32107 manual-EN - KRAFTWERK Tools

Using-Instructions
CORDLESS DRILL/DRIVER 10.8 V
EN
WARNING:
DO NOT attempt to operate the tool until you have read and understood all
instructions and safety rules contained in this manual. Failure to comply
may result in accidents involving fire, electric shock, or serious personal
injury. Save this owner’s manual for future reference and review it
frequently for safe operation.
www.KRAFTWERKtools.com
Art. 32107
2
3
c) Keep children and other persons away while
operating a power tool. Distractions can cause
you to lose control.
tightening and
outlets will reduce the risk of electric shock.
minors
or dark areas can lead to accidents.
Disordered
environments with flammable liquids, gases
or dust. Power tools create sparks which may
ignite dust or fumes.
4
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or placing power tools. Such
preventive safety measures reduce the risk of
starting the power tool unintentionally.
d) Store unused power tools out of reach of
children and do not allow persons not familiar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of inexperienced users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Use the power tool, accessories and drill
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
a) Do not overload the power tool. Use the
correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or
fire.
b) Do not use the power tool if the switch
is out of function. Any power tool that
cannot be controlled by the switch is dangerous
and must be repaired.
5
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
• Keep your workplace clean. Mixing of
materials is particularly dangerous. Light
metal dusts easily can burn or explode.
6) Service
• Always wait until the machine has come to
a complete stop before placing it down. The
inserted tool can jam and lead to loss of control
over the power tool.
a) let your power tool be repaired by a qualified
service person using only original service/spare
parts. This will ensure that the safety of the
power tool is maintained.
• Do not open the battery. Danger of
shortcircuiting. Protect the battery against heat,
e. g., also against continuous sun exposure
and fire. There is danger of explosion.
4. Special safety instructions
• In case of damage and improper use of the
battery, vapours may be emitted. Provide
for fresh air and seek medical help in case
of complaints. The vapours can irritate the
respiratory system.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory or fastener may
contact hidden power lines. Cutting accessory
and fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
• When the battery is defective, liquid can
escape and come into contact with adjacent
components. Check any parts concerned.
Clean such parts or replace them, if required.
• Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local electric company for assistance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
• Switch off the power tool immediately
when the inserted tool jams and blocks. Be
prepared for high reaction torque that can cause
a kickback.
The inserted tool jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
• Hold the machine with a firm grip. High
reaction torque can briefly occur while
tightening in and loosening screws.
• Secure the workpiece. A workpiece fixed
with clamping devices or in a vice is held
more securely than by hand.
6
1. Torque selector
2. Rotation selector switch
3. On/Off switch
4. Li-ion battery pack
5. Battery holder
6. Selector switch for 1st/2nd gear
7. Quick-change drill chuck
8. Battery charger
9. LED lamp
10. Integrated magnetic bit holder
11. Battery capacity indicator
7. Before starting the equipment
Be sure to read the following information before
you use your cordless screwdriver for the first
time:
1. Charge the battery pack with the supplied
charger. An empty battery pack requires a
charging time of approximately 100 min.
2. Only ever use sharp drill bits and driver
bits which are suitable for the purpose and in
flawless condition.
Battery-packs are resuable resources
Li-Ion battery
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing
in walls.
Avoid continous sun exposure
Do not throw into fire
8.1 Charging the battery pack (B2-B3)
The battery is protected against total discharge.
The integrated protective system will automatically switch off the machine when the battery is
completely discharged. In this case the bit holder
is not turning anymore.
Do not throw into water
Waste electrical equipment contains
valuable materials and they do not
belong to household waste.
We kindly ask you to help to protect the
environment by returning this machine
to a return point (if available) after
reaching the end of its life.
Warning!
Don’t use the ON/OFF switch any longer if the
integrated protective system switched off the
machine. This could lead to damage the battery.
Used batteries do not belong to
household waste. There is the legal
obligation to return batteries to
appropriate recycling points.
1. Remove the battery pack (4) from the handle
pressing the pushlock buttons (5) on the left and
the right side.
7
last step ,,Drill". In this setting the slip clutch is
inactive. The maximum torque is available in
drilling mode.
2. Check that your mains voltage is the same as
marked on the rating plate of the battery
charger. Plug the mains plug of the charger (8)
into the mains socket outlet. The green LED
starts to flash.
8.4 Forward/Reverse switch (B5)
With the slide switch above the ON/OFF switch
you can select the direction of rotation of the
battery powered drill/screwdriver and secure it
against being switched on unintentionally. You
can choose between clockwise and anticlockwise rotation. To avoid causing damage to the
gear box change the direction of rotation only
when the tool is at standstill.
3. Insert the battery (4) on the charger (8).
4. Under point 8.10 „ Indication of charger“ you
find a table with the meanings of the
LED-indication for the charger.
If the battery pack fails to become charged,
please check whether there is voltage at the
socket-outlet - whether there is proper contact
at the charging contacts on the charger (8).
If the battery still fails to become charged, please
deliver the charger and the battery pack to our
Customer Service Department. To ensure that
the battery pack provides long service you
should take care to recharge it promptly. You
must recharge the battery pack when you notice
that the power of the cordless screwdriver drops.
Never fully discharge the battery pack. This will
lead the battery pack to damage.
The ON/OFF switch is blocked when the slide
switch is in centre position.
8.5 On/Off switch (B5)
Variable speed control is possible with the
On/Off switch. More you press the switch, higher
gets the speed of the battery powered
drill/screwdriver.
Power up:
Press for starting the machine the ON/OFF
switch (3) and hold down the button. The
LED-light (9) lights up with slightly or completely
pressed ON/OFF switch (3) and enables to
illuminate the work area.
Attention! Recharge the battery at regular
intervals (for example every 6 months).
8.2 Torque setting (B4)
The cordless screwdriver is fitted with a
mechanical torque selector. The torque for a
specific size of screw is selected with the
set-collar (1). The correct torque depends on
several factors:
- the type and hardness of material in question
- the type and length of the used screws
- the requirements to be applied on the screw
connection.
Power down:
Release the ON/OFF switch (3) for turning off the
machine.
8.6 Battery capacity indicator (B1)
The 3 color LEDs are indicating the status of the
battery capacity as soon as you press the
ON/OFF switch (3).
All LEDs illuminate: The battery is fully charged.
The yellow and red LED illuminate: The battery
has an adequate remaining charge. Red LED: The
battery is empty, recharge the battery.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
8.7 LED lamp (B5)
The LED lamp (9) can be used in poor lighting
conditions to illuminate the area to drill or screw.
The LED lamp (9) will be lit
automatically as soon as you press the ON/OFF
switch (3).
8.3 Drilling (B4)
For drilling purposes, move the set-collar to the
8
8.8 Changing the tool (B6)
Important! Set the rotation selectorswitch (2) to
its centre position whenever you carry out any
work (for example changing the tool, maintenance work, etc.) on the cordless screwdriver.
To use them you have to remove the quickchange drill chuck (7) by pressing the rear drill
chuck sleveve (b) to the drill chuck.
Now you can put the appropriate bit into the
integrated magnetic bit holder (10).
- The cordless screwdriver is fitted with a
quick change chuck (7) with an automatic
spindle stop.
In order to mount the drill chuck again you have
to put it on the bit holder and turn it a little until
it can be defered completely. Lock the drill chuck
by pushing the drill chuck sleeve (b) to the
direction of the machine.
- Open the chuck (7). The chuck opening (a) must
be big enough to hold the tool (drill bit or
screwdriver bit).
9. Technical data
- Select the suitable tool. Push the tool as deep
as possible into the chuck opening (a).
Voltage supply:
10.8 V d.c. / 2.0 Ah Li-Ion
Idle speed:
0-400/0-1400 rpm
Torque settings:
18+1
Max. torque:
25 Nm
Forward and reverse rotation:
yes
Chuck clamping capacity:
0.8-10 mm
Battery charging voltage:
13.5 V d.c.
Battery charging current:
1500 mA
Mains voltage for charger: 100-240 V~/50-60 Hz
Charging time:
100 min
- Tighten the chuck (7) and then check that the
tool is secure.
8.9 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that
matches the screw in shape and size. Set the
torque, as described in these operating
instructions, to suit the size of screw.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745-1, EN 60745-2-1,
EN 60745-2-2.
LpA sound pressure level
61.8 dB(A)
3 dB
KpA uncertainty
72.8 dB(A)
LWA sound power level
3 dB
KWA uncertainty
8.10 Indication on battery charger
Slide the battery on the charger. The red LED
signalized that the battery is fully charged.
If the charge status is terminated the red LED
goes out and the green LED then lights
constantly.
8.11 Changing from 1st gear to 2nd gear
(B4/Pos.6)
Information: Push the gear switch 6 only when
the machine is at stillstand. In first gear (gear
switch 6 in position 1) you obtain a speed of
about 400 rpm and a high torque. This setting is
ideal for all screwing actions. In the second gear
(gear switch 6 in position 2) you obtain a speed
of about 1400 rpm for drilling operations.
Wear ear-muffs.
The impact of noise can cause hearing loss.
Total vibration values (vector sum of three
directions) determined in accordance with
EN 60745-1, EN 60745-2-1, EN 60745-2-2.
Drilling in metal
Vibration emission value ah = 0.495 m/s2
K uncertainty = 1.5 m/s2
8.12 Integrated magnetic bit holder (B.7-8)
The cordless drill/driver has an integrated
magnetic bit holder (10) for ¼“ (6.35 mm) bits.
Screwing without hammer action
Vibration emission value ah <2.5 m/s2
K uncertainty = 1.5 m/s2
9
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device.
Important!
The vibration value changes according to the area
of application of the electric tool and may exceed
the specified value in exceptional circumstances.
12.2 Maintenance
10. Repairs
There are no parts inside the equipment which
require additional maintenance.
Only use accessories and spare parts
recommended by the manufacturer.
If the equipment should fail some day in spite of
our quality controls and your maintenance, only
let it repair by an authorized electrical specialist.
If the supply cord of the appliance is damaged,
this has to be done by the manufacturer or his
agent or electrician in order to avoid a safety
hazard.
11. Environmental protection
Waste electrical equipment contains
valuable materials and they do not
belong to household waste.
We kindly ask you to help to protect the
environment by returning this machine
to a return point (if available) after
reaching the end of its life.
Used batteries do not belong to
household waste. There is the legal
obligation to return batteries to
appropriate recycling points.
12. Cleaning and maintenance
Always pull out the mains power plug before
starting any cleaning work.
12.1 Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
out with compressed air at low pressure.
• We recommend that you clean the device
immediately each time you have finished using it.
10
DECLARATION OF CONFORMITY
Model: 32107
Cordless drill/driver 10.8 V
KRAFTWERK Sàrl, 25 rue due Stade, F-67870 Bischoffsheim
Declares under sole responsibility that the product to which this declaration relates is in conformity with the following
standard(s) or other normative document(s): EN 55014-1: 2006+A1/2009+A2/2011
EN 55014-2: 1997+A1/2001+A2/2008
EN 60745-1: 2009+A11/2010
EN 60745-2-1: 2010
EN 60745-2-2: 2010
EN 60335-1: 2012
EN 60335-2-29: 2004+A2/2010
EN 62233: 2008
Following the provisions of Directive(s)
Machinery Directive:
2004/108/EC
2006/42/EC
2006/95/EC
Bischoffsheim, 28/01/2016
Patrick Wyss
President
www.KRAFTWERKtools.com
11
KRAFTWERK Europe AG
Mettlenbachstrasse 23
CH-8617 Mönchaltorf
Switzerland
Tel. +41-44 949 40 50
KRAFTWERK Sàrl.
25, rue du Stade
F – 67870 Bischoffsheim
France
Tel. +33-388 48 64 50
www.KRAFTWERKtools.com
Download PDF

advertising