HP ProLiant ML150 Generation 3 Server Installation Sheet

HP ProLiant ML150
Generation 3 Server
Rear panel components
Item
Code
Description
20
P20
Front USB 2.0 cable header
21
P10
18-pin front panel I/O connector
• Keyboard
22
SW2
CMOS reset button
• Mouse
23
U32
Intel ICH ESB2 chip
• Monitor
24
P11
Password jumper
• UPS
25
J15
PCI slot 4(64-bit PCI-X)
26
J14
PCI slot 3(64-bit PCI-X)
27
J13
PCI slot 2(64-bit PCI-X)
28
J12
PCI slot 1(32-bit PCI)
29
J38
System BIOS
30
J10
PCI slot 5(PCI-E x8)
a. Power up the server.
31
J11
PCI slot 6(PCI-E x4)
b. Press the Esc key at the HP logo screen.
32
J9
HP LO100c management card slot
33
U4
Broadcom GbE LAN chipset
Configuring the server
1. Connect all peripherals:
Installation Sheet
NOTE: Refer to the HP ProLiant ML150 Generation 3 Server
Support CD. Use the CD for updated information about the server
and as a reference for any additional information not provided in
this installation sheet.
2. Determine the server BIOS version:
c. Note the server BIOS version during the POST boot-up.
d. Verify the server BIOS version against the latest BIOS version listed
for this server on the HP website:
http://www.hp.com
e. If you do not have the latest BIOS, update the BIOS now.
Refer to the HP ProLiant ML150 Generation 3 Server Maintenance
and Service Guide available on the HP website:
http://www.hp.com
Default boot priority
By default, the server searches for boot devices in the following order:
1. CD-ROM drive
1
PS/2 mouse port (green)
9
HP LO100c management card port
34
U22
Intel MCH Blackford VS chip
2
PS/2 keyboard port (purple)
10
Power supply cable socket
35
U14
Server Engines Pilot chip
3
Serial port
11
Kensington lock
36
P1B
VGA Port (blue)
4
VGA port
12
Rear System fan
37
P1A
Serial Port (teal)
5
USB 2.0 port
13
Thumbscrew for access panel
38
J4
Server management control firmware
6
LAN port (RJ-45)
14
Key for front panel
39
P4
4-pin rear system fan header
7
HP LO100c management card
slot cover
15
Side panel lock
8
PCI slot covers
Accessing internal components
System board components
Removing the access panel
2. Removable devices
© Copyright 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United States and other countries.
Part number: 404096-004
November 2006 (Fourth edition)
3. Hard drive
4. Network boot
Identifying server components
Front panel components
Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.
Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.
Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.
Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.
Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.
Item
Code
Description
1
XMM4
DIMM slot 4
2
XMM3
DIMM slot 3
3
XMM2
DIMM slot 2
4
XMM1
DIMM slot 1
5
P6
4-pin power connector
6
CR1
5V aux power indicator
7
P7
24-pin power connector
1
CD-ROM drive
6
Drive activity indicator
8
P8
4-pin CPU0 fan connector
2
CD-ROM drive activity indicator
7
Power indicator
9
XU2
Processor0 socket
3
CD-ROM drive eject button
8
EMI shield
10
XU1
Processor1 socket
4
Front bezel lock
9
USB port
11
P24
8-pin power connector
5
Power button
10
Hard disk drive (HDD) cage
12
P22
4-pin CPU1 fan connector
13
CR2
CPU 1 System Error Indicator
CR3
CPU 2 System Error indicator
14
P25
IDE channel
15
J32
Internal USB 2.0 port
16
P21
4-pin front system fan header
17
P23
External LED connector
18
XBT1
Battery
19
CR4
3.3V aux power indicator
CR5
3.3V power indicator
Removing the front bezel
HP ProLiant ML150
Generation 3 Server
Rear panel components
Item
Code
Description
20
P20
Front USB 2.0 cable header
21
P10
18-pin front panel I/O connector
• Keyboard
22
SW2
CMOS reset button
• Mouse
23
U32
Intel ICH ESB2 chip
• Monitor
24
P11
Password jumper
• UPS
25
J15
PCI slot 4(64-bit PCI-X)
26
J14
PCI slot 3(64-bit PCI-X)
27
J13
PCI slot 2(64-bit PCI-X)
28
J12
PCI slot 1(32-bit PCI)
29
J38
System BIOS
30
J10
PCI slot 5(PCI-E x8)
a. Power up the server.
31
J11
PCI slot 6(PCI-E x4)
b. Press the Esc key at the HP logo screen.
32
J9
HP LO100c management card slot
33
U4
Broadcom GbE LAN chipset
Configuring the server
1. Connect all peripherals:
Installation Sheet
NOTE: Refer to the HP ProLiant ML150 Generation 3 Server
Support CD. Use the CD for updated information about the server
and as a reference for any additional information not provided in
this installation sheet.
2. Determine the server BIOS version:
c. Note the server BIOS version during the POST boot-up.
d. Verify the server BIOS version against the latest BIOS version listed
for this server on the HP website:
http://www.hp.com
e. If you do not have the latest BIOS, update the BIOS now.
Refer to the HP ProLiant ML150 Generation 3 Server Maintenance
and Service Guide available on the HP website:
http://www.hp.com
Default boot priority
By default, the server searches for boot devices in the following order:
1. CD-ROM drive
1
PS/2 mouse port (green)
9
HP LO100c management card port
34
U22
Intel MCH Blackford VS chip
2
PS/2 keyboard port (purple)
10
Power supply cable socket
35
U14
Server Engines Pilot chip
3
Serial port
11
Kensington lock
36
P1B
VGA Port (blue)
4
VGA port
12
Rear System fan
37
P1A
Serial Port (teal)
5
USB 2.0 port
13
Thumbscrew for access panel
38
J4
Server management control firmware
6
LAN port (RJ-45)
14
Key for front panel
39
P4
4-pin rear system fan header
7
HP LO100c management card
slot cover
15
Side panel lock
8
PCI slot covers
Accessing internal components
System board components
Removing the access panel
2. Removable devices
© Copyright 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United States and other countries.
Part number: 404096-004
November 2006 (Fourth edition)
3. Hard drive
4. Network boot
Identifying server components
Front panel components
Printed in the US
404096- 004
Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.
Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.
Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.
Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.
Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.
Item
Code
Description
1
XMM4
DIMM slot 4
2
XMM3
DIMM slot 3
3
XMM2
DIMM slot 2
4
XMM1
DIMM slot 1
5
P6
4-pin power connector
6
CR1
5V aux power indicator
7
P7
24-pin power connector
1
CD-ROM drive
6
Drive activity indicator
8
P8
4-pin CPU0 fan connector
2
CD-ROM drive activity indicator
7
Power indicator
9
XU2
Processor0 socket
3
CD-ROM drive eject button
8
EMI shield
10
XU1
Processor1 socket
4
Front bezel lock
9
USB port
11
P24
8-pin power connector
5
Power button
10
Hard disk drive (HDD) cage
12
P22
4-pin CPU1 fan connector
13
CR2
CPU 1 System Error Indicator
CR3
CPU 2 System Error indicator
14
P25
IDE channel
15
J32
Internal USB 2.0 port
16
P21
4-pin front system fan header
17
P23
External LED connector
18
XBT1
Battery
19
CR4
3.3V aux power indicator
CR5
3.3V power indicator
Removing the front bezel
Installing mass storage devices
Installing the processor
The drive bays on the front panel can accommodate up to six hard drives.
The server supports both SAS and SATA hard drives.
The LGA771 processor socket in the HP ProLiant ML150 Generation 3 server
supports Dual-Core Intel® Xeon® Processor 5000/5100 series and
Quad-Core Intel® Xeon® Processor 5300 series.
CAUTION: Drives can be damaged by static electricity. Before
handling drives, touch an unpainted metal surface to discharge
static electricity.
Hot-Plug SATA and Hot-Plug SAS/SATA HBA model
Installing the memory
The following guidelines must be followed when memory modules are
being added or replaced:
• For 2P system, both physical processors must be of the same type
and speed.
• Use 533/667 MHz ECC FBD (Fully Buffered DIMM).
• Supported DIMM: 512 MB, 1 GB, and 2 GB (Maximum 8 GB system
memory size)
WARNING! Align pin 1 on the processor with pin 1 on the
processor socket, or pin damage will occur.
• Supported configurations: Single DIMM in slot 1, one identical pair in
slot 1 & 3, two pairs (4 DIMMs).
Non-Hot-Plug SATA
CAUTION: DIMMs can be damaged by improper handling.
Always use an anti-static wrist strap and grounding mat, and
discharge static electricity before touching DIMMs.
NOTE: Remove the access panel before the following installation
procedure.
Removing the air baffle
NOTE: Refer to “System Board Components” in this document for
the DIMM locations.
NOTE: Before installing the memory or the processor, remove the
air baffle first.
WARNING! Refer to the label on top of the cooler to make sure
the air flow direction is correct.
WARNING! Be sure that the cooler sits squarely on the processor, or
overheating and damage to the processor may occur.
Getting additional documentation
NOTE: Additional drives pre-assembled in the proper carriers can
be purchased from HP. Please visit the HP website for additional
information.
1. Insert the memory module into the socket.
2. Push both socket latches inward.
Installing the PCI expansion card
1. Slightly pull out the blue snap rivet.
The server supports six PCI bus slots.
2. Move the air baffle to the inside direction of the chassis to unhook the air
baffle from the hooks on the cooler.
• Three PCI-X slots (64-bit)
• Two PCI-Express slots
• One PCI slot (32-bit)
NOTE: Refer to “System Board Components” in this document for
the expansion slot locations.
3. Take the air baffle out from the chassis.
To reinstall the air baffle, reverse the above procedure.
WARNING! The air baffle covers those areas in dotted line of
system board as shown in the below figure. When removing or
installing the air baffle, make sure the location is correct and do
not interfere with any nearby components.
For additional documentation, refer to the HP ProLiant ML150 Generation 3
Server Support CD. You can also access additional information and
documentation from the HP external website, either by connecting directly
or through the Support CD.
Installing mass storage devices
Installing the processor
The drive bays on the front panel can accommodate up to six hard drives.
The server supports both SAS and SATA hard drives.
The LGA771 processor socket in the HP ProLiant ML150 Generation 3 server
supports Dual-Core Intel® Xeon® Processor 5000/5100 series and
Quad-Core Intel® Xeon® Processor 5300 series.
CAUTION: Drives can be damaged by static electricity. Before
handling drives, touch an unpainted metal surface to discharge
static electricity.
Hot-Plug SATA and Hot-Plug SAS/SATA HBA model
Installing the memory
The following guidelines must be followed when memory modules are
being added or replaced:
• For 2P system, both physical processors must be of the same type
and speed.
• Use 533/667 MHz ECC FBD (Fully Buffered DIMM).
• Supported DIMM: 512 MB, 1 GB, and 2 GB (Maximum 8 GB system
memory size)
WARNING! Align pin 1 on the processor with pin 1 on the
processor socket, or pin damage will occur.
• Supported configurations: Single DIMM in slot 1, one identical pair in
slot 1 & 3, two pairs (4 DIMMs).
Non-Hot-Plug SATA
CAUTION: DIMMs can be damaged by improper handling.
Always use an anti-static wrist strap and grounding mat, and
discharge static electricity before touching DIMMs.
NOTE: Remove the access panel before the following installation
procedure.
Removing the air baffle
NOTE: Refer to “System Board Components” in this document for
the DIMM locations.
NOTE: Before installing the memory or the processor, remove the
air baffle first.
WARNING! Refer to the label on top of the cooler to make sure
the air flow direction is correct.
WARNING! Be sure that the cooler sits squarely on the processor, or
overheating and damage to the processor may occur.
Getting additional documentation
NOTE: Additional drives pre-assembled in the proper carriers can
be purchased from HP. Please visit the HP website for additional
information.
1. Insert the memory module into the socket.
2. Push both socket latches inward.
Installing the PCI expansion card
1. Slightly pull out the blue snap rivet.
The server supports six PCI bus slots.
2. Move the air baffle to the inside direction of the chassis to unhook the air
baffle from the hooks on the cooler.
• Three PCI-X slots (64-bit)
• Two PCI-Express slots
• One PCI slot (32-bit)
NOTE: Refer to “System Board Components” in this document for
the expansion slot locations.
3. Take the air baffle out from the chassis.
To reinstall the air baffle, reverse the above procedure.
WARNING! The air baffle covers those areas in dotted line of
system board as shown in the below figure. When removing or
installing the air baffle, make sure the location is correct and do
not interfere with any nearby components.
For additional documentation, refer to the HP ProLiant ML150 Generation 3
Server Support CD. You can also access additional information and
documentation from the HP external website, either by connecting directly
or through the Support CD.