High Definition Hospitality LCD Display Pantalla de LCD

Operating Instructions
Manual de instrucciones
High Definition Hospitality LCD Display
Pantalla de LCD de alta definición para la industria hotelera
Model No.
Número de modelo
TH-32LRT12U
TH-37LRT12U
The illustration shown is an image.
Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference.
La ilustración mostrada es una imagen.
Antes de conectar, utilizar o ajustar este producto, lea completamente este manual de instrucciones;
y guárdelo para consultarlo en el futuro en caso de ser necesario.
English
Español
TQB4CM171
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with
arrow-head within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock
to persons.
The exclamation point within
a triangle is intended to
tell the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING:To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain
or moisture.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING:To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
This video monitor is designed to display television content from a separate TV tuner. Full-power analog TV broadcasting
in the United States will end (as required by law) on February 17, 2009, after which full-power TV broadcasts will be
digital only. If this device is used after that date to record or display programming from a product with a TV tuner that
relies on a TV antenna, that product would need to contain a digital tuner, or a TV Converter would be necessary to
tune the digital signal received with a TV antenna. Analog TVs should continue to work as before for other purposes
(e.g., for watching low-power TV stations still broadcasting in analog, watching pre-recorded movies, or playing video
games). When a Converter is used with an older television receiver or directly with this product, a signal splitter might
be necessary to continue to receive low-power analog broadcasts via an antenna. For more information, please see
www.DTV.gov or 1-888-CALL-FCC. For information on the TV Converter program, and on government coupons that
may be used toward the purchase of one, see www.dtv2009.gov, or call the NTIA at 1-888-DTV-2009. Please check
with your cable or satellite service provider if you have questions about your cable or satellite set-top box.
Important Safety Instructions
1)Read these instructions.
2)Keep these instructions.
3)Heed all warnings.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with dry cloth.
7)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11)Only use attachments / accessories specified by the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or when unused for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15)To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment
from your new LCD Display.
To obtain maximum benefit from your set, please read these Instructions before making any adjustments,
and retain them for future reference.
Retain your purchase receipt as well, and record the model number and serial number of your set in the
space provided on the rear cover of these instructions.
Table of Contents
Important Safety Instructions................................... 3
Table of Contents...................................................... 4
FCC STATEMENT....................................................... 5
Safety Precautions.................................................... 6
Maintenance............................................................... 7
Accessories............................................................... 8
Accessories Supplied............................................... 8
Remote Control Batteries......................................... 8
Location.................................................................... 9
Preparation for Wall-hanging.................................... 9
Connections............................................................. 10
AV connection.........................................................11
Component (YPbPr) connection..............................11
PC Input Terminals connection............................... 12
HDMI connection.................................................... 13
Audio Out connection............................................. 13
Serial Terminals connection................................... 14
Power ON / OFF ...................................................... 15
Using the Power Switch......................................... 15
Using the Power Button.......................................... 15
Initial selections...................................................... 16
Selecting the input signal....................................... 16
Selecting the On-Screen Menu Language............. 16
Basic Controls......................................................... 17
ASPECT Controls.................................................... 19
On-Screen Menu Display........................................ 20
Picture Menu............................................................ 22
Sound Menu............................................................. 23
Setup Menu.............................................................. 24
HOTEL MODE Setup................................................ 26
Troubleshooting...................................................... 28
Applicable Input Signals......................................... 29
Specifications.......................................................... 30
Panasonic Professional Flat Panel
Display Limited Warranty....................................... 31
LIMITED WARRANTY STATEMENT........................ 32
Customer Service.................................................... 33
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC CAUTION:
To assure continued compliance, follow the attached installation instructions and use only shielded interface
cables when connecting to computer or peripheral devices. Any changes or modifications not expressly
approved by Panasonic Corp. of North America could void the user's authority to operate this device.
FCC Declaration of Conformity
Model No. TH-32LRT12U, TH-37LRT12U
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way 1F-10, Secaucus, NJ 07094
Contact Source:
Panasonic Professional Display Company
Panasonic Plasma Concierge 1-800-973-4390
CANADIAN NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
Note:
• Image retention may occur. If you display a still picture for an extended period, the image might remain on the screen.
However, it will disappear after a while.
• Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain
readily operable.
Trademark Credits
•VGA is a trademark of International Business Machines Corporation.
•Macintosh is a registered trademark of Apple Computer, USA.
•VGA, SVGA, and XGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
•HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Safety Precautions
CAUTION
This LCD Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
•Wall-hanging bracket (angled)...................................................TY-WK32TM1
•Wall-hanging bracket ................................................................TY-WK32TM2
•ATSC Tuner for Hospitality . ......................................................Enseo DTB1510 / Enseo DTB1510 TB
•Main Board (32") .......................................................................TNM4CD0819FA
•Main Board (37") .......................................................................TNM4CD0819FB
•Power Board (32") . ...................................................................TNM4CD0821F
•Power Board (32"/37") ..............................................................TNM4CD0822F
•IR Board ....................................................................................TNM4CD0906F
•RS232 Board ............................................................................TNM4CD0820F
•SW+AV3 Board (37") .................................................................TNM4CD0807F
•Key Board (32") . .......................................................................TNM4CD0809F
•AV3 Board (32") ........................................................................TNM4CD0810F
•SPEAKERS . .............................................................................TTX4CM008C
Always be sure to ask a qualified technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being
played with by young children, creating the potential risk of suffocation.
When using the LCD Display
Do not bring your hands, face or objects close to the
ventilation holes of the Display.
• Top of the Display is usually very hot due to the high
temperature of exhaust air being released through the
ventilation holes. Burns or personal injuries can happen if
any body parts are brought too close. Placing any object
near the top of the display could also result in heat damages
to the object as well as to the Display if its ventilation holes
are blocked.
Be sure to disconnect all cables before moving the
Display.
•Moving the Display with its cables attached might damage
the cables which, in turn, can cause fire or electric shock.
Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
•Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it from
becoming dusty.
•Built-up dust on the power cord plug can increase
humidity which might damage the insulation and cause
fire. Unplug the cord from the wall outlet and clean it
with a dry cloth.
This Display radiates infrared rays, therefore it may
affect other infrared communication equipment.
Install your infrared sensor in a place away from direct
or reflected light from your Display.
Note:
Image retention may occur. If you display a still picture for
an extended period, the image might remain on the screen.
However, it will disappear after a while.
To Prevent the Display From Falling
Required accessories:
A
Holding Strip (1)
B
Assembly screw (1)
size: 4 mm x 10
C
Wood screw (1)
1. Use the wood screw to attach the holding strip
to the base table (C).
Note:
If the base table has no hole, align with the hole
on the holding strip and dig one on the base
table.
2. Screw the holding strip to the pedestal (B).
Note:
Make sure that the holes on the holding strip are
properly aligned with the pedestal and the base
table to ensure stability and prevent the Display
from falling down.
B
C
A
Safety Precautions / Maintenance
WARNING
Setup
Do not place the Display on sloped or unstable
surfaces.
•The Display may fall off or tip over.
Do not place any objects on top of the Display.
•If water spills onto the Display or foreign objects get
inside it, a short-circuit may occur which could result in
fire or electric shock. If any foreign objects get inside the
Display, please consult an Authorized Service Center.
Do not cover the ventilation holes.
•Doing so may cause the Display to overheat, which can
cause fire or damage to the Display.
Transport only in upright position!
•Transporting the unit with its display panel facing
upright or downward may cause damage to the internal
circuitry.
When using the pedestal, leave a space of 3 15/16” (10
cm) or more at the top, left and right, and 2 3/4” (7 cm)
or more at the rear, and also keep the space between
the bottom of the display and the floor surface. If using
some other setting-up method, follow the manual of it.
(If there is no specific indication of installation dimension
in the installation manual, leave a space of 3 15/16”
(10 cm) or more at the top, bottom, left and right, and 2 3/4”
(7 cm) or more at the rear.)
AC Power Supply Cord
The Display is designed to operate on 110 - 127 V AC,
50/60 Hz.
Do not handle the power cord plug with wet hands.
•Doing so may cause electric shocks.
Do not do anything that might damage the power cable.
When disconnecting the power cable, hold the plug,
not the cable.
•Do not make any modifications, place heavy objects on,
place near hot objects, heat, bend, twist or forcefully
pull the power cable. Doing so may cause damage to
the power cable which can cause fire or electric shock.
If damage to the cable is suspected, have it repaired at
an Authorized Service Center.
If the Display will not be used for a long period of time,
unplug the power cord from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound),
or if smoke or an abnormal odor is detected from the
Display, unplug the power cord immediately.
•Continuous use of the Display under these conditions
might cause fire or permanent damage to the unit.
Have the Display evaluated at an Authorized Service
Center. Services to the Display by any unauthorized
personnel are strongly discouraged due to its high
voltage dangerous nature.
If water or foreign objects get inside the Display, if the
Display is dropped, or if the cabinet becomes damaged,
disconnect the power cord plug immediately.
•A short may occur, which could cause fire. Contact an
Authorized Service Center for any repairs that need to be
made.
Securely insert the power cord plug as far as it will go.
•If the plug is not fully inserted, heat may be generated
which could cause fire. If the plug is damaged or the
wall socket plate is loose, they should not be used.
Maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which
neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface
is dry.
•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become
damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise
the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added
and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
•Do not allow any detergent to come into direct contact with the surface of the Display. If water droplets get inside the
unit, operating problems may result.
•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact
with articles made from rubber or PVC.
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Operating Instruction book
Remote Control Transmitter
TNQ4CM051
POWER
Batteries for the Remote Control
Transmitter (AA Size × 2)
INPUT
MUTE
MENU
RETURN
RECALL ASPECT OFF TIMER
CH
TNQ4CM051
VOL
DISPLAY
HDMI cable
(for TH-32LRT12U,
TH-37LRT12U)
Remote Control Batteries
Requires two AA batteries.
1. Push the hook to release, then open the battery cover.
2. Insert batteries - note the correct polarity ( + and -).
“AA” size
Open
Close
Hook
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precautions:
1.Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2.Do not combine a used battery with a new one.
3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.
6.Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
Accessories
Location
Place the display at a comfortable distance for viewing. Avoid placing it where sunlight or other bright light (including
reflections) will fall on the screen.
Use of some types of fluorescent lighting can reduce remote control transmitter range.
Adequate ventilation is essential to prevent an internal component failure. Keep away from areas of excessive heat or
moisture.
■How to use the pedestal
Adjust the stand to your desired angle.
The stand angle can be rotated 15 ° to the right / left.
(View from above)
15°
15°
LCD panel side
Preparation for Wall-hanging
Before mounting the display on the wall, you must remove the pedestal from the display.
Follow the steps below:
1
2
Disconnect all the cables from the display.
A
Remove the pedestal.
A
Remove the four screws.
B
Pull out the pedestal.
B
Foam mat or thick
soft cloth
A
WARNING
Failure to use a Panasonic bracket or choosing to mount the unit yourself will be done at the risk of the consumer.
Any damage resulting from not having a professional installer mount will void your unit’s warranty.
Always be sure to ask a qualified technician to carry out set-up.
Incorrect fitting may cause equipment to fall, resulting in injury and product damage.
Do not mount this LCD display directly below ceiling lights (such as spotlights, floodlights, or halogen lights) which
typically give off high heat. Doing so may warp or damage plastic cabinet parts.
To prevent foreign objects from entering the Display, place the enclosed sticker label on the lower area of the Display
to cover the holes.
•
•
•
•
Connections
Front side
Lift door to open
AV connection (see page 11)
Back side
AV connection (see page 11)
Component (YPbPr) connection
(see page 11)
PC input terminals connection
(see page 12)
Serial Terminals connection (see page 14)
HDMI connection (see page 13)
Audio out connection (see page 13)
10
Connections
AV connection
Example of input signal source
S VIDEO VCR
S VIDEO
OUT
CAMCORDER
VIDEO
OUT
AUDIO
OUT
L
R
VCR
Back side
Front side
Notes:
• Additional equipment and cables shown are not supplied with this set.
• If S Video and Video devices are both connected, the S Video input signal is the priority source.
Component (YPbPr) connection
Example of input signal source
DVD
Digital TV-SET-TOP-BOX
(DTV-STB)
COMPONENT VIDEO OUT
Y
Y, PB, PR, PB
OUT
PR
L
AUDIO
OUT R
Note:
Additional equipment and cables shown are not supplied with this set.
11
Connections
PC Input Terminals connection
COMPUTER
(Female)
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Audio
(Male)
Stereo plug
Connect a cable which matches
the audio output terminal on the computer.
Notes:
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 79.97 kHz and vertical
scanning frequency of 48 to 75 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
• The display resolution is a maximum of 1,024 × 768 dots when the aspect mode is set to “4:3”, and 1,366 × 768 dots
when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show
fine detail with sufficient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need
to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• Applicable input signals for Mini D-sub 15P (see page 29).
Signal Names for Mini D-sub 15P Connector
5
4
10 9
3
2
8
1
7
6
15 14 13 12 11
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
R (PR/CR)
G (Y)
B (PB/CB)
NC (not connected)
GND (Ground)
6
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
11
NC (not connected)
SDA
HD/SYNC
VD
SCL
2
3
4
Pin Layout for PC Input Terminal
12
5
7
8
9
10
12
13
14
15
Connections
HDMI connection
HDMI cable
HDMI
AV OUT
DVD Player or SET-TOP-BOX
(HDMI compatible machines only)
Note:
1. Additional equipment and HDMI cables shown are not supplied with this set.
2. HDMI Version 1.2.
Audio Out connection
Audio equipment
R
AUDIO
OUT
L
Note:
Additional equipment and cables shown are not supplied with this set.
13
Connections
Serial Terminals connection
The SERIAL terminal is used when the Display is controlled by a computer.
COMPUTER
4
5
RS-232C Straight cable
6
7
2
8
1
9
Pin layout for SERIAL Terminal
(Female)
D-sub 9p
3
(Male)
Notes:
• Use the RS-232C straight cable to connect the computer to
Signal names for D-sub 9P connector
the Display.
• The computer shown is for example purposes only.
Pin No.
Details
• Additional equipment and cables shown are not supplied with
2
RXD
this set.
3
TXD
5
The SERIAL terminal conforms to the RS-232C interface
GND
specification, so that the Display can be controlled by a computer
4 • 6
Non use
which is connected to this terminal.
7 • 8
Non use
The computer will require software which allows the sending
1 • 9
NC
and receiving of control data which satisfies the conditions
These signal names are those of computer specifications.
given below. Use a computer application such as programming
language software. Refer to the documentation for the computer
application for details.
Communication parameters
Communication parameters
Command Parameter
Control details
Signal level
RS-232C compliant
PON
None
Power ON
Synchronization method
Asynchronous
POF
None
Power OFF
Baud rate
9600 bps
AVL
**
Volume 00 - 63
Parity
None
AMT
0
Audio MUTE OFF
Character length
8 bits
1
Audio MUTE ON
Stop bit
1 bit
IMS
None
Input select (toggle)
Flow control
RF INPUT
RF1
AV1 INPUT
AV1
Basic format for control data
AV2
AV2 INPUT
The transmission of control data from the computer starts with
AV3
AV3 INPUT
an STX signal, followed by the command, the parameters, and
YPbPr
YPbPr INPUT
lastly an ETX signal in that order. If there are no parameters,
HDMI1
HDMI1 INPUT
then the parameter signal does not need to be sent.
HDMI2
HDMI2 INPUT
HDMI3
HDMI3 INPUT
STX
C1 C2 C3
:
P1 P2 P3 P4 P5
ETX
PC
PC INPUT
Colon
Parameter(s)
End
Screen mode select (toggle)
DAM
None
(1-5 bytes)
(03h)
16:9
FULL
Start
3-character
JUST
JUST
(02h)
command (3 bytes)
NORM
4:3
Notes
With the power off, this display responds to PON
• If multiple commands are transmitted, be sure to wait
command only.
for the response for the first command to come from this
unit before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an ER401 command back to the computer.
14
Power ON / OFF
Using the Power Switch
1
2
Connect the plug to the Wall Outlet.
Press the Power switch on the
Display to turn the set on: PowerOn
Power Indicator: Green
Remote Control Sensor
When the Display is on, press the
Power switch on the Display to turn
the set off.
Power Indicator: Red (Standby)
Power Indicator
Power Switch
Using the Power Button
POWER
INPUT
MUTE
MENU
POWER
POWER button on the remote control to
Press the
turn the Display on.
Power Indicator: Green
POWER
Press the
button on the remote control to
turn the Display off.
RETURN
Power Indicator: Red
RECALL ASPECT OFF TIMER
TNQ4CM051
CH
VOL
Note:
The Display will still consume power as long as the AC cord is connected to the wall outlet. Unplug the AC cord to cut-off
power.
15
Initial selections
Selecting the input signal
POWER
INPUT
INPUT
Press repeatedly until the desired input source signal is displayed
on the screen.
MUTE
MENU
Input signals will change as follows:
HDMI1
YPbPr
HDMI2
AV3
HDMI3
AV2
PC
AV1
RETURN
RECALL ASPECT OFF TIMER
Note:
Selecting is also possible by pressing the INPUT button on the unit.
(TH-32LRT12U)
TNQ4CM051
CH
VOL
INPUT
(TH-37LRT12U)
Selecting the On-Screen Menu Language
1 Display the menu screen.
2
MENU
POWER
MUTE
MENU
Select “Setup Menu”.
INPUT
1 Select
Main Menu
Picture Menu
Sound Menu
DISPLAY
RECALL ASPECT OFF TIMER
3 Select “Language”.
Setup Menu
Language
Movie Mode
Select
English
On
TNQ4CM051
4 Select your preferred language.
English
Français
Español
Adjust
16
RETURN
2 Action
Setup Menu
CH
VOL
Basic Controls
Main Unit
Power Indicator
The Power Indicator will light.
•Power-OFF.... Indicator not illuminated
•Standby......... Red (The Monitor will still consume power as long as the AC cord is still connected to the wall outlet.)
•Power-ON...... Green
Power On / Off Switch
(TH-32LRT12U)
Remote control sensor
CH
VOL
Lift the door to open
Channel Adjustment
Press to change to the next or
previous channel.
Volume Adjustment
Press "+" to increase volume or press "-"
to reduce volume.
MENU
MENU Screen ON (see page 20)
This button is locked by initial setting.
INPUT
INPUT button (see page 16)
(TH-37LRT12U)
INPUT button
(see page 16)
MENU Screen ON (see page 20)
This button is locked by initial setting.
Volume Adjustment
Press "+" to increase volume or
press "-" to reduce volume.
Channel Adjustment
Press to change to the next or
previous channel.
17
Basic Controls
Remote Control Transmitter
POWER button
The Monitor must first be plugged into
the wall outlet.
Press this button to turn the Monitor on,
from standby mode. Press it again to turn
the Monitor Off to standby mode.
MENU button
Displays the menu screen.
(see page 20)
INPUT button (see page 16)
POWER
INPUT
MUTE
MENU
OK button
Press to make selections.
RETURN button
Press the RETURN button to return
to previous menu screen.
POSITION buttons
RECALL button
Press to display the current input signal
mode.
ASPECT button
Press to adjust the aspect.
This button can be used only in AV
input signal. (see page 19)
RETURN
RECALL ASPECT OFF TIMER
TNQ4CM051
CH
Channel buttons
Press the buttons to adjust the channel.
These buttons are also used for to
adjusting digital channel when a tuner
pack is installed. For more information,
please refer to the tuner pack's
manual.
VOL
OFF TIMER button
The Monitor can be preset to switch
to standby mode after a fixed period.
Each time the button is pressed, the
timer is changed with an interval of
10 minutes.
10
20
30
40
50
OFF
120
60
When the timer is set, the Monitor will
display a notification countdown 3
minutes before it switches to standby
mode.
Volume Adjustment
Press the Volume Up “+” or Down “–”
button to increase or decrease the
sound volume level.
DISPLAY
18
Sound mute On / Off
Press this button to mute the sound.
Press again to reactivate sound.
Sound is also reactivated when
power is turned off or volume level
is changed.
ASPECT Controls
The Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture.
POWER
INPUT
MUTE
MENU
ASPECT
Press repeatedly to change the aspect.
For “AV” signal input:
16:9
JUST
4:3
For “YPbPr”, “HDMI” and “PC” signal input:
The aspect ratio is fixed at 16:9.
RETURN
RECALL ASPECT OFF TIMER
CH
TNQ4CM051
Aspect mode
VOL
Picture
Enlarged screen
Description
The display of the pictures fills the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are
enlarged horizontally, and displayed. This mode is suited to displaying
anamorphic pictures with a 16:9 aspect ratio.
16:9
Pictures with a 4:3 aspect ratio are enlarged horizontally so that the
picture distortion is minimized. The display of the areas around the left
and right edges of the screen is slightly elongated.
JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally so that the
picture distortion is minimized. The left and right edges of the pictures
are cut off. The display of the areas around the left and right edges of
the screen is slightly elongated.
DISPLAY
4:3
Pictures with a 4:3 aspect ratio are displayed with their original aspect
ratio. Side panels are displayed at the left and right edges of the
screen.
Pictures with a 4:3 aspect ratio are displayed with their original aspect
ratio. The left and right edges of the pictures are masked by side
panels.
19
On-Screen Menu Display
Various menus allow you to make settings for the picture, sound, and other functions so that you can enjoy watching Display
best suited for you.
Remote Control
1 Display the menu screen.
MENU
Press the menu button.
Unit
Press the MENU button.
1 Press the CH buttons to select the
menu.
2 Press the MENU button.
2 Select the menu.
Main Menu
1 Select
Picture Menu
Sound Menu
Setup Menu
2 Action
3 Select the item.
Picture Menu
Picture Mode
Standard
Contrast
Brightness
Color
Tint
Sharpness
Select
User
Off
Press the CH < or > buttons to select
the item.
32
32
32
00
12
(Example: Picture Menu)
4 Adjust or select.
Press the VOL + or – buttons.
Contrast
32
Adjust
5 Exit the menu.
20
Press to return to the
previous menu.
Press several times until you exit
the menu.
RETURN
Press the INPUT button several times
until you exit the menu.
On-Screen Menu Display
Overview
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
Main Menu
Picture Menu
Sound Menu
Setup Menu
During “AV”, “YPbPr” and “HDMI”
input signal.
Picture Menu
Picture Mode
Standard
Contrast
Brightness
Color
Tint
Sharpness
Vivid
Off
32
32
32
00
12
During “PC” input signal.
Picture Menu
Standard
Contrast
Brightness
Off
32
32
see page 22
Sound Menu
Sound Mode
Sound AI
Standard
Bass
Treble
Balance
MPX
Dynamic
Off
Off
00
00
00
Stereo
see page 23
During “AV”, “YPbPr” and “HDMI”
input signal.
Setup Menu
Language
Movie Mode
During “PC” input signal.
Setup Menu
English
On
see page 24
Auto
H-Pos
V-Pos
Dot_Clock
Clock_Phase
Language
Movie Mode
Off
00
00
00
32
English
On
see page 25
21
Picture Menu
MENU
1
Press
2
Select Picture Menu.
to display the menu screen.
Press to select the menu to adjust.
Press to enter menu.
3
4
Press to select the menu to adjust.
Press to select the desired setting.
Select to adjust each item.
Notes:
• As you scroll through the settings, the Monitor display
changes synchronously.
• Menu items that cannot be adjusted are grayed out.
Adjustable menu changes depending on signal, input
and menu setting.
Press
RETURN
repeatedly to exit the menu.
Press the
During "AV", "YPbPr", "HDMI" input
signal.
Picture Menu
Picture Mode
Standard
Contrast
Brightness
Color
Tint
Sharpness
User
Off
32
32
32
00
12
Normal
Recommended for normal viewing conditions with
subdued room lighting.
User
Customizes each item according to the user's
preference.
Off
32
32
Standard (Off / On)
Select On to reset all picture to the factory default
settings.
Contrast / Brightness / Color / Tint / Sharpness
Depending on the selected Picture Mode, these items
have preset settings.
To adjust each setting according to the user's preference,
set Picture Mode to User, then press the or
buttons.
Contrast
32
22
buttons to switch between modes.
User
Normal
Vivid
Vivid
Provides enhanced picture contrast and sharpness for
viewing in a well-lit room.
During "PC" input signal.
Picture Menu
Standard
Contrast
Brightness
or
Item
Contrast
Details
Adjusts the white areas.
Brightness
Adjusts the dark areas.
Color
Adjusts the color intensity.
Tint
Adjusts the natural flesh tones.
Sharpness
Adjusts the clarity of outline
detail.
Sound Menu
MENU
1
Press
2
Select Sound Menu.
to display the menu screen.
Press to select the menu to adjust.
Press to enter menu.
3
Select to adjust each item.
4
Press
RETURN
Press to select the menu to adjust.
Press to select the desired setting.
repeatedly to exit the menu.
Press the
Sound Menu
Sound Mode
Sound AI
Standard
Bass
Treble
Balance
MPX
Note: Adjustable only in RF mode
(when a tuner pack is installed)
Music
Normal
00
00
00
Press the or buttons to switch
between modes.
Mono
Stereo
M1
M2
buttons to switch between modes.
Dynamic
Dynamic
Off
Off
Stereo
or
Dynamic
Accentuates sharp sounds.
Music
Stresses the sense of sharp sounds.
Normal
Emits the original sound.
Sound AI (Off / On)
Select On to equalize overall volume levels across all
external inputs.
Standard (Off / On)
Select On to reset Bass, Treble, and Balance settings to
factory defaults.
Press the
or
buttons to adjust settings.
Bass
00
Bass
Adjusts low pitch sounds.
Treble
Adjusts pitch sounds.
Balance
Adjusts the left and right volumes.
23
Setup Menu
MENU
1
Press
2
Select Setup Menu.
to display the menu screen.
Press to select the menu to adjust.
Press to enter menu.
3
Select to adjust each item.
4
Press
RETURN
Press to select the menu to adjust.
Press to select the desired setting.
repeatedly to exit the menu.
During "AV", "YPbPr", and "HDMI" input
signal.
Setup Menu
Language
Movie Mode
English
On
Press the or
languages.
buttons to switch between menu
English
Français
Español
Movie Mode (Off / On)
When On, the display attempts to reproduce a more
natural interpretation of sources such as movie pictures,
which are recorded at 24 frames per second.
If the picture is not stable, turn this setting to Off.
24
Setup Menu
PC Setup
MENU
1
Press
2
Select Setup Menu.
to display the menu screen.
Press to select the Setup menu.
Press to enter menu.
3
Select to adjust each item.
4
Adjust the setting.
5
Press
Press to select the item.
Press to select the item.
RETURN
repeatedly to exit the menu.
During "PC" input signal.
Setup Menu
Auto
H-Pos
V-Pos
Dot_Clock
Clock_Phase
Language
Movie Mode
Off
00
00
00
32
English
On
Notes:
• If the PC is not connected, some items
are unadjustable.
• Unadjustable items are grayed out.
• As you scroll through the settings, the
TV display changes synchronously.
On / Off
Select On to automatically adjust H-Pos, V-Pos,
Dot_Clock, and Clock_Phase.
Press the
or
buttons to adjust settings.
H-Pos
00
H-Pos
Adjust the horizontal position.
V-Pos
Adjust the vertical position.
Dot_Clock
Periodic striped pattern interference (noise) may occur
when a striped pattern is displayed. If this happens, adjust
Dot_Clock to minimize such noise.
Clock_Phase
Eliminate the flickering and distortion.
25
HOTEL MODE Setup
The Hotel Mode is a special function which allows users to configure settings to suit certain locations or applications.
MENU
1
Press
2
Select Setup Menu.
to display the menu screen.
Press to select the Setup menu.
Main Menu
Press to enter menu.
Picture Menu
Sound Menu
Setup Menu
3
Select Movie Mode.
Setup Menu
Language
Movie Mode
Press to select the item.
English
On
MUTE
4
Press and hold
5
Select the item and set desired settings.
for more than 3 seconds.
Setup Menu
Initial Input
Onscreen Display
Initial VOL Level
Maximum VOL Level
Input Lock
Button Lock
Remocon User Level
6
26
Press
RETURN
Press to select the item.
Off
On
Off
Off
Off
Menu
Off
repeatedly to exit the menu.
Press to adjust settings.
HOTEL MODE Setup
Hotel Mode Menu List
Item
Details
Off
RF
AV1
AV2
AV3
YPbPr
Adjusts the input signal when the unit is turned on.
Initial Input
HDMI1
HDMI2
HDMI3
PC
Off: The input signal when the power was last turned off is set.
Note:
This menu is available only when "Input Lock" is "Off".
RF mode is available only when Pal Tuner is connected.
Off: Onscreen information is not displayed.
On: Onscreen information is displayed, such as:
Onscreen Display
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer
On 1: Onscreen information is displayed, except some RS-232C communication information is not
displayed.
Used to set the volume level at power-on.
Off: The volume is set to the same level as when the power was last turned off.
Initial VOL Level
0 to 63: The volume is set to the selected level.
Note:
It is not possible to select an Initial VOL Level setting which is higher than the Maximum VOL Level setting.
Used to set the volume level so that it will not exced the maximum setting.
Off: No restrictions are placed on the volume level.
Maximum VOL Level 0 to 63: The volume is restricted to the selected level.
Note:
It is not possible to select a Maximum VOL Level setting which is lower than the Initial VOL Level setting.
Off
RF
AV1
AV2
AV3
Locks the input switch operation.
Input Lock
YPbPr
HDMI1
HDMI2
HDMI3
PC
Off: Input switch can be used.
Note:
RF mode is available only when Pal Tuner is connected.
Used to restrict the operation of the buttons on the main unit.
Button Lock
Off: All the buttons on main unit can be used.
Menu: Locks the Menu button on the main unit.
On:Locks all the buttons on the main unit except the Power button.
Off
User1
User2
User3
Off: You can use all of the buttons on the remote control.
, , , , buttons on the remote control.
Remocon User Level User1:You can only use
User2:You can only use
button on the remote control.
User3:Locks all the buttons on remote control.
POWER
INPUT
MUTE
VOL
POWER
27
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Checks
Sound
Interference
Noisy Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Normal Picture
No Sound
Volume
(Check whether the mute function has been activated on the remote control.)
No Picture
No Sound
Not plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No Picture
Normal Sound
If a signal with a non-applicable color system format, or frequency is input, only the input
terminal indication is displayed.
No Color
Normal Sound
Color controls set at minimum level. (see page 22)
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where
the image is missing appear when I use the zoom
function.
Check whether the batteries have discharged completely and, if they have not, whether they
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong fluorescent
light.
Check whether the remote control designed specifically for use with the unit is being used.
(The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing
very slight contractions in response to changes in the room temperature. There are no adverse
effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a screen wider
than one in the 16:9 mode, blank areas separate from the images are formed at the top and
bottom of the screen.
This LCD Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input signal.
However, this is not a malfunction.
LCD Display panel
Symptoms
It takes a while for the picture to appear.
The edges of the images flicker.
The brightness on both sides of images in 4:3 mode
changes.
There may be red spots, blue spots, green spots and
black spots on the screen.
Example
Image retention appears
28
Check
The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power
has been turned on, when the input has been switched or when the images for the main picture
and sub picture on the two screens are swapped.
Due to the characteristics of the system used to drive the panel, the edges may appear to flicker
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides
may change depending on the kind of program shown: This is normal and not indicative of
malfunctioning.
This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel
is built with very high precision technology giving you fine picture details. Occasionally, a few
non-active pixels may appear on the screen as fixed points of red, blue, green, or black.
Please note this does not affect the performance of your LCD.
Image retention may occur. If you display a still picture for an extended period, the image
might remain on the screen. However, it will disappear after a while. This is not considered
as malfunction.
Applicable Input Signals
Applicable input signals for Mini D-sub 15P
Signal name
Horizontal frequency
(kHz)
1
640 x 480 @ 60 Hz
31.47
2
640 x 480 @ 72 Hz
37.86
Vertical frequency
(Hz)
59.94
72.81
Dot clock frequency
(MHz)
25.18
31.5
3
640 x 480 @ 75 Hz
37.50
75.00
31.5
4
800 x 600 @ 56 Hz
35.16
56.25
36.0
5
800 x 600 @ 60 Hz
37.88
60.32
40.0
6
800 x 600 @ 72 Hz
48.08
72.19
50.0
7
800 x 600 @ 75 Hz
46.88
75.00
49.5
8
1024 x 768 @ 60 Hz
48.36
60.00
65.0
9
1024 x 768 @ 70 Hz
56.48
70.07
75.0
10
1024 x 768 @ 75 Hz
60.02
75.03
78.75
Note: Signals without the above specifications may not be displayed properly.
29
Specifications
TH-32LRT12U
Power Source
Power Consumption
Power on
Stand-by condition
Aspect Ratio
Screen size
(W x H x Diagonal)
(No.of pixels)
Operating condition
Temperature
Humidity
Applicable Input signals
PC signals
Connection terminals
AV1 - AV3
YPBPR
PC IN
HDMI1 - HDMI3
AUDIO OUT
RS-232C
Dimensions (W × H × D)
Including pedestal
Display Set only
Mass (weight)
Including pedestal
Display Set only
TH-37LRT12U
110 - 127 V AC, 50/60 Hz
155 W
1W
190 W
1W
16:9
27.5" x 15.4" x 31.5"
32.2" x 18.1" x 37.0"
(698 mm x 392 mm x 800 mm)
(819 mm x 460 mm x 940 mm)
1,049,088 (1,366 (W) x 768 (H))
32 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
VGA, SVGA, XGA
Horizontal scanning frequency 31.469 - 60.023
Vertical scanning frequency 56 - 85 Hz
VIDEO IN (RCA PIN JACK x 3)
1.0 Vp-p (75 Ω)
S VIDEO IN (MINI DIN 4PIN x 3) Y:1.0 Vp-p (75 Ω), C: 0.286 Vp-p (75 Ω)
AUDIO IN (RCA PIN JACK x 3)
0.5 Vrms
Y (RCA PIN JACK x 1)
1.0 Vp-p (75 Ω)
PB/PR (RCA PIN JACK x 1)
0.7 Vp-p (75 Ω)
AUDIO IN (RCA PIN JACK x 1)
0.5 Vrms
(HIGH-DENSITY MINI D-SUB 15PIN)Y or G with sync 1.0 Vp-p (75 Ω)
Y or G without sync 0.7 Vp-p (75 Ω)
B/PB/CB:0.7 Vp-p (75 Ω)
R/PR/CR:0.7 Vp-p (75 Ω)
HD/VD:1.0 - 5.0 Vp-p (high impedance)
AUDIO IN (M3 JACK)0.5 Vrms
TYPE A Connector x 3
RCA PIN JACK x 2
0.5 Vrms
RS-232C COMPATIBLE
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)
32.4'' x 23" x 9.3"
(821 mm x 584 mm x 236 mm)
32.4" x 21.3" x 4.2"
(821 mm x 539 mm x 106 mm)
37.4" x 25.6" x 12.1"
(949 mm x 650 mm x 307 mm)
37.4" x 25.6" x 4.1"
(949 mm x 608 mm x 104 mm)
36.4 lbs
30.9 lbs
47.4 lbs
39.7 lbs
Sound
Audio Output
20W [10 W + 10 W] (10 % THD)
Note:
Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
30
Panasonic Professional Flat Panel Display Limited Warranty
(for the U.S.A and Puerto Rico)
Panasonic Professional Display Company
Unit of Panasonic Corporation of
North America
One Panasonic Way 1F-10
Secaucus, NJ 07094
Panasonic Professional Flat Panel Display
Limited Warranty
Panasonic Professional Display Company. (referred to
as “the Warrantor”) will repair this product and all
included accessories with new or refurbished parts,
free of charge in the USA or Puerto Rico, of the
original purchase in the event of a defect in materials or
workmanship as follows:
Models or Parts
Part
Warranty
Professional Flat
Panel Display
2 Years
Labor
Warranty
2 Years
On-site or carry-in service in the USA and Puerto Rico
may be obtained during the warranty period by contacting
Panasonic Professional Display Company Service toll free
at 1-800-973-4390.
This warranty is extended only to the original purchaser
and is non transferable. A purchase receipt or other
proof of date of original purchase will be required before
warranty service is rendered.
This warranty only covers failures due to defects in
materials or workmanship, which occur during normal
use. The warranty does not cover damage which occur
in shipment, or failures which are caused by products
not supplied by the warrantor, or failures which result
from improper installation, set-up adjustments, improper
antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge,
improper voltage supply, lighting damage, or service by
anyone other than an authorized repair facility, or
damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITION, DAMAGE
TO DISCS) RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF
THE WARRANTY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above
exclusions or limitations may nor apply to you. This
warranty gives you specific legal rights and you may
other rights, which vary from state to state.
If you have a problem with this product that is not
handled to your satisfaction, then write the Consumer
Affairs Department at the Company address indicated
above.
In the USA and Puerto Rico
FOR SERVICE
CALL TOLL FREE
1-800-973-4390
31
LIMITED WARRANTY STATEMENT
(for Canada)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
LIMITED WARRANTY STATEMENT
Panasonic Canada Inc. (also known as PCI) warrants this product to be free of
defects in material and workmanship under normal use during the applicable
warranty coverage period described below. PCI agrees to repair, or at its option,
exchange, any part that becomes defective. However, the product must be
purchased and serviced in Canada. The product or part that shows evidence of
defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast
Service Center. This warranty does not cover shipping costs.
The warranty coverage period is one year for both parts and labour beginning with
the date of original end user purchase, subject to the exceptions as stated below.
Repaired or replacement parts supplied during the warranty coverage period carry
the unexpired portion of the original warranty coverage period. Proof of product
purchase is a condition of warranty service. The owner must produce the product
purchase receipt or other satisfactory evidence of date of original purchase.
This warranty does not apply to external appearance items, such as handles, knobs,
safety windows, etc. This warranty does not apply to any part, or parts, of the
product, installed, altered, repaired or misused in any way that, in the opinion of PCI,
affects the reliability of or detracts from the performance of the product.
For products requiring routine preventive maintenance, that maintenance must be
performed in order to maintain warranty coverage.
Serial numbers that have been altered, defaced or removed void this warranty. This
warranty does not cover replacements or repairs necessitated by loss or damage
resulting from any cause beyond the control of PCI.
Marking or retained images (sometimes called “burn-in”) resulting from the display of
fixed images on video display products are not defects and are not covered under
this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or the exclusion of implied warranties, so the
above limitations and exclusions may not be applicable.
32
WARRANTY COVERAGE PERIOD EXCEPTIONS
Item
Video Tape
P2/SD Cards
Video Heads
D5 Video heads
Parts
30 days—Replacement only
(content not covered)
(Content not covered)
1 year or 2,000 hrs. (prorated)
Whichever comes first
1 year or 1,000 hrs.
Whichever comes first
90 days
2 years
Maintenance Items
Colour Camera CCD
Imaging Block
BT-H Series LCD Monitors 2 years
3 years or 17,000 hrs.
* DLP™ Projectors
Whichever comes first
3 years or 2,500 hrs.
* LCD Projectors above
Whichever comes first
2,500 ANSI Lumens
3 years or 1,500 hrs.
* LCD Projectors below
Whichever comes first
2,500 ANSI Lumens
50% of the rated lamp life or 1 year.
Projector Lamps
Whichever comes first
103 inch Plasma displays 3 year (burn-in not covered)
1 year plus balance (if any) of
Hard Drive Disk Unit
the original Manufacturer’s
Limited Warranty.
(Content not covered)
Labour
N/A
N/A
1 year or 2,000 hrs.
Whichever comes first
1 year or 1,000 hrs.
Whichever comes first
90 days
1 year
1 year
3 years or 17,000 hrs.
Whichever comes first
3 years or 2,500 hrs.
Whichever comes first.
3 years or 1,500 hrs.
Whichever comes first
50% of the rated lamp life or 1 year.
Whichever comes first.
3 year
1 year
• Dust, smoke, rental/staging environment and twenty-four/seven operation,
dramatically decreases the interval between performances of routine preventive
maintenance required to maintain this warranty coverage.
Warranty Service
If the product needs to be shipped for service, carefully pack (preferably in the
original carton) and enclose a letter, detailing the complaint. Send prepaid and
adequately insured to the local authorized Panasonic Service Centre in your
area or to Panasonic Technical Support and Product Services Department, 5770
Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location
requires a return authorization before shipment. No liability is assumed for loss
or damage to the product while in transit.
Customer Service
33
This product has a fluorescent lamp that contains mercury.
Disposal may be regulated in your community due to environmental
considerations. For disposal or recycling information, please contact your local
authorities, or the Electronic Industries Alliance:
http://www.eiae.org.
Customer’s Record
The model number and serial number of this product can be found on its back cover. You should note this serial number
in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase
to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
 Panasonic Corporation 2009
Panasonic Professional Display Company
Unit of Panasonic Corporation of North America
Executive Office :
One Panasonic Way 1F-10, Secaucus, NJ 07094
EASTERN ZONE : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621
Southeast Region : 1225 Northbrook Parkway, Ste 1-160 Suwanee GA 30024 (770)338-6835
Central Region : 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847)468-5200
WESTERN ZONE : 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region : 6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region : 5870 Stone Ridge, #3, Pleasanton, CA (925) 416-5108
Government Marketing Department : 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
Printed in Taiwan