Cot Bed
The help of an assistant will aid assembly
Side Panel x 2
End Panel x 2
Base x 1
Bolt x 16
Barrel Nut x 16
Hexagon Key x 1
You will need a flat-bladed screwdriver to assemble this product.
Keep children clear during assembly as pack contains small parts
which may present a choking hazard.
Cot Assembly 1. Fitting the Base.
End Panel
Bolt x 2 (4 in top position)
Barrel Nut x 2 (4 in top position)
1. Choose one of the three positions for the base.
If using the high position, insert four bolts into
the upper set of bolt holes. If using the lower
two positions, use only two bolts.
The lowest position is the safest and should
always be used in that position as soon as the
baby is old enough to sit up.
2. If using the top base position, insert the Barrel
nuts into all four holes on the inner faces of
the base rails. (For other positions use UPPER
HOLES ONLY) with the screwdriver slot showing
and ensure that it is aligned with the holes in
the end of the Base side rail.
3. Do not fully tighten bolts at this stage.
4. Retain any unused fittings for future use.
Cot Assembly 2. Attaching the Side Panels.
Side Panel
Bolt x 2
End Panel
Repeat with second Side Panel
Do not fully tighten bolts at this stage.
Barrel Nut x 2
Cot Assembly 3. Attaching the second End Panel.
Barrel Nut x 4
Bolt x 4
Barrel Nut x 2
Fully tighten all bolts once
assembly is complete.
Bolt x 2
Bed Assembly.
Bolt x 4
End Panel
End Panel
Bolt x 4
Barrel Nut x 4
Barrel Nut x 4
Fully tighten all bolts once
assembly is complete.
In Use
The base can be adjusted in height in cot mode, but the lowest position is the safest and should always
be used in that position as soon as the baby is old enough to sit up.
This product is suitable for a mattress of 1400mm in length and 700mm in width. When used in cot
mode, the maximum thickness of the mattress is 100mm.
The length and width of the mattress shall be no less to ensure the gap between the mattress and the
sides and ends does not exceed 30mm.
The thickness of the mattress shall be such that the internal height (surface of the mattress to the upper
edge of the cot frame) is at least 500mm in the lowest position of the cot base and at least 200mm in
the highest position of the cot base.
To prevent injury from falls the cot should no longer be used for the child once they are able to climb
out of the cot.
The bed mode is suitable for a child from 18 months to 4 years old.
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be
placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords. It
should be placed either tight to any wall or have a gap of 300mm between the wall and the side of the
Care and Maintenance
All assembly fittings should be tightened properly and should be checked regularly and
re-tightened as necessary.
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.
An occasional light application of a wax polish will help maintain a good appearance.
This product complies with BS EN 716 - 1: 2008 + A1: 2013 and BS 8509: 2008 + A1: 2011
Warning: Do not use the cot or bed if any part is broken, torn or missing and use only spare parts
approved by the manufacturer.
Warning: Do not leave anything in the cot or place the cot close to another product, which could provide
a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
Warning: Do not use more than one mattress in the cot.
Warning: Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires,
gas fires, etc. near the vicinity of the cot.
Warning: Do not place the child’s bed near heat sources, windows and other furniture.
This product can be carefully dismantled for storage and transportation.
Customer Care line for this product 01692 408802
East Coast Nursery Ltd. Robertson House, North Walsham, Norfolk, NR28 0BX