ENGLISH: Original instructions
INSTRUCTION MANUAL
Rotary Hammer
HR3200C
HR3210C
HR3210FCT
DOUBLE INSULATION
Read before use.
SPECIFICATIONS
Model
Capacities
HR3200C
Concrete
HR3210C
Tungsten-carbide
tipped bit
32 mm
Core bit
90 mm
Steel
HR3210FCT
13 mm
Wood
32 mm
No load speed (min-1)
315 - 630
Blows per minute
1,650 - 3,300
Overall length
398 mm
Net weight
4.8 kg
Safety class
424 mm
5.2 kg
5.4 kg
/II
• Due to our continuing programme of research and development, the speciications herein are subject to change
without notice.
• Speciications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment. Be sure that you understand their meaning before
use.
Read instruction manual.
DOUBLE INSULATION
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Intended use
The tool is intended for hammer drilling in brick, concrete and stone as well as for chiselling work.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Noise
The typical A-weighted noise level determined according to EN60745:
Model HR3200C,HR3210C
Sound pressure level (LpA) : 89 dB (A)
Sound power level (LWA) : 100 dB (A)
Uncertainty (K) : 3 dB (A)
Model HR3210FCT
Sound pressure level (LpA) : 88 dB (A)
Sound power level (LWA) : 99 dB (A)
Uncertainty (K) : 3 dB (A)
Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745:
Model HR3200C
Work mode : hammer drilling into concrete
Vibration emission (ah,HD) : 18.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode : chiselling
Vibration emission (ah,CHeq) : 12.5 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: drilling into metal
2
Vibration emission (ah,D) : 2.5 m/s or less
Uncertainty (K) : 1.5 m/s2
Model HR3210C
Work mode : hammer drilling into concrete
Vibration emission (ah,HD) : 10.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode : chiselling
Vibration emission (ah,CHeq) : 7.5 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
Model HR3210FCT
Work mode : hammer drilling into concrete
Vibration emission (ah,HD) : 10.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode : chiselling
Vibration emission (ah,CHeq) : 8.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
Wear ear protection
2
ENGLISH
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiied plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30 mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inluence of drugs, alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your inger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
17. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WARNING: The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s):
Designation of Machine:
Rotary Hammer
Model No./ Type: HR3200C,HR3210C,HR3210FCT
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30.1.2009
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may
result in electric shock, ire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of lammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
3
ENGLISH
5.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
Service
25. Have your power tool serviced by a qualiied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
26. Follow instruction for lubricating and changing accessories.
27. Keep handles dry, clean and free from oil and
grease.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Be sure the bit is secured in place before
operation.
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for
a while by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is dificult.
Always be sure you have a irm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool irmly with both hands.
Keep hands away from moving parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not point the tool at any one in the area
when operating. The bit could ly out and
injure someone seriously.
Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier
safety data.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from repeated
use) replace strict adherence to safety
rules for the subject product. MISUSE or
failure to follow the safety rules stated in
this instruction manual may cause serious
personal injury.
ROTARY HAMMER SAFETY
WARNINGS
1.
2.
3.
4.
Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recommended that you wear a dust mask and thickly
padded gloves.
4
ENGLISH
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of
lamp. Be careful not to scratch the lens of lamp,
or it may lower the illumination.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Speed change
Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.
Switch action
1
► 1. Adjusting dial
1
The revolutions and blows per minute can be adjusted
just by turning the adjusting dial. The dial is marked 1
(lowest speed) to 5 (full speed).
Refer to the table below for the relationship between the
number settings on the adjusting dial and the revolutions/blows per minute.
► 1. Switch trigger
CAUTION:
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Number on
adjusting dial
Revolutions per
minute
Blows per minute
5
4
3
2
1
630
590
480
370
315
3,300
3,100
2,500
1,900
1,650
Lighting up the lamps
CAUTION:
•
For Model HR3210FCT
•
If the tool is operated continuously at low
speeds for a long time, the motor will get overloaded, resulting in tool malfunction.
The speed adjusting dial can be turned only as
far as 5 and back to 1. Do not force it past 5 or
1, or the speed adjusting function may no longer
work.
1
► 1. Lamp
CAUTION:
•
Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
5
ENGLISH
Changing the quick change chuck
for SDS-plus
Selecting the action mode
Rotation with hammering
For Model HR3210FCT
The quick change chuck for SDS-plus can be easily
exchanged for the quick change drill chuck.
1
Removing the quick change chuck
for SDS-plus
2
1
2
1
3
2
► 1. Lock button 2. Pointer 3. Change lever
For drilling in concrete, masonry, etc., depress the lock
button and rotate the change lever so that the pointer
points to the
symbol. Use a tungsten-carbide tipped
bit.
3
Rotation only
► 1. Quick change chuck for SDS-plus 2. Change
cover 3. Chuck cover
CAUTION:
•
2
Before removing the quick change chuck for
SDS-plus always remove the bit.
Hold the change cover with the thumb and the middle inger and pull it in the direction arrow 1. With the
change cover pulled in that direction, hold the chuck
cover with the index inger. While holding the chuck
cover so, pull out the quick change chuck for SDS-plus
in the direction of arrow 2 at a stroke.
3
1
Attaching the quick change drill
chuck
► 1. Lock button 2. Change lever 3. Pointer
For drilling in wood, metal or plastic materials, depress
the lock button and rotate the change lever so that the
pointer points to the symbol. Use a twist drill bit or
wood bit.
1
Hammering only
3
2
1
► 1. Spindle 2. Quick change drill chuck 3. Change
cover
Grasp the change cover and place the quick change
drill chuck on the spindle of the tool.
Make sure that the quick change drill chuck is secured
by trying to pull it several times.
2
► 1. Pointer 2. Change lever 3. Lock button
6
ENGLISH
3
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the symbol. Use a bull point, cold
chisel, scaling chisel, etc.
ASSEMBLY
CAUTION:
•
CAUTION:
•
Do not rotate the change lever when the tool is
running under load. The tool will be damaged.
To avoid rapid wear on the mode change mechanism, be sure that the change lever is always
positively located in one of the three action
mode positions.
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Side grip
1
Torque limiter
The torque limiter will actuate when a certain torque
level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning.
CAUTION:
•
As soon as the torque limiter actuates, switch
off the tool immediately. This will help prevent
premature wear of the tool.
Indicator lamp
► 1. Side grip
CAUTION:
1
•
Always use the side grip to ensure operating
safety when drilling in concrete, masonry, etc.
The side grip swings around to either side, allowing
easy handling of the tool in any position. Loosen the
side grip by turning it counterclockwise, swing it to the
desired position and then tighten it by turning clockwise.
Installing or removing the bit
2
► 1. Power-ON indicator lamp (green) 2. Service
indicator lamp (red)
1
The green power-ON indicator lamp lights up when the
tool is plugged. If the indicator lamp does not light up,
the mains cord or the controller may be defective. The
indicator lamp is lit but the tool does not start even if the
tool is switched on, the carbon brushes may be worn
out, or the controller, the motor or the ON/OFF switch
may be defective.
The red service indicator lamp lights up when the carbon brushes are nearly worn out to indicate that the tool
needs servicing. After approx. 8 hours of use, the motor
will automatically be shut off.
2
► 1. Bit shank 2. Bit grease
Clean the bit shank and apply bit grease before installing the bit.
Insert the bit into the tool. Turn the bit and push it in until
it engages.
7
ENGLISH
The bit can be secured at 24 different angles. To change
the bit angle, depress the lock button and rotate the
change lever so that the pointer points to the symbol.
Turn the bit to the desired angle.
Depress the lock button and rotate the change lever so
that the pointer points to the symbol. Then make sure
that the bit is securely held in place by turning it slightly.
1
2
Depth gauge
2
1
► 1. Bit 2. Chuck cover
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages.
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
► 1. Depth gauge 2. Clamp screw
1
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the clamp screw and adjust
the depth gauge to the desired depth. After adjusting,
tighten the clamp screw irmly.
2
NOTE:
•
The depth gauge cannot be used at the position
where the depth gauge strikes against the gear
housing/motor housing.
Dust cup
► 1. Bit 2. Chuck cover
Bit angle (when chipping, scaling or
demolishing)
1
1
2
► 1. Dust cup
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the igure. The size of bits which the dust cup can be
attached to is as follows.
3
► 1. Change lever 2. Lock button 3. Pointer
Dust cup 5
Dust cup 9
8
ENGLISH
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm
Chipping/Scaling/Demolition
OPERATION
CAUTION:
•
Always use the side grip (auxiliary handle) and
irmly hold the tool by both side grip and switch
handle during operations.
Hammer drilling operation
Set the change lever to the symbol.
Hold the tool irmly with both hands. Turn the tool on
and apply slight pressure on the tool so that the tool will
not bounce around, uncontrolled. Pressing very hard on
the tool will not increase the eficiency.
Drilling in wood or metal
Set the change lever to the symbol.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
1
2
CAUTION:
•
When the bit begins to break through concrete
or if the bit strikes reinforcing rods embedded
in concrete, the tool may react dangerously.
Maintain good balance and safe footing while
holding the tool irmly with both hands to prevent
dangerous reaction.
► 1. Chuck adapter 2. Keyless drill chuck
1
Blow-out bulb (optional accessory)
3
2
1
► 1. Spindle 2. Quick change drill chuck 3. Change
cover
► 1. Blow-out bulb
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
9
ENGLISH
MAINTENANCE
1
CAUTION:
•
2
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
Lubrication
► 1. Sleeve 2. Ring
CAUTION:
•
For Model HR3200C,HR3210C
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page.
Set the change lever so that the pointer points to
the symbol.
For Model HR3210FCT
Use the quick change drill chuck as standard equipment. When installing it, refer to "changing the quick
change chuck for SDS-plus " described on the previous
page.
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring irmly and turn the sleeve clockwise to tighten the chuck. To remove the bit, hold the
ring and turn the sleeve counterclockwise.
Set the change lever to the
symbol.
You can drill up to 13 mm diameter in metal and up to
32 mm diameter in wood.
•
•
•
Never use "rotation with hammering" when the
quick change drill chuck is installed on the tool.
The quick change drill chuck may be damaged.
Pressing excessively on the tool will not speed
up the drilling. In fact, this excessive pressure
will only serve to damage the tip of your bit,
decrease the tool performance and shorten the
service life of the tool.
There is a tremendous twisting force exerted
on the tool/bit at the time of hole breakthrough.
Hold the tool irmly and exert care when the bit
begins to break through the workpiece.
Always secure small workpieces in a vise or
similar hold-down device.
Diamond core drilling
When performing diamond core drilling operations,
always set the change lever to the
position to use
"rotation only" action.
CAUTION:
•
This tool requires no hourly or daily lubrication because it has
a grease-packed lubrication system. It should be relubricated
regularly. Send the complete tool to Makita Authorized or
Factory Service Center for this lubrication service.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended for use with your Makita tool speciied in this
manual. The use of any other accessories or attachments might present a risk of injury to persons. Only
use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
SDS-Plus Carbide-tipped bits
•
Bull point
•
Core bit
•
Cold chisel
•
Diamond core bit
•
Hammer grease
•
Scaling chisel
•
Grooving chisel
•
Drill chuck assembly
•
Drill chuck S13
•
Chuck adapter
•
Chuck key S13
•
Bit grease
•
Side grip
•
Depth gauge
•
Blow-out bulb
•
Dust cup
•
Safety goggles
•
Plastic carrying case
CAUTION:
•
This servicing should be performed by Makita
Authorized Service Centers only.
If performing diamond core drilling operations
using "rotation with hammering" action, the
diamond core bit may be damaged.
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
10
ENGLISH
11
M a kit a C o r p o r a tio n
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
884769C228
EN
20170203