RAYDEN DMX
QUICKSTART GUIDE
Rayden Bi-Color DMX Flat Panel Light
RBX5
Rayden Bi-Color LED Half x 1 Soft Light with DMX
RBX10
Rayden Bi-Color LED 1 x 1 Soft Light with DMX
What’s Included
1 x 15V Power supply
1 x Yoke Mount
CHECKED BY
www.ikancorp.com
support@ikancorp.com
713.272.8822
© 2017 ikan Corporation. All rights Reserved
General Information
Thank you for buying the ikan Rayden Bi-Color DMX512 LED Lights. This fixture has been designed to perform reliably for
years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use
and maintenance.
Every fixture has been thoroughly tested. Carefully check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary
to operate the unit have arrived intact. In the event damage has been found or parts are missing, please contact our customer
support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at
the number listed below. Please do not discard the shipping carton in the trash. Please recycle whenever possible.
Safety Instructions:
This fixture is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to
follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the
misuse of this fixture due to the disregard of the information printed in this manual.
This device falls under PROTECTION CLASS 1. It’s essential this device be grounded properly. Only qualified personnel should
perform all electrical connections.
INDOOR USE ONLY!
DO NOT EXPOSE FIXTURE TO RAIN AND/OR MOISTURE!!
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
For proper operation, follow the Installation guidelines described in this manual. Only qualified and certified personnel should
perform installation of this fixture and only the original rigging parts (yoke) included with this fixture should be used for installation.
Any modifications will void the original manufacture’s warranty and increase the risk of damage and/or personal injury.
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce blindness.
Always disconnect from main power source before performing any type of service and/or cleaning procedure. Only handle the
power supply by the plug end, never pull out the plug by tugging the wire portion of the cord.
Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If the power
cord is damaged, replace it immediately with a new one of similar power rating.
General Guidelines:
NEVER OPEN THIS FIXTURE WHILE IN USE!!
Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating, to prevent any fire hazard.
The fixture must be installed in a location with adequate ventilation, at least 1.5 feet (.5m) from adjacent surfaces. Be sure no
air ventilation slots are blocked.
DO NOT attempt installation and/or operation without knowledge of how to do so.
DO NOT permit operation by persons who are not qualified to operate this type of fixture. Most damages are the result of
operations by nonprofessionals.
Consistent operational breaks may ensure the fixture will function properly for many years to come.
DO NOT shake fixture and avoid brute force when installing and/or operating the fixture.
Always install the fixture with an appropriate safety cable. When installing the fixture in a suspended environment, always use
correct mounting hardware that can be inserted into the Baby 1/8" or Junior 1-1/8" combo pin adapter.
Use the original packaging and materials to transport the fixture in for service.
Fixture Overview (Front)
RBX10
RBX5
Fixture Overview (Back)
RBX5
RBX10
Fixture Menu
ON-BOARD SYSTEM MENU
The fixture comes with an easy to navigate system menu. The next section will detail the functions of each command in the
system menu.
LCD MENU CONTROL KNOB
The control knob allows for local control as well as control from DMX board. The local control gives the user adjustment from
10%-100% in brightness. On Bi-Color fixtures, the local knob gives the user the ability to switch from 5600K-3200K just by
pressing down on the large yellow dial. The user can also adjust the DMX channels 1 thru 512 by pressing down again on the
large yellow dial.
DMX Channel
The DMX512 channel selection can be made from the back of the fixture using the large yellow knob to dial in the correct
DMX number. When a DMX signal is detected on the fixture, all other controls are closed down and only DMX channel control
can be selected on the rear of the fixture.
Depending on the DMX channel selected a bi-color light will require two channels for use on the DMX board.
100% will be the 5600K color output. 0% will be the 3200K color output. The middle position will be 4600K color output.
Example:
Channel
Brightness
5&6
Color
Channel 5
Channel 6
Cleaning & Maintenance
CAUTION!
DISCONNECT POWER BEFORE CLEANING OR MAINTENANCE!
CLEANING
Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. The frequency
of cleaning depends on the environment in which the fixture operates: damp, smoky, or particularly dirty environments can
cause greater accumulation of dirt on the fixture.
Never use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside
this fixture. Please refer all other service issues to an authorized ikan service technician. Should you need any spare parts,
please order genuine parts from your local ikan dealer.
Please refer to the following points during routine inspections:
Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting
in damage or injury as larger parts could fall. Check for any deformations on the housing, rigging hardware and rigging points
(ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging
points or unsecured rigging could cause the fixture to fall and seriously injure a person(s). Electric power supplies and cables
must not show any damage or fraying.
Never remove the ground prong from the power cable.
Specifications
RBX5 Fixture Specifications
RBX10 Fixture Specifications
Light Source
608 0.06 watt LEDs
Light Source
1184 0.06 watt LEDs
Head Type
Bi-Color 5600K-3200K
Head Type
Bi-Color 5600K-3200K
Lens
45°
Lens
45°
Beam Angle
50°
Beam Angle
50°
Control / Dimming
Knob Control
Control / Dimming
Knob Control
Build Material
Heavy Duty Resin Plastic
Build Material
Heavy Duty Resin Plastic
Cooling System
Passive Cooling
Cooling System
Passive Cooling
Yoke
Baby 5/8" -- Junior 1 1/8" Combo Pin
Yoke
Baby 5/8" -- Junior 1 1/8" Combo Pin
Fixture Size
14 x 8 x 3 in.
Fixture Size
14 x 14 x 3 in.
Fixture Weight
4 lbs
Fixture Weight
6 lbs
RBX5 Electrical Specifications
RBX10 Electrical Specifications
Power Supply
Input: 110-220VAC
Output: 15VDC
Power Supply
Input: 110-220VAC
Output: 15VDC
Power Consumption
36.4W; 14-18VDC
Power Consumption
71W; 14-18VDC
Optional Accessories
Some other products that work well with the Rayden DMX Lights available from Ikan include:
CV600
CP-STND-V3
KCP-703
PWRGP-01
ROLLR-STND10
SW-04
IDX-096
Digital LED Light Meter with Exposure & Spectrometer
Compact Light Stand Version 3
Stage Clamp with 16mm Stud
Power Grip
2-Stage Roller Stand 10ft 6in
Safety Wire
96 Channel DMX Console
Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: support@ikancorp.com
Ikan: and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect
economic loss associated with the use or reliance of any information contained within this
document, and/or as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
CONDITIONS OF WARRANTY SERVICE
•
•
Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
The components and maintenance service fee will be charged if the warranty period is expired.
Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)
•
•
Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.
©2017 ikan Corporation. All rights reserved
Download PDF