Impact Drill
original Instructions
Welcome:
Congratulations
you’re now a
BluCaver!
Remember:
Enjoy:
Did you know…
Comply with all safety precautions and
instructions when using your BluCave products.
Need some inspiration or support? The BluCave
website opens-up a whole new world of DIY.
You can ask for help, gain real time product
information, share ideas and receive regular
updates on special BluCave offers.
The Impact Drill can be used with timber, plastic
or metal and the impact setting can be used when
drilling into stone and masonry.
SYMBOL:
You’re one of the growing community who have
embraced the BluCave work zone!
The BluCave Impact Drill is one of the many
convenient AC ToolBods (power tool bodies) that
clicks into your BluCave AC Controller.
•
When in doubt always ask for advice.
•
Always wear protective clothing.
•
Always work in an uncluttered environment.
Tips:
When drilling into...
Timber: Prevent splintering by drilling a pilot hole
approximately 25% of the final hole size.
Metal: Never use the impact drilling setting, use a
nail or punch to mark a start point.
Stone & Masonry: Pierce the work piece using the
drill setting before impact drilling. Remove the drill
at regular intervals to remove debris in the hole.
MODEL NO: TID-600-1
1
2
Getting to know your
BluCave power tool:
ASSEMBLY:
Caution: All assembling, mounting, disassembling and
removing should be done with the Impact Drill turned off. Remove the power cord from the power supply.
Disassembling:
Ensure the Impact Drill is switched off before trying to
remove the Controller.
Press the unlock symbol located on the Controller and
then turn the ToolBod away from the Controller.
Assembly....................................................................... 1
ToolBod and Controller................................................. 1
ToolBod & Controller
AUXILIARY HANDLE
Auxilary Handle............................................................. 2
Drill Bits......................................................................... 3
Operation....................................................................... 4
Switching On/Off...........................................................4
Speed.............................................................................5
Change Rotation Direction........................................... 6
Drilling Depth Stop........................................................ 6
Drill& Impact(Hammer) Drill Mode.................................7
Level...............................................................................7
Storage........................................................................ 8
Cleaning/Servicing....................................................... 8
General Safety Warnings.............................................. 10
Drill Safety Warnings.....................................................15
iMPACt dRILL ToolBod
Controller (sold seperately)
1. Live tool indicator
2. Cord Guard
3. Lock Button
4. Trigger
5. Variable Speed Dial
6. Controller Unlock button
7. Drill Mode Selection
8. Auxiliary Handle
9. Chuck Key
10. Chuck
11. Drill Depth Stop
12. Level
13. Forward/Reverse Switch
10
9
11
12
8
13
Caution: BluCave offer both AC (powered) and DC
(cordless) operated Controllers and ToolBods. AC
ToolBods will only operate with an AC Controller and DC
ToolBods will only operate with a DC Controller.
For simple identification look for the appropriate
colour marking with green representing AC and orange
representing DC.
Assembling:
Align the fixed hook (Grey) of the
Controller into the corresponding
recess on the underside of the
ToolBod. Once located and
engaged, close the two faces
of the Controller and ToolBod
together until they click into
place. (It’s as easy as Hook, Swing
and Click) See Fig. 1.
7
1
6
5
2
4
3
AC Drill TID-600-1 REV 11 EU EN.indd 1
MOUNTing:
Rotate the auxiliary handle anti-clockwise to open the
eye until it fits over the chuck of the drill. Position the
eye over the chuck and onto the drill body. Tighten by
twisting the auxiliary handle clockwise until secure.
See Fig. 2.
removing:
Rotate the auxiliary
handle anti-clockwise
towards the left until the
eye opens enough to
slide off the drill body.
5
The Impact Drill is a variable speed ToolBod. As you
squeeze the trigger on your Controller the speed will
vary from slowest to fastest at maximum depression.
The trigger also has a variable speed dial which may be
pre-selected before switching on. Turn the dial to `A’
for the lowest speed or up to `F’ for the highest speed.
Low speed is ideal for delicate materials when minimum
power and greater control is required.
Medium speed is suitable when a balance of power and
VERSaTILE Carry Cabinets: The BluCave Carry
Cabinets provide storage options for the complete
BluCave range and even your existing tools.
They can be used as full sized portable cases or
mounted on the BluCave Rail as stylish cabinets.
BOOSTERS: You can even ‘boost’ your BluCave to
include power, light and audio.
Visit BluCave.com to view the complete work zone.
3
DRILL BITS
The BluCave Impact Drill Accessory Kit (sold separately)
contains a variety of drill bits that are ideal for most DIY
projects.
INSERTING:
Insert the supplied chuck key into the key hole on the
chuck and turn anti-clockwise to loosen the chuck.
See Fig. 3. Finish opening by rotating the chuck with
your hands. See Fig 4.
Insert the bit and tighten the chuck by hand rotating it
clockwise. Once it is hand-tight place the chuck key
into the key hole on the chuck and turn clockwise to
fasten securely.
Caution: Always ensure the bit is secured before use.
2
1
Plug the power cord into the power supply (and switch it
on if it’s switchable).
The blue power indicator will illuminate on the
Controller once connected to the power supply.
Squeeze the trigger to start the Impact Drill. Keep the
trigger depressed to keep the drill operating. Release
the trigger to stop the drill.
To provide stable speed the power can be locked-on
by pressing the lock button on the Controller when the
trigger is completely depressed. This can be done with
the speed set to any level. Squeeze the trigger fully to
release the lock-on feature then release the trigger to
stop the drill.
Speed
The auxiliary handle can be set in any position for added
stability and control.
Accessories: A set of accessories is available as a
starter kit for each BluCave ToolBod.
Watts
Volts
Amps
Hertz
Alternating Current
Kilograms
Millimetres
No load speed
Revolutions or reciprocations per minute
Decibels (A Weighted)
Vibration
Average vibration
Uncertainty
Double Insulated Construction
4
REMOVING:
Place the supplied chuck key into the key hole and turn
anti-clockwise to loosen the chuck. Finish opening by
rotating the chuck with your hands. Remove the bit.
oPERATION:
Caution: Check that the voltage of your power supply
matches the specified voltage on the ToolBod and on
the Controller. If the voltages of either the Toolbod or
Controller do not match the power supply voltage do not
use the unmatched item/s.
Caution: Always ensure the cord guard is extended and
the tool is not used with it in the `storage’ position. See
AC Controller instructions for details.
aPPLICATIONS
The Impact Drill can be used with timber, plastic, metal
and impact drilling of stone and masonry.
Switching On/Off
6
3
control is needed.
High speed produces fast drilling when accuracy is not
critical.
CHANGE ROTATION DIRECTION
W
V
A
Hz
~
Kg
mm
n0
min-1
dB(A)
m/s²
ah
K
For clockwise rotation move the forward/reverse switch
to the forward position so it is closest to the drill chuck.
For anti-clockwise rotation move the forward/reverse
switch backwards so it is furthest from the drill chuck
See Fig. 5.
5 Caution: Only adjust the
forward/reverse switch when
the motor is stopped.
drilling depth Stop
The desired drilling depth can be set with the
depth stop.
Loosen the auxiliary handle to open the depth stop
locator. Place the depth stop into the locator and set to
the same length as the drill bit.
4
6
7
Use the indicators on the
depth gauge and retract to
the depth you wish the hole
to be. Tighten the auxiliary
handle to fix the depth
gauge in place.
Drill your hole until the depth
stop contacts the surface.
See Fig. 6.
drill & impact (hammer) drill mode
For drilling of timber, metal and plastic; press the
drilling button until flush with the housing.
For impact drilling of masonry; press the impact
(hammer) button until flush with the housing. Ensure
the correct drill bit is fitted before operating. See fig. 7.
7
level:
The Impact Drill is fitted with
a level indicator which should
only be used as a guide.
Ensure the Controller and ToolBod are correctly
assembled and the bit is securely in place before
operating.
Storage:
8
ToolBods come with their own unique storage dock for
compact and protective housing inside the BluCave
Carry Cabinets See Fig. 8
8
Cleaning/Servicing:
Before cleaning the Impact Drill remove the power cord
from the power supply.
The drill and accessories can be wiped over with a damp
cloth but must be completely dry before operating.
Ensure the ventilation slots are kept free from dust.
Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the power tool is maintained.
26/10/2012 9:41:43 AM
Technical Data
Symbols
Impact Drill
MODEL:TID-600-1
Rated Power Input
600W
Chuck Capacity
13mm
No-Load Speed
0-2800RPM
Impact Rate
0-44,800BPM
Right/Left Rotation
Y
Max Drilling Capacity:
Concrete
16mm
Steel
13mm
Wood
25mm
Weight - AC controler not included
1.6Kg
BluCave tools are for private use only and are not suitable
for commercial / professional / continuous use.
Measured values determined according to EN 60745
Typically the A-weighted noise levels of the product are:
90.74 dB(A)
Sound Pressure Level LpA
101.74 dB(A)
Sound Power Level LWA
3 dB(A)
Uncertainty KpA
3 dB(A)
Uncertainty KWA
Wear Hearing Protection!
Vibration total values (triaxial vector sum) determined
according to EN 60745
Drilling into
Vibration emission value ah,D= 5.527 m/s2
Metal
Uncertainty K = 1.5 m/s2
Impact Drilling vibration emission value ah,ID= 10.22 m/s2
into concrete. Uncertainty K = 1.5 m/s2
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
The values given are valid for nominal voltages of 230V.
For lower voltage and models for specific countries
these values can vary.
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value may also be used in
a preliminary assessment of exposure. The vibration
emission during actual use of the power tool can differ
from the declared total value depending on the ways
in which the tool is used. Safety measures to protect
the operator should be identified that are based on an
estimation of exposure in the actual conditions of use
(taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it
is running idle in addition to the trigger time).
The following symbols are important for reading and
understanding the operating instructions. Please take
note of the symbols and their meaning. The correct
interpretation of the symbols will help you to use the
machine in a better and safer manner.
WARNING - To reduce the risk of injury during
operation, always read the instructions.
Always wear hearing protection. The effects of
noise can cause hearing loss.
Always wear safety glasses. When working with
electric power tools, sparks, splinters, chips and dust
particles may be generated and these can cause loss
of sight.
General Power
Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
AC Drill TID-600-1 REV 11 EU EN.indd 2
© Demain International P/L 04/2012
5.Service
a.Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b.(Type Y attachment) If the supply cord is damaged,
it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid
a hazard.
WARNING Read all safety warnings designated by the
symbol and all instructions.
DRILL SAFETY WARNINGS:
• Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
a.Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
b.Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c.Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on
the switch or energising power tools that have the
switch on invites accidents.
d.Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e.Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g.If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
•
•
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
If operation is dusty, also wear a dust mask.
Use appropriate detectors to determine if utility
lines are hidden in the work area or call the local
utility company for assistance. Contact with electric
lines can lead to fire and electric shock. Damaging
a gas line can lead to explosion. Penetrating a
water line causes property damage or may cause an
electric shock.
Switch off the power tool immediately when the tool
insert jams. Be prepared for high reaction torque
that can cause kickback.
—The tool insert jams when:
The power tool is subject to overload OR
It becomes wedged in the workpiece.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure
EC-Declaration of conformity
We, the undersigned Batavia GmbH, Blankenstein 180,
NL-7943PE Meppel, declare by our own responsibility
that the product Impact Drill, Item-No 7060543, Model Nr.
TID-600-1:
Is according to the basic requirements, which are defined
in the European Directives Electromagnetic Compatibility
2004/108/EC (EMC).
Is according to the basic requirements, which are defined
in the European Directives, European Machinery Directive
2006/42/EC.
For the evaluation of conformity, the following
harmonized standards were consulted:
EN 60745-1: 2009+A11, EN 60745-2-1: 2010,
EN 55014-1:2006/A2:2011,
EN 55014-2:1997/A2:2008,
EN 61000-3-2:2006/A1:2009, EN 61000-3-3:2008
Meppel, 01 September 2011
Meino Seinen, QA Representative
Batavia GmbH, Blankenstein 180,
7943 PE Meppel, Netherlands
Distributed by:
Batavia GmbH
Blankenstein 180
7943 PE Meppel - Netherlands
Office phone: +31 (0) 522 820200
www.batavia.eu
10 13 16
1.Work area safety
a.Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b.Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c.Keep children and bystanders away while operating
2.Electrical safety
BLUCAVE.COM
3.Personal safety
g.Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
9 12 15
Always wear a dust mask. When working with wood
and other materials, harmful dust may be generated.
Work with asbestos containing materials is not
permitted!
a power tool. Distractions can cause you to lose
control.
TID-600-1-EU-EN REV 11
e.When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
a.Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b.Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c.Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d.Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
4.Power tool use and care
a.Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was designed.
b.Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c.Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d.Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e.Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
11 14
•
•
•
than by hand.
• Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can
burn or explode.
• Always wait until the machine has come to a
complete stop before placing it down. The tool insert
can jam and lead to loss of control over the power
tool.
• Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
• Keep children and visitors away. Visitors should
wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or
extension cord.
WARRANTY:
This Batavia product comes with a 2 year warranty.
Dear Client, all Batavia products have undergone a strict
quality process. If for any reason this product is not
working or damaged, please contact our Client Service
Centre. Please retain your original receipt of purchase.
The Batavia warranty covers all defects in workmanship
or materials for a two year period from the date of
purchase. The Batavia warranty does not cover any
malfunction, or defect resulting from misuse, neglect,
alteration, or repair.
Deutschland | Kundenservice
Montag bis Freitag von 9 bis 17 Uhr
01805 937832*
Other European countries | Customer Services
Monday till Friday from 8 am until 4 pm
00800 66477400
Website: www.batavia.eu | Email: service@batavia.eu
*Nur €0,14 /Minute aus dem dt. Festnetz,
max. €0,42/Minute aus den Mobilfunknetzen.
26/10/2012 9:41:44 AM