Pressure and level transmitter PASCAL CV LEVEL,

Pressure and level transmitter PASCAL CV LEVEL,
temperature compensation by LTC-technology,Type series CV311. L
Features
■ Modular pressure and level transmitter temperature
compensation up to 0.1 mbar / 10 K by LTC-technology,
Output signal:
- 4…20 mA, HART®-protocol (rev. 6), option
- PROFIBUS PA
■ Function modules
- Multifunctional display
- Switching module with 2 floating channels
■ Function module replacement on site without
recalibration "plug and measure"
■ Measuring range limits 0…80 mbar to 0…40 bar
■ Accuracy ≤ 0.15 %
■ Turndown 5:1
■ Medium temperature up to 160 °C
■ Various process connections available
■ Mechanically robust stainless steel membrane
Options
■ Approvals/Certificates
- Certificate of measuring equipment for Russian
Federation
- Explosion protection for gases and dust
- Classification per SIL2
- Calibration certificate with 5 measuring points acc. to
EN 10204-3.1
- Material certificate per EN 10204-3.1
Application area
■ Pharmaceutical industry
■ Chemical and petrochemical industry
Application
Pressure transmitter monitoring for vessels and tanks
designed to minimize process temperature errors. The LTCmembrane technology significantly reduces errors that are
related to process temperatures.
Data sheet F2-016 Rev. 1G5
Technical data
Measuring ranges
Nominal range
Turndown
Measuring span 2
Measuring range
min. span
max. span
Overload limit
Vakuum tight
at < 50 °C 1
0.4 bar
-0.4…0.4 bar
80 mbar
0.8 bar
1 bar
400 mbar abs
1 bar
-1…1 bar
0.2 bar
2 bar
3 bar
40 mbar abs
4 bar
-1…4 bar
0.8 bar
5 bar
10 bar
20 mbar abs
16 bar
-1…16 bar
3.2 bar
17 bar
60 bar
20 mbar abs
-1…40 bar
8 bar
41 bar
100 bar
20 mbar abs
100 bar
-1…100 bar
20 bar
101 bar
150 bar
20 mbar abs
4 bar abs
0…4 bar abs
0.8 bar abs
4 bar abs
10 bar abs
20 mbar abs
16 bar abs
0…16 bar abs
3.2 bar abs
16 bar abs
60 bar abs
20 mbar abs
40 bar
5:1
1
Long-term vacuum measurements at temperatures above +50°C may cause changes in the properties of the measurement device. Vacuumproof designs are available upon request.
2
calibrated measuring span for devices with PROFIBUS PA basic module
Constructional design / case
Design:
Construction:
Hygienic case design with screw cap,
material: stainless steel mat.no. 1.4301
(304)
Two-chamber system, minimum housing
volume, excellent moisture and
condensate protection
Measuring system
Sensor:
Piezoresistive measuring element
Sensor filling:
Synthetic oil, free of silicone FD1, FDA
listed, class USDA-H1
Accuracy
Degree of
protection:
IP 66 per EN 60529
General:
Pressure
compensation:
PTFE filter system
Limit point
setting:
per DIN 16086
Window:
Non splintering plastic: Makrolon
Reference
conditions:
per EN 60770-1
Elec.
connection:
Screwed terminals 1 mm²
Linearity
errors:
≤ 0.15 % of span
TD 5:1, no modification
Cable entry
fitting:
Circular connector M12
Hysteresis:
≤ 0.05 % of nominal range
Climatic
category:
EN 60721 3-4, 4K4H
Repeatability:
≤ 0.05 % of nominal range
Vertical mounting position
Weight:
Diaphragm seal with DRD-process
connection and function modules approx.
2.1 kg
Calibration
position:
Influence of
mounting
position
≤ 3.5 mbar
Long-therm
drift:
≤ 0.1 % / year of nonimal range
Temperature
effect:
Case:
Lower range value / upper range value
Range 0…60 °C:
± 0,15 % / 10K of nominal range
Range< 0 °C, > 60 °C:
± 0,2 % / 10K of nominal range
Process connection
Design:
By diaphragm seal, see order code
Material wetted parts
Material:
Stainless steel mat.no. 1.4404 (316L)
Process temperature:
Temperature compensated by LTC
technology
Active membrane
surface
Process
temperature error
ca. Ø 80 mm
< 0.1 mbar/10K
ca. Ø 65 mm
< 0.2 mbar/10K
ca. Ø 50 mm
< 0.4 mbar/10K
Data sheet F2-016 Rev. 1G5
Output
Temperature ranges
General
Ambient:
-20…85 °C
Delay time:
Approx. 160 ms
Medium:
Depending on design, see order code
Measuring cycle:
6 measurements / second
Storage:
-40…85 °C
Measuring range
setting:
Turndown 5:1
Tests and certificates
Basic module: 4…20 mA
Signal:
4…20 mA, 2-wire
Current range:
3.8…20.8 mA
Current limitation:
Approx. 22 mA
Alarm state:
< 3.6 mA, optional > 21 mA
Damping:
0…120 seconds
Load RB:
RB ≤ (UV-12V DC)/22.5mA [Ohm]
UV = supply voltage
Basic module: PROFIBUS PA
Signal:
Digital output signal IEC 61158-2
Protocol:
EN 50170-PROFIBUS PA, Profile 3.0
Sensor address:
0…126 (126 = factor setting)
Power
consumption:
Constantly 11 mA
Fault current IFDE:
2 mA
Damping:
0…300 seconds
Parameterization:
SIMATIC PDM
Interference
emission:
per EN 55011
Noise
immunity:
per EN 61326
Ex-approval:
TÜV 04 ATEX 2387 X
II 1/2G Ex ia IIC T4/T5/T6 (gas)
II 2G Ex ia IIC T4/T5/T6 (gas)
II 2D Ex iaD 21 T 80 °C (dust)
SIL2:
Functional safety:
Classification per SIL2, EN 61508
For basic module 4…20 mA, switching
module, display module and HART
module
TÜV-Reg.-Nr. 44 207 09 555548-001
■ Certificate of measuring equipment for Russian
Federation
Supply voltage
Basic module:
4…20 mA
PROFIBUS PA
12…40 V DC
9…32 V DC
12…30 V DC
-
Standard design:
Functional range:
Ex approval:
Functional range:
Data sheet F2-016 Rev. 1G5
Function modules
Display module (multifunctional display) optional
pluggable with automatic module detection - plug and measure ■ Module housing made of ABS, encapsulated electronics
unit
■ Many operating mode menus
■ 5-segment pressure read-out with unit
■ Read-out display
- pressure (standard)
- percent *
*
- current
- sensor temperature
■ Bar graph 36 segment suitable 0…100 %
■ Measuring circuit test (current sensing function) 3.55…22
mA *
■ Alarm indicator on display
*
■ Switching function indicator
*
not with basic module PROFIBUS PA
Details of the operator menu see parameterisation.
HART® module (for basic module 4…20 mA) optional
■ HART®-protocol, revision 6.5
■ Response characteristic FSK
■ Load with HART® communication
- with Hart® modem 230…500 Ω
- with Hart® communicator 230…1100 Ω
■ Parameterising by
- operating elements
- HART® communication
● PDM 6.0
● AMS
● 375 Field Communicator
Data sheet F2-016 Rev. 1G5
Switch module, (not with basic module PROFIBUS PA) optional
pluggable with automatic module detection - plug and measure -
■ No additional auxiliary power required
■ Module housing made of ABS, encapsulated electronics
unit
■ Electronic switch for 2 limit values, voltage free, shortcircuit-proof
■ Switching capacity 30 V DC / 0.5 A (Ri < 0.3 Ω)
■ Overload indicator: LED red, overload or short-circuit
■ Fusible cut-out at overload / short-circuit with automatic
reset
■ Switch points: 0.0 - 100.0% adjustable, Standard: 50.0%
■ Switching function: maker or breaker, adjustable,
Standard: breaker
■ Device of circuit: contact open
■ Hysteresis: 0.0…100 % adjustable, Standard 0.1 %
- falling or rising, adjustable, standard: falling
■ Switching rate: 6 Hz
■ Electrically isolated to all sides, Insulation voltage: 500 V,
2.5 kV/2 sec.
■ Electrical connection: terminal blocks 1 mm2
Profibus module description and HART® connection upon request
Hysteresis functions
Data sheet F2-016 Rev. 1G5
Parameterisation
The module selected determines which parameters can be set.
Operating modus
Parameter
Basic module: 4…20 mA
display of
display module
Variability
Standard
BM
S
M
A
M
Basic module: PROFIBUS PA
HM
BM
AM
PDM
Zero point *
RANGE/Zero
see instrument ranges
nominal range
x
x
x
x
-
-
x
measuring span *
RANGE/Span
see instrument ranges
nominal range
x
x
x
x
-
-
x
damping
DAMP
4…20 mA:0…120 sec.
Profibus:0…300 sec.
0 sec.
w
-
x
x
-
-
x
Min-max-value
HI/LO
pressure and temperature
resetable
-
-
-
x
x
-
x
x
Characteristic
FUNC
linear, table
linear
w
-
x
x
-
-
x
Pressure unit
UNIT
bar, mbar, kPa, MPa,
mmH2O, mH2O, kg/cm2, PSI
bar
w
-
x
x
-
w
x
Measuring circuit
test
LOOP
3.55…22 mA
-
-
-
x
x
-
-
-
Alarm state
ALARM
< 3.6 mA, > 21 mA
< 3,6 mA
w
-
x
x
-
-
Current trimming
I-CAL
-2…5 %
-
-
-
x
x
-
-
-
Pressure trimming
P-CAL
zero point -50...+50 % of n.r.
span -10...+10 % of n. range
-
-
-
x
x
x
x
x
Table function
TABLE
2…31 points in table
0% = 4mA
100% = 20mA
w
-
x
x
-
-
-
System-Info
INFO
software, serial number,
revision level
-
-
-
x
x
-
x
x
Factory data reset
RESET
-
-
-
-
x
x
-
x
x
BUS address
BUS
0…126
126
-
-
-
-
w
x
x
Switch points
SWCH1(2)
0…100 % v nominal range
50 %
-
x
x
x
-
-
-
Hysteresis
SWCH1(2)/Hyst.
0…100 % v nominal range
0,1 % hyster.
falling
-
w
x
x
-
-
-
Switch function
SWCH1(2)/SwTyp
breaker / maker
breaker
-
w
x
x
-
-
-
HART address
HART/Adres
0…63
0
-
-
x
x
-
-
-
HART current
HART/CUrr
Fixed / Float
Float
-
-
x
x
-
-
-
EIN/AUS
AUS
x
x
x
x
x
x
x
Write protection
-
x = configurable
w = factory setting
* = calibrated measuring span for devices with PROFIBUS PA basic module
AM = display module
BM = basic module
SM = switching module
HM = HART®-module
Connection diagram
Basic module: 4…20mA / PROFIBUS PA
( )
(-)
(+)
n.c.
Switching module: (only with basic module 4…20 mA)
-S2
+S1
+S2
(+) = white
(-) = brown
( ) = green
( )
-S1
(+S2) = yellow
(-S2) = grey
(+S1) = pink
(+)
(-)
(-S1) = blue
Data sheet F2-016 Rev. 1G5
Dimensions
Case
All dimensions are in mm
Process connection
All dimensions are in mm
Data sheet F2-016 Rev. 1G5
Order details
Pressure and level transmitter PASCAL CV LEVEL, temperature compensation by LTC-technology,
Type series CV311. L
Order details PASCAL CV LEVEL
CV311.L
0
Pressure and level transmitter PASCAL CV LEVEL
design
1
standard
Ex-protection, types of ex-protection as follows
A1050
0.4 bar
A1053
1 bar
4 bar
A1056
A1059
nominal range
16 bar
A1061
40 bar
B1056
4 bar abs.
B1059
16 bar abs.
F10
0 to nominal range, unit: bar (Standard)
F11
0 to nominal range, unit: mbar
F22
0 to nominal range, unit: kPa
F23
0 to nominal range, unit: MPa
F30
measuring range
F32
0 to nominal range, unit: mmH2O
0 to nominal range, unit: mH2O
F41
0 to nominal range, unit: kg/cm²
F50
0 to nominal range, unit: PSI
F80
set from... to... unit ( please fill in details ) not with PROFIBUS PA
F81
adjusted and calibrated from ....to...., unit (pls.fill in details), see below for calibration report
H11 . .
4...20 mA, rising characteristic (standard)
H15 . .
20...4 mA, falling characeristic
H21 . .
4...20 mA with HART function module, HART protocol rev. 6
0
1
output signal
damping
setting 1
0
alarm state
1
M2
display module
0
switching module 2
(not with PROFIBUS PA
module)
1
T30
T21
T22
> 21.0 mA
without
multifunctional display with 5-position digital display and bar graph, pluggable
switching module with 2 contacts, pluggable, switching capacity 30 V DC / 0.5 A
standard, s. "Techn. description of switching module"
setting 1
circular connector
T31
T20
< 3.6 mA (standard)
without switching module
N10
N5 .
0.0...120.0 sec..., set to ... (please fill in)
PROFIBUS PA, IEC 61158-2, Profil 3.0
H41
M1
0.0 sec (standard)
at the factory, specify as required
M12 x 1
electrical connection
4pin
8 pin, required for switching module
Polyamid black
cable gland
M16 x 1,5
brass nickel-plated
stainless steel
LABOM Mess- und Regeltechnik GmbH P.O. Box 12 62 27795 Hude Germany Im Gewerbepark 13 27798 Hude Germany
Phone: +49 (0) 4408 804-0 Fax: +49 (0) 4408 804-100 e-mail: info@labom.com www.labom.com
K1085
K2085
measuring device connection
direct mounting
for process temperature up to 125 °C (short term up to 140 °C), standard
for process temperature up to 160 °C (with temperature decoupler)
K3285
angle adapter
DL8140 . . .
tubus-clamp-sterile, DN 85 (Data sheet D5-024-61)
DA1620 . . .
flange type per EN, DN 80, PN 10-40, model B1 (Data sheet D5-030)
DA51510 . . .
flange type per ASME, DN 3", PN 150 psi, B 16.5 RF 500 RMS (Data sheet D5-030)
DL2600 . . .
DL2500 . . .
DL2400 . . .
DL8120 . . .
process connection
(by diaphragm seal)
membrane in
LTC-technology
for process temperature up to 160 °C, adjustable
DN 80 (Data sheet D5-025)
DIN 11851
with union nut
DN 80 (Data sheet D5-025)
DN 80 (Data sheet D5-025)
flange design for sterile application DN 65 (Data sheet D5-024-6)
DD4100 . . .
DRD-connection DN 50/PN 40 (Data sheet D5-024-4)
DL8080 . . .
VARIVENT, D=68 Varivent case DN40...DN125 and 1 1/2"...6" (Data sheet D5-024-1)
DL8110 . . .
NEUMO BioControl, Gr. 65 (Data sheet D5-024-2)
Additional features (to be indicated in case of need, only)
S66
S68
Ex marking 2
...
Z61
Z62
II 1/2G Ex ia IIC T4/T5/T6
II 2G Ex ia IIC T4/T5/T6, II 2D Ex iaD 21 T 80 °C , standard
BUS address
PROFIBUS PA
factory setting: 126 (standard)
factory setting: pls. specify
measuring-point number/identification max. 32 characters, pls. specify
measuring-point text max. 32 characters, pls. specify
Z63
W1020
material certificate as per EN 10204-3.1, wetted parts
W1201
inspection certificate as per EN 10204-3.1, calibration certificate 5 measuring points
W2602
functional safety as per EN 61508, classification per SIL2 3
W2673
certificate of measuring equipment for Russian Federation 4
Accessories
RS 232 interface
MC1020
MC1040
MC1041
HART Modem for
USB interface
USB interface, Ex
Order code (example): CV311 L - A1051 - F11 - H1100 - M2 - N10 - T20 - K1085 - DD4100 . . . - . . .
1
Extensive parameterization is possible when the transmitter is operated with the display module, the HART function module or the PROFIBUS module.
Ex-design not possible with switching module
3
not with PROFIBUS PA
4
not for devices with Ex-protection
2
LABOM Mess- und Regeltechnik GmbH P.O. Box 12 62 27795 Hude Germany Im Gewerbepark 13 27798 Hude Germany
Phone: +49 (0) 4408 804-0 Fax: +49 (0) 4408 804-100 e-mail: info@labom.com www.labom.com
Download PDF

advertising