Safety CE We declare, under our sole responsibility, that

Dimensions
VEXU cameras – Integrating essential basic functionalities
2 x M3 x 4
30
8 x M3 x 4
20
22
▪▪ up to 2.3 Megapixel
▪▪ up to 217 fps
▪▪ 29 × 29 mm housing with all-sided M3 mount
▪▪ Global shutter architecture for minimized motion blur
▪▪ Integrating essential basic functionalities
▪▪ USB bus powered
▪▪ USB VisionTM standard compliant
3
8,4
Notice
Further technical details are available in the respective data sheets.
37,8
ø 28,7
Product Specification
CS-mount
1,55 ±0,35
6,15
6
20
29
8,2
29
Quick Start Guide
VEXU cameras (USB 3.0)
18
3
20
Latest software version and technical
documentation available at:
vt.baumer.com
System Requirements
Safety
Safety Precautions
Notice
Conformity:
CE, RoHS
See the User's Guide for the
complete safety instructions!
CPU
Caution
Observe precautions for
handling electrostatically
sensitive devices!
CE
We declare, under our sole responsibility, that
the previously described Baumer VEXU cameras conform with the directives of the CE.
▪▪ Protect the sensor from dirt and
moisture.
▪▪ Do not allow the camera to become
contaminated with foreign objects.
Environmental Requirements
RoHS
All VEXU cameras comply with the recommendation of the European Union concerning
RoHS Rules.
Storage temp.
Operating temp.
Humidity
-10 ° C ... +70 °C
see Heat Transmission
10 % ... 90 %
Non-condensing
Further Information
For further information about our products, please visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com · Phone +49 (0)3528 4386-845 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter is not guaranteed.
The information in this document is subject to change without notice.
Printed in Germany 09/17.
v1.1
1164079
RAM
Installation
Single-camera system
Multi-camera system
Recommended
Recommended
Intel® Core™ i5-2520M
Intel® Core™ i7-3770
CPU @ 2.50 GHz, Cores: 4
CPU @ 3.40 GHz, Cores: 8
4 GB
8 GB
Operating
Microsoft® Windows® 7 32 / 64 bit systems (required for USB 3.0)
system
Microsoft® Windows® 8 32 / 64 bit systems (required for USB 3.0)
(OS)
Microsoft® Windows® 10 32 / 64 bit systems (required for USB 3.0)
Lens Mount
Notice
Ensure the sensor and lens are not contaminated with dust and airborne
particles when mounting the support or the lens to the device!
The following points are very important:
▪▪ Install the camera in an environment that is as dust free as possible!
▪▪ Keep the dust cover (bag) on the camera for as long as possible!
▪▪ Hold the camera with the sensor downwards if the sensor is uncovered.
▪▪ Avoid contact with any of the camera‘s optical surfaces!
General Description
Heat Transmission
LED signals
Caution
1
Heat can damage the camera. Heat must be dissipated adequately
to ensure that the temperature does not exceed the values in the
table below.
As there are numerous possibilities for installation, Baumer recommends no specific method for proper heat dissipation, but suggest
the following principles:
2
▪▪ operate the cameras only in mounted condition
▪▪ mounting in combination with forced convection may provide
proper heat dissipation
LED
T
4
No.
Description
3
No.
1
Lens mount (CS-mount)
2
Digital IO
3
USB 3.0 port
Description
4
LED
Signal
Meaning
green flash
Power on
green
USB 3.0 connection
red
USB 2.0 connection
yellow
Readout active
red flash
Update
LED
Data Interface / Digital IOs
Installation
VBUS
6
MicB_SSTX-
2
D-
7
MicB_SSTX+
3
D+
8
GND_DRAIN
4
ID
9
MicB_SSRX-
5
GND
10
MicB_SSRX+
1. Check camera operation using the LED signals.
2. Check connection using Windows Device Manager:
open wire
→ If device is not listed:
• Check the host controller power supply.
• Check USB 3.0 cable and connection.
→ If device is regularly not listed
• Check USB 3.0 driver installation.
2
4
3
brown
white
Troubleshooting
→ If LED is red:
• Camera is connected to USB 2.0 (settings possible).
Digital IOs (on camera side)
wire colors of the connecting cable (ordered separately)
VCC (Out)
IN+
65°C (149°F)
▪▪ Connect the camera to the USB connection on your PC using an appropriate
cable.
▪▪ If required, connect a trigger and / or flash to the digital IOs.
1
2
Maximum Temperature
6 7 8 9 10
1
1
Measurement Point (T)
Installing the camera:
USB 3.0 (Micro B)
1 23 45
Measurement Point
3
4
GND (IN)
OUT
blue
black
Installation example
1 - PCI USB board
2 - USB cable
3 - Cable for trigger and flash
Download PDF