWITCH

YELLOW

AUGER

M

BLACK #6

PURPLE

BLACK #8

WHITE

9

7

4

1

YELLOW

ORANGE

6

3

YELLOW #7

FEED

SWITCH

YELLOW

RED

WHITE

BLUE

WHEEL

MOTOR

WHITE

WHITE #4

T-STAT

RED #2

ICE SUPPLY

SWITCH #1

RED #1

TO ICEMAKER #1

RED #2

ICE SUPPLY

SWITCH #2

RED #2

DUAL FEED RELAY

(OPTIONAL)

5

TO ICEMAKER #2

Wiring Diagram – Automatic load models with R5A/W (R22 refrigerant) icemaker (s), no beverage cooling – Before serial # 40600

POWER SUPPLY

KEY SWITCH

(OPTION)

BLACK

3

2 1

LEVEL FILL

TIMER

18 MIN OFF

5 SEC ON

24V TO

BEVERAGE

VALVES

WHITE

BROWN

WHITE

24V TRANSPORMER

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

YELLOW

DISPENSE

SWITCH

YELLOW

AUGER

M

BLACK #6

PURPLE

BLACK #8

WHITE

9

7

4

1

YELLOW

ORANGE

6

3

YELLOW #7

FEED

SWITCH

YELLOW

RED

WHITE

BLUE

WHEEL

MOTOR

WHITE

WHITE #4

T-STAT

RED #2

ICE SUPPLY

SWITCH #1

RED #1

TO ICEMAKER #1

BIN LEVEL CONTROL

RED #2

ICE SUPPLY

SWITCH #2

RED #2

TO ICEMAKER #2

BIN LEVEL CONTROL

6

Automatic load models with R4A/W (R12) icemaker(s), with beverage cooling –

Before serial #40600

POWER SUPPLY

BLACK

KEY SWITCH

(OPTION)

WHITE

BROWN

WHITE

24V TRANSPORMER

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

YELLOW

DISPENSE

SWITCH

YELLOW

AUGER

M

PURPLE

BATH

T-STAT

PURPLE

PUMP

M

WHITE

WHITE

24V TO

BEVERAGE

VALVES

BLACK #6

BLACK #8

3

2

1

LEVEL FILL

TIMER

18 MIN OFF

5 SEC ON

T-STAT

RED #2

ICE SUPPLY

SWITCH #1

9

7

4

1 YELLOW

ORANGE

6

3

YELLOW #7

FEED

SWITCH

YELLOW

RED

BLUE

WHITE

WHITE #4

WHEEL

MOTOR

WHITE

RED #1

TO ICEMAKER #1

RED #2

ICE SUPPLY

SWITCH #2

RED #2

DUAL FEED RELAY

(OPTIONAL)

TO ICEMAKER #2

7

Automatic load models with R5A/W (R22) icemaker(s) and beverage cooling –

Before serial #40600

POWER SUPPLY

KEY SWITCH

(OPTION)

BLACK

WHITE

BROWN

WHITE

24V TRANSPORMER

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

YELLOW

DISPENSE

SWITCH

YELLOW

AUGER

M

PURPLE

BATH

T-STAT

PURPLE

PUMP

M

WHITE

WHITE

24V TO

BEVERAGE

VALVES

BLACK #6

BLACK #8

3

2 1

LEVEL FILL

TIMER

18 MIN OFF

5 SEC ON

T-STAT

RED #2

ICE SUPPLY

SWITCH #1

RED #1

9

7

4

1

YELLOW

ORANGE

6

3

YELLOW #7

FEED

SWITCH

YELLOW

RED

WHITE

BLUE

WHEEL

MOTOR

WHITE

WHITE #4

TO ICEMAKER #1

BIN LEVEL CONTROL

RED #2

ICE SUPPLY

SWITCH #2

RED #2

TO ICEMAKER #2

BIN LEVEL CONTROL

8

All Models – serial #40600 and up

POWER SUPPLY

BLACK

BATH

TIMER

1 MIN ON

10 MIN OFF

1

2 3

WHITE

BLACK

BATH

RELAY

R2

WHITE

BLACK

POWER

SWITCH

BLACK

DRAIN PAN

SWITCH

BLACK

LID

SWITCH

DISPENSE

SWITCH

YELLOW

YELLOW

AUGER

MOTOR

M

BLACK

WHITE

BLACK #14

BIN LEVEL

T-STAT

ICEMAKER #1

SWITCH

RED

ICEMAKER #2

SWITCH

RED

Legend

Beverage cooling option

Autofill option

RED

WHEEL

MOTOR

R1

YELL #7

FEED SWITCH

YEL BLUE

BLK

M

BLACK #6

PURPLE #1

BIN LEVEL

FILL TIMER

18 MIN OFF

5 SEC

1

ON

2 3

WHITE #4

R1

BLACK #8

BLACK #1

R1

LEVEL FILL RELAY

PURPLE

BROWN

R2

BLACK

BLACK

KEYLOCK SWITCH

(OPTION)

R2

ORANGE

WHITE #9

PURPLE

BATH MOTOR

M

WHITE

PRI

WHITE

TRANSFORMER

WHITE

SEC

V

V V V

SODA

VALVES

V

V

V

V

WHT

24V

9

Instructions for disassembly required for periodic cleaning

Dispense chute cover removal

1. Remove ice tower cover.

2. Push in on both sides of black plastic chute cover to clear upper and lower pins.

3. After clearing pins, pull chute cover forward to remove.

Dispense chute assembly removal

1. Remove chute cover (see instructions at left).

2. Remove thumbnut holding dispense chute assembly and pull assembly forward.

3. Disconnect electrical connector and pull dispense chute assembly free of tower.

Auger motor and bracket removal

1. Remove dispense chute cover and dispense assembly (see above).

2. Remove two rear thumbnuts on motor bracket.

3. Lift motor bracket up and unplug electric quick disconnects.

4. Remove motor and bracket assembly.

10

Auger and auger tube removal

1. Remove auger motor and bracket assembly (see instructions at left).

2. Pull auger upward to clear auger tube.

3. Remove auger tube bearing plate located on bottom of auger tube.

4. Lift auger tube upward to clear dispenser top.

Dispense wheel and waterbath bath cover removal

1. Remove grille and drain pan assembly.

2. Remove center thumbnut and threaded rod on dispense wheel assembly and lift wheel out front (see photo above).

3. Remove two (2) screws holding bath cover in place and lift cover out front.

Disassembly instructions for service requirements only – NOT required for any cleaning procedure.

Wheel motor removal

1. Remove dispense wheel and ice-waterbath cover plates (see instructions above).

2. Remove spacer and shaft seal.

3. Lift motor bracket up and unplug electric quick disconnects.

Ice-waterbath pump motor removal

1. Remove wheel motor.

2. Drain ice-waterbath by lowering drain tube on utility connection side of dispenser.

3. Slice insulation enough to expose hose clamps on intake, output and recirculating system fittings.

4. Loosen clamps and pull tubing off fittings.

5. Loosen screws on pump motor bracket.

6. Slide pump bracket off mounting screws.

7. Disconnect electric wires from pump and remove pump.

11

Service and parts

Before calling for service

1. Check that ice is in dispenser and that congealed cubes are not causing a jam.

2. Check that circuit breaker and switches are in ON position.

3. Check that front drain pan and rear lids are on securely. If ajar, neither dispenser nor valves will operate.

4. Check that all drains are clear.

5. For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service Manual for service and troubleshooting information.

Dispenser troubleshooting guide

Symptom

Ice does not dispense when switch is actuated.

• Auger motor does not run

• Wheel motor does not run

Possible cause Solution

1. Dispense chute out of position or faulty dispense switch.

2. Front drain pan or rear lid ajar.

3. Faulty lid safety switch or drain pan switch.

4. Power switch faulty or in OFF position.

1. Check that dispense chute lever contacts dispense switch rod, or replace switch.

2. Check drain pan and rear lid.

3. Check lid safety switch and drain pan switch.

4. Check power switch.

Ice does not dispense.

• Auger motor does not run

• Wheel motor runs

Ice does not dispense.

• Auger motor runs

• Wheel motor does not run

Warm drinks or soda foaming.

1. Faulty auger motor.

2. Chain off auger sprocket.

3. Faulty run capacitor.

1. Check auger motor.

2. Check chain and sprocket.

3. Check run capacitor.

1. Feed switch faulty or in OFF position.

2. Faulty wheel motor.

3. Faulty run capacitor.

4. Serial #40600 and up only, faulty level fill relay.

1. Check feed switch.

2. Check wheel motor.

3. Check capacitor.

4. Check relay.

1. No ice in storage bin.

2. Water siphoned out of icewaterbath.

3. Faulty circulating pump.

4. Serial #40600 and up only, faulty bath timer.

5. Serial #40600 and up only, faulty bath relay.

1. Fill storage area with ice or check icemaker operation.

2. Check that ice-waterbath drain tube is in fixed upright position.

3. Check pump.

4. Check for output on pin #1 at 10 min. intervals.

5. Check relay.

Beverage valves not operating.

1. Faulty 24V transformer.

2. Power switch faulty or in OFF position.

3. Drain pan or lid switch faulty or not depressed.

4. Beverage key switch locking out access.

1. Check transformer.

2. Check power switch.

3. Check switch and placement of drain pan and lid.

4. Check valve lockout.

For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service Manual for service and renewal parts information.

12

U150 series with right hand tower

(shown with push-button dispense chute assembly)

1

2

4

Close up of U150 series lever dispense chute assembly

(right hand tower)

3

7

5

13

12

11

8

Reference #

1

Not shown

2

Not shown

Not shown

3

4

5

6

7

8

Not shown

Not shown

9

Not shown

Not shown

Not shown

Not shown

10

Not shown

Not shown

Not shown

11

Not shown

Not shown

12

Not shown

Not shown

13

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

9

10

Description

Top, beverage rail and tower (includes “Follett” label)

Top, beverage rail and tower (includes “Follett” label) — 10 valve models

Label, “Follett”

Label, “Follett” (U150N)

Label, “Follett”, 10 valve models

Cover, dispense chute, lever operation (with clear plastic extension)

Cover, dispense chute, push-button operation (includes button)

Label, “Ice”,

Cup guide, “Push”, lever operation only

Button, “Push for Ice”

Ice guard, plastic (includes thumbscrews)

Thumbscrews, ice guard (10-32 x 1/2)

Backsplash assembly

Drain pan and frame, RH, 6-8 valve, non-recessed grille

Drain pan and frame, LH, 6-8 valve, non-recessed grille

Drain pan and frame, RH, 6-8 valve, recessed grille

Drain pan and frame, LH, 6-8 valve, recessed grille

Drain pan, 6-8 valve, non-recessed grille

Drain pan, 6-8 valve, recessed grille

Drain pan, 10 valve, black plastic (obsolete)

Drain pan, 10 valve, gray plastic

Grill, 6-8 valve units, non-recessed grille

Grill, 6-8 valve units, recessed grille

Grill, 10 valve units, black plastic pan

Grill, 10 valve units, gray plastic pan

Cover, bin

Cover, bin – 10 valve models

Cover, ice storage (below drain pan) – all U150 models

Handle, bin cover

Switch, keylock for valves

Key, beverage lock switch

Legs, 6" (153mm) adjustable to 9" (229mm) – set of 4

Fitting, male, lower drain pan

Elbow, lower drain pan

Drain pan assembly, lower

Plug, drain clean out

Water station (glass filler) U150N only

Lid, rear (U150N)

Lid, tower (U150N)

End wrap, dispense tower, RH

End wrap, dispense tower, LH

Inside wrap, dispense tower

13

Part Number

501677

502127

501345

502341

502128

501673

501672

501344

501342

501511

501674

501100

502163

501878 & 501877

501879 & 501877

501878

501879

501877 & 501880

501880

502641

502642

501675

501877

502126

502451

501761

502129

502162

501763

501409

501286

500880

501926

501927

501928

501929

502296

502340

502342

502139

502140

502143

6

4

5

11 3

6

7

8

1

9

Reference #

1

2

3

6

7

4

5

8

9

10

11

12

Not shown

Not shown

Not shown

Not shown

12

Description

Wheel, dispense, (includes 501682 and 501679)

Lip kit, U150, front (includes adhesive)

Plate, ice distribution (includes two 501764)

Hardware, bin thermostat mounting

Retaining bracket, ice tube (includes thumbnuts)

Ice tube assembly (sold by the foot, must be ordered with 500366)

Plate, ice tube mounting

Agitator, rotating

Nut, knurled, rotating agitator (2 required)

Agitator, fixed

Lip kit, U150 and U150 – 10 valve, rear (includes adhesive)

Nut, knurled, dispense wheel (includes stud)

Plate, ice tube mounting (dual feed)

Drive bar, dispense wheel

Lip kit, U150N, rear (includes adhesive)

Cover, stainless steel, front opening, ice storage

2

10

Part Number

501681

502282

501539

501762

501764

502017

501413

501679

500905

501678

502283

501320

501412

501682

502284

502162

Reference # Description

13 Auger, vertical

14

Not shown

Auger tube, LH tower (includes 501696)

Auger tube, RH tower (includes 501696)

Not shown

Not shown

Not shown

Bearing and plate, auger tube

Part Number

501524

501670

501671

Kit, ice tube entry (to convert to opposite side) 501496

Kit, conversion (to convert 150 automatic unit to unit with dual icemakers)

501696

501521

13

14

14

1

2

4

3

Reference #

1

Not shown

2

3

Not shown

4

5

6

Not shown

Description

Spring, lever dispense mechanism (2 needed)

Dispense chute, lever operation – LH

Dispense chute, lever operation – RH

Cup guide, “Push”, lever operation

Dispense chute, push-button operation – LH

Dispense chute, push-button operation – RH

Spring, push-button dispense mechanism

Switch, dispense

Thumbnut 10-32 (secures dispense chute to front)

15

6

Part Number

501460

501688

501689

501342

501690

501691

501783

501686

500905

5

1

3

4

5

2

3

6

16

7

3

Reference #

1

2

3

4

6

7

5

5

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Not shown

Description

Thumbscrew, 10-32 x 3/4

Seal, shaft, wheel motor

Spacer, wheel motor

Cover, waterbath, beverage cooled units with foot mount motor – must upgrade with face mount casting and waterbath cover (Part number 501769)

Pump kit (includes tubing, clamps and insulation

Pump motor – non-domestic units, 230V/50Hz

Cover, waterbath, beverage cooled units with face mount motor

Cover, waterbath, non-beverage cooled units with face mount motor

Cover, waterbath, non-beverage cooled units with foot mount motor – must upgrade with face mount casting and water bath cover (Part number 501770)

Tubing kit, pump motor

Coil, syrup main

Coil, syrup, 2-6

Coil, soda

Coil, soda, lower

Grommet, rubber, for coils

Part Number

501766

501333

501768

501791

501377

501706

501705

501687

502651

502653

502655

502654

502652

17

2

3

4

7

5

6

8

1

9

11

Reference #

1

Not shown

2

Not shown

3

4

5

8

9

6

7

10

11

Not shown

Description

Motor, auger (includes gearbox and capacitor)

Part Number

501680

Motor, auger – non-domestic units, 230V, 50Hz (includes gearbox & capacitor) 501374

Capacitor, auger motor (20MFD, 370VAC) 501550

Capacitor, auger motor – Non-domestic units (4MFD, 370VAC)

Cover and bearing, chain drive

Bearing, auger, upper

Sprocket 35#, 22T 5/8 bore

501393

501695

501314

501552

Key

Chain, auger drive

Sprocket 35#, 12T 5/8 bore

Drive shaft, auger

Thrust washers (4)

Mounting plate, auger motor (includes bearing 501314)

Thumb nut 1/4 - 20 (2 needed) (secures auger motor assembly)

500367

501551

500913

501544

501765

502166

500905

18

10

3

2

4

5

1

Reference #

1

Not shown

2

Not shown

3

4

5

Not shown

Not shown

Not shown

Not shown

Description

Capacitor, wheel motor (12MFD, 370VAC)

Capacitor, wheel motor (4MFD, 370VAC)

Motor, wheel, face mount (includes capacitor)

Motor, wheel, face mount – non-domestic, 230V, 50Hz (includes capacitor)

Bracket, motor mount

Screws (4), (to secure face mount motor to motor bracket)

Seal, shaft, wheel motor

Part Number

501782

501393

501645

501648

501685

501767

501333

Spacer, wheel motor

Screws (2), 10-32x3/4, motor plate (to secure motor bracket to bin)

501768

501766

Face mount motor casting and waterbath cover for units with beverage cooling 501769

Face mount motor casting and waterbath cover for non-beverage cooled units 501770

2

1

Reference #

1

Not shown

2

Not shown

Front of dispenser

Description

Switch, lid safety – LH

Switch, lid safety – RH

Switch, safety, drain pan – LH

Switch, safety, drain pan – RH

Part Number

501338

501364

501692

501693

19

Before Serial #40600

1

2

3

Reference #

1

Not shown

2

3

Not shown

4

5

Not shown

6

Not shown

Not shown

4

Description

Transformer, 24V, 50VA

Transformer, 24V – non-domestic units, 230V, 50Hz

Thermostat, bin level

Timer, level fill (automatic fill units only)

Timer, level fill – non-domestic units, 230V, 50Hz

Switch, toggle, SPST

Relay, level fill

Relay, level fill – non-domestic units, 230V, 50Hz

Thermostat, pump – obsolete, must convert to timer kit

Timer kit (to convert pump to intermittent run circuit)

Timer kit (to convert pump to intermittent run circuit) – non-domestic units, 230V, 50Hz

5

Part Number

501321

501429

500514

501601

501700

500006

501369

501375

501867 or 501868

501867

501868

Serial #40600 and up

1 2 3

6

Reference #

1

1

2

3

4

2

3

5

5

6

Not shown

7

7

4

5

6

Description

Transformer, 24V

Transformer, 24V – non-domestic units, 230V, 50Hz

Relay, level fill

Relay, level fill – non-domestic units, 230V, 50Hz

Relay, beverage bath

Relay, beverage bath - non-domestic units, 230V, 50Hz

Thermostat, bin level

Timer, level fill (automatic fill units only)

Timer, level fill – non-domestic units, 230V, 50Hz

Switch, toggle, SPST

Switch, rocker, U150N

Timer, beverage bath

Timer, beverage bath – non-domestic units, 230V, 50Hz

7

Part Number

501321

501429

501369

501375

501369

501375

500514

501601

501700

500006

502161

501845

501846

206563R02

02/06