HPE Integrity Superdome X

QuickSpecs
HPE Integrity Superdome X
Overview
HPE Integrity Superdome X
HPE Superdome X
Page 1
QuickSpecs
HPE Integrity Superdome X
Overview
HPE BladeSystem Superdome Enclosure front
HPE BladeSystem Superdome Enclosure back
HPE BL920s Gen9 Server Blade
Page 2
QuickSpecs
HPE Integrity Superdome X
Overview
HPE Superdome X: The Ultimate x86 based Mission-critical Platform
HPE Superdome X is an HPE server that represents a new category of x86 modular, mission-critical systems to consolidate all tiers
of critical applications on a common platform. Engineered with trusted Superdome 2 reliability, the HPE Superdome X includes a
modular, bladed design, and shares HPE BladeSystem efficiencies including a common server management framework, supported
from x86 to Superdome 2. With breakthrough innovations such as the fault-tolerant Crossbar Fabric and Error Analysis Engine
coupled with hard partitioning capabilities, Superdome X sets the standard for mission-critical x86 computing.
Key features and
benefits
HPE Superdome X offers scalability that surpasses the market, flexibility through HPE nPARs, and mission
critical RAS functionality. In summary:
• Support for up to 16 Intel® Xeon® Processor E7 v4 and E7 v3 Family
• 384 DIMM slots with up to 48 TB of DDR4 memory (Gen9), providing a large memory footprint for
the most demanding applications
• 16 FlexLOM slots (2 per blade) providing LAN on motherboard configuration flexibility
• 24 Mezz PCIe gen3 slots (3 per blade) for maximum IO bandwidth connectivity to LAN, SAN, and
InfiniBand
• Built-in shared DVD
• HPE nPARs: 1-, 2-, 3-(BL920s Gen9 blades only), 4-, 6-(BL920s Gen9 (v4) blades only) or 8-Blade
and multiple nPARs supported for greater system reliability and licensing optimization
• Error Analysis Engine self-heals by driving response to failures, minimizing human error
General
The HPE BladeSystem Superdome Enclosure is the foundational building block for Superdome X. Each
compute enclosure supports 15 fans, 12 power supplies, associated power cords, 2 Onboard Administrator
(OA) modules, 2 Global Partitioning Services Modules (GPSM), and four HPE Crossbar Fabric Modules
(XFMs). Configurations of 1 to 8 blades can be populated in an enclosure with support for hard partitions
(nPars) containing 1, 2, 3*, 4, 6** or 8 Blades. Multiple HPE nPars of different sizes are supported within a
single enclosure.
NOTE*: BL920s Gen9 blades only
NOTE**: BL920s Gen9 (v4) blades only
HPE BladeSystem
Superdome
Enclosure
The enclosure can support up to eight server blades and up to eight IO Interconnect Modules.
BL920s Server
Blade
Each server blade – has the following specifications:
1. Includes two Intel E7 v4 or E7 v3 processors. The included processors depends on which blade
model is purchased.
2. 48 DIMMs slots for DDR4 memory (Gen9) or DDR3 memory (Gen8)
3. 3 Mezzanine slots (1 x8, 2 x16) PCIe gen3
4. 2 FlexLOM slots
5. The XNC2 chipset to enable smooth, high-performance scalability from 2 to 16 sockets in addition to
mission-critical class RAS features.
Partitioning
Packages
Each enclosure must be purchased with one of these two partitioning licenses:
1. Basic Partition License = Single Partition, up to 4 blades (8s) in size = “Entry” config
2. Advanced Partition License = Multiple partitions, each up to 8 blades (16s) in size.
Page 3
QuickSpecs
HPE Integrity Superdome X
Service and Support
HPE Care Pack, and Warranty Information
Warranty
Hewlett Packard Enterprise branded hardware and options qualified for the HPE Superdome X are covered
by a global limited warranty and supported by HPE Services and a worldwide network of Hewlett Packard
Enterprise Authorized Channel Partners. The Hewlett Packard Enterprise branded hardware and options
diagnostic support and repair is available for three years from date of purchase, or the warranty length of the
server they are attached to, whichever is greater. Additional support may be covered under the warranty or
available through additional support packages. Enhancements to warranty services are available through
HPE Pointnext operational services or customized service agreements.
Additional information regarding worldwide limited warranty and technical support is available at:
http://h20565.www2.hpe.com/hpsc/doc/public/display?docId=c01865770
Support Services
HPE Technology
Services for
Superdome X
HPE Technology Services delivers confidence, reduces risk and helps customers realize agility and stability.
Connect to Hewlett Packard Enterprise to help prevent problems and solve issues faster. Our support
technology lets you to tap into the knowledge of millions of devices and thousands of experts to stay
informed and in control, anywhere, any time.
HPE Pointnext operational services enable you to order the right service level, length of coverage and
Protect your
response time as you purchase your new server, giving you full entitlement for the term you select.
business beyond
warranty with HPE
Pointnext
operational services
Optimized Support HPE Proactive Care Advanced – Call to repair commitment, 24x7 coverage, three year Care Pack Service
Improve system availability and performance with personal attention from a locally assigned Account Support
recommendation
Manager while you increase stability and reduce unplanned downtime by connecting to Hewlett Packard
Enterprise for automated problem detection. This level of HPE Proactive Care Advanced combines rapid
critical event management with the industry’s highest level of hardware support commitment – hardware will
be returned to operating conditions within six (6) hours after you open your case. Collaborative software call
management is included; you may prefer full software support from Hewlett Packard Enterprise where we
own all cases through to resolution. As a leading global software support provider, we leverage the
knowledge and experience gained from long, successful relationships with leading Linux vendors. Purchasing
software support from Hewlett Packard Enterprise simplifies troubleshooting and shortens time to resolution
with one call for hardware or software questions.
Hewlett Packard Enterprise hardware Installation
This easy-to-buy, easy-to-use HPE Care Pack service helps ensure your new Hewlett Packard Enterprise
hardware is installed smoothly, efficiently and with minimal disruption to your IT and business operations.
Related Services
Data Center Platform Consulting Services
These services help modernize key systems and leverage new technology to support a changing business
climate and prepare you for the new style of IT. Hewlett Packard Enterprise understands the needs of the
data center of the future and will serve as your guide for the journey.
https://www.hpe.com/us/en/services/consulting.html
Data Privacy Services
Protect your data through better media management. HPE Data privacy services help manage and protect
sensitive data. http://www.hpe.com/services/dataprivacy
Factory Express for Servers and storage
Page 4
QuickSpecs
HPE Integrity Superdome X
Service and Support
HPE Factory Express offers configuration, customization, integration and deployment services for Hewlett
Packard Enterprise servers and storage products. Choose how your factory solutions are built, tested,
integrated, shipped and deployed. www.hpe.com/info/factoryexpress
Additional HPE Pointnext operational services can be found at: http://ssc.hpe.com/portal/site/ssc/
Parts and Materials Hewlett Packard Enterprise will provide HPE-supported replacement parts and materials necessary to
maintain the covered hardware product in operating condition, including parts and materials for available and
recommended engineering improvements.
Parts and components that have reached their maximum supported lifetime and/or the maximum usage
limitations as set forth in the manufacturer's operating manual, product quick-specs, or the technical product
data sheet will not be provided, repaired, or replaced as part of these services.
Insight
Online/Insight
Remote Support
Recommended
support services
The defective media retention service feature option applies only to Disk or eligible SSD/Flash Drives
replaced by Hewlett Packard Enterprise due to malfunction.
HPE Insight Remote Support provides 24 X 7 remote monitoring, proactive notifications, and problem
resolution. This comes at no additional cost with your HPE solution. Learn more about Insight Remote
Support and Insight Online.
Operating System Installation & Startup Service
HA114A1#5H4 – Linux
HA114A1#5FR - Windows
Boot from SAN Service
HA124A1#59J
Network Service
HA124A1#56H
SAN Deployment Service
HA124A1#5VY
Page 5
QuickSpecs
HPE Integrity Superdome X
Standard Features
HPE BL920s Gen9
Server Blade
HPE BL920s Gen8
Server Blade
w/Intel Xeon v4
Processors
Each server blade supports two (per blade) of these processors:
Intel® Xeon® Processors: E7-8894 v4 24-core/2.4GHz/165W/60MB
Intel® Xeon® Processors: E7-8893 v4 4-core/3.2GHz/140W/60MB
Intel® Xeon® Processors: E7-8891 v4 10-core/2.8GHz/165W/60M
Intel® Xeon® Processors: E7-8890 v4 24-core/2.2GHz/165W/60M
Intel® Xeon® Processors: E7-8880 v4 22-core/2.2GHz/150W/55M
Intel® Xeon® Processors: E7-8855 v4 14-core/2.1GHz/140W/35MB
w/Intel Xeon v3
Processors
Each server blade supports two (per blade) of these processors:
Intel® Xeon® Processor E7-8891 v3 10-core/2.8GHz/165W/45M
Intel® Xeon® Processor E7-4850 v3 14-core/2.2GHz/115W/35M
Intel® Xeon® Processor E7-8880 v3 18-core/2.3GHz/150W/45M
Intel® Xeon® Processor E7-8890 v3 18-core/2.5GHz/165W/45M
Intel® Xeon® Processor E7-8893 v3 4-core/3.2GHz/140W/45M
w/Intel Xeon v2
Processors
Each server blade supports two (per blade) of these processors:
Intel® Xeon® Processor E7-2890 v2 (15c/2.8Ghz / 37.5M / 155W)
Intel® Xeon® Processor E7-2880 v2 (15c/2.5Ghz / 37.5M / 130W)
Intel® Xeon® Processor E7-4830 v2 (10c/2.2Ghz / 20M / 105W)
Intel® Xeon® Processor E7-8891 v2 (10c/3.2Ghz / 37.5M / 155W)
Intel® Xeon® Processor E7-8893 v2 (6c/3.4Ghz / 37.5M / 155W)
Chipset
HPE sx3000 and XNC2
Upgradability and
scalability
Scalable from 2 socket configurations to 16 socket configurations
Memory type for
HPE BL920s Gen9
Server Blades
HPE 64GB (4x16GB) DDR4-2133 CAS-15-15-15 LRDIMM Memory Kit
HPE 128GB (4x32GB) DDR4-2133 CAS-15-15-15 LRDIMM Memory Kit
HPE 128GB (4x32GB) DDR4-2400 CAS-17 LRDIMM Memory Kit
HPE 256GB (4x64GB) DDR4-2400 CAS-17 LRDIMM Memory Kit
HPE 512GB (4x128GB) DDR4-2400 CAS-17 LRDIMM Memory Kit
Memory type for
HPE BL920s Gen8
Server Blades
HPE 64GB (4x16GB) PC3-12800R (DDR3-1600) Registered CAS-11 Memory Kit
HPE 128GB (4x32GB) PC3-14900R (DDR3-1866) Registered CAS-13 Memory Kit
Memory protection Error checking and correcting (ECC) on memory and caches; double-chip spare
Certified operating HPE BL920s Gen9 (v4) Server Blades
environments
• Red Hat Enterprise Linux (RHEL)
• SUSE Linux Enterprise Server (SLES)
• Microsoft Windows Server 2012 R2 Standard and Datacenter (including
Microsoft SQL Server 2014 and 2016)
• VMware vSphere 6.0 U2
HPE BL920s Gen9 (v3) Server Blades
• Red Hat Enterprise Linux (RHEL)
• SUSE Linux Enterprise Server (SLES)
• Microsoft Windows Server 2012 R2 Standard and Datacenter (including
Microsoft SQL Server 2014 and 2016)
• VMware vSphere 5.5 U3 and 6.0 U1
Page 6
QuickSpecs
HPE Integrity Superdome X
Standard Features
•
CentOS
HPE BL920s Gen8 Server Blades
• Red Hat Enterprise Linux (RHEL)
• SUSE Linux Enterprise Server (SLES)
• Microsoft Windows Server 2012 R2 Standard and Datacenter (including
Microsoft SQL Server 2014 and 2016)
• VMware vSphere 5.5 U2 and 6.0
CentOS
NOTE: For more information on the HPE Certified and Supported Hewlett Packard
Enterprise servers for OS and Virtualization Software and latest listing of software
drivers available for your server, please visit our Support Matrix at:
http://www.hpe.com/info/ossupport and our HPE Integrity Superdome X support
page
Mezzanine I/O slots 1 PCIe Gen3 x8 Mezzanine (Type A) slot per Blade (up to 8 Blades)
2 PCIe Gen3 x16 Mezzanine (Type B) slots per Blade (up to 8 Blades)
Flex LOM slots
2 Dual-port NIC FlexLOM daughter cards per Blade (up to 8 Blades)
I/O Interconnect
Bays
Up to 8 I/O Interconnect Bays may contain 1GbE Switch Modules, 20GbE Switch
modules, 10GbE Switch modules, 10GbE Pass-thru modules, 16Gb Fibre Channel and
InfiniBand Interconnect Modules.
Partitioning
Multiple 2, 4, 6*, 8, 12** or one 16-socket electrically isolated HPE nPartitions (HPE
nPars) supported.
NOTE*: BL920s Gen9 blades only
NOTE**: BL920s Gen9 (v4) blades only
Form factor
18U Enclosure
HPE 600 mm wide 42U Intelligent Series rack with standard rack door
High availabilitystandard server
features
2N (N+N) redundant power supplies
N+1 fans (or greater depending on the load)
Online, replaceable, and redundant OA, utilities, clock, and service processor
subsystems
Fault Tolerant Crossbar Fabric built on dynamic multi-pathing and end-to-end retry
technology
Enhanced MCA recovery (Automated Processor Recovery) w/Intel Cache Fail-Safe
Technology®
ECC on caches, Memory ECC, and double-chip spare
ECC, re-tries, and Link Width Reduction on data paths
Automatic de-configuration of memory and processors
I/O Advanced Error Recovery
Redundant network paths
Redundant Fibre Channel paths
Other I/O
•
•
•
1 RS-232 serial port, 2 USB ports, and 1 VGA port for incidental local human
interface via SUV cable
10/100Base-T LAN for Integrity Integrated Lights-Out (iLO 4) management
Removable media via built-in DVD-ROM, accessible from all partitions
Standard Warranty Three year, onsite hardware support – Next Business Day.
Page 7
QuickSpecs
HPE Integrity Superdome X
Standard Features
HPE Superdome X products are comprised of two main components: HPE BladeSystem Superdome Enclosure and the BL920s
Server Blade
HPE BladeSystem
Superdome
Enclosure
The system can be field racked. However, it is strongly recommended that customers order the systems
racked from the factory. This provides the customer the benefit of extensive system testing and avoids
possible premium service charges for field racking service. An important restriction to note about field racked
units: field racked units are limited to single blade configurations due to weight limitations. Additional blades
must be ordered as separate items and will be shipped along with the enclosure. Field racking requires the
use of an appropriate material lift capable of lifting 400 lbs. The RONI lift is no longer available for purchase.
Suggested replacement is the Genie Material Lift GL-8 (http://www.genielift.com/).
Base
Dimensions
Maximum
Lifting
Height
Width –
stowed
Capacity
Weight
2' 10.75"L
Standard
Operating /
5'-7.5" x 35"
Base GL-8
2' 0.75"W
Outside
10 ft. 5 in
2 ft. 0.75 in
400 lbs
132 lbs.
Model No. Description
GL-8
Overall
LxW
HPE Superdome X systems are supported in the HPE 600 mm wide 42U Intelligent Series rack.
Other products may be placed in the same rack as Superdome X. Placement of these other products must not
result in moving the server enclosure.
All racks in the same order must be the same height and width.
HPE Superdome X Hardware Configuration
Superdome Enclosure (AT147B/AT147A)
Number of BL920s Blades (min/max) per compute enclosure
1 to 8
Number of CAMnet Completer modules (CCMs)
0 or 1
Number of processor per compute enclosure (min/max)
2 to 16
(increments of 2)
Number of DIMMs
16, 32 or 48 per Blade
(increments of 16 DIMMs per Blade)
Number of Crossbar Fabric Modules (XFMs)
4
Number of FlexLOM slots
2 slots per Blade
Number of I/O slots
1 Type A Mezzanine slot per Blade
2 Type B Mezzanine slots per Blade
Number of OAs
2
Number of GPSMs (Global Partition Services Modules)
2
DVD module
1
Fans
15
Power Supplies
2N: 12
SUV Dongle cable
1
NOTE: The SUV dongle cable is HPE part number 409496. It connects to the SUV port on the front of each blade and brings out
USB (2 port) serial (DB9) and VGA (DB15). This is how a crash cart or a direct-attached USB DVD is connected for debugging
Page 8
QuickSpecs
HPE Integrity Superdome X
Standard Features
the system.
HPE Superdome X is supported in the HPE 600mm 42U wide Intelligent Series rack with a standard rack door.
Each BL920s blade is populated with one XNC2 Agent chip, two processor modules, and eight Intel Scalable Memory Buffer chips.
Detailed partitioning rules are included in the configuration rules for each system. However, general rules are as follows:
1. Load the largest partitions first, and in accordance with the supported nPAR configurations as documented herein.
2. Odd/even slot loading for BL920s blades in the same partition is required by nPAR sizing rules. For instance, a four blade
partition must have blades loaded in slots 1/3/5/7 or 2/4/6/8 (not slots 1/2/3/4 as in legacy Superdome).
3. A BL920s blade must be in slot 1 of the enclosure.
A BL920s blade or filler blade (HPE CAMnet Completer Module, CCM) must be in slot 2 or 3 of the compute enclosure. A CCM is
needed if there is only a single blade to provide redundant manageability fabric from the GPSMs to the OAs. A CCM is automatically
included in the enclosure, in slot 2, when there is only one compute blade.
Page 9
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
HPE Superdome X
Configuration Rules The HPE BladeSystem Superdome Enclosure is the basic building block for the HPE Superdome X.
Multiple HPE nPartitions (HPE nPars) can be supported in 1-Blade, 2-Blade, 3-Blade (BL920s Gen9 blades
only), 4-Blade, 6-Blade (BL920s Gen9 (v4) only) or 8-Blade configurations.
• Blades can be ordered in single or multiple quantities. A minimum of one BL920s server blade must
be ordered with a Superdome Enclosure and populated in slot 1. If only one blade is ordered, a CCM
must be populated in slot 2 for CAMnet topology redundancy. A CCM is automatically included in
the enclosure when there is only one blade.
• All blades are populated with two processor modules
• A Superdome Enclosure can have up to eight BL920s server blades
• A Superdome Enclosure contains four Crossbar Fabric Modules (XFMs)
• A Superdome Enclosure has two Onboard Administrator (OA) boards populated
• Two Global Partition Services Modules (GPSMs) are included
• There are single phase and three phase power distribution options.
Racking Choices
The HPE Superdome X has some basic racking rules. The Superdome Enclosure is 18U high and can be
racked in the 42U high HPE 600mm wide Intelligent Series rack. The HPE Superdome X may be ordered
field racked, but some disassembly is required.
The default assumption is that compute enclosures are loaded in the rack at the bottom. It is recommended
that 2U is left below the bottom of the compute enclosure in the 42U rack to provide PDU and cabling exit
space.
The supported configuration is a single rack for a Superdome Enclosure at the bottom of the rack leaving
space above for other peripherals.
NOTE: The TFT7600 rack mountable display is not supported with the HPE Superdome X.
Partitioning Choices The HPE Superdome X may be partitioned into different mixes of HPE nPartions – HPE nPARs. The
configurations specified herein allow the customer to hard partition their HPE Superdome X into the
configuration that best suits their computing needs.
The enclosure's midplane has been routed such there is more bandwidth across odd slots and even slots vs.
mixed. Therefore, a four blade partition will have better performance when all four of the blades are in odd (1,
3, 5, 7) or even (2, 4, 6, 8) slots vs. mixed (1, 2, 3, 4) slots.
Below are the configurations when shipped from the factory
HPE Superdome X partition loading
nPartition
Size
1-Blade
2-Blades
3-Blades
4-Blades
6-Blades
8-Blades
ENCLOSURE Slot Number
1
2
3
4
5
6
7
8
1
1
1
1
1
1
5
3
2
2
1
1
2
1
1
1
1
1
6
3
2
2
1
1
3
2
1
1
1
1
7
4
2
2
2
1
4
2
3
1
1
1
8
4
4
2
2
1
NOTE: Support for multiple nPartitions within the enclosure, and those nPartitions can be 1-Blade, 2Page 10
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Blades, 3-Blades*, 4-Blades, 6-Blades* or 8-Blades in size.
NOTE: 3-blade nPartitions (nPars) are only supported with BL920s Gen9 blades
NOTE: 6-blade nPartitions (nPars) are only supported with BL920s Gen9 (v4) blades
Power Distribution The Superdome Enclosure power supplies are 80 PLUS Platinum Rated 2400W supplies.
Options
The Superdome Enclosure is designed to support N+N redundancy of the power supplies. To retain dual
source redundancy in conjunction with the power supply redundancy of Superdome 2, it is necessary to
connect all six power supplies located left of center (three top and three bottom) to one source and all six
power supplies located right of center (three top and three bottom) to the other source.
There are nine AC power connection options offered in Superdome Enclosures. These can be divided into
three main configurations
•
Single Phase only (16A/20A, single phase cords that plug directly into wall sockets)
− Connectors on back of the compute enclosure are IEC60320-C19:
−
•
•
A total of 12 single phase power cords are necessary to power the 12 power supplies in the
Superdome Enclosure. (power option #001)
− To limit the number of power cords exiting the rack (decrease from 12 cords to 4 cords) it
is possible to use a single phase IEC309 63A Power Distribution Units (PDUs) for power
cord aggregation. (power option #006)
− Power option #010 is only available in Japan. There are 6 NEMA L6-30P single phase
PDU's at the bottom of the rack.
NOTE: Power option #010 is not available with the 36u rack.
Below is a photo of the rear of a Superdome Enclosure with the single phase power interface
modules installed, they are visible at the extreme top and bottom of the unit:
Single and Three Phase mix (single phase cables within the rack connected to the PDU, three phase
cables to customer supplied receptacles)
− The power interface modules used are the single phase units shown above.
Page 11
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
−
•
PDUs used have:
 4 wire, IEC 309 60A connector, qty. 2 needed. (power option #004)
 5 wire, IEC309 32A connector, qty. 2 needed. (power option #005)
Three Phase only (three phase cords that connect directly to customer provided receptacles)
 4 wire version utilizes NEMA L15-30R connectors: (power option #002)

−
5 wire version utilizes IEC309 16A 5 pin connectors: (power option #003)
A total of 4 cords are necessary to power the 12 power supplies in the Superdome
Enclosure.
Below is a photo of the rear of a Superdome Enclosure with the three phase power interface modules
installed:
All these options are offered for HPE Superdome X.
All PDUs supported in the HPE Superdome X are half depth such that two can fit in 1U (one in the front and
one in the back). Many of the PDUs are offered in both 1U (horizontally mounted) and 0U (side-mounted)
options. The three phase PDU's for the Superdome Enclosure are AF511A or AF518A.
Specifying power option #007 in conjunction with any of the others (#001 - #006) routes the power cords
to exit the top of the rack rather than the bottom.
Page 12
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Power Option Matrix
Connections to the enclosure
HPE Power Advisor The HPE power Advisor is a tool provided by Hewlett Packard Enterprise to assist in the estimation of power
consumption at a system, rack, and multi-rack level.
Available at: https://paonline56.itcs.hpe.com/
Page 13
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
HPE Superdome X HPE BL920s Server Blades support Intel® Xeon® Processor E7 Family devices as specified in the following
Processor Support tables. For more details on the processor specifications, see: http://ark.intel.com/
Support for the various speed bins is as follows:
BL920s Gen9
Server Blade
Processors
HPE Superdome X BL920s Gen9 supported processor matrix
Processor
Intel Xeon
Processor
E7-8894 v4
Intel Xeon
Processor
E7-8890 v4
Intel Xeon
Processor
E7-8880 v4
Intel Xeon
Processor
E7-8855 v4
Intel Xeon
Processor
E7-8891 v4
Intel Xeon
Processor
E7-8893 v4
# of cores per
processor
24c
Intel® Xeon® Processor E7 v4 Family
Frequency
Cache
Power
2.4 GHz
60 MB
165W
24c
2.2 GHz
60 MB
165W
22c
2.2 GHz
55 MB
150W
14c
2.1 GHz
35 MB
140W
10c
2.8 GHz
60 MB
165W
4c
3.2 GHz
60 MB
140W
Intel® Xeon® Processor E7 v3 Family
Processor
Intel Xeon
Processor
E7-8890 v3
Intel Xeon
Processor
E7-8880 v3
Intel Xeon
Processor
E7-4850 v3
Intel Xeon
Processor
E7-8891 v3
Intel Xeon
Processor
E7-8893 v3
BL920s Gen8
# of cores per
processor
18c
Frequency
Cache
Power
2.5 GHz
45 MB
165W
18c
2.3 GHz
45 MB
150W
14c
2.2 GHz
35 MB
115W
10c
2.8 GHz
45 MB
165W
4c
3.2 GHz
45 MB
140W
HPE Superdome X BL920s Gen8 supported processor matrix
Page 14
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Server Blade
Processors
Processor
Intel Xeon Processor
E7-2890 v2
# of cores
per processor
15c
Intel® Xeon® Processor E7 v2 Family
Frequency
Cache
Power
2.8 GHz
37.5 MB
155W
Intel Xeon Processor
E7-2880 v2
15c
2.5 GHz
37.5 MB
130W
Intel Xeon Processor
E7-4830 v2
10c
2.2 GHz
20 MB
105W
Intel Xeon Processor
E7-8891 v2
10c
3.2 GHz
37.5 MB
155W
Intel Xeon Processor
E7-8893 v2
6c
3.4 GHz
37.5 MB
155W
Processor Mixing
Support
HPE Superdome X governing rules for mixing processors are as follows:
• No mixing of processor types within a nPartition
• No support for processors running at different frequencies or different cache sizes within the same
nPartition
• Processor modules on a blade must be the same revision, frequency, & cache size
• Mixing of processors with different frequencies and/or cache sizes will be NOT allowed within a
nPartition
• You can mix blades of different processor frequencies, cache sizes and generations within a single
enclosure provided each different processor type is in separate nPartitions per the rules listed above.
HPE Superdome X
Memory Support
HPE Superdome X use the Intel® Scalable Memory Buffer chip to translate between the Scalable Memory
Interconnect 2 (SMI2 or VMSE) technology on the memory controller and the DDR3 DIMMs.
The following DIMMs are supported on BL920s Gen9 blades:
• 16GB DDR4-2133 CAS-15-15-15 LRDIMMs for BL920s Gen9 (v3)
• 32GB DDR4-2133 CAS-15-15-15 LRDIMMs for BL920s Gen9 (v3)
• 32GB DDR4-2400 CAS-17 LRDIMMs for BL920s Gen9 (v4)
• 64GB DDR4-2400 CAS-17 LRDIMMs for BL920s Gen9 (v3, v4)
• 128GB DDR4-2400 CAS-17 LRDIMMs for BL920s Gen9 (v4)
The following DIMMs are supported on BL920s Gen8 blades:
• 16GB PC3-12800R (DDR3-1600) Registered CAS-11 DIMMs for BL920s Gen8
• 32GB PC3-14900R (DDR3-1866) Registered CAS-13 DIMMs for BL920s Gen8
Only DIMMs that Hewlett Packard Enterprise has qualified on BL920s Server Blades are supported.
The BL920s Server Blade supports 48 DIMMs and eight Intel® Scalable Memory Buffer chips. This equates to
twelve DIMMs and two Scalable Memory Buffer chips per memory controller (two memory controllers per
processor).
General memory configuration rules:
• For best performance, the amount of memory on each blade within the partition should be the same.
• Use the same amount of memory on each processor module within a partition.
• Use fewer DIMM populations of larger DIMM sizes to get the best performance where possible (use
16x 32GB DIMMs instead of 32x 16GB DIMMs if you need 512 GB of memory per Blade)
HPE Superdome X DIMM loading rules and numbering (top-down view of blade)
Page 15
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
The DIMMs must be loaded in groups of 16 on the Blade, and must be loaded in the following order: A -> B -> C -> D -> E -> F
BL920s Server Blade DIMM Arrangement
NOTE: Per the commonality guidelines, the first DIMMs to be loaded will have white DIMM connector latches loaded on the
blade. Therefore, "A" and "B" connector latches will be white. Connectors in slot positions "C", "D", “E” and “F” will have black
latches.
The following table shows the supported configurations as shipped from the factory
NOTE: Mixing DIMM sizes within the same blade is not supported.
NOTE: For the BL920s Gen8 blade, the 16GB DIMMs are only supported with 16 DIMMs (min/max) per BL920s Gen8 Server
Blade.
Recommended Configurations per BL920s Server Blade
Total
Number of DIMMS
Memory
per Blade
32GB
64GB
(GBytes) 16GB DIMMs DIMMs
DIMMs
256
16
512 (Gen9
32
v3)
512
16
768 (Gen9
48
v3)
1024
32
1024
16
(Gen9)
1536
48
2048
32
(Gen9)
2048
(Gen9)
3072
48
(Gen9)
4096
(Gen9)
6144
(Gen9)
HPE Superdome X
Interconnect
Echelon Echelon Echelon Echelon Echelon Echelon
A
B
C
D
E
F
128GB
DIMMs
16G
16G
16G
16G
32G
32G
16G
16G
16G
16G
16G
16G
32G
32G
32G
32G
64G
64G
32G
32G
32G
32G
64G
64G
64G
64G
128G
128G
64G
64G
64G
64G
32
128G
128G
128G
128G
48
128G
128G
128G
128G
16
16G
16G
32G
32G
64G
64G
128G
128G
HPE Superdome X will support some of the same I/O cards and I/O interconnect modules as the HPE
BladeSystem c7000 and c3000 Enclosures. FlexLOMs and/or Mezzanine I/O cards installed on the Blades are
Page 16
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Module Support
routed through the Superdome Enclosure as depicted in the following picture and table:
NOTE: In order to route the I/O from the FlexLOM and Mezzanine card slots on the individual server Blades, the appropriate
interconnect module must be installed in the appropriate I/O Bay.
Page 17
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Interconnect
Modules
HPE 6127XLG Blade Switch
787635-B21
HPE 6125XLG Ethernet Blade Switch
HPE 10GbE Ethernet Pass-Thru Module II for c-Class BladeSystem
711307-B21
854194-B21
HPE 6125G Ethernet Blade Switch
Cisco B22HP Fabric Extender for BladeSystem c-Class
658247-B21
641146-B21
NOTE: Not available factory integrated in bays 1 & 2; can be factory integrated in bays 38
Cisco B22HP Fabric Extender with 16 FET for BladeSystem c-Class
657787-B21
NOTE: Not available factory integrated in bays 1 & 2; can be factory integrated in bays 38
Brocade 16Gb/28 SAN Switch Power Pack+ for BladeSystem c-Class
Brocade 16Gb/16 SAN Switch for BladeSystem c-Class
HPE 4X FDR InfiniBand Managed Switch for BladeSystem c-Class
C8S47A
C8S45A
648311-B21
NOTE: BL920s Gen9 only
HPE 4X FDR InfiniBand Switch for BladeSystem c-Class
648312-B21
NOTE: BL920s Gen9 only
Converged
Networking
HPE FlexFabric 20Gb 2-port 650M Adapter
HPE FlexFabric 20Gb 2-port 650FLB Adapter
HPE FlexFabric 20Gb 2-port 630FLB Adapter
HPE FlexFabric 20Gb 2-port 630M Adapter
HPE FlexFabric 10Gb 2-port 534M Adapter
NOTE: FlexLOM and Mezzanine I/O cards mentioned are supported in HPE BL920s
Server blades.
NOTE: FlexFabric 534FLB/534M adapters not supported with Windows Server or SQL
Server.
NOTE: FlexFabric 20Gb 2-port 630 & 650 Adapters supported with BL920s Gen9 only.
700767-B21
700763-B21
700065-B21
700076-B21
700748-B21
Networking
HPE Ethernet 10Gb 2-port 560FLB Adapter
HPE Ethernet 10Gb 2-port 560M Adapter
655639-B21
665246-B21
Storage
HPE QMH2672 16Gb Fibre Channel Host Bus Adapter
710608-B21
InfiniBand
HPE InfiniBand FDR 2-port 545M Adapter
702213-B21
NOTE: InfiniBand FDR 2-port 545M Adapter only supported with BL920s Gen9
HPE Superdome X
Boot Support
Fibre Channel is the only supported local disk option
• MSA 2040 is the recommended FC Array, see
https://www.hpe.com/h20195/v2/GetPDF.aspx/c04123144
• Other HPE Fibre Channel storage devices are supported for boot and SAN connectivity. For details,
see the HPE SPOCK website.
Page 18
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
NOTE: For FC, a SAN Switch is required
Each partition (nPar) requires dedicated boot path(s)
• One dedicated FC HBA per partition
• FC: 710608-B21 - HPE QMH2672 16Gb FC HBA
• Two dedicated FC HBAs for Serviceguard
• Dual port HBAs may utilize “second” port for data access
Up to 8 partitions per enclosure
• Minimum partition size = one blade
Superdome X supports PXE boot for network disks
• Can use any of the supported Superdome X 20GbE and 10GbE FlexLOMs or mezzanine cards
Page 19
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Local Boot direct attach FC
NOTE: Information pertains to boot requirements only.
MSA 2040
Enclosure
with SDX
Blades
BladeSystem
FC Switches
Superdome X Chassis
One MSA 2040 SAN can support boot to all partitions
• Use the Explicit Mapping feature of the array to assign boot disks
One MSA 2040 array can support up to two (2) dual port array controllers
• Each controller supports up to four (4) 8/16GB FC links
Considerations for local boot
• Minimum configuration: one controller
− One controller supports boot to all partitions but lacks controller redundancy or online f/w upgrading
• Optimal configuration: two controllers
− Configure redundant boot paths to separate controllers
− Controller firmware may be independently upgraded without taking down the server partitions
Page 20
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
Boot From "Local" SAN
NOTE: Information pertains to boot requirement only.
External
Fibre
Channel SAN
Enclosure
SAN provides essentially unlimited LUNs
Considerations for SAN boot
• Two hops or less strongly recommended
• Redundant paths to SAN/storage recommended for all partitions
• Allows online updates of switch and array firmware
• No factory installation of operating environment
Supported storage devices
HPE Integrity Superdome X currently supports Fibre Channel data connectivity and boot support with the following HPE Storage
devices:
• HPE 3PAR StoreServ 20000/8000/7000/10000 Storage
• HPE MSA 2040 Storage
• HPE XP7 Storage
• HPE XP P9500 Storage
• HPE EVA P6000 Storage
• HPE EVAx400 Storage
For detailed information on supported HPE Storage devices, please visit the HPE SPOCK website.
Platform and Partition Management
Page 21
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
The HPE Superdome X delivers partition administration and control and platform management both in easy-to-use graphical
management tools and also in a comprehensive and concise command-line interface.
The Onboard Administrator in Superdome X is a unique OA option specific to the Superdome Enclosure. It is based on HPE
BladeSystem OA, but adds more memory, more firmware control, and tools designed for platforms using the Superdome Enclosures.
The benefit of reusing the OA is reduced administration costs along with improved platform and partition management, all within a
familiar graphical user interface (GUI) or command line interface (CLI).
The HPE Superdome X has a built-in and always available platform and partition management system. By integrating the
management into the server platform, Hewlett Packard Enterprise ensures that every Superdome X comes with the full set of
management features, and simplifies the task of integrating Superdome X into the data center. The purpose of the HPE Superdome
X management system is to:
• Provide built-in tools to manage hardware and provide mission-critical system availability (inventory, monitor, diagnose,
configure, maintain, and self-healing)
• Make it easier for users and applications to manage partitions (create, modify, inventory, start, stop, connect console, and so
on)
The HPE Superdome X manageability system provides a user-friendly experience, and the OA makes managing the HPE
Superdome X much easier by centralizing the control and building the management into the hardware and firmware of the system. It
provides the following features:
• Intuitive GUI interface makes it easier for system administrators to navigate the intricacies of the HPE Superdome X
management. GUI status displays update automatically when system status changes (dynamic Web technology).
• CLI for easy scripting and power user convenience
• Console for each nPartition, simultaneously available from OA GUI or CLI.
• Sharable enclosure DVD or remotely connected iLO virtual media can be used to attach a DVD-ROM to nPartitions.
• OA controlled power management features across the Superdome X HPE nPartitions
• Built-in Error Analysis Engine constantly monitors all system hardware, analyzes log and telemetry data, and determines
corrective actions for highest system uptime (often performing corrective actions automatically)
• HPE Superdome X OA integrates with Insight Remote Support for data center wide fault management visibility and tie-in to
the HPE support services.
Onboard Firmware
Manager
This functionality can scan a partition and report components with incompatible firmware versions. Single
nPars, or the entire Superdome X, with mismatched firmware due to parts replacements or system upgrades,
can have firmware updated to a consistent level with just a click of a button, and the partitions with
consistent firmware levels fully validated for the most reliable operation.
Onboard Partition
Manager
The Onboard Partition Manager is a set of commands built into the OA
to manage partitions. With these tools, partitions can be built and configured to meet changing workloads as
necessary.
There are three main aspects of partition management:
1. Partition configuration and re-configuration
2. Partition start/stop
3. Management of the OS running on the partition
The Onboard Partition Manager focuses on the first two aspects, partition configuration and partition
start/stop. The core of partition management functionality now resides on the built-in Onboard
Administrator.
The new OA-based partition management architecture supports an nPar management model that is
implemented entirely in firmware. There are no dependencies on software tools, no need for an external
management station or a special "hypervisor" to build your desired partition configuration. The result is
faster, easier, partition configuration and partition start/stop. Both graphical user interface (GUI) and
command line interface (CLI) are supported on the OA to manage partitions.
Page 22
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
The HPE Superdome X can utilize "ParSpecs" which are a way to save, create, and build partitions from
resource definitions. ParSpec definitions allow you to have overlapping resources as long as the partitions
booted don't all claim the same resources at the same time. One way to use ParSpecs is to create one set for
"end of month" jobs, and another set for "daily work". ParSpec commands are built into the OA CLI at first
release.
Step 1: Choose Required Superdome X Enclosure and Power Requirements
Enclosure
HPE Superdome X Base Enclosure
NOTE: Adding Option code "#0D1" to the enclosure will integrate the enclosure into
the Superdome Rack (which must be on the same order)
NOTE: Min 1/Max 1 Power Option #001 - #006, #010 must be selected.
Option #007 - can be added if power is out of the top of the rack
NOTE: Min 1/Max 1 Superdome X partitioning LTU is required for each enclosure
ordered. See HPE Superdome X system software listed below.
Power options
HPE Superdome X Local Power
HPE Superdome X 4 Wire No PDU
HPE Superdome X 5 Wire Intl No PDU
HPE Superdome X 4 Wire 3 Phase PDU
HPE Superdome X 5 Wire Intl 3 Phase PDU
HPE Superdome X 3 Wire Local SP PDU
HPE Superdome X Top Power
HPE Superdome X 3 Wire Japan SP PDU
Enclosure upgrade
HPE Superdome X Crossbar Fabric 2 Module
NOTE: The HPE Superdome X Crossbar Fabric 2 Module can be used to upgrade the
AT147A enclosure to the AT147B enclosure. The upgrade is not required but may
provide up to 33% greater bandwidth for some high-end configurations
AT147B
#001
#002
#003
#004
#005
#006
#007
#010
H7B49A
Step 2: Choose Interconnect Module Options
NOTE: Select minimum one (1) and maximum eight (8)
Networking modules NOTE: Select minimum one (1) and maximum eight (8) networking modules
NOTE: If the HPE BLc 10GbE pass-thru module (538113-B21 or 854194-B21) is
installed in slots 1 or 2 of the enclosure, then the HPE FlexFabric 10Gb 2P 534FLB
adapter (700741-B21) cannot be installed in any blade.
HPE 10GbE Ethernet Pass-Thru Module II for c-Class BladeSystem
854194-B21
HPE 6127XLG Blade Switch
787635-B21
HPE 6125XLG Ethernet Blade Switch
HPE 6125G Ethernet Blade Switch
Cisco B22HP Fabric Extender for BladeSystem c-Class
711307-B21
658247-B21
641146-B21
NOTE: Not available factory integrated in bays 1 & 2; can be factory integrated in bays
3-8
Cisco B22HP Fabric Extender with 16 FET for BladeSystem c-Class
657787-B21
Page 23
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
NOTE: Not available factory integrated in bays 1 & 2; can be factory integrated in bays
3-8
Storage modules
Brocade 16Gb/28 SAN Switch Power Pack+ for BladeSystem c-Class
Brocade 16Gb/16 SAN Switch for BladeSystem c-Class
NOTE: Select minimum one (0) and maximum six (6) storage modules
InfiniBand modules
HPE 4X FDR InfiniBand Managed Switch for BladeSystem c-Class
648311-B21
HPE 4X FDR InfiniBand Switch for BladeSystem c-Class
648312-B21
C8S47A
C8S45A
NOTE: Select minimum one (0) and maximum two (2) InfiniBand modules
NOTE: Double-Wide (consumes 2 bays)
NOTE: Supported with BL920s Gen9 only
Step 3: Choose BL920s Server Blades and options
HPE BL920s Gen9
(v4) Server Blades
HPE Superdome X BL920s Gen9 E7-8894v4 2.4GHz 48-core Server Blade
HPE Superdome X BL920s Gen9 E7-8893v4 3.2GHz 8-core Server Blade
HPE Superdome X BL920s Gen9 E7-8891v4 2.8GHz 20-core Server Blade
HPE Superdome X BL920s Gen9 E7-8890v4 2.2GHz 48-core Server Blade
HPE Superdome X BL920s Gen9 E7-8880v4 2.2GHz 44-core Server Blade
HPE Superdome X BL920s Gen9 E7-8855v4 2.1GHz 28-core Server Blade
NOTE: Select minimum one (1) and maximum eight (8) server blades
NOTE: All server blades in a partition must be identical
NOTE: Min1/Max 1 iLO Advance LTU per blade
Q1F43A
H7B44A
H7B45A
H7B46A
H7B47A
H7B48A
HPE BL920s Gen9
(v3) Server Blades
HPE Superdome X BL920s Gen9 8890 2.5GHz 36-core Server Blade
HPE Superdome X BL920s Gen9 8880 2.3GHz 36-core Server Blade
HPE Superdome X BL920s Gen9 8891 2.8GHz 20-core Server Blade
HPE Superdome X BL920s Gen9 4850 2.2GHz 28-core Server Blade
HPE Superdome X BL920s Gen9 8893 3.2GHz 8-core Server Blade
NOTE: Select minimum one (1) and maximum eight (8) server blades
NOTE: All server blades in a partition must be identical
NOTE: Min1/Max 1 iLO Advance LTU per blade
A0R98A
H7B40A
A0S01A
A0R99A
H7B43A
HPE BL920s Gen8
Server Blades
HP Superdome X BL920s Gen8 2890 2.8GHz 30-core Server Blade
HP Superdome X BL920s Gen8 2880 2.5GHz 30-core Server Blade
HP Superdome X BL920s Gen8 8891 3.2GHz 20-core Server Blade
HP Superdome X BL920s Gen8 4830 2.2GHz 20-core Server Blade
HP Superdome X BL920s Gen8 8893 3.4GHz 12-core Server Blade
NOTE: Select minimum one (1) and maximum eight (8) server blades
NOTE: All server blades in a partition must be identical
NOTE: Min1/Max 1 iLO Advance LTU per blade
AT068A
A0R97A
B9F03A
B9F04A
H7B42A
HPE DDR4 memory
HPE Superdome X DDR4 128GB (4x32GB) PC4-2400 Load Reduced CAS-17 Memory
Kit
H7B82A
Page 24
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
modules for BL920s HPE Superdome X DDR4 256GB (4x64GB) PC4-2400 Load Reduced CAS-17 Memory
Kit
Gen9 (v4) blades
HPE Superdome X DDR4 512GB (4x128GB) PC4-2400 Load Reduced CAS-17 Memory
Kit
NOTE: No mixing of DIMM capacities on individual Blades
NOTE: Memory modules must be ordered in multiples of 4
NOTE: Minimum 4/ maximum 12 modules per blade
NOTE: Q1F79A is in pre-release status and requires approval before ordering; expect
longer than normal lead times.
H7B83A
HPE DDR4 memory HPE Superdome X DDR4 64GB (4x16GB) PC4-2133 Load Reduced CAS-15 Memory
modules for BL920s Kit
Gen9 (v3) blades
HPE Superdome X DDR4 128GB (4x32GB) PC4-2133 Load Reduced CAS-15 Memory
Kit
HPE Superdome X DDR4 256GB (4x64GB) PC4-2400 Load Reduced CAS-17 Memory
Kit
NOTE: No mixing of DIMM capacities on individual Blades
NOTE: Memory modules must be ordered in multiples of 4
NOTE: Minimum 4/ maximum 12 modules per blade
A0S02A
HPE DDR3 memory NOTE: No mixing of DIMM capacities on individual Blades
modules for BL920s NOTE: Memory modules must be ordered in multiples of 4
Gen8
NOTE: Windows Server and SQL Server have a maximum memory capacity of 4TB per
partition
HP Superdome X 64GB (4x16GB) PC3-12800R (DDR3-1600) Registered CAS-11
Memory
NOTE: Minimum 4/ maximum 4 modules per blade
HP Superdome X 128GB (4x32GB) PC3-14900R (DDR3-1866) Registered CAS-13
Memory
NOTE: Minimum 4/ maximum 12 modules per blade
Blade FlexLOM
HPE Networking
Mezz cards
NOTE: Minimum 1/ maximum 2 per blade
HPE FlexFabric 20Gb 2-port 630FLB Adapter
HPE FlexFabric 20Gb 2-port 650FLB Adapter
NOTE: BL920s Gen9 only
HPE Ethernet 10Gb 2-port 560FLB Adapter
NOTE: BL920s Gen8 only
NOTE: FlexFabric 534FLB adapter not supported with Windows Server or SQL Server
HPE FlexFabric 20Gb 2-port 630M Adapter
HPE FlexFabric 20Gb 2-port 650M Adapter
NOTE: BL920s Gen9 only
NOTE: Min 0/ Max 3 per blade
HPE Ethernet 10Gb 2-port 560M Adapter
NOTE: Min 0/ Max 1 per blade
HPE FlexFabric 10Gb 2-port 534M Adapter
NOTE: BL920s Gen8 only
NOTE: Min 0/ Max 1 per blade
NOTE: FlexFabric 534M adapter not supported with Windows Server or SQL Server
Q1F79A
H7B38A
H7B83A
B9F08A
B9F09A
700065-B21
700763-B21
655639-B21
700076-B21
700767-B21
665246-B21
700748-B21
Page 25
QuickSpecs
HPE Integrity Superdome X
Ordering and Configuration
HPE Fibre Channel
mezz cards
HPE QMH2672 16Gb Fibre Channel Host Bus Adapter
NOTE: Minimum 0/ maximum 3 per blade
710608-B21
InfiniBand mezz
cards
HPE InfiniBand FDR 2-port 545M Adapter
702213-B21
NOTE: BL920s Gen9 only
NOTE: Minimum 0/ maximum 2 per blade
HPE Superdome X
system software
HPE Superdome X Basic Partitioning LTU
HPE Superdome X Advanced Partitioning LTU
HPE Superdome X Advanced Partitioning Upgrade LTU
HPE Superdome X Advanced Partitioning Upgrade E-LTU
NOTE: If 5 or more blades are ordered OR More than 1 partition is selected, then
AT152A is required
NOTE: AT150A or AT152A can be ordered with 4 blades or less with a single partition
NOTE: Min 1/Max 1 Superdome X partition LTU (AT150A or AT152A) required per
enclosure ordered
HPE iLO Advanced
NOTE: Min 1/Max 1 iLO Advanced license required per blade
HPE iLO Advanced including 3yr 24x7 Tech Support and Updates 1-server LTU
HPE iLO Adv incl 3yr TS U E-LTU
AT150A
AT152A
AT154A
AT154AAE
BD505A
E6U64BE
Page 26
QuickSpecs
HPE Integrity Superdome X
Technical Specifications
This section describes the physical and environmental information.
HPE Superdome X
NOTE: Site planning and installation included.
System Unit
Dimensions
Height
Width
Depth
798 mm / 31.4" (18U)
485 mm / 19.1"
828 mm / 32.6"
Weight
Minimum
(empty chassis with midplane
assembly and rear chassis
cage)
Typical
(half populated)
Maximum (fully populated)
108 kg / 238 lb (empty chassis with midplane assembly
and rear chassis cage)
BTU Rating
Maximum Heat dissipation
(fully populated system)
30.93 kBTU//hr (2.5 Tons) , 9065W
Electrical
Characteristics
AC input power: 3-phase
Environmental
Characteristics
Acoustics
<= 8.6 bels LwAd (Sound Power)
Temperature - Recommended +18°C to +27°C
Operating Range
Temperature - Allowable
+5°C to +40°C
Operating Range
Maximum rate of temperature 20°C/hr
change
Non-operating temperature -40°C to +80°C
(storage)
Air quality
Gaseous contaminants must be at the G1 level or less
as defined by ISA Standard ISA-71.04-1985
Humidity - Recommended
+5.5 °C DP to 15°C DP and 65% RH
Operating Range (noncondensing)1
Humidity - Allowable
-12 °C DP and 8% RH to 24 °C DP and 85% RH
Operating Range (noncondensing)1
254 kg / 559 lb
314 kg / 692 lb
2N Dual Power input modules with two 5-wire cords
each: IEC309 16A or two 4-wire cords each: NEMA
L15-30P 30A. 5 wire: 12.26A per cord. 4wire: 23.3A per
cord
AC input power: Single-Phase 2N Dual Power input modules with 6 Input Receptacles
each: IEC-C19, 16/20A.
Maximum Input Current:
13.8A per C19 cord
Single Phase (200V)
Maximum Input Power total 9,250 VA at PF .98 or greater
Cooling airflow
600 CFM min; 1000 CFM@32 deg. C avg; 1900 CFM
max
Page 27
QuickSpecs
HPE Integrity Superdome X
Technical Specifications
Non-operating relative
8% RH to 90% RH and 32 °C DP
humidity (storage)
Maximum Operating altitude 3050m (10,000 ft)
Maximum Non-operating
4500m (15,000 ft)
altitude (storage)
Voltage tolerance range
200-240 VAC
NOTE: The Recommended Operating Range is recommended for continuous
operation. Operating within the Allowable Operating Range is supported but may
result in a decrease in system performance.
NOTE: All temperature ratings shown are for sea level. An altitude de-rating of 1°C
per 300 m above 900 m is applicable. No direct sunlight allowed. Upper operating
limit is 3,048 m (10,000 ft).
Environmental Info Regulatory model numbers:
AT147A/AT147B (Superdome Enclosure), RMN: FCLSB-1001
AT068A (BL920s Gen8 Server Blade), RMN: FCLSB-BB31
Additional Power
Data
The maximum power figures given were developed with the maximum configuration
running applications designed to draw the maximum power possible. It is highly
unlikely that any real-world application will result in this amount of power use for any
significant time period.
Page 28
QuickSpecs
HPE Integrity Superdome X
Summary of Changes
Date
23-Oct-2017
Version History
From Version 16 to 17
Action
Changed
07-Aug-2017
From Version 15 to 16
Changed
Added
Removed
27-Mar-2017
From Version 14 to 15
Changed
Added
Removed
23-Sep-2016
From Version 13 to 14
Changed
24-Jun-2016
From Version 12 to 13
Changed
06-Jun-2016
From Version 11 to 12
Changed
Added
11-Mar-2016
From Version 10 to 11
Changed
Added
08-Jan-2016
From Version 9 to 10
Changed
Added
09-Oct-2015
From Version 8 to 9
Changed
28-Sep-2015
From Version 7 to 8
Changed
Added
17-Jul-2015
From Version 6 to 7
Changed
Added
Removed
19-Jun-2015
1-Jun-2015
From Version 5 to 6
From Version 4 to 5
Changed
Added
Changed
27-Feb-2015
From Version 3 to 4
Changed
16-Jan-2015
1-Dec-2014
From Version 2 to 3
From Version 1 to 2
Changed
Changed
Description of Change
Care Pack naming and Service and Support- Parts and Materials
updated.
Ordering and Configuration section was updated.
SKU was added in Ordering and Configuration section:
854194-B21
SKU was removed from Ordering and Configuration section:
538113-B21
Overview, Standard Features, and Ordering and Configuration.
SKUs added in Ordering and Configuration section:
700741-B21, AT147A, H7B39A.
Obsolete SKUs deleted from Ordering and Configuration section:
700767-B21, 700763-B21, Q1F43A, H7B83A, Q1F79A.
Standard Features and Ordering and Configuration sections were
updated.
Service and Support, Standard Features, Ordering and
Configuration, and Technical Specifications.
Overview, Standard Features, Ordering and Configuration, and
Technical Specifications sections were updated.
SKUs added in Ordering and Configuration section:
AT147B, H7B49A, H7B44A, H7B45A, H7B46A, H7B47A,
H7B48A, H7B82A, 700763-B21, 700767-B21.
Overview, Standard Features, Ordering and Configuration, and
Service and Support, sections were updated.
SKUs added to QuickSpecs:
641146-B21, 657787-B21, 700076-B21
QuickSpecs updated and rebranded.
SKU added in Ordering and configuration section:
787635-B21
Overview, Service and Support, HPE Care Pack, and Warranty
Information, standard, features, ordering and configuration.
Ordering and Configuration, Overview and Standard Features
sections were updated.
SKUs added:
C8S45A, 648311-B21, 648312-B21, 700065-B21, 702213B21, 648311-B21, 648312-B21, A0R98A, H7B40A, A0S01A,
A0R99A, H7B43A, A0S02A, H7B38A, 700076-B21, 702213B21
Standard Features, Ordering and Configuration sections were
updated.
SKUs added in Ordering and Configuration Section:
BD505A, E6U634BE
SKUs deleted in Ordering and Configuration Section:
BD502A, E6U63ABE
Ordering and Configuration section was updated
SKU added to Ordering and Configuration:
H7B42A
Standard Features Ordering and Configuration sections were
updated.
Standard Features and Ordering and Configuration sections were
updated.
Changes were made throughout the QuickSpecs
Name change to HPE Integrity Superdome X, several changes
were made throughout the QuickSpecs
Page 29
QuickSpecs
HPE Integrity Superdome X
Summary of Changes
Removed
SKU removed:
658247-B21
Sign up for updates
© Copyright 2017 Hewlett Packard Enterprise Development LP. The information contained herein is
subject to change without notice. The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise
shall not be liable for technical or editorial errors or omissions contained herein.
Hewlett Packard Enterprise makes no warranties for non-Hewlett Packard Enterprise products.
Intel and Xeon are US registered trademarks of Intel Corporation.
c04383189 - 15028 - Worldwide - V17 - 23-October-2017
Page 30