Mobile Antennas
Cellular Band Aerials
There are a number of models available to provide enhanced operation for the Cellular
Band. For sites where a gain aerial is required, the omnidirectional Collinear (CELBS6) or
the directional 10dB gain Yagi (CY10C) is recommended.
The Collinear (CELBS6) is a vertically polarised omnidirectional aerial giving 6dB of gain. It
is housed in a 1.2 metre high tapered fibreglass radome, and as standard is fitted with 3
metres of low loss coaxial cable. The aerial is mounted with its 12mm stud. For marine
installations the above 6dB Collinear is available with a fully adjustable Marine Tilt (CELM6).
Please specify when ordering service required e.g. XT or 021 GSM network.
The Cellular Yagi (CY10C) has 10 elements giving 10dB of gain. It is constructed with an
aluminium channel boom, and the driven element and matching system is totally
encapsulated. Three metres of low loss coaxial cable is supplied as standard. All parasitic
elements are 6.5mm diameter aluminium rod. The cast aluminium mounting clamp and
stainless steel hardware enables the yagi to be clamped to a 25mm fascia mount. Please
specify when ordering service required e.g. XT or 021 GSM network.
The Coaxial 1/2 Wave Aerial (CX-825), is a ground independent aerial and can be mounted
in any location on a vehicle. It is slim in appearance and has an overall height of approx
480mm. It gives 3dB of gain and is mounted with a 12mm stud onto the right angle bracket
(BRRA1/2). This aerial is supplied pretuned to your specified band. A 6dB element is
available on request for the (CX-825)
The aerial can also be raised in height by using the Extender (MEXT), this allows the aerial
to clear vehicle body panels and improve performance. Three metres of low loss coaxial
cable is fitted as standard.
A 4dB black stainless steel Collinear Whip Aerial (CELCOL4) is also available. This mounts
onto the Aerial Base (VHFB) with the Adaptor (AW12) and requires a ground plane
mounting for correct operation.
For tuning CELCOL4 see guide Appendix 1
www.hi-tec-aerials.co.nz
E: sales@hi-tec-aerials.co.nz
P: 03 384 3375 F: 03 982 3376
1/14 Kennaway Rd, Woolston, Christchurch
98
Mobile Antennas
MODEL
Description
CELBS6
Cellular Base Station Aerial - 6dB
Gain
CELCOL4
Cellular Collinear Mobile Whip
Aerial - 4dB Gain
CELM6
Cellular Marine Aerial With Tilt 6dB Gain
CY10C
Commercial Yagi 10 Element Cellular Bands XT or 021 Networks
CX-825
Coaxial 1/2 Wave Aerial 3dB gain
XT Network
CX-900
Coaxial ½ Wave Aerial 3dB gain 021
GSM & ISM
1/2CELL
1/2 Wave flexible, Cellular band and
ISM
CX 825, CX 900
1/2CELL
CELCOL4
CELBS6
CY10C
CELM6
www.hi-tec-aerials.co.nz
E: sales@hi-tec-aerials.co.nz
P: 03 384 3375 F: 03 982 3376
1/14 Kennaway Rd, Woolston, Christchurch
99
Mobile Antennas
Cellular Band Aerials
These stylish ground dependant bases and elements are supplied complete with a 4
metre FME to FME cable. FME (adaptor) connectors are available on request. This range
of antennas can be direct mounted on to the vehicle panel or a bracket can be used. (BRM)
MODEL
Description
CEP-027-021
Cellular 021 & 027 Networks, Tri Band, Unity gain
CEP-021-3
Cellular 021 Network, Dual band, 3dB gain
CEP-021-6
Cellular 021 Network, Single band, 6dB gain
CEP-027-021
CEP-021-3
CEP-021-6
www.hi-tec-aerials.co.nz
E: sales@hi-tec-aerials.co.nz
P: 03 384 3375 F: 03 982 3376
1/14 Kennaway Rd, Woolston, Christchurch
100
Mobile Antennas
Cellular Band Collinear Aerials
These models are vertically polarised omnidirectional 6dB lightweight antennas for base
station or marine applications, where improved performance is required for cellular band operation.
The radiating element is housed in a tapered fibreglass radome for low wind loading. Low
loss coaxial cable is fitted to minimise feed line losses. When the antenna is installed, the
cable should be kept as short as possible as cable attenuation of 2dB per 10 meters is typical at these frequencies.
Two mounting options are available for this model, a stud mount for the base station
application, complete with a right angle bracket (BRRA1/2) or a dual directional tilt mount,
for marine use.
Specification:
MODEL
CELM6
CELBS6
Frequency Range
(MHz)
800-900
Bandwidth (MHz)
25
Gain (dBd)
6
Input Impedance
(Ohms)
50
Cable Type &
Length
RG58 Low Loss 9006, 3m
Maximum Power
(W)
50
Height (m)
1.2
Projected Area
(m2)
Weight (kg)
Mounting
0.016
0.015
0.6
0.5
Marine Tilt
S/S Bracket
CELM6
CELBS6
www.hi-tec-aerials.co.nz
E: sales@hi-tec-aerials.co.nz
P: 03 384 3375 F: 03 982 3376
1/14 Kennaway Rd, Woolston, Christchurch
101
Download PDF

advertising