HP ROM-Based Setup Utility User Guide

HP ROM-Based Setup Utility User Guide
Abstract
This document details how to access and use the HP ROM-Based Setup Utility that is embedded in the system ROM of all HP
ProLiant Generation 2 through 8 servers (except the HP ProLiant DL580 Gen8 server). All options and available responses are
defined. This document is for the person who installs, administers, and troubleshoots servers and storage systems.
HP Part Number: 761393-001a
Published: October 2015
Edition: 2
© Copyright 2003, 2015 Hewlett-Packard Development Company, L.P.
Notices
Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial
Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under
vendor’s standard commercial license.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Acknowledgements
AMD is a trademark of Advanced Micro Devices, Inc. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft and
Windows are U.S. registered trademarks of Microsoft Corporation.
Contents
1 Introduction...............................................................................................9
Overview................................................................................................................................9
Running RBSU..........................................................................................................................9
Using this guide.....................................................................................................................10
2 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8
servers)......................................................................................................11
RBSU main menu....................................................................................................................11
System Options menu..............................................................................................................12
Serial Port options..............................................................................................................12
Embedded Serial Port....................................................................................................12
Virtual Serial Port..........................................................................................................14
Embedded Serial Port Connector.....................................................................................15
Embedded NICs................................................................................................................16
NIC Personality Options.....................................................................................................17
Advanced Memory Protection..............................................................................................18
USB Options.....................................................................................................................19
USB Control.................................................................................................................20
USB 2.0 Controller........................................................................................................21
USB Boot Support.........................................................................................................22
Removable Flash Media Boot Sequence...........................................................................23
USB Drive Key Enumeration............................................................................................23
Processor Options..............................................................................................................25
No-Execute Memory Protection.......................................................................................26
No-Execute Page Protection............................................................................................27
Intel Virtualization Technology.........................................................................................28
AMD V (AMD Virtualization)..........................................................................................29
Intel Hyperthreading Options..........................................................................................30
Enhanced Processor Core Disable (Intel Core Select)..........................................................31
Processor Core Disable (Intel Core Select) (G7 and Gen8 servers).......................................32
Processor Core Disable (AMD Core Select).......................................................................33
Intel Turbo Boost Technology...........................................................................................33
Intel Turbo Boost Technology (Gen8 servers).....................................................................34
Intel Turbo Boost Technology (G7 servers).........................................................................35
AMD Core Performance Boost.........................................................................................36
Intel VT-d......................................................................................................................37
AMD-Vi (IOMMU).........................................................................................................38
Remote Console Mode.......................................................................................................39
NUMLOCK Power-On State.................................................................................................41
SATA Controller Options (Gen8 servers with SATA controllers)..................................................42
Embedded SATA Configuration.......................................................................................42
Drive Write Cache.........................................................................................................43
HP Smart Array B320i RAID Configuration.......................................................................44
Power Management Options menu...........................................................................................45
HP Power Profile................................................................................................................45
HP Power Regulator............................................................................................................46
Redundant Power Supply Mode...........................................................................................47
Advanced Power Management Options................................................................................48
Intel QPI Link Power Management....................................................................................49
Intel QPI Link Frequency.................................................................................................50
QPI Bandwidth Optimization (RTID).................................................................................51
Contents
3
Minimum Processor Idle Power Core State........................................................................52
Minimum Processor Idle Power Core C6 State...................................................................53
Minimum Processor Idle Power C1e State.........................................................................54
Minimum Processor Idle Power Package State...................................................................55
Minimum Processor Idle Power State................................................................................56
Energy/Performance Bias...............................................................................................57
Maximum Memory Bus Frequency...................................................................................58
Channel Interleaving......................................................................................................59
Memory Interleaving......................................................................................................60
PCI Express Generation 2.0 Support................................................................................61
PCIe Gen 3 Control (for select devices)............................................................................62
Maximum PCI Express Speed..........................................................................................63
Dynamic Power Savings Mode Response..........................................................................64
Collaborative Power Control...........................................................................................65
Power Capping Support.................................................................................................66
ACPI SLIT Preferences.....................................................................................................67
DIMM Idle Power Saving Mode......................................................................................68
DIMM Voltage Preference...............................................................................................69
Memory Power Savings Mode........................................................................................70
HyperTransport Frequency..............................................................................................71
Dynamic Power Capping Functionality.............................................................................72
PCI IRQ Settings menu............................................................................................................73
PCI Device Enable/Disable menu.............................................................................................74
Standard Boot Order (IPL) menu...............................................................................................75
Boot Controller Order menu.....................................................................................................76
Date and Time menu...............................................................................................................77
Server Availability menu..........................................................................................................78
ASR Status........................................................................................................................78
ASR Timeout......................................................................................................................79
Thermal Shutdown.............................................................................................................80
Wake-On LAN..................................................................................................................81
POST F1 Prompt................................................................................................................82
Power Button.....................................................................................................................83
Automatic Power-On (G7 servers).........................................................................................84
Automatic Power-On (Gen8 servers).....................................................................................85
Power-On Delay.................................................................................................................86
Server Security menu...............................................................................................................87
Set Power-On Password.......................................................................................................87
Set Admin Password...........................................................................................................88
Network Server Mode........................................................................................................89
Intelligent Provisioning (F10 Prompt)......................................................................................90
Trusted Platform Module......................................................................................................91
TPM Functionality..........................................................................................................91
TPM Visibility................................................................................................................92
TPM Expansion ROM Measuring.....................................................................................93
TPM Clear....................................................................................................................94
BIOS Serial Console & EMS menu............................................................................................95
BIOS Serial Console Port.....................................................................................................96
BIOS Serial Console Baud Rate...........................................................................................97
EMS Console....................................................................................................................98
BIOS Interface Mode..........................................................................................................99
Server Asset Text menu..........................................................................................................100
Server Info Text................................................................................................................100
Administrator Info Text......................................................................................................101
Service Contact Text.........................................................................................................102
4
Contents
Custom POST Message.....................................................................................................103
Advanced Options menu.......................................................................................................104
Advanced System ROM Options........................................................................................104
Option ROM Loading Sequence...................................................................................105
MPS Table Mode........................................................................................................106
ROM Selection...........................................................................................................107
NMI Debug Button......................................................................................................108
Virtual Install Disk........................................................................................................109
PCI Bus Padding Options.............................................................................................110
Memory Mapped I/O Options.....................................................................................111
Address Mode 44-bit...................................................................................................112
Power-On Logo...........................................................................................................113
F11 Boot Menu Prompt.................................................................................................114
Consistent Device Naming...........................................................................................115
Network Boot Retry Support.........................................................................................116
Hide Option ROM Messages........................................................................................117
PCIe Slot6 Training Speed............................................................................................118
Reset on Boot Device Not Found...................................................................................119
HP Option ROM Prompting..........................................................................................120
Video Options.................................................................................................................121
Power Supply Requirements Override..................................................................................122
Thermal Configuration......................................................................................................123
Service Options...............................................................................................................124
Serial Number............................................................................................................124
Product ID..................................................................................................................125
Advanced Performance Tuning Options..............................................................................126
HW Prefetcher............................................................................................................127
Adjacent Sector Prefetch..............................................................................................128
DCU Prefetcher...........................................................................................................129
DCU Streamer Prefetcher..............................................................................................130
DCU IP Prefetcher........................................................................................................131
Data Reuse.................................................................................................................132
Hardware Prefetch training on Software Prefetch.............................................................133
DRAM Prefetch on CPU Request....................................................................................134
DRAM Prefetch on I/O Request.....................................................................................135
CPU Core Hardware Prefetcher.....................................................................................136
CPU Cache Stride Prefetcher.........................................................................................137
Stack Engine Prediction................................................................................................138
Node Interleaving.......................................................................................................139
1333 MHz Support for 3DPC-10600H HP SmartMemory..................................................140
Data Direct I/O..........................................................................................................141
Memory Channel Mode...............................................................................................142
Memory Speed with 2 DIMMs per Channel....................................................................143
Hemisphere Mode......................................................................................................144
HPC Optimization Mode..............................................................................................145
ACPI SLIT Preferences...................................................................................................146
Intel Performance Counter Monitor (PCM).......................................................................146
One Terabyte Memory Limit..............................................................................................148
Drive Write Cache...........................................................................................................149
Asset Tag Protection.........................................................................................................150
SR-IOV...........................................................................................................................151
Embedded SATA RAID......................................................................................................152
System Default Options menu.................................................................................................153
Restore Default System Settings..........................................................................................153
Restore Settings/Erase Boot Disk........................................................................................154
Contents
5
User Default Options........................................................................................................155
Utility Language menu (G5 through G7 servers).......................................................................156
Utility Language menu (Gen8 servers).....................................................................................157
3 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)................158
RBSU main menu..................................................................................................................158
System Options menu............................................................................................................158
Embedded Serial Port A....................................................................................................159
Embedded Serial Port B....................................................................................................160
Virtual Serial Port.............................................................................................................161
Optional LPT Mode Support..............................................................................................161
Integrated Diskette Controller.............................................................................................161
NUMLOCK Power-On State...............................................................................................161
Embedded NICs..............................................................................................................162
Diskette Write Control.......................................................................................................162
Diskette Boot Control........................................................................................................162
Advanced Memory Protection............................................................................................163
USB Control....................................................................................................................164
USB 2.0 EHCI Controller...................................................................................................164
Power Regulator for ProLiant..............................................................................................165
USB External Port Capability.............................................................................................166
Ultra Low Power State.......................................................................................................167
PCI Devices menu.................................................................................................................168
Standard Boot Order (IPL) menu.............................................................................................169
Boot Controller Order menu...................................................................................................170
Date and Time menu.............................................................................................................170
Server Availability menu........................................................................................................170
ASR Status......................................................................................................................171
ASR Timeout....................................................................................................................171
Thermal Shutdown...........................................................................................................171
Wake-On LAN................................................................................................................171
POST Speed Up...............................................................................................................171
POST F1 Prompt..............................................................................................................172
Power Button...................................................................................................................172
Automatic Power-On.........................................................................................................172
Power-On Delay...............................................................................................................172
Server Passwords menu.........................................................................................................172
Set Power-On Password.....................................................................................................173
Set Admin Password.........................................................................................................173
Trusted Platform Module....................................................................................................173
TPM Functionality........................................................................................................174
TPM Visibility..............................................................................................................174
TPM Expansion ROM Measuring...................................................................................174
TPM Clear..................................................................................................................175
Network Server Mode......................................................................................................175
QuickLock.......................................................................................................................175
BIOS Serial Console and EMS menu.......................................................................................175
BIOS Serial Console Port...................................................................................................176
BIOS Serial Console Baud Rate.........................................................................................176
EMS Console..................................................................................................................178
BIOS Interface Mode........................................................................................................179
Server Asset Text menu..........................................................................................................179
Set Server Info Text...........................................................................................................179
Set Administrator Info Text.................................................................................................179
Set Service Contact Text....................................................................................................180
6
Contents
Custom POST Message.....................................................................................................181
Advanced Options menu.......................................................................................................181
Multi-Processor Specification (MPS) Table Mode...................................................................182
ROM Selection................................................................................................................182
Restore Default System Settings..........................................................................................183
Restore Settings/Erase Boot Disk........................................................................................183
User Default Options........................................................................................................183
NMI Debug Button...........................................................................................................184
Virtual Install Disk............................................................................................................184
Secondary IDE Channel Support........................................................................................184
BIOS Enhanced RAID.......................................................................................................184
Node Interleaving............................................................................................................184
Serial Number.................................................................................................................185
Product ID.......................................................................................................................185
Drive Write Cache...........................................................................................................185
SATA Software RAID........................................................................................................185
Optional PCI-X Riser Fan Monitoring...................................................................................185
Processor Options............................................................................................................185
Processor Hyper-Threading...........................................................................................185
HW Prefetcher............................................................................................................186
Adjacent Sector Prefetch..............................................................................................186
No-Execute Memory Protection.....................................................................................186
Intel Virtualization Technology.......................................................................................186
Expansion Card Caching Optimization..........................................................................186
Power Supply Requirements Override..................................................................................186
Embedded VGA Control...................................................................................................187
Utility Language menu...........................................................................................................188
4 RBSU BIOS Serial Console (CLI)................................................................189
BIOS Serial Console/CLI overview..........................................................................................189
BIOS Serial Console setup.....................................................................................................189
Terminal emulation options....................................................................................................189
Microsoft HyperTerminal setup...........................................................................................189
Keystroke emulation..............................................................................................................193
Escape sequences............................................................................................................194
Character translations in VT100 mode...........................................................................194
Inspect CLI Commands..........................................................................................................195
RBSU CLI Commands............................................................................................................196
System Maintenance CLI Commands.......................................................................................198
Command Buffering Support..................................................................................................198
Additional CLI support...........................................................................................................199
5 RBSU configuration flows (manual and scripted).........................................200
RBSU configuration flow overview...........................................................................................200
Manual configuration flow.....................................................................................................200
Scripted configuration flow....................................................................................................200
Configuration Replication Utility (CONREP).........................................................................201
CONREP -s (Store to Data file) .....................................................................................202
CONREP –l (Load from Data File)..................................................................................202
HP ROM Configuration Utility (HPRCU)...............................................................................203
Using HPRCU.............................................................................................................203
HPRCU command-line syntax........................................................................................203
HPRCU command line arguments..................................................................................203
HPRCU return codes....................................................................................................203
Array Configuration Replication Utility................................................................................204
Contents
7
6 ROM-based utilities.................................................................................205
Embedded server setup.........................................................................................................205
Setup Utility....................................................................................................................206
RBSU Erase option......................................................................................................206
Virtual Install Disk option..............................................................................................206
Inspect Utility...................................................................................................................206
Diagnostics Utility............................................................................................................207
Memory Test...............................................................................................................207
CPU Test....................................................................................................................208
Boot Disk Test.............................................................................................................209
Auto-Configuration Process....................................................................................................209
Intelligent Provisioning Quick Configs settings and corresponding RBSU settings............................209
Boot options........................................................................................................................211
Operating System Installation.................................................................................................211
7 Support and other resources....................................................................212
Information to collect before contacting HP...............................................................................212
How to contact HP................................................................................................................212
Subscription service..............................................................................................................212
Related information...............................................................................................................212
Typographic conventions.......................................................................................................213
HP Insight Remote Support.....................................................................................................213
HP Insight Online.................................................................................................................214
8 Documentation feedback.........................................................................215
Acronyms and abbreviations.......................................................................216
Index.......................................................................................................217
8
Contents
1 Introduction
Overview
HP ProLiant Generation 2 through 8 servers (except for the HP ProLiant DL580 Gen8 server) include
a configuration utility that is embedded in the system ROM. This ROM-Based Setup Utility (RBSU)
performs a wide range of configuration activities that may include:
•
Configuring system devices and installed options
•
Displaying system information
•
Selecting the primary boot controller
•
Configuring online spare memory
RBSU is available in two interfaces: a menu-driven interface and a BIOS Serial Command Console
(CLI) interface. Depending on the server model, options in the menu-driven interface vary slightly.
NOTE: Throughout the RBSU menus, the RBSU attempts to display the proper marketing name
for installed PCI devices. If the RBSU does not recognize a device, it assigns a generic label to the
device, such as an Unknown PCI Device. This generic labeling does not affect the functionality
or operation of the device.
Running RBSU
1.
To open the RBSU, reboot the server and press F9 when prompted during the startup sequence.
NOTE:
2.
Modify configuration settings as needed.
•
•
3.
Depending on your environment, the menu-driven or the CLI interface is displayed.
To navigate through and modify settings in the menu-driven interface, use the keystrokes
defined in the following table.
Key
Action
Up or down arrow
Highlight a menu option.
Enter
Select a highlighted menu option.
F1
See online help about a selected submenu option.
Esc
Go back to the previous utility screen.
To modify settings in the CLI, enter the appropriate commands.
When all changes are complete, exit the RBSU and restart the server.
•
To exit the menu-driven RBSU, press Esc until the main menu is displayed. Then, at the
main menu, press F10. The server automatically restarts.
•
To exit the CLI interface, enter the exit command. Then, restart the server.
Overview
9
Using this guide
RBSU is described as follows in this guide:
10
•
Chapter 1: “Introduction” (page 9)
•
Chapter 2: “RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)”
(page 11)
•
Chapter 3: “RBSU menu-driven interface, version 2.xx (G5 and earlier servers)” (page 158)
•
Chapter 4: “RBSU BIOS Serial Console (CLI)” (page 189)
•
Chapter 5: “RBSU configuration flows (manual and scripted)” (page 200)
•
Chapter 6: “ROM-based utilities” (page 205)
Introduction
2 RBSU menu-driven interface, version 3.xx or later (G6,
G7, and Gen8 servers)
NOTE: The RBSU for G6, G7, and Gen8 servers contain many of the same tasks, but some
features differ slightly or are unique offerings dependent on the server model. In this document, if
a feature is unique to a specific server model or processor type, a clarifying note is included in
the section that describes the feature.
The following G6 servers do not use RBSU version 3.xx:
•
DL580 Gen8
•
DL385 G6
•
DL785 G6
•
DL585 G6
For RBSU information for these G6 servers, see “RBSU menu-driven interface, version 2.xx (G5
and earlier servers)” (page 158).
RBSU main menu
In the RBSU main menu, the left-hand side of the screen lists configuration menus and settings to
view or modify. On the right-hand side of the screen, a window displays basic server information,
including the server model, serial number, BIOS version, backup BIOS version, memory installed,
and processors installed.
Each RBSU sub-menu and its options are described in this chapter.
RBSU main menu
11
System Options menu
The System Options menu options control basic I/O server configuration.
Depending on your server model, options may include:
•
“Embedded NICs” (page 16)
•
“NIC Personality Options” (page 17)
•
“Advanced Memory Protection” (page 18)
•
“USB Options” (page 19)
•
“Processor Options” (page 25)
•
“Remote Console Mode” (page 39)
•
“NUMLOCK Power-On State” (page 41)
•
“SATA Controller Options (Gen8 servers with SATA controllers)” (page 42)
•
“HP Smart Array B320i RAID Configuration” (page 44)
Serial Port options
Depending on your server model, options may include:
•
“Embedded Serial Port” (page 12)
•
“Virtual Serial Port” (page 14)
•
“Embedded Serial Port Connector” (page 15)
Embedded Serial Port
The Embedded Serial Port option assigns the logical COM port number and associated default
resources to the selected physical serial port. This setting may be overwritten by the operating
system.
Options include:
•
COM 1 (default for all servers except blades)
•
COM 2 (default for blade servers)
•
COM 3
•
Disabled
NOTE:
12
The COM ports listed and the default setting vary depending on the server model.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
System Options menu
13
Virtual Serial Port
The Virtual Serial Port option assigns the logical COM port number and associated default resources
used by the VSP. The VSP enables the iLO Management Controller to appear as a physical serial
port to support the BIOS Serial Console and the OS serial console.
Options include:
•
COM 1 (default for blade servers)
•
COM 2 (default for all servers except blades)
•
COM 3
•
Disabled
NOTE:
The COM ports listed and the default setting vary depending on the server model.
For more information on iLO configurations, see the iLO user documentation on the Documentation
CD or the HP website (http://www.hp.com/go/ilo/docs).
14
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Embedded Serial Port Connector
NOTE:
This option is available only on some Gen8 servers.
This Embedded Serial Port Connector option controls how the system uses the embedded front
serial port.
Options include:
•
Automatically Switch to SUV Cable (default)—Functions via the front serial port when the SUV
cable is not attached, but automatically switches to the SUV cable if it is attached.
•
Front Serial Port—Disables auto-switching and always have the embedded serial port function
via the front serial port.
System Options menu
15
Embedded NICs
These boot options enable or disable network boot for embedded NICs. These settings provide no
functionality if an embedded NIC is not installed.
NOTE:
•
When enabling Network Boot support for an embedded NIC, the NIC will not show up in the
Standard Boot Order (IPL) until the next reboot.
•
For Gen8 servers, this option is for the embedded LOM or FlexibleLOM.
•
Not every NIC Port is bootable on every FlexibleLOM. Because of this, the RBSU menu may
offer a network boot option that does nothing. To determine which ports are bootable, see
the NIC user documentation.
•
The display differs slightly, based on the number of embedded NICs.
After reading the note message, press any key to display the following settings:
16
•
Network Boot
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
NIC Personality Options
NOTE:
•
This option is supported only on select HP CNA devices.
•
HP Virtual Connect profile settings take precedence over the NIC Personality option settings.
For some systems with a Converged Network Adapter (CNA), the protocols can be configured
using the NIC Personality Options. (CNAs are sometimes referred to as FlexFabric Adapters.) If
an adapter that is supported for use with this option is not present, this menu option does not
appear.
Before configuring protocol settings, certain CNAs require the Network Boot option to be enabled.
If the protocol settings are configured without enabling network boot for these adapters, the protocol
settings may not be saved. After the server reboots and the protocol settings are active, the Network
Boot option can be disabled. For information on enabling network boot, see “Embedded NICs”
(page 16).
Options include:
•
iSCSI (default)
•
FCoE
System Options menu
17
Advanced Memory Protection
Advanced Memory Protection provides additional memory protection beyond ECC (error checking
and correcting), including:
Option
Description
Servers supported
Advanced ECC Support (default)
Provides the largest memory capacity G7 servers: All Gen8 servers: All
to the OS.
Online Spare with Advanced ECC
Support
Enables the system to automatically
G7 servers: All Gen8 servers: All
map out a group of memory that is
receiving excessive correctable
memory errors. This memory is
replaced by a spare group of memory.
Mirrored Memory with Advanced ECC Provides maximum protection against G7 servers: Some models Gen8
Support
uncorrectable memory errors that
servers: Not an available option
would otherwise result in system
failure.
Lockstep Mode with Advanced ECC
Support (Intel servers)
Provides maximum data protection by
enabling multiple-bit memory errors to
be corrected in certain instances not
otherwise possible in Advanced ECC
mode.
G7 servers: Some models Gen8
servers: Not an available option. For
more information about lockstep mode,
see “Memory Channel Mode”
(page 142).
For more information on Advanced Memory Protection, see the HP ProLiant Server Memory website
(http://h18004.www1.hp.com/products/servers/technology/memoryprotection.html).
18
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
USB Options
Depending on your server model, options include:
•
“USB Control” (page 20)
•
“USB 2.0 Controller” (page 21)
•
“USB Boot Support” (page 22)
•
“Removable Flash Media Boot Sequence” (page 23)
•
“USB Drive Key Enumeration” (page 23)
System Options menu
19
USB Control
The USB Control option determines how USB ports and embedded devices operate at startup.
Depending on your server model, options may include the following:
Option
Description
Servers supported
USB Enabled (default)
All USB ports and embedded devices are enabled.
G7 servers: AllGen8 servers:
All
USB Disabled
All USB ports and embedded devices are disabled.
G7 servers: AllGen8 servers:
Not an available option.
NOTE: Disabling USB ports can prevent iLO virtual media
devices from mounting.
Legacy USB Disabled
All USB ports are enabled under a USB-aware OS, but
USB is not supported during POST or RBSU. Legacy USB
Disabled also disables iLO3 virtual devices.
G7 servers: AllGen8 servers:
Not an available option.
External USB Port Disabled
All external USB ports are disabled. Under this option,
embedded USB devices still have full support under the
ROM and OS.
G7 servers: AllGen8 servers:
All
IMPORTANT: Disabling Legacy USB Support removes the ability to use a USB keyboard and
mouse in a pre-boot environment. iLO Virtual Devices used for remote access, including virtual CD,
floppy, keyboard, and mouse are also disabled. RBSU cannot be used to re-enable functionality.
After reading the warning message, press any key to display the available settings.
20
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
USB 2.0 Controller
NOTE:
This option is available on servers with AMD processors.
The USB 2.0 EHCI Controller option is a toggle setting that enables or disables the high-speed
USB 2.0 controller.
Options include:
•
Enabled (default)
•
Disabled
System Options menu
21
USB Boot Support
NOTE:
This option is available on Gen8 servers.
USB Boot Support controls whether the system boots from USB devices connected to the server.
When disabled, this option also disables booting of iLO virtual media.
Options include:
22
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Removable Flash Media Boot Sequence
This option enables the user to select which USB port or SD card slot the system searches first when
enumerating boot devices. The option does not override the device boot order selected in the
Standard Boot Order (IPL) option.
Options include:
•
Internal SD Card First
•
Internal DriveKeys First
•
External DriveKeys First (default)
USB Drive Key Enumeration
By default the BIOS enumerates a USB drive key and treats it as a hard disk. When disabled it is
not enumerated for the device. This only applies to the pre-OS BIOS control of USB.
NOTE: This option is available on HP ProLiant Gen8 servers, except for the HP ProLiant DL580
Gen8 server.
Options include:
•
Enabled (default)
•
Disabled
System Options menu
23
24
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Processor Options
Depending on your server model, options may include:
•
“No-Execute Memory Protection” (page 26)
•
“No-Execute Page Protection” (page 27)
•
“Intel Virtualization Technology” (page 28)
•
“AMD V (AMD Virtualization)” (page 29)
•
“Intel Hyperthreading Options” (page 30)
•
“Enhanced Processor Core Disable (Intel Core Select)” (page 31)
•
“Processor Core Disable (AMD Core Select)” (page 33)
•
“Intel Turbo Boost Technology (Gen8 servers)” (page 34)
•
“Intel Turbo Boost Technology (G7 servers)” (page 35)
•
“AMD Core Performance Boost” (page 36)
•
“Intel VT-d” (page 37)
•
“AMD-Vi (IOMMU)” (page 38)
System Options menu
25
No-Execute Memory Protection
NOTE:
This option is available on servers with Intel processors.
No-Execute Memory Protection enables the hardware portion of a feature that protects systems
against malicious code and viruses. When used in combination with an OS that supports this
feature, certain memory locations are marked as “not for executable code”. Viruses that attempt
to insert and execute code from non-executable memory locations are intercepted and an exception
is raised.
Options include:
•
Enabled (default)
•
Disabled
NOTE: When using hypervisors such as VMware ESX/ESXi and Windows Hyper-V, be sure to
enable this option.
26
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
No-Execute Page Protection
NOTE:
This option is available on servers with AMD processors.
No-Execute Page Protection enables the hardware portion of a feature that protects systems against
malicious code and viruses. When used in combination with an OS that supports this feature,
certain memory locations are marked as not for executable code. Viruses that attempt to insert and
execute code from non-executable memory locations are intercepted and an exception is raised.
Options include:
•
Enabled (default)
•
Disabled
NOTE: When using hypervisors such as VMware ESX/ESXi and Windows Hyper-V, be sure to
enable this option.
System Options menu
27
Intel Virtualization Technology
NOTE:
This option is available on servers with Intel processors.
When enabled, a hypervisor supporting this feature can use extra hardware capabilities provided
by Intel.
Options include:
28
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
AMD V (AMD Virtualization)
NOTE:
This option is available on servers with AMD processors.
When enabled, a hypervisor supporting this feature can use extra hardware capabilities provided
by AMD.
Options include:
•
Enabled (default)
•
Disabled
System Options menu
29
Intel Hyperthreading Options
NOTE:
This option is available on servers with Intel processors.
Intel Hyperthreading Options is a toggle setting that allows Intel Hyperthreading Technology to be
enabled or disabled. Intel Hyperthreading delivers two logical processors that can execute multiple
tasks simultaneously using the shared hardware resources of a single processor core. The option
is supported through the system BIOS.
NOTE: Hyperthreading is not supported on all processors. For more information, see the
documentation for your processor model.
Options include:
30
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Enhanced Processor Core Disable (Intel Core Select)
NOTE:
This option is available on some G7 and Gen8 servers with Intel processors.
The Enhanced Processor Core Disable option allows you to specify the number of cores to enable
per processor socket, in multiples of 2. Unused cores are disabled.
Depending on the applications used, controlling the number of cores to enable has the following
benefits:
•
Reduces processor power usage and improves overall performance
•
Improves overall performance for applications that benefit from higher performance cores
rather than from additional processing cores
•
Addresses issues with software licensed on a per-core basis. Software licensing issues with
enabling or disabling processor core count may exist. For more information, see your software
licensing agreement and user documentation.
After reading the window with additional information about this option, press any key to display
the box in which to enter the number of cores to enable per processor socket.
Options include:
•
All (default)
•
User-defined entry, in multiples of 2
System Options menu
31
Processor Core Disable (Intel Core Select) (G7 and Gen8 servers)
NOTE:
This option is available on some G7 and Gen8 servers with Intel processors.
The Processor Core Disable option allows you to specify the number of cores to enable per processor
socket. Unused cores are disabled.
Depending on the applications used, controlling the number of cores to enable has the following
benefits:
•
Reduces processor power usage and improves overall performance
•
Improves overall performance for applications that benefit from higher performance cores
rather than from additional processing cores
•
Addresses issues with software licensed on a per-core basis. Software licensing issues with
enabling or disabling processor core count may exist. For more information, see your software
licensing agreement and user documentation.
After reading the window with additional information about this option, press any key to display
the box in which to enter the number of cores to enable per processor socket.
Options include:
32
•
All (default)
•
One Core Enabled (on G7 servers)
•
Half Cores Enabled (on G7 servers)
•
User-defined entry, 1–n, where n represents the maximum number of cores for that processor
socket
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Processor Core Disable (AMD Core Select)
NOTE:
This feature is available on G7 and Gen8 servers with AMD processors.
The Processor Core Disable option allows you to specify the number of cores to enable per processor
socket, in multiples of four. Unused cores are disabled.
Depending on the applications used, controlling the number of cores to enable has the following
benefits:
•
Reduces processor power usage and improves overall performance
•
Improves overall performance for applications that benefit from higher performance cores
rather than from additional processing cores
•
Addresses issues with software licensed on a per-core basis. Software licensing issues with
enabling or disabling processor core count may exist. For more information, see your software
licensing agreement and user documentation.
After reading the window with additional information about this option, press any key to display
the box in which to enter the number of cores to leave enabled.
Options include:
•
All (default)
•
User-defined entry, in multiples of 4
Intel Turbo Boost Technology
Intel Turbo Boost Technology enables a processor that has available power headroom and is under
temperature specification to transition to a higher frequency than the rated speed. Disabling this
feature reduces power usage but also reduces the maximum achievable system performance under
some workloads.
System Options menu
33
Intel Turbo Boost Technology (Gen8 servers)
NOTE:
This option is available on Gen8 servers with Intel processors.
Intel Turbo Boost Technology enables a processor that has available power headroom and is under
temperature specification to transition to a higher frequency than the rated speed. Disabling this
feature reduces power usage but also reduces the maximum achievable system performance under
some workloads.
Options include:
34
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Intel Turbo Boost Technology (G7 servers)
NOTE:
This option is available on G7 servers with Intel processors.
Turbo Boost Technology is a processor feature which enables the processor to transition to a higher
frequency than the processor`s rated speed if the processor has available power headroom and
is within temperature specifications. This option enables the customer to customize Turbo Mode
operation based on their platform environment.
Options include:
•
Optimized for Performance (default)—The turbo state can be engaged at any time when
maximum performance is preferred.
•
Optimized for Power Efficiency—The turbo state cannot be engaged until after maximum
performance is needed for an extended period of time.
•
Optimized for Low Power—Low-voltage (LV) DIMMs are configured to operate at 1.35V until
the turbo state is needed. When the turbo state engages, the system BIOS configures the
DIMMs to operate at 1.5V for increased performance.
•
Optimized for Low Power—
•
Disabled
System Options menu
35
AMD Core Performance Boost
NOTE: This option is available on some servers with AMD processors. For more information, see
the documentation for your processor model.
If supported by your processor, AMD Core Performance Boost enables the processor to transition
to a higher frequency than the processor`s rated speed if the processor has available power
headroom and is within temperature specifications. Disabling this feature reduces power usage,
but also reduces the maximum achievable system performance under some workloads.
Options include:
36
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Intel VT-d
NOTE: This option is available on some servers with Intel processors. For more information, see
the documentation for your processor model.
When enabled, a Virtual Machine Manager supporting this feature can use hardware capabilities
provided by the Intel Virtualization Technology for Directed I/O.
Options include:
•
Enabled (default)
•
Disabled
System Options menu
37
AMD-Vi (IOMMU)
NOTE: This option is available on some Gen8 servers with AMD processors. For more information,
see the documentation for your processor model.
When enabled, a Virtual Machine Manager supporting this feature can use hardware capabilities
provided by the AMD I/O Memory Management Unit (IOMMU).
Options include:
38
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Remote Console Mode
NOTE: This option is available only on HP ProLiant ws460c Blade Workstations. It is not available
on other server blades.
The Remote Console Mode option controls whether the system console image is displayed though
an embedded video controller or mezzanine graphics adapter.
Options include:
•
User Mode—Video displays through the embedded video controller during POST, but switches
to the mezzanine graphics adapter for OS boot to display the Windows desktop. In this mode,
the Windows console can only be viewed using remote protocols (for example, using Microsoft
Remote Desktop Connection). Because the embedded video controller is inactive after the
operating system starts, the Windows desktop is not visible on the Local I/O Connector or
through iLO. The screen displays a message stating that the blade is in User Mode.
•
Admin Mode—Video displays through the embedded video controller during POST and OS
boot. In this mode, the mezzanine graphics adapter is disabled.
In Admin Mode, the boot console and the Windows desktop generated by the embedded
video controller can be viewed by using one of the following:
•
◦
A monitor connected to the Local I/O Connector video signal
◦
The iLO Remote Console by pointing your browser to the iLO IP address
◦
Remote desktop connection
Setup Mode—Video is displayed on the embedded video controller during POST and OS
boot. In this mode, the mezzanine graphics adapter is enabled. Setup Mode is similar to
Admin Mode, but in Setup Mode, both the embedded video controller and the mezzanine
graphics adapter are visible to the Windows operating system. Visibility of the mezzanine
graphics adapter enables the Windows operating system to install the mezzanine graphics
adapter driver.
In Setup Mode, the Windows desktop can be viewed by using:
•
◦
A monitor connected to the Local I/O Connector video signal
◦
The iLO Remote Console by pointing your browser to the iLO IP address
◦
Remote desktop connection.
Server Mode—System reverts back to server operation, system and NIC ID's match that of a
server. In this mode, the embedded video controller generates the boot console during POST
and then generates the Windows desktop. The mezzanine graphics adapter is not visible to
any Windows operating systems and is not used.
In Server Mode, the boot console and the Windows desktop generated by the embedded
video controller can be viewed by using:
◦
A monitor connected to the Local I/O Connector video signal
◦
The iLO Remote Console by pointing your browser to the iLO IP address
◦
Remote desktop connection
System Options menu
39
40
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
NUMLOCK Power-On State
NOTE:
This option is not supported on blade servers.
The NUMLOCK Power-On State option is a toggle setting that enables or disables the power-up
state of the NUMLOCK key. When the NUMLOCK key is enabled, it is active when the machine
powers up.
Options include:
•
On
•
Off (default)
System Options menu
41
SATA Controller Options (Gen8 servers with SATA controllers)
NOTE:
These SATA controller options are not supported on BL460, BL465, and DL385 servers)
Depending on your server model, options may include:
•
“Embedded SATA Configuration” (page 42)
•
“Drive Write Cache” (page 43)
•
“HP Smart Array B320i RAID Configuration” (page 44)
Embedded SATA Configuration
NOTE: This option is available only on server models that support Dynamic Smart Array. For
more information, see the HP Dynamic Smart Array RAID Controller User Guide on the HP website
(http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=c03326739).
This option configures the embedded SATA ports, either for optical drives or when connecting
SATA drives directly.
CAUTION:
•
Changing this setting may result in data loss or data corruption on existing drives.
•
Back up all drives before enabling this feature.
•
Enable SATA AHCI support only after consulting the OS documentation to ensure that base
media drivers support this feature.
After the pressing any key to clear the warning, the following options are displayed:
•
Enable SATA Legacy Support
•
Enable SATA AHCI Support
The default setting for this option is dependent on the server model.
42
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Drive Write Cache
IMPORTANT:
•
This option is not visible if SATA SW RAID is enabled.
•
Enabling Drive Write Cache may result in data loss or data corruption if an unexpected power
loss occurs.
Drive Write Cache controls the behavior of the Drive Write Cache in the ATA hard drive. This
feature provides greater drive performance.
After reading the warning message, press any key to display the following settings:
•
Enabled (default)
•
Disabled
System Options menu
43
HP Smart Array B320i RAID Configuration
NOTE: This option is available only on server models that support Dynamic Smart Array. For
more information, see the HP Dynamic Smart Array RAID Controller User Guide on the HP website
(http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=c03326739).
IMPORTANT:
•
Changing this setting may result in data loss or data corruption on existing drives.
•
Back up all drives before enabling this feature.
This option controls HP Dynamic RAID support on the SAS controller (embedded or optionally
purchased on a daughter card).
After reading the warning message, press any key to display the following settings:
•
Enabled
•
Disabled
NOTE:
44
The default setting for this option is dependent on the server model.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Power Management Options menu
The Power Management Options menu includes the following options:
•
“HP Power Profile” (page 45)
•
“HP Power Regulator” (page 46)
•
“Redundant Power Supply Mode” (page 47)
•
“Advanced Power Management Options” (page 48)
NOTE: When using the Intelligent Provisioning Quick Configs options available for Gen8 servers,
you can set a basic policy for performance versus power usage without having to configure
individual settings through RBSU menus. For more information, see “Intelligent Provisioning Quick
Configs settings and corresponding RBSU settings” (page 209).
HP Power Profile
This option enables the user to select the appropriate power profile based on power and
performance characteristics. The following options are available:
•
Balanced Power and Performance (default)—Provides the optimum settings to maximize power
savings with minimal performance impact for most operating systems and applications.
•
Minimum Power Usage—Enables power reduction mechanisms that may affect performance
negatively. This mode guarantees a lower maximum power usage by the system.
•
Maximum Performance—Disables all power management options that may affect performance
negatively.
•
Custom—Provides the opportunity to configure settings for your environment.
Power Management Options menu
45
HP Power Regulator
This feature configures the Power Regulator for ProLiant support.
Options include:
•
HP Dynamic Power Savings Mode (default)—Automatically varies processor speed and power
usage based on processor use, reduces overall power consumption with little or no impact to
performance, and does not require OS support.
•
HP Static Low Power Mode—Reduces processor speed and power usage, guarantees a lower
maximum power usage for the system, and provides a high impact on performance in
environments with higher processor utilization.
•
HP Static High Performance Mode—Processors run in the maximum power and performance
state, regardless of the OS power management policy.
•
OS Control Mode—Processors run in the maximum power and performance state, unless the
OS enables a power management policy.
NOTE: Certain processors support only one power state and operate at their initialized frequency,
regardless of the Power Regulator setting.
After reading the note message, press any key to display the available settings.
46
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Redundant Power Supply Mode
NOTE:
This feature is not available on SL and BL server models.
This feature enables the user to configure how the system manages power delivery to power supplies
in redundant power supply configurations.
Options include:
•
Balanced Mode (default)—Shares the power delivery between all installed power supplies.
NOTE:
Power delivery may not be equal between all power supplies.
•
High Efficiency Mode (Auto)—Delivers full power to one of the power supplies and places the
other power supplies on standby at a lower power-usage level. A semi-random distribution is
achieved, because the Auto option chooses between the odd or even power supply based
on the server's serial number.
•
High Efficiency Mode (Odd Supply Standby)—Delivers full power to the even-numbered power
supplies and places the odd-numbered power supplies on standby at a lower power-usage
level.
•
High Efficiency Mode (Even Supply Standby)—Delivers full power to the odd-numbered power
supplies and places the even-numbered power supplies on standby at a lower power-usage
level.
Power Management Options menu
47
Advanced Power Management Options
Depending on your server model, options may include:
48
•
“Intel QPI Link Power Management” (page 49)
•
“Intel QPI Link Frequency” (page 50)
•
“QPI Bandwidth Optimization (RTID)” (page 51)
•
“Minimum Processor Idle Power Core State” (page 52)
•
“Minimum Processor Idle Power Core C6 State” (page 53)
•
“Minimum Processor Idle Power C1e State” (page 54)
•
“Minimum Processor Idle Power Package State” (page 55)
•
“Minimum Processor Idle Power State” (page 56)
•
“Energy/Performance Bias” (page 57)
•
“Maximum Memory Bus Frequency” (page 58)
•
“Channel Interleaving” (page 59)
•
“Memory Interleaving” (page 60)
•
“PCI Express Generation 2.0 Support” (page 61)
•
“PCIe Gen 3 Control (for select devices)” (page 62)
•
“Maximum PCI Express Speed” (page 63)
•
“Dynamic Power Savings Mode Response” (page 64)
•
“Collaborative Power Control” (page 65)
•
“Power Capping Support” (page 66)
•
“ACPI SLIT Preferences” (page 67)
•
“DIMM Idle Power Saving Mode” (page 68)
•
“DIMM Voltage Preference” (page 69)
•
“Memory Power Savings Mode” (page 70)
•
“HyperTransport Frequency” (page 71)
•
“Dynamic Power Capping Functionality” (page 72)
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Intel QPI Link Power Management
NOTE:
This option is available on servers with multiple Intel processors.
This feature places the Quick Path Interconnect links into a low power state when the links are not
being used. This reduces power usage with minimal performance impact.
Options include:
•
Enabled (default)
•
Disabled
Power Management Options menu
49
Intel QPI Link Frequency
NOTE:
This option is available on Gen8 servers with multiple Intel processors.
This option enables you to set the QPI Link frequency to a low speed. Running at a lower frequency
may reduce power consumption, but may also impact system performance.
Options include:
50
•
Auto (default)
•
Min QPI Speed
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
QPI Bandwidth Optimization (RTID)
NOTE:
This option is available on Gen8 servers with Intel processors.
The QPI link between two processors has been tuned to provide the best performance for all known
applications.
Options include:
•
Balanced (default)—Provides the best performance for nearly all conventional customer
applications and benchmarks.
•
Optimized for I/O—Increases bandwidth from I/O devices such as GPUs that rely on direct
access to system memory. This setting can have a negative effect on system performance.
NOTE: Setting this option to Optimized for I/O can have a negative impact on memory and
system performance.
Power Management Options menu
51
Minimum Processor Idle Power Core State
NOTE:
This option is available on servers with Intel processors.
This feature selects the lowest processor idle power state (C-state) supported by the OS. The higher
the C-state, the lower the power usage of the idle power state. C6 is the lowest power idle state
supported by the processor.
Options include:
52
•
C6 State (default)
•
C3 State
•
C1E State
•
No C-states
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Minimum Processor Idle Power Core C6 State
NOTE:
This option is available on Gen8 servers with AMD processors.
This option enables individual cores of a processor to enter C6 state when the operating system
requests a low power C-State. This state consumes less power and allows other cores in the processor
to enter a higher performance boost state.
Options include:
•
Enabled (default)
•
Disabled
Power Management Options menu
53
Minimum Processor Idle Power C1e State
NOTE:
This option is available on Gen8 servers with AMD processors.
This option enables the processor to enter a reduced power C1e state when all cores of a processor
have entered a low power C-state. Enabling this feature results in substantial power savings in
most configurations.
Options include:
54
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Minimum Processor Idle Power Package State
NOTE:
This option is available on servers with Intel processors.
This feature selects the lowest processor idle power state (C-state). The processor automatically
transitions into package C-states based on the Core C-states that cores on the processor have
transitioned to. The higher the package C-state, the lower the power usage of that idle package
state. Package C6 (non-retention) is the lowest power idle package state supported by the processor.
Options include:
•
Package C6 State (On G7 and earlier servers) / Package C6 (retention) State (On Gen8
servers)
•
Package C3 State (On G7 and earlier servers) (default) / Package C6 (non-retention) State
(On Gen8 servers)
•
No Package State
Power Management Options menu
55
Minimum Processor Idle Power State
NOTE:
This option is available on G7 servers with AMD processors.
This feature selects the lowest processor idle power state (C-state) supported by the OS. The higher
the C-state, the lower the power usage of the idle power state. The lowest power idle state supported
by the processor is C6.
Options may include:
•
C6 State (default)
•
C3 State
•
C1E State
•
No C-states
NOTE:
56
Available options and the system default may vary depending on server model.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Energy/Performance Bias
NOTE:
This option is available on Gen8 servers with Intel processors.
This option configures several processor subsystems to optimize processor performance and power
usage.
Options include:
•
Maximum Performance—Provides the highest performance and lowest latency, but should be
used only in environments that are not sensitive to power consumption.
•
Balanced Performance (default) — Provides the optimum balance between power efficiency
and performance and is recommended for most environments.
•
Balanced Power—Provides optimum power efficiency based on server utilization.
•
Power Savings Mode—Available for use in environments that are power sensitive and are
willing to accept reduced performance.
Power Management Options menu
57
Maximum Memory Bus Frequency
This feature enables you to configure the system to run memory at a lower maximum speed than
what is supported by the installed processor and DIMM configuration. Setting this option to Auto
configures the system to run memory at the maximum speed supported by the system configuration.
Options include:
•
Auto (default)
•
1333MHz
•
1066MHz
•
800MHz
NOTE:
58
Options vary depending on the installed processor.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Channel Interleaving
NOTE:
This option is available on servers with Intel processors.
This feature modifies the level of interleaving for the memory system configuration. Typically, higher
levels of memory interleaving result in maximum performance. However, reducing the level of
interleaving can result in power savings.
Options include:
•
Enabled (default)
•
Disabled
Power Management Options menu
59
Memory Interleaving
This feature modifies the level of interleaving for the memory system configuration. Typically, higher
levels of memory interleaving result in maximum performance. However, reducing the level of
interleaving can result in power savings.
For AMD systems, the following options are available:
•
No Interleaving
•
Channel Interleaving (default)
For Intel systems, the following options are available:
60
•
Full Interleaving (default)
•
Channel Only Interleaving
•
No Interleaving
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
PCI Express Generation 2.0 Support
NOTE:
This option is available on servers with AMD processors.
This feature controls PCIe Generation 1 or PCIe Generation 2 support and can be used to reduce
system power usage. In addition, this feature can be used to work around issues with devices that
claim PCIe 2.0 support but do not adhere to the PCIe 2.0 specification.
Options include:
•
Auto (default)
•
Force PCI-E Generation 2
•
Force PCI-E Generation 1
IMPORTANT: PCIe Generation 1 devices may not function properly when the PCI Express speed
is forced to PCIe Generation 2. Before changing this option, see the QuickSpecs and user
documentation for all expansion cards.
Power Management Options menu
61
PCIe Gen 3 Control (for select devices)
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls the maximum supported speed of individual PCI Express links for embedded
devices and for devices installed in PCIe slots. Enabling PCIe Generation 3 Control permits the
device to fun at full speed.
NOTE: This option works in conjunction with the Maximum PCI Express Speed option. When
setting the PCIe Generation 3 Control to Enabled, the Maximum PCI Express Speed option must
be set to Maximum Supported. For more information about the Maximum PCI Express Speed
option, see “Maximum PCI Express Speed” (page 63).
After selecting the embedded device or PCIe slot to configure, the following options are presented:
62
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Maximum PCI Express Speed
NOTE:
This option is available on Gen8 servers with Intel processors.
This option enables lowering the maximum PCIe speed at which the server allows PCIe devices to
operate and may be useful in addressing issues with problematic PCIe devices. If a PCIe device
does not run properly at its design speed, lowering the speed in which the device is running may
address the problem.
NOTE: This option works in conjunction with the PCIe Gen 3 Control setting. When setting the
PCIe Gen 3 Control to Enabled, this Maximum PCI Express Speed option must be set to Maximum
Supported. For more information about the PCIe Gen 3 Control settings, see “PCIe Gen 3 Control
(for select devices)” (page 62).
Options include:
•
Maximum Supported (default)—Configures the platform to run at the maximum speed supported
by the platform or the PCIe device (whichever is lower).
•
PCIe Generation 1.0—Configures the platform to run at the lowest speed possible in the PCIe
links, which is PCIe Generation 1.0. When setting this option to PCIe Generation 1.0,
performance of high-end cards such as 10GbE NIC Cards and I/O Accelerators may be
affected.
Power Management Options menu
63
Dynamic Power Savings Mode Response
The Dynamic Power Savings Mode Response feature enables the System ROM to control processor
performance and power state depending on the processor workload. This option configures the
response time for switching between these states.
Options include:
64
•
Fast (default)—Optimal for workloads that require a low latency response to an increase in
processor demand.
•
Slow—Optimal for workloads where a longer latency response to increased processing
demand is an acceptable tradeoff for reduced power consumption. Depending on the processor
workload, selecting this option may negatively impact performance.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Collaborative Power Control
NOTE: This option is available on G7 and Gen8 servers with Intel processors and on Gen8
servers with AMD processors.
For operating systems that support the Processor Clocking Control Interface (PCCI), enabling this
option allows the operating system to request processor frequency changes even when the server
has the Power Regulator option configured for Dynamic Power Savings Mode. For operating
systems that do not support the PCC Interface or when the Power Regulator is not configured for
Dynamic Power Savings Mode, this option has no impact on system operation.
Options include:
•
Enabled (default)
•
Disabled
Power Management Options menu
65
Power Capping Support
NOTE:
This option is available on Gen8 servers with Intel processors.
This option applies power cappings if configured via iLO.
Options include:
66
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
ACPI SLIT Preferences
NOTE:
This option is available on Gen8 servers with Intel processors.
ACPI SLIT (System Locality Information Table) describes the relative access times between processors,
memory subsystems, and I/O subsystems. Operating systems that support SLIT can improve
performance by allocating resources and workloads more efficiently.
Options include:
•
Enable
•
Disable (default)
Power Management Options menu
67
DIMM Idle Power Saving Mode
NOTE:
This option is available on select G7 servers.
The DIMM Idle Power Saving Mode option provides the capability to enable or disable power
throttling for the DIMMs installed in the system. Enabling this option allows DIMMs that support
idle power saving features to enter a low power mode when idle. In some applications, this can
reduce overall system power consumption, but may also slightly reduce overall memory performance
due to the increased latency associated with transitions into and out of idle power saving mode.
When disabled, this option prevents installed DIMMs from entering a lower power mode when
idle. Be sure that all installed DIMMs support DIMM idle power saving features before selecting
the Enabled option. Such support has been verified for all HP DIMMs supported on these platforms.
Options include:
68
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
DIMM Voltage Preference
Gen8 systems support both LV-DIMMs (1.35V) and 1.5V-only DIMMs. LV-DIMMs can switch to
1.5V capacity in turbo mode. At 1.35V, they can match the performance of 1.5V DIMMs in most
situations, but in some limited configurations, must switch to 1.5V for maximum speed.
Options include:
•
Optimized for Performance (default)—This sets the voltage for a system with all low voltage
DIMMs to 1.5V only if that provides a performance advantage. Otherwise, the DIMMs are
left at 1.35V.
•
Optimized for Power—Low voltage DIMMs run at 1.35V, even if this requires memory to run
at a lower frequency. The system does not allow 1.35V operation unless all installed DIMMs
in the system are low voltage DIMMs.
Power Management Options menu
69
Memory Power Savings Mode
This option configures several memory parameters to optimize memory performance and power
usage.
Options include:
70
•
Balanced (default)—Provides optimum power efficiency. Recommended for most environments.
•
Maximum Performance —Provides optimum memory performance. This setting should be used
in environments that require the highest performance and/or lowest latency, but are not
sensitive to power consumption.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
HyperTransport Frequency
NOTE:
This option is available on servers with AMD processors.
This option enables you to select the operating speed of the HyperTransport link. Running in HT
power savings mode may result in lower power consumption but may impact overall system
performance.
Power Management Options menu
71
Dynamic Power Capping Functionality
NOTE:
This option is available on Gen8 servers.
This option controls whether the System ROM Power Calibration is run during the boot process.
Options include:
72
•
Enabled (default)—The System ROM Power Calibration is executed during the boot process.
•
Disabled—The System ROM Power Calibration will not be executed during the boot process.
Boot time will be faster, but you will no longer be able to configure Dynamic Power Capping
via iLO.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
PCI IRQ Settings menu
These PCI IRQ options configure the legacy IRQ for embedded and slot-based PCI/PCIe devices.
Multiple devices can share one IRQ.
To change the IRQ assignment for a device, highlight the device and press the Enter key. A menu
is displayed with options to change the IRQ and disable the device.
PCI IRQ Settings menu
73
PCI Device Enable/Disable menu
These options enable and disable embedded and add-in devices. Disabling devices reallocates
the resources (memory, I/O, and, in some cases, option ROM space and power) that would
normally be allocated to the device.
By default, all devices are Enabled.
NOTE: Only IRQs that are modified in RBSU retain the change during the next reboot. IRQs on
PCI devices that have not been modified are subject to change during reboot.
74
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Standard Boot Order (IPL) menu
The Standard Boot Order (IPL) option configures the Initial IPL device and controls the search order
the server uses to look for a bootable device.
NOTE: If you enable or disable a device, restart the server. Changes do not take effect until after
reboot.
The following table describes devices and their default boot order settings.
Device
Default boot order setting
IPL:1 CD-ROM
Set the IPL Device Boot Order to 1
IPL:2 Floppy Drive (A :)
Set the IPL Device Boot Order to 2
IPL:3 USB Drive Key (C :)
Set the IPL Device Boot Order to 3
IPL:4 Hard Drive C :
Set the IPL Device Boot Order to 4
IPL:5 PCI Embedded Adapter Port 1
Set the IPL Device Boot Order to 5
Standard Boot Order (IPL) menu
75
Boot Controller Order menu
The Boot Controller Order option selects which of the installed mass storage device controllers is
used as the primary boot controller. The server attempts to boot the drives attached to each storage
controller in the order presented in this list.
By default, the primary boot controller is set to controller 1.
NOTE: Changes made to the Boot Controller Order in the ORCA Utility are reflected in this menu.
For more information about ORCA, see the Configuring Arrays on HP Smart Array Controllers
Reference Guide on the HP website (http://h20564.www2.hp.com/portal/site/hpsc/public/kb/
docDisplay/?docId=c00729544).
IMPORTANT: PCI devices that have been disabled in the PCI Devices menu might still be visible
on the Boot Controller Order screen.
76
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Date and Time menu
The Date and Time option sets the system time and date. Enter the date in a month-day-year
(mm-dd-yyyy) format. Enter the time in an hour-minute-second (hh:mm:ss) format.
Date and Time menu
77
Server Availability menu
The Server Availability menu includes options that configure the Automatic Server Recovery (ASR)
features:
•
“ASR Status” (page 78)
•
“ASR Timeout” (page 79)
•
“Thermal Shutdown” (page 80)
•
“Wake-On LAN” (page 81)
•
“POST F1 Prompt” (page 82)
•
“Power Button” (page 172)
•
“Automatic Power-On (G7 servers)” (page 84)
•
“Automatic Power-On (Gen8 servers)” (page 85)
•
“Power-On Delay” (page 86)
ASR Status
The ASR Status option is a toggle setting that either enables or disables ASR (Automatic Server
Recovery).
Options include:
78
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
ASR Timeout
The ASR Timeout option sets a timeout limit for resetting an unresponsive server. When the server
has not responded in the selected amount of time, the server automatically resets. The following
time increments are available:
•
10 Minutes (default)
•
15 Minutes
•
20 Minutes
•
30 Minutes
•
5 Minutes
Server Availability menu
79
Thermal Shutdown
The Thermal Shutdown option is a toggle setting that determines when the server automatically
powers down due to dangerous temperatures.
Options include:
80
•
Enabled (default)—The Advanced System Management driver initiates a graceful system
shutdown when the temperature reaches a critical level.
•
Disabled—The Advanced System Management driver ignores thermal events and abruptly
shuts down the system when the temperature reaches a critical level.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Wake-On LAN
The Wake-On LAN option is a toggle setting that enables or disables the Wake-On LAN feature.
When enabled, the server can be powered up remotely using a network controller.
IMPORTANT: When enabling Wake-On LAN, be sure to remove all power cords before adding
or removing any adapters. Some adapters cause the system to power on when they are added or
removed.
After reading the note message, press any key to display the following settings:
•
Enabled
•
Disabled
NOTE:
The default setting varies, depending on the server model.
Server Availability menu
81
POST F1 Prompt
The POST F1 Prompt option is a toggle setting that configures the server so the F1 key must be
pressed to proceed when an error occurs during the power-up sequence. A series of system tests
execute during POST, with errors handled in one of the following ways:
•
If errors occur that allow the system to continue operating, the system continues to boot but
posts a message.
•
If critical components fail or are missing, the server attempts to boot. If it can boot, it posts a
message and an F1 prompt.
•
If the system cannot run with the missing or failed components, it halts until those components
are replaced.
Options include:
82
•
Enabled—If an error occurs during startup, the system stops at the F1 prompt. Boot continues
only after the F1 key is pressed.
•
Disabled—If an error occurs during startup, the F1 prompt is not displayed and the system
continues to boot the OS.
•
Delayed (default)—If an error occurs during startup, the system pauses for 20 seconds at the
F1 prompt and then continues to boot the OS.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Power Button
The Power Button option is a toggle setting that enables or disables the momentary power button.
NOTE: This Power Button feature does not override the 4-second hold-down of the physical server
power button.
Options include:
•
Enabled (default)
•
Disabled
Server Availability menu
83
Automatic Power-On (G7 servers)
NOTE:
This option is not available for blade servers.
The Automatic Power-On feature enables the server to automatically power on when auxiliary
power is applied to the server.
Options include:
84
•
Enabled
•
Disabled (default)
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Automatic Power-On (Gen8 servers)
This feature determines the power state to achieve when power returns to a system that had
experienced an unexpected power outage. Options include:
•
Always Power On—The system returns to the On state when AC power is restored, even if
the system had been in the Off state when power was lost.
•
Always Remain Off—The system returns to the Off state when AC power is restored, even if
the system had been in the On state when power was lost.
•
Restore Last Power State—The system returns to the previous power state (On or Off) when
AC power is restored.
NOTE:
Available options and default values vary depending on server model.
Server Availability menu
85
Power-On Delay
When multiple servers power up after a power loss, the Power-On Delay feature allows you to
delay the server from powering on, to prevent power usage spikes. Pressing the power button,
Wake-on LAN, RTC wake-up, and iLO Virtual Power Button events override any delay setting and
immediately power on the server.
Depending on the system, options may include:
86
•
No Delay (default)
•
Random Delay (up to two minutes)
•
15 Second Delay
•
30 Second Delay
•
45 Second Delay
•
60 Second Delay
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Server Security menu
The Server Security menu includes options that control access to the server and its utilities:
•
“Set Power-On Password” (page 87)
•
“Set Admin Password” (page 88)
•
“Network Server Mode” (page 89)
•
“Intelligent Provisioning (F10 Prompt)” (page 90)
•
“Trusted Platform Module” (page 91)
Set Power-On Password
The Set Power-On Password option sets a password that controls access to the server during
power-up. The server cannot be powered up until the correct password is entered. To disable or
clear the password, enter the password followed by a / (slash) when prompted to enter the
password. To disable or clear the password, enter the password followed by a / (slash) when
prompted to enter the password.
Password requirements:
•
Seven characters maximum.
•
Can be any combination of numbers, letters, and special characters.
Server Security menu
87
Set Admin Password
The Set Admin Password option sets a password to control access to the RBSU and the System
Maintenance Menu during POST. If set, this password must be entered when F9 or F10 is pressed
during POST. To disable or clear the password, enter the password followed by a / (slash) when
prompted to enter the password.
Password requirements:
88
•
Seven characters maximum.
•
Can be any combination of numbers, letters, and special characters.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Network Server Mode
NOTE: This option is available on HP ProLiant DL360 G7, DL380 G7, and DL585 G7 servers.
Gen8 servers do not support Network Server Mode.
The Network Server Mode option is a toggle setting that sets the server to operate in network server
mode. This feature works in conjunction with the power-on password.
When set to Disabled, the server operates normally. When it is set to Enabled, the following actions
occur:
•
The local keyboard remains locked until the power-on password is entered.
•
The power-on password prompt is bypassed.
•
When a diskette is in the diskette drive, the server does not start unless the power-on password
is entered locally.
Options include:
•
Enabled—Disables the server keyboard port.
•
Disabled (default)
IMPORTANT:
established.
Network server mode cannot be enabled until the power-on password has been
Server Security menu
89
Intelligent Provisioning (F10 Prompt)
NOTE:
This option is available on Gen8 servers.
This option controls access to Intelligent Provisioning. When disabled, this option prevents the user
from entering the Intelligent Provisioning environment. This option must be enabled to use Intelligent
Provisioning functionality.
The following methods for accessing Intelligent Provisioning are affected by this RBSU setting:
•
During the server startup process, by pressing F10 when prompted.
•
In the BIOS Serial Console, by pressing ESC+0 when prompted.
•
In the Boot Menu, by selecting the option for a One Time Boot to Intelligent Provisioning.
Options include:
90
•
Enabled (default)—All methods for accessing Intelligent Provisioning are enabled.
•
Disabled—All methods for accessing Intelligent Provisioning are disabled. The prompts are
displayed, but the message indicates that the Intelligent Provisioning function is disabled.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Trusted Platform Module
For servers configured with an optional TPM, the following configuration options are available:
•
“TPM Functionality” (page 91)
•
“TPM Visibility” (page 92)
•
“TPM Expansion ROM Measuring” (page 93)
•
“TPM Clear” (page 94)
IMPORTANT:
TPM menus appear only if the TPM kit is installed.
TPM Functionality
This option controls Trusted Platform Module functionality at startup. Options include:
•
Enabled—Enables the TPM and BIOS secure startup. The TPM is fully functional in this mode.
•
Disabled (default)—Disables the BIOS secure startup but still allows the TPM to be visible to
the operating system. The TPM functionality is limited, but can respond to most commands in
this mode. Selecting Disabled may prevent the server from booting to a TPM-aware operating
system.
CAUTION: A TPM locks all data access if proper procedures are not followed for modifying the
server, including: updating system or option firmware, replacing hardware such as the system
board and hard drive, or modifying TPM OS settings.
For information on installing and enabling the TPM module option, see the user documents for your
server model and the Data security in HP ProLiant servers using the Trusted Platform Module and
Microsoft Windows BitLocker Drive Encryption white paper: http://h20564.www2.hp.com/portal/
site/hpsc/public/kb/docDisplay/?docId=c01681891.
Server Security menu
91
TPM Visibility
The TPM Visibility option provides the ability to hide the TPM from the operating system. Options
include:
92
•
Hide—BIOS secure startup is disabled and the TPM does not respond to any commands from
any software. Hiding the TPM may prevent the server from booting to a TPM-aware operating
system. This option is intended to be used to remove the TPM feature from the system without
removing the actual hardware.
•
Unhide (default)—The TPM is visible to the operating system.
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
TPM Expansion ROM Measuring
TPM Expansion ROM Measuring enables the BIOS to measure the optional PCI or PCIe expansion
ROM code and store that measurement in the TPM. On subsequent reboots, operating systems or
validation software applications that utilize the measurements stored in the TPM can use this data
to detect modifications to PCI or PCIe expansion ROM versions. Options include:
•
Enabled
•
Disabled (default)
Server Security menu
93
TPM Clear
The TPM Clear option allows the user to reset the TPM to factory settings, clearing any assigned
passwords, keys, or ownership data. Options include:
•
Yes, Select to Clear
•
No, Abort Clear (default)
IMPORTANT:
system.
94
Clearing the TPM may prevent the server from booting to a TPM-aware operating
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
BIOS Serial Console & EMS menu
NOTE:
Some languages or characters may require a specific emulation mode.
Through BIOS Serial Console and EMS console redirection, you can view POST error messages
and run RBSU remotely through a serial connection to the server COM port or iLO Virtual Serial
port. The remote server does not require a keyboard or mouse.
For more information about the BIOS Serial Console, see “RBSU BIOS Serial Console (CLI)”
(page 189).
The following menu options are available:
•
“BIOS Serial Console Port” (page 96)
•
“BIOS Serial Console Baud Rate” (page 97)
•
“EMS Console” (page 98)
•
“BIOS Interface Mode” (page 99)
BIOS Serial Console & EMS menu
95
BIOS Serial Console Port
This BIOS Serial Console Port feature controls if and how video and keystrokes are redirected
through the serial port prior to OS startup.
IMPORTANT: This feature may interfere with non-terminal devices attached to the serial port. In
this case, disable the BIOS Serial Console. This feature is not supported under RBSU on Japanese
systems.
Options include:
•
Auto (default for newer servers)—The server checks for the presence of a VT100 compatible
client running at 9600 Baud connected to the server and automatically enables the BIOS
Serial Console if one is found. This eliminates the need to run RBSU with a local keyboard
and monitor attached to enable the BIOS Serial Console feature.
•
Disabled (default for older servers)
•
COM 1
•
COM 2
NOTE: Connect a null modem cable to the serial port/COM port on which BIOS Serial Console
is enabled.
96
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
BIOS Serial Console Baud Rate
The BIOS Serial Console Baud Rate option controls transfer rate at which data is transmitted through
the serial port.
Options include:
•
9600 (default)
•
19200
•
57600
•
115200
BIOS Serial Console & EMS menu
97
EMS Console
The EMS Console option is a Microsoft Windows Server 2003 feature that enables the Emergency
Management Console to be redirected through a specified serial port.
Options include:
•
Disabled (default for all servers except blades)
•
COM1 (default for blade servers)
•
COM2
NOTE:
•
When using iLO, select the value assigned to the Virtual Serial Port (“Virtual Serial Port”
(page 14)).
•
When redirecting EMS through a physical serial port, select the value assigned to the Embedded
Serial Port (“Embedded Serial Port” (page 12)).
EMS provides input/output support for all Microsoft Windows kernel components: the loader,
setup, recovery console, OS kernel, blue screens, and the Special Administration Console. The
Special Administration Console is a text mode management console available after Windows
Server 2003 OS has initialized. For more information on EMS, go to the Microsoft website
(www.microsoft.com).
Microsoft enables EMS in the OS, but EMS must also be enabled in the ROM. When enabled,
EMS assumes the serial port for redirection and may cause interference with other devices attached
to the serial port. To avoid interference, EMS is disabled in the system ROM by default on HP
ProLiant ML and DL servers. If EMS is disabled in Windows Server 2003, perform the following
steps to update the boot.ini file:
1. Enable EMS in RBSU.
2. Run bootcfg/ems on/id 1.
3. Reboot.
98
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
BIOS Interface Mode
This BIOS Interface Mode option determines whether the menu-driven mode or the command line
interface mode is displayed for ROM-based utilities.
Options include:
•
Auto (default)—Enables CLI mode automatically for ROM embedded utilities, if the system
detects a console connection through the serial port instead of the keyboard.
•
Command-Line—CLI mode is always enabled for ROM embedded utilities.
BIOS Serial Console & EMS menu
99
Server Asset Text menu
The Server Asset Text menu includes options that customize the system-specific text for the server.
The following menu options are available:
•
“Server Info Text” (page 100)
•
“Administrator Info Text” (page 101)
•
“Service Contact Text” (page 102)
•
“Custom POST Message” (page 103)
Server Info Text
These options define reference information for the server administrator, which is displayed in Insight
Manager.
•
Server Name—Identifies the server.
•
Server Asset Tag—Identifies the server asset number.
•
Server Primary OS—Describes the primary OS of the server.
•
Other Text—Additional text describing the server.
NOTE: Each of these options can display a maximum of 14 characters. By default, all values
are blank.
100 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Administrator Info Text
These options define reference information for the server administrator, which is displayed in Insight
Manager.
•
Admin Name Text—Defines the server administrator name.
•
Admin Phone Number Text—Defines the server administrator phone number.
•
Admin Pager Number Text—Defines the server administrator pager number.
•
Other Text—Defines additional text relating to the server administrator.
NOTE: The number of characters allowed for each entry varies depending on server model. By
default, all values are blank.
Server Asset Text menu
101
Service Contact Text
These options define reference information for the server administrator, which is displayed in Insight
Manager.
•
Service Name Text—Defines a two-line description for the service contact name.
•
Service Phone Number Text—Defines two lines of text for the service contact phone number.
•
Service Pager Number Text—Defines two lines of text for the service contact pager number.
•
Other Text—Defines two lines of additional text relating to the service contact.
NOTE: The number of characters allowed for each entry varies depending on server model. By
default, all values are blank.
102 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Custom POST Message
The Custom POST Message option enables the user to enter a custom message to display during
POST.
A maximum of 60 characters is supported. By default, this value is blank.
Server Asset Text menu 103
Advanced Options menu
The Advanced Options menu includes the following options:
•
“Advanced System ROM Options” (page 104)
•
“Video Options” (page 121)
•
“Power Supply Requirements Override” (page 122)
•
“Thermal Configuration” (page 123)
•
“Service Options” (page 124)
•
“Advanced Performance Tuning Options” (page 126)
•
“One Terabyte Memory Limit” (page 148)
•
“Drive Write Cache” (page 149)
•
“Asset Tag Protection” (page 150)
“Embedded SATA RAID” (page 152)
NOTE: Menu options may differ from those in this document, depending on specific server
options.
Advanced System ROM Options
•
“Option ROM Loading Sequence” (page 105)
•
“MPS Table Mode” (page 106)
•
“ROM Selection” (page 107)
•
“NMI Debug Button” (page 108)
•
“Virtual Install Disk” (page 109)
•
“PCI Bus Padding Options” (page 110)
•
“Memory Mapped I/O Options” (page 111)
•
“Address Mode 44-bit” (page 112)
•
“Power-On Logo” (page 113)
•
“F11 Boot Menu Prompt” (page 114)
•
“SR-IOV” (page 151)
•
“Consistent Device Naming” (page 115)
•
“Network Boot Retry Support” (page 116)
•
“Hide Option ROM Messages” (page 117)
•
“PCIe Slot6 Training Speed” (page 118)
•
“Reset on Boot Device Not Found” (page 119)
•
“HP Option ROM Prompting” (page 120)
104 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Option ROM Loading Sequence
NOTE:
This option is available on G7 servers.
This feature controls whether the option ROM for embedded devices or expansion boards loads
first. This feature addresses issues such as when the PXE option ROM for the embedded NIC does
not load because of a lack of available option ROM space.
CAUTION:
Changing this option restores the Standard Boot Order (IPL) to the default settings.
After reading the warning message, press any key to display the following settings:
•
Load Option Card Devices First
•
Load Embedded Devices First (default)
Advanced Options menu 105
MPS Table Mode
MPS Table Mode (Multi Processor Specification Table/APIC) is used to interrupt routing. Certain
unsupported operating systems may require disabling the MPS Table.
IMPORTANT: This setting is pre-selected. You can override the default setting at this menu, but
successful OS operation is dependent upon the correct (default) setting.
Options include:
•
Full Table APIC (default)
•
Disabled
106 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
ROM Selection
The ROM Selection option toggles the server ROM between the current ROM and the backup
ROM. This option is supported only on servers with redundant ROMs.
Options include:
•
Use Current ROM (default)
•
Switch to Backup ROM
Advanced Options menu 107
NMI Debug Button
The NMI Debug Button option is a toggle setting that allows you to enable debug functionality
when the system has experienced a software lock-up. The NMI Debug Button generates an NMI
to enable the use of the operating system debugger.
CAUTION: When enabled, pressing the NMI Debug Button on the system board during normal
operation halts the system.
Options include:
•
Enabled (default)
•
Disabled
108 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Virtual Install Disk
This option controls the Virtual Install Disk. The Virtual Install Disk may contain drivers specific to
the server that an operating system may use using installation. When the Virtual Install Disk option
is enabled, Microsoft Windows Server automatically locates required drivers and installs them,
eliminating the need for user intervention and the requirement that a driver be present on external
media during OS installation. In some cases, the Virtual Install Disk remains visible from the installed
OS as a read only drive. During manual installations using Intelligent Provisioning, this feature is
automatically enabled.
To further optimize the system, HP recommends updating boot drivers to the latest versions after
the OS installation.
Options include:
•
•
Enabled—This feature operates differently in Gen8 and G7 environments:
◦
Gen8 environments: Makes visible a read-only virtual disk (256MB)
◦
G7 environments: Makes visible a read-only virtual floppy (1.44MB)
Disabled (default)
NOTE: When Intelligent Provisioning software is updated, this Virtual Install Disk is automatically
updated.
Advanced Options menu 109
PCI Bus Padding Options
This option allows the user to disable the default PCI Bus padding where each expansion slot is
provided with an extra PCI Bus number. By default, the System ROM pads bus numbers for slots
such that adding expansion cards does not affect the bus numbering of devices in the system.
Disabling this option works around issues with certain expansion cards.
HP recommends disabling this option only when you encounter a specific issue.
Options include:
110
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Memory Mapped I/O Options
NOTE:
This option is available only on some G7 servers.
The following menu options allow the user to select the amount of Memory Mapped I/O:
•
2GB of Memory Mapped I/O (default)
•
3GB of Memory Mapped I/O
•
Automatic—The system ROM configures either 2GB or 3GB depending on the amount of
Memory Mapped I/O the system requires.
Advanced Options menu
111
Address Mode 44-bit
NOTE:
This option is available only on DL980 G7 servers.
Enabling this option allows memory to be addressed with 44 bits, allowing for configuration of a
large memory configuration, such as servers with more than 1 TB of memory. Verify that the OS
supports 44-bit addressing capability before enabling this option.
When this option is disabled, some installed memory in the system may not be configured; therefore,
it will not be recognized by the OS. This impact varies depending on the system memory
configuration.
Options include:
112
•
Disabled (default)—only 40-bits are used.
•
Enabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Power-On Logo
This option controls the display of the logo during system boot. This is an aesthetic modification
only and does not affect the system boot times.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
113
F11 Boot Menu Prompt
NOTE:
This option is available on Gen8 servers with Intel processors.
This option allows the disabling of the POST One Time Boot F11 Prompt.
Options include:
114
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Consistent Device Naming
NOTE:
This option is available on Gen8 servers.
This option controls names assigned to devices.
Options include:
•
CDN Support for LOMs only—Embedded NICs and FlexibleLOM (not NICs installed in
expansion slots) are named based on their location in the system
•
Disabled (default)—All NIC ports are named based on their location in the system.
NOTE:
Existing NIC connections retain their names until reinstalled under the OS environment.
Advanced Options menu
115
Network Boot Retry Support
NOTE:
This option is available only on Gen8 servers.
This option controls system logic for retrying a failed network boot when attempting to boot from
an installed network adapter. This option affects only the primary network adapter listed in the
Standard Boot Order (IPL).
For information about what happens to the booting sequence when none of the devices in the IPL
are bootable, see “Reset on Boot Device Not Found” (page 119).
Options include:
•
Enabled (default)—The system attempts to boot from the primary network adapter up to 20
times before trying to boot from the next IPL device.
•
Disabled—If the system cannot boot from the primary network adapter, it immediately tries to
boot from the next IPL device.
For more information about the IPL, see “Standard Boot Order (IPL) menu” (page 75).
116
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Hide Option ROM Messages
NOTE:
This option is available on some G7 and Gen8 and servers with Intel processors.
This option controls the display of F-key prompts during POST.
•
Enabled (default)—Hides all F-key prompts during startup. When enabled, components such
as iLO and Smart Array controllers cannot be configured during POST.
•
Disabled—F-key prompts are displayed during startup.
Advanced Options menu
117
PCIe Slot6 Training Speed
NOTE:
This option is available on some G6 servers with Intel processors.
This option controls PCI express slot 6 only and does not impact the operation of PCIe slots 1-5.
118
•
PCIe Generation 2 (default)
•
PCIe Generation 1
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Reset on Boot Device Not Found
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls the System ROM logic of what happens when bootable devices listed in the
Standard Boot Order (IPL) are not found.
Options include:
•
Enabled— System ROM resets the platform after one attempt through the Standard Boot Order
(IPL).
•
Disabled (default)—System ROM continually loops through the Standard Boot Order (IPL).
Advanced Options menu
119
HP Option ROM Prompting
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls whether HP expansion cards discovered during POST will prompt for user input
to enter expansion card setup utilities.
Options include:
•
Enabled (default)—If unconfigured expansion cards are discovered during POST, the system
will prompt the user, asking whether to open the expansion card setup utility. POST is halted
until you enter a response to the prompt.
•
Disabled—The POST process will not provide a prompt about configuring expansion cards.
120 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Video Options
These options control the video display.
Options include:
•
Optional Video Primary, Embedded Video Disabled (default)—System ROM disables the
embedded video controller when an optional video controller is installed in the system.
•
Optional Video Primary, Embedded Video Secondary—The embedded video controller remains
enabled for iLO remote video functionality. The optional video controller is enabled as the
primary video controller and is used to show text during POST.
•
Embedded Video Primary, Optional Video Secondary—The embedded video controller is
enabled as the primary controller and shows POST text as well as function for iLO remote
video functionality. The secondary controller is enabled for use under an operating system.
NOTE:
•
The ability to support dual-head video between the embedded and a stand up device is
dependent on support from the operating system. For more information, see your operating
system documentation.
•
When multiple optional video cards are installed, the card that is selected as primary is based
on PCI enumeration, which varies depending on the platform. You may have to remove and
reinstall the cards in a different order to control which card is the primary controller.
Advanced Options menu
121
Power Supply Requirements Override
NOTE:
This option is available on HP ProLiant DL580 G7 and DL585 G7 servers.
The option enables overriding the system requirement that, when one or more x16 high-powered
(225W+) PCI Express graphic cards are installed, the system operate on High Line (200-240
VAC). When this option is enabled, the system is allowed to boot and operate even if the system
is operating on Low Line (100-120 VAC).
CAUTION: When Power Supply Requirements Override is enabled, some configurations may
not operate properly. Before enabling this option, verify and understand the system power
requirements.
After reading the warning message, press any key to display the following settings”
•
Default Power Supply Requirements
(default)
122
•
Configure for 1 minimum required, 2 required for redundancy
•
Configure for 2 minimum required, 3 required for redundancy
•
Configure for 2 minimum required, 4 required for redundancy
•
Configure for 3 minimum required, 4 required for redundancy
•
Configure for 4 minimum required, no redundancy
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Thermal Configuration
This feature enables the user to select the fan cooling solution for the system.
Depending on the system, options may include:
•
Optimal Cooling (default)—Provides the most efficient solution by configuring fan speeds to
the minimum required to provide adequate cooling.
•
Increased Cooling—Operates fans at higher speeds to provide additional cooling. Increased
cooling is often chosen to accommodate 3rd party options not listed in the QuickSpecs and
devices that do not report temperature. HP recommends selecting Increased Cooling when a
system is experiencing thermal issues that cannot be resolved in another manner. Larger scale
application of Increased Cooling over multiple systems, especially when in a closed cooling
loop rack, POD, or data center near the limits of its cooling capacity, should study the impact
of such a change prior to implementing it.
•
Maximum Cooling—Provides the maximum cooling available for the platform. (Available only
on Gen8 servers with Intel processors).
Advanced Options menu
123
Service Options
•
“Serial Number” (page 124)
•
“Product ID” (page 125)
Serial Number
The Serial Number option enables service personnel to change the serial number. HP recommends
that you do not change this number unless you are replacing a system board.
IMPORTANT: The serial number should be modified by qualified service personnel only and must
always match the serial number located on the chassis.
After reading the warning message, press any key to display the spaces in which to enter the serial
number value.
124
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Product ID
The Product ID option sets the system product ID, which is found on the product ID sticker on the
chassis.
IMPORTANT: The Product ID should be modified by qualified service personnel only and must
always match the Product ID located on the chassis.
After reading the warning message, press any key to display the spaces for entering the product
ID value.
Advanced Options menu
125
Advanced Performance Tuning Options
Depending on your server model, options may include:
126
•
“HW Prefetcher” (page 127)
•
“Adjacent Sector Prefetch” (page 128)
•
“DCU Prefetcher” (page 129)
•
“DCU Streamer Prefetcher” (page 130)
•
“DCU IP Prefetcher” (page 131)
•
“Data Reuse” (page 132)
•
“Hardware Prefetch training on Software Prefetch” (page 133)
•
“DRAM Prefetch on CPU Request” (page 134)
•
“DRAM Prefetch on I/O Request” (page 135)
•
“CPU Core Hardware Prefetcher” (page 136)
•
“CPU Cache Stride Prefetcher” (page 137)
•
“Stack Engine Prediction” (page 138)
•
“Node Interleaving” (page 139)
•
“1333 MHz Support for 3DPC-10600H HP SmartMemory” (page 140)
•
“Data Direct I/O” (page 141)
•
“Memory Channel Mode” (page 142)
•
“Memory Speed with 2 DIMMs per Channel” (page 143)
•
“Hemisphere Mode” (page 144)
•
“HPC Optimization Mode” (page 145)
•
“ACPI SLIT Preferences” (page 146)
•
“Intel Performance Counter Monitor (PCM)” (page 146)
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
HW Prefetcher
NOTE:
This option is available on servers with Intel processors.
This option controls processor prefetch features. In most cases, this option should remain enabled.
With certain workloads, however, disabling this option may provide a performance benefit. Disable
this option only after performing application benchmarking to verify improved performance in a
particular environment.
IMPORTANT:
performance.
Disabling this option is not recommended because it typically degrades system
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
127
Adjacent Sector Prefetch
NOTE:
This option is available on servers with Intel processors.
This option controls processor prefetch features. In most cases, this option should remain enabled.
With certain workloads, however, disabling this option may provide a performance benefit. Disable
this option only after performing application benchmarking to verify improved performance in a
particular environment.
IMPORTANT:
performance.
Disabling this option is not recommended because it typically degrades system
Options include:
128
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
DCU Prefetcher
NOTE:
This option is available on G7 and earlier servers with Intel processors.
This option controls processor prefetching. In most cases, this option should remain enabled. With
certain workloads, however, disabling this option may provide a performance benefit. Disable
this option only after performing application benchmarking to verify improved performance in a
particular environment.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
129
DCU Streamer Prefetcher
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls processor prefetching. In most cases, this option should remain enabled. With
certain workloads, however, disabling this option may provide a performance benefit. Disable
this option only after performing application benchmarking to verify improved performance in a
particular environment.
Options include:
•
Enabled (default)
•
Disabled
130 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
DCU IP Prefetcher
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls processor prefetching. In most cases, this option should remain enabled. With
certain workloads, however, disabling this option may provide a performance benefit. Disable
this option only after performing application benchmarking to verify improved performance in a
particular environment.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
131
Data Reuse
NOTE:
This option is available on G7 servers with Intel processors.
This option controls data flow between cache levels. In most cases, this option should remain
enabled. With certain workloads, however, disabling this option may provide a performance
benefit. Disable this option only after performing application benchmarking to verify improved
performance in a particular environment.
Options include:
132
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Hardware Prefetch training on Software Prefetch
NOTE:
This option is available on G7 servers with AMD processors.
The processor assists and calibrates with software prefetching (also known as predicting)
technologies for better use of system memory when using applications that manage or request the
same kind of information frequently. This option controls those processor prefetch features.
In most cases, this option should remain enabled. With certain workloads, however, disabling this
option may provide a performance benefit. Disable this option only after performing application
benchmarking to verify improved performance in a particular environment.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
133
DRAM Prefetch on CPU Request
NOTE:
This option is available on G7 and Gen8 servers with AMD processors.
Depending on the type of application or software being used, the processor constantly prefetches
data from RAM memory to decrease system latency. This option controls those processor prefetches.
In most cases, this option should remain enabled. With certain workloads, however, disabling this
option may provide a performance benefit. Disable this option only after performing application
benchmarking to verify improved performance in a particular environment.
Options include:
134
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
DRAM Prefetch on I/O Request
NOTE:
This option is available on G7 and Gen8 servers with AMD processors.
Depending on the type of I/O and expansion cards being used, the processor constantly prefetches
data from RAM to decrease latency within the I/O subsystems and expansion cards. This option
controls those processor prefetch features.
In most cases, this option should remain enabled. With certain workloads, however, disabling this
option may provide a performance benefit. Disable this option only after performing application
benchmarking to verify improved performance in a particular environment.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
135
CPU Core Hardware Prefetcher
NOTE:
This option is available on G7 and Gen8 servers with AMD processors.
This option controls prefetch capability activation between processor cores. In most cases, this
option should remain enabled. With certain workloads, however, disabling this option may provide
a performance benefit. Disable this option only after performing application benchmarking to verify
improved performance in a particular environment.
Options include:
136
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
CPU Cache Stride Prefetcher
NOTE:
This option is available on servers with AMD processors.
This option controls prefetch capability activation between processor cores. In most cases, this
option should remain enabled. With certain workloads, however, disabling this option may provide
a performance benefit. Disable this option only after performing application benchmarking to verify
improved performance in a particular environment.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
137
Stack Engine Prediction
NOTE:
This option is available on servers with AMD processors.
This option controls the processor Stack Engine Prediction logic.
CAUTION:
Disabling this option may degrade system performance.
After reading the warning message, press any key to display the following settings:
138
•
Enabled (default)
•
Disabled
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Node Interleaving
Node Interleaving disables the NUMA architecture properties of the system. All operating systems
supported by this platform support NUMA architectures. In most cases, you can obtain optimum
performance by disabling Node Interleaving. When this option is enabled, memory addresses are
interleaved across the memory installed for each processor and some workloads may experience
improved performance.
IMPORTANT: Enabling Node Interleaving may impact operating system performance. Enabling
Node Interleaving requires that all nodes have equal memory sizes. This option is not present on
DL980 G7.
After reading the warning message, press any key to display the following settings:
•
Enabled
•
Disabled (default)
Advanced Options menu
139
1333 MHz Support for 3DPC-10600H HP SmartMemory
NOTE:
This option is available on Gen8 servers with 3DPC-10600H HP SmartMemory.
This option enables memory speed of 1333Mhz for 3-DIMM per channel configurations and should
be enabled only when the system contains PC3-10600H HP Smart Memory exclusively.
Options include:
•
Enabled
•
Disabled (default)
140 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Data Direct I/O
NOTE:
This option is available on Gen8 servers with Intel processors.
This option controls the ability for the processor to accelerate I/O operations by reducing the
number of I/O related memory accesses. This option increases I/O performance while reducing
system power and I/O latency and is highly recommended for low-latency environments.
Options include:
•
Enabled (default)
•
Disabled
Advanced Options menu
141
Memory Channel Mode
NOTE:
This option is available on select servers.
Memory Channel Mode sets the memory to work in Lockstep or Non-Lockstep mode.
Options include:
•
Independent Channel Mode (Non-Lockstep) (default)—Uses the standard error correction
mechanism of Advanced ECC.
•
Combined Channel Mode (Lockstep)—Provides maximum data protection by allowing multiple-bit
memory errors to be corrected in certain instances not possible in Advanced ECC mode.
NOTE: Lockstep Mode (used for Intel servers) and Memory Channel Mode (used for AMD
servers) provide the same functionality, allowing the memory controller to correct up to 8 bad
bits that are byte aligned.
Activating Combined Channel Mode has some memory population rules. For more information,
see the user guide or QuickSpecs for the server.
142
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Memory Speed with 2 DIMMs per Channel
NOTE:
This option is available on G7 servers with Intel 5500-series processors.
This option configures the system to run DIMMs at 1333 MHz when up to two DIMMs are installed
on a memory channel, if all other requirements for 1333 MHz operation are met. This provides a
performance increase for most workloads. By default, the system will operate at a maximum 1066
MHz when two DIMMs are installed on any memory channel. HP has validated this functionality
with all HP DIMMs.
HP recommends that this setting remain at the default of 1066 MHz maximum when using DIMMs
not manufactured by HP.
Advanced Options menu
143
Hemisphere Mode
NOTE:
This option is available on HP ProLiant DL580 G7, BL620c G7 and BL680c G7 servers.
Hemisphere mode is equivalent to socket level memory interleaving.
Options include:
•
Auto (default)
•
Disabled
144 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
HPC Optimization Mode
NOTE:
This option is available on DL585 G7 and BL685c G7 servers with AMD processors.
This mode is specially designed for customers deploying servers in a High Performance Computing
environment. When this mode is enabled, the performance of the processor can be maintained at
a high level even if the processor temporarily exceeds the normal power threshold.
Options include:
•
Enabled
•
Disabled (default)
Advanced Options menu
145
ACPI SLIT Preferences
NOTE:
This option is available on select Intel and AMD G7 servers and on all Gen8 servers.
The ACPI SLIT (System Locality Information Table) describes the relative access times between
processors, memory subsystems, and I/O subsystems. Operating Systems that support the SLIT can
use this information to improve performance by allocating resources and workloads more efficiently.
Options include:
•
Enabled (default)
•
Disabled
Intel Performance Counter Monitor (PCM)
NOTE:
This feature is supported only on Gen8 servers.
When enabled, this option allows you to view and use certain performance counters in the
processor, such as the Performance Counter Monitor (PCM).
Options include:
146
•
Enabled
•
Disabled (default)
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Advanced Options menu
147
One Terabyte Memory Limit
NOTE:
This option is available on G7 and Gen8 servers with AMD processors.
This option controls the system addressable memory range.
Options include:
•
Limit memory to below 1TB (default)
•
Enable all memory
IMPORTANT: Some environments may experience problems when 1 TB or greater memory is
made available to the operating system.
148
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Drive Write Cache
NOTE: This option is available on G7 servers. For Gen8 servers, this option is in under System
Options > SATA Controller Options (“Drive Write Cache” (page 43))
The Drive Write Cache option controls the state of the write cache of the drives attached to the
supported controller. This feature provides greater drive performance but could result in data
corruption during an unexpected power loss or shutdown.
This option only affects operation for fixed drives attached to the embedded SATA controller when
not operating in a software RAID mode. This option has no effect if fixed drives are attached to
an embedded or optional Smart Array controller or if the Smart Array B110i Software RAID solution
is used.
CAUTION: Enabling Drive Write Cache may result in data loss or data corruption if an unexpected
power loss occurs.
After reading the warning message, press any key to display the following settings:
•
Enabled
•
Disabled (default)
Advanced Options menu
149
Asset Tag Protection
This option locks or unlocks the Asset Tag information. When the Asset Tag information is locked,
the Asset tag is not erased when the default system settings are restored.
After reading the warning message, press any key to display the following settings:
150
•
Locked
•
Unlocked (default)
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
SR-IOV
NOTE:
This option is available on select G7 servers and all Gen8 servers.
This option controls Single Root I/O Virtualization. SR-IOV is supported on select operating systems
and allows, in some cases, the creation of separate virtual instances of a PCIe device. In certain
environments, this may increase virtual machines and hypervisor response times.
Options include:
•
Enabled
•
Disabled (default)
Advanced Options menu
151
Embedded SATA RAID
NOTE:
This option is available on select G6 and G7 servers.
This option activates RAID functions on the SATA controller, if such functions are available.
Options include:
•
Enabled
•
Disabled (default)
CAUTION: Enabling Drive Write Cache may result in data loss or data corruption if an unexpected
power loss occurs.
152
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
System Default Options menu
•
“Restore Default System Settings” (page 153)
•
“Restore Settings/Erase Boot Disk” (page 154)
•
“User Default Options” (page 155)
Restore Default System Settings
This option resets all configuration settings to their default values and immediately and automatically
restarts the server.
CAUTION: This option resets all configuration settings to their default values. Any modifications
will be lost.
After reading the warning message, press any key to display the following confirmation responses:
•
No, Abort Restore (default)
•
Yes, Select to Restore
System Default Options menu
153
Restore Settings/Erase Boot Disk
The Restore Settings/Erase Boot Disk option resets the date, time, and all configuration settings to
default values. Data on the boot disk drive is erased, and changes that have been made are lost.
CAUTION: Restoring Default Settings and Erasing Boot Disk resets all configuration settings to
their default values and deletes all fixed disk partitions. Any modifications, including all fixed disk
partitions, will be lost.
After reading the warning message, press any key to display the following confirmation responses:
•
No, Abort Restore/Erase (default)
•
Yes, Select to Restore/Erase
154 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
User Default Options
This feature enables the user to define custom default configuration settings. When the default
configuration settings are loaded, the user-defined default settings are used instead of the factory
defaults. To save the configuration as the default configuration, configure the system and then
enable this feature.
Confirmation responses include:
•
Save User Defaults (default)
•
Erase User Defaults
System Default Options menu
155
Utility Language menu (G5 through G7 servers)
The Utility Language menu enables you to set the display language for RBSU.
Options include:
156
•
English (default)
•
Spanish
•
German
•
French
•
Italian
•
Japanese
RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
Utility Language menu (Gen8 servers)
The Utility Language menu enables you to set the display language for RBSU.
Options include:
•
English (default)
•
Japanese
Utility Language menu (Gen8 servers)
157
3 RBSU menu-driven interface, version 2.xx (G5 and earlier
servers)
RBSU main menu
NOTE:
Menu options may differ from those in this document, depending on the server model.
On the left-hand side of the screen, the RBSU menu lists configuration settings to view or modify.
On the right-hand side of the screen, a window displays basic server information, including the
server model, serial number, BIOS version, backup BIOS version, memory installed, and processors
installed.
NOTE:
To see online help, highlight the selection and press F1. All menus are in English only.
Each RBSU sub-menu and its options are described in this chapter.
System Options menu
The System Options menu enables basic I/O server configuration with the following options:
158
•
“Embedded Serial Port A” (page 159)
•
“Embedded Serial Port B” (page 160)
•
“Virtual Serial Port” (page 161)
•
“Optional LPT Mode Support” (page 161)
•
“Optional LPT Mode Support” (page 161)
•
“Integrated Diskette Controller” (page 161)
•
“NUMLOCK Power-On State” (page 161)
•
“Embedded NICs” (page 162)
•
“Diskette Write Control” (page 162)
•
“Diskette Boot Control” (page 162)
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
•
“Advanced Memory Protection” (page 163)
•
“USB Control” (page 164)
•
“USB 2.0 EHCI Controller” (page 164)
•
“Power Regulator for ProLiant” (page 165)
•
“USB External Port Capability” (page 166)
•
“Ultra Low Power State” (page 167)
NOTE: Menu options may differ from those in this document, depending on specific server
options.
Embedded Serial Port A
The Embedded Serial Port A option sets the configuration for the internal serial port A. The settings
include the address and IRQ. This option can also disable the port.
NOTE: Embedded Serial Port options may be named Embedded COM Port options, depending
on the server.
System Options menu
159
Embedded Serial Port B
The Embedded Serial Port B option sets the configuration for the internal serial port B. The settings
include the address and IRQ. This option can also disable the port.
NOTE: Embedded Serial Port options may be named Embedded COM Port options, depending
on the server.
160 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Virtual Serial Port
The Virtual Serial Port option assigns the logical COM Port number and associated default resources
used by the Virtual Serial Port. When enabled, the option provides remote access through the iLO
management controller to BIOS Serial Console.
For more information about iLO configurations, see the iLO user documents on the Documentation
CD or HP website (http://www.hp.com/go/ilo/docs).
Optional LPT Mode Support
The Optional LPT Mode Support option assigns the local port number and associated default
resources to the selected physical LPT. The menu includes the following options:
•
SPP Extended
•
EPP 1.9
•
ECP w/EPP
The OS might overwrite the setting.
Integrated Diskette Controller
The Integrated Diskette Controller option is a simple toggle setting that enables or disables the
diskette drive. When this option is disabled, the server cannot read from or write to the drive.
Therefore, Diskette Write Control and Diskette Boot Control are irrelevant when Integrated Diskette
Controller is disabled.
NUMLOCK Power-On State
The NUMLOCK Power-On State option is a simple toggle setting that enables or disables the
power-up state of the NUMLOCK key. When the NUMLOCK key is enabled, the machine powers
up with the NUMLOCK key active.
System Options menu
161
Embedded NICs
The Embedded NICs option enables iSCSI or PXE Boot support. This option enables the server to
boot to the network (embedded NIC only) and attach to a PXE server with boot images. The option
also enables the NIC port to display in the Standard Boot Order (IPL) list. For NIC 1, the default
setting is PXE Boot, but for subsequent NICs, the default setting is Disabled. For more information
on PXE technology, see the Using PXE Technology on Compaq ProLiant Servers white paper on
the HP website (http://h50146.www5.hp.com/products/software/oe/linux/mainstream/bin/
support/doc/pdf/pxe_13sd-1100a-wwen_rev1_us.pdf).
When enabling PXE or iSCSI Boot support, the NIC does not display in the Standard Boot Order
(IPL) until the next reboot.
Diskette Write Control
The Diskette Write Control option is a simple toggle setting that sets the write controls for the diskette
drive. The available configuration settings are either Read and Write or Read Only. When Read
and Write is selected, the server can both read data from and write data to the diskette drive.
Diskette Boot Control
The Diskette Boot Control option is a simple toggle setting that enables the diskette drive to be used
as a boot device. When this option is disabled, the server cannot boot from the diskette drive. This
configuration setting is used as a security feature.
162
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Advanced Memory Protection
The Advanced Memory Protection option provides additional memory protection beyond ECC.
For more information about Advanced Memory Protection, see HP ProLiant Advanced Technology
on the HP website (http://h18004.www1.hp.com/products/servers/technology/
memoryprotection.html).
•
The Advanced ECC Support (maximum memory) setting disables additional resiliency and
provides the largest memory capacity to the OS.
•
The Online Spare with Advanced ECC Support setting requires a single group of spare modules
and provides automatic failover of degraded modules in the system while it is running.
•
The Mirrored Memory with Advanced ECC Support option provides protection against
uncorrectable memory errors that would otherwise result in system failure. DIMM banks A and
B are mirrored by DIMM banks C and D on the same memory board. The failed memory can
be replaced while the system is running.
Mirrored DIMM pairs must be the same size to allow selection of single-board mirrored memory
or dual-board mirrored memory. Pairing different size DIMMs results in the following caution:
Current memory configuration does not support Online Spare.
System Options menu
163
USB Control
The USB Control menu determines how USB ports and embedded devices operate at startup:
•
When USB Enabled is selected, all USB ports and embedded devices are enabled.
•
When USB Disabled is selected, all USB ports and embedded devices are disabled.
•
When Legacy USB Disabled is selected, all USB ports are enabled under a USB-aware OS,
but USB is not supported during POST or RBSU. Legacy USB Disabled also disables iLO virtual
devices.
•
When External USB Port Disabled is selected, external USB ports are disabled. Under this
option, embedded USB devices still have full support under the ROM and OS.
USB 2.0 EHCI Controller
The USB 2.0 EHCI Controller option is a toggle setting that enables or disables the high-speed
USB 2.0 controller.
164 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Power Regulator for ProLiant
The Power Regulator for ProLiant option provides multiple options for managing power usage of
servers:
•
In the HP Dynamic Power Savings Mode, the system adjusts the power and performance of
the processor to the workload of the processor.
•
In the HP Static Low Power Mode, the system operates in a lower state of performance.
•
In the HP Static High Performance Mode, the system operates in its maximum performance
state.
•
In the OS Control Mode, processors operate at maximum speed unless the OS enables a
power management policy.
System Options menu
165
USB External Port Capability
The USB External Port Capability option configures the USB external ports to operate at USB 1.1
or USB 2.0 speeds.
Select USB 2.0 for improved performance if using an operating system other than Microsoft
Windows Server 2003 or Microsoft Windows Server 2003 x64.
NOTE: Running external USB ports at USB 2.0 with Microsoft Windows Server 2003 or Microsoft
Windows Server 2003 x64 causes delays during installations.
This selection does not affect the internal USB port or USB iLO Virtual Media devices.
166 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Ultra Low Power State
Ultra Low Power State enables the system to transition to the lowest processor power state when
the Power Regulator Mode is configured for HP Static Low Power Mode or HP Dynamic Power
Savings Mode. In HP Static Low Power Mode, power savings increases with a small impact on
maximum system performance. HP Dynamic Power Savings Mode increases power savings when
processor utilization is low.
Ultra Low Power State is supported only on HP ProLiant servers with AMD processors.
System Options menu
167
PCI Devices menu
The PCI Devices menu displays the configuration settings of the PCI devices installed in the server
and allows you to modify the IRQ. Multiple PCI devices can share an interrupt.
To disable a device, select the device and press the Enter key. A menu is displayed with options
to change the IRQ and disable the device.
NOTE: Only IRQs that are modified in RBSU retain the change during the next reboot. IRQs on
PCI devices that have not been modified are subject to change during reboot.
168 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Standard Boot Order (IPL) menu
The Standard Boot Order (IPL) option configures the Initial IPL device and controls the search order
the server uses to look for a bootable device.
NOTE: If you enable or disable a device, restart the server. Changes do not take effect until after
reboot.
Standard Boot Order (IPL) menu
169
Boot Controller Order menu
The Boot Controller Order option selects which of the installed mass storage devices is used as the
primary boot controller. The server attempts to power up with the OS on this device.
The primary boot controller is set to controller 1.
NOTE:
Changes made to the Boot Controller Order in the ORCA Utility are reflected in this menu.
IMPORTANT: PCI devices that have been disabled in the PCI Devices menu might still be visible
on the Boot Controller Order screen.
Date and Time menu
The Date and Time option sets the system time and date. Enter the date in a month-day-year
(mm-dd-yyyy) format. Enter the time in an hour-minute-second (hh:mm:ss) format.
Server Availability menu
The Server Availability menu includes options that configure the ASR features:
170
•
“ASR Status” (page 171)
•
“ASR Timeout” (page 171)
•
“Thermal Shutdown” (page 171)
•
“Wake-On LAN” (page 171)
•
“POST Speed Up” (page 171)
•
“POST F1 Prompt” (page 172)
•
“Power Button” (page 172)
•
“Automatic Power-On” (page 172)
•
“Power-On Delay” (page 172)
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
ASR Status
The ASR Status option is a toggle setting that either enables or disables ASR. When set to Disabled,
no ASR features function.
ASR Timeout
The ASR Timeout option sets a timeout limit for resetting a server that is not responding. When the
server has not responded in the selected amount of time, the server automatically resets. The
available time increments are:
•
10 minutes
•
15 minutes
•
20 minutes
•
30 minutes
•
5 minutes
Thermal Shutdown
The Thermal Shutdown option is a toggle setting that determines when the server automatically
powers down due to dangerous temperatures. When the setting is enabled (default), the Advanced
System Management Driver initiates a system shutdown when the temperature reaches within 5
degrees of critical level. When the setting is disabled, the Advanced System Management Driver
shuts down the system at critical level.
Wake-On LAN
The Wake-On LAN option is a toggle setting that enables or disables the Wake-On LAN feature.
When set to Enabled, the server can be powered up remotely using a network controller. When
changing to Enabled, the following caution appears:
When enabling Wake-on LAN, remove all power cords before adding or
removing any adapters. Some adapters can cause the system to power on
when added or removed.
POST Speed Up
The POST Speed Up option is a toggle setting that enables or disables the extended power-up
memory test. When POST Speed Up is set to Enabled, the extended power-up memory test is not
executed, and the server powers up more quickly.
Server Availability menu
171
POST F1 Prompt
The POST F1 Prompt option is a toggle setting that configures the server so the F1 key must be
pressed to proceed when an error is encountered during the power-up sequence. A series of system
tests executes during POST before continuing with the following:
•
If failures occur that allow the system to continue operating, the system continues to boot but
posts a message.
•
If critical components fail or are missing, the server attempts to boot. If it can boot, it posts a
message and an F1 prompt.
•
◦
If Enabled is selected and an error occurs, the system stops at the F1 prompt until the F1
key is pressed, before continuing to boot.
◦
If Delayed is selected and an error occurs, the system pauses for 20 seconds at the F1
prompt, and then continues to boot the OS.
If the system cannot run with the missing or failed components, it halts until those components
are replaced.
NOTE: The POST F1 Prompt setting is enabled by default in ProLiant ML and DL servers and
is disabled by default in BL servers.
Power Button
Disabling the Power Button feature causes the momentary power button to stop functioning under
any OS. The Power Button feature does not override the 4-second hold-down of the server power
button.
Automatic Power-On
The Automatic Power-On feature enables the server to automatically power on when auxiliary
power is applied to the server.
Power-On Delay
The Power-On Delay feature delays the server from powering on for a specified time to prevent
power usage spikes when multiple servers power up after a power loss. Wake-on LAN, RTC
wake-up, and iLO Virtual Power Button events override the delay and immediately power on the
server.
The Power-On Delay options are:
•
Disabled
•
15-second delay
•
30-second delay
•
45-second delay
•
60-second delay
•
Random delay
Server Passwords menu
The Server Passwords menu includes options that configure the password environment of the server:
172
•
“Set Power-On Password” (page 173)
•
“Set Admin Password” (page 173)
•
“Trusted Platform Module” (page 173)
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
•
“Network Server Mode” (page 175)
•
“QuickLock” (page 175)
Set Power-On Password
The Set Power-On Password option sets a password that controls access to the server during
power-up. The server cannot be powered up until the correct password is entered. . To disable or
clear the password, enter the password followed by a / (slash) when prompted to enter the
password.
Password requirements:
•
Seven characters maximum.
•
Can be any combination of numbers, letters, and special characters.
NOTE: If more than seven characters are entered and accepted as the password, it will not be
recognized when next powering on the server. However, if just the first seven characters of that
password are entered, it will be recognized, allowing POST to continue.
Set Admin Password
The Set Admin Password option sets a password to control access to the RBSU and the System
Maintenance Menu. If set, this password must be entered when F9 or F10 is pressed during POST.
To disable or clear the password, enter the password followed by a / (slash) when prompted to
enter the password.
Password requirements:
•
Seven characters maximum.
•
Can be any combination of numbers, letters, and special characters.
NOTE: If more than seven characters are entered and accepted as the password, it will not be
recognized when next logging in to the RBSU. However, if just the first seven characters of that
password are entered, it will be recognized, allowing access to the RBSU.
Trusted Platform Module
The Trusted Platform Module menu includes options that configure the optional Trusted Platform
Module installed on HP ProLiant Generation 5p Servers:
•
“TPM Functionality” (page 174)
•
“TPM Visibility” (page 174)
•
“TPM Expansion ROM Measuring” (page 174)
•
“TPM Clear” (page 175)
Server Passwords menu
173
TPM Functionality
Enabling TPM Functionality enables the TPM and BIOS secure startup. The TPM is fully functional
in this mode.
CAUTION: When a TPM is installed and enabled on the server, data access is locked if you fail
to follow the proper procedures for updating the system or option firmware, replacing the system
board, replacing a hard drive, or modifying OS application TPM settings.
For information on installing and enabling the TPM module option, see the HP Trusted Platform
Module Option Installation Instructions that ships with the option.
Disabling TPM Functionality disables the BIOS secure startup but still allows the TPM to be visible
to the operating system. The TPM can respond to most commands in this mode.
Selecting Disabled may prevent the server from booting to a TPM-aware operating system.
TPM Visibility
The TPM Visibility option provides the ability to hide the TPM from the operating system. When
the TPM is hidden, BIOS secure startup is disabled, and the TPM does not respond to any commands
from any software.
Hiding the TPM may prevent the server from booting to a TPM-aware operating system.
TPM Expansion ROM Measuring
TPM Expansion ROM Measuring enables the BIOS to measure the optional PCI or PCIe expansion
ROM code and store that measurement in the TPM. On subsequent reboots, operating systems or
validation software that utilize the measurements stored in the TPM can use this data to detect
modifications to PCI or PCIe expansion ROM versions.
174
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
TPM Clear
The TPM Clear option allows the user to reset the TPM to factory settings, clearing any assigned
passwords, keys, or ownership.
Clearing the TPM may prevent the server from booting to a TPM-aware operating system.
Network Server Mode
The Network Server Mode option is a toggle setting that sets the server to operate in network server
mode. This feature works in conjunction with the power-on password. When set to Disabled, the
server operates normally. When it is set to Enabled, the following actions occur:
•
The local keyboard remains locked until the power-on password is entered.
•
The power-on password prompt is bypassed.
•
When a diskette is in the diskette drive, the server does not start unless the power-on password
is entered locally.
IMPORTANT: Network server mode cannot be enabled until the power-on password has
been established.
NOTE:
Generation 8 Servers do not support Network Server Mode.
QuickLock
The QuickLock option is a toggle setting that either enables or disables the QuickLock feature.
When set to Enabled, the keyboard is locked by pressing the Ctrl+Alt+L keys. The keyboard remains
locked until the power-on password is typed.
NOTE: If the power-on password is disabled at the power-on key prompt, the QuickLock feature
remains inactive until the password is changed in RBSU.
BIOS Serial Console and EMS menu
IMPORTANT:
Some languages or characters may require a specific emulation mode.
The BIOS Serial Console and EMS feature configures the serial port to view POST error messages
and run RBSU remotely through a serial connection to the server COM port. The remote server
does not require a keyboard or mouse. BIOS Serial Console is disabled in the ROM by default.
EMS is enabled in the OS by default, but must also be enabled in the ROM.
For more information about the BIOS Serial Console, see “RBSU BIOS Serial Console (CLI)”
(page 189).
BIOS Serial Console design supports VT100+ protocol, and ANSI and V100 terminal emulation.
VT100 is supported by all terminal emulation programs. However, ANSI supports enhanced
graphics and is more aesthetically appealing to some users. ANSI is the recommended choice if
it meets the system requirements. CLI support is available on some new servers for faster, more
compatible display when configuring a server using VT100 emulation. For more information, see
“BIOS Serial Console/CLI overview” (page 189).
When viewed in BIOS Serial Console, the RBSU main menu looks slightly different from the local
server view.
The following menu options are available:
•
“BIOS Serial Console Port” (page 176)
•
“BIOS Serial Console Baud Rate” (page 176)
BIOS Serial Console and EMS menu
175
•
“EMS Console” (page 178)
•
“BIOS Interface Mode” (page 179)
BIOS Serial Console Port
The BIOS Serial Console Port option provides additional selections for enabling BIOS Serial
Console.
NOTE: A null modem cable should be connected to the serial port/COM port which BIOS Serial
Console is enabled.
NOTE: On select newer servers, the BIOS Serial Console Port default is Auto instead of Disabled.
During the boot process, the server checks for the presence of a VT100 compatible client running
at 9600 Baud connected to the server and automatically enables the BIOS Serial Console for that
boot if one is found. This eliminates the need to run RBSU with a local keyboard and monitor
attached to enable the BIOS Serial Console feature.
BIOS Serial Console Baud Rate
The BIOS Serial Console Baud Rate option enables baud rate changes.
176
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
BIOS Serial Console and EMS menu 177
EMS Console
The EMS Console option is a Microsoft Windows Server 2003 feature that enables the Emergency
Management Console to be redirected through the serial port. The EMS Console feature is disabled
by default.
•
When using iLO, select the value (COM 1 or COM 2) assigned to the Virtual Serial Port
(“Virtual Serial Port” (page 161)).
•
When redirecting EMS through a physical serial port, select the value assigned to the Embedded
Serial Port (“Embedded Serial Port A” (page 159)).
The EMS Console option is a Microsoft Windows Server 2003 feature that enables the Emergency
Management Console to be redirected through the serial port. When using iLO, select the value
(COM 1 or COM 2) assigned to the Virtual Serial Port). When redirecting EMS through a physical
serial port, select the value assigned to the Embedded Serial Port. The EMS Console feature is
disabled by default.
EMS provides input/output support for all Microsoft Windows kernel components: the loader,
setup, recovery console, OS kernel, blue screens, and the Special Administration Console. The
Special Administration Console is a text mode management console available after Windows
Server 2003 OS has initialized. For more information on EMS, go to the Microsoft website
(www.microsoft.com).
Microsoft enables EMS in the OS, but EMS must also be enabled in the ROM. EMS, when enabled,
assumes the serial port for redirection and may cause interference with other devices attached to
the serial port. To avoid interference, EMS is disabled in the system ROM by default on ML and
DL servers. If EMS is disabled in Windows Server 2003, perform the following steps to update the
boot.ini file:
1. Enable EMS in RBSU.
2. Run bootcfg/ems on/id 1.
3. Reboot.
178
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
BIOS Interface Mode
When Auto is selected as the BIOS Interface Mode, CLI mode is automatically selected for this
POST only if the keyboard buffer receives characters from the serial port instead of the keyboard.
When Command-Line is selected, CLI mode is automatically enabled.
Server Asset Text menu
The Server Asset Text menu includes options that customize the system-specific text for the server.
The following menu options are available:
•
“Set Server Info Text” (page 179)
•
“Set Administrator Info Text” (page 179)
•
“Set Service Contact Text” (page 180)
•
“Custom POST Message” (page 181)
Set Server Info Text
The Set Server Info Text option defines reference information for the server. The setting is blank by
default.
•
Server Name defines a two-line name identifying the server. A maximum of 14 characters
can be entered on each line.
•
Server Asset Tag defines a two-line asset tag to identify the server. A maximum of 16 characters
can be entered on each line.
•
Server Primary OS defines a three-line description of the primary OS of the server. A maximum
of 14 characters can be entered on each line.
•
Other Text defines two lines of additional text describing the server. A maximum of 14
characters can be entered on each line.
Set Administrator Info Text
The Set Administrator Info Text option defines reference information for the server administrator.
Server Asset Text menu
179
•
Admin Name Text defines a two-line description for the server administrator name. A maximum
of 14 characters can be entered on each line.
•
Admin Phone Number Text defines two lines of text for the server administrator phone number.
A maximum of 14 characters can be entered on each line.
•
Admin Pager Number Text defines two lines of text for the server administrator pager number.
A maximum of 14 characters can be entered on each line.
•
Other Text defines two lines of additional text relating to the server administrator. A maximum
of 14 characters can be entered on each line.
Set Service Contact Text
The Set Service Contact Text option defines reference information for the service contact of the
server.
180 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
•
Service Name Text defines a two-line description for the service contact name. A maximum
of 14 characters can be entered on each line.
•
Service Phone Number Text defines two lines of text for the service contact phone number. A
maximum of 14 characters can be entered on each line.
•
Service Pager Number Text defines two lines of text for the service contact pager number. A
maximum of 14 characters can be entered on each line.
•
Other Text defines two lines of additional text relating to the service contact. A maximum of
14 characters can be entered on each line.
Custom POST Message
The Custom POST Message option enables entry of a custom message to display during POST.
Advanced Options menu
The Advanced Options menu includes options that enable you to configure the advanced features
of the server:
•
“Multi-Processor Specification (MPS) Table Mode” (page 182)
•
“ROM Selection” (page 182)
•
“Restore Default System Settings” (page 183)
•
“Restore Settings/Erase Boot Disk” (page 183)
•
“User Default Options” (page 183)
•
“NMI Debug Button” (page 184)
•
“Virtual Install Disk” (page 184)
•
“Secondary IDE Channel Support” (page 184)
•
“BIOS Enhanced RAID” (page 184)
•
“Node Interleaving” (page 184)
•
“Serial Number” (page 185)
•
“Product ID” (page 185)
Advanced Options menu
181
•
“Drive Write Cache” (page 185)
•
“SATA Software RAID” (page 185)
•
“Optional PCI-X Riser Fan Monitoring” (page 185)
•
“Processor Options” (page 185)
•
“Power Supply Requirements Override” (page 186)
•
“Embedded VGA Control” (page 187)
NOTE: Menu options may differ from those in this document, depending on specific server
options.
Multi-Processor Specification (MPS) Table Mode
The MPS Table Mode option is automatically set, based on the OS selected, and is used for interrupt
routing.
IMPORTANT: This setting is pre-selected. You can override the default setting at this menu, but
successful OS operation is dependent upon the correct (default) setting.
ROM Selection
The ROM Selection option toggles the server ROM between the current ROM and the backup
ROM. All servers with redundant ROMs enable you to switch to the backup ROM.
182
RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Restore Default System Settings
The Restore Default System Settings option resets the non-volatile memory of the server to an initial,
factory state when Yes, Select to Erase is selected. Selecting the Restore Default System Settings
option results in the following message:
Caution: Clearing NVRAM will reset all configuration settings to their
default values. Changes that have been made will be lost.
Restore Settings/Erase Boot Disk
The Restore Settings/Erase Boot Disk option resets the date, time, and all configuration settings to
default values. Data on the boot disk drive is erased, and changes that have been made are lost.
User Default Options
User Default Options enable definition of default configuration settings. When the system is
configured with default settings and saved, the new default settings override factory defaults.
Advanced Options menu 183
NMI Debug Button
The NMI Debug Button option is a simple toggle setting that enables you to enable debug
functionality when the system has experienced a software lock-up. The NMI Debug Button generates
an NMI to allow the use of the OS debugger.
NOTE: When enabled, pressing the NMI Debug Button on the system board during normal OS
operation generates a Blue-Screen Trap, ABEND, or Panic, and halts the system.
Virtual Install Disk
The virtual install disk is a holding place within the system ROM that contains embedded boot
drivers (such as SCSI or RAID controller drivers) that may be necessary to complete the operating
system installation. Typically, boot drivers that are placed in the virtual install disk are either not
included as part of the operating system media or are updated for new controllers. Supported
operating systems automatically find these drivers, eliminating the need for user intervention. To
further optimize the system, HP recommends updating these boot drivers to the latest version after
the OS install.
Secondary IDE Channel Support
The Secondary IDE Channel Support option is a toggle setting that enables or disables the secondary
IDE channel. When enabled, an additional IDE device can be connected to the secondary IDE
channel.
BIOS Enhanced RAID
The BIOS Enhanced RAID feature is a toggle setting that, when enabled, analyzes the Linux data
on installed hard drives for failure information. Based on the analysis, the system ROM automatically
chooses which hard drive to boot.
Node Interleaving
The Node Interleaving feature requires all nodes to have equal memory sizes when enabled.
Enabling Node Interleaving may affect OS performance.
184 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Serial Number
The Serial Number option Enables you to change the serial number. HP recommends that you do
not change this number, unless you are replacing a system board. When the Serial Number option
is chosen, a warning appears:
The serial number should ONLY be modified by qualified service personnel.
This value should always match the serial number located on the chassis.
Product ID
The Product ID option sets the system product ID, which is found on the product ID sticker on the
chassis. When the Product ID option is chosen, a warning appears:
The Product ID should ONLY be modified by qualified service personnel.
This value should always match the Product ID located on the chassis.
Drive Write Cache
The Drive Write Cache option controls the state of the write cache of the drives attached to the
supported controller. When the Drive Write Cache option is chosen, a warning appears:
Enabling Drive Write Cache may result in data loss or data corruption
if an unexpected power loss occurs.
SATA Software RAID
The SATA Software RAID feature enables RAID functionality (RAID 0 or RAID 1) for the embedded
SATA controller in the system. When the SATA Software RAID option is chosen, a warning appears:
Enabling Software RAID will result in data loss or data corruption on
existing SATA drives. Please backup all drives before enabling this
feature.
Optional PCI-X Riser Fan Monitoring
The Optional PCI-X Riser Fan Monitoring option, disabled by default, enables fan monitoring when
an optional PCI-X expansion cage is installed.
Processor Options
The Processor Options menu includes submenu options for processor settings:
•
“Processor Hyper-Threading” (page 185)
•
“HW Prefetcher” (page 186)
•
“Adjacent Sector Prefetch” (page 186)
•
“No-Execute Memory Protection” (page 186)
•
“Intel Virtualization Technology” (page 186)
•
“Expansion Card Caching Optimization” (page 186)
Processor Hyper-Threading
The Processor Hyper-Threading option is a toggle setting that allows Intel Hyper-Threading
Technology to be enabled or disabled, though it is enabled by default. Processor Hyper-Threading
delivers two logical processors that can execute multiple tasks simultaneously using shared hardware
resources of a single processor. The option is supported through the system BIOS. For more
information on processor Hyper-Threading, see the user documents for your server or processor.
Advanced Options menu 185
HW Prefetcher
The HW Prefetcher option allows processor prefetch features to be disabled. In most cases, the
option should remain enabled. The option should be disabled only after performing application
benchmarking to verify improved performance in a particular environment.
Adjacent Sector Prefetch
The Adjacent Sector Prefetch option allows processor prefetch features to be disabled. In most
cases, the option should remain enabled. The option should be disabled only after performing
application benchmarking to verify improved performance in a particular environment.
No-Execute Memory Protection
The No-Execute Memory Protection option, which is a toggle setting that is disabled by default,
provides protection against malicious codes and viruses. Unless the location specifically contains
executable code, memory is marked as non-executable.
Intel Virtualization Technology
The Intel Virtualization Technology option, when enabled, causes a Virtual Machine Manager to
utilize hardware capabilities provided by Intel Virtualization technology. The option is disabled
by default.
Expansion Card Caching Optimization
The Expansion Card Caching Optimization option allows some expansion cards to cache their
I/O resources for improved performance. If the expansion card and its driver do not support this
optimization, this option should remain disabled. When the option is enabled, a warning appears:
Setting this option to enabled may cause some system RAM to be
non-cacheable in certain uncommon memory configurations. See Help.
Power Supply Requirements Override
The Power Supply Requirements Override setting enables the system to boot and operate when
installed power supplies do not meet system requirements.
CAUTION: When Power Supply Requirements Override is enabled, some configurations may
not operate properly. Before enabling this option, verify and understand the system power
requirements.
186 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
Embedded VGA Control
NOTE:
The operating system video driver must support dual monitors.
NOTE:
The Embedded VGA Control option does not work with all video adapters.
The Embedded VGA Control option, set to Auto Detect by default, disables the embedded video
controller when an optional video controller is installed on the server.
When Always Enabled is selected, the system ROM enables the embedded video controller as the
primary video controller. This option provides dual-head support from both the embedded and
optional video controllers.
For more information on feature support and how to enable functionality, see the operating system
and video driver documentation.
Advanced Options menu
187
Utility Language menu
The Utility Language menu enables you to set the display language for RBSU.
188 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
4 RBSU BIOS Serial Console (CLI)
BIOS Serial Console/CLI overview
A menu-driven user interface and a CLI are required to support both a Windows/PC background
and a terminal/VT100 background. (The menu-driven interface does not display correctly on a
VT100 interface because menus that get paged in and out require the entire screen to be redrawn.)
By default, if BIOS Serial Console is disabled or not in use, the menu-driven interface is used.
On select newer servers, the BIOS automatically determines whether to run embedded ROM utilities
in menu-driven mode or CLI mode. If a VT100-compatible terminal is being used with BIOS Serial
Console, CLI mode is selected by default.
BIOS Serial Console setup
To use the BIOS Serial Console, several parameters must be set, including the COM port to use,
the baud rate, and default interface mode. Because menu options vary for different server models,
for more information, see one of the following sections:
•
Gen8 and G7 environments: “BIOS Serial Console & EMS menu” (page 95)
•
G6 and earlier environments: “BIOS Serial Console and EMS menu” (page 175)
In addition, a null modem cable should be connected to the serial port/COM port one which BIOS
Serial Console is enabled.
Terminal emulation options
BIOS Serial Console supports ANSI and VT100 terminal emulation and is designed to support
most terminal emulation programs. No special version of a terminal emulation program is required,
although the emulation modes supported may vary by vendors. To avoid compatibility problems,
only the core set of VT100 and ANSI terminal emulation is used in BIOS Serial Console. Although
this limits some capabilities, this protocol guarantees the maximum compatibility across different
platforms and vendors.
NOTE:
On some newer servers, emulation will be limited to VT100 compatibility.
Default settings for terminal emulation and baud rate can be changed through the ProLiant BL
e-Class Integrated Administrator for the current session only.
Microsoft HyperTerminal setup
Because Microsoft HyperTerminal is a widely used terminal emulation program, examples of
HyperTerminal 6.3 setup screens follow to aid in the initialization process. Be sure that the remote
terminal screen settings match the screens in this section. If using an emulation program other than
HyperTerminal, see the software reference material for settings information.
NOTE: Microsoft HyperTerminal settings must match BIOS Serial Console settings. Access the
OS terminal settings or RBSU to change the default settings.
1.
To access the font screen, select the View menu from the HyperTerminal main screen, and
then click Font. Select Terminal.
BIOS Serial Console/CLI overview 189
2.
3.
Access connection settings from the HyperTerminal main screen by selecting the File menu,
and then clicking Properties.
On the Connect To tab, click Configure to display the Port Settings tab.
NOTE: If using a notebook computer, the Connect using field should be set to COM1 or
COM2, depending on your configuration. COM1 is the HP default setting.
4.
Select Port Settings. Then click OK to return to the Properties screen.
190 RBSU BIOS Serial Console (CLI)
5.
6.
On the Properties screen, click the Settings tab.
If using ANSI emulation, click Terminal Setup and select ANSI (if using VT100 emulation, see
step 9). ANSI is the default setting.
NOTE:
7.
Both the remote and local machines must be set to the same emulation.
Select Terminal Settings.
Terminal emulation options
191
8.
9.
Click OK to return to the Settings tab, and click OK again to complete the HyperTerminal setup
process.
If using VT100 emulation, click Terminal Setup and select VT100.
NOTE: If using VT100 emulation, the setting must be changed from the default ANSI setting
in RBSU.
10. Select Terminal Settings. Click OK to return to the Settings tab.
192 RBSU BIOS Serial Console (CLI)
11. On the Settings tab, click ASCII Setup.
12. Deselect Wrap lines that exceed terminal width. Click OK to return to the Settings tab. Then
click OK to complete the HyperTerminal setup process.
Keystroke emulation
Because not all terminal emulation programs support function keys or special characters, certain
keystroke sequences are required for some commands.
Keystroke emulation
193
Escape sequences
BIOS Serial Console enables you to manually input unsupported keystrokes by entering escape
sequences. Each character must be entered within 2 seconds of pressing and holding down the
Esc key to emulate the escape sequence.
NOTE: You must use escape sequences if the emulation program does not support function keys,
but they also work if the emulation program does support function keys. To determine whether you
can use function keys, see the terminal emulation guide.
Function keys
Keyboard entry
Defined as
<ESC>1
F1
<ESC>2
F2
<ESC>3
F3
<ESC>4
F4
<ESC>5
F5
<ESC>6
F6
<ESC>7
F7
<ESC>8
F8
<ESC>9
F9
<ESC>0
F10
<ESC>!
F11
<ESC>@
F12
Control keys
Keyboard entry
Defined as
<ESC>h
Home
<ESC>k
End
<ESC>+
Insert
<ESC>-
Delete
<ESC>?
Page Up
<ESC>/
Page Down
Reset key
Keyboard entry
Defined as
<ESC>R<ESC>r<ESC>R
System Reset
Character translations in VT100 mode
The VT100 protocol does not support special characters such as line draw characters. These
characters are translated so that they can be displayed on the VT100 screen. Character translation
is used for improved VT100 screen display and has no effect on functionality of BIOS Serial
Console.
194
RBSU BIOS Serial Console (CLI)
Currently, the special characters in the table are translated into VT100 characters using VT100
protocol.
Special character
Translated into
Line draw character upper left corner
+
Line draw character lower left corner
+
Line draw character upper right corner
+
Line draw character lower right corner
+
Line draw character horizontal line
-
Line draw character vertical line
|
Inspect CLI Commands
Command
Usage
Description
HELP
HELP or HELP <command>
Displays all supported commands or
usage and descriptions of a specific
command.
EXIT
EXIT
Exits Inspect Utility and reboots.
QUIT
QUIT
Exits Inspect Utility and reboots.
EXPORT
EXPORT
Exports ALL information to a text file on
floppy drive A.
SHOW CONFIG
SHOW CONFIG
Displays all RBSU options and current
settings.
SHOW CMOS
SHOW CMOS
Displays all ISA CMOS.
SHOW IML
SHOW IML
Displays all system event log records.
SHOW SMBIOS
SHOW SMBIOS
Displays all SMBIOS record
information.
SHOW PCI
SHOW PCI
Displays all PCI devices and PCI header
information.
SHOW EVS
SHOW EVS
Displays all System EVs.
SHOW MEM
SHOW MEM
Displays system memory map.
SHOW SYS
SHOW SYS
Displays overview of System from
SMBIOS information.
SHOW BOOT
SHOW BOOT
Displays Primary Boot controller.
SHOW ACC
SHOW ACC
Displays Primary Array Controller
Configuration information.
Inspect CLI Commands 195
RBSU CLI Commands
The CLI mode of RBSU is a different interface that provides equivalent functionality to the menu-based
mode.
Command
Usage
Description
HELP
HELP or HELP <command>
Displays all supported commands or
usage and descriptions of a specific
command.
EXIT, QUIT
EXIT, QUIT
Exits RBSU and resets or power-cycles
system.
SHOW CONFIG
SHOW CONFIG
SHOW CONFIG displays all available
<options>.
SHOW CONFIG <option>
SHOW CONFIG <option> displays
current setting and all other setting
choices for <option> specified.
SHOW CONFIG SCRIPT displays the
script required to recreate the settings
of the server.
196
SHOW CONFIG OPTIONS
SHOW CONFIG OPTIONS
Displays list of CONFIG options that
are viewable or settable using SHOW
or SET CONFIG on this server.
SHOW CONFIG SCRIPT
SHOW CONFIG SCRIPT
Displays the script of SET commands
required to recreate all the server
system-related configuration settings.
Does not display script for Passwords,
Date/Time, or Serial Number.
SET CONFIG
SET CONFIG <choice> <option>
Sets CONFIG option setting to choice
specified by <choice> that corresponds
to the number of the choice listed by
SHOW CONFIG for that particular
option.
SHOW SN
SHOW SN
Displays current serial number value.
SET SN
SET SN <serial #>
Sets serial number to the value
specified.
SHOW BOOT
SHOW BOOT
Displays currently configured boot
controller order list.
SET BOOT
SET BOOT <controller #>
Sets new primary boot controller to
controller number in list displayed by
SHOW BOOT command, and then
displays the new list.
SET BOOT (alternate usage for
scripting)
SET BOOT <order #> <PCI
Vendor/DevID> <PCI Slot #> <PCI
Bus #> <PCI Device #> <PCI Fcn #>
Sets controller order # entry to device
specified by PCI ID and location. This
format is only used by SCRIPT driven
commands. Order # is 1-based where
1 is the primary boot controller, and so
on.
SHOW IPL
SHOW IPL
Displays current standard boot order
device list of IPL devices in priority
order.
SET IPL
SET IPL [A:|C:|CD|PXE] <new IPL
Priority>
Sets standard boot order priority for the
IPL device specified to new priority
number specified. The device specified
must be represented in the current IPL
list displayed by SHOW IPL.
RBSU BIOS Serial Console (CLI)
Command
Usage
Description
SHOW PCI
SHOW PCI
Displays a list of all PCI devices and
their current IRQ settings or disabled
status. Also, displays a list of IRQs
available for PCI devices to use.
SET PCI
SET PCI <device #> <IRQ>
Sets an override IRQ value (1-15) for
the PCI device selected, where <#>
corresponds to the number of the PCI
device in the list displayed by the
SHOW PCI command. Use 0 for the
<IRQ> value to disable a PCI device.
SET PCI (alternate usage for scripting) SET PCI <device #> <IRQ>
Sets an override IRQ value (1-15) for
the PCI device selected, where <#>
corresponds to the number of the PCI
device in the list displayed by the
SHOW PCI command. Use 0 for the
<IRQ> value to disable a PCI device.
SHOW SYS
SHOW SYS
Displays overview of System from
SMBIOS info.
SET PASSWORD POWERON
SET PASSWORD POWERON
Sets the Power-on password. Password
must be entered twice for verification
and must be seven characters or fewer.
SET PASSWORD ADMIN
SET PASSWORD ADMIN
Sets the Admin password. Password
must be entered twice for verification
and must be seven characters or fewer.
SHOW DATE
SHOW DATE
Displays date <mm/dd/yy>
SHOW TIME
SHOW TIME
Displays time <hh:mm>
SET DATE
SET DATE <mm/dd/yy>
Sets date to new value specified.
Century value assumed to be 20.
SET TIME
SET TIME <hh:mm>
Sets time to new value specified.
Seconds value is set to 0.
SHOW TEXT SERVER
SHOW TEXT SERVER
Displays current server info text strings.
SET TEXT SERVER
SET TEXT SERVER [N|A|P|O]
[1|2|3|4] <string>
Sets server info text string specified to
<string> where:
'N': Server Name (28)
"A': Server Asset Tag (32)
'P': Server Primary OS (42)
'O': Server Other (28)
# is the line number.
SHOW TEXT ADMIN
SHOW TEXT ADMIN
Displays current administrator contact
text strings.
SET TEXT ADMIN
SET TEXT ADMIN [N|P|G|O]
[1|2|3|4] <string>
Sets administrator contact text string
specified by <string> where:
'N': Admin name (28)
'P': Admin Phone number (28)
'G': Admin Pager number (28)
'O': Admin Other (28)
# is the line number.
SHOW TEXT SERVICE
SHOW TEXT SERVICE
Displays current service contact text
strings.
RBSU CLI Commands
197
Command
Usage
Description
SET TEXT SERVICE
SET TEXT SERVICE [N|P|G|O]
[1|2|3|4] <string>
Sets service contact text string specified
by <X> <#> to <string> where X can
be:
'N': Service Name (28)
'P': Service Phone number (28)
'G': Service Pager number (28)
'O': Service Other (28)
# is the line number.
SHOW TEXT IMD
SHOW TEXT IMD
Displays current IMD custom text strings.
SET TEXT IMD
SET TEXT IMD [I|M|S] [1|2|3|4]
<string>
Sets IMD Custom text string specified
by <X> <#> to <string> where:
'I': Idle Screen (48)
'M': Custom Menu Item (14)
'S': Custom Menu Screen (56)
# is the line number.
SHOW TEXT POST
SHOW TEXT POST
Displays current POST custom text
strings.
SET TEXT POST
SET TEXT POST <string>
Sets POST Custom text to string
specified by <string>.
System Maintenance CLI Commands
Command
Usage
Description
HELP
HELP or HELP <command>
Displays all supported commands or
usage and descriptions of a specific
command.
EXIT
EXIT
Exits menu and continues booting.
RBSU
RBSU
Executes RBSU (has CLI).
INSPECT
INSPECT
Executes Inspect Utility (has CLI).
PXE
PXE
Attempts PXE Boot.
MEMDIAG
MEMDIAG
Executes Diagnostics Utility specified.
(Diagnostics Utility also has CLI output.)
CPUDIAG
CPUDIAG
Executes Diagnostics Utility specified.
(Diagnostics Utility also has CLI output.)
DISKDIAG
DISKDIAG
Executes Diagnostics Utility specified.
(Diagnostics Utility also has CLI output.)
Command Buffering Support
The CLI mode support buffers the previous five commands entered from the command line, accessible
using the up arrow key and the down arrow key.
198 RBSU BIOS Serial Console (CLI)
Additional CLI support
The CLI mode support automatically handles output that scrolls off the screen by implementing a
-More- prompt at the bottom of the screen. Then, it waits for user input to scroll to the next page
of data using key commands.
Key
Function
Space
Scroll to next page
Enter
Scroll to next line
Q
Quit display
Additional CLI support 199
5 RBSU configuration flows (manual and scripted)
RBSU configuration flow overview
RBSU can be used in two ways to configure a server:
•
“Manual configuration flow” (page 200)
•
“Scripted configuration flow” (page 200)
Manual configuration flow
RBSU can be used to configure an HP server manually. When the server is powered up in an
unconfigured state, RBSU executes when the F9 key is pressed, allowing the server to be configured.
NOTE:
•
Manual flow does not apply for servers with an integrated ATA RAID IDE controller.
•
Manual flow is not necessary for servers with Embedded Server Setup.
After the server has been configured using RBSU:
1. Restart or power up the server.
2. Press the F8 key to execute ORCA.
3. After the primary array controller has been configured with ORCA, restart the server.
4. Install the operating system. (“Operating System Installation” (page 211))
5. Install any necessary applications.
6. Use HP SSA to configure any remaining array controllers.
Scripted configuration flow
RBSU can be used with the Scripting Toolkit (STK) to create standard server configuration scripts
to automate many of the manual steps in the server configuration process. The Scripting Toolkit
can be found on the HP website (http://www.hp.com/go/ProLiant/STK).
200 RBSU configuration flows (manual and scripted)
The following utilities are provided in the toolkit and described in this guide:
•
“Configuration Replication Utility (CONREP)” (page 201)
•
“HP ROM Configuration Utility (HPRCU)” (page 203)
•
“Array Configuration Replication Utility” (page 204)
Configuration Replication Utility (CONREP)
NOTE:
This utility is available for G7 and earlier servers.
Scripted configuration flow 201
CONREP is shipped in the Scripting Toolkit (STK) and is a program that works with RBSU to replicate
hardware configuration on ProLiant G7 and earlier servers. This utility is run during State 0, Run
Hardware Configuration Utility when doing a scripted server deployment. CONREP reads the state
of the system environment variables to determine the configuration and then writes the results to
an editable script file. This file can then be deployed across multiple servers with similar hardware
and software components. For more information, see the HP Scripting Toolkit User Guide for your
operating system environment on the HP website (http://www.hp.com/go/ProLiant/STK).
The following sections provide information on using CONREP scripts:
•
Backing up the existing configuration (“CONREP -s (Store to Data file) ” (page 202))
•
Restoring a configuration from a backup (“CONREP –l (Load from Data File)” (page 202))
CONREP -s (Store to Data file)
This is an example of usage for HP ProLiant servers not using the Oxx ROM family. To extract the
BIOS settings from an SL160z G6 server and save the configuration to an "sl160zconrep.dat"
data file:
[root@ilo002481b08134 conrep]# ./conrep -s -xconrepSL160zg6_20090728.xml -fsl160zconrep.dat
conrep 3.00 - Scripting Toolkit Configuration Replication Program
Copyright (c) 2007-2012 Hewlett-Packard Development Company, L.P.
System Type: ProLiant SL160z G6
ROM Date : 07/28/2009
ROM Family : O33
Processor Manufacturer : Intel
XML System Configuration : conrep_SL160zg6_20090728.xml
Hardware Configuration : sl160zconrep.dat
Saving configuration data to sl160zconrep.dat.
CONREP Return code: 0
NOTE:
The file names after the -x and -f options must be specified, otherwise, the default file
names conrep.xml and conrep.dat are used, respectively.
NOTE:
A platform specific XML file needs to be used for HP ProLiant 100-series servers. If you
use the default name this may cause an error while running the CONREP utility.
CONREP –l (Load from Data File)
This is an example of usage for HP ProLiant servers not using the Oxx ROM family. To load the
BIOS configuration settings from a previously captured/edited data file (in this case
“sl160zconrep.dat”) to an SL160z G6 server:
[root@ilo002481b08134 conrep]# ./conrep -l -xconrepSL160zg6_20090728.xml -fsl160zconrep.dat
conrep 3.00 - Scripting Toolkit Configuration Replication Program
Copyright (c) 2007-2012 Hewlett-Packard Development Company, L.P.
System Type: ProLiant SL160z G6
ROM Date : 07/28/2009
ROM Family : O33
Processor Manufacturer : Intel
XML System Configuration : conrep_SL160zg6_20090728.xml
Hardware Configuration : sl160zconrep.dat
Loading configuration from sl160zconrep.dat.
ASM values not set! aborting
CONREP Return code: 0
202 RBSU configuration flows (manual and scripted)
HP ROM Configuration Utility (HPRCU)
NOTE:
This utility is available for HP ProLiant Gen8 servers.
For more information, see the HP Scripting Toolkit User Guide for your operating system environment
on the HP website (http://www.hp.com/go/stk/docs).
Using HPRCU
HPRCU is an RBSU configuration utility similar to CONREP. This utility is supported on all HP
ProLiant Gen8 servers except the HP ProLiant DL580 Gen8 server. This utility does not use a
definition XML file like the CONREP utility, but directly reads the same table that RBSU uses for
feature names and settings. All features and options are number based. Each feature and option
has a unique number.
Using HPRCU has the following features:
•
All system ROM settings and the current selections are listed together in one output/input XML
file.
•
No updated binary or XML file is needed when BIOS adds or changes features. HPRCU now
reads the same tables that RBSU does, which are located in the memory at system boot. When
the BIOS changes or adds a new setting, no update to HPRCU is needed.
•
The HPRCU XML file shows the default settings for each RBSU option.
HPRCU is not supported on UEFI-based ProLiant servers. Instead, use CONREP.
HPRCU command-line syntax
hprcu -s | -l | —r [-f
file.xml ] [ -h ]
HPRCU command line arguments
Command line argument
Description
-s
This argument saves the system configuration to a file.
-l
This argument loads the system configuration from a file
and writes it to the target server.
-f {file.xml}
Name of the input or output file. If not specified, the XML
configuration defaults to hprcu.xml.
-h
This argument displays program usage.
-t
Outputs the help and warning text for each feature. Only
valid with the -s option.
-r
Saves or loads raw data features, such as IPL, PCI devices,
controller order) Must be applied to identical systems.
HPRCU return codes
Command line argument
Description
0
The command was completed successfully.
1
The server is not supported by this utility.
2
The input XML file is missing or is in an invalid format.
3
One of the dependencies is missing. See the error message
for details.
Scripted configuration flow 203
Command line argument
Description
4
The system RBSU password is set. The settings cannot be
changed until the password is cleared from within RBSU.
5
An error occurred reading the supported features on the
server.
6
Invalid command line syntax. Use the -h parameter for
complete command line parameters.
7
A general error occurred saving or loading the server
settings. See the error message for details.
Array Configuration Replication Utility
ACR is shipped in the Scripting Toolkit and is a replication utility used for RAID arrays. ACR is
used during State 0, Run Array Configuration Utility when doing a scripted server deployment. It
duplicates the host array controller configuration utilities and writes them onto an editable script
file. This file is then loaded onto a startup diskette for deployment to other servers.
204 RBSU configuration flows (manual and scripted)
6 ROM-based utilities
Some HP ProLiant servers have ROM-based enhancements available, including:
•
An auto-configuration process that, in most cases, automatically configures the entire system
without intervention.
•
The System Maintenance menu, which provides embedded server diagnostics and Inspect
Utility information through Embedded Server Setup.
•
An erase option for RBSU, which erases the system configuration and boot drive.
For more information about which features the server supports, see the server-specific documentation.
Embedded server setup
NOTE: Menu options may differ from those in this document, depending on specific server
options.
The System Maintenance menu is a utility that replaces the legacy system-partition functionality
supported on some ProLiant servers. This utility is embedded in the system ROM and provides
access to server diagnostics, RBSU, and the Inspect Utility.
To access the System Maintenance menu, press the F10 key when prompted from the boot option
screen (see “Boot options” (page 211)).
From the System Maintenance menu, you can select from the following utilities that are embedded
in the system ROM:
•
“Setup Utility” (page 206)
•
“Inspect Utility” (page 206)
•
“Diagnostics Utility” (page 207)
Embedded server setup 205
Setup Utility
Select Setup Utility from the System Maintenance menu to run the Setup Utility. Running Setup Utility
exits the System Maintenance menu and runs RBSU.
RBSU Erase option
The RBSU Erase option enables you to erase the system configuration and boot drive. On versions
of RBSU without this feature, the Erase Non-Volatile Memory option is available in the Advanced
Options menu of RBSU, enabling you to erase the system configuration by resetting the NVRAM
to an initial, factory state.
The Erase NVRAM/Boot Disk option also erases the system configuration by resetting the NVRAM,
but also erases the boot disk. The RBSU Erase option should only be used when you are redeploying
a server and are required to erase the NVRAM and boot drive to reinstall the operating system.
If available for the server, the Erase NVRAM/Boot Disk option is listed under the Advanced Options
menu in RBSU.
Virtual Install Disk option
The virtual install disk is a holding place within the system ROM that contains embedded boot
drivers (such as SCSI or RAID controller drivers) that may be necessary to complete the operating
system installation. Typically, boot drivers that are placed in the virtual install disk are either not
included as part of the operating system media or are updated for new controllers. Supported
operating systems automatically find these drivers, eliminating the need for user intervention. HP
recommends updating these boot drivers to the latest version after the OS install to further optimize
the system.
For more information, see:
•
G6 and earlier environments: “Virtual Install Disk” (page 184)
•
Gen8 and G7 environments: “Virtual Install Disk” (page 109)
The Virtual Install Disk option is found under the RBSU Advanced Options menu and can be enabled
or disabled in RBSU.
Inspect Utility
The Inspect Utility is embedded in the system ROM and enables you to view system configuration
information and save the information to a file on a diskette. Press the F2 key to place all Inspect
information onto a diskette.
This utility replaces the version of the Inspect Utility that is a part of the legacy system-partition
functionality supported on some HP servers.
If the server has the Inspect Utility feature, select Inspect Utility from the System Maintenance menu.
206 ROM-based utilities
Diagnostics Utility
The Diagnostics Utility is embedded in the system ROM, and provides a pre-boot method for quickly
checking the validity of the three major subsystems of the server needed to boot an operating
system.
All three of these tests should pass if a bootable operating system is installed on the server.
If any test fails, there may be a problem booting the server. To run the Diagnostics Utility, select
Diagnostics Utility from the System Maintenance menu.
Memory Test
The memory diagnostic test uses all the processors installed in the server to test all installed memory.
The DIMMs that are installed are displayed by the cartridge and socket (or the bank and socket)
in which they are located, and errors are reported with a reference to the failed DIMM.
To run the memory diagnostic test, select Memory Test from the Diagnostics Utility menu.
For a Generation 5 server with an Intel processor, the following options are available within the
Memory Test submenu:
•
Software Memory Test—Choosing this option automatically runs the test until completion or
until you press the Esc key to exit.
Embedded server setup 207
•
Quick MEMBIST Test—Choosing this option causes the system to reboot and run the
preconfigured hardware-based memory test. Upon reboot, Memory Diagnostics displays the
test results. A normal system reboot is required after performing a MEMBIST test.
•
User-defined MEMBIST Test—Choosing this option enables a user-defined configuration of the
Quick MEMBIST test. Increasing the MEMBIST test time results in a blank screen for the duration
of the test. Upon test completion and reboot, Memory Diagnostics displays the test results. A
normal system reboot is required after performing a MEMBIST test.
NOTE: To cancel either MEMBIST test, press and hold the Power On/Standby button to
initiate a forced shutdown. Upon reboot, no record of an incomplete test exists.
For all servers other than a Generation 5 server with an Intel processor, the Software Memory Test
automatically runs when Memory Test is selected from the Diagnostic Utility Menu.
CPU Test
The CPU diagnostic test checks the registers and MP capability of each processor. The test first
checks all the 16-bit and 32-bit registers, and then checks all the flags for all processors. If no
errors are found, OK is displayed under the Status column for each processor. If errors are found,
X is displayed under the Status column for each processor with errors.
To run the CPU diagnostic test, select CPU Test from the Diagnostics Utility menu.
208 ROM-based utilities
Boot Disk Test
The boot disk diagnostic test verifies the presence and readiness of a primary boot controller. If a
controller is present and ready, the test checks for a valid operating system boot sector.
To run the Boot Disk diagnostic test, select Boot Disk Test from the Diagnostics Utility menu.
Auto-Configuration Process
The auto-configuration process automatically runs when you boot the server for the first time. During
the power-up sequence, in many cases the system ROM automatically configures the entire system
without needing any intervention. During this process, the ORCA Utility, in most cases, automatically
configures the array with a default setting based on the number of drives connected to the server.
Drives installed
Drives used
RAID level
1
1
RAID 0
2
2
RAID 1
3, 4, 5, or 6
3, 4, 5, or 6
RAID 5
More than 6
0
None
NOTE: If the boot drive contains logical volumes, or if more than six drives are installed on the
system, ORCA does not automatically configure the array. If this occurs, you must run ORCA to
configure the array settings.
By default, the auto-configuration process configures the system for a default operating system. To
change any default settings in the auto-configuration process, such as the settings for language,
operating system, and primary boot controller, open the RBSU by pressing the F9 key after system
POST. After the settings are selected according to your preference, exit RBSU and reboot the server.
Intelligent Provisioning Quick Configs settings and corresponding RBSU
settings
Available for HP ProLiant Gen8 servers, Intelligent Provisioning Quick Configs options provide the
capability to select a basic policy for performance versus power usage, without having to configure
individual settings through RBSU menus.
The following tables show the three Intelligent Provisioning Quick Configs profiles and their
corresponding RBSU option settings.
Auto-Configuration Process 209
NOTE: Not all of the options in this table are adjustable on all servers. However, even if you do
not have the option of adjusting some of these settings, they will default to the values shown here.
Intelligent Provisioning Quick Configs settings (AMD-based servers)
RBSU power management
options
Balanced power and
performance
“HP Power Profile” (page
45)
Balanced Power and
Performance
“HP Power Regulator” (page HP Dynamic Power Savings
46)
Mode
Minimum power usage
Maximum performance
Minimum Power Usage
Maximum Performance
HP Static Low Power Mode
HP Static High Performance
Mode
“Minimum Processor Idle
Power Core C6 State” (page
53)
Enabled
Enabled
Disabled
“Minimum Processor Idle
Power C1e State” (page 54)
Disabled
Enabled
Disabled
Auto
Auto
Auto
Channel Interleaving
No Interleaving
Channel Interleaving
“PCI Express Generation 2.0
Support” (page 61)
Auto
Force PCIe Generation 1
Auto
“HyperTransport Frequency”
(page 71)
HT Full Performance Mode
HT Power Saving Mode
HT Full Performance Mode
“Dynamic Power Savings
Mode Response” (page 64)
Fast
Slow
Fast
“DIMM Voltage Preference”
(page 69)
Optimized for Performance
Optimized for Power
Optimized for Performance
“Maximum Memory Bus
Frequency” (page 58)
“Memory Interleaving”
(page 60)
Intelligent Provisioning Quick Configs settings (Intel-based servers)
RBSU power management
options
Balanced power and
performance
Minimum power usage
Maximum performance
“HP Power Profile” (page
45)
Balanced Power and
Performance
Minimum Power Usage
Maximum Performance
HP Static Low Power Mode
HP Static High Performance
Mode
“HP Power Regulator” (page HP Dynamic Power Savings
46)
Mode
“Intel QPI Link Power
Management” (page 49)
Enabled
Enabled
Disabled
“Minimum Processor Idle
Power Core State” (page
52)
C6 State
C6 State
No C-states
“Minimum Processor Idle
Package C6 (retention) State Package C6 (retention) State
Power Package State” (page
55)
“Energy/Performance Bias”
(page 57)
“Maximum Memory Bus
Frequency” (page 58)
210
ROM-based utilities
No Package State
Balanced Performance
Power Savings Mode
Maximum Performance
Auto
Auto
Auto
Intelligent Provisioning Quick Configs settings (Intel-based servers)
RBSU power management
options
Balanced power and
performance
Minimum power usage
Maximum performance
“Channel Interleaving”
(page 59)
Enabled
Disabled
Enabled
“Maximum PCI Express
Speed” (page 63)
Maximum Supported
PCIe Generation 1
Maximum Supported
Optimized for Performance
Optimized for Power
Optimized for Performance
“DIMM Voltage Preference”
(page 69)
Boot options
Near the end of the boot process, the boot options screen is displayed. This screen is visible for
several seconds before the system attempts to boot from a supported boot device. During this time,
you can press the following keys:
Key
Action
F9
Access RBSU.
F10
In Gen8 systems: Access Intelligent Provisioning. In G7 systems: Access the System
Maintenance Menu, which enables you to launch ROM-based Diagnostics or Inspect.
F12
Force a PXE Network boot.
Operating System Installation
For an assisted operating system installation:
•
In Gen8 environments, boot the server and press F10 when prompted to open the Intelligent
Provisioning tool.
•
In G7 environments, insert the SmartStart CD into the CD-ROM drive to begin the installation
process. The operating system and server support software are installed upon completion of
this process.
For a manual OS installation, insert the operating system CD into the CD-ROM to begin the
installation process.
Boot options
211
7 Support and other resources
Information to collect before contacting HP
Be sure to have the following information available before you contact HP:
•
Software product name
•
Hardware product model number
•
Operating system type and version
•
Applicable error message
•
Third-party hardware or software
•
Technical support registration number (if applicable)
How to contact HP
Use the following methods to contact HP technical support:
•
See the Contact HP worldwide website:
http://www.hp.com/go/assistance
•
Use the Contact hp link on the HP Support Center website:
http://www.hp.com/go/hpsc
•
In the United States, call +1 800 334 5144 to contact HP by telephone. This service is available
24 hours a day, 7 days a week. For continuous quality improvement, conversations might be
recorded or monitored.
Subscription service
Receive, by email, support alerts announcing product support communications, driver updates,
software releases, firmware updates, and customer-replaceable component information by signing
up at http://www.hp.com/go/myadvisory.
To change options for support alerts you already receive, click the Sign in link on the right.
Related information
The following HP websites provide access to HP product information and user documents:
212
•
HP BladeSystem: http://www.hp.com/go/bladesystem
•
HP Servers: http://www.hp.com/go/servers
•
HP Converged Network Adapters (CNA): http://www.hp.com/go/cna
•
HP Infrastructure products: http://www.hp.com/go/infrastructure
•
HP ProLiant Networking: http://www.hp.com/servers/networking
•
iLO: http://www.hp.com/go/ilo
•
Intelligent Provisioning: http://www.hp.com/go/intelligentprovisioning
•
Scripting Toolkit (STK): http://www.hp.com/go/ProLiantSTK
Support and other resources
•
HP Single Point of Connectivity Knowledge (SPOCK): http://www.hp.com/storage/spock
•
HP Support:
◦
Main menu: http://www.hp.com/support
◦
Downloads: http://www.hp.com/support/downloads
◦
User documents: http://www.hp.com/support/manuals
Typographic conventions
Table 1 Document conventions
Convention
Element
Blue text: Table 1 (page 213)
Cross-reference links and e-mail addresses
Blue, underlined text: http://www.hp.com
Website addresses
Bold text
• Keys that are pressed
• Text typed into a GUI element, such as a box
• GUI elements that are clicked or selected, such as menu
and list items, buttons, tabs, and check boxes
Italic text
Text emphasis
Monospace text
• File and directory names
• System output
• Code
• Commands, their arguments, and argument values
Monospace, italic text
• Code variables
• Command variables
Monospace, bold text
WARNING!
CAUTION:
IMPORTANT:
NOTE:
Emphasized monospace text
Indicates that failure to follow directions could result in bodily harm or death.
Indicates that failure to follow directions could result in damage to equipment or data.
Provides clarifying information or specific instructions.
Provides additional information.
HP Insight Remote Support
HP strongly recommends that you register your device for remote support to enable enhanced
delivery of your HP Warranty, HP Care Pack Service, or HP contractual support agreement. HP
Insight Remote Support supplements your monitoring continuously to ensure maximum system
availability by providing intelligent event diagnosis, and automatic, secure submission of hardware
event notifications to HP, which will initiate a fast and accurate resolution, based on your product’s
service level. Notifications can be sent to your authorized HP Channel Partner for onsite service,
if configured and available in your country.
For more information, see HP Insight Remote Support and Insight Online Setup Guide for ProLiant
Servers and BladeSystem c-Class Enclosures on the HP website (http://www.hp.com/go/enterprise/
Typographic conventions
213
docs). HP Insight Remote Support is available as part of HP Warranty, HP Care Pack Service, or
HP contractual support agreement.
HP Insight Online direct connect
When you use the embedded Remote Support functionality with an HP ProLiant Gen8 or Gen9
server or HP BladeSystem c-Class enclosure, you can register a server or enclosure to communicate
directly to HP Insight Online without the need to set up an HP Insight Remote Support centralized
Hosting Device in your local environment. HP Insight Online will be your primary interface for
remote support information.
The Insight Online direct connect configuration is available in iLO 4 1.40 and later, Intelligent
Provisioning 1.60 and later, and Onboard Administrator 4.11 and later.
For more information, see the product documentation on the HP website: http://www.hp.com/
go/insightremotesupport/docs.
HP Insight Remote Support central connect
When you use the embedded Remote Support functionality with an HP ProLiant Gen8 or Gen9
server or HP BladeSystem c-Class enclosure, you can register a server or enclosure to communicate
to HP through an HP Insight Remote Support centralized Hosting Device in your local environment.
All configuration and service event information is routed through the Hosting Device. This information
can be viewed by using the local HP Insight RS user interface or the web-based view in HP Insight
Online.
The Insight Remote Support central connect configuration is available in iLO 4 1.10 and later,
Intelligent Provisioning 1.20 and later, and Onboard Administrator 3.60 and later.
For more information, see the product documentation on the HP website: http://www.hp.com/
go/insightremotesupport/docs.
HP Insight Online
HP Insight Online is a capability of the HP Support Center portal. Combined with HP Insight Remote
central connect or HP Insight Online direct connect, it automatically aggregates device health,
asset, and support information with contract and warranty information, and then secures it in a
single, personalized dashboard that is viewable from anywhere at any time. The dashboard
organizes your IT and service data to help you understand and respond to that information more
quickly. With specific authorization from you, an authorized HP Channel Partner can also view
your IT environment remotely by using HP Insight Online.
For more information, see the following documents on the HP website (http://www.hp.com/go/
insightremotesupport/docs):
214
•
HP Insight Online User’s Guide
•
HP Insight Remote Support and Insight Online Setup Guide for ProLiant Servers and BladeSystem
c-Class Enclosures
Support and other resources
8 Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the
documentation, send any errors, suggestions, or comments to Documentation Feedback
(docsfeedback@hp.com). Include the document title and part number, version number, or the URL
when submitting your feedback.
215
Acronyms and abbreviations
ACR
Array Configuration Replication utility
ASR
Automatic Server Recovery
CNA
Converged Network Adapter
CONREP
Configuration Replication utility
ECP
Extended Capabilities Port Mode
EMS
Emergency Management Services
EPP
Enhanced Parallel Port Mode
IDE
Integrated Device Electronics
iLO
Integrated Lights-Out
IMD
Integrated Management Display
IOMMU
I/O Memory Management Unit
IPL
Initial Program Load
IRQ
Interrupt Request
LPT
Local Port
MEMBIST
Memory Built-in Self Test
MPS
Multi-Processor Specification
NMI
Non-Maskable Interrupt
NUMA
Non-Uniform Memory Architecture
NVRAM
Non-Volatile Memory
ORCA
Option ROM Configuration for Arrays
PCC
Processor Clocking Control
PCI-X
Peripheral Component Interconnect extended
PCIe
Peripheral Component Interconnect express
POST
Power-On Self Test
PXE
Preboot Execution Environment
RBSU
ROM-Based Setup Utility
RTC
Real-Time Clock
SPP
Standard Parallel Port Mode
TPM
Trusted Platform Module
VSP
Virtual Serial Port
216
Acronyms and abbreviations
Index
Symbols
1333 MHz Support for 3DPC-10600H HP SmartMemory
Gen8 servers, 140
250MB partition, 206
G5 through Gen8 servers, 109
G5/earlier servers, 184
A
ACPI SLIT Preferences
Gen8 servers, 67
additional CLI support, 199
Address Mode 44-bit
G7 servers, 112
Adjacent Sector Prefetch
G5 through Gen8 servers, 128
G5/earlier servers, 186
Administrator Info Text
G5 through Gen8 servers, 101
Advanced Memory Protection
G5 through Gen8 servers, 18
G5/earlier servers, 163
Advanced Options menu
G5 through Gen8 servers, 104
G5/earlier servers, 181
Advanced Performance Tuning Options
G5 through Gen8 servers, 126
Advanced Power Management Options
G5 through Gen8 servers, 48
Advanced System ROM options
G5 through Gen8 servers, 104
AMD Core Performance Boost
G5 through Gen8 servers, 36
AMD V (AMD Virtualization)
G5 through Gen8 servers, 29
AMD-Vi (IOMMU)
Gen8 servers, 38
Array Configuration Replication Utility (ACR), 204
ASR Status
G5 through Gen8 servers, 78
G5/earlier servers, 171
ASR Timeout
G5 through Gen8 servers, 79
G5/earlier servers, 171
Asset Tag Protection
G5 through Gen8 servers, 150
auto-configuration process, 209
Automatic Power-On
G5/earlier servers, 172
G7 servers, 84
Gen8 servers, 85
G5 through Gen8 servers, 99
G5/earlier servers, 179
BIOS Serial Console & EMS
Command Line Interface overview, 189
G5 through Gen8 servers, 95
G5/earlier servers, 175
BIOS Serial Console Baud Rate
G5 through Gen8 servers, 97
G5/earlier servers, 176
BIOS Serial Console Port
G5 through Gen8 servers, 96
G5/earlier servers, 176
Boot Controller Order
G5 through Gen8 servers, 76
G5/earlier servers, 170
Boot Disk diagnostic test, 209
boot options, 211
C
Channel Interleaving
Gen8 servers, 59
Collaborative Power Control
G7 and Gen8 servers, 65
Command Buffering Support, 198
Command Line Interface (CLI)
additional CLI support, 199
overview, 189
configuration flow, 200
Configuration Replication Utility, 201
CONREP, 201
Load from Data file example
HP ProLiant 100 series, 202
Store to Data file example
HP ProLiant 100 series, 202
Consistent Device Naming
Gen8 servers, 115
contacting HP, 212
conventions
document, 213
text symbols, 213
core disabling options, 33
Core Performance Boost
G5 through Gen8 servers, 36
CPU Cache Stride Prefetcher
G5 through Gen8 servers, 137
CPU Core Hardware Prefetcher
G7 and Gen8 servers, 136
CPU diagnostic test, 208
Custom POST Message
G5 through Gen8 servers, 103
G5/earlier servers, 181
B
D
BIOS Enhanced RAID
G5/earlier servers, 184
BIOS Interface Mode
Data Direct I/O
Gen8 servers, 141
Data Reuse
217
G7 servers, 132
Date and Time
G5 through Gen8 servers, 77
G5/earlier servers, 170
DCU IP Prefetcher
Gen8 servers, 131
DCU Prefetcher
G5 through Gen8 servers, 129
DCU Streamer Prefetcher
Gen8, 130
Diagnostics Utility, 207
DIMM Idle Power Saving Mode
G7 servers, 68
DIMM Voltage Preference
G5 through Gen8 servers, 69
Diskette Boot Control
G5/earlier servers, 162
Diskette Write Control
G5/earlier servers, 162
document
conventions, 213
documentation
HP website, 212
providing feedback on, 215
DRAM Prefetch on CPU Request
G7 and Gen8 servers, 134
DRAM Prefetch on I/O Request
G7 and Gen8 servers, 135
Drive Write Cache
G5/earlier servers, 185
G7 servers, 149
Gen8 servers, 43
Dynamic Power Capping Functionality
Gen8 servers, 72
Dynamic Power Savings Mode Response
G5 through Gen8 servers, 64
E
Embedded NIC PXE Support option
G5/earlier servers, 162
Embedded NICs
G5 through Gen8 servers, 16
Embedded SATA Configuration
Gen8 servers, 42
Embedded SATA RAID
G6 and G7 servers, 152
Embedded Serial Port
G5 through Gen8 servers, 12
Embedded Serial Port A option
G5/earlier servers, 159
Embedded Serial Port B option
G5/earlier servers, 160
Embedded Serial Port Connector
Gen8 servers, 15
Embedded server Setup, 205
Embedded VGA Control
G5/earlier servers, 187
EMS Console
G5 through Gen8 servers, 98
218
Index
G5/earlier servers, 178
Energy/Performance Bias
Gen8 servers, 57
Enhanced Processor Core Disable (Intel Core Select)
G7 and Gen8 servers, 31
Expansion Card Caching Optimization
G5/earlier servers, 186
F
F10 Prompt, disabling, 90
F11 Boot Menu Prompt
Gen8 servers, 114
H
Hardware Prefetch training on Software Prefetch
G7 servers, 133
help
obtaining, 212
Hemisphere Mode
G7 servers, 144
Hide Option ROM Messages
G5 through Gen8 servers, 117
HP
subscription service, 212
technical support, 212
HP Insight Online, 214
HP Option ROM Prompting
Gen8 servers, 120
HP Power Profile
G5 through Gen8 servers, 45
HP Power Regulator
G5 through Gen8 servers, 46
HP ROM Configuration Utility, 203
HP Smart Array B320i RAID Configuration
Gen8 servers, 44
HPC Optimization Mode
G7 servers, 145
HPRCU, 203
arguments, 203
command-line syntax, 203
return codes, 203
HW Prefetcher
G5 through Gen8 servers, 127
G5/earlier servers, 186
HyperTransport Frequency
G5 through Gen8 servers, 71
I
Inspect CLI commands, 195
Inspect Utility, 206
Integrated Diskette Controller option
G5/earlier servers, 161
Intel Hyperthreading Options
G5 through Gen8 servers, 30
Intel Performance Counter Monitor (PCM)
G7 and Gen8 servers, 146
Intel QPI Link Frequency
Gen8 servers, 50
Intel QPI Link Power Management
G5 through Gen8 servers, 49
Intel Turbo Boost Technology
G7 servers, 35
Gen8 servers, 34
Intel Virtualization Technology
G5 through Gen8 servers, 28
G5/earlier servers, 186
Intel VT-d
G5 through Gen8 servers, 37
Intelligent Provisioning (F10 Prompt)
Gen8 servers, 90
Intelligent Provisioning, disabling, 90
IPL Boot Order
G5 through Gen8 servers, 75
G5/earlier servers, 169
M
manual configuration flow, 200
Maximum Memory Bus Frequency
G5 through Gen8 servers, 58
Maximum PCI Express Speed
Gen8 servers, 63
Memory Channel Mode
Gen8 servers, 142
Memory Interleaving
G5 through Gen8 servers, 60
Memory Mapped I/O Options
G7 servers, 111
Memory Power Savings Mode
Gen8 servers, 70
Memory Speed
G7 servers, 143
Memory Test, 207
Minimum Processor Idle Power C1e State
Gen8 servers, 54
Minimum Processor Idle Power Core C6 State
Gen8 servers, 53
Minimum Processor Idle Power Core State
G5 through Gen8 servers, 52
Minimum Processor Idle Power Package State
G5 through Gen8 servers, 55
Minimum Processor Idle Power State
G7 servers, 56
MPS Table Mode
G5 through Gen8 servers, 106
MPS table mode
G5/earlier servers, 182
Multi-Processor Specification (MPS) Table Mode
G5/earlier servers, 182
N
Network Boot Retry Support
Gen8 servers, 116
Network Server Mode (HP ProLiant DL360 and HP ProLiant
DL380)
G7 servers, 89
Network Server Mode option
G5/earlier servers, 175
NIC Personality Options
G5 through Gen8 servers, 17
NMI Debug Button option
G5 through Gen8 servers, 108
G5/earlier servers, 184
No-Execute Memory Protection
G5 through Gen8 servers, 26
G5/earlier servers, 186
No-Execute Page Protection
G5 through Gen8 servers, 27
Node Interleaving
G5 through Gen8 servers, 139
G5/earlier servers, 184
NUMLOCK Power-On State
G5 through Gen8 servers, 41
NUMLOCK Power-On State option
G5/earlier servers, 161
O
One Terabyte Memory Limit
G7 and Gen8 servers, 148
operating system installation, 211
Option ROM Loading Sequence
G7 servers, 105
Optional LPT Mode Support
G5/earlier servers, 161
Optional PCI-X Riser Fan Monitoring
G5/earlier servers, 185
OS Installation, 211
overview, 9
P
PCI Bus Padding Options
G5 through Gen8 servers, 110
PCI Devices
G5 through Gen8 servers, 74
G5/earlier servers, 168
PCI Express Generation 2.0 Support
G5 through Gen8 servers, 61
PCI IRQ settings
G5 through Gen8 servers, 73
PCI-X Riser Fan Monitoring
G5/earlier servers, 185
PCIe Gen 3 Control
Gen8 servers, 62
PCIe Slot6 Training Speed
G5 through Gen8 servers, 118
POST F1 Prompt
G5 through Gen8 servers, 82
G5/earlier servers, 172
POST speed up
G5/earlier servers, 171
Power Button
G5 through Gen8 servers, 83
G5/earlier servers, 172
Power Capping Support
Gen8 servers, 66
Power Management Option menu
G5 through Gen8 servers, 45
Power Regulator for ProLiant
219
G5/earlier servers, 165
power settings
profiles, 209
Power Supply Requirements Override
G5/earlier servers, 186
G7 servers, 122
Power-On Delay
G5/earlier servers, 172
G7 servers, 86
Power-On Logo
G5 through Gen8 servers, 113
Processor Core Disable
G7 and Gen8 servers, 33
Processor Core Disable (Intel Core Select)
Gen8 servers, 32
Processor Hyper-Threading
G5/earlier servers, 185
Processor Hyperthreading
G5 through Gen8 servers, 30
Processor Options
G5 through Gen8 servers, 25
G5/earlier servers, 185
Product ID
G5 through Gen8 servers, 125
G5/earlier servers, 185
profiles
power settings, 209
Q
QPI Bandwidth Optimization (RTID)
Gen8 servers, 51
QuickLock option
G5/earlier servers, 175
R
RBSU
running, 9
RBSU CLI commands, 196
RBSU configuration flow, 200
RBSU Erase option, 206
RBSU menu
G5 through Gen8 servers, 11
RBSU menu (G5/earlier servers)
overview, 158
Redundant Power Supply Mode
G5 through Gen8 servers, 47
Remote Console Mode
G5 through Gen8 servers, 39
Removable Flash Media Boot Sequence
G5 through Gen8 servers, 23
Reset on Boot Device Not Found
Gen8 servers, 119
Restore Default System Settings
G5 through Gen8 servers, 153
G5/earlier servers, 183
Restore Settings/Erase Boot Disk
G5 through Gen8 servers, 154
G5/earlier servers, 183
ROM Selection option
220 Index
G5 through Gen8 servers, 107
G5/earlier servers, 182
ROM-based utilities, 205
S
SATA Controller Options
Gen8 , 42
SATA software RAID
G5/earlier servers, 185
Scripted configuration flow, 200
scripted flow, 204
Secondary IDE Channel Support option
G5/earlier servers, 184
Serial Number
G5 through Gen8 servers, 124
G5/earlier servers, 185
serial port 1, 12
Serial Port options
G5 through Gen8 servers, 12
Server Asset Text
G5 through Gen8 servers, 100
G5/earlier servers, 179
Server Availability
G5 through Gen8 servers, 78
G5/earlier servers, 170
Server Info Text
G5 through Gen8 servers, 100
Server Passwords menu
G5 through Gen8 servers, 87
G5/earlier servers, 172
server security
G5 through Gen8 servers, 87
Service Contact Text
G5 through Gen8 servers, 102
Service Options
G5 through Gen8 servers, 124
Set Admin Password
G5 through Gen8 servers, 88
G5/earlier servers, 173
Set Administrator Info Text
G5/earlier servers, 179
Set Power-On Password
G5 through Gen8 servers, 87
G5/earlier servers, 173
Set Server Info Text
G5/earlier servers, 179
Set Service Contact Text
G5/earlier servers, 180
Setup Utility, 206
SR-IOV
Gen8 servers, 151
Stack Engine Prediction
G7 and Gen8 servers, 138
Standard Boot Order (IPL)
G5 through Gen8 servers, 75
G5/earlier servers, 169
subscription service, HP, 212
symbols in text, 213
System Default Options
G5 through Gen8 servers, 153
System Locality Information Table
G7 and Gen8 servers, 146
System Maintenance CLI commands, 198
System Maintenance menu, 205
System Options menu
G5 through Gen8 servers, 12
G5/earlier servers, 158
T
technical support
HP, 212
text symbols, 213
Thermal Configuration
G5 through Gen8 servers, 123
Thermal Shutdown
G5 through Gen8 servers, 80
G5/earlier servers, 171
TPM (Trusted Platform Module)
G5/earlier servers, 173
TPM Clear
G5 through Gen8 servers, 94
G5/earlier servers, 175
TPM Expansion ROM Measuring
G5 through Gen8 servers, 93
G5/earlier servers, 174
TPM Functionality
G5 through Gen8 servers, 91
G5/earlier servers, 174
TPM Visibility
G5 through Gen8 servers, 92
G5/earlier servers, 174
Trusted Platform Module (TPM)
G5 through Gen8 servers, 91
G5/earlier servers, 173
turbo mode
G7 servers, 35
Gen8 servers, 34
typographic conventions, 213
G5 through Gen8 servers, 155
G5/earlier servers, 183
Utility Language
G5 through G7 servers, 156
G5/earlier servers, 188
Gen8 servers, 157
V
Video Options
G5 through Gen8 servers, 121
Virtual Install Disk, 206
G5 through Gen8 servers, 109
G5/earlier servers, 184
Virtual Serial Port
G5 through Gen8 servers, 14
G5/earlier servers, 161
W
Wake-On LAN (WOL)
G5 through Gen8 servers, 81
G5/earlier servers, 171
web sites
HP subscription service, 212
websites
product manuals, 212
product pages, 212
U
Ultra Low Power State
G5/earlier servers, 167
USB 2.0 Controller
G5 through Gen8 servers, 21
USB 2.0 EHCI Controller
G5/earlier servers, 164
USB Boot Support
Gen8 servers, 22
USB Control
G5 through Gen8 servers, 20
G5/earlier servers, 164
USB Drive Key Enumeration
Gen8 servers, 23
USB External Port Capability
G5/earlier servers, 166
USB Options
G5 through Gen8 servers, 19
User Default Options
221
Download PDF
Similar pages
null 9448077
HP One Button Disaster Recovery SW Reference Guide
HP SmartDrive for ProLiant Gen8 servers - Data
HPServersG8 سایز فایل : 347.7 KB