2017 RAM Commercial ProMaster Uconnect 5.0/5.0NAV Radio Book

UCONNECT 5.0/5.0 NAV
OWNER’S MANUAL
SUPPLEMENT
SECTION
TABLE OF CONTENTS
PAGE
1
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2
3
ALL ABOUT UCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3
4
RADIO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4
5
MEDIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5
6
UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6
7
UCONNECT PHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7
8
MORE BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8
9
NAVIGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
9
SAFETY GUIDELINES
CONTENTS
䡵 SAFE USAGE OF THE UCONNECT SYSTEM. . . . . .4
▫ FCC Declaration . . . . . . . . . . . . . . . . . . . . . . . . .4
▫ Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
▫ Information About Radio Frequency Radiation . . . .5
▫ Disc Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
䡵 CYBERSECURITY . . . . . . . . . . . . . . . . . . . . . . . . .6
1
4 SAFETY GUIDELINES
SAFE USAGE OF THE UCONNECT SYSTEM
• Read all instructions in this manual carefully before
using your system to ensure proper usage!
• Permanent hearing loss may occur if you play your
music or the system at loud volumes. Exercise caution
when setting the volume on your system.
• Keep drinks, rain and other sources of moisture away from
your system. Besides damage to your system, moisture can
cause electric shocks as with any electronic device.
NOTE: Many features of this system are speed dependent.
For your own safety, it is not possible to use some of the
touchscreen features while the vehicle is in motion.
• If necessary, use a lint-free cloth dampened with a
cleaning solution, such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Be sure
to follow the solvent manufacturer’s precautions and
directions.
Disc Player
• Do not insert any damaged, warped, scratched or dirty
discs into the Disc Player.
• Discs that have been modified with an adhesive label
should not be used in the Disc Player.
• Do not insert more than one disc at a time into the drive
slot.
Touchscreen
FCC Declaration
• Do NOT attach any object to the touchscreen, doing so
can result in damage to the touchscreen.
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
• Do not press the touchscreen with any hard or sharp
objects (pen, USB stick, jewelry, etc.) which could scratch
the touchscreen surface!
• Do not spray any liquid or caustic chemicals directly on
the screen! Use a clean and dry micro fiber lens cleaning
cloth in order to clean the touchscreen.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
SAFETY GUIDELINES 5
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Increase the separation between the equipment and
receiver.
• Consult the dealer or an experienced radio technician for
help.
Information About Radio Frequency Radiation
Exposure To Radio Frequency Radiation
The radiated output power of the internal wireless radio
is far below the FCC radio frequency exposure limits.
Nevertheless, the wireless radio shall be used in such a
manner that the radio is 20 cm (200 mm) or further from
the human body.
The internal wireless radio operates within guidelines
found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.
The radio manufacturer believes the internal wireless radio
is safe for use by consumers. The level of energy emitted is
far less than the electromagnetic energy emitted by wireless devices, such as mobile phones. However, the use of
wireless radios may be restricted in some situations or
environments, such as aboard airplanes. If you are unsure
of restrictions, you are encouraged to ask for authorization
before turning on the wireless radio.
1
6 SAFETY GUIDELINES
CYBERSECURITY
Your vehicle may be a connected vehicle and may be
equipped with both wired and wireless networks. These
networks allow your vehicle to send and receive information. This information allows systems and features in your
vehicle to function properly.
Your vehicle may be equipped with certain security features to reduce the risk of unauthorized and unlawful
access to vehicle systems and wireless communications.
Vehicle software technology continues to evolve over time
and FCA US LLC, working with its suppliers, evaluates
and takes appropriate steps as needed. Similar to a computer or other devices, your vehicle may require software
updates to improve the usability and performance of your
systems or to reduce the potential risk of unauthorized and
unlawful access to your vehicle systems.
The risk of unauthorized and unlawful access to your
vehicle systems may still exist, even if the most recent
version of vehicle software (such as Uconnect software) is
installed.
WARNING!
• It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle systems,
including safety related systems, could be impaired or
a loss of vehicle control could occur that may result in
an accident involving serious injury or death.
• ONLY insert media (e.g., USB, SD card, or CD) into
your vehicle if it came from a trusted source. Media of
unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase
the possibility for vehicle systems to be breached.
• As always, if you experience unusual vehicle behavior, take your vehicle to your nearest authorized
dealer immediately.
SAFETY GUIDELINES 7
NOTE:
• FCA or your dealer may contact you directly regarding
software updates.
• To help further improve vehicle security and minimize the
potential risk of a security breach, vehicle owners should:
• Routinely check
www.driveuconnect.com/software-update
to learn about available Uconnect software updates.
• Only connect and use trusted media devices
(e.g. personal mobile phones, USBs, CDs).
Privacy of any wireless and wired communications cannot
be assured. Third parties may unlawfully intercept information and private communications without your consent.
For further information, refer to “Onboard Diagnostic
System (OBD II) Cybersecurity” in “Maintaining Your
Vehicle” in your Owner’s Manual.
1
INTRODUCTION
CONTENTS
䡵 UCONNECT 5.0 SYSTEM . . . . . . . . . . . . . . . . . . .10
䡵 UCONNECT 5.0 SYSTEM W/NAVIGATION —
IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2
10 INTRODUCTION
UCONNECT 5.0 SYSTEM
INTRODUCTION 11
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
CAUTION!
Do NOT attach any object to the touchscreen, doing
so can result in breaking the touchscreen.
3 — BACK
Push the BACK button to return to a previous menu or
screen.
4 — ENTER/BROWSE & TUNE/SCROLL
Push the ENTER/BROWSE button to accept a highlighted
selection on the screen. Rotate the TUNE/SCROLL rotary
knob to scroll through a list or tune a radio station.
5 — MORE
Push the MORE button on the faceplate to access additional options such as: Trip and Clock.
6 — PHONE
1 — EJECT
Push the EJECT button to eject the disc.
Push the PHONE button to access the Uconnect Phone
feature.
2 — SETTINGS
7 — COMPASS
Push the SETTINGS button to access the Uconnect setting
features.
Push the COMPASS button on the faceplate to display the
current direction of the vehicle.
2
12 INTRODUCTION
8 — MEDIA
11 — MUTE
Pushing the MEDIA button will allow you to switch to
Media mode (Disc, USB/iPod, AUX, Bluetooth.)
Push the MUTE button for activation/deactivation of the
volume.
9 — RADIO
12 — SCREEN ON/OFF
Push the RADIO button on the faceplate to enter Radio
Mode. The different tuner modes; AM, FM and SXM –
If Equipped can be selected by pushing the corresponding
button on the touchscreen while in the Radio Mode.
Push the SCREEN ON/OFF button on the faceplate to turn
the touchscreen ON or OFF.
10 — ON/VOLUME
Rotate the rotary knob to adjust the Volume. Push the
ON/VOLUME button to turn on the system. Push the
ON/VOLUME button a second time to turn off the system.
INTRODUCTION 13
UCONNECT 5.0 SYSTEM W/NAVIGATION — IF EQUIPPED
2
14 INTRODUCTION
CAUTION!
Do NOT attach any object to the touchscreen, doing
so can result in breaking the touchscreen.
5 — MORE
Push the MORE button on the faceplate to access additional options such as: Trip and Clock.
6 — PHONE
1 — EJECT
Push the EJECT button to eject the disc.
Push the PHONE button to access the Uconnect Phone
feature.
2 — SETTINGS
7 — NAVIGATION
Push the SETTINGS button to access the Uconnect setting
features.
Push the NAV button to access the navigation feature.
3 — BACK
Pushing the MEDIA button will allow you to switch to
Media mode (Disc, USB/iPod, AUX, Bluetooth.)
Push the BACK button to return to a previous menu or
screen.
4 — ENTER/BROWSE & TUNE/SCROLL
Push the ENTER/BROWSE button to accept a highlighted
selection on the screen. Rotate the TUNE/SCROLL rotary
knob to scroll through a list or tune a radio station.
8 — MEDIA
9 — RADIO
Push the RADIO button on the faceplate to enter Radio
Mode. The different tuner modes; AM, FM and SXM – If
Equipped can be selected by pushing the corresponding
button on the touchscreen while in the Radio Mode.
INTRODUCTION 15
10 — ON/VOLUME
Rotate the rotary knob to adjust the Volume. Push the
ON/VOLUME button to turn on the system. Push the
ON/VOLUME button a second time to turn off the system.
11 — MUTE
Push the MUTE button for activation/deactivation of the
volume.
12 — SCREEN ON/OFF
Push the SCREEN ON/OFF button on the faceplate to turn
the touchscreen ON or OFF.
2
ALL ABOUT UCONNECT
CONTENTS
䡵 WHAT IS UCONNECT? . . . . . . . . . . . . . . . . . . . .18
䡵 IDENTIFYING YOUR RADIO . . . . . . . . . . . . . . . .20
3
18 ALL ABOUT UCONNECT
WHAT IS UCONNECT?
Before you drive, familiarize yourself with the easy-to-use
Uconnect System.
• The Uconnect Voice Command And Uconnect Phone
Buttons On Your Steering Wheel
• The buttons let you use your voice to give commands,
make phone calls, respond to text messages hands-free,
enter navigation destinations and control your radio and
media devices.
1 — Push To MUTE
2 — Push To Initiate Or To Answer A Phone Call, Send Or Receive
A Text
3 — Push To Begin Radio, Media, Navigation, And Climate Functions
4 — Push To End Call
ALL ABOUT UCONNECT 19
3
1
2
3
4
5
6
7
—
—
—
—
—
—
—
Uconnect Phone Hang Up Button
Uconnect Voice Command Button
Steering Wheel Audio Controls (Left)
Uconnect Phone Mute Button
Uconnect Phone Pick Up Button
Steering Wheel Audio Controls (Right)
Volume Knob
8 — Eject Button
9 — CD Slot
10 — Uconnect Radio
11 — SETTINGS Button
12 — Tune/Scroll Knob/Browse/Enter Button
13 — USB Port (Charging Only)
20 ALL ABOUT UCONNECT
WARNING!
Uconnect 5.0/5.0 NAV
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
IDENTIFYING YOUR RADIO
There are a few quick ways for you to identify your radio.
For a more complete description, please refer to the User
Guide in your glove box or visit DriveUconnect.com.
Uconnect 5.0/5.0 NAV features:
• 5” Touchscreen
• Hands-free/Bluetooth
• SiriusXM Satellite Radio (If Equipped)
• Navigation — If Equipped
NOTE: If equipped with a Uconnect 5.0, the Navigation
button on the faceplate will be replaced with a Trip button.
RADIO MODE
CONTENTS
䡵 RADIO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . .22
▫ Setting Presets . . . . . . . . . . . . . . . . . . . . . . . . . .23
▫ Volume & Mute . . . . . . . . . . . . . . . . . . . . . . . . .22
▫ SiriusXM Satellite Radio Mode — If Equipped . . .24
▫ Enter/Browse & Tune/Scroll Control . . . . . . . . . .22
▫ SiriusXM Premier . . . . . . . . . . . . . . . . . . . . . . .24
▫ Seek Functions . . . . . . . . . . . . . . . . . . . . . . . . .22
▫ Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
▫ Direct Tune . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4
22 RADIO MODE
RADIO MODE
Fast Seek Up
Volume & Mute
Press and hold the “Seek Up”
button to advance the
radio through the available stations or channels at a
faster rate, the radio stops at the next available station or
channel when the button is released.
Rotate the rotary knob to adjust the Volume. When the
audio system is turned on, the sound will be set at the same
volume level as last played.
Push the MUTE button to mute the system. Push the
MUTE button again to unmute the system.
Enter/Browse & Tune/Scroll Control
Turn the rotary TUNE/SCROLL control knob clockwise to
increase or counterclockwise to decrease the radio station
frequency.
Seek Functions
Seek Up
Press and release the “Seek Up”
button to tune the
radio to the next listenable station or channel.
During a Seek Up function, if the radio reaches the starting
station after passing through the entire band two times, the
radio will stop at the station where it began.
Seek Down
Press and release the “Seek Down”
button to tune the
radio to the next listenable station or channel.
During a Seek Down function, if the radio reaches the
starting station after passing through the entire band two
times, the radio will stop at the station where it began.
Fast Seek Down
Press and hold the “Seek Down”
button to advance the
radio through the available stations or channel at a
faster rate, the radio stops at the next available station or
channel when the button is released.
RADIO MODE 23
Direct Tune
If you accidently entered the wrong station number, press
the “CLR” button to clear the radio station numbers and
re-enter the correct station number.
Once the last digit of a station has been entered, the Direct
Tune touchscreen will close and the system will automatically tune to that station. The selected Station or Channel
number is displayed in the Direct Tune text box.
Setting Presets
The Direct Tune touchscreen is available in AM, FM and
SXM — If Equipped radio modes and can be used to direct
tune the radio to a desired station or channel. Press the
“Tune” button located at the bottom of the radio screen.
Press the available number button to begin selecting a
desired station. Once a number has been entered, any
numbers that are no longer possible (stations that cannot
be reached) will become deactivated/grayed out.
The Presets are available for all Radio Modes, and are
activated by pressing any of the four “Preset” buttons,
located at the top of the screen.
4
24 RADIO MODE
When you are receiving a station that you wish to commit
into memory, press and hold the desired numbered button
for more that two seconds or until you hear a confirmation
beep.
The Radio stores up to 12 presets in each of the Radio modes.
Four presets are visible at the top of the radio screen.
Pressing the “All” button on the radio home screen will
display all of the preset stations for that mode.
SiriusXM Satellite Radio Mode — If Equipped
SiriusXM Satellite Radio uses direct satellite-to-receiver
broadcasting technology to provide clear, coast to coast
radio content. SiriusXM is a subscription based service.
SiriusXM Premier
Get over 160 channels on your satellite radio, and enjoy all
you want, all in one place. Hear commercial-free music plus
sports, news, talk and entertainment. Get all the premium
programming, including Howard Stern, every NFL game,
Oprah Radio, every MLB and NHL game, every NASCAR
race, Martha Stewart and more. And get 20+ extra channels,
including SiriusXM Latino, offering 20 channels of commercial free music, news, talk, comedy, sports and more dedicated to Spanish language programming.
SiriusXM services require subscriptions, sold separately
after the 12-month trial included with the new vehicle
purchase. If you decide to continue your service at the
end of your trial subscription, the plan you choose will
automatically renew and bill at then-current rates until
you call SiriusXM at 1-866-635-2349 to cancel. See
SiriusXM Customer Agreement for complete terms at
www.siriusxm.com. All fees and programming subject to
change. Our satellite service is available only to those at
least 18 and older in the 48 contiguous USA and D.C.
Our Sirius satellite service is also available in PR (with
coverage limitations). Our Internet radio service is available throughout our satellite service area and in AK and
HI. © 2016 SiriusXM Radio Inc. Sirius, XM and all related
marks and logos are trademarks of SiriusXM Radio Inc.
Service available in Canada; see www.siriusxm.ca.
This functionality is only available for radios equipped
with a Satellite receiver. To receive satellite radio, the
vehicle needs to be outside with a clear view to the sky.
If the screen displays Acquiring Signal, you may need to
change the vehicle’s position to receive a signal. In most
cases, the satellite radio does not receive a signal in
underground parking garages or tunnels.
RADIO MODE 25
Audio
Equalizer
Press the “Equalizer” button to adjust the Bass, Mid and
Treble. Use the “+” or “–” buttons to adjust the equalizer to
your desired settings. Press the “back arrow” button when
completed.
4
1. Push the SETTINGS button located on the faceplate.
2. Then scroll down and press the “Audio” button located
on the touchscreen to open the Audio menu.
3. The Audio Menu displays the following options for you
to customize your audio settings.
Balance/Fade
Press the “Balance/Fade” button to adjust the sound from
the speakers. Use the “arrow” button to adjust the sound
level from the front and rear or right and left side speakers.
Press the Center “C” button to reset the balance and fade to
the factory setting. Press the “back arrow” button when
completed.
26 RADIO MODE
Speed Adjustable
Press the “Speed Adjusted Volume” button to select between OFF, 1, 2 or 3. This will increase the radio volume
relative to a increase in vehicle speed. Press the “back
arrow” button when completed.
Loudness
Press the “Loudness” button to select the Loudness feature.
When this feature is activated it improves sound quality at
lower volumes. Press the “back arrow” button when completed.
Auto On Radio
Press the “Auto On Radio” button to set how the radio
behaves when the Ignition is switched to ON. The options
are: On, Off or Recall Last to the last turned to stop
condition. Press the “back arrow” button when completed.
Radio Off Delay
Press the “Radio Off Delay” button to keep the radio On for
a preset amount of time after the Ignition is switched OFF.
Press the “back arrow” button when completed.
MEDIA MODE
CONTENTS
䡵 MEDIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . .28
▫ USB/iPod Mode . . . . . . . . . . . . . . . . . . . . . . . .30
▫ Common Media Functions . . . . . . . . . . . . . . . . .28
▫ AUX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
▫ Disc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
▫ Bluetooth Mode. . . . . . . . . . . . . . . . . . . . . . . . .31
5
28 MEDIA MODE
MEDIA MODE
Fast Seek Up
Media Mode is entered by pushing the MEDIA button
located on the faceplate. Once in MEDIA mode, press the
“Source” button and the desired mode button. Disc, USB,
AUX and Bluetooth are the Media sources available. You
can select the “Browse” button to be given these options:
• Now Playing
• Songs
Press and hold the “Seek Up”
button and the desired
mode will begin to fast forward through the current
track until the button is released.
• Artists
• Playlists
• Albums
• Folders
• Genres
You can select the “Source” button, “Pause/Play” button or
the “Info” button for artist information on current song
playing.
Common Media Functions
Seek Up
/Down
Press and release the “Seek Up”
button for the next
selection. Press and release the “Left Arrow”
button
to return to the beginning of the current selection, or
return to the beginning of the previous selection if the
Disc, USB, AUX and Bluetooth is within the first eight
seconds (less time for some devices) of the current selection.
Seek Down
Press and release the “Seek Down”
button on the
touchscreen to tune the radio to the next listenable
station or channel.
Fast Seek Down
Press and hold the “Seek Down”
button and the
desired mode will begin to rewind through the current
track until the button is released.
Source
Press the “Source” button to select the desired audio
source, Disc, AUX, USB/iPod or Bluetooth. This screen will
time out after a few seconds and return to the main radio
screen if no selection is made.
Info
Press the “Info” button to display the current track information. Press the “X” button to cancel this feature.
MEDIA MODE 29
Shuffle
Press the “Shuffle” button to play the selections on the
USB/iPod or Bluetooth (if supported) device in random
order to provide an interesting change of pace. Press the
button a second time to turn this feature off.
matically be pulled into the Disc player and the Disc icon
will illuminate on the radio display. If a Disc does not go
into the slot more than 1.0 inch (2.5 cm), a disc may already
be loaded and must be ejected before a new Disc can be
loaded.
Press the ⬙Repeat⬙ button to replay the selection on the
USB/iPod or Bluetooth (if supported) device. Press the
button a second time to turn this feature off.
If you insert a Disc with the ignition ON and the radio ON,
the unit will switch to Disc mode and begin to play when
you insert the Disc. The display will show the track
number, and index time in minutes and seconds. Play will
begin at the start of track one (1).
Audio
Browse
Refer to Operating Instructions – Radio Mode for adjusting
the audio settings.
Press the “Browse” button to scroll through and select a
desired track on the Disc. Press the “Exit” button if you
wish to cancel the browse function.
Repeat
Disc Mode
Disc Mode is entered by either inserting a CD/Disc into the
Disc player above the display or by pushing the MEDIA
button located on the side of the display. Once in MEDIA
mode, press the “Source” button and select Disc.
Inserting Compact Disc
Gently insert one Disc into the Disc player following the
illustration indicated on the player. The Disc will auto-
Eject Button — Ejecting A Disc
Push the EJECT button to eject the Disc. If you have ejected
a Disc and have not removed it within 20 seconds, it will be
reloaded. If the Disc is not removed, the radio will reinsert
the Disc but will not play it.
A Disc can be ejected with the radio and ignition OFF.
5
30 MEDIA MODE
USB/iPod Mode
AUX Mode
USB/iPod Mode is entered by either inserting a USB Jump
Drive or iPod cable into the USB port or by pushing the
MEDIA button located left of the display. Once in MEDIA
mode, press the “Source” button and select USB/iPod.
AUX Mode is entered by inserting a AUX device using a
cable with a 3.5 mm stereo audio jack into the AUX port or
by pushing the MEDIA mode button located below the
display. Once in MEDIA mode, press the “Source” button
and select AUX.
Inserting USB/iPod Device
Gently insert the USB/iPod device into the USB Port. If you
insert a USB/iPod device with the ignition ON, the unit
will switch to USB/iPod mode and begin to play when you
insert the device. The display will show the Artist and Title
name, and index time in minutes and seconds.
Browse
Press the “Browse” button to select Artist, Albums, Genres,
Songs, Playlists or Folders from the USB device only. Once
the desired selection is made, you can choose from the
available media by pressing the button. Press the “Exit”
button if you want to cancel the browse function.
MEDIA MODE 31
Inserting Auxiliary Device
Bluetooth Mode
Gently insert the Auxiliary device cable into the AUX Port.
If you insert a Auxiliary device with the ignition ON, the
unit will switch to AUX mode and begin to play when you
insert the device cable.
Bluetooth Streaming Audio (BTSA) or Bluetooth Mode is
entered by pairing a Bluetooth compatible device containing music, to the Uconnect system.
Controlling The Auxiliary Device
The control of the auxiliary device (e.g., selecting playlists,
play, fast forward, etc.) cannot be provided by the radio;
use the device controls instead. Adjust the volume with the
VOLUME rotary knob, or with the volume of the attached
device.
NOTE: The vehicle radio unit is acting as the amplifier for
audio output from the Auxiliary device. Therefore if the
volume control on the Auxiliary device is set too low, there
will be insufficient audio signal for the radio unit to play
the music on the device.
Before proceeding, the Bluetooth device needs to be paired
through Uconnect Phone to communicate with the
Uconnect System.
NOTE: See the pairing procedure in this manual for further
details.
Once the Bluetooth device is paired to the Uconnect
System, push the MEDIA button. Once in MEDIA mode,
press the “Source” button and select Bluetooth.
5
UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS
CONTENTS
䡵 UCONNECT VOICE RECOGNITION . . . . . . . . . . .34
▫ Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
▫ Introducing Uconnect. . . . . . . . . . . . . . . . . . . . .34
▫ Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
▫ Get Started . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
▫ Voice Text Reply . . . . . . . . . . . . . . . . . . . . . . . .38
▫ Basic Voice Commands. . . . . . . . . . . . . . . . . . . .36
▫ Additional Information. . . . . . . . . . . . . . . . . . . .39
▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
6
34 UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS
UCONNECT VOICE RECOGNITION
Key Features:
• 5.0 inch full color touchscreen display
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
Introducing Uconnect
Start using Uconnect Voice Recognition with these helpful
quick tips. It provides the key Voice Commands and tips
you need to know to control your Uconnect 5.0 system.
• Bluetooth Connectivity
• Hands Free Uconnect Phone
• Two buttons on either side of the touchscreen display
UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS 35
Get Started
1. Visit UconnectPhone.com to check mobile device and
feature compatibility and to find phone pairing instructions.
2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition.
3. Speak clearly at a normal pace and volume while facing
straight ahead. The microphone is positioned on the
rearview mirror and aimed at the driver.
4. Each time you give a Voice Command, you must first
push either the VR or PHONE button, wait until after
the beep, then say your Voice Command.
5. You can interrupt the help message or system prompts
by pushing the VR or PHONE button and saying a Voice
Command from current category.
All you need to control your Uconnect system with your
voice are the buttons on your steering wheel.
6
1 — Push
2 — Push
A Text
3 — Push
4 — Push
To MUTE
To Initiate Or To Answer A Phone Call, Send Or Receive
To Begin Radio, Media And Navigation Functions
To End Call
36 UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS
Basic Voice Commands
Radio
The basic Voice Commands below can be given at any
point while using your Uconnect system.
Use your voice to quickly get to the AM, FM or SiriusXM
Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.)
Push the VR button
. After the beep, sayѧ
• Cancel to stop a current voice session
• Help to hear a list of suggested Voice Commands
• Repeat to listen to the system prompts again
Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen.
Push the VR button
. After the beep, sayѧ
• Tune to ninety-five-point-five FM
• Tune to Satellite Hits 1
TIP: At any time, if you are not sure of what to say or want
and say
to learn a Voice Command, push the VR button
“Help.” The system will provide you with a list of
commands.
UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS 37
• Change source to USB
• Play artist Beethoven; Play album Greatest Hits; Play
song Moonlight Sonata; Play genre Classical
TIP: Press the “Browse” button on the touchscreen to see
all of the music on your iPod or USB device. Your Voice
Command must match exactly how the artist, album, song
and genre information is displayed.
6
Media
Uconnect offers connections via USB, SD, Bluetooth and
Auxiliary ports (If Equipped). Voice operation is only
available for connected USB and iPod devices. (Remote CD
player optional and not available on all vehicles.)
. After the beep, say one of the
Push the VR button
following commands and follow the prompts to switch
your media source or choose an artist.
• Change source to Bluetooth
• Change source to iPod
38 UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS
Phone
Making and answering hands-free phone calls is easy with
Uconnect. When the Phonebook button is illuminated on
your touchscreen, your system is ready. Check
UconnectPhone.com for mobile phone compatibility and
pairing instructions.
Push the PHONE button
the following commands:
. After the beep, say one of
• Call John Smith
• Dial 123-456-7890 and follow the system prompts
• Redial (call previous outgoing phone number)
• Call back (call previous incoming phone number)
TIP: When providing a Voice Command, push the PHONE
and say “Call,” then pronounce the name
button
exactly as it appears in your phone book. When a
contact has multiple phone numbers, you can say “Call
John Smith work.”
Voice Text Reply
Uconnect will announce incoming text messages. Push the
PHONE button
and say Listen. (Must have compatible mobile phone paired to Uconnect system.)
1. Once an incoming text message is read to you, push the
PHONE button
. After the beep, say... “Reply.”
2. Listen to the Uconnect prompts. After the beep, repeat
one of the pre-defined messages and follow the system
prompts.
UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS 39
PRE-DEFINED VOICE TEXT REPLY
Yes.
Stuck in traffic.
No.
Start without
me.
Okay.
Where are you?
Call me.
Are you
there yet?
I’ll call you later.
I need
directions.
I’m on my way.
Can’t talk
right now.
I’m lost.
RESPONSES
See you later.
I’ll be late.
I will be
<number>
minutes late.
See you in
<number> of
minutes.
Thanks.
TIP: Your mobile phone must have the full implementation of the Message Access Profile (MAP) to take
advantage of this feature. For details about MAP, visit
UconnectPhone.com. Apple iPhone iOS6 or later supports
reading incoming text messages only.
Additional Information
© 2016 FCA US LLC. All rights reserved. Mopar and
Uconnect are registered trademarks and Mopar Owner
Connect is a trademark of FCA US LLC. Android is a
trademark of Google Inc. SiriusXM and all related marks
and logos are trademarks of SiriusXM Radio Inc. Yelp,
Yelp logo, Yelp burst and related marks are registered
trademarks of Yelp.
DriveUconnect.com
Uconnect System Support 1-877-855-8400
Mon. – Fri., 7:00 am – 12:00 am, ET
Sat., 8:00 am – 10:00 pm, ET
Sun., 9:00 am – 5:00 pm, ET
Uconnect Access Services Support 1-855-792-4241. Please
have your Uconnect Security PIN ready when you call.
6
UCONNECT PHONE
CONTENTS
䡵 OPERATING UCONNECT PHONE . . . . . . . . . . . .42
▫ Mute (Or Unmute) Microphone During Call. . . . .45
▫ Pairing A Phone . . . . . . . . . . . . . . . . . . . . . . . .43
▫ Transfer Ongoing Call Between Handset And
Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
▫ Start Pairing Procedure. . . . . . . . . . . . . . . . . . . .43
▫ Phonebook Download — Phonebook Transfer
From Mobile Phone . . . . . . . . . . . . . . . . . . . . . .44
▫ SMS Message Reader . . . . . . . . . . . . . . . . . . . . .45
▫ SMS Message Reader Activation/Deactivation . . .45
▫ Making A Phone Call . . . . . . . . . . . . . . . . . . . . .44
▫ SMS Message Options . . . . . . . . . . . . . . . . . . . .46
▫ Receiving A Call — Accept (And End) . . . . . . . . .44
▫ Changing The Volume . . . . . . . . . . . . . . . . . . . .46
7
42 UCONNECT PHONE
WARNING!
ALWAYS drive safely with your hands on the wheel.
You have full responsibility and assume all risks
related to the use of the Uconnect features and
applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
OPERATING UCONNECT PHONE
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
The Uconnect is a voice-activated, hands-free, in-vehicle
communications system with Voice Command Capability
(see Voice Command section).
The Uconnect allows you to dial a phone number with
your mobile phone using simple voice commands.
NOTE:
• The Uconnect requires a mobile phone equipped with
the Bluetooth Hands-Free Profile, Version 1.0 or higher.
For Uconnect customer support:
• U.S. residents - visit UconnectPhone.com or call
1-877-855-8400 (24 hours a day 7 days a week)
• Canadian residents - visit UconnectPhone.com call
1-800-465-2001 (English) or 1-800-387-9983 (French)
Mon. – Fri., 8:00 am – 8:00 pm, ET
Sat., 9:00 am – 5:00 pm, ET
Sun., Closed
• Prior to starting the pairing procedure, ensure all additional Bluetooth devices or phones within the vehicle
have their Bluetooth disabled.
UCONNECT PHONE 43
Pairing A Phone
To use the Uconnect feature, you must first pair your
Bluetooth phone with the Uconnect system. Refer to
UconnectPhone.com for pairing procedure unique to your
phone.
7. During the pairing stage, a screen is displayed indicating the progress of the operation.
1. Activate the Bluetooth on your mobile phone.
8. If the pairing procedure is completed successfully, a
screen is displayed. Press “Yes” to the question to pair the
mobile phone as favorite (the mobile phone will have
priority on all other mobile phones that will be paired
later on). If no other devices are paired, the system will
consider the first associated device as favorite.
2. Push the “PHONE” button on the radio faceplate.
NOTE:
3. If there are not any mobile phones paired with the
system, the display shows a dedicated screen.
• The priority is determined according to the order of
connection for mobile phones which are not set as
favorite. The last phone connected will have the highest
priority.
Start Pairing Procedure
4. Press the “Yes” button to start the pairing procedure
search for the Uconnect device on the mobile phone (if
No is selected, the Phone main screen is displayed).
5. When prompted by the mobile phone, use its keyboard
to enter the PIN code shown on the system display, or
confirm on the mobile phone the PIN displayed.
6. From the Phone screen you can always pair a mobile
phone by pushing the “Settings” button, then press the
“Add Device” button and proceed as described above.
• For more assistance on pairing your phone, contact
Uconnect customer support:
• U.S. residents - visit UconnectPhone.com for phone
compatibility, pairing instructions and details or call
1-877-855-8400
• Canadian residents - visit UconnectPhone.com for
phone compatibility, pairing instructions and details or
call 1-800-465-2001 (English) or 1-800-387-9983 (French)
7
44 UCONNECT PHONE
Phonebook Download — Phonebook Transfer
From Mobile Phone
the previously downloaded phonebook is available for
use.
If equipped and specifically supported by your phone,
Uconnect will ask you if you want to download names
(text names) and number entries from your mobile phone’s
phonebook. Press the “book icon” to begin the phonebook
data download process. Specific Bluetooth Phones with
Phone Book Access Profile may support this feature. See
UconnectPhone.com for supported phones.
• Only the phonebook of the currently connected mobile
phone is accessible.
Download and update, if supported, begins as soon as the
Bluetooth phone connection is made to the Uconnect, for
example, after you start the vehicle.
• This downloaded phonebook cannot be edited or deleted on the Uconnect. These can only be edited on the
mobile phone. The changes are transferred and updated
to Uconnect Phone on the next phone connection.
NOTE:
• A message on the screen may ask for permission to
initiate the phonebook download.
• A maximum of 2,000 entries per phone will be downloaded and updated every time a phone is connected to
the Uconnect.
• Depending on the maximum number of entries downloaded, there may be a short delay before the latest
downloaded names can be used. Until then, if available,
• Both the SIM card and the mobile phone’s phonebook is
downloaded. SIM card phonebook is not part of the
Mobile phonebook. It is possible that the SIM card
phonebook may not be downloaded depending on the
mobile phone and the phone’s software.
Making A Phone Call
Push the “Phone Pick-up” button
on the steering wheel.
After the BEEP, say “dial” a number (or “call” a name).
Receiving A Call — Accept (And End)
When an incoming call rings, or is announced on Uconnect,
push the “Phone Pick-up” button.
UCONNECT PHONE 45
To end a call, push the “Phone Hang-up” button on the
steering wheel or the “Answer” button on the radio touchscreen.
Mute (Or Unmute) Microphone During Call
During a call, push the “Voice Command” button
the steering wheel.
on
After the BEEP, say “mute” to mute the microphone (or
“mute off” to un-mute the microphone).
Transfer Ongoing Call Between Handset And
Vehicle
During a call, push the “Voice Command” button.
After the BEEP, say “transfer call.”
SMS Message Reader
The system can read the messages received by the mobile
phone.
To use this function, the mobile phone must support the
SMS exchange function via Bluetooth.
If this function is not supported by the phone, the corresponding
button is deactivated (greyed out).
When a text message is received, the display will show a
screen where the options “Listen,” “Call” or “Ignore” can
be selected.
button to access the list of SMS messages
Press the
received by the mobile phone (the list displays a maximum of 60 messages received).
SMS Message Reader Activation/Deactivation
The SMS message automatic reading function can be
activated/deactivated by pressing the corresponding button on the display, which is shown after pressing the phone
selection button.
NOTE: On some mobile phones, to make the SMS voice
reading function available, the SMS notification option on
the phone must be enabled: this option is usually available
on the phone, in the Bluetooth connections menu for a
device registered as Uconnect. After enabling this function
on the mobile phone, it must be disconnected and reconnected with the system to make it effective.
7
46 UCONNECT PHONE
SMS Message Options
Pre-set SMS messages are stored in the system and can be
sent to answer a received message or as a new message.
When an SMS is received, the system also allows the
message itself to be forwarded.
Changing The Volume
During a phone call, use the radio VOLUME rotary knob to
adjust the volume to a comfortable level while the
Uconnect system is speaking. Please note the volume
setting for Uconnect is different than the audio system.
MORE BUTTON
CONTENTS
䡵 MORE MAIN MENU . . . . . . . . . . . . . . . . . . . . . .48
▫ Trip Computer. . . . . . . . . . . . . . . . . . . . . . . . . .48
▫ Compass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
▫ Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
8
48 MORE BUTTON
MORE MAIN MENU
Trip Computer
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
Push the MORE button on the faceplate to display the
More Main Menu. The More Main Menu contains the
following options:
Compass
Show the Compass in full screen mode.
Press the “Trip” button located on the touchscreen to
display the trip information of the vehicle.
This function allows you to display the consumption levels
and define two separate trips called Trip A and Trip B for
monitoring the vehicle’s complete journey in a similarly
independent manner.
Both functions can be reset (reset - start of a new journey):
To reset the desired Trip hold down the Trip A or Trip B
buttons.
Clock
Show the Clock in full screen mode.
NAVIGATION
CONTENTS
䡵 NAVIGATION (UCONNECT 5.0N) —
IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . . . . .50
▫ Read Me First . . . . . . . . . . . . . . . . . . . . . . . . . .50
9
50 NAVIGATION
NAVIGATION (UCONNECT 5.0N) — IF EQUIPPED
Read Me First
Switching On
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
To access the navigation, push the “NAV” button.
Setting Up
When you first switch on navigation, you have to answer a
few set-up questions. Answer the questions by pressing the
touchscreen.
GPS Reception
When you first start TomTom navigation, the system may
need a few minutes to determine your GPS position and
show your current position on the map. In the future, your
position will be found much faster, usually within a few
seconds.
Large objects such as tall buildings can sometimes interfere
with GPS reception.
The Update Portal
The Update Portal will be used for updating the content of
your navigation system.
Please refer to your dealer for more information on the
content update procedure.
NAVIGATION 51
Safety Settings
We recommend using the safety settings to make your
driving as safe as possible.
These are some of the options included in the safety
settings:
• Show safety reminders.
• Warn when driving faster than allowed.
You can also drive more safely by using voice commands to
control navigation.
Getting Help To Use Your Navigation System
2. Press the “Drive to” button on the touchscreen.
You can get further help by going to
http://us.support.tomtom.com/app/results.
3. Press the “Address” button.
Planning A Route
To plan a route, do the following:
1. Press the touchscreen to open the Main Menu.
You can change the country or state setting by pressing
the state icon in the upper right corner of the screen.
4. Enter the town or city name, or the ZIP code.
Towns with similar names are shown in the list while
you type.
9
52 NAVIGATION
NOTE: Press the “Arrow” button to the right of the list to
expand the list of suggested towns.
When the correct city or town appears in the list, press the
name to select the destination.
6. Enter the house number, then press the “OK” button.
5. Enter the street name.
Streets with similar names are shown in the list while
you type.
When the correct street name appears in the list, press
the name to select the destination.
NAVIGATION 53
7. The location is shown on the map. Press the “Select”
button to continue or press the “Back” button to enter
another address.
8. When the new route is shown, press the “Done” button.
NOTE: If you want your final destination to be a parking
lot, press the “Parking lot” button and select a location
from the list of parking lots close to your general destination.
To change your route, for example, to travel via a
particular location or to select a new destination, press
the “Change route” button.
For more information about the route, press the “Details”
buttons.
9
You are guided to your destination using spoken instructions and on-screen directions.
54 NAVIGATION
Safety Mode
The navigation SW will switch to “Safety Mode,” with a
dedicated menu structure, when driving above a threshold
speed of 5 mph (8.0 km/h). In this mode, only that
functionality is available that can be used safely when
driving. The main menu in Safety mode is displayed.
In Safety Mode, it is only possible to enter destinations that
do not require the use of the typewriter.
Route Summary
In Safety mode, you can enter a destination (without the
use of typewriter, see below), go into map display, and
toggle three settings. The “Navigate to” submenu in Safety
Mode has reduced functionality:
The route summary shows an overview of your route, the
remaining distance to your destination and the remaining
estimated journey time.
NAVIGATION 55
To view the route summary, push the right-hand panel on
the status bar in the Driving view or press the “View route”
button in the Main Menu and then press the “Show route
summary” button.
The types of route you can choose from are as follows:
• Every Time I Plan — Will ask you the type of route you
want to plan.
Selecting A Route Type
Every time you plan a route, you can choose to be asked
about the type of route you want to plan.
To do this, push the “Settings” button followed by the
“Route planning,” then “Route types.” Press “Ask me
every time I plan.”
• Fastest Route — Route which takes the least time.
• Eco route — Most fuel-efficient route for your journey.
• Shortest route — Shortest distance between the locations you set. This may not be the quickest route,
especially if the shortest route is through a town or city.
• Avoid motorways — Route which avoids motorways.
9
56 NAVIGATION
Using Arrival Times
You can set your navigation system to ask you if you need
to arrive at a particular time when you plan a route.
Push the “Status bar” button in the
Settings menu, to enable or disable arrival time notifications.
Select how the status bar should be
displayed, then press next.
To enable arrival time notifications, select “Leeway,” then
press “Done.”
After entering a destination, press the “YES” button when
asked about an arrival time to enter a preferred arrival time.
The navigation system calculates your arrival time and
shows you whether you will arrive on time.
You can also use this information to work out when you
need to leave. If route planning shows that you will arrive
30 minutes early, you can wait and leave in 30 minutes
time, rather than arrive early.
Your arrival time is constantly recalculated during your
journey. The status bar shows whether you will arrive on
time or if you are going to be late, as shown below:
You will arrive 55 minutes before the arrival time you entered.
If the estimated arrival time is more than five minutes before the time you entered, it is shown
in green.
You will arrive 3 minutes before the arrival time you entered.
If the estimated arrival time is less than 5 minutes before the time you entered, it is shown in
yellow.
You will arrive 19 minutes late. If the estimated arrival time is later than the time you entered, it
is shown in red.
NAVIGATION 57
Navigation Menu Options
When you press the “Drive to” button you can set your
destination in many ways, not just by entering the address.
The other options are listed below:
Home
Press this button to navigate to your Home location.
You will probably use this button more than any other.
Favorites
Press this button to select a Favorite as your destination.
9
Address
Press this button to enter an address as your destination.
58 NAVIGATION
Recent Destination
Press this button to select your destination from a list of places you have recently used as
destinations.
Point Of Interest
Press this button to navigate to a Point of Interest (POI).
Latitude Longitude
Press this button to enter a destination using latitude and longitude values.
NAVIGATION 59
Position Of Last Stop
Press this button to select your last recorded position as your destination.
Planning A Route In Advance
To plan a route in advance, follow these steps:
You can use your navigation system to plan a route in
advance, selecting your starting point and your destination.
1. Press the touchscreen to bring up the Main menu.
Here are more reasons to plan a route in advance:
• Find out how long a journey is going to take before you
start.
• You can also compare journey times for the same route
at different times of the day or on different days of the
week. Navigation uses IQ Routes when planning a
route. IQ Routes calculates routes based on the real
average speeds measured on roads.
• Study the route of a journey you are planning.
• Check a route for someone who is coming to visit you
and then explain the route to them in detail.
2. Press the “Plan route” button.
This button is shown when no route
has been planned.
9
3. Select the starting point for your journey in the same
way that you would select your destination.
4. Set the destination for your journey.
60 NAVIGATION
5. If Route planning settings are set to “Ask me every time
I plan”, select the type of route you want to plan:
• Fastest route — Route which takes the least time.
• Eco route — Most fuel-efficient route for your journey.
• Shortest route — Shortest distance between the locations you set. This may not be the quickest route,
especially if the shortest route is through a town or
city.
• Avoid motorways — Route which avoids motorways.
6. Choose the date and time that you will make the journey
you are planning.
Navigation uses IQ Routes to work out the best possible
route at that time. This is useful to see how long a
journey takes at different times of the day or on different
days of the week.
Your navigation system plans the route between the two
locations you selected.
Viewing Route Information
You can access these options for the route you last planned
by pressing the “View route” button in the Main Menu or
the “Details” button on the route summary screen.
You can then select from the following options:
Show Instructions
Press this button for a list of all the turn instructions on the route.
This is very useful if you need to explain a route to someone else.
NAVIGATION 61
Show Map Of Route
Press this button to see an overview of the route using the map browser.
Show Route Demo
Press this button to watch a demo of the journey.
You can interrupt the demo at any time by pressing the screen.
Show Route Summary
Press this button to open the route summary screen.
9
62 NAVIGATION
Show Destination
Press this button to see a preview of your destination.
You can navigate to a parking lot near your destination, and view any available information about
your destination, for example, the phone number.
Voice Control
WARNING! (Continued)
About Voice control
Instead of pressing the touchscreen to control your navigation system, you can use your voice to control navigation.
For example, to switch to 2D view, you can say “2D view.”
related to the use of the Uconnect features and applications in this vehicle. Only use Uconnect when it is
safe to do so. Failure to do so may result in an accident
involving serious injury or death.
To view a list of available commands, press the “Help”
button in the Main menu and then press “What can I say?”
The following example shows how to use voice control to
plan a journey to your Home address:
Using Voice Control
1. Push the “Voice Recognition” button on the steering
wheel to turn on the microphone.
You see a screen with examples of commands
you can say.
WARNING!
ALWAYS drive safely with your hands on the wheel.
You have full responsibility and assume all risks
(Continued)
NAVIGATION 63
NOTE: Press the “Help” button in the Main menu then
press “What can I say?” to see a full list of commands you
can say.
The Driving View
2. When you hear a beep, say a command of your choice.
For example, you can say “Navigate home.”
For some phrases, you are asked for confirmation.
NOTE: For the best recognition of what you say, speak
normally without trying to articulate words in an unnatural way. If there is excessive road noise, for example, you
may need to speak in the direction of the microphone.
3. If the command is correct, say “Yes.”
If the command is incorrect, say “No” and repeat the
command after you hear the prompt and tone again.
Your navigation system plans a route from your current
location to your destination.
NOTE: To stop your navigation system from listening out
for further commands, say “Cancel.”
About The Driving View
When your TomTom navigation system starts for the first
time, you are shown the Driving View along with detailed
information about your current position.
Press the center of the touchscreen, at any time, to open the
Main Menu.
9
64 NAVIGATION
The Driving View
4. Road sign information or the next street name.
5. Speed limit, if known
To see the difference between your preferred arrival
time and your estimated arrival time, check the Leeway
checkbox in the Status bar settings.
Press this part of the status bar to switch between a 3D
map and a 2D map.
6. Name of the street you are on
7. Navigation instruction for the road ahead and the
distance to next instruction
1. Zoom button
Press the magnifying glass to show buttons for zooming
in and out.
2. Quick menu
To enable the quick menu, tap Make your own menu in
the Settings menu. If there are only one or two buttons
in your menu, both buttons are shown in the Driving
view.
3. Your current position
If the second instruction is less than 150m after the first
instruction, you see it shown immediately instead of the
distance.
Press this part of the status bar to repeat the last voice
instruction.
8. Remaining journey time, the remaining distance and
your estimated arrival time.
Tap this part of the status bar to open the Route
Summary screen.
To change the information shown in the status bar, tap
Status bar in the Settings menu.
NAVIGATION 65
Driving View Symbols
Using Lane Guidance
Navigation instructions muted
There are two types of lane guidance:
This symbol is shown when the navigation instructions have been muted.
1. Lane images
To hear navigation instructions again, push the middle
panel in the status bar.
Advanced Lane Guidance
About Lane Guidance
NOTE: Lane guidance is not available for all junctions or in
all countries.
Your navigation system helps you prepare for motorway
exits and junctions by showing the correct driving lane for
your planned route.
As you approach an exit or junction, the lane you need is
shown on the screen.
To turn lane images off, push the “Settings” button in
the Main menu, then press “Advanced settings.” Clear
the checkbox for Show lane images.
NOTE: Press anywhere on the touchscreen to return to the
Driving View.
9
66 NAVIGATION
2. Instructions in the status bar
NOTE: If no lane guidance is shown in the status bar and
all lanes are highlighted, you can use any lane.
Changing Your Route
Making Changes To Your Route
After you plan a route, you may want to change the route
or even the destination. There are various ways to change
your route without the need to completely replan the entire
journey.
To change the current route, press the “Change route”
button in the Main menu:
Change Route
Press this button to change the current route.
This button is only shown while there is a planned route.
NAVIGATION 67
Change Route Menu
To change the current route or your destination, press one
of the following buttons:
Change Destination
Press this button to change the current destination.
When you change the destination, you are shown the same options and asked to enter the new
address in the same way as when you plan a new route.
Avoid Roadblock
Press this button while driving on a planned route, to avoid a roadblock or traffic congestion on
the road ahead.
Your navigation system will suggest a new route which avoids the roads on your current route
for the selected distance.
9
Calculate Alternative
Press this button to find an alternative to the current route.
This button is only shown while there is a planned route.
This is a simple way to search for a different route to your current destination.
Your navigation system calculates a new route from your current location, to reach your
destination using completely different roads.
The new route is shown next to the original route so that you can select the route you want to use.
68 NAVIGATION
Travel Via
Press this button to change your route by selecting a location you want to travel past, maybe so
you can meet someone on the way.
When you select a location to travel past, you are shown the same options and asked to enter the
new address in the same way as when you plan a new route.
Your navigation system calculates the route to your destination via the selected location.
The selected location is shown on the map using a marker.
You receive a warning when you reach your destination and when you travel past a marked
location.
Avoid Part Of Route
Press this button to avoid part of the current route.
You are shown a list of the street names on your route.
When you press one of the street names, your navigation system calculates a detour to avoid the
selected street.
The route summary shows both the new route and your original route.
Press the panel on the right to select one of the routes and then press “Done.”
If you do not want to use either of the routes shown in the route summary, press “Change route”
to find another way to change your route.
CAUTION!
When a new route is calculated, you may be asked to
turn off the current road.
NAVIGATION 69
About Waypoints
You can choose to use waypoints for any of the following
reasons:
• You want to travel along a certain road or through a
certain area on the way to your destination.
• You want to make stops before reaching your final
destination.
When you enter a city center as a waypoint, the route
planner will plan a route via the area around this city, not
via the location of the city center. The route planner may
fail to find a route via a city center that has an awkward
location w.r.t. the current route.
Adding The First Waypoint To Your Route
To add the first waypoint to your route, do the following:
1. Press the touchscreen to bring up the Main menu.
2. Press the “Change route” button.
3. Press the “Travel via” button.
NOTE: You can also use Voice control to add Waypoints.
4. Choose the location for your waypoint from a choice of
Home, Favorite, Address, Recent destination, POI,
longitude/latitude, or position of last stop.
On the route summary screen, a message confirms that
the route is being recalculated to include the waypoint.
In the Change route menu, the Travel via button
changes to show that you now have one waypoint on
your current route.
NOTE: The maximum number of waypoints you can add
is three.
Adding Further Waypoints To Your Route
To add more waypoints to your route after the first one has
been added, do the following:
1. Press the touchscreen to bring up the Main menu.
2. Press the “Change route” button.
3. Press the “Travel via” button.
NOTE: You can also use Voice control to add waypoints.
4. Press the “Add” button.
9
70 NAVIGATION
5. Choose the location for your waypoint from a choice of
Home, Favorite, Address, Recent destination, POI,
latitude/longitude or position of last stop.
A message tells you where in the list of waypoints the
new one has been inserted.
6. Press the “Done” button.
On the route summary screen, a message confirms that the
route is being recalculated to include your waypoints.
7. Repeat to add more waypoints.
On the Change route menu, the Travel via button
changes to show that you now have several Waypoints
on your current route.
4. Press the waypoint you want to move up or down.
You will see a touchscreen with the name of your
waypoint at the top.
5. Press the “Move up” or “Move down” buttons.
Your Waypoint changes its position in the list and you
are immediately returned to your list of waypoints.
NOTE: You cannot move an unvisited waypoint into a list
of already visited waypoints.
Deleting A Waypoint
To delete a waypoint, do the following:
1. Press the touchscreen to bring up the Main Menu.
Changing The Order Of Waypoints
2. Press the “Change route” button.
Waypoints are automatically added in an optimized order
but you can still change the order manually if you need to.
To change the order of waypoints, do the following:
3. Press the “Travel via” button.
1. Press the touchscreen to bring up the Main menu.
2. Press the “Change route” button.
3. Press the “Travel via” button.
4. Press the waypoint you want to delete.
You will see a touchscreen with the name of your
waypoint at the top.
5. Press the “Delete” button.
Your waypoint is deleted and you are immediately
returned to your list of waypoints.
NAVIGATION 71
Reactivating A Waypoint
NOTE: You can only reactivate a waypoint that has already
been visited. Visited waypoints are greyed out.
To view the map in this way, press “View map” or “View
route”, then “Show map of route” in the Main menu.
To reactivate a waypoint, do the following:
You view different locations on the map by moving the
map across the screen. To move the map, press the touchscreen and drag your finger across the screen.
1. Press the touchscreen to bring up the Main menu.
View Map
2. Press the “Change route” button.
3. Press the “Travel via” button.
4. Press the visited waypoint that you want to reactivate.
You will see a touchscreen with the name of your
waypoint at the top.
5. Press the “Reactivate” button.
The waypoint is deleted and reinserted into the list of
waypoints that haven’t yet been visited.
9
View Map
About Viewing The Map
You can view the map in the same way as you might look
at a traditional paper map. The map shows your current
location and many other locations such as Favorites and
POIs.
1. Options button
Press this button to show options on the maps such as
Points of Interest (POIs), favorites, or names.
2. Find button
Press this button to find specific addresses, favorites or
Points of Interest.
72 NAVIGATION
3. Zoom bar
Zoom in and out by moving the slider.
Options
Press the “Options” button to set the information shown on
the map and show the following information:
• Names — Select this option to show street and city
names on the map.
• Points of interest — Select this option to show POIs on
the map. Press “Choose POIs” to choose which POI
categories are shown on the map.
• Favorites — Select this option to show your Favorites on
the map.
Sounds And Voices
About Sounds And Voices
Your TomTom navigation system uses sound for some or
all of the following:
• Driving directions
• Warnings that you set
There are two types of voice available when navigating:
1. Computer voices — Computer voices are generated by
your navigation system. They read traffic and voice
command responses.
2. Human voices — These are recorded by an actor and
only provide route instructions.
Changing The Volume Level
You can change the volume for your navigation system on
the main unit.
You can turn navigation instructions on/off by doing the
following:
• In the Driving view — Press the central panel on the
status bar to hear navigation instructions again, if they
were previously muted.
• In the Settings menu — Press the “Settings” button in the
Main menu, then press “Turn on/off voice guidance.”
NAVIGATION 73
Settings
About Settings
You can change the way your navigation system looks and
behaves. Most of the settings on your system can be accessed
by pressing the “Settings” button in the Main Menu.
Use Night Colors
Press this button to display the map in darker colors.
NOTE: Your navigation system can switch between day and night colors depending on the
time of day. To automatically switch between night and day colors, press the “Map colors”
button in the Settings menu and select “Switch to night colors when dark.”
Use Day Colors
Press this button to display the map in brighter colors.
9
74 NAVIGATION
Turn Off Voice Guidance
Press this button to switch off voice guidance. You will no longer hear spoken route instructions
but you will still hear information such as traffic information and warnings.
Voice guidance is also switched off when the main unit volume is muted.
Turn On Voice Guidance
Press this button to switch on voice guidance and hear spoken route instructions.
Voice Settings
Press this button to set the type of spoken directions and other route instructions that your
navigation system will read aloud.
NAVIGATION 75
Make Your Own Menu
Press this button to add up to six buttons to your own personalized menu.
If there are only one or two buttons in your menu, both buttons are shown in the Driving view.
If you have three or more buttons in your menu, then a single button is shown in the Driving view
which opens your menu when pressed.
Favorites
Press this button to add, rename or delete Favorites.
Favorites provide an easy way to select a location without the need to enter the address. They do
not need to be favorite places, they can simply be seen as a collection of useful addresses.
9
76 NAVIGATION
To create a new Favorite, press the “Add” button then enter
the location address in the same way that you enter an
address when you plan a route.
To view or change an existing Favorite, press one of the
items in the list. To see more Favorites on the map, press
the “left or right” buttons.
Home Location
Press this button to set or change your Home location. You enter the address in the same way as
you do when you plan a route.
Your Home location provides an easy way to plan a route to an important location.
For most people, your Home location will be your home address. However, you might prefer to
set the location to another regular destination, such as your workplace.
NAVIGATION 77
Route Planning
Press the “Route planning” button to set the way your navigation system calculates the routes
that you plan.
Press the button for each option to change the settings.
Route Types
Set the type of route you want your navigation system to
calculate.
Toll roads, Ferries, Carpool lanes and Unpaved roads settings
Set how your navigation system should manage each of
these road features when the system calculates a route.
Carpool lanes are sometimes known as High Occupancy
Vehicle Lanes and are not present in every country. To travel
on these lanes, you may need to have more than one person
in the vehicle, for example, or the vehicle may need to use
environmentally-friendly fuel.
Route Summary
Set whether you want the route summary screen to close
automatically after you plan a route. If you select No, then
you will need to press Done to close the route summary
screen every time you plan a route.
Vehicle Symbol
Press this button to select the vehicle symbol that shows your current location in the driving view.
9
78 NAVIGATION
Status Bar
Press this button to select the information you want to see on the status bar:
• Horizontal — Show the status bar at the bottom of the Driving view.
• Vertical — Show the status bar on the right-hand side of the Driving view.
• Maximum speed
• Remaining distance — The distance to your destination.
• Leeway — Tour navigation system shows how late or early you will arrive, compared
with your preferred arrival time that was set when you planned the route.
CAUTION!
CAUTION! (Continued)
• The speed limit is shown next to your current speed.
If you drive faster than the speed limit your speed is
shown in red.
• Information about speed limits is not available for
all roads.
Safety Settings
Press this button to select the safety features you want applied to your navigation.
NAVIGATION 79
Map Colors
Press this button to select the color schemes for day and night map colors for 2D and 3D mode.
Press the “Search” button to search for a color scheme by typing the name.
2D/3D Settings
Press this button to set the default view of the map. To switch between 2D and 3D views while
driving, press the left side of the status bar in Driving View.
It is sometimes easier to view the map from above, such as when navigating a complex road
network.
The 2D view shows a two dimensional view of the map as though viewed from above.
The 3D view shows a three dimensional view of the map as though you are driving through the
landscape.
The following buttons are available:
• In 2D view: rotate map in direction of travel — Press this button so the map is
rotated automatically with the direction you are travelling always at the top.
• Switch to 3D view when following a route — Press this button to show the map
automatically in 3D view when you are following a route.
9
80 NAVIGATION
Switch Map
Press this button to select the map you want to use for route planning and navigation.
Although you can store more than one map on the navigation system, you can only use one map
at a time for planning and navigation.
To switch from the current map to plan a route in another country or region, simply press this
button.
Show POI On Map
Press this button to select the types of Point of Interest (POI) you want to see on the map.
Press the “Show POI” button on the map in the Settings menu.
Select the POI categories you want to be shown on the map.
Press “Search” button and use the keyboard to search for a category name.
Select whether you want POIs to be shown in 2D or 3D views of the map.
Press the “Done” button.
Point of Interest locations are shown on the map as symbols.
NAVIGATION 81
Manage POIs
Press this button to manage your own Point of Interest (POI) categories and locations.
You can set your navigation system to let you know when you are near to selected POI locations.
For example, you could set the navigation system to let you know when you are approaching a
gas station.
You can create your own POI categories and add your own POI locations to these categories.
You can, for example, create a new POI category called Friends. You could then add all your
friends’ addresses as POIs in this new category.
Press the following buttons to create and maintain your own POIs:
• Add POI — Press this button to add a location to one of your own POI categories.
• Warn when near POI — Press this button to set your system to warn you when you
are near selected POIs.
• Delete POI — Press this button to delete a POI.
• Add POI category — Press this button to create a new POI category.
• Delete POI category — Press this button to delete one of your own POI categories.
9
82 NAVIGATION
Units
Press this button to set the units used for navigation features such as route planning.
Keyboard
Press this button to select the keyboards that will be available for your use and the layout of the
Latin keyboard.
You use the keyboard to enter names and addresses, such as when you plan a route or search for
the name of a town or a local restaurant.
GPS Status
Press this button to see the current status of GPS reception on your navigation system.
NAVIGATION 83
Advanced Settings
Press this button to select the following advanced settings:
• Show house number before street name — When this setting is selected, addresses are
shown with the house number followed by the street name, such as 10 Downing Street.
• Show street names — When this setting is selected, street names are shown on the
map in the Driving View.
• Show next street name — When this setting is selected, the name of the next street on
your route is shown at the top of the Driving view.
• Show current street name on map — When this setting is selected, the name of the
street you are on is shown at the bottom of the Driving view.
• Show location preview — When this setting is selected, a graphical preview of your
destination is shown during route planning.
• Enable automatic zooming in 2D view
• Enable automatic zooming in 3D view
Advanced Settings
Press this button to select the following advanced settings:
• Show lane images — When this setting is selected, a graphical view of the road ahead
shows which lane you need when you approach a junction or motorway exit. This feature is not available for all roads.
• Show tips — This setting switches tips on and off.
9
84 NAVIGATION
Me And My Navigation
Press this button to find technical information about your navigation system and to select
whether you want to share information with TomTom.
Reset Factory Settings
Press this button to delete all your personal navigation settings and restore the standard factory
settings to your navigation system.
This is not a software update and will not affect the version of the software application installed
on your system.
This feature deletes all your personal settings! — If you want to keep your personal information
and settings, you should perform a full back up before you reset the navigation system. You can
then restore all your personal information and settings after the reset. This includes items such as
your Home and Favorite locations, your personal menu and your POI categories and POI
locations.
Start-Up
Press this button to change whether or not the consent info question should be asked at every
start-up.
NAVIGATION 85
Navigation Updates
The Navigation maps can be updated
using a USB device to download the most
recent maps. To prepare a USB device to
update a map follow the steps below:
NOTE: To update the map, a USB device that meets the
following requirements must be used:
• 8 GB of free memory
• Use a FAT-32 file system
• The USB device must not be blocked and allow files to
be saved
1. Ensure that the map you are updating is active in the
Navigation system.
2. Select Navigation Updates in the Settings menu.
3. Select “Yes” when asked to prepare a USB device for
downloading updates.
4. Insert a USB device (meeting the requirements shown in
the note below).
Points Of Interest
About Points Of Interest
Points of Interest or POIs are useful places on the map.
Here are some examples:
• Restaurants
• Hotels
NOTE: When the USB device is ready a message will be
displayed that it is safe to remove the USB device.
• Museums
5. Remove the USB device and connect it to a computer.
• Gas stations
An updated map can now be downloaded to the USB
device using the TomToM HOME application on the computer. Refer to www.tomtom.cpm/getstarted to download the TomTom HOME application.
• Parking lots
9
86 NAVIGATION
Creating POIs
8. The POI is created and saved in the selected category.
1. Press the touchscreen to open the Main menu.
Using POIs To Plan Route
2. Press the “Settings” button.
When you plan a route, you can use a POI for the
destination or as a waypoint.
3. Press the “Manage POIs” button.
4. If there are no POI categories or the one you want to use
does not exist, Press the “Add POI” category and create
a new category.
Every POI must be assigned to a POI
category. This means you need to
have created at least one POI category before you can create your first
POI.
You can only add POIs to POI categories you have created.
For more information on creating POI categories, read
“Managing POIs.”
5. Press the “Add POI” button.
6. Select the POI category you want to use for the new POI.
7. Press a button to enter the POI address in the same way
that you plan a route.
The following example shows how to plan a route to a
parking lot in a city:
1. Press the “Drive to” button.
2. Press the “Point of Interest” button.
3. Press the “POI in city” button.
NOTE: The last POI you viewed on your navigation
system is also shown in the menu.
4. Enter the name of the town or city and select it when it
is shown in the list.
5. Press the arrow button to expand the list of POI categories.
NOTE: If you already know the name of the POI you want
to use, you can press the “Search by name” button to enter
the name and select this location.
6. Scroll down the list and press the “Parking lot” button.
NAVIGATION 87
7. The parking lot closest to the city center is shown at the
top of the list.
8. The following list explains the distances shown next to
each POI. How the distance is measured varies depending on how you initially searched for the POI:
• POI near you — Distance from your current location.
• POI in city — Distance from the city center.
• POI near Home — Distance from your Home location.
• POI along route — Distance from your current location.
• POI near destination — Distance from your destination.
2. Select the categories you want to be shown on the map.
3. Press the “Done” button.
4. Select whether you want to see POI locations in 2D and
3D views of the map.
5. Press the “Done” button.
The types of POI you have selected are shown as symbols
on the map.
Setting Warnings For POIs
You can set a warning sound to be played when you
approach a selected type of POI, such as a gas station.
9. Press the name of the parking lot you want to use and
press the “Done” button when the route has been
calculated.
The following example will show how to set a warning
sound to be played when you are 500 yards from a gas
station.
Your navigation system starts to guide you to the
parking lot.
1. Press the “Manage POIs” button and then Warn when
near POI in the Settings menu.
Showing POIs On The Map
2. Scroll down the list and press the “Gas station” button.
You can select the types of POI locations you want to see on
your maps.
NOTE: To remove a warning, press on the category name
and then press the “Yes” button. POI categories which have
been set with a warning have a sound symbol next to the
category name.
1. Press the “Show POI on map” button in the Settings menu.
9
88 NAVIGATION
3. Set the distance as 500 yards and press the “OK” button.
4. Press the “Sound effect” button and then press the
“Next” button.
5. Select the warning sound for the POI and then press the
“Next” button.
6. If you only want to hear the warning when the POI is
directly on a planned route, select “Warn only if POI is
on route”. Then press the “Done” button.
The warning is set for the selected POI category. You
will hear a warning sound when you are 500 yards from
a gas station on your route.
Manage POIs
Press the “Manage POIs” button to manage your POI
categories and locations.
You can set your navigation system to
let you know when you are near to
selected POI locations. In this way you
could, for example, set the navigation
system to let you know when you are
approaching a gas station.
You can create your own POI categories and add your own
POI locations to these categories.
This means you can, for example, create a new POI
category called Friends. You could then add all your
friends’ addresses as POIs in this new category.
Press the following buttons to create and maintain your
own POIs:
• Add POI — Press this button to add a location to one of
your own POI categories.
• Warn when near POI — Press this button to set your
system to warn you when you are near selected POIs.
• Delete POI — Press this button to delete one of your
own POI categories.
• Edit POI — Press this button to edit one of your own
POIs.
• Add POI category — Press this button to create a new
POI category.
• Delete POI category — Press this button to delete one of
your own POI categories.
NAVIGATION 89
Help
About Getting Help
Press the “Help” button in the Main menu to navigate to
emergency services centers and other specialist services.
For example, if you are involved in a vehicle accident, you
could use the Help menu to find the contact details for the
nearest hospital, call them using a phone and tell them
your exact location.
Using Help To Phone A Local Service
To use Help to locate a service center, contact the center by
phone and navigate from your current location to the
center, do the following:
5. Select a center from the list, the nearest is shown at the
top of the list.
Your navigation system shows your position on the map
along with a description of the location. This helps you
explain where you are while making a call.
The phone number is displayed for you to call using a
phone.
6. To navigate your way to the center by vehicle, press the
“Navigate there” button.
Your navigation system starts guiding you to your
destination.
1. Press the screen to show the Main Menu.
2. Press the “Help” button.
3. Press the “Call for help” button.
4. Select the type of service you require, for example,
Nearest hospital.
9
90 NAVIGATION
Help Menu Options
NOTE: In some countries, information may not be available for all services.
Call For Help
Press this button to find the contact details and location of a service center.
Drive To Help
Press this button to plan a driving route to a service center.
Where Am I
Press this button to see your current location on the map.
NAVIGATION 91
What Can I Say
Press this button to see a list of commands you can say when using voice control.
Guided Tours
Press this button to view a selection of guided tours relating to your navigation system.
Safety And Other Guides
Press this button to read a selection of guides, including a First Aid guide.
9
92 NAVIGATION
Favorites
Changing The Name Of A Favorite
About Favorites
To change the name of a Favorite, do the following:
Favorites provide an easy way to select a location without
the need to enter the address. They do not need to be
favorite places, they can simply be seen as a collection of
useful addresses.
1. Press the touchscreen to bring up the Main menu.
Using A Favorite
4. Press the Favorite you want to rename.
2. Press the “Settings” button to open the Settings menu.
3. Press the “Favorites” button.
Use the left and right arrows to choose another Favorite
from your list.
You can use a Favorite as a way of navigating to a place
without having to enter the address. To navigate to a
Favorite, do the following:
5. Press the “Rename” button.
1. Press the touchscreen to bring up the Main menu.
6. Type in the new name and then press the “Done” button.
2. Press the “Drive to” button.
7. Press the “Done” button.
3. Press the “Favorite” button.
Deleting A Favorite
4. Select a Favorite from the list.
To delete a Favorite, do the following:
Your navigation system calculates the route for you.
5. When the route is calculated, press the “Done” button.
Your navigation system immediately starts guiding you to
your destination with spoken instructions and visual instructions on the touchscreen.
1. Press the touchscreen to bring up the Main menu.
2. Press the “Settings” button to open the Settings menu.
3. Press the “Favorites” button.
NAVIGATION 93
4. Press the Favorite you want to delete.
Use the left and right arrows to choose another Favorite
from your list.
5. Press the “Delete” button.
6. Press the “Yes” button to confirm the deletion.
7. Press the “Done” button.
Important Safety Notices And Warnings
Global Positioning System
The Global Positioning System (GPS) is a satellite-based
system that provides location and timing information
around the globe. GPS is operated and controlled under the
sole responsibility of the Government of the United States
of America which is responsible for its availability and
accuracy. Any changes in GPS availability and accuracy, or
in environmental conditions, may impact the operation of
this navigation system. TomTom does not accept any
liability for the availability and accuracy of GPS.
Use With Care
Use of TomTom navigation while driving still means that
you need to drive with due care and attention.
This Document
Great care was taken in preparing this document. Constant
product development may mean that some information is
not entirely up to date. The information in this document is
subject to change without notice.
TomTom shall not be liable for technical or editorial errors
or omissions contained herein, nor for incidental or consequential damages resulting from the performance or use of
this document. This document contains information protected by copyright. No part of this document may be
photocopied or reproduced in any form without prior
written consent from TomTom N.V.
Copyright Notices
© 2016 TomTom. All rights reserved. TomTom and the ⬙two
hands⬙ logo are registered trademarks of TomTom N.V.
or one of its subsidiaries. Please see www.tomtom.com/
en_us/legal/ for warranties and end user license agreements applying to this product.
© 2016 TomTom. All rights reserved. This material is
proprietary and the subject of copyright protection and/or
database rights protection and/or other intellectual property rights owned by TomTom or its suppliers. The use of
9
94 NAVIGATION
this material is subject to the terms of a license agreement.
Any unauthorized copying or disclosure of this material
will lead to criminal and civil liabilities.
Data Source © 2016 TomTom All rights reserved.
The software included in this product contains copyrighted
software that is licensed under the GPL. A copy of that
license can be viewed in the License section. You can obtain
the complete corresponding source code from us for a
period of three years after our last shipment of this product.
For more information, visit http://www.tomtom.com/
en_gb/gpl/ or contact your local TomTom customer support team via us.support.tomtom.com/app/answers/list.
Upon request, we will send you a CD with the corresponding source code.
Linotype, Frutiger and Univers are trademarks of Linotype
GmbH registered in the U.S. Patent and Trademark Office
and may be registered in certain other jurisdictions. MHei
is a trademark of The Monotype Corporation and may be
registered in certain jurisdictions.
17UC5PM-526-AB
Second Edition
Uconnect 5.0/5.0 NAV
Printed in the USA
©2016 FCA US LLC. All Rights Reserved.
Chrysler, Dodge, Jeep, Ram, Mopar and Uconnect are trademarks of FCA US LLC.
FIAT is a registered trademark of FCA Group Marketing S.p.A.,
used under license by FCA US LLC.