Cabinet Systems
Energy Efficient Data
Center Cabinet and
Containment Systems
For more information about Cisco Compatible Solutions visit
https://marketplace.cisco.com/catalog and search Panduit.
Using the Panduit Energy
Efficient Data Center Cabinet
System, you can greatly
improve the energy efficiency
of your data center while
confidently increasing
your kW per cabinet density
to increase utilization of your
data center space.
Reduce Operational Costs, Improve
Capacity Utilization, and Lower
Power Usage Effectiveness (PUE)*
Driven by explosive data processing growth, Data Center Managers face multiple, competing
demands: reducing operational costs, improving energy efficiency, and optimizing available
capacity, while sustaining a low total cost of ownership.
To meet these demands while minimizing the risk to service levels, the available data center
space is often underutilized while being overprovisioned with excess power and cooling capacity
regardless of actual IT equipment and space utilization. Today, a typical data center consumes
Factors Effecting Efficiency
• Inlet temperatures
• ∆T across heat exchanger
• Capacity utilization
about 3-5kW per cabinet due to power and cooling concerns, while the available cabinet space
can accommodate 15kW or more per cabinet if managed effectively.
As energy and construction costs continue to rise, over-provisioning and under-utilization are no
longer sustainable. Energy costs related to cooling account for approximately 37% of the overall
Efficiency Influencers
data center power consumption1 and are one of the fastest rising data center operational costs2.
• Inlet temperatures
• Set points
• Hot air/cold air leakage and recirculation
• Server/CRAH fan speeds
• kW per cabinet density
Air
Movement
12%
Enabling Improved Efficiency
• Seal every gap for complete separation
of cooling and exhaust air
• Direct cold air to where it needs to go
• Contain cooling and exhaust air for
maximum cooling capacity efficiency
• Monitor to maintain operational and
energy efficiency
Electricity
Transformer
UPS 10%
Lighting
Etc.,
3%
Cooling
25%
IT
Equipment
50%
Average data center energy usage allocation1
*Power Usage Effectiveness – a metric used to measure how effectively input power is used. It is expressed as a ratio of
power available to power used.
1 Average Data Center Energy Usage Allocation , Lawrence Berkeley National Laboratory 2007
2 451 Research has published 'Highly Energy-Efficient Datacenters in Practice,' October 2012
2
visit www.panduit.com/Cabinets
Power and cooling capacity remain the top targets for efficiency improvement and optimization of
cooling capacity is often the simplest way for data center operators to realize short term savings
and directly impact PUE3.
Panduit Labs research confirms that raising the supply air temperature in a data center is one of
the most effective means to reduce energy consumption. In addition, higher return temperatures
enable a higher CRAH ∆T across the heat exchangers allowing the cooling system to operate
more efficiently.
A key way to realize this energy efficiency potential and enable maximum capacity utilization is to
eliminate the mixing of cold and hot air within the cabinet and at the room level delivering higher
return air temperatures to the cooling system and allowing higher room set points.
1°C rise in chiller water temperature translates into
3-4% cooling system energy savings4.
3 How To Measure Energy Consumption In Your Data Center, Gartner Core RAS Research Note G00205428, 8 September 2010
4 Design Considerations for Datacom Equipment Centers ASHRAE 2005, ISBN 1-931862-94-X. Page 138
visit www.panduit.com/Cabinets
3
Complete Hot Air/Cold Air Separation is Critical
to Energy Efficiency and Capacity Utilization
Panduit’s Energy Efficient Data Center Cabinet System offers containment, in-cabinet ducting, and improved sealing that optimizes air separation and provide
superior energy savings compared to competitive offerings.
Optimized energy efficiency and capacity utilization begin with improved sealing. Even small air leaks within a cabinet will impact data center energy efficiency,
regardless of the heat load. Leaks allow hot air recirculation forcing IT equipment inlet fans to work harder and consume more energy, limiting per cabinet power
utilization. Panduit® Net-Access™ Cabinets reduce the air leakage typical in competitive cabinets by as much as 80%.
The graphics below illustrate the impact these leaks have on inlet temperatures. By preventing hot air recirculation, a more consistent inlet temperature gradient
can be realized across the entire front of the cabinet allowing the data center set point to be raised. This results in reduced cooling expense leading to the ability
to increase density power usage per cabinet, and increase available capacity.
Improved sealing coupled with containment leads to a $500 annual savings in cooling costs
per cabinet for high density applications at $ .10 per kWh at 15kW per cabinet7.
Inlet Air Temperature Gradients at
Front of Cabinets Comparison7
20kW
25kW
30kW
33kW
Panduit® Net-Access™ Cabinets
Annual Cooling Energy Costs
15kW
Impact of Net-Access™ Cabinet with
Net-Contain™ Containment System on
Cooling Energy Costs vs. Competition7
$120,000
$100,000
$80,000
$60,000
$40,000
$20,000
$0
Leading Network
Cabinet Competitor
Leading Server
Cabinet Competitor
Panduit
Leading Server Cabinet Competitor
Power per Cabinet
Leading
Network
Cabinet
Competitor
15kW
20kW
25kW
30kW
33kW
Scan to learn how Panduit delivered
a 27% energy savings with Energy
Efficient Cabinets and Containment.
With improved cabinet sealing, in-cabinet ducting, containment, and monitoring, the results show you can significantly
increase energy efficiency by raising the set point temperature in the entire data center.
4
visit www.panduit.com/Cabinets
7 Maximizing Cooling Energy Efficiency with Effective Cabinet Sealing, Panduit White Paper RKAT01-WW-ENG, March 2013
Increase Density to Optimize Data Center Capacity
Panduit Net-Access™ PDUs, integrated into thermally optimized Net-Access™ Cabinets, enable data center managers to realize higher capacity utilization and
reduced OpEx and CapEx costs.
Typical cabinets are loaded to 5 to 7kW on average, which is often far less than the physical space available within the cabinet resulting in overprovisioning or
the need to build expensive new whitespace.
15kW
Gartner estimates that data center floor
space costs $4,900 per cabinet annually
in CapEx and OpEx (excluding power
and cooling) regardless of
capacity utilization.*
5-7kW
$4,900 per Cabinet Space
Impact of Increasing Density
5
kW
5
kW
5
kW
5
5
kW kW
5
kW
5
kW
5
kW
5
5
kW kW
15
kW
15
kW
15
kW
100 kW
5
kW
5
kW
5
kW
5
5
kW kW
5
kW
15
kW
100 kW
5
kW
5
kW
5
5
kW kW
15
kW
15
kW
15
kW
$98,000
$34,300
Typical Density
High Density
Increasing the density of a 100kW data center can reduce
floor space costs from $98,000 to $34,300 and yield up to
$63,700 in annual savings versus competitive offerings.
visit www.panduit.com/Cabinets
5
Seal, Direct, Contain, and Monitor
to Improve your PUE
Panduit Energy Efficient Data Center Cabinet System provides
total separation allowing higher data center set points and
reduced cooling system energy consumption by up to 40%.5
Seal every gap for complete separation of
cooling and exhaust air
Net-Access™ Cabinets and Sealing Accessories eliminate leakage through
the cabinet structure preventing re-circulation of hot exhaust air back into
equipment inlets.
Direct cold air to where it needs to go
Net-Access™ In-Cabinet Ducting directs cool air directly into the
intake fans preventing recirculation and reducing inlet air temperature
by as much as 14°C, lowering fan energy consumption6.
Contain cooling and exhaust air for maximum
cooling capacity efficiency
Net-Contain™ Vertical Exhaust Duct and Cold Aisle Containment Systems
eliminate hot air recirculation and mixing with cold air allowing room and
chilled water temperature set points to be raised and PUE to be lowered.
Monitor to maintain operational and energy efficiency
Once the physical infrastructure has been optimized for thermal efficiency,
Panduit® SmartZone™ Solutions allow continuous monitoring
of highly accurate, granular PUE measurements in real-time to maintain
thermal efficiency in dynamic data center environments.
5 Impact of Air Containment Systems, Panduit White Paper #WP-20, June 2012
6 The Use of In-Cabinet Ducting to Improve Inlet Air Temperatures, Panduit White Paper RKAT02--WW-ENG, December 2012
6
visit www.panduit.com/Cabinets
Net-Contain™ Vertical
Exhaust Duct
FiberRunner ® and
Wyr-Grid ®Overhead Cable
Pathway Systems
Sealing
Accessories
Net-Access™
S-Type Cabinets
Net-Access™
N-Type Cabinets
Panduit® SmartZone™ Solutions
Software and Hardware
The Energy Efficient Data Center Cabinet System can be seamlessly integrated with all elements of the Panduit Converged Infrastructure Solutions, including
Overhead Cable Pathway Systems, High Speed Data Transport (HSDT) Cabling, Grounding and Bonding and Physical Infrastructure Systems.
visit www.panduit.com/Cabinets
7
Seal Every Gap for Complete Separation
of Cold Intake and Hot Exhaust Air
Complete Air Seal Features Reduce Air Leakage
Throughout the Cabinet Structure by as much as 25%7
Net-Access™ Cabinets have been designed to eliminate every
possible air gap other than those needed to mount equipment.
This minimizes by-pass air and recirculation in the cabinet
providing lower inlet temperatures.
Cabinet Top Seal
Net-Access™ Cabinets are provided with
pre-installed 1.5" x 5" or 3.5" x 5" cabinet top
covers and cable protection bezels to eliminate
air leakage from unused cable entry holes.
Cool Boot® Cabinet Top Air Sealing Fitting
Eliminate air leakage where data cable bundles enter
the cabinet.
Tool-Less Blanking Panels
Snap-In Panels optimize cooling efficiency
by eliminating bypass airflow and hot air
mixing in cabinets.
Scan to learn more about the
Cool Boot® product overview.
8
visit www.panduit.com/Cabinets
Cool Boot® Raised Floor Grommet
Stop bypass air in new or retrofit raised floor applications
where power and data cable pass through a cutout into a
rack or cabinet, saving $46 per floor tile cutout annually8.
7 Maximizing Cooling Energy Efficiency with Effective Cabinet Sealing, Panduit White Paper RKAT01-WW-ENG, March 2013
8 The Importance of Air Sealing Grommets to Improving Smart Data Center Cooling Efficiency, Panduit White Paper #WW-CPWP-04, August 2008
Direct Cold Air To Where It Is Needed
Net-Direct™ Inlet Ducts enable optimized containment
by effectively directing airflow to improve
network reliability
• Inlet duct solutions deliver cooling air directly from the
cold aisle into the intake fans of switches
• Inlet ducts are completely passive, requiring no energy
to operate and eliminating a point of failure
• Ensures front to back cooling airflow which enables
an effective deployment of network switches with
a Net-Contain™ Cold Aisle Containment deployment
• Inlet ducts enable reduced fan power energy consumption
by allowing lower fan speeds, improving the reliability
of the switch
Available for: Cisco^ Nexus, Catalyst and MDS Switches and Juniper EX Series Switches
Direct Hot Air To Where It Needs To Exhaust
Net-Direct™ Exhaust Ducts direct hot exhaust air out
of a cabinet away from adjacent devices within
non-contained environments
• Exhaust duct solutions channel hot exhaust air directly to
the hot aisle, away from the cold air inlet of adjacent switches
• Exhaust ducts are completely passive, requiring no energy
to operate and eliminating a point of failure
• Ensures switch exhaust airflow is directed to the hot aisle
enabling effective deployment of network switches with a
standard hot aisle/cold aisle configuration
• Exhaust ducts enable reduced fan power energy consumption
by allowing lower fan speeds, improving the reliability
of the switch
Patented9 In-Cabinet Ducting optimizes cooling system efficiency by establishing front-to-back airflow
patterns through the cabinet.
Available for: Cisco^ Nexus and Catalyst Switches
^Cisco is a registered trademark of Cisco Technology, Inc.
9 Patents #8,035,965, #7,855,885 and #7,595,985 - Network Cabinet with Thermal Air Flow Management System
visit www.panduit.com/Cabinets
9
Contain Cold Air or Hot Air to Maximize Cooling
and Space Capacity Utilization
Net-Contain™ Aisle Containment Systems
Deliver Efficient Cooling for High Density Applications
Data Center Managers, challenged to maximize the utilization of available rack-space and cooling capacity, often increase the power density per cabinet.
As cabinet power densities rise, containment architectures are the optimal approach, ensuring uniform cooling air temperature is delivered to equipment in
high density PODs allowing full utilization of available cabinet space and cooling capacity.
Scan to view the Panduit® Net-Contain™ Cold Aisle Containment
Application at EMC’s Durham North Carolina Data Center.
Net-Contain™ Aisle Containment System Benefits
• Data Center Design Versatility – Translucent panels provide built-in provisions for fire suppression, environmental monitoring,
security devices and other utilities to accommodate all application requirements
• Complete Application Flexibility – System can be used for slab floor or raised floor applications. Modular design enables varying
aisle widths and accommodates intermixed Net-Access™ Cabinet widths and in-row coolers to support various network architectures
and heat densities
• Reduced Operational Costs – Sliding doors allow easy accessibility for efficient moves, adds and changes and automatically return
to closed position optimizing air containment. Net-Contain™ Components are engineered to seal, minimizing leakage to less than 3%
10
visit www.panduit.com/Cabinets
Net-Contain™ Vertical Exhaust Duct
Passive Cooling for High Density Applications
Net-Contain™ Vertical Exhaust Duct (VED) Systems optimize cooling energy utilization to support high density heat loads to enable 30kw or greater per cabinet.
VEDs passively separate hot exhaust air from cooling air and direct hot exhaust air from active equipment into the Computer Room Air Handler (CRAH)
air return system, allowing higher return air temperature improving CRAH and heat exchanger system efficiency up to 40% or more.
Above Ceiling Hot Air Return
Cold
Aisle
Cold
Aisle
Hot
Aisle
Hot
Aisle
Cold
Aisle
Cold
Aisle
Raised Floor Cold Air Supply*
Typical Data Center
•Cool air does not reach the top portions of the cabinets,
making servers in the top rack units vulnerable to overheating
•Hot exhaust air follows complex airflow path back to
CRAH units
Cold
Aisle
Cold
Aisle
Hot
Aisle
Hot
Aisle
Cold
Aisle
Raised Floor Cold Air Supply*
Typical Data Center
•Cool air does not reach the top portions of the cabinets,
making servers in the top rack units vulnerable to overheating
•Hot exhaust air follows complex airflow path back to
®
™
Scan to view the Panduit
CRAH unitsNet-Contain Vertical
Exhaust Duct Application at Cisco Allen Data Center.
Cold
Aisle
Hot
Aisle
Cold
Aisle
Hot
Aisle
Cold
Aisle
Raised Floor Cold Air Supply*
Data Center Utilizing Panduit ® Net-Contain™
Vertical Exhaust Duct
•Uniform distribution of cool air reaching the top of the cabinet
•Hot exhaust air is isolated and ducted directly to CRAH units
Net-Contain™ Vertical Exhaust Duct System Benefits
• Flexibility and Versatility – Multiple sizes, heights and adjustable height features allow system to adapt to virtually any data center
structure including slab floors or raised floors and facilities with or without drop ceilings
• Speed Deployment and Reduce Installation Cost – Fast, simple assembly and integral ceiling seal reduce installation time
by 30% compared to competitive offerings
• Enhance Your Data Center Environment – Vertical Exhaust Duct and Net-Access™ Cabinets with sealed, solid rear doors dampen
equipment noise
• Bond Vertical Exhaust Duct with single connection improves system reliability and protection to personnel – Entire VED
is fully electrically bonded to the cabinet requiring no grounding whips for protection of equipment and personnel
visit www.panduit.com/Cabinets
•Un
•Ho
Above Ceiling Hot Air Return
Above Ceiling Hot Air Return
Data
Verti
11
Monitor to Maintain Operational
and Energy Efficiency
Data center managers are challenged to maintain and manage energy efficiency gains in a highly dynamic, virtualized environment in which power consumption,
environmental and capacity utilization variables are constantly changing. Without the ability to monitor these variables in the data center, efficiency gains, PUE
reductions and the ability to maximize capacity utilization while maintaining SLA’s will erode over time leading to a higher total cost of ownership.
PUE
2.0
OPEX
increases as
PUE Rises
Un-Monitored
PUE
1.5
1.0
Increased
TCO
Energy Efficiency Managed
when Monitored with
Panduit® SmartZone™ Solutions
Time
Panduit® SmartZone™ Solutions
Enable Real-Time Monitoring, Visualization, and Reporting
Panduit® SmartZone™ Solutions offer software, hardware and services that provide management information by monitoring power and environmental
conditions in real time from the entire facility, down into individual cabinets. This capability enables the data center manager to optimize capacity and reduce
CapEx and OpEx costs.
Power and environmental monitoring is only one component of Panduit’s DCIM offering. SmartZone™ Software also enables the tracking, allocation,
and utilization of critical IT assets within your data center.
12
visit www.panduit.com/Cabinets
Rack Power Distribution Units (PDUs)
Power and Environmental Hardware
As power densities increase, monitoring of power and environmental information using an intelligent rack power distribution unit (PDU) is critical to
preventing power overload and downtime. Panduit supports power and environmental management through two distinct intelligent PDU families:
SmartZone™ Network-Enabled Rack PDUs that connect directly to the network and SmartZone™ Gateway-Enabled Rack PDUs which connect
via a gateway. SmartZone™ Rack PDUs integrate seamlessly into Panduit® SmartZone™ Software, enabling real-time monitoring of physical
infrastructure power consumption, temperature, and humidity levels for enhanced system reliability and operational efficiencies. (See pages 34
and 37 for a list of PDU and sensor part numbers).
Panduit’s comprehensive rack PDU offering is available globally in a variety of power configurations to match typical applications, and can be
configured to meet customer specific needs.
Rack Power Distribution Units (PDUs) – Safely and efficiently manage and distribute power to multiple devices through a single
power connector to enhance scalability of network build outs.
Through integration with the SmartZone™ Software Suite, rack PDUs send power and temperature readings to allow:
• Automated documentation and visualization of power utilization and environmental conditions
• Recognition and notification of faults or power disruptions
• Identification of available related capacity
Environmental Sensors – Environmental Sensors are available in wired or wireless options, to measure and trend environmental
conditions such as temperature and humidity levels, at the cabinet level. These intelligent sensors transmit real-time environmental information,
providing notification of exceeded thresholds to quickly identify and resolve issues, identify hot and cold spots in the data center and automate
collection of real-time and accurate environmental information.
These sensors send cabinet-level information to the SmartZone™ Software to allow:
• Automated documentation and visualization of temperature and humidity levels
• Recognition and notification of exceeded temperature thresholds and/or other environmental-specific concerns
• Trending analysis to uncover developing thermal issues that may impact optimal performance and efficiency
visit www.panduit.com/Cabinets
13
Net-Access™ N-Type Cabinets
Optimum Accessibility and Cable Management for High Density Applications
Net-Access™ N-Type Cabinets are the first choice for data center managers and systems
integrators specifying high density network, storage and compute applications that
require optimal thermal management and the capacity to manage high cable densities.
Integral cabinet air seal features and integration with passive hot and cold air containment
components drive efficient utilization of cooling capacity and reduce cooling energy
consumption. The Net-Access™ inset frame design efficiently manages large quantities of
cables and provides space for unmatched access reducing operational costs. This industry
leading design also maximizes airflow and provides easy access to equipment for ongoing
operational efficiencies, providing exceptional value in a 800mm (31.5") wide enclosure.
Inset frame provides up to 10%
more space for cable management
and cooling airflow
Industry leading inset cabinet frame posts
create a large area for airflow to provide
proper heat dissipation and enable easy
access to equipment, in-cabinet ducting
and cabling, speeding deployments and
reducing operational costs.
Dual hinged doors speed deployments
and moves, adds, and changes up to 30%
IT staff is scarce, downtime is expensive.
For a 120 rack dynamic data center, our
cabinets save you up to an hour a day,
adding up to $18,250 per year savings
for your staff.
Efficiently manage high
cable densities
Modular snap in fingers align with rack
spaces to simplify cable management,
providing proper bend radius control and
organizing cables for faster moves, adds
and changes and installations.
14
visit www.panduit.com/Cabinets
Open rail mounting creates more
cable management space and
equipment positioning flexibility
High strength frame eliminates need for
support members between rails, providing
unobstructed space between the frame
and the side panels.
Vertical split side panels
enable fast access to equipment
Innovative vertical split side panels
and optional vertical split hinged side
panels allow fast easy access to end
of row network equipment and cabling,
eliminating time consuming handling.
Innovative Leveling Feet Design
Reduces Cabinet Installation
Time up to 80%
Heavy duty, M14 thread top drive
leveling feet are easily accessed and
allow cabinets to be leveled in less time
than typical leveling feet.
Bond cabinets to the
telecommunications grounding
infrastructure with single connection,
reducing installation time
Entire cabinet is fully electrically
bonded, requiring no grounding whips
to doors or side panels for protection
of equipment and personnel.
visit www.panduit.com/Cabinets
15
Net-Access™ S-Type Cabinets
Cost Effective and Versatile Cabinets for all Data Center
Applications and Facilities Designs
Net-Access™ S-Type Cabinets provide data center managers and systems integrators an
unprecedented range of features in a cost effective cabinet platform for server, network,
and pre-configured cabinet applications.
Integral cabinet air seal features and seamless integration with passive hot and cold air containment
components provide efficient utilization of cooling capacity, and contribute to reduced cooling energy
consumption. An innovative frame design maximizes RU utilization saving as much as 15% of the floor
space while safely accommodating equipment loads. Offered in a variety of widths, heights,
and depths, they can be specified for a variety of applications in any facility to meet the diverse
application needs of today’s data centers.
800mm (31.5") W
700mm (28") W
600mm (24") W
Large selection of standard cabinet widths, heights, and depths offered in:
16
• 600mm (24"), 700mm (28"), and 800mm (31.5") Widths
• 1070mm (42") and 1200mm (48") Depths
• 42 RU, 45 RU, and 48 RU Heights
• Black and White Color Option
• Static Load Rating 1,364kg (3,000 lb.)
• Rolling Load Rating 1,136kg (2,500 lb.)
visit www.panduit.com/Cabinets
Out-Set Cable Entry Improves
Floor Space Utilization up to 5%
Network cable entry locations are
outside of equipment area, allowing
top 2 RUs to be used, optimizing
cabinet utilization and saving
floor space.
Zero RU E-Rail Vertical Patching Adds
Capacity and Improves Floor Space
Utilization by 10%
Unique Zero RU E-Rail is the industy's
only vertical patching system for 600mm
(24") wide cabinets integrating with
Quick-Net™ Copper and Fiber Cabling
Systems, optimizing cabinet utilization
and saving floor space.
Innovative Leveling Feet Design
Reduces Cabinet Installation
Time by 80%
Heavy duty, M14 thread top drive
leveling feet are easily accessed and
allow cabinets to be leveled in less time
than typical leveling feet.
A 15% savings in floor space means you can build a 420 server POD
with 10 server cabs versus a competitors' cabinet that would require
12 server cabinets to hold equivalent amount of servers.
CapEx savings10 $900/ft2 x 16ft2 = $14,400 capital savings per POD.
10) Cost Model: Dollars per kW plus Dollars per Square Foot of Computer Floor, Uptime 2008
visit www.panduit.com/Cabinets
17
Simplify and Accelerate Data Center Deployments
Net-Access™ Cabinets Enable Convergence of Network Equipment
Converged Infrastructure Solutions Add Value
and Reduce Installation Time and Cost
Dynamic rated Net-Access™ N-Type and S-Type Cabinets allow
pre-installation of IT equipment for faster deployments and time to
production. Panduit Converged Infrastructure Solutions are fully tested and
validated physical infrastructures that ensure best practice installations
and optimal system performance. Each configuration accelerates
deployment and promotes rapid upgrades requiring zero reconfigurations
and downtime.
Fast, Single Part Number Quoting and Procurement
Simply attach pre-priced, robust Converged Infrastructure Solutions to
active gear quotes:
• Reduce quote time
• Procure complete infrastructures with a single part number
• Ensure accurate delivery of all parts to the job site
Maximize the Speed of Deployment and
Overall Execution
Converged Infrastructure Solutions can save up to 80% in deployment time.
• Solutions arrive pre-assembled, kitted, and ready to rack and roll
• Factory installed cable managers, patch cable kits, and cabling
instructions ensure a precise deployment and
professional appearance
Converged Infrastructure for
Nexus 7009 "Heavy Copper"
Deployment
Fulfillment
Time to Production
Design
Plan
Assess
Typical
Panduit Converged
Infrastructure Solutions
^Cisco is a registered trademark of Cisco Technology, Inc.
18
visit www.panduit.com/Cabinets
Reduced Time to Production
up to 80%
Arrive factory designed, tested,
and validated to improve:
• Assessment time up to 80%
• Planning time up to 80%
• Design time up to 80%
• Fulfillment time up to 90%
• Deployment time up to 65%
Refer to Panduit Converged
Infrastructure Solutions For Cisco^
Nexus, UCS, and Catalyst Platforms,
RKCB34--SA-ENG
Major Private Cloud Provider
reduced system assembly
time by up to 7 hours per
cabinet, improving cost
and speeding delivery.
Net-Access™ Cabinet and Thermal Management
Solution for Cisco^ Nexus 7018 Switch
Panduit offers a Net-Access™ Cabinet solution designed to meet the thermal and
operating requirements of the modular, high density Cisco^ Nexus 7018 Switch.
Based on a standard 800mm (31.5") wide Net-Access™ N-Type Cabinet, an
easy to use expansion module provides space to route and manage high
densities of cables. Internal ducting enables front to back cooling air flow
and improved reliability.
Simple conversion for
Standard 800mm N-Type Cabinet
Extension kit enables 800mm
Net-Access™ N-Type Cabinet to be
extended to 1,000mm (40") wide, reducing
shipping costs and simplifying handling.
Passive inlet and exhaust duct
ensures cooling airflow
Prevents recirculation of exhaust air into
the switch, ensuring lower inlet temperature
and reduced fan energy consumption.
Cable management fingers
route, manage and protect
high cable densities
Net-Access™ N-Type Cabinet with Cisco^ Nexus 7018
Extension Kit Installed
Fingers align with rack spaces to
ensure proper bend radius and superior
management of high densities of I/O
cables, keeping them clear of cold air
flow while maintaining access to power
supplies and fan modules, reducing
operational costs.
^Cisco is a registered trademark of Cisco Technology, Inc.
visit www.panduit.com/Cabinets
19
Net-Access™ Integral Cabinet Top Cable Routing System
Speed deployments and optimize overhead space utilization
Net-Access™ Cabinets are available with an Integral Cabinet Top Cable Routing System that protects, routes, and manages large
quantities of twisted pair data cables into and out of any Net-Access™ Cabinet. This versatile system is integral to the top of the cabinet
and easily integrates with other cable pathways used throughout the data center, providing up to a 30% reduction in installation costs.
Net-Access™ Integral Cabinet Top Cable Routing System deployed on Net-Access™ Cabinets.
20
visit www.panduit.com/Cabinets
Net-Access™ N-Type Cabinet Specifications
• Welded and assembled steel frame construction
• Easy maintenance powder coat finish
• Adjustable rear equipment rails with continuous positioning,
fixed front rails
• Large cable entry/cable access
• Doors include keyed swing handles
• Side panels
• Dual hinge door for maximum accessibility between
adjacent cabinets
• Cabinet supplied with 2 sets of high density cable management fingers (SN25F)
• Cable entry holes are equipped with plastic sealing plugs
• UL 2416 standard compliant and have been static load tested to
1,360kg (3,000 lb.)
• EIA-310-E compliant
• Rolling Load of 1,136kg (2,500 lb.)
• Cabinet ships assembled, one per pallet
• N-Type Cabinets include hardware kit: #12-24 screws,
or M6 screws and cage nuts
• Casters are supplied separately
Net-Access™ S-Type Cabinet Specifications
• Welded and assembled steel frame construction
• Easy maintenance powder coat finish
• Adjustable rear equipment rails with continuous positioning,
fixed front rails
• Doors include keyed swing handles
• Side panels include keyed quarter-turn latches
• Large cable entry/cable access
• PDU brackets (SPDUBRK) included
• Cable entry holes are equipped with plastic sealing plugs
• UL 2416 standard compliant and have been static load tested to
1,360kg (3,000 lb.)
• EIA-310-E compliant
• Rolling Load of 1,136kg (2,500 lb.)
• Cabinet ships assembled, one per pallet
• S-Type Cabinets include hardware kit: M6 screws, and cage nuts
• Vertical airdams included
• Casters are pre-installed
Net-Access™ Cable Capacity Charts
Top Cap Opening Cable Capacity
Area
Cable Capacities
Opening Size
5" x 3.5"
In.2
15.6
Cm.2
100.7
Cat. 6A
0.354"
(8.99mm)
63
5" x 1.5"
6.5
42.2
26
Cat. 6A
0.310"
(7.87mm)
82
Cat. 6A
0.297"
(7.54mm)
90
Cat. 6
0.250"
(6.35mm)
127
Cat. 5e
0.187"
(4.75mm)
227
Fiber
(3mm)
569
QuickNet™
Cassettes
8
34
37
53
95
239
8
Cable Pathways (Per Side)
Area
Cable Capacities
In.2
Cm.2
Cat. 6A
0.354"
(8.99mm)
800x1070
43.8
282.7
178
232
252
357
638
1599
800x1200
43.8
282.7
178
232
252
357
638
1599
Cabinet Size
(mm)
Cat. 6A
0.310"
(7.87mm)
Cat. 6A
0.297"
(7.54mm)
Cat. 6
0.250"
(6.35mm)
Cat. 5e
0.187"
(4.75mm)
Fiber
(3mm)
N-Type (Front Side)
S-Type (Rear Side)
600x1070
18.5
119.4
75
98
106
150
269
675
600x1200
30.5
196.8
123
161
176
248
444
1113
700x1070
32.4
208.9
131
171
186
263
471
1181
700x1200
53.4
344.4
216
282
308
434
777
1948
800x1070
46.3
298.4
187
245
267
376
673
1688
800x1200
76.3
491.9
309
404
440
621
1110
2783
visit www.panduit.com/Cabinets
21
Net-Access™ N-Type and S-Type Cabinet
Offering and Availability Overview
Multiple cabinet solutions to meet your project goals – from standard cabinets for quick turnaround to customer configured cabinet
for specific deployments, Net-Access™ N-Type and S-Type Cabinets provide a complete solution to meet customer requirements.
Quick
Turnaround
Net-Access™ N-Type and S-Type Standard Cabinets
Net-Access™ N-Type and S-Type Standard Configured Cabinets
Net-Access™ N-Type and S-Type Customer Configured Cabinets
Build to
Order
Options
N-Type and S-Type
Standard Cabinets
N-Type and S-Type
Standard Configured Cabinets
• Quick turnaround
•3 widths – 600mm, 700mm, 800mm
•2 heights – 42 RU, 45 RU
•2 depths – 1070mm, 1200mm
•With or without side panels
•Black finish
•Standard doors
N-Type and S-Type
Customer Configured Cabinets
•3 widths – 600mm, 700mm, 800mm
•3 heights – 42 RU, 45 RU, 48 RU
•2 depths – 1070mm, 1200mm
•With or without side panels
•Black or white finish
•Door options
•Thermal options
•Equipment rail options
•Top cap options
•Caster options
•Configured to customer specifications
•Multiple widths
•Multiple heights
•Multiple depths
•With or without side panels
•Black, white or gray finish
•Door options
•Thermal options
•Equipment rail options
•Top cap options
•Caster options
•Standard accessories pre-installed
to customer specifications
Net-Access™ N-Type and S-Type Standard Cabinets
N-Type Width
With Side Panels
Without Side
Panels
800mm
800mm
700mm
600mm
42 RU
N8212B
S8212B
S7212B
S6212B
45 RU
N8512B
S8512B
S7512B
S6512B
42 RU
N8222B
S8222B
S7222B
S6222B
45 RU
N8522B
S8522B
S7522B
S6522B
42 RU
N8219B
S8219B
S7219B
S6219B
45 RU
N8519B
S8519B
S7519B
S6519B
42 RU
N8229B
S8229B
S7229B
S6229B
45 RU
N8529B
S8529B
S7529B
S6529B
N-Type Standard Components:
•#12-24 tapped rails
•Dual hinge front door/split rear door
•No PDU brackets
•Two sets of fingers
•Solid side panels
•No casters
22
S-Type Width
visit www.panduit.com/Cabinets
S-Type Standard Components:
•Cage nut rails
•Single hinge front door/split rear door
•Caster and PDU brackets included
• Cable management optional
1070mm depth
1200mm depth
1070mm depth
1200mm depth
Net-Access™ N-Type Standard Configured Cabinets
Series
Width
Height
Depth
Side Panels
Color
N
8 = 800mm
2 = 42 RU
1 = 1070mm
2 = 2 Side Panels*
B = Black
C = Cage Nut Rails
5 = 45 RU
2 = 1200mm
9 = No Side Panel
W = White
E = Single Hinge Front Door and Cage Nut Rails
8 = 48 RU
Standard Options (Select Only One)
S = No Doors**
T = Integral Cabinet Top Cable Routing System**
TC = Integral Cabinet Top Cable Routing System and
Cage Nut Rails
U = Vertical Blanking and Cage Nut Rails
V = VED Ready**
Y = VED Ready and Cage Nut Rails
YT = VED Ready, Cage Nut Rails, and Integral Cabinet Top
Cable Routing System
*Standard side panel. **Includes #12-24 tapped equipment rails. V, Y and YT - Only available for 1200mm deep cabinets. See page 25.
Standard Configurations have 6 characters with only one standard option suffix.
N
8
2
1
2
B
Net-Access™ S-Type Standard Configured Cabinets
Series
Width
Height
Depth
Side Panels
Color
S
6 = 600mm
2 = 42 RU
1 = 1070mm
2 = 2 Side Panels*
B = Black
7 = 700mm
5 = 45 RU
2 = 1200mm
9 = No Side Panel
W = White
8 = 800mm
8 = 48 RU
Standard Options (Select Only One)
A = Switch Configured with Front Cable Management
(PDU bracket not included)
A9 = Switch Configured with Front Cable Management and
No Casters
F = Vertical Cable Management Fingers
P = Vertical Patching Equipment Rails
S = No Doors
T = Integral Cabinet Top Cable Routing System
T9 = Integral Cabinet Top Cable Routing System and
No Casters
V = VED Ready
V9 = VED Ready and No Casters
9 = No Casters
*Standard side panel. P - Only available for 600mm wide S-Type Cabinets. V and V9 - Only available for 1200mm deep cabinets. See page 25.
Standard Configurations have 6 characters with only one standard option suffix.
S
6
2
1
2
B
Net-Access™ N-Type and S-Type Customer Configured Cabinets
Cabinets can be configured to customers' specifications. Multiple options are listed below, below, but may not be available for all
configurations. For other possible options please contact your sales person or Customer Service.
•Multiple Widths
•Multiple Heights
•Multiple Depths
•Doors – Single Hinge, Dual Hinge,
Split Doors, or None
•Side Panels – 0, 1, or 2
•Black, White or Gray Finish
•#12-24 Tapped or Cage Nut Rails
•Standard, VED, Integral Cabinet Top Cable
Routing System, or VED and Integral Cabinet
Top Cable Routing System
• Vertical Patching
• Vertical Air Dams
• Cable Management
• Casters
• PDU Brackets
•Combination Locks
visit www.panduit.com/Cabinets
23
Net-Access™ N-Type and S-Type Cabinets with
Integral Cabinet Top Cable Routing System
N-Type Width
With Side Panels
Without Side
Panels
S-Type Width
800mm
800mm
700mm
600mm
42 RU
N8212BT
S8212BT
S7212BT
S6212BT
45 RU
N8512BT
S8512BT
S7512BT
S6512BT
48 RU
N8812BT
S8812BT
S7812BT
S6812BT
42 RU
N8222BT
S8222BT
S7222BT
S6222BT
45 RU
N8522BT
S8522BT
S7522BT
S6522BT
48 RU
N8822BT
S8822BT
S7822BT
S6822BT
42 RU
N8219BT
S8219BT
S7219BT
S6219BT
45 RU
N8519BT
S8519BT
S7519BT
S6519BT
48 RU
N8819BT
S8819BT
S7819BT
S6819BT
42 RU
N8229BT
S8229BT
S7229BT
S6229BT
45 RU
N8529BT
S8529BT
S7529BT
S6529BT
48 RU
N8829BT
S8829BT
S7829BT
S6829BT
For other colors replace suffix B (Black) with W (White).
N-Type Integral Top Cabinet Components:
•12-24 tapped rails
•Dual hinge front door/split rear door
•No PDU brackets
•Two sets of fingers
•No casters
24
visit www.panduit.com/Cabinets
S-Type Integral Top Cabinet Components:
•Cage nut rails
•Single hinge front door/split rear door
•No cable management
•Caster and PDU brackets included
1070mm depth
1200mm depth
1070mm depth
1200mm depth
Net-Access™ N-Type and S-Type Vertical Exhaust Duct
(VED) Cabinets (VED Sold Separately)
N-Type Width
800mm
With Side Panels
Without Side
Panels
S-Type Width
800mm
700mm
600mm
42 RU
N8222BV
S8222BV
S7222BV
S6222BV
45 RU
N8522BV
S8522BV
S7522BV
S6522BV
48 RU
N8822BV
S8822BV
S7822BV
S6822BV
42 RU
N8229BV
S8229BV
S7229BV
S6229BV
45 RU
N8529BV
S8529BV
S7529BV
S6529BV
48 RU
N8829BV
S8829BV
S7829BV
S6829BV
1200mm depth
1200mm depth
* VED cabinets only available in 1200mm depths.
For other colors replace suffix B (Black) with W (White).
N-Type VED Cabinet Components:
S-Type VED Cabinet Components:
•#12-24 tapped rails
•Dual hinge front door/solid rear door
•No PDU brackets
•2 sets of fingers
•VED top cap ready
•Vertical blanking panels with pass-throughs
•Rear floor seals
•No casters
•Cage nut rails
•Single hinge front door/solid single hinge rear door
•No cable management
•VED top cap ready
• Vertical blanking panels
•Front and rear floor seals
•Caster and PDU brackets included
Net-Contain™ Vertical Exhaust Ducts (VEDs)
Part Number
Description
Net-Contain™ Vertical Exhaust Duct for Net-Access™ N-Type and S-Type Cabinets
C2VED**I1626^^
Net-Contain™ VED **mm width cabinet – 406mm (16") up to 660mm (26") height – ^^ colored.
C2VED**I2638^^
Net-Contain™ VED **mm width cabinet – 660mm (26") up to 965mm (38") height – ^^ colored.
C2VED**I3866^^
Net-Contain™ VED **mm width cabinet – 965mm (38") up to 1,676mm (66") height – ^^ colored.
** = 08 = 800mm, 07 = 700mm, 06 = 600mm ^^ = B1 = Black, W1 = White.
visit www.panduit.com/Cabinets
25
Net-Contain™ Cold and Hot Aisle Containment
Part Number
Description
Net-Contain™ Aisle Containment Sliding Doors
C2CACT5F**SD^^
Net-Contain™ Sliding Door CAC for **ft (**mm) aisle- capable of 42 up to 45 RU – ^^ colored.
** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.
Net-Contain™ Integral Low Profile Ceiling Structure for Net-Access™ N-Type and S-Type Cabinets
C2CAC08F**IR^^
Net-Contain™ (CAC) Integral Roof for 800mm width cabinet with **ft (**mm) aisle width – ^^ colored.
C2CAC07F**IR^^
Net-Contain™ (CAC) Integral Roof for 700mm width cabinet with **ft (**mm) aisle width – ^^ colored.
C2CAC06F**IR^^
Net-Contain™ (CAC) Integral Roof for 600mm width cabinet with **ft (**mm) aisle width – ^^ colored.
** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.
Net-Contain™ Integral Roof Wall Panels
C2CAC**F08WP^^
Net-Contain™ Integral Roof Wall Panel for **mm width cabinet – ^^ colored.
** = 08 = 800mm, 07 = 700mm, 06 = 600mm ^^ = B1 = Black, W1 = White.
Net-Contain™ Row Base Cooling Blanking Panels
C2CAC**ABWPA^^
For cold aisle containment systems using row base cooling equipment.
** = 06 = 600mm, 04 = 400mm, 03 = 300mm ^^ = B1 = Black, W1 = White.
Net-Contain™ Aisle Containment Sliding Doors
C2CACT5F04SD^^
Net-Contain™ Sliding Door CAC for 4 ft. (1200mm) aisle- capable of 42 up to 45 RU – ^^ colored.
^^ = B1 = Black, W1 = White
Sliding Door Frame Adapter for 4' (1200mm) Aisle Containment Sliding Doors
C2HACT8F04DFB1^^ Net-Contain™ Hot Aisle Containment Sliding Door Frame Adapter for 4 ft. (1200mm) aisle, capable of 42 RU
up to 48 RU.
^^ = B1 = Black, W1 = White
C2HACT8F04DFB
Net-Contain™ Adjustable Vertical Wall for Net-Access™ N-Type and S-Type Cabinets
C2HAC**I1626^^
Net-Contain™ Hot Aisle Containment Adjustable Vertical Wall (16" - 26") for **mm width cabinets.
C2HAC**I2638^^
Net-Contain™ Hot Aisle Containment Adjustable Vertical Wall (26" - 38") for **mm width cabinets.
C2HAC**I3866^^
Net-Contain™ Hot Aisle Containment Adjustable Vertical Wall (38" - 66") for **mm width cabinets.
** = 06 = 600mm, 04 = 400mm, 03 = 300mm ^^ = B1 = Black, W1 = White.
C2HAC**I1626
C2HAC**I2638
C2HAC**I3866
Adjustable EOR Vertical Wall
C2HACERI1626^^
Net-Contain™ Adjustable End of Row Vertical Wall (16" - 26") for 900mm/1000mm/1200mm aisle widths.
C2HACERI2638^^
Net-Contain™ Adjustable End of Row Vertical Wall (26" - 38") for 900mm/1000mm/1200mm aisle widths.
C2HACERI3866^^
Net-Contain™ Adjustable End of Row Vertical Wall (38" - 66") for 900mm/1000mm/1200mm aisle widths.
^^ = B1 = Black, W1 = White
C2HACERI1626
C2HACERI2638
C2HACERI3866
26
visit www.panduit.com/Cabinets
Net-Contain™ Universal Aisle Containment System
Part Number
CUEFRT8F**ST
CUEFRT9F**ST
Description
Net-Contain™ End of Row Frame for Roofing
CUEFRT8F**ST^^
Net-Contain™ UAC End of Row Frame for Roofing - 42/45 RU high.
CUEFRT9F**ST^^
Net-Contain™ UAC End of Row Frame for Roofing - 48/52 RU high.
** 04 = 4' (1200mm) aisle width, 06 = 6' (1800mm aisle width) ^^ = B1 = Black, W1 = White.
Net-Contain™ Mid-Span Post
CUSMPR52ST01B1
CUSMPR52ST01B1
Net- Contain™ Mid-Span Post 42 RU to 52 RU high.
Net-Contain™ Mid-Span Cabinet Support
CUCMSS**ST01NC
CUCMSS**ST01NC
Net-Contain™ Mid-Span Cabinet Support
**03 = 300mm, 06 = 600mm
Net-Contain™ Aisle Containment Sliding Doors
C2CACT5F**SD^^
C2CACT5F**SD
Net-Contain™ Sliding Door CAC for **ft (**mm) aisle- capable of 42 up to 45 RU – ^^ colored.
** = 04 = 4ft (1200mm), 06 = 6ft (1800mm) ^^ = B1 = Black, W1 = White.
Net-Contain™ Integral Ceiling Structures
CURFS06F**HB
CURFS07F**HB
CURFS08F**HB
CURFS06F**HB^^
Net-Contain™ 600mm Roofing Section.
CURFS07F**HB^^
Net-Contain™ 700mm Roofing Section.
CURFS08F**HB^^
Net-Contain™ 800mm Roofing Section.
** 04 = 4' (1200mm) aisle width, 06 = 6' (1800mm aisle width) ^^ = B1 = Black, W1 = White.
Net-Contain™ End of Row Frame for Vertical Walls 42/45 RU High
CUEFVT8F04ST^^
C2HACERI1626
C2HACERI2638
C2HACERI3866
CUVWA06S**ST
Net-Contain™ End of Row Frame for Vertical Walls - 42/45RU - 4ft. (1200mm) aisle width.
^^ = B1 = Black, W1 = White.
Adjustable EOR Vertical Wall
C2HACERI1626^^
Net-Contain™ Adjustable End of Row Vertical Wall (16" - 26") for 900mm/1000mm/1200mm aisle widths.
C2HACERI2638^^
Net-Contain™ Adjustable End of Row Vertical Wall (26" - 38") for 900mm/1000mm/1200mm aisle widths
C2HACERI3866^^
Net-Contain™ Adjustable End of Row Vertical Wall (38" - 66") for 900mm/1000mm/1200mm aisle widths.
^^ = B1 = Black, W1 = White
Net-Contain™ Vertical Wall Adapter
CUVWA06S**ST^^
C2HAC**I1626
C2HAC**I2638
C2HAC**I3866
CUVWB12S12ST
Net-Contain™ Vertical Wall Adapter
**06 = 600mm, 07 = 700mm, 08 = 800mm ^^ = B1 = Black, W1 = White.
Net-Contain™ Adjustable Height Vertical Walls
C2HAC**I1626^^
Net-Contain™ Adjustable Vertical Wall (16" - 26").
C2HAC**I2638^^
Net-Contain™ Adjustable Vertical Wall (26" - 38").
C2HAC**I3866^^
Net-Contain™ Adjustable Vertical Wall (38" - 66").
**06 = 600mm, 07 = 700mm, 08 = 800mm ^^ = B1 = Black, W1 = White.
CUWBSS**ST01
Net-Contain™ Vertical Wall Brace
CUVWB12S12ST^^
Net-Contain™ Vertical Wall Brace, 4 ft. (1200mm) aisle width.
^^ = B1 = Black, W1 = White.
CUWBPS**ST02
Net-Contain™ Wall Beam
CUWBSS**ST01^^
Net-Contain™ Wall Beam, 1 piece.
CUWBPS**ST02^^
Net-Contain™ Wall Beam, 2 pieces.
**06 = 600mm, 07 = 700mm, 08 = 800mm, 24 = 2400mm ^^ = B1 = Black, W1 = White.
CUFBPR**06HB
Net-Contain™ Full Blanking Panel
CUFBPR**06HB^^
Net-Contain™ Full Blanking Panel 600mm wide.
**42 = 42 RU, 45 = 45 RU, 48 = 48 RU, 52 = 52 RU ^^ = B1 = Black, W1 = White.
CUTBPR0610HBN1
Net-Contain™ Top of Cabinet Blanking Panel
CUTBPR0610HBN1
Net-Contain™ Top of Cabinet Blanking Panel 600mm high x 1000mm wide.
visit www.panduit.com/Cabinets
27
Net-Access™ Cabinet Accessories
Part Number
N-Type
S-Type
Compatible Compatible
Description
POU Brackets and Cable Management
SN15F
S7VPPB
NERSS
SN25F
SN8VPPB
NACSS
NVPDUB
SPDUBRK
SN15F
x
SN25F
x
S7VPPB
SN8VPPB
x
x
Finger Kit, 100mm (3.9") depth that attaches to posts on 42 RU through 48 RU cabinets.
x
Finger Kit, 150mm (5.9") depth that attaches to posts on 42 RU through 48 RU cabinets.
x
Vertical patching bracket for 700mm wide cabinets.
x
Vertical patching bracket for 800mm wide cabinets.
NERSS
x
End of row slack spool.
NACSS
x
Center slack spool for between cabinets, adjustable 210mm (8.3") to 267mm (10.5") .
NVPDUB
x
PDU brackets, sold in pairs.
SPDUBRK
x
PDU brackets, sold in pairs.
S2BRK6
x
Combination PDU/cable management bracket, 152mm (6") wide full length for
42 RU through 48 RU cabinet.
S2BRK12
x
Combination PDU/cable management bracket, 305mm (12") wide full length for
42 RU through 48 RU cabinet.
S1DR
x
1 RU D-ring cable retainer, 80mm (3.1" ) x 40mm (1.5"), bag of 8pcs, attaches
to S2BRK6/S2BRK12.
S2DR
x
2 RU D-ring cable retainer, 80mm (3.1") x 80mm (3.1"), bag of 8 pcs, attaches
to S2BRK6/S2BRK12.
S1LR
x
1 RU L-ring cable retainer, 60mm (2.2") x 100mm (3.8"), bag of 8pcs, attaches
to S2BRK6/S2BRK12.
S2LR
x
2 RU L-ring cable retainer, 85mm (3.4") x 100mm (3.8"), bag of 8pcs, attaches
to S2BRK6/S2BRK12.
Casters and Locks
NCSTR4
S2BRK6
x
SCSTR4
S1DR
S2DR
S1LR
S2LR
CCL3
NCSTR4
SCSTR4
CCL3
28
Caster Kit. 2 fixed casters for front of cabinet, 2 swivel casters for rear of cabinet,
4 mounting plates and 24 screws. Casters add 24mm (1") to height of cabinet.
S2BRK12
visit www.panduit.com/Cabinets
x
x
Caster Kit. 2 fixed casters for front of cabinet, 2 swivel casters for rear of cabinet,
and 16 screws. Casters add 24mm (1") to height of cabinet.
x
Three digit combination lock with key over ride for single hinge or split doors.
Net-Access™ Cabinet Accessories (continued)
Part Number
N-Type
S-Type
Compatible Compatible
Description
Vertical Blanking Panels
NVBP
NVBP
x
Vertical blanking panels with pass-through holes for 42 RU through 48 RU cabinets.
S6VBPN
x*
Vertical blanking panel for 600mm cabinets.
S7VBPN
x*
Vertical blanking panel for 700mm cabinets.
S8VBPN
x*
Vertical blanking panel for 800mm cabinets with 25mm (1") x 127mm (5") knock-outs.
Single and Dual Hinge Doors
N82SHDB
x
Single hinge door for 42 RU 800mm wide cabinet.
N85SHDB
x
Single hinge door for 45 RU 800mm wide cabinet.
N82DHDB
x
Dual hinge door for 42 RU 800mm wide cabinet.
N85DHDB
x
S62SHDB
S**SHDB
Dual hinge door for 45 RU 800mm wide cabinet.
x
Single hinge door for 42 RU 600mm wide cabinet.
S65SHDB
x
Single hinge door for 45 RU 600mm wide cabinet.
S72SHDB
x
Single hinge door for 42 RU 700mm wide cabinet.
S75SHDB
x
Single hinge door for 45 RU 700mm wide cabinet.
S82SHDB
x
Single hinge door for 42 RU 800mm wide cabinet.
S85SHDB
x
Single hinge door for 45 RU 800mm wide cabinet.
x
Split doors for 42 RU 600mm wide cabinet.
Split Doors
S62SDB
SN**SDB
S65SDB
x
Split doors for 45 RU 600mm wide cabinet.
S72SDB
x
Split doors for 42 RU 700mm wide cabinet.
S75SDB
x
Split doors for 45 RU 700mm wide cabinet.
SN82SDB
x
x
Split doors for 42 RU 800mm wide cabinet.
SN85SDB
x
x
Split doors for 45 RU 800mm wide cabinet.
* For use with S-Type switch configured cabinets.
visit www.panduit.com/Cabinets
29
Net-Access™ Cabinet Accessories (continued)
Part Number
N-Type
S-Type
Compatible Compatible
Description
Side Panels
N**SPS
N**SPH
S**SPSE
30
N21SPS
x
Split side panel for 42 RU 1070mm depth cabinet.
N51SPS
x
Split side panel for 45 RU 1070mm depth cabinet.
N81SPS
x
Split side panel for 48 RU 1070mm depth cabinet.
N22SPS
x
Split side panel for 42 RU 1200mm depth cabinet.
N52SPS
x
Split side panel for 45 RU 1200mm depth cabinet.
N82SPS
x
Split side panel for 48 RU 1200mm depth cabinet.
N21SPH
x
Split hinged side panel for end of row application for 42 RU 1070mm depth cabinet.
N51SPH
x
Split hinged side panel for end of row application for 45 RU 1070mm depth cabinet.
N81SPH
x
Split hinged side panel for end of row application for 48 RU 1070mm depth cabinet.
N22SPH
x
Split hinged side panel for end of row application for 42 RU 1200mm depth cabinet.
N52SPH
x
Split hinged side panel for end of row application for 45 RU 1200mm depth cabinet.
N82SPH
x
Split hinged side panel for end of row application for 48 RU 1200mm depth cabinet.
S21SPSE
x
S51SPSE
x
Split side panel for 45 RU 1070mm depth cabinet.
S81SPSE
x
Split side panel for 48 RU 1070mm depth cabinet.
Split side panel for 42 RU 1070mm depth cabinet.
S22SPSE
x
Split side panel for 42 RU 1200mm depth cabinet.
S52SPSE
x
Split side panel for 45 RU 1200mm depth cabinet.
S82SPSE
x
Split side panel for 48 RU 1200mm depth cabinet.
* For use with S-Type switch configured cabinets.
visit www.panduit.com/Cabinets
Net-Access™ Cabinet Accessories (continued)
Part Number
N-Type
S-Type
Compatible Compatible
Description
Integral Cabinet Top Cable Routing System
SN7TCDW
SN8TCDW
SN8TCDW
x
SN7TCDW
SN1070CREC
SN1200CREC
SN1200VCREC
x
Divider wall with screws for integral cabinet top cable routing system to enhance
cable management. For 800mm wide cabinet.
x
Divider wall with screws for integral cabinet top cable routing system to enhance
cable management. For 600mm and 700 mm wide cabinets.
SN1070CREC
x
x
End of row cap kit for integral cabinet top cable routing system. Includes brackets
and screws for 1070mm deep cabinet.
SN1200CREC
x
x
End of row cap kit for integral cabinet top cable routing system. Includes brackets
and screws for 1200mm deep cabinet.
SN1200VCREC
x
x
End of row cap kit for integral cabinet top cable routing system. Includes brackets
and screws for 1200mm deep VED cabinet.
RSHLF23
x
x
Shelf kit includes mounting bracket and screws. Shelf dimensions:
44mm (1.7")H x 483mm (19")W x 584mm (23")D. Load rating 275 lbs. (124kg).
RSHLF
x
x
Shelf kit includes mounting bracket and screws. Shelf dimensions:
44mm (1.7")H x 483mm (19")W x 762mm (30")D. Load rating 275 lbs. (124kg).
SN2RC
x
x
Cage nut rear rails for 42 RU cabinet, sold in pairs.
SN5RC
x
x
Cage nut rear rails for 45 RU cabinet, sold in pairs.
N2RT
x
N5RT
x
Shelves
RSHLF23
RSHLF
Equipment Rail Sets
SN*RC
Tapped (#12-24 ) rear rails for 42 RU cabinet, sold in pairs.
Tapped (#12-24 ) rear rails for 45 RU cabinet, sold in pairs.
S2RP
x
Vertical patching cage nut rails for 42 RU 600mm wide (0 RU QuickNet™) cabinet.
S5RP
x
Vertical patching cage nut rails for 45 RU 600mm wide (0 RU QuickNet™) cabinet.
Floor Seals
N2EOR1BA1070B1
x
N2EOR1CA1200B1
x
End of row floor seal for 1070mm deep cabinet.
End of row floor seal for 1200mm deep cabinet.
S2EOR1BA1070B1
x
End of row floor seal for 1070mm deep cabinet.
S2EOR1CA1200B1
x
End of row floor seal for 1200mm deep cabinet.
C2FAB06A1200B1
x
Front or back floor seal for 600mm wide cabinet.
C2FAB07A1200B1
x
Front or back floor seal for 700mm wide cabinet.
x
Front or back floor seal for 800mm wide cabinet.
C2FAB08A1200B1
x
N*RT
S*RP
visit www.panduit.com/Cabinets
31
Net-Direct™ In-Cabinet Ducting
CDE1
Part Number
CDE1
Net-Direct™ Air Inlet Duct, 1 RU that resides below the switch provides cold aisle airflow to Cisco^ 4948,
4928, and 4924. Optimized for use in server cabinet applications.
CDE2
Net-Direct™ Air Inlet Duct, 1 RU that resides in-line and below switch provides cold aisle airflow to
Cisco^ Nexus N2K-C2148T-1GE, N2K-C2248TP-1GE, and N2K-C2232PP-10GE fabric extenders and
Cisco^ WS-C4948E-F, WS-C4948E-F-S, and WS-C4948E-F-E. Optimized for use in server
cabinet applications.
CNLTD21B2
Net-Direct™ Air Inlet Duct designed for Cisco^ Catalyst 4900M switch. Consists of one 2 RU inlet duct
and a side duct.
CNLTD52A2
Net-Direct™ Air Inlet Duct designed for Cisco^ Catalyst 6504-E switch. Consists of 2 RU top and 2 RU
bottom inlet ducts and a side duct.
CNLTD142A3
Net-Direct™ Air Inlet Duct designed for Cisco^ Nexus 7009 switch. Consists of 3 RU top and 3 RU bottom
inlet ducts and a side duct.
CNLTD72A3
Net-Direct™ Air Inlet Duct designed for Cisco^ MDS 9506 switch. Consists of 3 RU top and 3 RU bottom
inlet ducts and a side duct.
CDE2
CNLTD21B2
CNLTD52A2
CNLTD142A3
Description
Inlet Ducts DIBBC2314S21W Net-Direct™ Air Inlet Duct designed for Cisco^ MDS 9513 switch. Consists of 2 RU top and 3 RU bottom
inlet ducts and a side duct.
DIRLC2214M21W Net-Direct™ Air Inlet Duct designed for Cisco^ Catalyst 6509-E switch. Consists of 2 RU top and 2 RU
bottom inlet ducts and a side duct.
CNLTD72A3
DIRBB2007S21W Net-Direct™ Air Inlet Duct designed for Cisco^ Nexus 7004 switch. Consists of one 2 RU inlet duct and
a side duct.
Exhaust Ducts
DERLCC6509A
Net-Direct™ Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 6509 switch.
DERLCC9513A
Net-Direct™ Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 9513 switch.
DERLCC7009A
Net-Direct™ Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 7009 switch.
DERLCC6513A
Net-Direct™ Air Exhaust Duct for Net-Access™ N-Type 1070mm Depth Cabinets.
Designed for Cisco^ 6513 switch.
DIBBC2314S21W
DIRLC2214M21W
^Cisco is a registered trademark of Cisco Technologies, Inc.
DIRBB2007S21W
Exhaust Ducts
32
visit www.panduit.com/Cabinets
Net-Direct™ In-Cabinet 7018 Ducting and 7018 Accessories
Part Number
Description
7018 Ducting Solution
DIEBCC7018B
DIRLD0425S27W
DIEBCC7018B
Net-Direct™ Air Inlet and Exhaust Ducting (blanking panels not included) designed for Cisco^ Nexus
7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet.
DIRLD0425S27W
Net-Direct™ Air Inlet Ducting with left and right side blanking panels for 42/48 RU cabinet designed for
Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet .
DIRLC7018VP51
Net-Direct™ Air Inlet Ducting with left and right side blanking panels for 51 RU cabinet designed for
Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet.
DIRLC7018VP4248 Net-Direct™ Air Inlet Ducting with right side only blanking panel for 42/48RU cabinet designed for
Cisco^ Nexus 7018 switch in a 1000mm wide Net-Access™ N-Type Cabinet .
7018 Cabinet Kits
N1000EXT
Extension kit to expand 800mm wide x 1200mm deep Net-Access™ N-Type Cabinet to 1000mm.
For use with cabinets N8229BS, N8529BS, and N8829BS.
7018 Vertical Blanking Panels
DIRLC7018VP51
NVBPA7018B
Vertical blanking panels with pass-through holes for 42 RU through 48 RU 1000mm wide cabinet.
N-Type Cabinet Split Doors
DIRLC7018VP4248
N2SD1000
One set of split doors (used front or back) for 1000mm wide Net-Access™ N-Type Cabinet 42 RU.
N5SD1000
One set of split doors (used front or back) for 1000mm wide Net-Access™ N-Type Cabinet 45 RU.
N8SD1000
One set of split doors (used front or back) for 1000mm wide Net-Access™ N-Type Cabinet 48 RU.
NVPDUB7018
Net-Access® N-Type PDU Bracket for 1000mm wide cabinets.
^Cisco is a registered trademark of Cisco Technologies, Inc.
N1000EXT
NVBPA7018B
NVPDUB7018
visit www.panduit.com/Cabinets
33
SmartZone™ Network-Enabled Rack PDUs North America
Part Number
P1L2B1L2N16BQA0
Description
For aggregate and per outlet power monitoring with switching, 30 A Single Phase, Horizontal Rack PDU, 208V, 12
IEC C-13 and 4 IEC C-19 locking receptacles, and NEMA L6-30P plug
P1T2B1L2N08ATA0
For aggregate and per outlet power monitoring, 30 A Single Phase Horizontal Rack PDU, 208V, 6 IEC C-13 and 2
IEC C-19 locking receptacles, and NEMA L6-30P plug.
Q1L1B1F0A24AFA0
For aggregate and per outlet power monitoring with switching, 20 A Single Phase Vertical Rack PDU, 208V, 18 IEC
C-13 and 6 IEC C-19 receptacles, and NEMA L6-20P plug.
Q1L2B1L2N24AFA0
For aggregate and per outlet power monitoring with switching, 30 A Single Phase Vertical Rack PDU, 208V, 18 IEC
C-13 and 6 IEC C-19 locking, and NEMA L6-30P plug.
Q1L2B1P3N24AFA0
For aggregate and per outlet power monitoring with switching, 30 A Three Phase Vertical Rack PDU, 208V, WYE,
18 IEC C-13 and 6 IEC C-19 locking receptacles, and NEMA L21-30P plug.
Q1L2B2G6N24AFA0
For aggregate and per outlet power monitoring with switching, 60 A Three Phase Vertical Rack PDU, 208V, Delta,
18 IEC C-13 and 6 IEC C-19 locking receptacles, and IEC 60309 - 9H 3P+E blue splash proof plug.
Q1N2B1L2N30AHA0
For aggregate power monitoring, 30 A Single Phase, Vertical Rack PDU, 208V, 24 IEC C-13 and 6 IEC C-19
locking receptacles, and NEMA L6-30P plug.
Q1N2B1N3N30AHA0
For aggregate power monitoring, 30 A Three Phase Vertical Rack PDU, 208 V, Delta, 24 IEC C-13 and 6 IEC C-19
receptacles, and NEMA L15-30P twist lock plug.
Q1N2B2W6N30AHA0 For aggregate power monitoring, 60 A Three Phase Vertical Rack PDU, 208V, Delta, 24 IEC C-13, 6 IEC C-19
receptacles, and IEC 60309-9H 3P+E plug.
34
Q1S2B2C3N24AFA0
For aggregate power monitoring with switching, 60 A Single Phase Vertical Rack PDU, 208V, 18 IEC C-13 and 6
IEC C-19 locking receptacles, and IEC 60309 - 9H blue splash proof plug.
Q1S2B2G6N24AFA0
For aggregate power monitoring with switching, 60 A Three Phase Vertical Rack PDU, 208V, Delta, 18 IEC C-13
and 6 IEC C-19 locking receptacles, and IEC 60309 - 9H 3P+E blue splash proof plug.
Q1S2B2T6N24AFA0
For aggregate power monitoring with switching, 50 A Three Phase Vertical Rack PDU, 208V, Delta, 18 IEC C-13
and 6 IEC C-19 locking receptacles, and NEMA CS-8365c plug.
Q1T2B2C3N24AFA0
For aggregate and per outlet power monitoring, 60 A Single Phase Vertical Rack PDU, 208V, 18 IEC C-13 and 6
IEC C-19 locking receptacles, and IEC 60309 -6H 2P+E plug.
visit www.panduit.com/Cabinets
SmartZone™ Network-Enabled Rack PDUs Global
Part Number
P1T1B3H0A08ATA0
Description
For aggregate and per outlet power monitoring, 16 A Single Phase Horizontal Rack PDU, 230V 6 IEC C-13 and 2
IEC C-19 locking receptacles, and IEC 60309-6H 2P+E plug.
Q1L2B2P6M24AFA0
For aggregate and per outlet power monitoring with switching, 32 A Three Phase Vertical Rack PDU, 230V/400V,
WYE 18 IEC C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 3P+N+E plug.
Q1L2B3J2M24AFA0
For aggregate and per outlet power monitoring with switching, 32 A Single Phase Vertical Rack PDU, 230V, 18 IEC
C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 2P+E plug.
Q1N1B3H0A30AHA0
For aggregate power monitoring, 16 A Single Phase Vertical Rack PDU, 230V, 24 IEC C-13 and 6 IEC C-19
receptacles, and IEC 60309-6H 2P+E plug.
Q1N2B2P6M30AHA0
For aggregate power monitoring, 32 A Three Phase Vertical Rack PDU, 230/400V, WYE, 24 IEC C-13 and 6 IEC
C-19 receptacles, and IEC 60309-6H 3P+N+E plug.
Q1N2B2Q0A30AHA0
For aggregate power monitoring, 16 A Three Phase Vertical Rack PDU, 230/400V, WYE, 24 IEC C-13 and 6 IEC
C-19 receptacles, and IEC 60309-6H 3P+N+E plug.
Q1N2B3J2M30AHA0
For aggregate power monitoring, 32 A Single Phase Vertical Rack PDU, 230V, 24 IEC C-13 and 6 IEC C-19
receptacles, and IEC 60309-6H 2P+E plug.
Q1S2B2P6M24AFA0
For aggregate power monitoring with switching, 32 A Three Phase Vertical Rack PDU, 230V/400, WYE, 18 IEC
C-13 and 6 IEC C-19 locking receptacles, and IEC 60309 -6H 3P+N+E plug.
Q1S2B2Q0A24AFA0
For aggregate power monitoring with switching, 16 A Three Phase Vertical Rack PDU, 230V/400V, WYE, 18 IEC
C-13 and 6 IEC C-19 locking receptacles, and IEC-60309-6H 3P+N+E plug.
Q1S2B3J2M24AFA0
For aggregate power monitoring with switching, 32 A Single Phase Vertical Rack PDU, 230V, WYE, 18 IEC C-13
and 6 IEC C-19 locking receptacles, and IEC 60309 -6H 2P+E plug.
Q1T1B3H0A24AFA0
For aggregate and per outlet power monitoring, 16 A Single Phase Vertical Rack PDU, 230V, WYE, 18 IEC C-13
and 6 IEC C-19 locking receptacles, and IEC 60309-6H 2P+E plug.
visit www.panduit.com/Cabinets
35
SmartZone™ Gateway-Enabled Rack PDUs North America
36
Part Number
GM-A0252BL
Description
For aggregate power monitoring, vertical, 30 A, single phase, 208V, 24 IEC C-13 and 6 IEC C-19 receptacles,
NEMA L6-30P plug, LCD display, with serial port for connection to Gateway.
GM-A0255BL
For aggregate power monitoring, vertical, 30 A, three phase, 208V, delta, 24 IEC C-13 and 6 IEC C-19 receptacles,
NEMA L15-30P plug, LCD display, with serial port for connection to Gateway.
GM-A0257BL
For aggregate power monitoring, vertical, 60 A, single phase, 208V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC
60309 - 6H 2P+E, LCD display, with serial port for connection to Gateway.
GMPO-A0276BL
For aggregate and per outlet power monitoring, horizontal 1 RU, 30 A, single phase, 208V, 6 IEC C-13 and 2 IEC
C-19 locking receptacles, NEMA L6-30P plug, LCD display, with serial port for connection to Gateway.
GMPO-A0277BL
For aggregate and per outlet power monitoring, vertical, 60 A, single phase, 208V, 18 IEC C-13 and 6 IEC C-19
receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.
GMS-A0280BL
For aggregate power monitoring with switching, vertical, 60 A, three phase, 208V, delta, 18 IEC C-13 and 6 IEC
C-19 locking receptacles, IEC 60309 - 6H 3P+E, LCD display, with serial port for connection to Gateway.
GMS-A0283BL
For aggregate power monitoring with switching, vertical, 60 A, single phase, 208V, 18 IEC C-13 and 6 IEC C-19
receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.
GMS-A0284BL
For aggregate power monitoring with switching, vertical, 50 A, three phase, 208V, delta, 18 IEC C-13 and 6 IEC
C-19 locking receptacles, NEMA CS-8365C plug, LCD display, with serial port for connection to Gateway.
GMSPO-A0286BL
For aggregate and per outlet power monitoring with switching, horizontal 1 RU, 30 A, single phase, 208V, 12 IEC
C-13 and 4 IEC C-19 locking receptacles, NEMA L6-30P plug, LCD display, with serial port for connection
to Gateway.
GMSPO-A0288BL
For aggregate and per outlet power monitoring with switching, vertical, 60 A three phase, 208V, delta, 18 IEC C-13
and 6 IEC C-19 locking receptacles, IEC-60309-9H 3P+E plug, with serial port for connection to Gateway.
GMSPO-A0289BL
For aggregate and per outlet power monitoring with switching, vertical, 30 A, three phase, 208V, WYE, 18 IEC C-13
and 6 IEC C-19 locking receptacles, NEMA L21-30P plug, with serial port for connection to Gateway.
GMSPO-A0291BL
For aggregate and per outlet power monitoring with switching, vertical, 30 A, single phase, 208V, 18 IEC C-13 and
6 IEC C-19 locking, NEMA L6-30P plug, with serial port for connection to Gateway.
GMSPO-A0292BL
For aggregate and per outlet power monitoring with switching, vertical, 20 A single phase, 208V, 18 IEC C-13 and
6 IEC C-19 receptacles, NEMA L6-20P plug, LCD display, with serial port for connection to Gateway.
visit www.panduit.com/Cabinets
SmartZone™ Gateway-Enabled Rack PDUs Global
Part Number
GM-A0258BL
Description
For aggregate power monitoring, vertical, 32 A, three phase, 230V/400V, WYE, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC 60309 - 6H 3P+N+E plug, LCD display, with serial port for connection to Gateway.
GM-A0259BL
For aggregate power monitoring, vertical, 16 A, three phase, 230/400V, WYE 24 IEC C-13 and 6 IEC C-19
receptacles, IEC 60309-6H 3P+N+E plug, LCD display, with Serial port for connection to Gateway.
GM-A0263BL
For aggregate power monitoring, vertical, 16 A, single phase, 230V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC
60309-6H 2P+E plug, LCD display, with Serial port for connection to Gateway.
GM-A0265BL
For aggregate power monitoring, vertical, 32 A, single phase, 230V, 24 IEC C-13 and 6 IEC C-19 receptacles, IEC
60309 - 6H 2P+E plug, LCD display, with Serial port for connection to Gateway.
GMPO-A0275BL
For aggregate and per outlet power monitoring, horizontal 1 RU, 16 A, single phase, 230V, 6 IEC C-13 and 2 IEC
C-19 locking receptacles, IEC 60309 - 6H 2P+E plug, LCD display, with serial port for connection to Gateway.
GMPO-A0278BL
For aggregate and per outlet power monitoring, vertical, 16 A, three phase, 230V, 18 IEC C-13 and 6 IEC C-19
locking receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.
GMS-A0281BL
For aggregate power monitoring with switching, vertical, 32 A, single phase, 230V, 18 IEC C-13 and 6 IEC C-19
locking receptacles, IEC 60309-6H 2P+E plug, LCD display, with serial port for connection to Gateway.
GMS-A0282BL
For aggregate power monitoring with switching, vertical, 16 A, three phase, 230V/400V, WYE 18 IEC C-13 and 6
IEC C-19 locking receptacles, IEC-60309-6H 3P+N+E plug, LCD display, with serial port for connection to Gateway.
GMS-A0285BL
For aggregate power monitoring with switching, vertical, 32 A, three phase, 230V/400, WYE 18 IEC C-13 and 6 IEC
C-19 locking receptacles, IEC 60309-6H 3P+N+E plug, LCD display, with serial port for connection to Gateway.
GMSPO-A0287BL
For aggregate and per outlet power monitoring with switching, vertical, 32 A, three phase, 230V/400V, WYE 18 IEC
C-13 and 6 IEC C-19 locking receptacles, IEC-60309-6H 3P+N+E plug, with serial port for connection to Gateway.
GMSPO-A0290BL
For aggregate and per outlet power monitoring with switching, vertical, 32 A, single phase, 230V, 18 IEC C-13 and
6 IEC C-19 locking receptacles, IEC-60309-6H 2P+E plug, with serial port for connection to Gateway.
visit www.panduit.com/Cabinets
37
SmartZone™ Sensors
ZEAIR-02
Part Number
ZEAIR-02
Airflow Sensor
Description
ZETHL-15
Humidity Sensor
ZEDIFFPRESS
01, 02, 03, 05 Differential Pressure Transducer
ZETHL-14
Temperature Sensor
ZEWS-03-03
Water Rope Sensor
ZETHL-15
ZEWS-03-03
38
visit www.panduit.com/Cabinets
SmartZone™ Sensors
ZEDIC05-01
ZESMA05-01
ZEDL05-01
ZETHL-11
ZEDL05-02
ZEPIR-04
Part Number
ZEDIC05-01
Description
Digital input sensor for use with voltage-free contacts
ZEDL05-01
Door sensor (micro switch type)
ZEDL05-02
Door contact sensor (magnetic type)
ZEPIR-04
PIR sensor
ZESMA05-01
Smoke detector
ZETHL-11
Combined temperature and humidity sensor
ZETHL-13
External temperature sensor
ZETHL-13
visit www.panduit.com/Cabinets
39
Blanking Panels and Blanking Shade
Part Number
TLBP1
TLBP2
TLBPBPT1S
Description
Tool-Less Blanking Panels
TLBP1S-V
19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed). 1 RU.
TLBP2S-V
19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed). 2 RU.
TLBP1R-V
19" (483mm) width for tapped rails. 1 RU.
TLBP2R-V
19" (483mm) width for tapped rails. 2 RU.
Pass-Through Blanking Panels
TLBPBPT1S
19" (483mm) width for 3/8" cage nut holes (may be used with or without cage nuts installed).
1 RU, with pass-through areas.
Blanking Shade
FLBSIMS
FLBSIMS
40
visit www.panduit.com/Cabinets
Full-length blanking shade blanks out 1-51 consecutive rack units on standard 19.00" (482.6mm) wide
vertical mounting rails; black.
Sealing Accessories
Part Number
CTGN1X5
Description
Cool Boot ® Cabinet Top Air Sealing Fitting
CTGN1X5
Used to seal off 1" x 5" cabinet top openings when cables are routed through the top of a cabinet. Airtight
fabric and Ultra-Cinch™ Tie close top of fabric, minimizing hot air bypass around cables to improve cooling
of network equipment and reduce energy costs. For use with 600mm wide Net-Access™ Cabinets.
CTGN3X5
Used to seal off 3" x 5" cabinet top openings when cables are routed through the top of a cabinet. Airtight
fabric and Ultra-Cinch™ Tie close top of fabric, minimizing hot air bypass around cables to improve cooling
of network equipment and reduce energy costs. For use with 700mm, 800mm, and 1000mm wide
Net-Access™ Cabinets.
CTGN6X6
Used to seal off 6.5" x 6.5" cabinet top openings when cables are routed through the top of a cabinet.
Airtight fabric and Ultra-Cinch™ Tie close top of fabric, minimizing hot air bypass around cables to improve
cooling of network equipment and reduce energy costs. For use with 600mm, 700mm, 800mm, and
1000mm wide Net-Access™ Cabinets.
CTGN3X5
CTGN6X6
Cabinet Top Cover and Cable Protection Bezel
CTCN1X5
CTCN1X5
Used to seal off 1.5" x 5" cabinet top openings. Can also be used to add the CTGN1X5 to openings where the
snap-on cover has been removed. For use with Net-Access™ Cabinets.
CTCN3X5
Used to seal off 3.5" x 5" cabinet top openings. Can also be used to add the CTGN3X5 to openings where the
snap-on cover has been removed. For use with Net-Access™ Cabinets.
CTNBZL6X6
Used to provide a protective edge for cables routed through the 6.5" x 6.5" cabinet top openings after
knock-outs are removed. Can also be used to add the CTGN6X6 to openings where knock-out has been
removed. For use with Net-Access™ Cabinets.
CTCN3X5
Blanking Foam Strips
BFS100X2000
CTNBZL6X6
Adhesive-backed blanking foam strips conform to minimize gaps and prevent bypass air within network
cabinets. Removable and repositionable acrylic-based adhesive is aggressive to provide suitable strength,
however, will not leave residue on equipment. 4.0" x 100" roll perforated 1.0" in width and 20.0" in length.
Cool Boot® Raised Floor Air Sealing Grommet
BFS100X2000
RFG12X4SMY
Overall size of 12" x 4" (304.8mm x 101.6mm) allows for 10.2" x 2.2" (259.1mm x 55.9mm) maximum capacity. Surface mount product can be installed over any opening less than 10.2” x 2.2” (259.1mm x 55.9mm).
RFG12X4Y
Overall size of 12" x 4" (304.8mm x 101.6mm) allows for 10.2" x 2.2" (259.1mm x 55.9mm) capacity.
Includes flexible sub-grommet to prevent damage to cable from sharp edges of cut floor tile.
RFG12X
visit www.panduit.com/Cabinets
41
Telecommunications Grounding Accessories
CNBK
Std.
Pkg.
Qty.
1
Part Number
CNBK
Description
Green bonding cage nut, includes 50 #12-24 bonding cage nuts (.06 – .11 thick panel) and
50 #12-24 x 1/2" bonding screws with #2 Phillips/slotted combo hex head (use 5/16" or 8mm socket).
RGCBNJ660P22
Mesh common bonding network (MCBN) jumper kit; #6 AWG (16mm2); 60" (1.52m) length; 45° bent
lug on grounding strip stide; provided with .16oz. (5cc) of antioxidant, two each #12-24 x 1/2", M6 x
12mm, #10-32 x 1/2" and M5 x 12mm thread-forming screws and a copper compression HTAP for
connecting to the SBG (MCBN) in sizes ranging from #6-#2 AWG (16 – 25mm2).
1
RGS1341Y
Rack grounding stip kit; 78.65" (2m) length; .67" (17mm) width; .05" (1.27mm) thickness; provided
with .16oz (5cc) of antioxidant, one grounding sticker, three each #12-24 x 1/2", M6 x 12mm,
#10-32 x 1/2" and M5 x 12mm thread-forming screws.
1
RGS134B-1
Cage nut grounding strip kit; 78.65" (2m) length; .67" (17mm) width; .05" (1.27mm) thickness;
provided with .16oz (5cc) of antioxidant, one grounding sticker, three cage nut bonding studs,
eight #12-24 bonding nuts and three stip clips.
1
RGS134B42-1
Equipment grounding strip kit, 42 RU, for cage nut mounting rails.
RGS134B48-1
Equipment grounding strip kit, 48 RU, for cage nut mounting rails.
RGESD2B-1
ESD port kit for cage nut rail fasteners: two-hole ESD port with 5/8" hole spacing, provided with an
ESD protection sticker, 16oz. (5cc) of antioxidant, two cage nut bonding studs and two #12-24
bonding nuts.
1
RGESDWS
Adjustable fabric ESD wrist strap with 6' coil cord, banana plug, 1 megohm resistor and 4mm snap.
1
RGRB19Y
Grounding busbar; 19" (483mm) length; tin-plated; fourteen holes arranged for flexibility in mounting;
provided with two each #12-24 x 1/2" and M6 x 12mm thread-forming screws.
1
RGRB19CN
Grounding busbar; 19" (483mm) length; tin-plated; twenty holes arranged for flexibility in mounting
with twenty #12-24 x 1/2" hex head screws installed; mounting hole sets have 5/8" (15.9mm) spacing;
provided with two cage nut bonding studs and four #12-24 bonding nuts.
1
RGCBNJ660P22
RGS134-1Y
RGESD2B-1
RGS134B42-1
RGS134B-1
RGS134B48-1
Refer to www.panduit.com/grounding for detailed information on the complete line of StructureGround™ Grounding Sytem products.
RGESDWS
RGRB19Y
RGRB19CN
42
visit www.panduit.com/Cabinets
Energy Efficient Data Center Cabinet System
A Part of Panduit’s Converged Infrastructure Solutions
Panduit Converged Infrastructure Solutions embody the next wave of systems integration and risk management by aligning and harmonizing
critical systems to support the delivery of secure, energy-efficient, always-on, real-time data and services. Energy Efficient Cabinet Systems
are one of the key pillars of the Panduit Converged Infrastructure Solutions portfolio that include:
Data Center Infrastructure Management (DCIM) — Panduit® SmartZone™ Solutions including hardware, software, and services that provide
end-to-end physical to logical view of your data center and extended enterprise. SmartZone™ Solutions enable effective optimization of your
data center’s space, power, and capacity planning through 10% OpEx savings in energy costs, 75% faster moves, adds, and changes (MACs),
and 80% faster mean time to repair (MTTR).
Data Center Advisory Services — Panduit Data Center Advisory Services provide a full range of physical infrastructure layer services
to help you assess, design, and maintain resilient, sustainable solutions that deliver operational flexibility to reduce costs by up to 20%,
and meet future requirements.
High Speed Data Transport (HSDT) Copper and Fiber Cabling Systems — Panduit HSDT Solutions are both protocol and media
agnostic, delivering maximum flexibility during planning, designing, commissioning, and operation of the data center. Our HSDT
Solutions enable advanced network architectures such as 10/40/100 Gig Ethernet LANs and 8/16/32 Gig Fibre Channel SANs and
can provide a 10% improvement in network throughput.
Converged Infrastructures — Panduit helps reduce deployment times up to 65% and mitigates the risk of adopting
new technologies with reliable and robust Converged Infrastructures. Panduit utilizes optimized reference designs collaboratively
engineered with our partners, to enhance the physical infrastructure of their technology platforms and seamlessly integrate physical
and logical systems.
Physical Infrastructure Foundation — Critical to the deployment of our Data Center solution is the physical infrastructure
foundation in the data center, which includes such items as:
Pathways: Provide the best method to route and manage the growing amount of data and power cabling while
ensuring high levels of network performance
Zone Cabling: Serves as a main distribution point for a particular zone, increasing network flexibility, manageability,
accessibility, and efficiency
Bonding and Grounding: Provides a high quality, visually verifiable and dedicated grounding path to maintain
system performance, improve network reliability, and protect network equipment and personnel
Identification and Labeling: Enhance the appearance of installations by presenting a clear and efficient way
to label according to TIA/EIA-606-A standards
visit www.panduit.com/Cabinets
43
Transform Your
Physical Infrastructure
Call or visit us online,
we can show you how.
Panduit Corp.
World Headquarters
Tinley Park, IL 60487
cs@panduit.com
US and Canada: 800.777.3300
Europe, Middle East, and Africa:
44.20.8601.7200
Latin America: 52.33.3777.6000
Asia Pacific: 65.6305.7575
©2016 Panduit Corp. ALL RIGHTS RESERVED. Printed in the U.S.A. RKCB37--SA-ENG Replaces RKCB30--SA-ENG
2/2016
www.panduit.com
Download PDF