quick start . guide - Gibbys Electronic Supermarket

Welcome to your new TV!
QUICK START
.
GUIDE
The following instructions cover assembling, connecting, and setting up your new TV. Make
sure you have the accessories listed below.
Included in this box
I
Remote Controls
~
e<mo"
Stand, Cables, Mounting Equipment
"~"
Batteries
(AAAx 2)
Stand
x3
Screws
lY
~
Power Cord
AC/DC Adapter
Make sure you have the correct cable before plugging it in. Illustrations of common plugs
and jacks are shown below.
Cable Plugs
HDMI'
USB
'
1111111111111111111111111111111111111111111
BN68-05018A-OO
--
Ports I Jacks
~~
~~
Do not plug cables in upside down.
Be sure to check the orientation of the
plug before plugging it in.
Warning
Step 7
Attach the TV to the Stand
Insert 3 screws and secure the stand to
the TV.
Lay the TV on a 'Soft surface, screen
side down. Use the packing material to
protect the screen.
"~
~
Holding the stand parallel to the screen,
slide the stand into the notches on the
back of the TV.
Step 2
Install the batteries into the remote
.. ..
Step 3
Connect Devices and Power Cable
We suggest using HDMI connections whenever possible for the best possible picture quality.
~
The position of the port may differ depending on the model.
Best Connection- HOM I
We suggest using HDMI
whenever possible.
HDMI1 is the default port
for a cable/satellite set top
box (STB).
Use the other ports for OVO
I Blu-ray, game consoles,
and other devices.
HDMICable
~
-
HDMI Port
Power Input
(Using an AC/DC
Adapter)
USB Connections
Antenna or direct-to-TV
cable connections
You can connect USB storage
devices to the USB jacks
and enjoy personal photos,
videos, and music.
Good Connection- COMPONENT
Use Component cable to connect Non-HDMI
devices to your TV. Match the colors on your
device's cables to the colors on the jacks.
Step 4
Lowest Quality Connection- AV
:.+E
;>~
Use an AudioNideo cable to connect NonHDMI devices to your TV.
Power on and begin guided setup
QT
~
Headphone
Connections
:r:c-
0
The stand is wobbly or crooked
Make sure the arrows on the stand are properly aligned.
The TV won't turn on
Make sure all cables are fully inserted, and that the remote has batteries installed.
(!) Power on to begin the guided setup.
Search channels from your TV
service provider
+
·1r
Troubleshooting
When you turn the TV on for the first time, a sequence of screens and on-screen
prompts will assist you in configuring the TV's basic settings. Plug the power cord into
a wall outlet, and then press the POWER button to turn on the TV. Configure your TV's
basic settings in the initial setup by following the instructions on your TV's screen.
1
!>
J
My remote doesn't work
The TV ships with protective stickers covering some of the sensors. Make sure all of the
stickers protective stickers have been removed.
~r
I don't know where to plug in <device>
Devices without HDMI may require the included AN adapter.
2
Set your local time zone
Central
Western
Eastern
Northen
Sou then
?
G
Congratulations on your new TV!
•
I have extra parts
The TV includes some optional parts to help with wall mounting and cable routing.
J_..;
u
-•
If you experience issues, please do not take the TV
back to the store. In the United States of America,
call us at 1-800-SAMSUNG (1-800-726-7864) or visit
us at www.samsung.com/spsn for support and
warranty service. For other countries, refer to "Contact
SAM SUNG WORLDWIDE" in the user guide.
•••
2. Important Safety Instructions
•••
1. Accessones and Cables
Accessories
The following accessories ""' included with your lV:
• Quick Start Guide
Input Cables (Sold Separately)
You will need one or more of theses cables to connect your lV to your antenna or cable outlet and your peripheral
devices (Biu-ray players, DVD players, etc.)
• CooiPonent
•HDMI
•HDMI·DVI
•Composite (A\/)
• Coaxial J!l.FJ.
~
Make sure you have the correct cable before plugging it in. Illustrations of common plugs and jacks are below.
Do not plug in opposite or wrong direction. It
coold damage the 1V port.
~
m
~
This sym.bol indicates that imjX)rtant literature
concerning operation and maintenance has
beerl1ncluded with this product.
- Do not cover the slots and openings with a cloth or other materials .
- Do not block the slots and openings by placing this apparatus on a bed, sofa, rug or other similar surface
- Do not place this apparatus in a confined space. such as a t:lool«:ase or built-in cabinet, unless proper ventilatiOn is provided.
• Do not place this apparatus near or over a radiator or heat register. or .....tlere ~ is exposed to direct Sl.Jnlig1t.
• Do not place a vessel coota.fling water (vases etc.) on this appwatus, as this can resut in a risk of lire or electric shock.
• Do not expose this apparatus to rain or place it near water (near a bathtub, washtloY.-1, kitchen sink, or ialn1'y tub, in a .......at basement, or near
a swimming pool etc.). If this app&"atus accidentally gets wet, lX"IpUg ~and cootact an authorized dealer immediately.
• ReQulatOIY Guide
•Audio
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER
ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage iS
present inside. tt is dangerous to make any kind
of cootact with any internal part of this product.
• The slots and openi"lgs in the cabinet and in the back or bottom are provided for necessary ventilatiOn. Toenstll3 reliable operatiOn of !his
apparatus, <nd to protect ~ from overhooting, these slots and openings must l"ll3'Yee" be blocked or covered.
• Stand Wire Holder ( N o t - for a1 ilches)
• Power Cold
• />C/OC Adapter )for 19', 22' models)
• Remote Control & Batteries r;v.A x 2)
• Owners Guide
&
• MakeSlXB to pU! out the power cord from the outlet before cleaning
• This apparatus use battenes. u-. yr::u: oomrriiJlily, there nitj1t be regulatiOns !hat require you to dispose of these batteries property to protect
the envronment. Please contact you lOCal authorities for disposal or~ informatiOn
• Do not OYerk>ad wall outlets, extension cords, or adaptors beyond their capacity, si"lce ltlisel:fi resuH in lire or electric sllock
• Power-supply COfds shotJd be routed so that tney are not likely to be waDied on or pinched by items placed ~or agailstthem. Pay
particular att!lf1tion to cords at the plug end, where comected to adaptors. CWld at the pol"lt where they exillrom the apparatus.
• To protect t~ apparatus from a ligltrWlg storm, or when it is left t.rl8ttended and ln.JSed for long periods of tme,l.f"IPlJg ~from the wall outlet
and disconnect the antenna or cable system. This .....-ill prevent damage to the set due to lightnilg and pcNI9f line surges.
• Before comecting the AC power cord to the DC adaptor outlet, make sure the YOitage designation of the DC adaptor conesp:Jnds to the lOCal
electrical supply. (depeoding on the m:xlel)
• Nwer insert~ metallic into the open parts oft~ apparatus. Ooi"'g so may create a danger of electric shock.
• To avoid electric shock. never touch the inside ol t~ apparatus. Only a qualified tect"nlcOO should open this appwatus.
• Make SlXB to plug the power cord in lXlt~ it is fm\ly inserted. Pul on the plug. not the cord, when removing the power cord from the outlet. Do
not touch the power cord with wet hands.
• If this apparatus does not operate normally - in particular, if there are 3lr"f tn.JSUal sounds or sme1s coming from ~ - l.f"IPlJ9 ~ immediately CWld
cootactanauthorizedclealerorservicecenter.
• Be SlXB to pull the power plug out of the outlet if the 1V is to remain I..OUSed or if you are to leave the house for an extended period of time
(espec:iatly when children, elderly or disabled people wil be left alone in the house).
USB
E-3
Opllc:al
~
- Accumulated dust can cause an electric shock. an electric leakage, or a fire by causing the power COI"d to generate sparks and heat.
or cause the insulatiOn to deteriorate.
• Be SlXB to cootact an authonzed service center, when i1stalng your set in a location with he<Ny dust. tij1 or low temperatures.l'igl h..r"r"Mdity,
~ Slbstances or where~ will operate for 24 hours a day such as nan airport, a train station, etc. Failure to do so may cause serious
damage to your set.
• Use only a property grounded plug and receptacle
- All improper ground may cause electric shock or equipment damage. (Class I Equipment only.)
• To tlrn off the apparatus c<>rrplet~. you must pull the
oo:::essibleataltinles.
power plug
out of the waD socket Consequently, the
power plug
should be readily
• Do not alow dlildren to hang onto the prockJct.
• Storetheaccessories(batteries,etc.)nalocationsafelyoutofthereactlofchildren.
• Do not instal the prockJct n an LfiStable location such as a shaky self. a slanted floor, or a location exposed to vibration.
• Do not drop or ~ a shock to the product. If the product is damaged, discomect the power cord CWld contact a serJ.ce center.
• To dem the product,ll"lplug the power cord from the power outlet and wipe the prockJct usng a soft cloth dipped in a small amot11l of water.
Do not use ant dlernicals such as waK, benzene, alcohol. thinners. ilsectieide, a~r freshener, ltbricant or detergent. This may damage the
Do not plug a cable in upside down.
Lt
Make sure the orientation of the plug is correct before plugging it in.
appearance or erase the printing on the product
~
• Do not expose the apparatus to dripping or splashing
• Oonotdisposeofbatteriesinafre.
• Do not short circ::Ut, disassemble, or overheat: the batteries.
1111111111111111111111111111111111111111111
• There is a danger of explosion if you replace the batteries with the wrong type of battery. Replace only with the same or eqt.ivalent type.
• WARNING - TO PREVENT THE SPREAD Of FIRE, KEEP CANDI.£8 OR OTHER OPEN FlAMES AWAY FROM THIS PROOLJCT AT ALL
TIMES.
BN68·04802A·OO
.2.
·1·
•••
3. Questions? Comments?
Contact SAMSUNG WORLDWIDE
If you have any questions or comments about your Samsung lY, please contact the SAMSUNG customer care center.
•••
5. The Remote Control
Learn where the function buttons are on your remote. Especially note POWER, SOURCE, VOL, CH, MENU, TOOLS,
ENTER, CH UST, RETURN, and EXIT.
~
This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually
impaired persons.
Samsung Electronics America, Inc.
85 Challenger Road
Press to access channels directly.
'N'NW.samsung.com
•••
4. Getting Started
Provide Ventilation for Your 1V
When you install your TV, maintain a distance of at least 4 inches between the lV and other objects (walls, cabinet sides,
etc.) to ensure proper ventilation. Failing to maintain proper ventilation may result in a fire or a problem with the product
caused by an increase in its internal temperature.
~
When using a stand or wall-mount, use parts provided by Samsung Electronics only.
~
Using parts provided by another manufacturer may cause difficulties with the product or result in injury caused by
Displays information on the TV
screeo.
the product falling.
~
Be careful when you contact the lV because some parts can be somewhat hot.
Exit the menu
Installation with a stand.
Installation with a wall-mount
.. --------·--T4iriche5---·---.
;--o·-------·
4inchOS-------.
D : D
4inches:
~
1
I
I
I
I
I
:
~4inches
4inches:
~
I
1
1
I
I
I
1
I
I
1
1
1
P.SIZE: Lets you choose the picture size.
MTS: Press to choose stereo. mono Of
Separate Audio Program (SAP broadcast).
CC:
c
,__.
··~
......
0
Controls the caption decoder.
:4inches
;f---I
I
I
I
I
I
Installing Batteries into the Remote (Battery size: AAA)
Match the polarity of the batteries to the symbols in the
batter compartment .
... NOTE
o
o
o
·3·
•
I~
;:";:
· Use these buttons in a specific
:____________ _L4~~~-------;
:
Use these buttons according to the
directions on screen.
Use the remote control within 23 feet of the TV.
Bright light may affect the performance of the remote
control. Avoid use when near fluorescent lights or neon
signs.
The color and shape of the remote may vary depending
on the model.
. 4.
feature.
•••
6. Making Connections
Connect your TV to an antenna or cable connection, and then connect your peripherals. When done, connect the power
cord to the TV, and then connect the power cord to an AC wall outlet. If you are connecting your TV to a cable or satellite
box using HDMI, Component, or Composite connections, you do not need to connect the ANT IN jack to an antenna or a
cable connection.
• FOf the best picture and audio quality, connect digital
devices using an HDMI cable.
UN32F4000 I UN32F4050 I UN32F5000 I UN32F5050 I
UN40F5000 I UN40F5050 I UN46F5000 I UN46F5050 I UN50F5000 I UN50F5050
~
The position of the port may differ depending on the model.
• PC/DVI AUDIO IN input is not supported.
• To connect an HDMI to DVI cable to the TV, you must
use the HDMIIN 2 (DVI) jack.
• If you connect an external de~ce to the 1V that uses
an older version of HDMI, the video and audio may not
work. If this occurs, ask the manufacturer of the device
about the HDMI version and, if it is out of date, request
an upgrade.
• For PCs with DVI video out jacks, use an HDMI to DVI
cable to connect the DVI out on the PC to the HDMIIN
2 (DVI) jack on the TV. Use the PC's speakers for audio.
• For a Set-top box connection using an HDMI cable, we
high~ recommend you connect the cable to the HDMI
IN 1 (STB) jack.
• Be sure to purchase a certified HDMI cable. Otherwise,
the picture may not display or a connection error may
occur.
I
HOM I connection J
Blu-rayplayeriDVDI
Set-top box
1
HDMI c:on~ec~
Set-top box I Blu-ray
PC coonection
(Using an HDMI (to DVI) Cable)
AV connection
VCR I Blu-ray player
Ill
••
I
playe</DVD
1!1
~
I
Ill
~
t
The position of the port may differ depending on the model.
[ Audio connection (DigitaO
Dig~al Audio System
=
1!1
UN19F4000 I UN22F5000 I UN28F4000 I UN28F4050
'
PC connection
I\JOI1g an HDMI (lo DVI) Cablel
1V Rear Panel
TV Rear Panel
[1
·------
Cabo
I Component connection I
~
~~
I Component connection I
Blu-ray player I DVD
••
AV connection
I
VCRIBiu-rayplayer
VHF/UHF Antenna
Cable
Blu-rayplayer/DVD
. 5.
7. Initial Setup
Ill
\oVhen you turn the TV on for the first time, a sequence
of screens and on-screen prompts will assist you in
configuring the TV's basic settings. After you plug the
power cord into a wall outlet, press the POWER button
to turn on the TV. Then, follow the instructions on the TV
screen to configure the TV's basic settings.
'
'
. 6.
To select a menu option in one of the categories, press the
..,_ button or the ENTER [!I button. Press it again or press
ENTER [31 to see the values or choices associated with
that option. Usually, you would then press ENTER [!I to
select a value or choice. Press the RETURN button or the
<1111 button to retum to a previous screen or selection.
10. Us1ng the TV's Controller (Panel Key)
Ill
If you are not using a cable box or satellite box, make
The TV's Controller, a small joy stick like button on the
sure you have connected the TV to an antenna or cable rear right side of the lv, lets you control the TV without
connection before you turn on the TV.
the remote control. To use the controller, push it forwards,
backwards, left, or right. To make a selection, press up.
To connect the power cord and antenna, refer to
Making Connections'.
·a.
8. Changing the Input Source
Ill
Select Media Play
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR
CORPORATION WITH RESPECT TO THIS PRODUCT SHAU. BE
BINDING Qt.l SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR
LOSS Of REVENUE OR PROfiTS, F.AJLURE TO REAIJZE SAVINGS
This SAMSUNG b'and product, as supplied and .distributed by SAMSUNG OR OTHER BENEF'TS, OR ANY OTHER SPECIAL, INCIDENTAL OR
end delivered new, i"' the origi'lal carton to the onginal const.mer p!XChaser, CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR
is warraflled by SAMSUNG agafist mcn.lfactll'i'lg defects i1 materials and INABIUTY TO USE THIS PRODUCT, REGI\RDLESS Of THE LEG.A.L
workmanship for a lirlited wai'TMty period of 00 Days Parts and Labor for THEORY ON \'VH!Oi Tl-lE CLAIM IS BASED, AND EVEN IF SAMSLING
Commercial Use
HAS BEEN ADVISED OF Tl-lE POSSIBILITY OF SUCH DAMAGES. NOR
SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN
·es
Cat
Parts L.abo'
Size
Service
AMOUNT THAN 11-E PURCHASE PRICE OF Tl-lE PRODUCT SOLD BY
40"
Carry-In or In
SAMSUNG AND CAUSING THE AllEGED DAMAGE. W1THOUT UMmNG
Tl-lE FOREGOING, PURCHASER ASSUMES AU. RISK AND UABIUTY
ard LNg..Home
1 Yea< 1 y,.,
37"
ard SmaiO<
Function menu
1. Press the SOURCE button on your remote.
2. Use the J;. / 'f buttons to select an external input source.
.lV I AV I Component I HDMI11 HDMI2/DVI
IL_ _jl-10
You can only choose external devices that are
connected to the TV. In the Source List, connected
inputs are highlighted.
Remote contrOl
How to Use Ed~ Name
~ensor J
; . c;·~·~;roller
The image is drawn
as if you are facing
the front of the 1V
Edit Name lets you associate a device name to an input
source. To access Edit Name, press the TOOLS button
when the Source List is displayed. Select the name of the
device connected to specific input jacks to make your input
source selection easier.
1 Yea< 1 y,.,
All
Project"'
IExcludi'\ILMll) ., 2Yea< 2Yea<
PICO& LED
Pocket Projector 1 Year I Yea<
All
Plasma[>spO,.
Select the Menu
When you are watching lV and you want to watch a movie
on your DVD player or Blu-ray player or switch to your
cable box or STB satellite receiver, you need to change the
Source.
All
FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCH/I.SER'S
Cany-ln
PAOPERTY AND TO OTHERS AND Tl-lEIR PROPERTY ARISING
OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODIJCT
SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE
OF SM1SUNG. THIS UMITED WAAIWITY SHALl. NOT EXTEND
TO ANYONE OTHER THAN Tl-lE ORIGINAL PURCH..4SER OF THIS
Carry-In orin
Home
Carry-In or
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXClUSNE
REMEDY
Pickup
Carry-In or
Pickup
'' 180 Days after Pt.rchasilg and 600 Hours of Use Lamp on Projector
This limited warranty begins on the original date of ptXchase, and is valid
only on products purchased and used il the t.JrVted States. To receive
warranty service, the p.xcllaser must cootact SAMSUNG for problem
determination and service procedtxeS. 'Warrat'lt'f service can only be
performed by a SAMSUNG authorized service center. The original dated
bl of sale must be p-esented UJXlll request as poof of p.xchase to
SAMSUNG or SAMSUNG's authorized service center.
SAMSUNGwil repair or replace !tis product, atOll'optionMdatno
charge as stp.Jiated herein, will1 new or reconditioned parts or prodt1.:1s if
found to be defective cMYlQ the lirl~ed warranty period specified above. AI
oeplaced parts and prod..cts become lhe property ol SAMSUNG and"'-"'
=~~~~.~~=~~s:the
"" If you connect a PC to the HDMIIN 2 (DVI) port with
an HDMI cable, assign PC to HDMI2 in Edit Name.
~
To close the Menu, Media Play List, or Source List,
press the Controller for more than 1 second.
'
When selecting a function by pushing the controller
forwards, backwards, left, right, be sure not to press
up on the controller before you reach your selection. If
you press up on the controller, it will stop operating in
the forwards, backwards, left, and right directions.
"" If you connect a PC to the HOM IIN 2 (DVI) port with
an HDMI to DVI cable, assign DVI PC to HDMI 2 in Edit
Name.
"" If you connect an AV device to the HDMIIN 2 (DVI)
port with an HDMI to DVI cable, assign DVI to HDMI2
in Edit Name.
9. Accessing and Using the Main Menu
SAMSUNG BRAND PRODUCTS
LIMITED WARRANTY TO ORIGINAL
PURCHASER
LCDII.EDTV
Source List
'
•• 1
11. Warranty Information
Ill
Your TV's Main menu contains functions that let you control
many of the TV's features. For example, in the Main menu
you can change the size and configuration of the picture, its
brightness, ~s contrast and so on. There are also functions
that let you control the TV's sound, channel configuration,
energy use, and a host of other features. To access the
main. on-screen menu, press the MENU (liD) button on
your remote.
Certan products are eligble for In-home servk::e atSa'nsung's discretion.
To receive i"'·home service, the prrxluct must be lX'IObstructed and
accessible to service personnel. If during i"'·home service, repai carnot
not be COIT'_IPieted, it may be~ to remove, repair and rettxn the
prodt1.:1. If 111-home serVICe IS t.naVailable, SAMSUNG may elect, atOll'
option: to~ for transportal~ of our choic:? to and from a SAMSUNG
authorized .S6fVK;e center. Otherwise, and for 37 .Mel~ l~D TV,
~~~1011 to Mel from the SAMSUNG authorized serVICe center IS the
;:rtyofthe~~ . del 1 . materialsWld
~wa;~~~ m:Si"' normal, ~ex~ ~o.,theextent otherwise
expressly provided for n t~ statement, noncommercial use of this
Pf(XIuct, am shal not apply to the folc:>wir9, ilck.dir9. but not nmited to:
damage wtVch occurs i"' shipment; deivery and ilstaRation; applications
and uses for which this product was not i"'lended; ahered product or
serial no..mbers; cosmetic damage or exterior li'lishes; accidents, abuse,
negiact, fie, water, igltning or other acts of nal\xe; use of products,
equipment, systems, utities, services, parts, supplies, accessories,
~lions, ilstallations, repairs, ext~ wffig or ~as not
•.
~or~by~NGwhi?h~thiSproduct.or
result n servce ~; incorrect ~ricalline voltage, .fluc.tuat~ and
~; cust~ adJUStments~ failure ~of~ operat1ng nstructiOnS,
clearung, ~~~and envronmental ns~ that are~
and pr~., the I'_'Struction book; ~1011 ~~diStortion
Some states do not allow limitations on how long a-~ fnplied waranty lasts,
or the excllsion or lfnilation of incidental or consequential damageS, so the
above limitations or exck.Jsions may not apply to you. This waranty gves
you specific legal riglts, and you may also have other rights wt"dl vary
from state to state. To obtain warranty service, please contact SAMSUNG
at·
Samsung Electronics America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660-2112
1-800-SAMSUNG (726 -7864)- www.samSUilQ.com
1-800-749-{1260: Projectors only
Important Warranty lnfonnation Regarding
IMPORTANT WARRANTY INFORMATION REGARDING
TELEVISION FORMAT VIEWING
Standard screen format televisions with aspect ratios of 4:3 (the
ratio of the screen width to screen height) are primarily designed
to display standard fonnat full-motion video.
The images displayed on them should primarily be in the standard 4:3
ratio format and be constantly moving. Displaying stationary graphics
and images on-screen, such as the dar1< top and bottom letterbox
bars (wide screen picttxeS), should be limned to no more than 15% of
the total television viewing per week.
Widescreenformattelevisionswithaspectratiosof16:9{the
rat~ of the ~reen width to screen hei!1ht) ~primarily designed
to d~splay w1~e screen fonnat full-mot~on ~Ideo .
The ·~ displayed on them should pnmanly be Wl the wide screen
16:9 rabo format, or expanded to fill the screen~ ycu model offers
this feature, and constantly moving. Displaying stationary graphics
and images on screen, such as the dar1< side-bars on non-expanded
standard format t9evision video and programming, should be lim~ed
to no more than 15% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock
market cra'Nis, video game displays, station logos, web sites or
computer graphics and patterns. should be lim~ed as desaibed
above for all televisions. Displaying arry stationary images that exceed
the above guidelines can cause uneven agflg of LED Display Panels
that leave subtle, but permanent burned-in ghost images in the
teie~Jisi?'l ~tlJ!B. To avoid this, vary.theprogramming~ images,
~!::!/~~~~;~~~~~~~mages.
=NGdoesnotwarrantlri'rt~tedoreour-freeoperationofthe ~=%!~~~~~~~t~!:~~ng
To use the Main menu, press the li. /T buttons to move
between the main option categories: Picture, Sound,
Channel, etc. Each time you press a J;. / 'f buttons, the
main category name on the left side of the menu changes.
THERE AAE NO EXPRESS WARRANTIES OTl-lER THAN THOSE
=~~~controls to view the different formats as a fuH
~~~&~~g~~r~NO~.f:j=E{0~ER
Be careful. in ~he selection ~d duration of television forma~s
used for VIGWing. Uneven ag11'1Q a~ B; result O! fonnat select100
and use, as well as other bumed-m 1mages, 1s not covered by
your Samsung limited warranty.
IMPIJED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
APARTICULAR PURPOSE SHALL APPLY AFTER Tl-lE EXPRESS
WARRANTY PERIODS STAl£D ABOVE, AND NO OTHER EXPRESS
. 7.
·8·
Getting Started
Warning! Important Safety Instructions
LED TV
Please read the safety instructions below before installing and using the product.
CAUTION
user manual
This symbol indicates that high voltage is
present inside. It is dangerous to make any kind
of contact with any internal part of this product.
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER
ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that important literature
concerning operation and maintenance has
been included with this product.
Connections
Accessories
y Remote Control (AA59-00600A) & Batteries (AAA x 2)
y Warranty Card / Regulatory Guide
y Owner’s Instructions
y Power Cord
y AC/DC Adapter (for 19", 22" models)
y Stand Wire Holder (BN61-08370A) (for 28", 29" models)
Input Cables (Sold Separately)
y Audio
y Composite (AV)
y Component
y Coaxial (RF)
y HDMI
y HDMI-DVI
y For the best picture and audio quality, connect digital devices using
an HDMI cable.
y If you connect an external device to the TV that uses an older version
of HDMI, the video and audio may not work. If this occurs, ask the
manufacturer of the device about the HDMI version and, if it is out of
date, request an upgrade.
y Be sure to purchase a certified HDMI cable. Otherwise, the picture
may not display or a connection error may occur.
y PC/DVI AUDIO IN input is not supported.
HDMI connection
✎
Make sure you have the correct cable before plugging it in. Illustrations of common plugs and jacks are shown below.
Set-top box / Blu-ray player / DVD
Still image warning
Important Warranty Information Regarding
Television Format Viewing
✎ Wide screen format LED Displays with aspect ratios of 16:9 (the ratio of the
screen width to screen height) are primarily designed to display wide screen
format full-motion video. The images displayed on them should primarily be in
the wide screen 16:9 ratio format, or expanded to fill the screen if your model
offers this feature and the images are constantly moving. Displaying stationary
graphics and images on screen, such as the dark sidebars on non- expanded
standard format television video and programming, should be limited to no
more than 5% of the total television viewing per week. Additionally, viewing
other stationary images and text such as stock market crawls, video game
displays, station logos, web sites or computer graphics and patterns, should
be limited as described above for all televisions. Displaying stationary images
that exceed the above guidelines can cause uneven aging of LED Displays
that leave subtle, but permanent burned-in ghost images in the LED picture.
To avoid this, vary the programming and images, and primarily display full
screen moving images, not stationary patterns or dark bars. On LED models
that offer picture sizing features, use these controls to view different formats
as a full screen picture. Be careful in the selection and duration of television
formats you use for viewing. Uneven LED aging as a result of format selection
and use, as well as burned-in images, are not covered by your Samsung
limited warranty.
y SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY
STATEMENT
Subject to the requirements, conditions, exclusions and limitations of the original
Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the
requirements, conditions, exclusions and limitations contained herein, SAMSUNG
will additionally provide Warranty Repair Service in the United States on SAMSUNG
products purchased in Canada, and in Canada on SAMSUNG products purchased
in the United States, for the warranty period originally specified, and to the Original
Purchaser only.
The above described warranty repairs must be performed by a SAMSUNG Authorized
Service Center. Along with this Statement and the Original Limited Warranty
Statement, a dated Bill of Sale as Proof of Purchase must be presented to the Service
Center. Transportation to and from the Service Center is the responsibility of the
purchaser. Conditions covered are limited only to manufacturing defects in material or
workmanship, and only those encountered in normal use of the product. Exclusions
include, but are not limited to, any originally specified provisions for in-home or
on-site services, minimum or maximum repair times, exchanges or replacements,
accessories, options, upgrades, or consumables.
For the location of a SAMSUNG Authorized Service Center, please call toll-free:
– In the United States : 1-800-SAMSUNG (1-800-726-7864)
– In Canada : 1-800-SAMSUNG
apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.
y Do not place this apparatus near or over a radiator or heat register, or where it is exposed to direct sunlight.
y Do not place a vessel containing water (vases etc.) on this apparatus, as this can result in a risk of fire or electric shock.
y Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near
TV Rear Panel
R
W
R
Y
R
W
Y
TV Side Panel
a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately.
Do not plug cables in upside down. Be sure to check the orientation
of the plug before plugging it in.
Power Input
(for 28", 29" models)
the environment. Please contact your local authorities for disposal or recycling information.
y Do not overload wall outlets, extension cords, or adaptors beyond their capacity, since this can result in fire or electric shock.
y Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords at the plug end, where connected to adaptors, and at the point where they exit from the apparatus.
TV Controller (Panel Key)
The TV’s Controller, a small joy stick like button on the rear left side of the TV, lets you control the TV without the remote control.
and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.
Selecting the Media Play
y Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local
electrical supply. (depending on the model)
✎
✎
y Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.
y To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
y Make sure to plug the power cord in until it is firmly inserted. Pull on the plug, not the cord, when removing the power cord from the outlet. Do
Installation with a wall-mount.
Function menu
4inches
4inches
USB
m R s
P
not touch the power cord with wet hands.
4inches
Power Input
(for 19", 22" models)
y To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet
✎
4inches
R-AUDIO-L
USB
y Make sure to pull out the power cord from the outlet before cleaning.
y This apparatus use batteries. In your community, there might be regulations that require you to dispose of these batteries properly to protect
Keep the required distances between the product and other objects (e.g. walls) to
ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in
the internal temperature of the product.
When using a stand or wall-mount, use parts provided by Samsung Electronics
only.
t If you use parts provided by another manufacturer, it may result in a problem
with the product or an injury due to the product falling.
The appearance may differ depending on the product.
Be careful when you contact the TV because some parts can be somewhat hot.
4inches
depending on the model.
VIDEO OUT
HDMI
- Do not cover the slots and openings with a cloth or other materials.
- Do not block the slots and openings by placing this apparatus on a bed, sofa, rug or other similar surface.
- Do not place this apparatus in a confined space, such as a bookcase or built-in cabinet, unless proper ventilation is provided.
Securing the Installation Space
Installation with a stand.
AUDIO OUT
y The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this
Avoid displaying still images (such as jpeg picture files) or still image elements (such
as TV channel logos, panorama or 4:3 image format, stock or news bars at screen
bottom etc.) on the screen. Constant displaying of still pictures can cause ghosting of
LED screen, which will affect image quality. To reduce risk of this effect, please follow
below recommendations:
y Avoid displaying the same TV channel for long periods.
y Always try to display any image on full screen, use TV set picture format menu for
best possible match.
y Reduce brightness and contrast values to minimum required to achieve desired
picture quality, exceeded values may speed up the burnout process.
y Frequently use all TV features designed to reduce image retention and screen
burnout, refer to proper user manual section for details.
y The position of the port may differ
VCR / Blu-ray player
DVI OUT
Do not plug in opposite or wrong direction. It could
damage the TV port.
Selecting a Source
(especially when children, elderly or disabled people will be left alone in the house).
Remote control sensor
- Accumulated dust can cause an electric shock, an electric leakage, or a fire by causing the power cord to generate sparks and heat,
or cause the insulation to deteriorate.
y Be sure to contact an authorized service center, when installing your set in a location with heavy dust, high or low temperatures, high humidity,
TV Controller
The image is drawn by facing
the front side of the TV.
y Use only a properly grounded plug and receptacle.
If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care center.
- An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
y To turn off the apparatus completely, you must pull the power plug out of the wall socket. Consequently, the power plug should be readily
accessible at all times.
y Do not allow children to hang onto the product.
Address
Customer Care
Center 1-800-SAMSUNG (726-7864)
Web Site
www.samsung.com/ca
(English)
www.samsung.com/ca_fr
(French)
R
B
G
R-AUDIO-L
y Store the accessories (batteries, etc.) in a location safely out of the reach of children.
y Do not install the product in an unstable location such as a shaky self, a slanted floor, or a location exposed to vibration.
y Do not drop or impart a shock to the product. If the product is damaged, disconnect the power cord and contact a service center.
y To clean the product, unplug the power cord from the power outlet and wipe the product using a soft cloth dipped in a small amount of water.
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. This may damage the
appearance or erase the printing on the product.
y Do not expose the apparatus to dripping or splashing.
PR
PB
Y
Headphones connection
Component connection
✎
✎
Exits the menu when pressing the controller more than 1 second.
When selecting the function by moving the controller to the up/down/left/right directions, be sure not to press the controller. If you press it first,
you cannot operate it to move the up/down/left/right directions.
Cable
How to use Edit Name
Changing the Input Source
Edit Name lets you associate a device name to an input source. To
access Edit Name, press the TOOLS button in Source List. Name the
device connected to the input jacks to make your input source selection
easier.
When connecting a PC to the HDMI IN 2(DVI) port with HDMI cable,
you should set the TV to PC mode under Edit Name.
✎ When connecting a PC to the HDMI IN 2(DVI) port with HDMI
to DVI cable, you should set the TV to DVI PC mode under Edit
Name.
✎ When connecting an AV devices to the HDMI IN 2(DVI) port with
HDMI to DVI cable, you should set the TV to DVI mode under Edit
Name.
Source List
Plug & Play (Initial Setup)
When you turn the TV on for the first time, a sequence of screens and on-screen prompts will assist you in configuring the TV’s basic settings. Press
the POWER button. Plug & Play is available only when the Input source is set to TV. Set the initial setup following instructions that the TV guides.
✎ Connecting the power cord and antenna. (refer to ‘Connections’)
y Do not dispose of batteries in a fire.
y Do not short circuit, disassemble, or overheat the batteries.
y There is a danger of explosion if you replace the batteries with the wrong type of battery. Replace only with the same or equivalent type.
y WARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL
www.samsung.com
ANT OUT
COMPONENT OUT
Blu-ray player / DVD
Contact SAMSUNG WORLDWIDE
Samsung Electronics
America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660
G
R
VHF/UHF Antenna
AUDIO OUT
Selecting the Menu
chemical substances or where it will operate for 24 hours a day such as in an airport, a train station, etc. Failure to do so may cause serious
damage to your set.
U.S.A
W
B
or
y Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time
CANADA
R
R
contact an authorized dealer or service center.
4inches
Samsung Electronics
Canada Inc.,
Customer Service
55 Standish Court
Mississauga
Ontario L5R 4B2 Canada
W
Return
y If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and
4inches
Country
R
Power Off
R
Figures and illustrations in this User Manual are provided for reference only and
may differ from actual product appearance. Product design and specifications
may be changed without notice.
Ports/Jacks
AV connection
PC connection
(Using an HDMI (to DVI) Cable)
HDMI OUT
Cable Plugs
y For an HDMI to DVI cable connection, you must use the HDMI IN
2 (DVI) port.
y Connecting through the HDMI cable may not be supported
depending on the PC.
y If an HDMI to DVI cable is connected to the HDMI IN 2 (DVI) port,
the audio does not work.
y For Set-top box connection using HDMI cable, we highly
recommend you to connect the HDMI IN 1 (STB) port.
✎
Use to select TV or an external input source such as a DVD player / Bluray player / cable box / STB satellite receiver.
1. Press the SOURCE button.
2. Select a desired external input source.
■ TV / AV / Component / HDMI1 / HDMI2/DVI
✎ You can only choose external devices that are connected to the TV.
In the Source List, connected inputs will be highlighted.
Information
You can see detailed information about the connected external device.
TIMES.
BN68-04797F-01
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
-1-
Remote Control
✎
-2-
■ Add / Delete: Delete or add a channel to display the channels you
want.
✎ All deleted channels will be shown on the All Channels menu.
✎ A gray-colored channel indicates the channel has been deleted.
✎ The Add menu only appears for deleted channels.
✎ Delete a channel from the Added Channels or Favorite menu in
the same manner.
■ Add to Favorite / Delete from Favorite t: Set channels you
watch frequently as Favorites.
■ Timer Viewing: You can set a desired channel to be displayed
automatically at the set time; even when you are watching another
channel. Set the current time first to use this function.
✎ Only memorized channels can be reserved.
✎ Reserved programs will be displayed in the Programmed menu.
✎ When a digital channel is selected, press the Ź (Next Program)
button to view the digital program. If you select the ENTERE
(Schedule) button on the next program, you can set Timer
Viewing directly.
■ Channel Name Edit: (analog channels only) Assign your own
channel name.
■ Select All: Select all the channels in the channel list.
■ Deselect All: Deselect all the selected channels.
✎ You can only select Deselect All when one or more channels
are selected.
■ Auto Program: Scans for a channel automatically and stores in the
TV.
Channel Menu
This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually impaired persons.
T Seeing Channels
Channel List
Displays and selects the available video
sources.
Turns the TV on and off.
Turns the remote control light on or off. When
on, the buttons become illuminated for a
moment when pressed. (Using the remote
control with this button set to On will reduce the
battery usage time.)
Press to directly access to channels.
Press to select additional channels (digital) being
broadcasted by the same station. For example, to
select channel ‘54-3’, press ‘54’, then press ‘-’ and ‘3’.
Returns to the previous channel.
Cuts off the sound temporarily.
Adjusts the volume.
Changes channels.
Displays the channel list on the screen.
Displays the main on-screen menu.
MEDIA.P
Views the Media Play.
SLEEP
Quickly select frequently used functions.
Automatically shuts off the TV at a preset time.
Displays information on the TV screen.
Selects the on-screen menu items and changes the
values seen on the menu.
Add, delete or set Favorite channels and use the program guide for
digital broadcasts. Select a channel in the All Channels, Added
Channels, Favorite or Programmed screen by pressing the Ÿź
buttons, and pressing the ENTERE button. Then you can watch the
selected channel.
■
All Channels: Shows all currently available channels.
■
Added Channels: Shows all added channels.
■ * Favorite: Shows all favorite channels.
■
Programmed: Shows all currently reserved programs.
✎ Using the remote control buttons with the Channel List
x Green (Zoom): Enlarges or shrinks a channel number.
x Yellow (Select): Selects multiple channel lists. Select desired
channels and press the Yellow button to set all the selected
channels at the same time. The c mark appears to the left of
the selected channels.
x T (Tools): Displays the Channel List option menu. (The Options
menus may differ depending on the situation.)
Channel Status Display icons
y c: A channel selected.
y * : A channel set as a Favorite.
y ) : A reserved program.
y ( : A program currently being broadcast.
Returns to the previous menu.
Exit the menu.
Antenna (Switch to Cable / Switch to Air t)
Use these buttons according to the direction
on screen.
Before your television can begin memorizing the available channels, you
must specify the type of signal source that is connected to the TV (i.e.
an Air or a Cable system).
Use these buttons in a specific feature.
✎
Display Modes (HDMI/DVI Input)
Installing batteries (Battery size: AAA)
Mode
Resolution
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H / V)
IBM
720 x 400
31.469
70.087
28.322
-/+
c
c
640 x 480
35
66.667
30.24
-/-
c
c
-/-
832 x 624
49.726
74.551
c
c
68.681
75.062
100
-/-
640 x 480
31.469
59.94
25.175
-/-
c
c
640 x 480
37.861
72.809
31.5
-/-
c
c
640 x 480
37.5
75
800 x 600
37.879
60.317
800 x 600
VESA DMT
1366 x 768 1920 x 1080
1152 x 870
800 x 600
48.077
46.875
72.188
75
31.5
-/-
c
c
40
+/+
c
c
50
+/+
c
c
49.5
+/+
c
c
1024 x 768
48.363
60.004
65
-/-
c
c
56.476
70.069
75
-/-
c
c
1024 x 768
60.023
75.029
78.75
+/+
c
c
c
c
c
c
1152 x 864
1280 x 720
1280 x 800
67.5
45
49.702
75
108
+/+
60
74.25
+/+
59.81
83.5
108
✎
c
75.025
135
+/+
47.712
59.79
85.5
+/+
+/+
1440 x 900
55.935
59.887
106.5
-/+
c
+/+
c
60
60
108
1680 x 1050
65.29
59.954
146.25
-/+
c
1920 x 1080
67.5
60
148.5
+/+
c
(analog channels only)
If the reception is clear, you do not have to fine tune the channel, as
this is done automatically during the search and store operation. If the
signal is weak or distorted, fine tune the channel manually.
✎ Fine tuned channels that have been saved are marked with an
asterisk “*” on the right-hand side of the channel number in the
channel banner.
✎ To reset the fine-tuning, select Reset.
How to Stop Auto Programming
Picture Menu
NOTE
t Use the remote control within 23 feet from TV.
t Bright light may affect the performance of the remote control.
Avoid use when nearby fluorescent lights or neon signs.
t The Color and shape may vary depending on the model.
Mode t
This function filters out scrambled channels after Auto Program is
completed. This process may take up to 20~30 minutes.
✎ Press the ENTERE button to stop the Clear Scrambled
Channel.
✎ This function is only available in Cable mode.
Select your preferred picture type.
When connecting a PC, you can only select Entertain and
Standard.
Dynamic: Suitable for a bright room.
Standard: Suitable for a normal environment.
Movie: Suitable for watching movies in a dark room.
Entertain: Suitable for watching movies and games.
✎ Only available when connecting a PC.
✎
Samsung MagicAngle
-4-
✎
for 19", 22" models
Adjust screen viewing Angle to optimize screen quality according to your
viewing position.
■ Samsung MagicAngle: When viewing the screen at an angle from
below or above by setting the appropriate mode for each position you
can obtain a similar picture quality as viewing the screen directly from
the front.
Off: Select when viewing from the front position.
Lean Back Mode: Select when viewing from a slightly lower position.
Standing Mode: Select when viewing from the upper position.
■ Mode: Adjust screen viewing angle.
✎ When Samsung MagicAngle is set to Lean Back Mode or
Standing Mode, Gamma is not available.
Do not watch in 4:3 format for a long time. Traces of borders
displayed on the left, right and center of the screen may cause
image retention (screen burn) which are not covered by the
warranty.
Screen Fit: (DTV) Displays the full image without any cut-off when
HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals
are inputted.
✎ HD (High Definition): 16:9 - 1080i/1080p (1920x1080), 720p
(1280x720)
✎ Settings can be adjusted and stored for each external device you
have connected to an input on the TV.
✎ Picture Sizes available by Input Source:
Backlight / Contrast / Brightness / Sharpness /
Color / Tint (G/R)
Input Source
Picture Size
ATV, AV, Component (480i, 480p)
16:9, Zoom1, Zoom2, 4:3
DTV(1080i, 1080p), Component
(1080i, 1080p), HDMI (720p, 1080i,
1080p)
16:9, Wide Fit, 4:3, Screen Fit
■ Digital Clean View: If the broadcast signal received by your TV is
weak, you can activate the Digital Clean View feature to reduce any
static and ghosting that may appear on the screen.
✎ When the signal is weak, try other options until the best picture
Advanced Settings
is displayed.
■ MPEG Noise Filter: Reduces MPEG noise to provide improved
(available in Standard / Movie mode)
picture quality.
Compared to previous models, new Samsung TVs have a more precise
■ HDMI Black Level: Selects the black level on the screen to adjust the
picture.
✎ When connecting a PC, you can only make changes to Gamma and screen depth.
✎ Available only in HDMI mode (RGB signals).
White Balance.
■ Film Mode: Sets the TV to automatically sense and process film
■ Dynamic Contrast: Adjusts the screen contrast.
signals from all sources and adjusts the picture for optimum quality.
■ Black Tone: Selects the black level to adjust the screen depth.
✎ Available in ATV, DTV(interlace), AV, COMPONENT (480i / 1080i)
■ Flesh Tone: Emphasize pink “flesh tone”.
and HDMI (480i / 1080i).
■ Color Space: Adjusts the range of colors available to create the
■ LED Clear Motion: Removes drag from fast scenes with a lot of
image.
movement to provide a clear picture.
■ White Balance: Adjusts the color temperature for a more natural
picture.
Picture Reset
R-Offset / G-Offset / B-Offset: Adjusts each color’s (red, green, blue)
Resets your current picture mode to its default settings.
darkness.
■ Reset Picture Mode: Returns all picture values in the currently
R-Gain / G-Gain / B-Gain: Adjusts each color’s (red, green, blue)
selected mode to the default settings.
brightness.
Your television has several setting options for picture quality control.
✎ When connecting a PC, you can only make changes to Backlight,
Contrast, Brightness and Sharpness.
Reset: Resets the White Balance to it’s default settings.
■ Gamma: Adjusts the primary color intensity.
■ Motion Lighting: Reduce power consumption by brightness control
adapted motion.
✎ Available in Standard mode only.
Picture Options
✎ When connecting a PC, you can only make changes to the Color
Tone, Size, and HDMI Black Level.
■ Color Tone
✎ Warm1 or Warm2 will be deactivated when the picture mode is
Dynamic.
■ Size: Your cable box/satellite receiver may have its own set of screen
sizes as well. However, we highly recommend you use 16:9 mode
most of the time.
16:9: Sets the picture to 16:9 wide mode.
Zoom1: Use for moderate magnification.
Zoom2: Use for a stronger magnification.
Wide Fit: Enlarges the aspect ratio of the picture to fit the entire
screen.
4:3: Sets the picture to basic (4:3) mode.
Sound Menu
Mode t
■
■
■
■
■
Standard: Selects the normal sound mode.
Music: Emphasizes music over voices.
Movie: Provides the best sound for movies.
Clear Voice: Emphasizes voices over other sounds.
Amplify: Increase the intensity of high-frequency sounds to allow a
better listening experience for the hearing impaired.
Equalizer
(standard sound mode only)
■ Balance L/R: Adjusts the balance between the right and left speaker.
■ 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment):
Adjusts the level of specific bandwidth frequencies.
■ Reset: Resets the equalizer to its default settings.
■
■
■
■
Channel List
O Channel List ĺ t
c
1600 x 900RB
Fine Tune
Channel List Option Menu
c
60.02
79.976
1366 x 768
Change the channel mode directly between Added Channels and
Favorite Channels.
The Favorite Channels is enabled only when you set Add to
Favorite.
✎
Clear Scrambled Channel
c
-/+
63.981
1280 x 1024
Channel Mode
STD, HRC and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable
system that exists in your particular area. At this point, the signal
source has been selected.
After all the available channels are stored, it starts to remove
scrambled channels. The Auto Program menu then reappears.
Press the ENTERE button to stop the channel store during Auto
Program.
T Other Features
c
1024 x 768
1280 x 1024
You can view, modify or delete a show you have reserved to watch.
■ Change Info: Change a show you have reserved to watch.
■ Cancel Schedules: Cancel a show you have reserved to watch.
■ Information: Display a show you have reserved to watch. (You can
also change the reservation Information.)
■ Select All / Deselect All: You can select or deselect all channels in
the channel list.
1. Press the ENTERE button.
2. A message will ask Stop Auto Program?. Select Yes by pressing
the Ż or Ź button.
3. Press the ENTERE button.
4 series:1366 x 768@60Hz / 5 series: 1920 x 1080@60Hz
57.284
O Channel List ĺProgrammed ĺt
Auto Program
✎ When selecting the Cable TV system: Selects the cable system.
✎
MAC
Programmed
(in Channel List)
T Memorizing channels
P.SIZE: Lets you choose the picture size.
MTS: Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
CC: Controls the caption decoder.
-3-
DTS TruSurround
(standard sound mode only)
DTS TruSurround is a patented DTS technology that solves the problem
of playing 5.1 multichannel content over two speakers. TruSurround
delivers a compelling, virtual surround sound experience through any
two-speaker playback system, including internal television speakers. It is
fully compatible with all multichannel formats.
Preferred Language
(analog channels only)
■ Mono: Choose for channels that are broadcasting in mono or if you
are having difficulty receiving a stereo signal.
■ Stereo: Choose for channels that are broadcasting in stereo.
■ SAP: Choose to listen to the Separate Audio Program, which is
usually a foreign-language translation.
✎ Depending on the program being broadcast, you can listen to
Mono, Stereo or SAP.
Auto Volume
Because each broadcasting station has its own signal conditions, the
volume may fluctuate each time channel is changed. This feature lets
you automatically adjust the volume of the desired channel by lowering
the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
Set the menu language.
✎ Choose between English, Español, and Français.
T Setting the Time
(digital channels only)
Digital-TV broadcasts are capable of simultaneous transmission of many
audio tracks (for example, simultaneous translations of the program into
foreign languages).
✎ You can only select a language from among the ones being
broadcasted.
Multi-Track Sound
Setup Menu
Language
Time
✎ The current time will appear every time you press the INFO button.
■ Clock: Setting the clock is for using various timer features of the TV.
✎ If you disconnect the power cord, you have to set the clock again.
Clock Mode: Set the current time manually or automatically.
Clock Set: Set the Month, Day, Year, Hour, Minute and am/pm.
✎ Available only when Clock Mode is set to Manual.
Time Zone: Select your time zone.
DST: (Daylight Saving Time) Switches the DST (Daylight Saving Time)
function on or off.
✎ DST and Time Zone function is only available when the Clock
Mode is set to Auto.
■ Sleep Timer t
Automatically shuts off the TV after a preset period of time. (30, 60,
90, 120, 150 and 180 minutes).
✎ To cancel the Sleep Timer, select Off.
Timer 1 / Timer 2 / Timer 3
Three different on / off timer settings can be made. You must set the
clock first.
■ On Time / Off Time: Set the hour, minute, am/pm and Activate /
Inactivate. (To activate the timer with the setting you have chosen, set
to Activate.)
Speaker Select
■ Volume: Set the desired volume level.
If you are listening to the sound track of a broadcast or movie through an ■ Contents: When the On Time is activated, you can turn on a specific
external receiver, you may hear a sound echo caused by the difference in
channel or play back contents such as photo or audio files.
decoding speed between the TV’s speakers and the speakers attached
í TV/USB: Select TV or USB. (Make sure that an USB device is
to your audio receiver. If this occurs, set the TV to External Speaker.
connected to your TV.)
✎ When you set Speaker Select to External Speaker, the TV’s
í Antenna: Displays the current antenna source.
speakers are turned off. You will hear sound through the external
í Channel: Select the desired channel.
speakers only. When you set Speaker Select to TV Speaker
í Music/Photo: Select the folder containing MP3/JPEG files on the
both the TV’s speakers and the external speakers are on. You will
USB device.
hear sound through both.
✎ The maximum displayed number of files, including sub folders, in
✎ When Speaker Select is set to External Speaker, the VOLUME
one folder of USB storage device is 2000.
and MUTE buttons will not operate and the sound settings will
✎ The media may not be playing smoothly when using the device
be limited.
lower than USB 2.0.
✎ If there is no video signal, both the TV’s speakers and the external
■ Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or
speakers will be mute.
Manual to set at you convenience. If you select Manual, you can set
Visual Impaired
up the day you want to activate the timer.
(digital channels only)
Adds verbal description to the main audio to help the visually impaired.
Sound Reset
■ Reset All: Resets all sound settings to the factory defaults.
T Other Features
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™,
you can enjoy a more realistic gaming experience by selecting the game
menu.
✎ Precautions and limitations for game mode
x To disconnect the game console and connect another external
device, set Game Mode to Off in the setup menu.
x If you display the TV menu in Game Mode, the screen shakes
slightly.
x Game Mode is not available when the input source is set to TV.
x After connecting the game console, set Game Mode to On.
Unfortunately, you may notice reduced picture quality.
Set each channel using the Channel List menu options. Option menu
items may differ depending on the channel status.
-5-
-6-
-7-
-8-
Program Rating Lock
Return to Default: This option sets each Size, Font Style, Foreground
Color, Background Color, Foreground Opacity and Background
The Program Rating Lock feature automatically locks out programs
Opacity to its default.
that are deemed inappropriate for children. The user must enter a PIN
✎ Digital Caption Options are available only when Default and
(personal identification number) before any of the Program Rating Lock
Service1~Service6 can be selected in Caption Mode.
restrictions are set up or changed.
✎ The Foreground and Background cannot be set to have the same
✎ Program Rating Lock is not available in HDMI or Component
color.
mode.
Melody
✎ The default PIN number of a new TV set is “0-0-0-0”.
■ Program Rating Lock: You can block rated TV Programs.
Set so that a melody plays when the TV is turned on or off.
■ TV Parental Guidelines: You can block TV programs depending on
✎
The Melody does not play.
their rating. This function allows you to control what your children are
x When no sound is output from the TV because the MUTE button
watching.
has been pressed.
■ MPAA Rating: You can block movies depending on their MPAA
x When no sound is output from the TV because the volume has
rating. The Motion Picture Association of America (MPAA) has
been reduced to minimum with the VOL – button.
implemented a rating system that provides parents or guardians with
x When the TV is turned off by Sleep Timer function.
advanced information on which films are appropriate for children.
■ Canadian English: You can block TV programs depending on their
Eco Solution
Anglophone Canadian.
■ Energy Saving: This adjust the brightness of the TV in order to
■ Canadian French: You can block TV programs depending on their
reduce power consumption. If you select Picture Off, the screen is
French Canadian rating.
turned off, but the sound remains on. Press any button except volume
■ Downloadable U.S. Rating: Parental restriction information can be
button to turn on the screen.
used while watching DTV channels.
■ Eco Sensor for 5 series : To enhance your power savings; the
■ Change PIN: The Change PIN screen will appear. Choose any 4 digits
picture settings will automatically adapt to the light in the room.
for your PIN and enter it in Enter New PIN. Re-enter the same 4 digits
✎ If you adjust the Backlight, the Eco Sensor will be set to Off.
in Confirm New PIN. When the Change PIN screen disappears, press
Min. Backlight: When Eco Sensor is On, the minimum screen
the OK button. The TV has memorized your new PIN.
brightness can be adjusted manually.
✎ If you forget the PIN, press the remote-control buttons in the
✎ If Eco Sensor is On, the display brightness may change (become
following sequence, which resets the pin to “0-0-0-0” : POWER
slightly darker in most cases) depending on the surrounding light
(off) ĺ MUTE ĺ 8 ĺ 2 ĺ 4 ĺ POWER (on)
intensity.
Caption
■ No Signal Power Off : Sets how quickly the TV switches to standby
mode, if no picture is being received.
(On-Screen Text Messages)
✎ Disabled when the PC is in power saving mode.
■ Caption: You can switch the caption function on or off. If captions are
■ Auto Power Off: The TV will be automatically turned off when no user
not available, they will not be displayed on the screen.
operation is received for 4 hours.
✎ The Caption feature does not work in Component or HDMI
mode.
Auto Protection Time
■ Caption Mode: You can select the desired caption mode.
If the screen remains idle with a still image for a certain period of
Default / CC1~CC4 / Text1~Text4: (analog channels only) The
time defined by the user, the screen saver is activated to prevent the
Analog Caption function operates in either analog TV channel mode
formation of ghost images on the screen.
or when a signal is supplied from an external device to the TV.
(Depending on the broadcasting signal, the Analog Caption function
may or may not work with digital channels.)
Support Menu
Default / Service1~Service6 / CC1~CC4 / Text1~Text4: (digital
channels only) The Digital Captions function works with digital
channels.
Self Diagnosis
✎ Service1~6 may not be available in digital caption mode
■ Picture Test: Use to check for picture problems. If the problem
depending on the broadcast.
continues to occur, check the color pattern.
■ Digital Caption Options: (digital channels only)
■ Sound Test: Use the built-in melody sound to check for sound
Size: Options include Default, Small, Standard and Large. The default
problems.
is Standard.
■ Signal Strength: (digital channels only) An HD channel’s reception
Font Style: Options include Default and Styles 0 to 7. The default is
quality is either perfect or the channels are unavailable. Adjust your
Style 0.
antenna to increase signal strength.
Foreground Color: Options include Default, White, Black, Red,
■ Reset: Reset all settings to the factory defaults.
Green, Blue, Yellow, Magenta and Cyan.
✎ The PIN input screen appears before the setup screen.
You can change the color of the letter. The default is White.
✎ Enter your 4-digit PIN. Change the PIN using the Change PIN
Background Color: Options include Default, White, Black, Red,
option.
Green, Blue, Yellow, Magenta and Cyan. You can change the
background color of the caption. The default is Black.
Software Upgrade
Foreground Opacity: This adjusts the opacity of text. Options include
Software Upgrade can be performed by downloading the latest
Default, Transparent, Translucent, Solid and Flashing.
firmware from samsung.com to a USB memory device.
Background Opacity: This adjusts the opacity of the caption
background. Options include Default, Transparent, Translucent, Solid
HD Connection Guide
and Flashing.
Refer to this information when connecting external devices to the TV.
x If a USB device connected to the TV is not recognized, the list of
Contact Samsung
View this information when your TV does not work properly or when you
want to upgrade the software. You can find information regarding our call
centers and how to download products and software.
x
Media Play
Enjoy photos, music and/or movie files saved on a
USB Mass Storage Class (MSC) device.
x
x
x
MEDIA.P
x
Connecting a USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music and/or movie files to
the USB jack on the side of the TV.
3. When USB is connected to the TV, you can select Media Play (USB)
in Applications menu.
T Using the Media Play Menu
1. Press the MENU button. Press the Ÿ or ź button to select
Applications, then press the ENTERE button.
2. Press the Ÿ or źbutton to select Media Play (USB), then press the
ENTERE button.
3. Press the Ż or Ź button to select an icon (Videos, Music, Photos,
Settings), then press the ENTERE button.
✎ It might not work properly with unlicensed multimedia files.
✎ Need-to-Know List before using Media Play (USB)
x Supported file systems are FAT and NTFS.
x Certain types of USB Digital camera and audio devices may not
be compatible with this TV.
x Media Play only supports USB Mass Storage Class (MSC)
devices. MSC is a Mass Storage Class Bulk-Only Transport
device. Examples of MSC are Thumb drives and Flash Card
Readers. Devices should be connected directly to the TV’s USB
port. USB HDD is not supported.
x Before connecting your device to the TV, please back up your files
to prevent them from damage or loss of data. SAMSUNG is not
responsible for any data file damage or data loss.
x A USB device that requires high power (more than 0.5A) may not
be supported.
x Do not disconnect the USB device while it is loading.
x The higher the resolution of the image, the longer it takes to
display on the screen.
x The maximum supported JPEG resolution is 15360 x 8640 pixels.
x If a file is corrupted or the TV does not support the file type, the
“Not Supported File Format” message appears.
x The TV cannot play MP3 files with DRM that have been
downloaded from a for-pay site. Digital Rights Management
(DRM) is a technology that supports the creation, distribution,
and management of digital content in an integrated and
comprehensive way, including protecting the rights and interests
of content providers, preventing illegal copying of contents, and
managing billings and settlements.
x PTP device is not supported.
x If an over-power warning message is displayed while you are
connecting or using a USB device, the device may not be
recognized or may malfunction.
x If the TV has no input during the time set in Auto Protection
Time, the Screensaver will run.
x The power-saving mode of some external hard disk drives may be
released automatically when your connect them to the TV.
x If you use a USB extension cable, the TV may not recognize the
USB device or may not be able to read the files on the device.
x
files on the device is corrupted, or a file in the list is not played,
connect the USB device to a PC, format the device, and check
the connection.
If a file you deleted from the PC is still found when you run Media
Play, use the “Empty the Recycle Bin” function on the PC to
permanently delete the file.
Photos only supports sequential jpeg format.
The scene search and thumbnail functions are not supported in
the Videos.
If the number of files and folders saved on a USB storage device is
approximately over 4000, the files and folders may not appear and
some folders may not be opened.
The maximum displayed number of files, including sub folders, in
one folder of USB storage device is 2000.
The media may not be playing smoothly when using the device
lower than USB 2.0.
Videos
1. Press the ŻŹ buttons to select Videos, then press the ENTERE
button in the Media Play menu.
2. Press the ŻŹŸź buttons to select the desired video in the file
list.
3. Press the ENTERE button or ˜ (Play) button.
- The selected file is displayed on the top with its playing time.
- If video time information is unknown, playing time and the progress
bar are not displayed.
- During video playback, you can search using the ŻŹ buttons.
✎ In this mode, you can play movie clips contained in a game, but you
cannot play the game itself.
y Supported Subtitle Formats
- External
Name
Troubleshooting
If the TV seems to have a problem, first review this list of possible problems and solutions. If none of these troubleshooting tips apply, visit samsung.
com, then click on Support, or call Samsung customer service at 1-800-SAMSUNG.
Problem
Possible Solution
Flickering and Dimming
If your Samsung Television is flickering or dimming sporadically, you may need to disable some of its energy efficient features
like the Eco Sensor or the Energy Saving feature. If you follow below step with your remote, you can turn these features
off or on.
y Energy Saving : MENU ĺ Setup ĺ Eco Solution ĺ Energy Saving
y Eco Sensor : MENU ĺ Setup ĺ Eco Solution ĺ Eco Sensor for 5 series
Component Connections /
Screen Color
Screen Brightness
Unwanted Powering off
Trouble Powering On
If you find that the color on your Samsung television’s screen is not correct or black and White, first run a Self Diagnosis on
the TV to make sure there are no device issues.
y Self Diagnosis : MENU ĺ Support ĺ Self Diagnosis ĺ Picture Test
If the test is ok, try making sure:
y Your connections are all consistent. For example, if you’ve used the AV In jack on your TV, make sure you have used the
AV Out jack on your video source.
y Try making sure you have connected to the correct jacks. For example, if you use the Component jacks, labeled Pb, Pr,
and Y, to connect your TV and video source, make sure you have connected the blue Pb jack on the video source to the
blue Pb jack on the TV, the red Pr jack on the source to the red Pr jack on the TV.
If you find that the colors on your Samsung TV are correct but just a little too dark or bright, there are some settings you
should check before calling for a repair.
y Backlight, Contrast, Brightness, Sharpness, Color, Tint (G/R) and so on. Go in to “Picture” on user Menu then try
adjusting options mentioned above.
If your Samsung TV appears to turn off by itself, there may be an issue with either your Timer settings or your Eco friendly No
Signal Power Off feature.
First make sure you Sleep Timer is not accidentally set. The sleep timer allows you the comfort of falling asleep with the TV
still on but, turns it off after a certain period of time so as not to waste energy.
y Sleep Timer : MENU ĺ Setup ĺ Time ĺ Sleep Timer
If the Sleep Timer is not activated, you may have engaged the No Signal Power Off or Auto Power Off feature.
y No Signal Power Off : MENU ĺ Setup ĺ Eco Solution ĺ No Signal Power Off
y Auto Power Off : MENU ĺ Setup ĺ Eco Solution ĺ Auto Power Off
Before Turn on check red light on the right or left bottom of your TV. Press power on button on TV or remote and it
will blink about 5 times before turning on.
If you find that you are having trouble powering on your Samsung television, there are a number of things to check before
making a call to the service department.
y If you happen to be using the TV as a monitor and the stand-by light only blinks for a few seconds when you press the
power button, your PC is in sleep mode. To take your PC out of sleep mode, press a key on your keyboard or move the
mouse. Then try turning your TV on.
If you’re sure your power cord, remote control, and PC are functioning properly, you may be having a cable issue. If you have
a cable or satellite box, your TV may appear to be off because the cable or satellite box is not outputting a signal. To test the
signal output of your cable or satellite box, press the guide or info button on the cable or satellite box remote control. If the
screen displays the guide or info data, the problem is caused by the box.
Stand Assembly
If you have any trouble to assemble the stand though you refer to “Install the Stand” mentioned at separate guide.
Cannot find channel
Re-run plug and play.
Poor picture
First, perform the Picture Test and to see if your TV is properly displaying the test image.
Go to MENU - Support - Self Diagnosis - Picture Test
If the test image is properly displayed, the poor picture may be caused by the source or signal.
The TV image does not look as good as it
did in the store.
If you have an analog cable/satellite box, upgrade to a digital set top box. Use HDMI or Component cables to deliver HD (high
definition) picture quality.
Cable/Satellite subscribers: Try HD channels from the channel line up.
Air/Cable Antenna connection: Try HD channels after performing Auto program.
Many HD channels are up scaled from SD(Standard Definition) contents.
y Adjust the Cable/Set top box video output resolution to 1080i or 720p.
Micro DVD
.sub or .txt
SubStation Alpha
.ssa
Advanced SubStation Alpha
.ass
Name
Container
Format
Xsub
AVI
Picture Format
SubStation Alpha
MKV
Text Format
Advanced SubStation Alpha
MKV
Text Format
SubRip
MKV
Text Format
MPEG-4 Timed text
MP4
Text Format
File
Extension Container Video Codec
ASF
Resolution
Frame
rate (fps)
Bit rate
(Mbps)
Divx3.11/4.x/
1920x1080
5.1/6.0
H264
1920x1080
AVC
"AVI
MKV"
1920x1080
MJPEG
640x480
Divx3.11/4.x/
1920x1080
5.1/6.0
MPEG4 SP/
1920x1080
ASP
H264
1920x1080
6~30
30Mbps
6~30
30Mbps
6~30
30Mbps
6~30
MP3 /
ADPCM /
AAC
10Mbps
6~30
30Mbps
6~30
30Mbps
6~30
Audio
Codec
30Mbps
MJPEG
Divx
3.11/4.x/
5.1/6.0
MPEG4 SP/
ASP
640x480
6~30
10Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
H.264
1920x1080
6~30
30Mbps
"MP3 /
AC3 /
LPCM /
ADPCM
/ DTS
Core"
"MP3 /
AC3 /
LPCM /
ADPCM
/ WMA
/ WMA
Pro"
6~30
30Mbps
"*.dat
*.mpg
*.mpeg
*.vob"
MPEG1
1920x1080
24/25/30
30Mbps
PS
MPEG2
H. 264 BP/
MP/HP
MPEG4 SP/
ASP
H.264
1920x1080
24/25/30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
*.3gp
3GPP
*.flv
flash
formats
H.264
Sorenson
H.263
Image
JPEG
x
x
x
Settings
Photo
Resolution
Base-line
15360 x 8704
Progressive
1024 x 768
y CMYK and YCCK Color space JPEGs are not supported.
Playing Multiple Files
MP3
MP3
the content or the container.
Sound or video may not work if the contents have a standard bit rate/
frame rate above the compatible Frame/sec listed in the table above.
If the Index Table is in error, the Seek (Jump) function is not supported.
The menu may take longer to appear if the video’s bit rate exceeds
10Mbps.
Video content can not be played, if there are many contents in one file.
■ Playing selected video/music/photo files
1. Press the Yellow button in the file list to select the desired file.
2. Repeat the above operation to select multiple files.
✎ NOTE
- The c mark appears to the left of the selected files.
- To cancel a selection, press the Yellow button again.
- To deselect all selected files, press the TOOLS button and select
Deselect All.
3. Press the TOOLS button, and then select Play Selected Contents.
■ Playing the video/music/photo file group
1. While a file list is displayed, move to any file in desired group.
2. Press the TOOLS button, and then select Play Folder.
Media Play - Additional Functions
■ Videos/Music/Photos Play Option menus
When playing a file, press the TOOLS button.
Video Decoder
Audio Decoder
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / MP /
AP L4 and AVCHD are not supported.
MPEG4 SP, ASP :
– Below 1280 x 720: 60 frame max
– Above 1280 x 720: 30 frame max
H.263 is not supported.
GMC is not support.
Supports up to WMA7, 8, 9
STD, 9 PRO, and 10 PRO
WMA 9 PRO and WMA 10 PRO
support 5.1 channel.
(LBR mode of WMA Pro is not
supported.)
WMA Lossless is not supported.
1. Press the ŻŹ buttons to select Music, then press the ENTERE
button in the Media Play menu.
2. Press the ŻŹŸź buttons to select the desired Music in the file
list.
(Play) button.
3. Press the ENTERE button or
✎ During music playback, you can search using the ŻŹ buttons.
✎
(REW) and
(FF) buttons do not function during play.
✎ Only displays the files with MP3 file extensions. Other file extensions
are not displayed, even if they are saved on the same USB device.
✎ If the sound is abnormal when playing MP3 files, adjust the
Equalizer in the Sound menu. (An over-modulated MP3 file may
cause a sound problem.)
Photos
1. Press the ŻŹ buttons to select Photos, then press the ENTERE
button in the Media Play menu.
2. Press the ŻŹŸź buttons to select the desired photo in the file
list.
(Play) button.
3. Press the ENTERE button or
✎ NOTE
- While a photo list is displayed, press the (Play) / ENTERE
button on the remote control to start the slide show.
- All files in the file list section will be displayed in the slide show.
- During the slide show, files are displayed in order.
- During the slide show, you can adjust the slide show speed using
(REW) or
(FF) button.
- You can move to other file using the ŻŹ buttons.
Videos
Music
Category
Operation
Title
You can move the other file
directly.
c
Repeat Mode
You can play movie and music files
repeatedly.
c
Picture Size
You can adjust the picture size to
your preference.
c
Picture Mode
You can adjust the picture setting.
c
Sound Mode
You can adjust the sound setting.
c
Subtitle Settings
You can play the video with
Subtitles. This function only works
if the subtitles are the same file
name as the video.
c
Audio Format
You can select the digital audio
output format.
c
Audio Language
You can change the audio
language if the video has more
than one language.
c
Stop Slide
Show /
Start Slide Show
You can start or stop a Slide Show.
c
Slide Show
Speed
You can select the slide show
speed during the slide show.
c
Background
Music
You can set and select
background music when watching
a Slide Show.
c
Zoom
You can zoom into images in full
screen mode.
c
Photos
Rotate
You can rotate images in full
screen mode.
c
Information
You can see detailed information
about the played file.
c
c
c
c
c
The wall mount kit (sold separately) allows you to mount the TV on the
wall.
For detailed information on installing the wall mount, see the instructions
provided with the wall mount items. Contact a technician for assistance
when installing the wall mount bracket. Samsung Electronics is not
responsible for any damage to the product or injury to yourself or others
if you elect to install the wall mount on your own.
Wall Mount Kit Specifications (VESA)
✎
The wall mount kit is not supplied, but sold separately.
Install your wall mount on a solid wall perpendicular to the floor. When
attaching to other building materials, please contact your nearest dealer.
If you install the TV on a ceiling or slanted wall, it may fall and result in
Kensington Lock
severe personal injury.
✎ NOTE
The Kensington Lock is not supplied by Samsung. It is a device used
to physically fix the system when using it in a public place. Refer to the
x Standard dimensions for wall mount kits are shown in the table
manual provided with the Kensington Lock for additional information on
below.
x When purchasing our wall mount kit, a detailed installation manual proper use.
and all parts necessary for assembly are provided.
✎ Please find a “K” icon on the rear of the TV. The Kensington slot is
beside the “K” icon.
x Do not use screws that do not comply with the VESA standard
screw specifications.
✎ The position and color may differ depending on the model.
x Do not use screws that are longer than the standard dimension
Assembling
the Stand Wire Holder
or do not comply with the VESA standard screw specifications.
Screws that are too long may cause damage to the inside of the
for 28", 29" models
TV set.
x For wall mounts that do not comply with the VESA standard screw
specifications, the length of the screws may differ depending on
the wall mount specifications.
x Do not fasten the screws too firmly. This may damage the product
or cause the product to fall, leading to personal injury. Samsung is
not liable for these kinds of accidents.
x Samsung is not liable for product damage or personal injury when
a non-VESA or non-specified wall mount is used or the consumer
fails to follow the product installation instructions.
Caution of the cover-jack
x Do not mount the TV at more than a 15 degree tilt.
x Always have two people mount the TV on a wall.
CAUTION: The cover-jack is for use by qualified service
personnel only. To reduce the risk of electric shock or fire
Product
TV size in
VESA screw hole specs (A
Standard
Quantity
Family
inches
* B) in millimeters
Screw
hazard, do not use the cover jack, unless you are qualified
to do so.
19~22
75 X 75
26-29
100 X 100
32-42
200 X 200
46~60
400 X 400
Remove the stand base from the TV and reassemble it.
The Channel menu is only available when you select the TV source.
There is no sound or the sound is too low at
maximum volume.
Please check the volume of the device (Cable/Sat Box, DVD, Blu-ray, etc.) connected to your TV.
Your settings are lost after 30 minutes or
every time the TV is turned off.
If TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. Please change from Store Demo
mode to Home Use mode using the Plug & Play procedure. Press the SOURCE button to select TV mode, go to MENU ĺ
Setup ĺ Plug & Play ĺ ENTERE.
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
The picture is good but there is no sound.
y If you are using an external device, check the device’s audio output option (ex. you may need to change your cable box’s
audio option to HDMI when you have a HDMI connected to your TV).
y Reboot the connected device by reconnecting the device’s power cable.
You have intermittent loss of audio or video.
Check the cable connections and reconnect them.
Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for long
term use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.
Display Resolution
The speakers are making an inappropriate
noise.
y Check the cable connections. Make sure a video cable is not connected to an audio input.
y For Antenna or Cable connections, check the signal information. A weak signal may cause sound distortion.
y Perform the Sound Test as explained above.
You see small particles when you look
closely at the edge of the frame of the TV.
This is part of the product’s design and is not a defect.
Screen Size
(Diagonal)
Select Home Use under Plug & Play mode. For details, refer to Plug & Play (Initial Setup).
Sound
Output
POP (TV’s internal banner ad) appears on
the screen.
The TV turns off automatically.
There is no picture/video.
y Make sure the AC power cord is securely plugged into the wall outlet and the TV.
y Make sure the wall outlet is working.
y Try pressing the POWER button on the TV to make sure the problem is not the remote.
If the TV turns on, refer to ‘Remote control does not work’ below.
y
y
y
y
Ensure the Sleep Timer is set to Off in the Time menu.
If your PC is connected to the TV, check your PC power settings.
Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
When you are watching TV connected to an antenna or cable connection, the TV will turn off after 10 - 15 minutes if there
is no signal.
y Check the cable connections. (Remove and reconnect all cables connected to the TV and external devices).
y Set your external device’s (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input. For
example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.
y Make sure your connected devices are powered on.
y Be sure to select the TV’s correct source by pressing the SOURCE button on the remote control.
y Reboot the connected device by reconnecting the device’s power cable.
✎
The TV is not receiving all channels.
y Make sure the coaxial cable is connected securely.
y Please try Auto Program to add available channels to the channel list.
go to MENU - Channel - Auto Program then select Auto and make sure the correct Cable TV signal type is set in the
menu. There are 3 options. (STD, HRC and IRC)
y Verify the antenna is positioned correctly.
No Caption on digital channels.
y Check the Caption Setup menu. Try changing Caption Mode Service1 to CC1.
y Some channels may not have caption data.
The picture is distorted: macroblock, error,
small block, dots, pixelization.
y Compression of video contents may cause picture distortion. Especially on fast moving pictures such as sports and action
movies.
y A weak signal can cause picture distortion. This is not a TV problem.
Others
Purple/green rolling horizontal bars and
buzzing noise from the TV speakers with
Component cable connection.
Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the set-top-box has
a grounding issue. Replace the Component video cables with an HDMI connection.
The picture is distorted: macroblock error,
small block, dots, pixelization.
y Compression of video contents may cause picture distortion, especially on fast moving pictures such as sports and action
movies.
y A weak signal can cause picture distortion. This is not a TV problem.
y Mobile phones used close to the TV (within 3.3ft) may cause noise in the picture on analog and digital channels.
The cable/set top box remote control
does not turn the TV on or off, or adjust
the volume.
Program the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box user manual for the
SAMSUNG TV code.
Color is wrong or missing.
If you’re using a component connection, make sure the component cables are connected to the correct jacks. Incorrect or
loose connections may cause color problems or a blank screen.
A “Mode Not Supported” message
appears.
Check the supported resolution of the TV and adjust the external device’s output resolution accordingly. Refer to resolution
settings in this manual.
There is poor color or brightness.
y Adjust the Picture options in the TV menu. (Go to Picture Mode / Color / Brightness / Sharpness)
y Adjust the Energy Saving option in the TV menu. (Go to MENU - Setup - Eco Solution - Energy Saving)
y Try resetting the picture to view the default picture setting. (Go to MENU - Picture - Picture Reset)
Caption on the TV menu is greyed out.
y You cannot select Caption in the TV menu when watching content from a device connected via HDMI or Component.
y Caption must be activated on the external device.
There is a plastic smell from the TV.
This smell is normal and will dissipate over time.
This function is only available for digital channels from an Antenna / RF / Coax connection.
This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce. However, there may be a few bright or
dark pixels on the screen. These pixels will have no impact on the performance of the product.
Watch these troubleshooting on video at www.samsung.com/spsn.
Some functions and pictures shown in this manual are available on specific models only.
You can keep your TV as optimum condition to upgrade the latest firmware on web site (samsung.com ĺ Support ĺ Downloads) by USB.
✎
✎
✎
Storage and Maintenance
✎ If you attached some stickers on the TV screen, it remains some debris after removing the sticker. Please clean it to watch TV.
✎ The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using a soft cloth to
prevent scratches.
Do not spray water directly onto the
product. Any liquid that goes into the
product may cause a failure, fire, or electric
shock.
RF(Cable/Antenna) Connection
Clean the product with a soft cloth
dampened with in a small amount of water.
Do not use a flammable liquid (e.g. benzene,
thinners) or a cleaning agent.
✎
Model Name
Dimensions (W x H x D)
Body
With stand
Weight
Without Stand
With Stand
✎
✎
✎
✎
✎
50°F to 104°F (10°C to 40°C)
10% to 80%, non-condensing
-4°F to 113°F (-20°C to 45°C)
5% to 95%, non-condensing
UN19F4000
UN22F5000
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under a license from U.S. Patent No’s:
5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616,
7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195,
7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol,
and DTS and the Symbol together are registered
trademarks & DTS Premium Sound is a trademark of
DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
Manufactured under a license from U.S. Patent No’s:
6,285,767, 8,027,477, 5,319,713, 5,333,201, 5,638,452,
5,771,295, 5,970,152, 5,912,976, 7,200,236, 7,492,907,
8,050,434, 7,720,240, 7,031,474, 7,907,736 and
7,764,802. DTS, the Symbol, and DTS and the Symbol
together are registered trademarks & DTS Studio Sound is
a trademark of DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
UN29F4000
1920 x 1080
1366 x 768
1366 x 768
22" Class
(21.5" measured diagonally)
28” Class
(27.5" measured diagonally)
29” Class
(28.5" measured diagonally)
17.8 X 11.2 X 1.9 inches
(453.7 X 285.8 X 49.5 (mm))
17.8 X 12.3 X 4.9 inches
(453.7 X 314.2 X 124.9 (mm))
20.2 X 12.6 X 1.7 inches
(513.1 X 321.5 X 43.8 (mm))
20.2 X 14.4 X 6.6 inches
(513.1 X 366.5 X 169.6 (mm))
25.3 X 15.3 X 1.9 inches
(645.0 X 389.4 X 49.5 (mm))
25.3 X 18.0 X 7.5 inches
(645.0 X 457.7 X 191.7 (mm))
26.3 X 15.5 X 1.9 inches
(668.6 X 394.7 X 49.5 (mm))
26.3 X 18.4 X 7.5 inches
(668.6 X 467.5 X 191.7 (mm))
5.5 lbs (2.5 kg)
5.7 lbs (2.6 kg)
5.7 lbs (2.6 kg)
6.3 lbs (2.9 kg)
9.2 lbs (4.2 kg)
10.3 lbs (4.7 kg)
9.4 lbs (4.3 kg)
10.5 lbs (4.8 kg)
3W x 2
5W x 2
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For information about your TV's power requirements and more about power consumption, refer to the label attached to the product.
Typical power consumption is measured according to Energy Star Program requirements for televisions.
Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/
recyclingdirect or call, (877) 278-0799.
To send inquiries and requests for questions regarding open sources, contact
Samsung via Email (oss.request@samsung.com).
„This product uses some software programs which are distributed under the
Independent JPEG Group.
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1995-2008 International Business Machines Corporation and others All
rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, and/or sell copies of the Software, and to permit persons to whom
the Software is furnished to do so, provided that the above copyright notice(s) and
this permission notice appear in all copies of the Software and that both the above
copyright notice(s) and this permission notice appear in supporting documentation.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE
COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE
FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES,
OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used
in advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
- 15 -
UN28F4000
1366 x 768
19" Class
(18.5" measured diagonally)
Open Source License Notice
Open Source used in this product can be found on the following webpage. (http://
opensource.samsung.com) Open Source License Notice is written only English.
DivX Certified® to play DivX® video up to HD 1080p,
including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX
video. Visit divx. com for more information and software tools to convert your files into
DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain
your registration code, locate the DivX VOD section in your device setup menu. Go
to vod. divx.com for more information on how to complete your registration. Covered
by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710;
7,519,274 DivX®, DivX Certified® and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under license.
The rear panel may differ depending on the model.
Specifications
License
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
- 14-
Cover-jack
- 12 -
The Channel menu is greyed out
(unavailable).
The TV will not turn on.
TV Rear Panel
4
M8
Do not install your Wall Mount Kit
while your TV is turned on. It may
result in personal injury due to
electric shock.
c
TV is tilted to the right or left side.
No Picture, No Video
M4
- 11 -
TV Signal Strength is unavailable in the
Self Diagnosis Test menu.
To prevent the TV from falling
Since the necessary clamps, screws, and string are not supplied,
please purchase these additionally.
1. Drive the screws into the clamps and firmly fasten them onto the wall.
Make sure the screws are firmly fixed into the wall.
2. Remove the screws from the back center of the TV, put the screws
into the clamps, and then fasten the screws onto the TV again.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the
wall with a strong cable and then tie the string tightly.
✎ Verify all connections are properly secured. Periodically check the
connections for any sign of fatigue or failure. If you have any doubt
about the security of your connections, contact a professional
installer.
✎ Install the TV close to the wall so that it does not fall.
✎ It is safe to connect the string so that the clamps fixed on the wall
are equal to or lower than the clamps fixed on the TV. Untie the
string before moving the TV.
✎
Other Information
Installing the Wall Mount Kit
LED-TV
c
Caution: Pulling, pushing, or climbing onto the TV may
cause the TV to fall. In particular, ensure that your children
do not hang over or destabilize the TV; doing so may cause
the TV to tip over, resulting in serious injuries or death.
Follow all safety precautions provided on the included
Safety Flyer. For added stability, install the anti-fall device for
safety purposes, as follows.
■ DivX® Video On Demand: Shows the registration code authorized
for the TV. If you connect to the DivX web site and register with
10-digit registration code, you can download the VOD activation file.
Once you play it using Media Play, the registration is completed.
✎ For more information on DivX® VOD, visit “http://vod.divx.com”.
■ Information: Select to view information on the connected device.
Other Restrictions
AC3 /
MPEG /
LPCM /
AAC
Securing the TV to the Wall
Using the Setup Menu
First of all, please perform the Sound Test to confirm that your TV audio is properly operating.
(Go to MENU - Support - Self Diagnosis - Sound Test)
If the audio is OK, the sound problem may caused by the source or signal.
y Replace the remote control batteries with correct polarity (+/–).
y Clean the transmission window located on the top of the remote control.
y Try pointing the remote directly at the TV from 5~6 feet away.
- 13 -
1920x1080
y Supported Photo Formats
y If connected to a cable box, please try to reset it. (Reconnect the AC cord and wait until the cable box reboots. It may take
up to 20 minutes)
y Set the output resolution of the cable box to 1080i or 720p.
y HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.
y Black bars on the Top & Bottom will be shown on movies that have aspect ratios different from your TV.
y Adjust the picture size option on your external device or change the TV to full screen.
If you are using an AV composite input, connect the video cable (yellow) to the Green jack of component input 1 on the TV.
H. 264 BP/
MP/HP
AC3 /
AAC /
MP3 /
DD+ /
HE-AAC
Sound Problem
The remote control does not work.
y If the picture size is set to Screen Fit, change it to 16:9.
y Change the cable/satellite box resolution.
30Mbps
When changing channels, the picture
freezes or is distorted or delayed.
The picture will not display in full screen.
The picture is black and white.
Audio
Codec
6~30
- 10 -
✎
There is a dotted line on the edge of the
screen.
Bit rate
(Mbps)
1920x1080
Music
y Supported Video Formats
"*.asf
*.wmv"
-9-
.srt
.sub
- Internal
"*.avi
*.mkv"
Frame
rate (fps)
MPEG2
TS
.smi
SubRip
SubViewer
MP4
x
.ttxt
SAMI
Resolution
"*.ts
*.trp
*.tp
*.m2ts"
Other Restrictions
x Video content will not play, or not play correctly, if there is an error in
File extension
MPEG-4 timed text
*.mp4
File
Extension Container Video Codec
- 16 -
LED TV
user manual
Wide screen format LED Displays with aspect ratios of 16:9 (the ratio of
the screen width to screen height) are primarily designed to display wide
screen format full-motion video. The images displayed on them should
primarily be in the wide screen 16:9 ratio format, or expanded to fill the
screen if your model offers this feature and the images are constantly
moving. Displaying stationary graphics and images on screen, such as
the dark sidebars on non- expanded standard format television video
and programming, should be limited to no more than 5% of the total
television viewing per week. Additionally, viewing other stationary images
and text such as stock market crawls, video game displays, station
logos, web sites or computer graphics and patterns, should be limited
as described above for all televisions. Displaying stationary images that
exceed the above guidelines can cause uneven aging of LED Displays
that leave subtle, but permanent burned-in ghost images in the LED
picture. To avoid this, vary the programming and images, and primarily
display full screen moving images, not stationary patterns or dark bars.
On LED models that offer picture sizing features, use these controls to
view different formats as a full screen picture. Be careful in the selection
and duration of television formats you use for viewing. Uneven LED aging
as a result of format selection and use, as well as burned-in images, are
not covered by your Samsung limited warranty.
y SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY
STATEMENT
Subject to the requirements, conditions, exclusions and limitations
of the original Limited Warranty supplied with Samsung Electronics
(SAMSUNG) products, and the requirements, conditions, exclusions and
limitations contained herein, SAMSUNG will additionally provide Warranty
Repair Service in the United States on SAMSUNG products purchased
in Canada, and in Canada on SAMSUNG products purchased in the
United States, for the warranty period originally specified, and to the
Original Purchaser only.
The above described warranty repairs must be performed by a
SAMSUNG Authorized Service Center. Along with this Statement and
the Original Limited Warranty Statement, a dated Bill of Sale as Proof
of Purchase must be presented to the Service Center. Transportation
to and from the Service Center is the responsibility of the purchaser.
Conditions covered are limited only to manufacturing defects in material
or workmanship, and only those encountered in normal use of the
product. Exclusions include, but are not limited to, any originally specified
provisions for in-home or on-site services, minimum or maximum repair
times, exchanges or replacements, accessories, options, upgrades, or
consumables.
For the location of a SAMSUNG Authorized Service Center, please call
toll-free:
– In the United States : 1-800-SAMSUNG (1-800-726-7864)
– In Canada : 1-800-SAMSUNG
Avoid displaying still images (such as jpeg picture files) or still image
elements (such as TV channel logos, TV shows or movies in panorama
or 4:3 format, stock or news scroll bars, etc.) on the screen. The
constant display of still pictures can cause ghosting or image burn-in
(image retention) on the LED screen, which will affect image quality. To
reduce the risk of this effect, please follow the recommendations below:
y Avoid displaying the same TV channel for long periods.
y Always try to display any image in full screen mode. Use the TV's
Picture Options menu to select the optimal screen size.
y Reduce brightness and contrast values to the minimum required to
achieve the desired picture quality. Values that exceed the minimum
may speed up the burn-in process.
y Frequently use all TV features designed to reduce image retention and
screen burn-in. Refer to proper user manual section for details.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care center.
Country
CANADA
U.S.A
Address
Samsung Electronics
Canada Inc.,
Customer Service
55 Standish Court
Mississauga
Ontario L5R 4B2 Canada
Samsung Electronics
America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660
Customer Care
Center 1-800-SAMSUNG (726-7864)
Web Site
www.samsung.com/ca
(English)
www.samsung.com/ca_fr
(French)
To add channels to the Added Channels list, follow these steps:
1. Select one or more channels in the All Channels list using the Ÿź
buttons and the Yellow (Select) button on your remote.
2. Press the TOOLS button on your remote. The Tools menu appears.
3. Select Add in the Tools menu, and then press the ENTERE button.
✎ All deleted channels are shown on the All Channels list. You add
channels back to the Added Channels list on the All Channels list.
✎ A gray-colored channel indicates the channel has been deleted from
the Added Channels list.
✎ The Add menu option only appears for deleted channels.
■ Add to Favorite /Delete from Favorite t: Lets you add
channels to and delete channels from your Favorites list.
To add channels to the Favorites list, follow these steps:
1. Select one or more channels in the All Channels list using the Ÿź
buttons and the Yellow (Select) button on your remote.
2. Press the TOOLS button on your remote. The Tools menu appears.
3. Select Add to Favorite in the Tools menu, and then press the
ENTERE button.
To delete channels from the Favorites list, follow these steps:
1. Select one or more channels in the Favorite Channels list using the
Ÿź buttons and the Yellow (Select) button on your remote.
2. Press the TOOLS button on your remote. The Tools menu appears.
3. Select Delete from Favorite in the Tools menu, and then press the
ENTERE button.
■ Timer Viewing: You can schedule a channel to be displayed
automatically at a set time, even when you are watching another
channel. You must set the current time first in the Time > Clock
function to use Time Viewing.
To schedule a channel, follow these steps:
1. Select a channel in the Added Channels list using the Ÿź buttons
and the Yellow (Select) button on your remote.
2. Press the TOOLS button on your remote. The Tools menu appears.
3. Select Time Viewing in the Tools menu, and then press the
ENTERE button. The Time Viewing screen appears.
Timer Viewing
Channel
Repeat
6-1
Once
Ÿ
ź
Date
Start Time
01-01-2013
L Move
U Adjust
12 : 01 am
E Enter
Picture Size
ATV, AV, Component (480i, 480p)
16:9, Zoom1,
Zoom2, 4:3
DTV (1080i, 1080p), Component (1080i,
1080p), HDMI (720p, 1080i, 1080p)
16:9, Wide Fit, 4:3,
Screen Fit
■ Digital Clean View: If the broadcast signal received by your TV is
weak, you can activate the Digital Clean View feature to reduce any
static and ghosting that may appear on the screen.
✎ When the signal is weak, try all the Digital Clean View options until
the TV displays the best picture.
■ MPEG Noise Filter: Reduces MPEG noise to provide improved
picture quality.
■ HDMI Black Level: For HDMI signals, select the black level to adjust
the screen depth. Low make blacks look darker.
✎ Available only in HDMI mode (RGB signals).
■ Film Mode: Sets the TV to automatically sense and process film
signals from all sources and adjusts the picture for optimum quality.
✎ Available in ATV, DTV (interlace), AV, COMPONENT (480i / 1080i)
and HDMI (480i / 1080i).
■ LED Clear Motion: Removes drag from fast scenes with a lot of
movement to provide a clear picture.
Picture Reset
Resets the picture settings to their factory defaults.
Sound Menu
Mode t
■
■
■
■
■
You can only select a language from among the ones being
broadcast.
Multi-Track Sound
Standard: Selects the normal sound mode.
Music: Emphasizes music over voices.
Movie: Provides the best sound for movies.
Clear Voice: Emphasizes voices over other sounds.
Amplify: Increase the intensity of high-frequency sounds to allow a
better listening experience for the hearing impaired.
Analog channels only.
■ Mono: Select for channels that are broadcasting in mono or if you are
having difficulty receiving a stereo signal.
■ Stereo: Select for channels that are broadcasting in stereo.
■ SAP: Select to listen to the Separate Audio Program, which is usually
a foreign-language translation.
✎ Depending on the program being broadcast, you can listen to
Mono, Stereo or SAP.
Auto Volume
Because each station has its own broadcasting conditions, the
volume may fluctuate each time you change the channel. This feature
automatically adjusts the volume of a channel by lowering the sound
output when the modulation signal is high or by raising the sound output
when the modulation signal is low.
SPDIF Output
for 32" and above models
The SPDIF (Sony Philips Digital InterFace) outputs an uncompressed
digital audio signal when you connect the digital audio jack on the back
of the TV to a digital audio in jack on a receiver or home theater.
■ Audio Format: You can select the Digital Audio output (SPDIF)
format. The available Digital Audio output format may differ depending
on the input source.
✎ By connecting the TV to a receiver or home theater with Dolby
Digital and 5.1ch speakers and selecting Dolby Digital, you can
maximize your interactive 3D sound experience.
■ Audio Delay: Lets you correct timing mismatches between the audio
track and the video when you are watching the TV and listening to
digital audio output from the TV through an external device such as
an AV receiver. When you select Audio Delay, a slider appears. Use
the left and right arrow buttons to adjust the slider. Press ENTERE
when done (0ms ~ 250ms).
Speaker Select
Equalizer
Available in Standard sound mode only.
■ Balance L/R: Adjusts the balance between the right and left speaker.
■ 100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment):
Adjusts the loudness of specific bandwidth frequencies.
■ Reset: Resets the equalizer to its default settings.
DTS TruSurround
Available in Standard sound mode only.
DTS TruSurround is a patented DTS technology that solves the problem
of playing 5.1 multichannel content through two speakers. TruSurround
delivers a compelling, virtual surround sound experience through any
two-speaker playback system, including internal television speakers. It is
fully compatible with all multichannel formats.
If you are listening to the sound track of a broadcast or movie through an
external receiver, you may hear a sound echo caused by the difference in
decoding speed between the TV’s speakers and the speakers attached
to your audio receiver. If this occurs, set the TV to External Speaker.
✎ When you set Speaker Select to External Speaker, the TV’s
speakers are turned off. You will hear sound through the external
speakers only. When you set Speaker Select to TV Speaker both
the TV’s speakers and the external speakers are on. You will hear
sound through both.
✎ When Speaker Select is set to External Speaker, the VOLUME
and MUTE buttons will not operate and the sound settings will be
limited.
✎ If there is no video signal, both the TV’s speakers and the external
speakers will be mute.
Visual Impaired
Digital channels only.
Adds verbal description to the main audio to help the visually impaired.
Sound Reset
Preferred Language
Resets all sound settings to the factory
Digital channels only.
defaults.
Channel
Menu
T Managing Channels
Channel List
T Memorizing Channels
If you are not using a cable box or satellite box, when you first set up
your TV using Plug & Play, the TV memorized the channels that were
available over the air or through your cable system and added them to
the Channel List. The Antenna and Auto program functions described
below let you re-run the channel memorization function without having to
re-run the Plug & Play procedure.
Antenna (Switch to Cable / Switch to Air t)
Before your television can memorize the available channels, you must
select your TV's signal source, Air (using an antenna) or Cable. Select
Menu > Channel > Antenna > Air or Cable. After you have selected the
signal source, go on to the Auto Program function.
✎ Selecting the signal source using the Antenna function also
determines the signal source the TV is tuned to. For example, if you
receive your TV signal over the air, and you select Cable, you will
see only snow. You must select Air to see a picture.
See your list of Added channels, Favorite channels, or channels you've
scheduled for viewing. Add or delete Favorite channels, add or delete
channels from the Added Channels list, schedule channels or programs
for viewing. Select a channel to watch on the All Channels, Added
Channels, or Favorite screen by pressing the Ÿź buttons, and then
pressing the ENTERE button.
✎ If you use a cable box or satellite box, you cannot use the Channel
List functions.
Auto Program
Air
The Auto Program function memorizes all channels that are available
over the air or through your cable system and adds them to the Channel
List.
✎ If your TV is connected to a cable box or satellite box, you do not
need to run Auto Program. You will use the tuner in the box, not the
tuner in the TV, to select channels.
To start Auto Program, follow these steps:
1. Push MENUm ĺ Channel ĺ Auto Program ĺ ENTERE on your
remote. The Antenna Source screen appears.
2. On the Antenna Source screen, select the source of your TV signal.
Air
If your TV is connected to an antenna choose Air, and then press
ENTERE. The TV will automatically start memorizing channels.
Cable
If your TV is connected to a cable outlet, choose Cable, and then
press ENTERE. Go to Step 3.
Auto
6
Air
Ɔ79
Ɔ79
8
Air
9
Air
Ɔ79
10
Air
Ɔ79
Ɔ79
' Zoom ' Select T7RROVŹ1H[W3URJUDP
Channel List Screens icons are listed on the left side. Select an
icon using the Ÿź buttons to view each list.
■
All Channels: Shows all currently available channels including
those you deleted from the Added Channels list.
Added Channels: Shows all Added Channels. These are the
channels that appear when you press the CH button.
■ * Favorite: Shows all favorite channels.
■
Programmed: Shows all channels and programs currently
scheduled using Timer Viewing.
✎ Remote control buttons active on the Channel List screen.
x Green (Zoom): Enlarges or shrinks a channel number.
x Yellow (Select): Move the cursor to a channel. Press the Yellow
button to select the channel. A c mark appears. Repeat to select
additional channels. Then, open the Tools menu and apply a
function to the channels you selected.
x T (Tools): Displays the Channel List Tools menu. (The Tools
menus may differ depending on the situation.)
x Ź (Next Program): Displays next programs.
■
Display Icons Used in the Channel List Screens
If you choose Auto, and then press ENTERE, the TV will
automatically select the correct Antenna source. Go to Step 3.
3. On the Cable Type screen, use the ŻŹŸź buttons to select the
type of digital and analog cable systems you have: STD, HRC, or
IRC. Most systems are STD (Standard). When done, select Start,
and then press ENTERE. The TV will start memorizing channels.
✎ Channel memorization can take up to 45 minutes, depending on
your cable system.
✎ Memorized channels are added to the Added Channels list. These
are the channels you will see when you use the Channel buttons on
your remote.
Icons
Meaning
c
A selected channel.
*
A Favorite channel.
)
A reserved program.
(
A program currently being broadcast.
T The Channel List Tools Menu
Clear Scrambled Channel
O
This function filters out scrambled channels after Auto Program is
completed. This process may take 20~30 minutes.
✎ Press the ENTERE button to stop Clear Scrambled Channel.
✎ This function is only available in Cable mode.
The Channel List Tools menu contains most of the functions you can use
on the All Channel, Added Channels, and Favorite List screens. To
view, select a list screen, select a channel, and then press the TOOLS
button.
■ Add / Delete: Delete a channel from or add a channel to the Added
Channels list.
Digital-TV broadcasts can transmit many audio tracks simultaneously (for
example, simultaneous translations of a program into foreign languages).
Channel List ĺ t
To delete channels from the Added Channels list, follow these steps:
1. Select one or more channels in the Added Channels list using the
Ÿź buttons and the Yellow (Select) button on your remote.
2. Press the TOOLS button on your remote. The Tools menu appears.
3. Select Delete in the Tools menu, and then press the ENTERE
button.
www.samsung.com
-1-
DTV Air
✎
You can adjust and store settings for each external device you have
connected to an input on the TV. Picture Sizes available by Input
Source are listed below:
Input Source
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
BN68-04801A-01
Antenna
✎
Added Channels
Still image warning
Figures and illustrations in this User Manual are provided for reference
only and may differ from actual product appearance. Product design and
specifications may be changed without notice.
Important Warranty Information Regarding
Television Format Viewing
✎ See the warranty card for more information on warranty terms.
■ Tint: Adjusts the amount of green and red in the picture. As you
The On Screen Menus
increase the amount of green, the amount of red decreases and vice
versa.
✎ When the TV is connected to a PC, you can only make changes to
Your TV has two kinds of menus, the Main menu and the various Tools
Backlight, Contrast, Brightness, and Sharpness.
menus. The Main menu gives you access to most or all of the menu
options available on your TV. The Tools menus display a selected number
Advanced
Settings
of frequently used menu options that change depending on the screen
you are viewing. A Tools menu symbol (T) in the lower right side of the
Available in Standard and Movie mode only.
screen indicates that a Tools menu is available.
Compared to previous models, new Samsung TVs offer a more precise
The Main menu has seven primary categories:
picture with more precise controls.
✎ When your TV is connected to a PC, you can only make changes to
y Picture
y Sound
y Channel
y Setup
Gamma and White Balance.
y Input
y Application
y Support
■ Dynamic Contrast: Adjusts the screen contrast.
To view the Main menu, press the MENU button on your remote. To view ■ Black Tone: Selects the black level to adjust the screen depth. Darker
settings make blacks look darker.
a Tools menu, press the TOOLS button on your remote.
■ Flesh Tone: Adjusts the amount of red in skin tones.
✎ The menu options that appear in the Main menu depend on the
■ Color Space: Auto automatically matches the range of colors (the
Source you have selected. For example, if you have selected the
variety and number of colors) available to create pictures with the
HDMI source, the Channel category will not appear. To see the
color range of the video source. Native provides a color range wider
Channel category, you must first select TV in the Source List.
than the color range of the video source.
The Menu options are presented below, arranged by Main menu
■ White Balance: Adjusts the color temperature of the picture so that
categories. A Tools button symbol (t) next to an option name
white objects look white (instead of, for example, slightly pink or
indicates the option is also available in one of the Tools menus.
slightly yellow) and the overall color of the picture looks natural.
R-Offset / G-Offset / B-Offset: Adjusts how dark each color (red,
green, blue) is.
Picture Menu
R-Gain / G-Gain / B-Gain: Adjusts how bright each color (red, green,
blue) is.
Mode t
Reset: Resets the White Balance to it’s default settings.
Select your preferred picture mode.
■ Gamma: Adjusts the primary color intensity.
✎ When your TV is connected to a PC, you can only select Entertain ■ Motion Lighting: When on, the TV automatically adjusts the
and Standard.
brightness of the screen in response to the brightness of the room. In
■ Dynamic: Brightens the screen. Suitable for a bright room.
bright light, the screen brightens. In dim light, the screen dims.
■ Standard: Suitable for a normal room brightness.
✎ Available in Standard mode only.
■ Movie: Darkens the screen, making it less glary. Suitable for watching
Picture Options
movies in a darkened room.
■ Entertain: Sharpens the picture. Suitable for games.
✎ When the TV is connected to a PC, you can only make changes to
✎ Only available when the TV is connected to a PC.
the Color Tone, Size, and HDMI Black Level.
■ Color Tone: Cool makes the picture bluer (cooler). Warm 1 and Warm
Samsung MagicAngle for 19", 22" models
2 make the picture redder (warmer).
Adjust screen viewing Angle to optimize screen quality according to your ✎ Warm1 and Warm2 are deactivated when the picture mode is set
viewing position.
to Dynamic.
■ Size: Set the size and aspect ratio of the picture on the screen. Your
■ Samsung MagicAngle: When viewing the screen at an angle from
cable box or satellite receiver may have its own set of screen sizes
below or above by setting the appropriate mode for each position you
as well. However, we highly recommend you use the TVs 16:9 mode
can obtain a similar picture quality as viewing the screen directly from
most of the time.
the front.
16:9: Sets the picture to the 16:9 wide screen format.
Off: Select when viewing from the front position.
Zoom1: Provides moderate magnification of the picture. Sides, top,
Lean Back Mode: Select when viewing from a slightly lower position.
and bottom are cut off.
Standing Mode: Select when viewing from the upper position.
Zoom2: Provides larger magnification of the picture. Sides, top, and
■ Mode: Adjust screen viewing angle.
bottom are cut off.
✎ When Samsung MagicAngle is set to Lean Back Mode or
Wide Fit: Enlarges the aspect ratio of the picture so the picture fits
Standing Mode, Gamma is not available.
the entire screen.
Backlight / Contrast / Brightness / Sharpness /
4:3: Sets the picture to the old, 4:3 format and puts black or gray
borders on the right and left of the picture.
Color / Tint (G/R)
✎
Do not watch your TV in the 4:3 format for a long time. Traces of
■ Backlight: Adjusts the brightness of the screen by adjusting the
borders displayed on the left, right and center of the screen may
brightness of the individual pixels.
cause image retention (screen burn) which is not covered by the
■ Contrast: Increases or decreases the contrast between dark and light
warranty.
areas of the picture.
Screen Fit: Displays the full image without any cut-off when your TV is
■ Brightness: Adjusts the brightness of the screen. Not as effective as
inputting HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p)
Backlight.
HD signals.
■ Sharpness: Sharpens or dulls the edges of objects.
✎ HD (High Definition) has a 16:9 aspect ratio and 1080i/1080p
(1920x1080) or 720p (1280x720) resolution.
■ Color: Adjusts the color saturation. The higher the Color setting, the
more intense the color. Low settings remove color and the picture
becomes black, white, and gray.
R Return
4. Use the ŻŹ buttons to move from entry field to entry field and the
Ÿź buttons to change the entries. Where numbers are displayed,
you can also enter numbers directly using the number keypad on
your remote.
-2-
✎
If you select Everyday or Every Week, the date you select in the
Date field becomes the start date for your scheduled viewing.
For Everyday, the TV will turn on every day, at the time you
selected, starting from that date. For Everyweek, the TV will turn
on every week, on the same day of the week as the start date
you selected, at the time you selected, from that day on. If you
select Once, the TV will turn on once, on the date and time you
selected.
5. Press the ENTERE button on your remote when done.
✎ Only Added Channels can be scheduled.
✎ Scheduled programs and channels are displayed in the
Programmed List.
✎ When you select a digital channel, press the Ź button to view the
digital program list. If you highlight a program in the list, and then
press the ENTERE (Schedule) button, you set Timer Viewing for
that program directly.
■ Channel Name Edit: Analog channels only. Lets you assign a name
of up to five characters to an analog channel. For example, Hist,
Food, Golf, etc. This makes it easier to find and select a channel.
■ Deselect All: Deselect all the selected displayed channels.
✎ You can only select Deselect All when one or more channels are
selected.
■ Select All: Select all the channels in the displayed channel list.
■ Auto Program: See Auto Program under Memorizing Channels.
■ Information: Display the information for a show or channel you have
scheduled. You can also change the schedule Information.
1. Select the Programmed List icon on the left side of the Channel
List screen, and then press the ENTERE button.
2. On the Programmed List screen, select the show or channel entry
you want information for, and then press the TOOLS button. The
Tools Menu appears.
3. Select Information, and then press the ENTERE button. The
Timer Viewing Info screen appears.
4. Select Change Info and press the ENTERE button to change
information, or select Close and press the ENTERE button to
close the Information screen.
■ Select All / Deselect All: You can select or deselect all channels in
the channel list.
Programmed List (on the Channel List Screen)
Analog channels only.
If the reception is clear, you do not have to fine tune the channel, as
this is done automatically during the search and store operation. If the
signal is weak or distorted, fine tune the channel manually.
✎ Select the channel, and then select Fine Tune.
✎ Fine tuned channels that have been saved are marked with an
asterisk “*” on the right-hand side of the channel number in the
channel banner.
✎ To reset fine-tuning, select the channel, select Fine Tune, and then
select Reset on the Fine Tune screen.
The Programmed list displays the channels and programs you have
scheduled for viewing using the Time Viewing function. You can view,
modify, or delete a show you have scheduled using the functions on the
Programmed List screen Tools menu.
Programmed List Screen Tools Menu
O
Channel List ĺProgrammed ĺt
■ Change Info: Change the scheduling information for a show or
channel you have scheduled.
To change the information, follow these steps:
1. Select the Programmed List icon on the left side of the Channel List
screen, and then press the ENTERE button.
2. On the Programmed List screen, select the show or channel entry
you want to change, and then press the TOOLS button. The Tools
Menu appears.
3. Select Change Info, and then press the ENTERE button. The
Time Viewing screen appears.
4. Use the ŻŹ buttons to move from entry field to entry field and the
Ÿź buttons to change the entries. Where numbers are displayed,
you can also enter numbers directly using the number keypad on
your remote.
Press the ENTERE button when done.
■ Cancel Schedules: Cancel a show or channel you have scheduled.
To cancel a scheduled show or channel, follow these steps:
1. Select the Programmed List icon on the left side of the Channel List
screen, and then press the ENTERE button.
2. On the Programmed List screen, select the show or channel entry
you want to cancel, and then press the TOOLS button. The Tools
Menu appears.
3. Select Cancel Schedules, and then press the ENTERE button.
The Cancel Schedule screen appears.
4. Select OK, and then press the ENTERE button.
-5-
-3-
To set the clock, follow these steps:
1. Select Setup >Time > Clock.
2. Press ENTERE and select Auto or Manual, and then press
ENTERE again.
If you selected Auto:
The TV will automatically download the correct time from a digital
channel.
y Select Time Zone, and then press the ENTERE button. Use
theŸź buttons to select your Time Zone, and then press
ENTERE.
y Select DST (Daylight Savings Time), and then press ENTERE.
Select On if you want to turn the DST adjustment on and off
manually. Select Off to turn off the DST adjustment. Select Auto if
you want the TV to adjust to DST automatically. Press ENTERE
when done.
✎ DST and Time Zone function are only available when the Clock
Mode is set to Auto.
T Other Channel Menu Functions
Channel Mode
Lets you select the channel list displayed when you press the <CH>
(Channel) button on your remote. For example, if you select Favorite
Channels, you will only see Favorite channels when you press the
<CH> button.
If you selected Manual:
The Clock Set screen appears. Use the Ÿź buttons to change the
values in each field or use the number buttons to enter the values
directly. Use the ŻŹ buttons to move from field to field. When done
with all the fields, press ENTERE.
✎ Available only when Clock Mode is set to Manual.
■ Sleep Timer t
Automatically shuts off the TV after a preset period of time. (30, 60,
90, 120, 150 and 180 minutes).
✎ To cancel the Sleep Timer, select Off.
Fine Tune
Timer 1 / Timer 2 / Timer 3
Turns the TV on and off automatically at times and days you select. You
can set three different on/off timer settings.
✎ You must set the clock first.
■ On Time / Off Time: Set the hour, minute, am/pm, and Activate/
Inactivate fields for On Time and Off Time. Use the ŻŹ buttons to
move from field to field. Use the Ÿź buttons to change the values
in each field. To activate the timer with the setting you have chosen,
set the Activate/Inactivate field to Activate.
■ Volume: Set the desired loudness.
■ Contents: To select what will be turned on when the timer setting is
activated. You can set the TV to turn on a specific channel or play
back contents such as photo or audio files. Use the ŻŹ buttons to
move to the Contents field, and then press the ENTERE button.
The Contents screen appears. Use the ŻŹ buttons to move from
field to field. Use the Ÿź buttons to change the values in each field.
- TV/USB: Select TV or USB. The USB device must be connected
to your TV before you can select USB.
- Antenna: Displays the current antenna source, Air or Cable.
- Channel: If you have selected TV, select the desired channel.
- Music/Photo: If you have selected USB, follow these steps to
select a folder containing MP3 (Music) or JPEG (Photo) files on the
USB device:
✎ The maximum number of files the TV can display, including sub
folders, in one folder of a USB storage device is 2000.
✎ The media may not play smoothly if you use a USB device rated
lower than USB 2.0.
1. Use the ŻŹ buttons to move to the field under Music or the
field under Photo, and then press the ENTERE button. The TV
displays a single folder (the Root folder) and the type or name of the
device.
Setup Menu
Plug & Play
Lets you re-run the Plug & Play initial setup procedure.
Language
Set the menu language.
✎ Choose between English, Español, and Français.
T Setting the Time
Time
✎ The time you set will appear when you press the INFO button.
■ Clock: Set the clock so you can use the various timer features of
the TV.
✎ If you disconnect the power cord, you have to set the clock again.
-6-
2. Press the ENTERE button. A list of folders on the device appears.
✎ If there are no folders on your device, press the Yellow (Select)
button to select the Root folder, and then press the RETURN
button. The Timer screen re-appears.
3. Use the Ÿź buttons to highlight a folder that contains music or
photos, and then press the Yellow (Select) button to select the folder.
4. Press the RETURN button. The Timer screen re-appears.
■ Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or
Manual. If you select Manual, you can select the days you want to
activate the timer by using the ŻŹ buttons to highlight the day, and
then pressing the ENTERE button. To unselect a day, highlight it,
and then press the ENTERE button.
When you are finished making all your selections on the Timer screen,
press either the ENTERE or RETURN button.
T Other Features
Game Mode
When you connect a game console such as a PlayStation™ or Xbox™
to your TV, you can enjoy a more realistic gaming experience by turning
on the Game Mode function.
✎ Precautions and limitations for game mode:
x Before you disconnect the game console and connect another
external device, set Game Mode to Off in the setup menu.
x If you display the TV menu in Game Mode, the screen shakes
slightly.
x Game Mode is not available when the input source is set to TV.
x After connecting the game console, set Game Mode to On. You
may notice slightly reduced picture quality.
■ Canadian English: You can block TV programs based on their
Anglophone Canadian ratings.
■ Canadian French: You can block TV programs based on their French
Canadian ratings.
■ Downloadable U.S. Rating: You can use parental restriction
information while watching DTV channels.
Locking/Blocking Programs or Movies
You lock or block programs and/or movies in essentially the same way
for each option. Each option displays a grid or table. All the tables have
ratings listed on the left. The TV Parental Guidelines option also has
kinds of content listed across the top: ALL: Lock all TV ratings. / FV:
Fantasy violence / V: Violence / S: Sexual situation / L: Adult Language /
D: Sexually Suggestive Dialog.
To lock/block movies or shows with certain ratings and/or kinds of
content, click the square next to the rating and/or under the kind of
content. A lock appears. To unlock/unblock, click the square again.
When you click a low rating, all the ratings above it will also display locks.
You can also Allow All or Lock All. When done, press the RETURN
button on your remote.
■ Change PIN: The Change PIN screen will appear. Choose any 4
digits for your PIN and enter them in Enter New PIN fields. Re-enter
the same 4 digits in Confirm New PIN fields. When the Change PIN
screen disappears, press the OK button. The TV has memorized your
new PIN.
✎ If you forget the PIN, press the remote-control buttons in the
following sequence, which resets the pin to “0-0-0-0” : POWER (off)
ĺ MUTE ĺ 8 ĺ 2 ĺ 4 ĺ POWER (on)
Caption
(On-Screen Text Dialogue)
Program Rating Lock
The Program Rating Lock feature lets you block programs you've
determined are inappropriate for your children based on the program's
ratings. To access the Program Rating Lock feature and make any
changes, you must enter a PIN (personal identification number). To
watch a blocked program, you must also enter the same PIN.
✎ Program Rating Lock is not available in HDMI or Component
mode.
✎ The default PIN number of a new TV set is “0-0-0-0”. You can set
your own PIN using the Change PIN function.
How It Works
When you access the Program Rating Lock Menu functions for the
first time, the PIN input screen appears. Enter 0-0-0-0. The PIN screen
closes and the Program Rating Lock Menu appears. Every time you
access the Program Rating Lock functions, the PIN screen will appear
and you must enter a PIN.
When the Program Rating Lock screen appears, select Program
Rating Lock, and then press ENTERE. Select On, and then press the
ENTERE key again. Depending on what type of programs or movies
you want to block, select one of the options on the screen, and then
press the ENTERE button. The options are listed below:
■ TV Parental Guidelines: You can block TV programs based on their
ratings. This function allows you to control what your children are
watching.
■ MPAA Rating: You can block movies based on their MPAA ratings.
The Motion Picture Association of America (MPAA) has implemented
a rating system that provides parents or guardians with advanced
information on which films are appropriate for children.
■ Caption: You can switch the caption function on or off. If captions are
not available, they will not be displayed on the screen.
✎ The Caption feature does not work in Component or HDMI mode.
■ Caption Mode: You can select the desired caption mode.
Default / CC1~CC4 / Text1~Text4: (analog channels only) The
Analog Caption function operates in either analog TV channel mode
or when a signal is supplied from an external device to the TV.
(Depending on the broadcasting signal, the Analog Caption function
may or may not work with digital channels.)
Default / Service1~Service6 / CC1~CC4 / Text1~Text4: (Digital
channels only) The Digital Captions function works with digital
channels.
✎ Service1~6 may not be available in digital caption mode depending
on the broadcast.
■ Digital Caption Options: (Digital channels only)
Size: Options include Default, Small, Standard and Large. The default
is Standard.
Font Style: Options include Default and Styles 0 to 7. The default is
Style 0.
Foreground Color: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan. You can change the color of
the letters. The default is White.
-7-
-4-
Background Color: Options include Default, White, Black, Red,
Green, Blue, Yellow, Magenta and Cyan. You can change the
background color of the captions. The default is Black.
Foreground Opacity: This adjusts the opacity of text. Options include
Default, Transparent, Translucent, Solid and Flashing.
Background Opacity: This adjusts the opacity of the caption
background. Options include Default, Transparent, Translucent, Solid
and Flashing.
Return to Default: This option sets each Size, Font Style, Foreground
Color, Background Color, Foreground Opacity and Background
Opacity to its default.
✎ Digital Caption Options are available only when you can select
Default and Service1 ~ Service6 in Caption Mode.
✎ The Foreground and Background cannot be set to the same color.
Melody
Set so that a melody plays when the TV is turned on or off.
✎ The Melody does not play:
x When no sound is output from the TV because the MUTE button
has been pressed.
x When no sound is output from the TV because the volume has
been reduced to minimum with the VOL – button.
x When the TV is turned off by Sleep Timer function.
■ Reset: Reset all settings to the factory defaults.
✎ The PIN input screen appears before the setup screen.
✎ Enter your 4-digit PIN. Change the PIN using the Change PIN
option.
Software Upgrade
Software Upgrade can be performed by downloading the latest
firmware from samsung.com to a USB memory device.
HD Connection Guide
Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when you
want to upgrade the software. You can find information regarding our call
centers and how to download products and software.
Media Play
Enjoy photos, music and/or movie files saved on a
USB Mass Storage Class (MSC) device.
MEDIA.P
Eco Solution
■ Energy Saving : Lets you adjust the brightness of the TV to reduce
power consumption. If you select Picture Off, the screen is turned off,
but the sound remains on. Press any button except the volume button
to turn on the screen.
■ Eco Sensor for 5 series : To enhance your power savings, the
picture settings automatically adapt to the light in the room.
✎ If you adjust the Backlight, the Eco Sensor will be set to Off.
Min. Backlight: When Eco Sensor is On, the minimum screen
brightness can be adjusted manually.
✎ If Eco Sensor is On, the display brightness may change (become
slightly darker in most cases) depending on the surrounding light
intensity.
■ No Signal Power Off: Sets how quickly the TV switches to standby
mode if no picture is being received.
✎ Disabled when an attached PC is in power saving mode.
■ Auto Power Off: The TV will automatically turn off when no user
operation is detected for 4 hours.
Auto Protection Time
If a still image remains on the screen for an amount of time you define,
the screen saver is activated to prevent the formation of ghost images
on the screen.
Support Menu
Self Diagnosis
■ Picture Test: Use to check for picture problems. If the problem
appears in the test picture, select Yes and follow the directions on
the screen.
■ Sound Test: Use the built-in melody to check for sound problems.
If the problem occurs during the test, select Yes and follow the
directions on the screen.
■ Signal Strength: (Digital channels only) An HD channel’s reception
quality is either perfect or the channels are unavailable. Adjust your
antenna to increase signal strength.
T Connecting a USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music, and/or movie files to
the USB jack on the back of the TV. A pop up window appears.
3. Press the MEDIA.P button on your remote. The Media Play menu
appears.
T Using the Media Play Menu
To open Media Play in the Menu, follow these steps:
1. Application on the left, and then press the ENTERE button.
2. Press the Ÿ or źbutton to select Media Play (USB), and then
press the ENTERE button.
3. Press the Ż or Ź button to select an icon (Videos, Music, Photos,
Settings), and then press the ENTERE button.
✎ Media Play might not work properly with unlicensed multimedia
files.
✎ Need-to-Know List before using Media Play (USB)
x Supported file systems are FAT and NTFS.
x Certain types of USB Digital camera and audio devices may not
be compatible with this TV.
x Media Play only supports USB Mass Storage Class (MSC)
devices. MSC is a Mass Storage Class Bulk-Only Transport
device. Examples of MSC are Thumb drives and Flash Card
Readers. Devices should be connected directly to the TV’s USB
port. USB HDD is not supported.
x Before connecting your device to the TV, please back up your files
to protect them from damage or loss of data. SAMSUNG is not
responsible for any data file damage or data loss.
x A USB device that requires high power (more than 0.5A) may not
be supported.
x Do not disconnect the USB device while it is loading.
x The higher the resolution of the image, the longer it takes to
display on the screen.
x If a file is corrupted or the TV does not support the file type, the
“Not Supported File Format” message appears.
-8-
x The TV cannot play MP3 files with DRM that have been
x
x
x
x
x
x
x
x
x
x
x
x
y Supported Video Formats
downloaded from a for-pay site. Digital Rights Management
(DRM) is a technology that supports the creation, distribution,
and management of digital content in an integrated and
comprehensive way, including protecting the rights and interests
of content providers, preventing illegal copying of contents, and
managing billing and settlements.
PTP devices are not supported.
If an over-power warning message is displayed while you are
connecting or using a USB device, the device may not be
recognized or may malfunction.
If the TV has no input during the time period set in Auto
Protection Time, the Screensaver will run.
The power-saving mode of some external hard disk drives may be
released automatically when you connect them to the TV.
If you use a USB extension cable, the TV may not recognize the
USB device or may not be able to read the files on the device.
If a USB device connected to the TV is not recognized, the list of
files on the device is corrupted, or a file in the list is not played,
connect the USB device to a PC, format the device, and check
the connection.
If a file you deleted from the PC is still found when you run Media
Play, use the “Empty the Recycle Bin” function on the PC to
permanently delete the file.
Photos only supports the sequential jpeg format.
The Videos option does not support the scene search and
thumbnail functions.
If the number of files and folders saved on a USB storage device is
over approximately 4000, the files and folders may not appear and
some folders may not open.
The maximum number of files the TV can display, including sub
folders, in one folder of a USB storage device is 2000.
The media may not play smoothly if you use a USB device rated
lower than USB 2.0.
Videos
1. In the Media Play menu, press the Ż or Ź button to select Videos,
and then press the ENTERE button.
2. Press the ŻŹŸź buttons to select a video in the file list.
3. Press the ENTERE button or ˜ (Play) button.
- The file name is displayed on the top of the screen with the playing
time.
- If video time information is unknown, playing time and the progress
bar are not displayed.
- During video playback, you can search using the Ż and Ź
buttons.
✎ In this mode, you can play movie clips contained in a game, but you
cannot play the game itself.
y Supported Subtitle Formats
- External
Name
File
Extension Container Video Codec
*.mp4
AVC
"*.avi
*.mkv"
.srt
Micro DVD
.sub or .txt
SubStation Alpha
.ssa
Advanced SubStation Alpha
Format
Xsub
AVI
Picture Format
SubStation Alpha
MKV
Text Format
Advanced SubStation Alpha
MKV
Text Format
SubRip
MKV
Text Format
MPEG-4 Timed text
MP4
Text Format
PS
*.3gp
3GPP
*.flv
flash
formats
30Mbps
6~30
30Mbps
1920x1080
6~30
30Mbps
MJPEG
640x480
Divx3.11/4.x/
1920x1080
5.1/6.0
MPEG4 SP/
1920x1080
ASP
H264
1920x1080
6~30
10Mbps
6~30
30Mbps
6~30
30Mbps
MJPEG
Divx
3.11/4.x/
5.1/6.0
MPEG4 SP/
ASP
6~30
10Mbps
640x480
1920x1080
6~30
6~30
30Mbps
30Mbps
1920x1080
6~30
30Mbps
H.264
1920x1080
6~30
30Mbps
MPEG2
1920x1080
6~30
30Mbps
H. 264 BP/
MP/HP
1920x1080
6~30
30Mbps
MPEG1
1920x1080
24/25/30
30Mbps
MPEG2
H. 264 BP/
MP/HP
MPEG4 SP/
ASP
H.264
1920x1080
24/25/30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
H.264
Sorenson
H.263
1920x1080
6~30
30Mbps
1920x1080
6~30
30Mbps
Audio
Codec
MP3 /
ADPCM /
AAC
"MP3 /
AC3 /
LPCM /
ADPCM
/ DTS
Core"
"MP3 /
AC3 /
LPCM /
ADPCM
/ WMA
/ WMA
Pro"
AC3 /
AAC /
MP3 /
DD+ /
HE-AAC
AC3 /
MPEG /
LPCM /
AAC
MP3
MP3
Video Decoder
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not
supported.
MPEG4 SP, ASP :
– Below 1280 x 720: 60 frame max
– Above 1280 x 720: 30 frame max
H.263 is not supported.
GMC is not support.
Audio Decoder
Supports up to WMA7, 8, 9 STD, 9 PRO, and 10 PRO
WMA 9 PRO and WMA 10 PRO support 5.1 channel.
(LBR mode of WMA Pro is not supported.)
WMA Lossless is not supported.
.ass
Container
"*.dat
*.mpg
*.mpeg
*.vob"
Bit rate
(Mbps)
6~30
y Video content will not play, or not play correctly, if there is an error in
the content or the container.
y Sound or video may not work if the contents have a standard bit rate/
frame rate above the compatible Frame/sec listed in the Supported
Video Formats table.
y If the Index Table contains an error, the Seek (Jump) function will not
work.
y The menu may take longer to appear if the video’s bit rate exceeds
10Mbps.
y Video content may not be play if there is too much content in one file.
- Internal
Name
TS
Frame
rate (fps)
Other Restrictions
.smi
.sub
ASF
"*.ts
*.trp
*.tp
*.m2ts"
.ttxt
SAMI
SubRip
SubViewer
"AVI
MKV"
"*.asf
*.wmv"
File extension
MPEG-4 timed text
MP4
Resolution
Divx3.11/4.x/
1920x1080
5.1/6.0
H264
1920x1080
Music
Media Play - Additional Functions
1. In the Media Play menu, press the ŻŹ buttons to select Music,
and then press the ENTERE button.
2. Press the ŻŹŸź buttons to select the desired Music in the file
list.
3. Press the ENTERE button or ˜ (Play) button.
✎ During music playback, you can search using the ŻŹ buttons.
✎ ƭ(REW) and μ (FF) buttons do not function during play.
✎ Media Play only displays files with MP3 file extensions. Other file
extensions are not displayed, even if they are saved on the same
USB device.
✎ If the sound is abnormal when playing MP3 files, adjust the
Equalizer in the Sound menu. (An over-modulated MP3 file may
cause a sound problem.)
■ Videos/Music/Photos Play Option menus
When playing a file, press the TOOLS button.
Photos
1. In the Media Play menu,, press the Ż or Ź button to select Photos,
then press the ENTERE button.
2. Press the Ż/Ź/Ÿ/ź buttons to select a photo in the file list.
3. Press the ENTERE button or ˜ (Play) button.
✎ NOTE
x While a photo list is displayed, press the ˜ (Play) / ENTERE
button on the remote control to start a slide show.
x All files in the file list section will be displayed in the slide show.
x During the slide show, files are displayed in order.
x During the slide show, you can adjust the slide show speed using
(ƭ) (REW) or (μ) (FF) button.
x You can move to other files using the Ż or Ź button.
x Media Play can play Music files automatically during a Slide Show
if Background Music is set to On.
x You cannot change the Mode in Background Music until the
Background Music file has finished loading.
y Supported Photo Formats
Image
JPEG
Photo
Resolution
Base-line
15360 x 8704
Progressive
1024 x 768
Perform the Sound Test to confirm your TV's audio is working properly.
(Go to MENU - Support - Self Diagnosis - Sound Test)
If the audio is OK, the sound problem may caused by the source or signal.
Check the volume control of the device (Cable/Sat Box, DVD, Blu-ray, etc.) connected to your TV.
The picture is good but there is no sound.
y If you are using an external device, check the device’s audio output option. Ex. You may need to change your cable box's
audio option if you have the cable box's audio output connected to your TV using an HDMI cable.
y Reboot the connected device by unplugging and then reconnecting the device's power cable.
The speakers are making an inappropriate
noise.
y Check the cable connections. Make sure a video cable is not connected to an audio input.
y For Antenna or Cable connections, check the signal information. A weak signal may cause sound distortion.
y Perform the Sound Test as explained above.
No Picture, No Video
y Make sure the AC power cord is securely plugged into the wall outlet and the TV.
y Make sure the wall outlet is working.
y Try pressing the POWER button on the TV to make sure the problem is not caused by the remote.
If the TV turns on, refer to ‘Remote control does not work’ below.
The TV turns off automatically.
y
y
y
y
There is no picture/video.
y Check the cable connections. (Remove and reconnect all cables connected to the TV and external devices).
y Set your external device’s (Cable/Sat Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input. For
example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.
y Make sure your connected devices are powered on.
y Be sure that the TV is set to the correct source by pressing the SOURCE button on the remote control.
y Reboot the connected device by unplugging and then reconnecting the device's power cable.
Other Restrictions
y CMYK and YCCK color space JPEGs are not supported.
Playing Multiple Files
■ Playing selected video/music/photo files
1. On the File List screen, highlight a file, and then press the Yellow
button on your remote.
2. Repeat Step 1 to select multiple files.
✎ NOTE
x A c mark appears to the left of the selected files.
x To cancel a selection, press the Yellow button again.
x To deselect all selected files, press the TOOLS button, select
Deselect All, and then the ENTERE button.
3. Press the TOOLS button, select Play Selected Contents, and then
press the ENTERE button.
■ Playing a video/music/photo folder
1. With the folders on your USB device displayed, use the ŻŹŸź
buttons to highlight a folder.
2. Press the TOOLS button, select Play Folder, and then press the
ENTERE button.
y Make sure the coaxial cable is connected securely.
y Run Auto Program to add available channels to the channel list.
Go to MENU - Channel - Auto Program then select Auto and make sure the correct Cable TV signal type is set in the
menu. There are 3 options. (STD, HRC, and IRC)
y Verify the antenna is positioned correctly.
y Check the Caption Setup menu. Try changing Caption Mode Service1 to CC1.
y Some channels may not have caption data.
y Compression of video contents may cause picture distortion, especially on fast moving pictures such as sports and action
movies.
y A weak signal can cause picture distortion. This is not a TV problem.
Purple/green rolling horizontal bars and
buzzing noise from the TV speakers with
Component cable connection.
y Remove the left and right audio connections from the set-top-box. If the buzzing stops, this indicates that the set-top-box
has a grounding issue. Replace the Component video cables with an HDMI connection.
The picture will not display in full screen.
y HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.
y Black bars on the Top & Bottom will be shown on movies that have aspect ratios different from your TV.
y Adjust the picture size option on your external device or change the TV to full screen.
y Replace the remote control batteries. Make sure you install the new batteries with their polarity (+/-) correct.
y Clean the transmission window located on the top of the remote control.
y Try pointing the remote directly at the TV from 5~6 feet away.
The cable/set top box remote control
does not turn the TV on or off, or adjust
the volume.
Program the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box user manual for the
SAMSUNG TV code.
A “Mode Not Supported” message
appears.
Check the supported resolution of the TV and adjust the external device’s output resolution accordingly. Refer to resolution
settings in this manual.
Caption on the TV menu is greyed out.
y You cannot select Caption in the TV menu when watching content from a device connected via HDMI or Component.
y Caption must be activated on the external device.
There is a plastic smell from the TV.
This smell is normal and will dissipate over time.
TV Signal Strength is unavailable in the
Self Diagnosis Test menu.
You can play movie and music
files repeatedly.
c
Picture Size
You can adjust the picture size to
your preference.
c
Picture Mode
You can adjust the picture
setting.
c
Sound Mode
You can adjust the sound setting.
c
Subtitle Setting
You can play the video with
Subtitles. This function only
works if the subtitles have the
same file name as the video.
c
Audio Format
You can select the digital audio
output format.
c
Audio Language
You can change the audio
language if the video has more
than one language.
c
c
c
c
c
Stop Slide Show /
Start Slide Show
You can start or stop a Slide
Show.
c
Slide Show Speed
You can select the slide show
speed during the slide show.
c
Background Music
You can set and select
background music when
watching a Slide Show.
c
Zoom
You can zoom into images in full
screen mode.
c
Rotate
You can rotate images in full
screen mode.
Information
You can see detailed information
about the played file.
This function is only available for digital channels received through an Antenna/RF/Coax connection.
TV is tilted to the right or left side.
Remove the stand base from the TV and reassemble it.
The Channel menu is greyed out
(unavailable).
The Channel menu is only available when you select the TV source.
Your settings are lost after 30 minutes or
every time the TV is turned off.
If TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. Please change from Store Demo mode
to Home Use mode using the Plug & Play procedure. Press the SOURCE button to select TV mode, go to MENU ĺ Setup ĺ
Plug & Play ĺ ENTERE.
You have intermittent loss of audio or video.
Check the cable connections and reconnect them.
Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for long term
use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.
- 13 -
✎ The wall mount kit is not supplied, but sold separately.
Install your wall mount on a solid wall perpendicular to the floor. If you
are attaching the wall mount to a wall made of building materials other
than drywall, please contact your nearest dealer for information about
the appropriate mounting hardware. If you install the TV on a ceiling or
slanted wall, it may fall and result in severe personal injury.
✎ NOTE
x Standard dimensions for wall mount kits are shown in the table
below.
x When purchasing our wall mount kit, a detailed installation manual
and all parts necessary for assembly are provided.
x Do not use screws that do not comply with the VESA standard
screw specifications.
x Do not use screws that are longer than the standard dimension
or do not comply with the VESA standard screw specifications.
Screws that are too long may cause damage to the inside of the
TV set.
x For wall mounts that do not comply with the VESA standard screw
specifications, the length of the screws may differ depending on
the wall mount specifications.
x Do not fasten the screws too firmly. This may damage the product
or cause the product to fall, leading to personal injury. Samsung is
not liable for these kinds of accidents.
x Samsung is not liable for product damage or personal injury when
a non-VESA or non-specified wall mount is used or the consumer
fails to follow the product installation instructions.
x Do not mount the TV at more than a 15 degree tilt.
x Always have two people mount the TV on a wall.
Product
Family
TV size in
inches
VESA screw hole specs
(A * B) in millimeters
19~22
75 X 75
26-28
100 X 100
c
c
c
Standard
Screw
Kensington Lock
Troubleshooting
The Kensington Lock is not supplied by Samsung. It is a device used
to physically fix the system when using it in a public place. Refer to the
manual provided with the Kensington Lock for additional information on
proper use.
✎ Please find a “K” icon on the rear of the TV. The Kensington slot is
beside the “K” icon.
✎ The position and color may differ depending on the model.
If the TV seems to have a problem, first review this list of possible problems and solutions. If none of these troubleshooting tips apply, visit samsung.
com, then click on Support, or call Samsung customer service at 1-800-SAMSUNG.
for 32" and above models
Display Modes (HDMI/DVI Input)
Mode
Resolution
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H / V)
IBM
720 x 400
640 x 480
832 x 624
1152 x 870
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 720
1280 x 800
1280 x 1024
1280 x 1024
1366 x 768
1440 x 900
1600 x 900RB
1680 x 1050
1920 x 1080
31.469
35.000
49.726
68.681
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
67.500
45.000
49.702
63.981
79.976
47.712
55.935
60.000
65.290
67.500
70.087
66.667
74.551
75.062
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
75.000
60.000
59.810
60.020
75.025
59.790
59.887
60.000
59.954
60.000
28.322
30.240
57.284
100.000
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
74.250
83.500
108.000
135.000
85.500
106.500
108.000
146.250
148.500
-/+
-/-/-/-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
+/+
-/+
+/+
+/+
+/+
-/+
+/+
-/+
+/+
MAC
4
200 X 200
M8
46~60
Settings
400 X 400
VESA DMT
■ DivX® Video On Demand : Shows the registration code authorized
for the TV. If you connect to the DivX web site and register with the
10-digit registration code, you can download the VOD activation file.
Once you run the file using Media Play, the registration is completed.
✎ For more information on DivX® VOD, visit “http://vod.divx.com”.
■ Information: Select to view information about the connected USB
device.
Do not install your Wall Mount Kit while your
TV is turned on. It may result in personal
injury due to electric shock.
1366 x
768
1920 x
1080
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
Caution of the cover-jack
Caution: Pulling, pushing, or climbing onto the TV may
cause the TV to fall. In particular, ensure that your children
do not hang over or destabilize the TV. Doing so may cause
the TV to tip over, resulting in serious injuries or death.
Follow all safety precautions provided on the included
Safety Flyer. For added stability, install the anti-fall device for
safety purposes, as described below.
Other Information
for 46", 50" models
To install a wall-mount from another manufacturer, use the Holder-Ring.
CAUTION: These servicing instructions are for use by
qualified service personnel only. To reduce the risk of
electric shock or fire hazard, do not perform any servicing
other than that contained in the operating instructions
unless you are qualified to do so.
TV Rear Panel
To prevent the TV from falling
Component Connections /
Screen Color
If you find that the color on your Samsung television’s screen is not correct or black and white, first run a Self Diagnosis test
on the TV to make sure there are no device issues.
y Self Diagnosis : MENU ĺ Support ĺ Self Diagnosis ĺ Picture Test
If the test is ok, try making sure:
y Your connections are all consistent. For example, if you’ve used the AV In jack on your TV, make sure you have used the
AV Out jack on your video source.
y Try making sure you have connected to the correct jacks. For example, if you use the Component jacks, labeled Pb, Pr,
and Y, to connect your TV and video source, make sure you have connected the blue Pb jack on the video source to the
blue Pb jack on the TV, the red Pr jack on the source to the red Pr jack on the TV, etc.
Screen Brightness
If you find that the colors on your Samsung TV are correct but just a little too dark or bright, there are some settings you
should check before calling for a repair.
y Backlight, Contrast, Brightness, Sharpness, Color, Tint (G/R) and so on. Go to “Picture” on the User Menu, and then
try adjusting these options.
Unwanted Powering off
If your Samsung TV appears to turn off by itself, there may be an issue with either your Timer settings or your Eco friendly No
Signal Power Off feature.
First make sure your Sleep Timer is not accidentally set. The Sleep Time allows you the comfort of falling asleep with the TV
still on but, turns it off after a certain period of time so as not to waste energy.
y Sleep Timer : MENU ĺ Setup ĺ Time ĺ Sleep Timer
If the Sleep Timer is not activated, you may have engaged the No Signal Power Off or Auto Power Off feature.
y No Signal Power Off : MENU ĺ Setup ĺ Eco Solution ĺ No Signal Power Off
y Auto Power Off : MENU ĺ Setup ĺ Eco Solution ĺ Auto Power Off
Trouble Powering On
Before you turn the TV on, find the red light on the right or left bottom of your TV. Press the power on button on the
TV or remote and the light should blink about 5 times before the TV turns on.
If you find that you are having trouble powering on your Samsung television, there are a number of things to check before
making a call to the service department.
y If you happen to be using the TV as a monitor and the stand-by light only blinks for a few seconds when you press the
power button, your PC is in sleep mode. To take your PC out of sleep mode, press a key on your keyboard or move the
mouse. Then try turning your TV on.
If you’re sure your power cord, remote control, and PC are functioning properly, you may be having a cable issue. If you have
a cable or satellite box, your TV may appear to be off because the cable or satellite box is not outputting a signal. To test the
signal output of your cable or satellite box, press the guide or info button on the cable or satellite box remote control. If the
screen displays the guide or info data, the problem is caused by the box.
Stand Assembly
If you have any trouble assembling the stand, refer to "Install the Stand" in the Start Up or Stand Installation Guide.
Cannot find channel
Re-run plug and play.
Poor picture
First, perform the Picture Test and to see if your TV is properly displaying the test image.
Go to MENU - Support - Self Diagnosis - Picture Test
If the test image is properly displayed, the poor picture may be caused by the source or signal.
The TV image does not look as good as it
did in the store.
If you have an analog cable/satellite box, upgrade to a digital set top box. Use HDMI or Component cables to deliver HD (high
definition) picture quality.
Cable/Satellite subscribers: Try HD channels from the channel line up.
Air/Cable Antenna connection: Try HD channels after running Auto program.
Many HD channels broadcast SD contents upscaled to HD. The picture quality of upscaled SD content is low.
y Adjust the Cable/Set top box video output resolution to 1080i or 720p.
✎
The picture is distorted: macroblock error,
small block, dots, pixelization.
y Compression of video contents may cause picture distortion, especially on fast moving pictures such as pictures from
sports and action movies.
y A weak signal can cause picture distortion. This is not a TV problem.
y Mobile phones used close to the TV (within 3.3ft) may cause noise in the picture on analog and digital channels.
Color is wrong or missing.
If you’re using a component connection, make sure the component cables are connected to the correct jacks. Incorrect or
loose connections may cause color problems or a blank screen.
✎
✎
The product shape may differ
depending on the model.
TV Holder kits are sold separately. To purchase a TV Holder kit,
contact Samsung Customer Care.
1. Insert the screws into the wall brackets and firmly fasten them to the
wall. Make sure the screws are firmly fixed to the wall.
✎ We strongly recommend you drive the screws into a stud.
2. Insert the screws through the TV brackets, and then fasten the
screws to the top VESA screw holes on the back of the TV.
3. Connect the brackets on the TV and the brackets on the wall with a
strong string or cable, and then tie the string or cable tightly to the
brackets.
✎ Verify all connections are properly secured. Periodically check the
connections for any sign of fatigue or failure. If you have any doubt
about the security of your connections, contact a professional
installer.
✎ Install the TV close to the wall so that it does not fall.
✎ Connect the string or cable so that the brackets on the wall are at
the same height or lower than the brackets on the TV. Untie the
string or cable before moving the TV.
This is part of the product’s design and is not a defect.
Select Home Use under Plug & Play mode. For details, refer to Plug & Play (Initial Setup).
✎
There is poor color or brightness.
y Adjust the Picture options in the TV menu. (Go to Picture Mode / Color / Brightness / Sharpness)
y Adjust the Energy Saving option in the TV menu. (Go to MENU - Setup - Eco Solution - Energy Saving)
y Try resetting the picture to view the default picture setting. (Go to MENU - Picture - Picture Reset)
There is a dotted line on the edge of the
screen.
y If the picture size is set to Screen Fit, change it to 16:9.
y Change the cable/satellite box resolution.
The product shape may differ depending on the model.
The picture is black and white.
y If you are using an AV composite input, connect the video cable (yellow) to the Green jack of Component input 1 on the
TV.
When changing channels, the picture
freezes or is distorted or delayed.
y If the TV is connected to a cable box, reset the cable box. (Disconnect and then reconnect the box's AC cord and wait until
the cable box reboots. It may take up to 20 minutes.)
y Set the output resolution of the cable box to 1080i or 720p.
- 12 -
JACK PANEL DETAIL / REAR VIEW
Specifications
This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce. However, there may be a few bright or
dark pixels on the screen. These pixels will have no impact on the performance of the product.
You can watch detailed troubleshooting videos at www.samsung.com/spsn.
Some functions and pictures shown in this manual are available on specific models only.
You can keep your TV in optimum condition by upgrading it with the latest firmware from the Samsung web site (samsung.com ĺ Support). To
upgrade, download the firmware to your computer, copy the firmware file to a USB memory stick, insert the USB memory stick into the TV's USB
slot, and then select Support > Software Upgrade in the TV's menu.
Storage and Maintenance
✎ If a sticker was attached to the TV screen, some debris can remain after you remove the sticker. Please clean it before watching the TV.
✎ The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using a soft cloth to
prevent scratches.
Clean the product with a soft cloth
dampened with in a small amount of water.
Do not use a flammable liquid (e.g. benzene,
thinners) or a cleaning agent.
■ UN19F4000 / UN22F5000
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
50°F to 104°F (10°C to 40°C)
10% to 80%, non-condensing
-4°F to 113°F (-20°C to 45°C )
5% to 95%, non-condensing
Model Name
UN19F4000
UN22F5000
Display Resolution
1366 x 768
1920 x 1080
Screen Size
(Diagonal)
19" Class
(18.5" measured diagonally)
22" Class
(21.5" measured diagonally)
Sound
Output
Dimensions (W x H x D)
Body
Do not spray water directly onto the
product. Any liquid that goes into the
product may cause a failure, fire, or electric
shock.
Cover-jack
- 11 -
POP (TV’s internal banner ad) appears on
the screen.
✎
✎
✎
If your Samsung television is flickering or dimming sporadically, you may need to disable some of its energy efficient features
like the Eco Sensor or the Energy Saving feature. Using your remote, follow the steps below to turn these features off or
on.
y Energy Saving : MENU ĺ Setup ĺ Eco Solution ĺ Energy Saving
y Eco Sensor : MENU ĺ Setup ĺ Eco Solution ĺ Eco Sensor for 5 series
Securing the TV to the Wall
Preparing before installing Wall-Mount
You see small particles when you look
closely at the edge of the frame of the TV.
✎
Possible Solution
Flickering and Dimming
Optimal resolution
4 series:1366 x 768@60Hz / 5 series: 1920 x 1080@60Hz
M4
32-42
Problem
Assembling the Stand Wire Holder
Quantity
LED-TV
c
With stand
Weight
Without Stand
With Stand
3W x 2
17.8 X 11.0 X 1.9 inches
(453.7 X 281.3 X 49.5 (mm))
17.8 X 12.3 X 4.9 inches
(453.7 X 314.2 X 124.9 (mm))
20.2 X 12.6 X 1.7 inches
(513.1 X 321.5 X 43.8 (mm))
20.2 X 14.4 X 6.6 inches
(513.1 X 366.5 X 169.6 (mm))
5.5 lbs (2.5 kg)
5.7 lbs (2.6 kg)
5.7 lbs (2.6 kg)
6.3 lbs (2.9 kg)
(Unit: inches)
Model name
1
2
3
4
5
6
UN19F4000
3.0
3.1
3.1
6.9
2.9
2.9
UN22F5000
4.4
4.4
2.6
8.2
2.9
2.9
■ UN32F4000 / UN32F4050 / UN32F5000 / UN32F5050 / UN40F5000 / UN40F5050 / UN46F5000 / UN46F5050 / UN50F5000 / UN50F5050
License
Model Name
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
Others
The remote control does not work.
c
Repeat Mode
Photos
- 10 -
Ensure the Sleep Timer is set to Off in the Time menu.
If your PC is connected to the TV, check your PC power settings.
Make sure the AC power cord is plugged into the wall outlet and TV securely.
When you are watching a TV connected to an antenna or to a cable connection, the TV will turn off after 10 - 15 minutes if
there is no signal.
RF(Cable/Antenna) Connection
The picture is distorted: macroblock, error,
small block, dots, pixelization.
Title
You can select another video file
to play directly.
Music
The wall mount kit (sold separately) allows you to mount the TV on the
wall.
For detailed information about installing the wall mount, see the
instructions provided with the wall mount kit. Contact a technician for
assistance when installing the wall mount bracket. Samsung Electronics
is not responsible for any damage to the product or injury to yourself or
others if you elect to install the wall mount on your own.
Sound Problem
No Caption on digital channels.
Videos
Installing the Wall Mount Kit
There is no sound or the sound is too low at
maximum volume.
The TV is not receiving all channels.
Operation
Using the Setup Menu
-9-
The TV will not turn on.
Category
Wall Mount Kit Specifications (VESA)
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx. com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in
order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com
for more information on how to complete your registration. Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274 DivX®, DivX
Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.
UN32F4000
UN32F4050
Display Resolution
Screen Size
(Diagonal)
1920 x 1080
32" Class
(31.5" measured diagonally)
32" Class
(31.5" measured diagonally)
Sound
Output
Dimensions (W x H x D)
Body
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
With stand
Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467,
7,272,567, 7,668,723, 7,392,195, 7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol, and DTS and the Symbol together are registered
trademarks & DTS Premium Sound is a trademark of DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
Weight
Without Stand
With Stand
Manufactured under a license from U.S. Patent No’s: 6,285,767, 8,027,477, 5,319,713, 5,333,201, 5,638,452, 5,771,295, 5,970,152,
5,912,976, 7,200,236, 7,492,907, 8,050,434, 7,720,240, 7,031,474, 7,907,736 and 7,764,802. DTS, the Symbol, and DTS and the Symbol
together are registered trademarks & DTS Studio Sound is a trademark of DTS, Inc.
©2012 DTS, Inc. All Rights Reserved.
Model Name
Open Source License Notice
Open Source used in this product can be found on the following webpage. (http://opensource.samsung.com) Open Source License Notice is written only English.
To send inquiries and requests for questions regarding open sources, contact Samsung via Email (oss.request@samsung.com).
„ This product uses some software programs which are distributed under the Independent JPEG Group.
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1995-2008 International Business Machines Corporation and others All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the
Software is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright
notice(s) and this permission notice appear in supporting documentation.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
All trademarks and registered trademarks mentioned herein are the property of their respective owners.
- 14-
Screen Size
(Diagonal)
29.0 X 17.1 X 1.9 inches
(737.9 X 435.8 X 49.5 (mm))
29.0 X 19.1 X 9.9 inches
(737.9 X 487.0 X 252.6 (mm))
29.0 X 17.5 X 1.9 inches
(738.0 X 445.4 X 49.0 (mm))
29.0 X 19.9 X 7.5 inches
(738.0 X 505.8 X 191.7 (mm))
11.4 lbs (5.2 kg)
12.5 lbs (5.7 kg)
11.4 lbs (5.2 kg)
12.3 lbs (5.6 kg)
11.0 Ibs (5.0 kg)
12.3 Ibs (5.6 kg)
UN40F5000 / UN40F5050
UN46F5000 / UN46F5050
UN50F5000 / UN50F5050
With stand
Weight
Without Stand
With Stand
✎
✎
✎
✎
✎
Model name
1
2
3
4
5
6
UN32F4000 / UN32F4050
7.7
4.7
4.4
19.0
7.8
7.8
UN32F5000 / UN32F5050
7.8
4.8
4.0
19.1
7.8
7.8
UN40F5000 / UN40F5050
9.8
6.9
6.2
40” Class
(40.0" measured diagonally)
46" Class
(45.9" measured diagonally)
44.7 X 26.2 X 1.9 inches
(1135.4 X 668.0 X 49.8 (mm))
44.7 X 28.6 X 9.2 inches
(1135.4 X 727.9 X 235.0 (mm))
17.6 Ibs (8.0 kg)
20.9 Ibs (9.5 kg)
23.8 Ibs (10.8 kg)
27.1 Ibs (12.3 kg)
28.6 Ibs (13.0 kg)
31.9 Ibs (14.5 kg)
6.9
30.1
15.7
15.7
6.6
32.7
15.7
15.7
NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions prior to
performing installation of your TV. Not responsible for typographical or printed errors.
© 2013 Samsung Electronics America, Inc
Design and specifications are subject to change without prior notice.
This device is a Class B digital apparatus.
For information about your TV's power requirements and more about power consumption, refer to the label attached to the product.
Typical power consumption is measured according to Energy Star Program requirements for televisions.
Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/
recyclingdirect or call, (877) 278-0799.
- 15 -
7.8
6.4
6.8
50" Class
(49.5" measured diagonally)
41.7 X 24.6 X 1.9 inches
(1059.6 X 626.2 X 49.4 (mm))
41.7 X 27.0 X 9.2 inches
(1059.6 X 686.1 X 235.0 (mm))
7.8
12.1
14.0
10W x 2
36.5 X 21.7 X 1.9 inches
(928.2 X 552.3 X 49.4 (mm))
36.5 X 24.1 X 9.2 inches
(928.2 X 612.2 X 235.0 (mm))
24.4
UN46F5000 / UN46F5050
UN50F5000 / UN50F5050
1920 x 1080
Sound
Output
Dimensions (W x H x D)
Body
(Unit: inches)
10W x 2
29.0 X 17.1 X 1.9 inches
(737.9 X 435.8 X 49.5 (mm))
29.0 X 20.0 X 7.5 inches
(737.9 X 509.1 X 191.7 (mm))
Display Resolution
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
UN32F5000 / UN32F5050
1366 x 768
- 16 -
IMPORTANT SAFETY PRECAUTIONS
• Placing the television on a platform, stand, cabinet, table or other surface which is:
-
recommended by Samsung or sold with the product;
-
secure and stable;
-
sufficiently wider in the base than the base measurement of the television;
strong and large enough to support the size and weight of the television.
• Positioning the television close to the wall to avoid the possibility of the television falling when pushed.
• Ensuring your television is installed by an authorized Samsung installer.
• Following the instructions for wall mount1ng in the installation manual and using the mounting equipment supplied by Samsung.
• Placing the television toward the back of the furniture or surface on which it is placed.
• Ensuring that the television does not hang over the edge of the furniture or surface on which it is placed.
• Not hanging anything from or on the television.
• Anchoring both the television and the furniture on which it is placed to a suitable support especially in the case of tall furniture, such as
• cupboards or bookcases which exceed one metre in height. This can be done by using sturdy brackets, safety straps or mounts that
are made specifically for flat screen televisions.
• Not placing any material between the television and the furniture on wh1ch it is placed.
• If the furniture on which the television is placed has drawers, cabinets or shelves under the television, taking steps to prevent children
from climbing, such as installing safety latches so the doors cannot be opened.
• Keeping pets away from the television
• Educating children about the dangers of climb1ng on furniture to reach the telev1sion or its control.
Failure to take these safety precautions may cause the television to fall from the stand or mounting equipment,
causing damage or serious injury.
Regulatory Compliance Statements
-
Federal Communicatio ns Commission (FCC) - USA
Industry Canada Equipment Standard for Digital Equipment (ICES-003) - Canada
Voluntary Control Council for Interference (VCCI) - Japan
Bureau of Standards Metrology and Inspection (BSMI) - Taiwan
Korea Communications Commission(KCC) - Republic of Korea
Italian Post Ministry (Homologation) - Italy
FCC Class A Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
~
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference w hen the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Class 8 Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
~ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the inst ructions,
may cause harmful interference to radio communications. How ever, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio o r televisio n reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced rad io/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment. If necessary, consult with your dealer or an experienced radio/television technician for additiona suggestions. You may find the
booklet called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications
Commission. It is available from the U.S. Government Printing Office. Washington, DC 20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD.
America QA Lab of Samsung
3351 Michelson Drive
Suite #290, Irvine, CA92612 USA
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product. Provided wit h this monitor is a detachable
power supply cord w ith IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar
configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor
and that the ampere rating of the computer convenience outlet is equal or exceeds the monitor vo ltage rating. For 120 Volt applications,
use only UL Listed detachable power cord with NEMA configuration 5- 15P type(parallel blades) plug cap. For 240 Volt applications use
only UL Listed detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. This television receiver
provides display of television closed captioning in accordance w ith Section 15. 119 of the FCC rules. (TV broadcast receivers with picture
screens 13 inches or larger in diameter models only)
/CES-003 Class A Notice -Avis NMB-003, C/asse A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de Ia classe A est conforme Ia norme NMB-003 du Canada.
a
ICES-003 Class B Notice -Avis NMB-003, C/asse B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de Ia classe B est conforme a Ia norme NMB-003 du Canada.
VCCI Class A Notice
;: Cl)~Th[lj:, ? 7 A. A tUIH~f.tij~@:~9 o
;::, Cl)~@: ~*j}!~l:Jt~fj!:FFJ9..@ C ~i~9Ji~~ 'JI ~~;::, 9;::, C fJ(~ L) *9 o
;: Cl)~.g.~=lj:il:FFJ~tJ{iiJil;J]t.j~~ ~~9..@ J:? ~* ~ n..@;: .t tJ{~ LJ *9
0
VCCI Class B Notice
;: Cl)~@:lj:, ? 7 A B fUIH~tf.j~@:~9
;: Cl)~@: lj:, *l}!~l:Jt~il:FFJ9..@;: .t ~ EliY-:1 .t L- -c l '*9fJ{, ;: Cl)~@:fJ{7 :/>t~-T v t · :/ 3
n..@ .t, ~i~ll!~~sl ~~;: 9;: .t tJ{~ LJ *9
lfl(j.Jk~Bjj:J:I=V£-::>"'C:iE l-l'lfl1 L)j.Jkl'~ l.- "'Cl'~ l' o
0
:/~i~~t!U=ilH~ L-
-c il:FFJ ~
0
CCC Class A notice - China
~~AmF~. ~~~~~$. ~F~~-~~-~~~~tt .
~~Mffl~l'. ~··~m~~X~tt*UW~~fi~m~ .
BSMI Class A Notice
The following statement is applicable to products shipped to Taiwan and marked as Class A on the product
compliance label.
!35fff!ff}ff :
~~~••m•~~ · rr@tt•~~~m~·~~@~~~~~~·tt~MM~~·
~m~•*~*~~~®~=~~• ·
CE
BSMI Class A Notice
Products with the CE marking comply with the EMC Directive(2004/ 108/ EC) and the Low Voltage
Directive(2006/95/EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:
- EN55022: Radio Frequency Interference
- EN55024: Electromagnetic Immunity of Information Technology Equipment
- EN61 000-3-2: Power Line Harmonics
- EN61000-3-3: Voltage Fluctuations
- EN55013: Radio disturbance characteristics of broadcast receivers and associated equipments
- EN55020: Electromagnetic immunity of broadcast receivers and associated equipm
European Class A Warning
(If the user manual declares the product as Class A, following statement applies.)
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
As 7/7/
(gj.EF~ W-&5-~tJ7txfxHJ
Ol 7 171 ~ ~.Ef!. § (AE}) ~A:~II.f~~ 7 1 7 1 £ Ai It)'oHA:f Ef. ~ Af§A: ~ ~ Ol ~ ~ "? Qj 'OfAI 7 II::lf2.fO:j , 7 ~ ~ 2.12.1 :AI ~ OiiAi
Af§o~ ~ ~~ ~ ~
0£
~ LICf.
(7f~ ~ W-&5-~t!7/XfXH)
Ol 7171~ 7~~§(8 8 ) ~A:~Il~~ ~7 171£ Ai ~£ 7~~0i1Ai A~§o~~ ~ ~ ~~ 0 £ otO:J,
8 8 7/7/
~-,::; Lief.
Italian Homologation Notice
Questo apparecchio e fabbricato in conformita al D.M.28.08.95 n.548
ed in particolare a quanto specificate nell Art. 2, comma 1.
Questo apparecchio e fabbricato nella U. E. in conformita al D.M.28.08.95 n.548
Art.2, comma 1 ed al D.M.26.03.92 Art.1
- For products produced in countries except European Community
Questo apparecchio e fabbricato in conformita al D.M.28.08.95 n.548
ed in particolare a quanto specificate nell Art.2, comma 1.
- For products produced in European Community
Questo apparecchio e fabbricato nella U.E. in conformita al D. M.28.08.95 n.548
Art.2, comma 1 ed al D. M.26.03 .92 Art.1
.2:::
A:I~OiiAi A~§ W
4
Important Safety Instructions (UL Only)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
1 0. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11 . Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen 1nto the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
1.
2.
3.
4.
5.
6.
7.
8.
expose this
• Ventilation
Do not place the apparatus in a rack or bookcase. Ensure that there is adequate ventilation and that you've followed that manufacturer's
instructions for mounting and installation.
MPR II Compliance (MPR II applied model only)
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
Mercury Statement {LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only)
Contains Mercury, Dispose According to Local, State or Federal Laws
Wiring the Mains Power Supply Plug(UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face
of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same
colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should
obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative but to cut off the
plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows :
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
Russia Only - PCT Notice
(@
AB57
MPR II Compliance (MPR II applied model only)
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
EU Eco-Label (EU Eco-Label applied model only)
Products which have model codes that end in XU are intended for the UK market. Samsung has not applied for Ecolabels for products with this
specific model code.
***
*
c- *
* \: *
*
*
EU')j:,!
Better for the environment. ..
• High Energy Efficiency
• Reduced C02 emissions
• Designed to facilitate repair and recycling
Ecolabel
... better for you.
www.ecolabel.eu
(
EU Ecolabel: HU/022/02
J
SAMSUNG Electronics makes an effort to develop environment-friendly product that minimizing an impact to environment through whole
process from getting raw materials, production, transportation, usage and end-of-life disposal by adding 'environment ' on function, price,
quality, design that were the essence for product development.
These environmental characteristics are endorsed by the award of the European Eco-label (also known as the Euro Flower) issued by
the European Commission as approval of the product environmental status for energy saving, facilities for recycling and a host of other
features. The full list of criteria and more information on the ecolabel canbe found at the web-site address: http://www.ecolabel.eu
Recycling Information (Take-back offer)
For recycling information for our products, please contact the company corresponding to your region of residence.
For those who reside in other countries, please contact a nearest local Samsung dealer for recycling information for the products to be treated
in environmentally acceptable way.
The information of Regional Takeback Schemes can be found at Samsung's web-site.
http://www.samsung.com/recycling_compliance
CIS Only
®
CII1MB011 «He ,QI151 nll1ll.!eBo~ npo.QYK1..1111111» np111MeH51eTc51 B coorsercrs111e c rexHII1YeCKII1M pernaMeHTOM
TaMO>KeHHOro co103a «0 6e3onacHOCTII1 ynaKOBKII1» 005/2011 111 yKa3biBaer Ha ro, 4TO ynaKOBKa ,QaHHoro
npO.QYKTa He npe.QHa3HaYeHa ,[11151 nosropHoro 111Cn011b30BaHII151 111 na.Q118>KII1T yr111111113a1..1111111. YnaKOBKY
,QaHHOro npo,QyKTa 3anpell.!aeTC51 111Cn011b30BaTb ,[11151 xpaH8HII151 nll1ll.!eBO~ npO.QYK1..1111111.
0
®
Cli!MB011 «nem51 Me6111yca» yKa3blsaer Ha B03MO>KHOCTb yrlilnll13a'-llilll1 ynaKOBKiil. Cli!MBon MO>KeT
6b1Tb AOnOnHeH 0603H8YeHI!I8M M8Tep111ana ynaKOBKiil 8 8111.Qe l..llilcJJpOBOrO 1!1/lilnlil 6yKB8HHOro
o6o3Ha4eHI!I51.
a
CIIIMB011 Ke.QeH.QiK O.Qal0'blf-\ 005/2011 rexHII1K811bl~ pernaMeHTiHe ca~Kec ~011.QaHbl11a.Qbl >KaHe OCbl
SHiMHif-1 ~anTaMaCbiH eKiHWi peT na~,Qa11aHyra apH811M8f8HbiH >K<3He >KOIOfa >K8T8TbiHbiH K9pCeTe,Qi.
0Cbl SHiMHif-1 ~anT8M8CbiH a3bl~-ry11iK SHiM.QepiH C810'ay ywiH na~AanaHyfa Tbl~biM C811b1H8,Qbl.
Cli!MBon ~anraMaHbl >KOIO MyMKiHAiriH Kepcere.Qi. Cli!MBOn caHAbl~ KOA >KaHe/HeMece apin
6enrinepi rypiHAeri ~anraMa Marepl!lanbiHblf-\ 6enriciMeH ronbll0'blpblnYbl MYMKiH.
1111111111111111111111111111111111111111111
B N68-04972A-O 1
Screws and Guide stand location
~
::J
0
>.Q)
..cc
:t:::O
:;::..c
c..
.!!? t:::
(Except LED ES 8000 and higher)
..CC"C
-E
~Ul
(.)
U)
"CC
t
0
c..
c..
-::sen
c
'I-C..
en
......._
-Q,)o
E
E
::::l
Cl.~
.Cu
..
u
C')
c
::::l
en
ca
a,) E
Cl)
LED TV
26"-46"
Location
0
a,)
.c
Size
t:
0
·->
Product
~
en
0
(..)
....c
C')
c
::::l
en
ca E
c.,)
~
en
Cl.
Cl.
=
--
Cl)
l:noo::;t
Screws/
Guide-Stand
Co
:::StO
en~"-
Em
--- --- ---
cam
en'?
00
-00
Plasma
TV
-oo
ca,
(.).,.....
43"-51"
--Screws(
Guide-Stand
w
a:
0
~-
l-
en
0
1-
z
a:
LED 55"
LED TV
Plasma 59"
Plasma TV
And larger
::J
1-
w
a:
1-
0
z
0
0
--- --- --.........
Screws/
Guide-Stand
English
Screws and guide stand package is placed in the Styrofoam on top.
Espaiiol
Los tornillos y Guide Stand se encuentran localizados en el Styrofoam superior.
Fran~ais
Les vis et le paquet du guide du support sont places dans Ia mousse de
polystyrene sur le dessus.
Top 6 Troubleshooting Tips
:d TV Handling Guide
TV 6 Problemas Principales
1 . Can't Connect with Network or Apps (For internet supported model only) 1. No se puede conectar con Ia Red o Apps (Solo para model as que
soporten conexi6n a internet)
• Make sure there is a network connection
• Asegurese que el equipo este conectado a una red
(Menu ~ Network ~ Network status)
(Menu ~ Red ~ Estado de Red)
• Contact your service provider
• Contactar a su proveedor de Internet
2. No Picture/Sound or Distorted Picture/Sound with an External Device
• Make sure your connection to the device is correct.
• Perform a TV Self Diagnosis to identify the problem
(Menu ~ Support ~ Self Diagnosis ~ Sound or Picture Test)
• Change the picture size (Use "P. Size" button on your remote)
3. Poor Picture Quality
• Verify your signal is High Definition o r Standard Definition
(Contact your service provider)
3. Mala Calidad de Imagen
• Verificar si su senal es Alta Definicion o Definicion Regular
(Contactar a su proveedor de Serviciqs)
4. Your Settings are Lost after 30 Minutes
• Change to Home Mode
("Tools" on your remote ~ Store Demo Off)
6. Can't See All Apps or Apps Not Working
Reset Sm art Hub
(Too ls in main page of Smart Hub ~ Settings ~ Reset
Enter with Password, Default Password is 0000)
t ',:: ;>f ::;Cll o) i ( (.•dt<;<.~ ';.f( Pn
·. i•:•n;.• ' ' " 1~-.:,•-: <!,,, \'•:.i ~ ~
•
,', ';V' · ;Lr· :.t ~ (:.' >~!tit·<_:'
, . jl •
~
ous soulevez un televiseur 55" ou plus, si votre pouce touche directement
.. dn, vous pouvez en dommager l'e cran. Samsung recommande vous soulevez
te televiseur, comme indique dans Ia photo.
r-;;,
~
II.• - .• II II II. Btl•
~·-
0
.
i!J ..:.•. 8
~
~-
1m age the screen . Samsung recommends you lift up the TV as shown in PIC.
R
6. No se ven todas las Aplicaciones o no funcionan
Resetear Smart Hub
(Herramtentas en Ia pagina princtpal de Smart Hub ~ Conftguracion
lntroducir Ia Contrasena, Ia Contrasena Predeterminada es 0000)
·.
1 you lift up a 55" or larger TV, your thumd touches the sareen directly, you
;e levante una TV de 55" o mayor, si el dedo pulgar toea Ia pantalla
nte, puede dar'iar Ia pantalla. Samsung recomienda que levante Ia TV
1uestra en Ia FIG.
5. " Senates Debiles o lnexistentes" Mensaje desplegado en
TV Mode I No puede encontrar canales
• Presione el bot6 n "Source" en su control remota
• Corra Auto Program e inicie busqueda de canales
(Menu ~ Sistema ~ Plug & Play ~ Enter)
~
·I ish
I
4. Su configuraci6n se pierde despues d e 30 minutos
• Cambiar a Uso Domiciliario
(Use el boton "Tools" del control rernoto ~ Demo Cornercio Desac.)
5. "Weak or No Signal" Displayed in TV Mode/Cannot Find Channel
• Press Source button on your remote
• Run Auto Program and search for channels
(Menu ~ System ~ Plug & Play ~ Enter)
Scan the QR code to view
our helpful How-to Videos
2. No hay lmagen/sonido o Distorsi6n de Imagen/sonida con un
dispositive externo
• Asegure que Ia conexion fisica del dispositive sea correcta
• Para identificar el problema, realice un Auto d iagnostico en Ia TV
(Menl.J ~ So porte de Tecnico ~ Au!odiagnostico --?l'rullba de Imagen o Sonido)
• Cambie el tamano de Ia irnagen (Use el boton "P. Size" del control remota)
.
Screen Care Guide
Reset
English
Do not spray cleaning solutopn directly onto the TV screen. Spray the solution onto
a cleaning cloth first, and then clean the screen .
Espaiiol
No rocie Ia soluci6n de limpieza directamente sobre Ia pantalla del televisor .
Rocie Ia soluci6n sobre un par'io de limpieza, y luego limpie Ia pantalla.
Franc;ais
Ne pas pulveriser Ia solution de netto yage direnctement sur l'e cran du televiseur.
Pulveriser Ia solution sur un chiffon de netto yaged' abord , puis nettoyer l'e cran.
Download PDF

advertising