™
The Aire Deluxe
Ceiling Fans
FP6244**
Net Weight: 14.68 lbs (6.66 kgs)
FP6245**
Net Weight: 16.67 lbs (7.56 kgs)
Model Nos. FP6244** | FP6245**
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1.
2.
3.
4.
5.
Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device,
such as a tag, to the service panel.
Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan
before servicing.
Do not insert anything into the fan blades while the fan is operating.
Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions
1.
2.
To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. See page 4 of owner’s manual for support
requirements. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
knowledge or experience, have your fan installed by licensed electrician.
6. Use only with light kits marked suitable for use in damp locations.
W$51,1* This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
W$51,1* To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
W$51,1* To Reduce The Risk Of Fire Or Electric Shock. Do Not Use This Fan With Any Solid-State Speed Control Device.
W$51,1* To Reduce The Risk Of Electric Shock. Disconnect The Electrical Supply Circuit To The Fan Before Installing Light Kit.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
1.
LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during
the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to defects
in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser will
be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we will
repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding, tarnishing,
or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of heat
or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan
or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must accompany
authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid damage
in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation
will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,
except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that
vary from state to state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
Table of Contents
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
(QHUJ\(I¿FLHQW8VHRI&HLOLQJ)DQV . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
(OHFWULFDODQG6WUXFWXUDO5HTXLUHPHQWV . . . . . . . . . . . . . . . . . . . . . . . . . .4
How to $VVHPEOH YRXU&HLOLQJ)DQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
How to Hang YRXU&HLOLQJ)DQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Wire <RXU&HLOLQJ)DQ . . . . . . . . . . 9
+RZWR,QVWDOO<RXU&DQRS\+RXVLQJ . . . . . . . . . . . . . . . . . .10
How to
+RZWR$VVHPEOH<RXU&HLOLQJ)DQ%ODGHV
. . . . . . . . . . . . . . . . . . . 10
+RZWR$VVHPEOH<RXU6ZLWFK&XS$VVHPEO\/LJKW.LW$VVHPEO\.11
+RZWR2SHUDWH<RXU&HLOLQJ)DQ . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TURXEOH6KRRWLQJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +RZWR&OHDQ<RXU&HLOLQJ)DQ%ODGHV . . . . . . . . . . . . . . . . . . . . . . . . . Parts List—)3 . . . . . . . . . . . . . 16
([SORGHG9LHZ,OOXVWUDWLRQ—)3 17
Parts List—)3 . . . . . . . . . . . . . 18
([SORGHG9LHZ,OOXVWUDWLRQ—)3 19
This manual is designed to make it as easy as possible for you to assemble,
install, operate and maintain your ceiling fan
Materials
Tools Needed for Assembly
• ne hillips head screwdriver
• One stepladder
• hree wire connectors supplied
!
• One wire stripper
lade
• One
screwdriver
iring outlet o and o connectors ust e of type
re uired y the local code he ini u wire would e a
conductor
wire with ground of the following si e:
nstalled ire ength
p to
ft
ft
WARNING
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 9). If you
feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
ire i e
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are
missing contact your local retailer.
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in finding your place should you be interrupted.
WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
• Fan Motor Assembly
• Downrod/Hanger Ball
Assembly
• Hanger Bracket Assembly
• Ceiling Canopy
• Canopy Screw Cover Assembly
• Motor Coupling Cover Assembly
• Switch Cup Assembly (FP6244**)
• Light Kit Assembly (FP6245**)
• Glass (FP6245**)
• Bulbs (FP6245**)
• Blade Holder Set
• Blade Set
ardware ags:
– 1/4˝-20 pan head screws
with lock washers
(blade holder to fan motor hub)
– 3/16˝-24 washer head screws
(blade to blade holder)
– Fiber Washer
– our ire Connectors
– alance it
– Light Kit Chain Coupler (FP6245**)
– Fan Chain Coupler
(FP6244** & FP6245**)
– 10˝ Pull Chain with Chain Coupler
(FP6245**)
NOTE: If you are uncertain of part description, refer to
exploded view illustration.
Hanger Bracket
Assembly
Switch Cup Assembly
(FP6244**)
Motor Coupling
Cover Assembly
Bulbs (FP6245**)
Downrod/
Hanger Ball Assembly
Blade Holder Set
Fan Motor Assembly
Light Kit Assembly
(FP6245**)
Ceiling Canopy
Canopy Screw
Cover Assembly
Glass (FP6245**)
Blade Set
3
Hardware Bags
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the ceiling
fan. Here are a few tips to ensure efficient product
performance.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counterclockwise direction. The airflow produced by the ceiling
fan creates a wind-chill effect, making you “feel” cooler.
Select a fan speed that provides a comfortable breeze,
lower speeds consume less energy.
Winter Season: Reverse the motor and operate the ceiling
fan at low speed in the clockwise direction. This produces
a gentle updraft, which forces warm air near the ceiling
down into the occupied space.Remember to adjust your
thermostat when using your ceiling fan - additional energy
and dollar savings could be realized with this simple step!
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle
of the room and at least 7 feet above the floor and 18
inches from the walls. If ceiling height allows, install the fan
8 - 9 feet above the floor for optimal airflow. Consult your
Fanimation Retailer for optional mounting accessories.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.
Electrical code requires use of a fan-rated outlet box to
support the extra weight and motion associated with a
ceiling fan. A fan-rated box will be labeled as such and
typically supports up to a 70lb ceiling fan. Fan-Rated
Outlet Boxes vary in ratings and design. Ensure the
ratings of your ceiling fan outlet box meet the
requirements for the ceiling fan being installed. Figure 1,
Figure 2 and Figure 3 depicts different structural
configurations that may be used for mounting the
outlet box.
CEILING JOIST
2" x 4"
CEILING
Low-profile use (Figure 1)
A 1 2-in.-deep pancake box is meant to be screwed to a
joist or block. It’s used if only one cable is coming into
the box. It is also available in a saddle-mount
configuration.
OUTLET BOX
Figure 1
Deep-profile use (Figure 2)
A 2-1 -in.-deep box can be attached to blocking
between joists and is roomy enough to handle more
than one cable.
CEILING JOIST
2" x 4"
CEILING
4
Figure 2
OUTLET BOX
Electrical and Structural Requirements (Continued)
Brace use (Figure 3)
Paired with a deep box, this hanger is meant to span
between two joists and takes the place of wooden
blocking.
CEILING JOIST
WARNING
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
acceptable for fan support of 15.88 kg (35 lbs) or less.
Use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to
be replaced. Consult a qualified electrician if
in doubt.
CEILING
OUTLET BOX
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and
remove the existing light fixture.
Figure 3
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
5
How to Assemble Your Ceiling Fan
1. Remove the hanger ball portion from the downrod/
hanger ball assembly by loosening the set screw in the
hanger ball until the ball falls freely down the downrod.
Remove the pin from the downrod, then remove the
hanger ball. Retain the pin and hanger ball for reinstallation in Step 6. (Figure 1)
Pin
Downrod
Set Screw
Hanger Ball
Figure 1
2. Remove the hairpin clip and clevis pin from the
bottom of the downrod. Retain the pin and clip for
reinstallation in Step 4. (Figure 2)
Hairpin
Clip
Clevis Pin
Figure 2
3. Loosen the two set screws in the downrod support
of the motor assembly. Route the black, white and
blue wires through the downrod. (Figure 3)
Black, White and
Blue wires
Downrod
Set Screws (2)
Figure 3
4. Slide downrod into the downrod support on top of
the motor. Install the clevis pin by aligning the holes
in the downrod support with holes in the downrod.
Secure clevis pin with hairpin clip. Tighten the two set
screws with nuts in the downrod support. (Figure 4)
Downrod
Hairpin Clip
Set Screws and
Locking Nuts (2)
WARNING
It is critical that the clevis pin in the downrod support
is properly installed and the set screws and nuts are
securely tightened. Failure to do so could result in
the fan falling.
Clevis Pin
Figure 4
5. Route wires through Motor Coupling Cover, Canopy
Screw Cover and Ceiling Canopy. (Figure 5)
Ceiling Canopy
Canopy Screw
Cover
Motor Coupling
Cover
Figure 5
6
How to Assemble Your Ceiling Fan (continued)
6. Reinstall the hanger ball on the downrod as follows.
Route the black, white and blue wires through the
hanger ball. Position the pin through the two holes in
the downrod and align the hanger ball so the pin is
captured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin. Securely
tighten the set screw in the hanger ball. A loose set
screw could create fan wobble. (Figure 6)
Figure 6
7. Cut off excess lead wire approximately 6 to 9 inches
above the top of the downrod. Strip insulation off
1/2 inch from the end of each lead wire. (Figure 7)
NOTE: All set screws must be checked, and retightened
where necessary, before installation.
Figure 7
7
How to Hang Your Ceiling Fan
WARNING
To avoid possible re or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 1)
MAIN FUSE BOX
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
Figure 1
WARNING
CEILING
The fan must be hung with at least 7’ of clearance
from oor to blades. (Figure 2)
NO LESS
THAN
7 FEET
FLOOR
Figure 2
1. Securely attach the hanger bracket to the outlet box
(not included) using the outlet box screws and washers
supplied with the outlet box. (Figure 3)
WARNING
Outlet Box
Hanger
Bracket
The outlet box must be securely anchored. Hanger
bracket must seat firmly against outlet box. If the
outlet box is recessed, remove wall board until bracket
contacts box. If bracket and /or outlet box are not
securely attached, the fan could wobble or fall.
Flat Washer
Screw (2)
Supplied with
Outlet Box
2. Carefully lift the fan and seat the downrod/hanger ball
assembly on the hanger bracket that was just attached
to the outlet box. Be sure the groove in the ball is lined
up with tab on the hanger bracket. (Figure 4)
WARNING
Tab
Figure 3
Outlet Box
Hanger
Bracket
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
Downrod/Hanger
Ball Assembly
Figure 4
8
How to Wire Your Ceiling Fan
WARNING
To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 1)
MAIN FUSE BOX
Figure 1
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the supply grounding conductor (this may be
a bare wire or wire with green colored insulation).
Securely connect wires with wire connectors supplied.
(Figure 2)
BLACK FAN
WIRE
BLACK
LISTED
OUTLET BOX
GREEN WIRE
(GROUND)
HOUSEHOLD
SUPPLY
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
WHITE
BLUE
2. Securely connect the white fan motor wire to the
white supply (neutral) wire using wire connector
supplied. Securely connect the black fan motor wire
and blue wire to the black supply wire using wire
connector supplied. (Figure 2)
GREEN WIRE
(GROUND) FROM
HANGER BALL
Figure 2
HARDWARE USED:
3. After splicing and making the wire connections, the
wires should be spread apart and turned upward with
the grounded conductor and the equipment-grounding
conductor on one side of the outlet box and the
ungrounded conductor on the other side of the outlet
box. (Figure 3)
WIRE
CONNECTORS
Green Wire
(Ground) from
Supply
White Wire
from Supply
White Wire
from Fan
Green Wire
(Ground) from
Hanger Bracket
WARNING
Green Wire
(Ground) from
Hanger Ball
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until the blades are in place. Noise and fan damage
could result.
3
Listed
Outlet Box
Household
Supply
Black Wire
from Supply
Blue Wire
from Fan
Black Wire
from Fan
Figure 3
9
X
How to Install Your Canopy Housing
NOTE: This step is applicable after the neccessary wiring is completed.
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed. (Figure 1)
Ceiling Canopy
WARNING
Figure 1
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and the
ceiling.
2. Securely attach and tighten the canopy screw cover
over the shoulder screws in the hanger bracket utilizing
the keyslot twist-lock feature. (Figure 2)
Canopy Screw
Cover
Figure 2
How to Assemble Your Ceiling Fan Blades
1. Remove and discard the five rubber motor stops
from the motor assembly by removing the screws.
(Figure 1)
Figure 1
2. Position the blade over the blade holder with
threaded posts showing. Make sure the bottom edge
of the blade is fully seated against the blade holder.
With a phillips screwdriver, tighten 3/16˝-24 washer
head screws and fiber washers to secure the blade
to the blade holder. (Figure 2)
Blade Holder
3/16˝-24
Washer Head Screws
and Fiber Washer
(3 each per blade)
CAUTION
Blade
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.
Figure 2
HARDWARE USED:
10
3/16˝-24
WASHER HEAD
SCREWS
x 15
FIBER WASHER
x 15
How to Assemble Your Ceiling Fan Blades (Continued)
3. Secure the blade holders to the bottom of the motor
assembly using the 1/4˝-20 screws. (Figure 3)
NOTE: Periodically check blade holder hardware and
resecure if necessary.
!
WARNING
Blade Holder
To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between the rotating blades.
Screws
(2 per assembly)
Figure 3
CAUTION
HARDWARE USED:
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
x 10
SCREWS
How to Assemble Your Switch Cup Assembly/Light Kit Assembly
1A—FP6244**. Remove the three screws in the switch
cup assembly. Retain the screws for Step 4. (Figure 1A)
FP6244**
FP6245**
1B—FP6245**. Remove the three screws in light kit
assembly. Retain the screws for Step 4. (Figure 1B)
Light Kit
Assembly
Switch Cup Assembly
Figure 1A
Figure 1B
2. Remove one of the three screws in the support
bracket. Slightly loosen the remaining two screws.
Assemble the adapter-switch housing to the housing
support bracket using the two key slots in the adaper
switch housing. Replace the third screw and securely
tighten all three screws. (Figure 2)
Adapter Switch Housing
Figure 2
3A—FP6244**. Securely attach the 9-pin connector from
the motor assembly to the wire harness socket within the
switch cup assembly. (Figure 3A)
3B—FP6245**. Securely attach the 9-pin connector from
the motor assembly to the wire harness socket within the
light kit assembly. (Figure 3B)
FP6244**
Motor
Assembly
Motor
Assembly
Switch Cup Assembly
Figure 3A
11
FP6245**
Light Kit Assembly
Figure 3B
How to Assemble Your Switch Cup Assembly/Light Kit Assembly (Continued)
4A—FP6244**. Assemble the switch cup assembly to
the switch housing adapter using the previously removed
screws and securely tighten all screws. (Figure 4A)
FP6244**
FP6245**
4B—FP6245**. Assemble the light kit assembly to the
switch housing adapter using the previously removed
screws and securely tighten all screws. (Figure 4B)
Light Kit
Assembly
NOTE: If you have installed your fan without light kit (FP6244**)
skip Steps 5 and 6.
Switch Cup
Assembly
Figure 4A
Figure 4B
5. Insert light bulbs into sockets. (Figure 5)
CAUTION
To reduce the risk of electric shock, disconnect
the electrical supply circuit to the fan before
installing light kit.
Light Kit
Assembly
Bulb
Figure 5
6. Disassemble the finial, trim cover and nut in light kit
assembly. Securely attach the glass to light kit assembly
using supplied nut, trim cover and finial. Do not over
tighten. (Figure 6)
Glass
Light Kit Assembly
Nut
Trim Cover
Finial
Figure 6
12
How to Operate Your Ceiling Fan
1. Restore electrical power to the outlet box by
turning the electricity on at the main fuse box.
(Figure 1)
MAIN FUSE BOX
Figure 1
2A. Install the fan pull chain coupler. (Figure 2A)
FP6244**
FP6245**
2B. Install the fan pull chain coupler and light kit pull
chain coupler. (Figure 2B)
Light Kit Pull
Chain Coupler
Fan Pull Chain Coupler
3. Check the operation of the fan by gently pulling on
the fan pull chain. (Figure 3)
Fan Pull
Chain
Coupler
Figure 2A
Figure 2B
FP6244**
FP6245**
Fan Pull Chain Operating Sequence
1st Pull
nd
2 Pull
3rd Pull
th
4 Pull
High
Medium
Low
Off
Figure 3
4. « FP6245** ONLY »
Check the operation of the light by gently pulling on
the light pull chain. (Figure 4)
Light Pull Chain Operating Sequence
1st Pull
nd
2 Pull
On
Off
Figure 4
5. If airflow is desired in the opposite direction, turn the
fan off and wait for the blades to stop turning. Then
slide the reverse switch to the opposite position and
turn fan on again. (Figure 5)
FP6244**
FP6245**
Reversing
Switch
Reverse Switch Information
Season
Summer
Winter
Rotation Direction
Counter-Clockwise
Clockwise
Switch Position
Left
Right
Reversing
Switch
Figure 5
13
Trouble Shooting
WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Trouble
Probable Cause
1. Fuse or circuit breaker blown.
1.FAN WILL
NOT START
2. Loose power line connections to the
fan, or loose switch wire connections
in the switch housing.
1. Blades not attached to fan.
2. Loose screws in motor housing.
3. Screws securing fan blade holders to
motor flywheel are loose.
2.FAN SOUNDS NOISY
3.FAN WOBBLES
EXCESSIVELY
4. Wire connectors inside housing
rattling.
Suggested Remedy
1. Check main and branch circuit fuses
or circuit breakers.
2. Check line wire connections to fan
and switch wire connections in the
switch housings.
CAUTION: Make sure main power is
turned off !
1. Attach blades to fan before operating.
2. Check to make sure all screws in
motor housing are snug (not overtight).
3. Check to make sure the screws which
attach the fan blade holders to the
motor flywheel are tight.
4. Check to make sure wire connectors
in switch housing are not rattling
against each other or against the
interior wall of the switch housing.
CAUTION: Make sure main power is
turned off !
5. Screws holding blades to blade
holders are loose.
5. Tighten screws securely.
6. Lower housing support set screw
loose.
6. Tighten set screw securely.
1. Setscrew in downrod support is loose.
1. Tighten both setscrews securely in
downrod support.
2. Tighten the setscrew in the downrod/
hanger ball assembly.
3. Check to be sure screws which attach
the fan blade holders to the flywheel
are tight.
2. Setscrew in downrod/hanger ball
assembly is loose.
3. Screws securing fan blade holders to
flywheel are loose.
4. Blade holders not seated properly.
5. Hanger bracket and/or ceiling outlet
box is not securely fastened.
6. Fan blades out of balance.
4. Check to be sure the fan blade
holders seat firmly and uniformly to
the surface of the motor housing.
If holders are seated incorrectly,
loosen the screws and retighten.
5. Tighten the hanger bracket screws to
the outlet box, and secure outlet box.
6. Balance blades using balance kit
provided in hardware bag.
1. If possible, consider using a longer
downrod (not included, you can buy
the longer downrod from
fanimation.com).
4.NOT ENOUGH AIR
MOVEMENT
14
Maintenance
1. Periodic cleaning of your new ceiling fan is the only
maintenance that is needed. When cleaning, use
only a soft brush or lint free cloth to avoid
scratching the finish. Abrasive cleaning agents are
not required and should be avoided to prevent
damage to finish.
CAUTION
Do not use water when cleaning your ceiling fan.
It could damage the motor or the finish and create
the possibility of electrical shock.
How to Clean Your Ceiling Fan Blades
Periodic light dusting of the blades is recommended.
A feather duster will work best.
Avoid using water, cleansers, or harsh rags, which
can warp and ruin the finish.
15
Parts List
Model No. FP6244**
Reference #
Description
Part #
1
2
3
4
5
6
7
8
9
Hanger Bracket Assembly
Hanger Ball/Downrod Assembly
Canopy
Canopy Screw Cover Assembly
Motor Coupling Cover
Fan Motor Assembly
Blade Holder Set
Blade Set
Switch Cup Assembly
APGAC110BL
ADRAC1-45**
PPAC1012**
APPAC1101**
APPAC1411**
AMA6244**
AP624412**
AP624405**
AP624404**
10
—
—
—
Loose Hardware Bag:
Balance Kit
Wire Connectors (4)
Fan Chain Coupler
Blade Mounting Hardware Bag:
Washer Head Screws 3/16˝-24 (16)
Fiber Washer (16)
Blade Holder Mounting Hardware Bag:
Pan Head Screw 1/4˝-20 with Lock Washer (11)
HDWFP6244**
—
—
—
—
—
—
—
—
—
** Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
•
•
•
Part Number
Part Description
Fan Model Number
Contact your retail store for repair parts.
16
Aire Deluxe™
Model FP6244**
Exploded-View Illustration
1
10
2
3
4
5
6
10
8
7
10
9
10
10
Figure 1
NOTE: The illustration shown is not to scale or its actual con guration may vary.
Product/parts are subject to change without notice.
17
Parts List
Model No. FP6245**
Reference #
Description
Part #
1
2
3
4
5
6
7
8
9
10
11
Hanger Bracket Assembly
Hanger Ball/Downrod Assembly
Canopy
Canopy Screw Cover Assembly
Motor Coupling Cover
Fan Motor Assembly
Blade Holder Set
Blade Set
Light Kit Assembly
Glass
Bulbs (3)
APGAC110BL
ADRAC1-45**
PPAC1012**
APPAC1101**
APPAC1411**
AMA6245**
AP624412**
AP624405**
AP624501**
P624501FW
PPGU24C13
12
—
—
—
—
—
Loose Hardware Bag:
Balance Kit
Wire Connectors (4)
Fan Chain Coupler
Light Kit Chain Coupler
10˝ Pull Chain with Chain Coupler
Blade Mounting Hardware Bag:
Washer Head Screws 3/16˝-24 (16)
Fiber Washer (16)
Blade Holder Mounting Hardware Bag:
Pan Head Screw 1/4˝-20 with Lock Washer (11)
HDWFP6245**
—
—
—
—
—
—
—
—
—
—
—
** Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
•
•
•
Part Number
Part Description
Fan Model Number
Contact your retail store for repair parts.
18
Aire Deluxe™
Model FP6245**
Exploded-View Illustration
1
12
2
3
4
5
6
12
12
8
7
11
9
12
10
12
12
Figure 1
NOTE: The illustration shown is not to scale or its actual con guration may vary.
Product/parts are subject to change without notice.
17
Copyright 2015 Fanimation
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free (888) 567-2055
FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website @ www.fanimation.com
2015/11 V.01
Download PDF