Signal Analysis Measurement Fundamentals: Optimize Noise Floor

Keysight Technologies
Signal Analysis Measurement Fundamentals
Optimize Noise Floor, Resolution Bandwidth, and More
Application Note
For an RF engineer, a spectrum analyzer or signal analyzer is an essential and fundamental measurement
tool, used in all phases of the product life cycle. Key characteristics such as performance, accuracy and
speed help R&D engineers enhance their designs and help manufacturing engineers improve test efficiency
and product quality. This note offers a variety of techniques that will help you master signal analysis in your
application. Our focus is on helping you optimize attributes such as measurement noise floor, resolution
bandwidth, dynamic range, sensitivity, and more, while maintaining speed and productivity.
We generally use the term “signal analyzer” to indicate an instrument that has a spectrum analyzer
architecture and an all-digital intermediate frequency (IF) section that processes signals as complex vector
quantities, enabling multi-domain operations such as digital modulation analysis and time capture. A
broader discussion of spectrum and signal analyzers and their operation is available in Keysight Application
Note 150, Spectrum Analysis Basics.
03 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Improve Measurement Accuracy in Each Test Setup
To optimize measurement accuracy, it’s important to understand the signal analyzer’s
inherent accuracy and identify the sources of error in the connection of the device under
test (DUT). A combination of good measurement practices and useful analyzer features
will mitigate errors and may shorten test time.
Digital IF technologies yield a high level of basic accuracy, especially when enhanced
with internal calibrations and alignments. For example, self-generated corrections
and highly repeatable digital filters give you the freedom to change settings during a
measurement with little impact on repeatability. Typical examples include resolution
bandwidth, range, reference level, center frequency, and span.
Once the DUT is connected to a calibrated analyzer, the signal-delivery network (Figure
1) may degrade or alter the signal of interest. Correcting or compensating for these
effects will ensure the best accuracy. You can do this—conveniently and effectively—
using the analyzer’s built-in amplitude correction function in conjunction with a signal
source and a power meter.
Spectrum analyzer
Signal-delivery network
- Cables
- Adapters
- Noise
Shift reference plane
Figure 1. The quality of the DUT/analyzer connection can have a significant effect on measurement accuracy and
repeatability. This effect grows as frequencies increase.
04 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Figure 2 depicts the measured frequency response of a signal-delivery network that
attenuates the DUT’s signal. Removing the unwanted effects starts with measuring the
frequency response of the signal-delivery network over the desired frequency span. In
the analyzer, the amplitude correction feature uses a list of frequency/ amplitude pairs
and linearly connects them to produce correction factors corresponding to the measured
display points. It then adjusts the displayed magnitude according to those corrections.
In Figure 3, the unwanted attenuation and gain of the signal-delivery network have been
eliminated from the measurement, providing the fully specified accuracy of the signal
Figure 2. This trace shows the measured frequency response of the DUT/analyzer connection.
Figure 3. Applying the analyzer’s amplitude-correction feature flattens the frequency response, improving
amplitude accuracy.
05 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
This process shifts the measurement reference plane from the analyzer front panel to the
DUT. In many signal analyzers, you can store multiple different corrections for different
equipment configurations or analyzer setups.
You can also save correction values for different combinations of cables and adapters.
It’s always worthwhile to pay careful attention to the elements of the DUT/analyzer
connection, including the length, type and quality of cables and connectors. Connector
care, including proper torque, helps ensure minimum loss, good impedance match, and
repeatability—especially at microwave and millimeter-wave frequencies.
In challenging measurements, you may be able to improve performance by moving the
analyzer’s effective input nearer to the DUT. For example, when measuring very small
signals, you can connect external preamps directly to the DUT, increasing signal levels
and mitigating problems such as attenuated signals or added noise. Today’s smart
preamps automatically configure the analyzer and upload gain and frequency response,
enabling precise corrections.
Similarly, smart mixers can enhance measurements at very high frequencies. You can
place these at the DUT output, which is often a direct waveguide connection. The mixer
automatically identifies itself and downloads its conversion factors for accurate display
of results.
06 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Balance the Tradeoffs when Setting Resolution
The resolution bandwidth setting is a fundamental analysis parameter. It’s especially
important when the goal is to separate crucial spectral components and set the noise
floor such that you can more easily distinguish signals of interest from noise contributed
by the analyzer or DUT.
When performing demanding measurements, spectrum analyzers must be accurate
and have an adequate combination of measurement speed and high dynamic range. In
most cases, emphasis on one adversely affects the other. One key tradeoff is the use of a
narrow or wide resolution bandwidth.
A narrow setting is advantageous when measuring low-level signals: it lowers the
displayed average noise level (DANL) of the spectrum analyzer, increasing the dynamic
range and improving measurement sensitivity. In Figure 4, an apparent –103 dBm signal
is more properly measured by changing the resolution bandwidth from 100 kHz to 10
kHz: the 10x reduction in resolution bandwidth improves DANL by 10 dB.
Figure 4. Reducing resolution bandwidth from 100 kHz to 10 kHz improves DANL and makes it easier to see the
signal of interest.
Of course, a narrow setting is not always ideal. For modulated signals, it is important
to set the resolution bandwidth wide enough to include the sidebands. Doing otherwise
will produce inaccurate power measurements unless an integrated band power
measurement is made (e.g., combining multiple measurement points to cover the entire
signal bandwidth). Such a measurement—integrating power from many points measured
with a narrow resolution bandwidth—is often the most practical technique for wideband
digitally modulated signals that are closely spaced.
07 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Narrower settings have an important drawback: slower sweep speeds. Sweep rates are
generally proportional to the square of the resolution bandwidth, so a wider setting
produces a much faster sweep across a given span compared to a narrower setting.
Figures 5 and 6 compare the sweep times when using 10 kHz and 3 kHz resolution
bandwidths to measure a 200 MHz span.
Figure 5. A measurement with 10 kHz resolution bandwidth has a sweep time of 2.41 s.
Figure 6. Reducing resolution bandwidth to 3 kHz yields a sweep time of 26.8 s, which is about 10x slower than
Knowing the fundamental tradeoffs in resolution bandwidth selection can help you
adjust settings to emphasize whichever measurement parameter is most important.
While unfavorable tradeoffs cannot always be avoided, today’s signal analyzers can help
you mitigate or even eliminate them.
08 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Today’s analyzers ensure accurate measurements—even when using narrow resolution
bandwidths—by utilizing digital signal processing such as fast Fourier transforms (FFTs)
and digital resolution bandwidth filtering with correction for sweep speed effects. “Fast
sweep” features, for example, can increase sweep rates by as much as 50x for narrow
settings. Signal analyzers can automatically implement these improvements as part of
their center/span/RBW autocoupling, and you can further refine the setup by manually
optimizing for specific priorities such as speed and accuracy.
Increase Sensitivity When Measuring Low-Level Signals
An analyzer’s self-generated noise limits its ability to measure low-level signals, and a
variety of settings affect the level of that noise. For example, Figure 7 shows how the
analyzer’s noise floor obscures a 50 MHz signal.
Figure 7. In the shown configuration, the analyzer’s noise obscures a small signal.
To measure this low-level signal, you can improve the analyzer’s sensitivity by combining
the following: minimizing input attenuation, narrowing the resolution bandwidth (RBW)
filter, and using a preamplifier. Similar to the earlier technique, these techniques lower
DANL, separate small signals from noise, and enable accurate measurements.
Reducing input attenuation increases the level of the incoming signal at the analyzer’s
input mixer. Because the analyzer’s own noise is generated after the attenuator, the
attenuation setting affects the signal-to-noise ratio (SNR) of the measurement. If gain
in the analyzer is coupled to the input attenuator to compensate for changes, real
signals remain stationary on the display. However, DANL changes with IF gain, reflecting
the change in SNR that results from any change in the attenuator setting. Therefore,
minimizing input attenuation is essential to improving DANL.
After passing through the mixer and any internal amplification, the re-amplified signal
then enters the IF section that contains the resolution bandwidth filter. By narrowing the
filter width, less noise energy reaches the analyzer’s envelope detector and this lowers
the DANL of the measurement.
09 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Figure 8 shows successive reductions in DANL (note the reduction in reference level).
The top trace shows the CW signal above the noise floor after minimizing resolution
bandwidth. The middle trace shows the improvement after minimizing attenuation.
The lower trace employs logarithmic power averaging (using log-scaled dB readings),
reducing the noise floor another 2.5 dB without affecting the measurement of CW
signals. When combined with peak detection (the display detector setting), this is a
useful way to measure spurious signals near the noise floor (a common signal analysis
Figure 8. In these signal measurements, DANL becomes progressively lower after reducing resolution bandwidth
(yellow), reducing input attenuation (blue), and switching to log power averaging (purple).
Achieving maximum sensitivity requires use of a preamplifier with low noise and high
gain. If the amplifier gain is sufficiently high (e.g., displayed noise increases by at least
10 dB), then the noise figure of the amplifier dominates the combined noise floor of
preamplifier plus analyzer.
Subtracting the analyzer’s noise-power contribution from a specific measurement is
an effective way to reduce noise in spectrum measurements. While you could do this
by measuring the noise floor for each measurement, some Keysight X-Series signal
analyzers offer a more practical method called noise floor extension (NFE). With NFE,
the analyzer accurately models and characterizes noise power at each measurement
point, and it automatically subtracts these from the measurement. This can reduce the
effective noise floor by10 dB or more without changing sweep times. This technique can
be used in addition to the steps described above.
As mentioned earlier, the combination of log power averaging and peak detection
provides a 2.5 dB SNR benefit when measuring spurious signals near noise. Alternatively,
if the priority is maximum reduction of measurement variance in the noise floor (e.g., a
smoother trace) then power averaging using the “average” display detector may be the
best choice. The combination of the average detector and a slower sweep time is the
most efficient way to reduce variance due to noise (e.g., smooth the noise floor).
10 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
A technique called synchronous or time averaging is worth considering for the special
case of time-varying signals that repeat consistently. This feature is available in vector
signal analyzers and involves averaging samples of the input signal in the time domain
before calculating a frequency spectrum. A trigger is used to synchronize the timedomain samples to the repeating signal. The net effect is a substantial reduction in the
effective noise floor for measurements in the time, frequency, and modulation domains.
Optimize Dynamic Range when Measuring Distortion
A fundamental factor in spectrum analysis is the ability of an instrument to distinguish a
signal’s large fundamental tone from its smaller distortion products. This is the analyzer’s
dynamic range, specified as the maximum difference between signal and distortion,
signal and noise, or signal and phase noise.
When measuring the combination of a signal and distortion, the level at the input mixer
dictates the dynamic range. The mixer level used to optimize dynamic range can be
determined from three specifications: second-harmonic distortion (SHD), third-order
intermodulation (TOI) distortion, and DANL. Incorporating all three of these in a single
graph creates a plot of mixer level versus internally generated distortion and noise.
11 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Figure 9 plots the –75 dBc SHD point at a mixer level of –40 dBm, the –85 dBc TOI point
at a mixer level of –30 dBm, and a noise floor of –110 dBm corresponding to a 10 kHz
resolution bandwidth. The SHD line is drawn with a slope of 1 because SHD increases
by 2 dB for each 1 dB increase in the level of the fundamental at the mixer. However,
because distortion is determined by the difference between fundamental and distortion
product, the change is only 1 dB. Similarly, TOI is drawn with a slope of 2: for every 1
dB change in mixer level, third-order products change 3 dB, or 2 dB in a relative sense.
The maximum second- and third-order dynamic range can be achieved by setting the
attenuator so that the signal level at the mixer corresponds to the point where the
second- and third-order distortions are equal to the noise floor (annotation in the graph
identifies these mixer levels). Note that the minimum point is on a small curve resulting
from the addition of distortion and noise on the log (dB) scale.
Maximum second-order
dynamic range
Maximum third-order
dynamic range
mixer levels
Mixer level (dBm)
Figure 9. Second- and third-order dynamic range are shown as determined by minimum distortion regions at the
intersection of DANL and the corresponding distortion curves.
12 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
To increase dynamic range, a narrower resolution bandwidth must be used. As shown in
Figure 10, dynamic range increases when the RBW setting is decreased from 10 kHz to 1
kHz. Note that the increase is 5 dB for second-order and more than 6 dB for third-order
–60 Noi
dynamic range improvement
dynamic range improvement
Mixer level (dBm)
Figure 10. Reducing RBW lowers the analyzer’s DANL (lines starting at lower left) and improves the
operating point for both second- and third-order dynamic range.
As a final point, the analyzer’s phase noise can also affect dynamic range for intermodulation distortion (IMD). Reason: the frequency spacing between the various spectral
components (e.g., test tones and distortion products) is equal to the spacing between the
intermodulation test tones. For example, test tones separated by 10 kHz and measured
using a 1 kHz resolution bandwidth will result in the noise curve shown in Figure 11. If the
analyzer phase noise at a 10 kHz offset is only –80 dBc, then 80 dB will be the maximum
dynamic range for this measurement, not the 88 dB suggested by the intersection of
DANL and third-order distortion.
Phase noise
(10 kHz offset)
Dynamic range
reduction due
to phase noise
Mixer level (dBm)
Figure 11. For closely spaced signals such as intermodulation test tones, phase noise may limit the measurement
dynamic range to a value less than that the chart would suggest.
13 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Accurately Isolate and Measure Bursts and Transients
It’s difficult to accurately measurement bursted or pulsed signals, especially those that
carry modulation, when using a swept spectrum analyzer. The analyzer will display a
combination of the information carried by the pulse plus the frequency content of the
shape of the pulse (e.g., pulse envelope). Sharp rise and fall times will produce unwanted
frequency components in the spectrum. These unwanted artifacts can obscure the signal
of interest and reduce measurement accuracy.
Two measurement techniques address these problems: time-gated spectrum analysis
and triggered FFT analysis with a vector signal analyzer (VSA). Both are available in
signal analyzers such as the Keysight X-Series.
In swept analysis, the most flexible (and frequently used) technique is gated sweep or
gated LO. In this method, the analyzer is configured to sweep and take data only during
the desired portion of the input signal. An external trigger may be used to synchronize
measurements; however, some analyzers can generate triggers from the pulses themselves. It’s important to note that this type of time-selective spectrum analysis requires
a signal that repeats consistently. By accumulating successive measurements, the
analyzer builds up a complete spectrum result that provides stable and accurate results.
Generally, the intended effect is to measure the spectrum of the signal during the pulse
or burst itself and reject the spectral effects of the pulse switching on or off. This allows
the use of gating with automated power-measurement functions such as channel power
or adjacent-channel power (ACP) and spectrum emissions mask (SEM).
The other technique involves FFT processing of the signal and is sometimes called gated
FFT. This method does not require a repeating signal; however, if the signal does repeat,
SNR may benefit from time averaging (as described previously).
Gated FFT analysis is most powerful and flexible when performed with a signal analyzer
and VSA software. The software performs triggering functions such as precisely
adjusting trigger timing plus gate or FFT time-record length to match the bursts of the
signal under test.
The VSA software also allows wide adjustment of the number of FFT points and selection
of the applied window shape (i.e., weighting). Window shapes carry inherent tradeoffs
between amplitude accuracy, frequency resolution and dynamic range in the resulting
measurements. Optimizing these tradeoffs helps you extract the maximum amount of
information from brief signal bursts.
One especially effective approach for time-selective signal analysis applies to signals
that are self-windowing—that is, those that are periodic in a specific time interval.
Examples include the orthogonal frequency-division multiplexing (OFDM) signals
commonly used in wireless systems. For these, the time-record length or gate length
can be set to match a single OFDM symbol or an integer number of symbols, and a
uniform window is then selected. This window is flat in the time domain, and it relies on
the match between the periodicity of the signal under test and the window or FFT time
14 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Figure 12 compares the flat-top window, designed for amplitude accuracy (i.e., flat in the
frequency domain), to the uniform window when measuring two symbols of an OFDM
training sequence. In this situation, the uniform window provides high accuracy and
optimum frequency resolution.
Figure 12. Both traces show an off-air capture of an OFDM WLAN waveform in the 5 GHz band. In each
measurement, the gate is aligned with a portion of the self-windowing training sequence. In the lower trace,
the uniform window provides sufficient resolution to reveal individual OFDM subcarriers.
Enhance Speed, Accuracy, Reliability with
Measurement Applications
The increasing complexity of signals in wireless and aerospace/defense applications
has made it more difficult—and sometimes impractical—to manually configure some
spectrum and modulation-quality measurements. Fortunately, the processing
capabilities in today’s signal analyzer make it easier to set up not only complex
measurements but also traditional measurements such as spurious, harmonics, and
phase noise.
The most convenient way to combine processing power with measurement intelligence
is through measurement application software (“measurement applications”) installed
and resident in the signal analyzer. These applications can be divided into two broad
categories: general-purpose and standard-specific.
General-purpose applications are focused on traditional analysis tasks, extending
into areas where instrument-hosted automation can handle a range of common
requirements. These applications are helpful in the development and manufacturing of
RF and microwave transceivers and their components. In the Keysight X-Series signal
analyzers, PowerSuite is a standard feature. This comprehensive set of measurements
includes channel power, ACP, occupied bandwidth, complementary cumulative
distribution function (CCDF), harmonic distortion, spurious emissions, TOI, and SEM.
15 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Other general-purpose applications address phase noise, noise figure, electromagnetic
compatibility (EMC), and comprehensive pulse analysis (Figures 13 and 14, respectively).
In all cases, the measurement applications dramatically ease measurement set-up
(reducing tedium and errors) and provide customized displays that summarize large
numbers of measurement results to simplify interpretation or provide pass/fail
indications (Figures 13 and 14).
Figure 13. The N6141C EMC application configures measurements is compliant with CISPR 16-1-1 or MIL-STD
requirements when performing pre-compliance measurements of conducted and radiated emissions.
Figure 14. The N9067C pulse measurement application gathers information from large numbers of pulses and
calculates parameters such as period, width, pulse repetition interval (PRI), rise/fall time, overshoot, average
power, and peak power.
16 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Dozens of standard-specific applications are available for signal analyzers, mainly for
established and emerging wireless standards such as LTE/LTE-Advanced, GSM, W-CDMA,
WLAN, Bluetooth, and digital video. These transform a basic RF tool—the signal analyzer—
into a standards-based transmitter tester, providing RF conformance tests and informative
displays for evaluation and troubleshooting. In some cases an application is the only
practical way to configure the analysis of complex, highly-specific wireless standards.
Figures 15 and 16 show LTE-based examples of typical measurements from the
N9080/9082C measurement application. These displays include both graphical and
tabular measurement data, and can be configured for pass/fail testing.
Figure 15. This display of an LTE downlink demodulation result includes the constellations of different signal
layers (top) and detected resource allocations (bottom right).
Channel power measurements of advanced digital-modulation schemes can be complex
to manually configure and tedious to interpret. For example, the LTE-Advanced standard
includes a cumulative ACLR (CACLR) measurement for signals configured for noncontiguous carrier aggregation.
17 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Identify Internal Distortion Products
When high-level signals reach the spectrum analyzer input, they may cause distortion
products that mask the real distortion on the input signal. Using dual traces and the
analyzer’s RF attenuator, you can determine whether or not distortion generated within
the analyzer is affecting the measurement.
This is a useful measurement, as it allows you to optimize the critical attenuation setting
for your specific setup—signal, analyzer, and connection. This individualized optimization
is often better than what you might calculate from guaranteed instrument specifications.
To start, set the analyzer’s input attenuator so that the input signal level minus the
attenuator setting is about 0 dBm. To identify these products, tune to the second
harmonic of the input signal and set the input attenuator to 0 dBm. Next, save the screen
data in Trace B, select Trace A as the active trace, and activate Marker ∆. The spectrum
analyzer now shows the stored data in Trace B and the measured data in Trace A, while
Marker ∆ shows the amplitude and frequency difference between the two traces. Finally,
increase the RF attenuation by ~15 dB and compare the response in Trace A to the
response in Trace B.
18 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Figure 16. Because the signal analyzer accounts for input attenuation and reference level, a difference in the
apparent second-harmonic amplitude is due to distortion from the analyzer.
If the responses in Trace A and Trace B differ, as in Figure 16, then the analyzer’s mixer
is generating internal distortion products due to the high level of the input signal. In this
case, more attenuation is required, leading to the result in Figure 17. In some analyzers
you can experiment with attenuation values in steps as small as 1 dB.
Figure 17. The second-harmonic measurements appear at the same amplitude, indicating that the analyzer’s
own distortion is not causing an error in the result.
19 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Find and Measure Elusive Signals using Real-Time
Whether you work in wireless or aerospace/defense, many signals are pulsed or bursted,
or they otherwise exhibit complex transient behavior that must be characterized. In some
cases, undesirable signals or behaviors are obscured and therefore difficult to detect or
isolate. Understanding these signals or behaviors may be essential to troubleshooting or
optimizing a system.
The digitizing architecture and high-speed DSP used in many signal analyzers addresses
these needs in two ways: real-time spectrum analyzers and signal recording/playback
in vector signal analyzers. Previously, both of these capabilities were implemented
as separate, dedicated products. Today, both available as optional capabilities for
mainstream signal analyzers such as the Keysight X-Series.
Real-time spectrum analyzers (RTSAs) use specialized processing in the IF section to
calculate spectrum results from the continuous stream of sampled data representing the
IF input. They perform these spectrum calculations with sufficient speed that all signal
samples are processed, producing gap-free spectrum results. No signals or behaviors
are missed.
Because RTSA can generate spectra at very high rate—many thousands per second—the
human eye cannot see or interpret individual spectra. Instead, spectra are presented
in displays that typically use color to indicate how often specific amplitude/frequency
combinations occur in the results. The color and shading of these spectral density
displays can be adjusted to show or highlight very frequent—or, more often, very
infrequent—events (Figure 18).
Figure 18. These off-air spectrum density measurements of the 2.4 GHz ISM band include brief Bluetooth hops
and longer WLAN transmissions. Amplitude and frequency values that occur more often are shown in red and
yellow, while less-frequent values are shown in blue (e.g., Bluetooth hops).
20 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
The real-time spectral-density displays are useful when chasing intermittent signals
or behaviors, and the measurements behind them can be used to generate triggers
for isolating specific signals or behaviors. A frequency mask can be manually or automatically generated, and signals that violate a mask result in a trigger event (Figure 19).
Figure 19. In the RTSA option, the frequency mask trigger is shown by the dark green shading above the
spectrum, and level/frequency combinations are defined by the circles. Signal hops that occur outside the mask
generate a trigger.
21 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
When pursuing elusive signals or behaviors, the most powerful analysis technique is the
combination of frequency mask triggering and the signal capture/playback capability
of VSAs. While the RTSA measurements resulting from the frequency mask trigger are
power spectrum only, the VSA signal capture or time capture records the complete time
record of the signal, a vector quantity. By post-processing this complete recording,
the VSA can perform multiple types of analysis, including spectrum, time domain, and
demodulation (Figure 20).
Figure 20. This vector signal analyzer display shows a frequency mask trigger initiating the capture and
subsequent demodulation of a single frequency hop.
To reveal more information about signal behavior, captures initiated by a frequency mask
trigger can be adjusted to begin after or before the trigger event. This flexible timing can
be very useful in troubleshooting when looking for a cause that precedes a specific signal
behavior, or when cause and behavior are separated in time.
Engineering is all about connecting ideas and solving problems. This experience drives
the X-Series signal analyzers. They’re the benchmark for accessible performance
that puts you closer to the answer by easily linking cause and effect. Across the full
spectrum—from CXA to UXA—you’ll find the tools you need to design, test and deliver
your next breakthrough. Reach for the X-Series and make an inspired connection.
To learn more, read Spectrum Analysis Basics or visit
22 | Keysight | Signal Analysis Measurement Fundamentals: Optimize Noise Floor, Resolution Bandwidth, and More - Application Note
Evolving Since 1939
Our unique combination of hardware, software, services, and people can help you
reach your next breakthrough. We are unlocking the future of technology.
From Hewlett-Packard to Agilent to Keysight.
A personalized view into the information most relevant to you.
Register your products to get up-to-date product information and
find warranty information.
Keysight Services
Keysight Services can help from acquisition to renewal across your
instrument’s lifecycle. Our comprehensive service offerings—onestop calibration, repair, asset management, technology refresh,
consulting, training and more—helps you improve product quality
and lower costs.
Keysight Assurance Plans
Up to ten years of protection and no budgetary surprises to ensure
your instruments are operating to specification, so you can rely on
accurate measurements.
Keysight Channel Partners
Get the best of both worlds: Keysight’s measurement expertise and
product breadth, combined with channel partner convenience.
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Pacific
Hong Kong
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 11 2626
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
United Kingdom
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
For other unlisted countries:
DEKRA Certified
ISO9001 Quality Management System
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2015
Quality Management System
This information is subject to change without notice.
© Keysight Technologies, 2016 - 2017
Published in USA, December 13, 2017