safety and operating manual

SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS
HIGH FREQUENCY MULTI-FUNCTION TOOL
WU681
1
3
2
9
4
5
6
8
7
A
B
A
1
B
A
1
B
2
C
3
2
3
3
2
1
2
1
2
1
1
2
D
C
D
C
D
E1
E2
E1
E2
E1
E2
E3
E4
E3
E4
E3
E4
E3
E4
E3
E4
E5
E5
E5
F
G
F
G
F
ON
ON
ON
OFF
OFF
OFF
G
COMPONENT LIST
1. 2. 3. 4. 5. 6. 7. 8. 9. Hyperlock™ Accessory Clamping Lever
On/Off Switch
Variable Speed Dial
Constant Speed Electronics
Venting Slots
Universal-Fit Accessory Interface*
Smaller Flange (For other brands’ sanding pads)
Flange
Led Light
*Works with other oscillating tool brands’ accessories.
The following compatible brands are trademarks owned by third parties which may be registered by
their respective owners: Black & Decker®, Bosch®, Chicago Electric®, Craftsman®, Dremel®, Fein®,
Genesis®, Makita®, Mastercraft®, Milwaukee®, Performax®, Porter Cable®, Ridgid®, Ryobi®, Skil®, and
Tool Shop®.
TECHNICAL DATA
Type WU681 (6-designation of machinery, representative of high frequency oscillation tool)
Rated voltage
230-240V~50Hz
Rated power
450W
Oscillations speed
11000-20000/min
Protection class
/ll
Tool weight (without power cable)
1.5kg
NOISE INFORMATION
A weighted sound pressure
LpA: 87dB(A)
A weighted sound power
LwA: 98dB(A)
KPA& KWA3.0dB(A)
Wear ear protection when sound pressure is over:
80dB(A)
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined according to EN 60745:
Typical weighted vibration
Vibration emission value ah=3.38m/s2
Uncertainty K = 1.5m/s²
- The declared vibration total value has been measured in accordance with a standard test method and
may be used for comparing one tool with another;
- The declared vibration total value may also be used in a preliminary assessment of exposure.
Warning: The vibration emission value during actual use of the power tool can differ from the
declared value depending on the ways in which the tool is used dependant on the following examples
and other variations on how the tool is used:
How the tool is used and the materials being cut or sanded.
6
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
Warning: To be accurate, an estimation of exposure level in the actual conditions of use should also
take account of all parts of the operating cycle such as the times when the tool is switched off and
when it is running idle but not actually doing the job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 10°C or less
Plan your work schedule to spread any high vibration tool use across a number of days.
7
GENERAL POWER TOOL
SAFETY WARNINGS
Warning: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
1. WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body
is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current
8
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
SAFETY INSTRUCTION FOR
CUTTING
1. Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
2. Always wear a dust mask.
SYMBOLS
WARNING–To reduce the risk of
injury, user must read instruction
manual
Double insulation
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Before working with your tool make
sure that no power cords will be
damaged.
Avoid danger of injury from the
sharp edges of the accessories.
Accessories can become very hot
while working, presenting danger of
burns!
Make sure the tool is unplugged
prior to changing accessories.
Wear protective gloves.
High oscillation frequency
Low oscillation frequency
9
OPERATING INSTRUCTIONS
Note: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The power tool is intended for sawing and
remodelling wooden materials, plastic, plaster,
non-ferrous metals and fasteners (e.g. nails
and clamps) as well as for working on soft wall
tiles and for dry grinding of small surfaces. It is
especially suitable for working close to edges and
for flush cutting.
ASSEMBLY AND OPERATION
Action
Figure
Mounting Accessories
See Fig. A-C
Mounting The Sanding
Sheet
See Fig. D
Mounting The Suction
Device
See Fig. E1-E5
Operating The On/Off
Switch
See Fig. F
Using The Variable Speed
Dial
See Fig. G
The Variable Speed Dial can be used to set the
optimum oscillating frequency according to the
accessories used and the respective application.
Oscillation frequency
Application
High oscillation frequency
Sanding,
sawing, rasping
and polishing
stone and metal.
Low oscillation frequency
Scraping,
polishing
varnishes.
10
APPLICATION
Warning: The sawing teeth are very sharp. Do not touch during mounting and application.
The workpiece must be clamped tightly before it is cut.
Pic
Sawing
Description
Application
Bi-Metal
Metal/Wood End Cut
Blade
Wood, plastic, fiberglass,
nails, non-ferrous metals,
thin sheet metal, hardened
fillers.
Standard Wood End
Cut Blade
Wood, plastic, drywall.
Precision Wood Cut
Blade
Wood, soft plastics.
HSS Semicircle Saw
Blade
Thin wood, plastic,
fiberglass,
non-ferrous metals, thin
sheet metal, hardened fillers,
window glazing.
Sanding Pad
(Perforated)
Wood, plastic, hardened
fillers.
Sanding Finger Pad
Wood, plastic, hardened
fillers.
Triangular Carbide Grit
Rasp
Wood, hardened adhesives,
thin set, masonry.
Carbide Rasp (Finger
Shaped)
Wood, hardened adhesives,
thin set, masonry.
Carbide Grit Semicircle
Saw Blade
Grout, porous concrete,
masonry.
Diamond-Coated
Semicircle Saw Blade
Ceramic and stone tile,
backerboard.
Rigid Scraper Blade
Old paint, hardened
adhesives, caulk, carpet.
Flexible Scraper Blade
Elastic sealants, paint,
adhesive residues, carpet.
Sanding
Rasping
Removing
grout
Scraping
We recommend that you purchase your accessories listed in the above list from the same store that
sold you the tool. Use good quality accessories marked with a well-known brand name. Refer to the
accessory packaging for further details. Store personnel can assist you and offer advice.
NOTE: When plunging and sawing use a slight pendulum motion, to allow sufficient chip removal.
The saw blade lasts longer if the wear is distributed evenly. To ensure an even distribution, loosen the
saw blade, rotate it and retighten firmly.
11
Cut/Sand with a constant movement and light
pressure.
Heavy pressure does not increase the cut/
removal rate – the accessory merely wears faster.
WORKING HINTS FOR YOUR
TOOL
If your power tool becomes too hot, especially
when used at low speed, set the speed to
maximum and run it with no load for 2-3 minutes
to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
Always ensure the workpiece is firmly held or
clamped to prevent movement.
Any movement of the material may affect the
quality of the cutting or sanding finish.
Start your tool before working and turn it off only
after you stop working.
Do not start sanding without having the
sandpaper fitted.
Do not allow the sandpaper to wear away , it will
damage the sanding pad. The guarantee does not
cover sanding pad wear and tear.
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for
finishing surfaces. If necessary, first make a test
run on scrap material.
Excessive force will reduce the working
efficiency and cause motor overload. Replacing
the accessory regularly will maintain optimum
working efficiency.
MAINTAIN TOOLS WITH
CARE
Remove the plug from the socket before
carrying out any adjustment, servicing or
maintenance.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable
parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe
clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free of
dust. Occasionally you may see sparks through
the ventilation slots. This is normal and will not
damage your power tool.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
12
ENVIRONMENTAL
PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice.
PLUG REPLACEMENT
( UK & IRELAND ONLY )
DECLARATION OF
CONFORMITY
If you need to replace the fitted plug then follow
the instructions below.
IMPORTANT
The wires in the mains lead are colored in
accordance with the following code:
BLUE =NEUTRAL
Brown = Live
As the colors of the wires in the mains lead
of this appliance may not correspond with the
colored markings identifying the terminals in
your plug, proceed as follows. The wire which is
colored blue must be connected to the terminal
which is marked with N. The wire which is colored
brown must be connected to the terminal which
is marked with L.
WARNING! Never connect live or neutral wires
to the earth terminal of the plug. Only fit an
approved 13ABS1363/A plug and the correct rated
fuse.
NOTE: If a moulded plug is fitted and has to
be removed take great care in disposing of the
plug and severed cable, it must be destroyed to
prevent engaging into a socket.
We,
Positec Power Tools (Europe) Ltd, PO Box 152,
Leeds, LS10 9DS, UK
13 Amp fuse approved
to BS1362
Connect
Blue to N
(neutral)
Outer sleeve
firmly clamped
Brown L (live)
Cable grip
Declare that the product,
Description WORX High Frequency
Multi-Function Tool
Type WU681 (6-designation of machinery,
representative of high frequency oscillation
tool)
Function Sanding, sawing, rasping, scraping,
polishing
Complies with the following Directives,
2006/42/EC
2004/108/EC
2011/65/EU
Standards conform to:
EN 60745-1
EN 60745-2-4
EN 55014-1
EN 55014-2
EN 61000-3-2
EN 61000-3-3
The person authorized to compile the technical
file,
Name: Russell Nicholson
Address: Positec Power Tools (Europe) Ltd, PO
Box 152, Leeds, LS10 9DS, UK
2014/11/05
Yujin Tang
POSITEC Quality Manager
13
www.worx.com
Copyright © 2014, Positec. All Rights Reserved.
2PGA90APK11004A0
Download PDF
Similar pages
Bosch 1600A00152
Ryobi RMT1801M
SAFETY AND OPERATING MANUAL
100mm belt sander
Worx WX680 Technical data
Makita 9920 power sander
Ryobi EBS800V power sander
Document 1
Bosch 1600A0014W
Oscillating Tool WX680