2016 RAM Commercial ProMaster City 5.0/5.0N Uconnect Radio Book

Uconnect 5.0/5.0 NAV
Owner’s Manual Supplement
16UC5PMC-526-AB
Second Edition Rev 1
Uconnect 5.0/5.0 NAV
Printed in the USA
©2015 FCA US LLC. All Rights Reserved.
Chrysler, Dodge, Jeep, Ram, Mopar and Uconnect are trademarks of FCA US LLC.
FIAT is a registered trademark of FCA Group Marketing S.p.A.,
used under license by FCA US LLC.
SECTION
TABLE OF CONTENTS
PAGE
1
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2
3
ALL ABOUT UCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3
4
RADIO MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4
5
MEDIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5
6
VOICE RECOGNITION QUICK TIPS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6
7
UCONNECT PHONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7
8
MORE BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8
9
NAVIGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9
SAFETY GUIDELINES
CONTENTS
䡵 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . .4 䡵 CYBERSECURITY . . . . . . . . . . . . . . . . . . . . . . . .5
▫ Safe Usage Of The Uconnect System . . . . . . . . . .4
▫ Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1
4 SAFETY GUIDELINES
SAFETY GUIDELINES
WARNING!
ALWAYS drive safely with your hands on the
steering wheel. You have full responsibility and
assume all risks related to the use of the Uconnect
features and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
• Glance at screen only when safe to do so. If prolonged
viewing of the screen is required, park in a safe
location and set the parking brake
• Stop use immediately if a problem occurs. Failure to
do so may cause injury or damage to the product.
Return it to your authorized dealer to repair.
• Ensure the volume level of the system is set to a level
that still allows you to hear outside traffic and emergency vehicles.
Safe Usage Of The Uconnect System
Ensure all persons read this manual carefully before • Read all instructions in this manual carefully before
using the system. It contains instructions on how to use
using your system to ensure proper usage!
the system in a safe and effective manner.
• Your system is a sophisticated electronic device. Do
Please read and follow these safety precautions. Failure
not let young children use your system.
to do so may result in injury or property damage.
SAFETY GUIDELINES 5
• Permanent hearing loss may occur if you play your • Do not spray any liquid or caustic chemicals directly
on the screen! Use a clean and dry micro fiber lens
music or the system at loud volumes. Exercise caution
cleaning cloth in order to clean the touchscreen.
when setting the volume on your system.
• Keep drinks, rain and other sources of moisture away • If necessary, use a lint-free cloth dampened with a
cleaning solution, such as isopropyl alcohol or an
from your system. Besides damage to your system,
isopropyl alcohol and water solution ratio of 50:50. Be
moisture can cause electric shocks as with any elecsure to follow the solvent manufacturer’s precautions
tronic device.
and directions.
NOTE: Many features of this system are speed dependent. For your own safety, it is not possible to use some CYBERSECURITY
of the touchscreen features while the vehicle is in motion.
Your vehicle may be a connected vehicle and may be
Touchscreen
equipped with both wired and wireless networks. These
• Do NOT attach any object to the touchscreen, doing networks allow your vehicle to send and receive information. This information allows systems and features in
so can result in damage to the touchscreen.
your vehicle to function properly.
• Do not press the touchscreen with any hard or sharp
objects (pen, USB stick, jewelry, etc.) which could Your vehicle may be equipped with certain security
features to reduce the risk of unauthorized and unlawful
scratch the touchscreen surface!
access to vehicle systems and wireless communications.
1
6 SAFETY GUIDELINES
Vehicle software technology continues to evolve over
time and FCA US LLC, working with its suppliers,
evaluates and takes appropriate steps as needed. Similar
to a computer or other devices, your vehicle may require
software updates to improve the usability and performance of your systems or to reduce the potential risk of
unauthorized and unlawful access to your vehicle systems.
The risk of unauthorized and unlawful access to your
vehicle systems may still exist, even if the most recent
version of vehicle software (such as Uconnect software) is
installed.
WARNING!
• It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle systems,
including safety related systems, could be impaired or a loss of vehicle control could occur that
may result in an accident involving serious injury
or death.
• ONLY insert media (e.g., USB, SD card, or CD) into
your vehicle if it came from a trusted source. Media
of unknown origin could possibly contain malicious software, and if installed in your vehicle, it
may increase the possibility for vehicle systems to
be breached.
• As always, if you experience unusual vehicle behavior, take your vehicle to your nearest authorized
dealer immediately.
SAFETY GUIDELINES 7
NOTE:
• FCA or your dealer may contact you directly regarding
software updates.
• To help further improve vehicle security and minimize
the potential risk of a security breach, vehicle owners
should:
• Routinely
check
www.driveuconnect.com/software-update
to
learn about available Uconnect software updates.
• Only connect and use trusted media devices (e.g.
personal mobile phones, USBs, CDs).
Privacy of any wireless and wired communications cannot be assured. Third parties may unlawfully intercept
information and private communications without your
consent. For further information, refer to “Onboard Diagnostic System (OBD II) Cybersecurity” in “Maintaining
Your Vehicle” in your Owner’s Manual on the DVD.
1
INTRODUCTION
CONTENTS
䡵 UCONNECT 5.0 SYSTEM . . . . . . . . . . . . . . . . . .10
䡵 UCONNECT 5.0 SYSTEM W/NAVIGATION — IF
EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2
10 INTRODUCTION
UCONNECT 5.0 SYSTEM
INTRODUCTION 11
CAUTION!
Do NOT attach any object to the touchscreen,
doing so can result in breaking the touchscreen.
1 — SCREEN ON/OFF
4 — ENTER/BROWSE & TUNE/SCROLL
Push the ENTER/BROWSE button to accept a highlighted selection on the screen. Rotate the TUNE/
SCROLL rotary knob to scroll through a list, tune a radio
station or skip tracks in Media Mode.
Push the SCREEN ON/OFF button on the faceplate to 5 — MORE
turn the touchscreen ON or OFF.
Push the MORE button on the faceplate to access additional options such as: Trip, Clock and Outside Temp.
2 — SETTINGS
Push the SETTINGS button to access the Uconnect setting 6 — PHONE
features.
Push the PHONE button to access the Uconnect Phone
feature.
3 — BACK
Push the BACK button to return to a previous menu or 7 — COMPASS
screen.
Push the COMPASS button on the faceplate to display
the current direction of the vehicle.
2
12 INTRODUCTION
8 — MEDIA
Pushing the MEDIA button will allow you to switch to
Media mode (USB/iPOD, AUX or Bluetooth.)
9 — RADIO
Push the RADIO button on the faceplate to enter Radio
Mode. The different tuner modes; AM, FM and SXM – If
Equipped can be selected by pushing the corresponding
button on the touchscreen while in the Radio Mode.
10 — ON/VOLUME
Rotate the rotary knob to adjust the Volume. Push the
ON/VOLUME button to turn on the system. Push the
ON/VOLUME button a second time to turn off the
system.
11 — MUTE
Push the MUTE button for activation/deactivation of the
volume.
INTRODUCTION 13
UCONNECT 5.0 SYSTEM W/NAVIGATION — IF EQUIPPED
2
14 INTRODUCTION
CAUTION!
Do NOT attach any object to the touchscreen,
doing so can result in breaking the touchscreen.
1 — SCREEN ON/OFF
4 — ENTER/BROWSE & TUNE/SCROLL
Push the ENTER/BROWSE button to accept a highlighted selection on the screen. Rotate the TUNE/
SCROLL rotary knob to scroll through a list, tune a radio
station or skip tracks in Media Mode.
Push the SCREEN ON/OFF button on the faceplate to 5 — MORE
turn the touchscreen ON or OFF.
Push the MORE button on the faceplate to access additional options such as: Trip, Clock, Outside Temp or
2 — SETTINGS
Compass.
Push the SETTINGS button to access the Uconnect setting
6 — PHONE
features.
Push the PHONE button to access the Uconnect Phone
3 — BACK
feature.
Push the BACK button to return to a previous menu or
7 — NAVIGATION
screen.
Push the NAV button to access the navigation feature.
INTRODUCTION 15
8 — MEDIA
Pushing the MEDIA button will allow you to switch to
Media mode (USB/iPOD, AUX or Bluetooth.)
9 — RADIO
Push the RADIO button on the faceplate to enter Radio
Mode. The different tuner modes; AM, FM and SXM – If
Equipped can be selected by pushing the corresponding
button on the touchscreen while in the Radio Mode.
10 — ON/VOLUME
Rotate the rotary knob to adjust the Volume. Push the
ON/VOLUME button to turn on the system. Push the
ON/VOLUME button a second time to turn off the
system.
11 — MUTE
Push the MUTE button for activation/deactivation of the
volume.
2
ALL ABOUT UCONNECT
CONTENTS
䡵 WHAT IS UCONNECT? . . . . . . . . . . . . . . . . . . .18
䡵 IDENTIFYING YOUR RADIO . . . . . . . . . . . . . . .20
3
18 ALL ABOUT UCONNECT
WHAT IS UCONNECT?
Before you drive, familiarize yourself with the easy-touse Uconnect System.
• The Uconnect Voice Command And Uconnect Phone
Buttons On Your Steering Wheel
• The buttons let you use your voice to give commands,
make phone calls, respond to text messages handsfree, enter navigation destinations and control your
radio and media devices.
1 — Push To
2 — Push To
ceive A Text
3 — Push To
Functions
4 — Push To
MUTE
Initiate Or To Answer A Phone Call, Send Or ReBegin Radio, Media, Navigation, Apps And Climate
End Call
ALL ABOUT UCONNECT 19
3
1
2
3
4
5
6
7
—
—
—
—
—
—
—
Uconnect Phone Hang Up Button
Uconnect Voice Command Button
Uconnect Phone Mute Button
Uconnect Phone Pick Up Button
Volume Knob
Mute Button
Screen On/Off Button
8 — Settings Button
9 — Back Button
10 — Browse/Enter — Tune/Scroll
11 — More Button
12 — Media Button
13 — Audio Jack
14 — USB Port
20 ALL ABOUT UCONNECT
WARNING!
ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume
all risks related to the use of the Uconnect features
and applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
IDENTIFYING YOUR RADIO
There are a few quick ways for you to identify your radio.
For a more complete description, please refer to the User
Guide in your glove box or visit DriveUconnect.com.
Uconnect 5.0/5.0N features:
• 5” Touchscreen
• Hands-free/Bluetooth
• SiriusXM Satellite Radio (If Equipped)
Uconnect 5.0/5.0N
RADIO MODE
CONTENTS
䡵 RADIO MODE. . . . . . . . . . . . . . . . . . . . . . . . . .22
▫ Setting Presets. . . . . . . . . . . . . . . . . . . . . . . . .24
▫ Volume & Mute . . . . . . . . . . . . . . . . . . . . . . .22
▫ SiriusXM Satellite Radio Mode — If Equipped . .25
▫ Enter/Browse & Tune/Scroll Control . . . . . . . .22
▫ SiriusXM Premier . . . . . . . . . . . . . . . . . . . . . .25
▫ Seek Functions . . . . . . . . . . . . . . . . . . . . . . . .22
▫ Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
▫ Direct Tune. . . . . . . . . . . . . . . . . . . . . . . . . . .23
4
22 RADIO MODE
RADIO MODE
Enter/Browse & Tune/Scroll Control
WARNING!
ALWAYS drive safely with your hands on the
steering wheel. You have full responsibility and
assume all risks related to the use of the Uconnect
features and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
Volume & Mute
Turn the rotary TUNE/SCROLL control knob clockwise
to increase or counterclockwise to decrease the radio
station frequency.
Seek Functions
Seek Up
button to tune the
Press and release the “Seek Up”
radio to the next listenable station or channel.
During a Seek Up function, if the radio reaches the
starting station after passing through the entire band two
times, the radio will stop at the station where it began.
Rotate the rotary knob to adjust the Volume. When the
audio system is turned on, the sound will be set at the Fast Seek Up
same volume level as last played.
button to advance the
Press and hold the “Seek Up”
radio
through
the
available
stations
or channels at a
Push the MUTE button to mute the system. Push the
faster
rate,
the
radio
stops
at
the
next
available station
MUTE button again to unmute the system.
or channel when the button is released.
RADIO MODE 23
Seek Down
Direct Tune
button to tune the
Press and release the “Seek Down”
radio to the next listenable station or channel.
During a Seek Down function, if the radio reaches the
starting station after passing through the entire band two
times, the radio will stop at the station where it began.
4
Fast Seek Down
button to advance
Press and hold the “Seek Down”
the radio through the available stations or channel at a
faster rate, the radio stops at the next available station
or channel when the button is released.
The Direct Tune touchscreen is available in AM, FM and
SXM — If Equipped radio modes and can be used to
direct tune the radio to a desired station or channel. Press
the “Tune” button located at the bottom of the radio
screen.
24 RADIO MODE
Press the available number button to begin selecting a Setting Presets
desired station. Once a number has been entered, any
numbers that are no longer possible (stations that cannot
be reached) will become deactivated/grayed out.
If you accidently entered the wrong station number, press
the “CLR” button to clear the radio station numbers and
re-enter the correct station number.
Once the last digit of a station has been entered, the
Direct Tune touchscreen will close and the system will
automatically tune to that station. The selected Station or
Channel number is displayed in the Direct Tune text box.
The Presets are available for all Radio Modes, and are
activated by pressing any of the four “Preset” buttons,
located at the top of the screen.
RADIO MODE 25
music plus sports, news, talk and entertainment. Get all
the premium programming, including Howard Stern,
every NFL game, Oprah Radio, every MLB and NHL
game, every NASCAR race, Martha Stewart and more.
And get 20+ extra channels, including SiriusXM Latino,
The Radio stores up to 12 presets in each of the Radio
offering 20 channels of commercial free music, news, talk,
modes. Four presets are visible at the top of the radio
comedy, sports and more dedicated to Spanish language
screen.
programming.
Pressing the “All” button on the radio home screen will
SiriusXM services require subscriptions, sold separately
display all of the preset stations for that mode.
after the 12-month trial included with the new vehicle
purchase. If you decide to continue your service at the
SiriusXM Satellite Radio Mode — If Equipped
end of your trial subscription, the plan you choose will
SiriusXM Satellite Radio uses direct satellite-to-receiver
automatically renew and bill at then-current rates until
broadcasting technology to provide clear, coast to coast
you call SiriusXM at 1-866-635-2349 to cancel. See
radio content. SiriusXM is a subscription based service.
SiriusXM Customer Agreement for complete terms at
SiriusXM Premier
www.siriusxm.com. All fees and programming subject
to change. Our satellite service is available only to those
Get over 160 channels on your satellite radio, and enjoy
at least 18 and older in the 48 contiguous USA and D.C.
all you want, all in one place. Hear commercial-free
Our Sirius satellite service is also available in PR (with
When you are receiving a station that you wish to
commit into memory, press and hold the desired numbered button for more that two seconds or until you hear
a confirmation beep.
4
26 RADIO MODE
coverage limitations). Our Internet radio service is avail- Audio
able throughout our satellite service area and in AK and
HI. © 2015 SiriusXM Radio Inc. Sirius, XM and all related
marks and logos are trademarks of SiriusXM Radio Inc.
Service available in Canada; see www.siriusxm.ca.
This functionality is only available for radios equipped
with a Satellite receiver. To receive satellite radio, the
vehicle needs to be outside with a clear view to the sky.
If the screen displays Acquiring Signal, you may need to
change the vehicle’s position to receive a signal. In most
cases, the satellite radio does not receive a signal in
underground parking garages or tunnels.
1. Push the SETTINGS button located on the faceplate.
2. Then scroll down and press the “Audio” button located on the touchscreen to open the Audio menu.
3. The Audio Menu displays the following options for
you to customize your audio settings.
RADIO MODE 27
Equalizer
Balance
Press the “Equalizer” button to adjust the Bass, Mid and
Treble. Use the “+” or “–” buttons to adjust the equalizer
to your desired settings. Press the “back arrow” button
when completed.
Press the “Balance” button to adjust the sound from the
speakers. Use the “arrow” button to adjust the sound
level from the front and rear or right and left side
speakers. Press the Center “C” button to reset the balance
and fade to the factory setting. Press the “back arrow”
button when completed.
Speed Adjustable Volume
Press the “Speed Adjusted Volume” button to select
between OFF, 1, 2 or 3. This will increase the radio
volume relative to a increase in vehicle speed. Press the
“back arrow” button when completed.
Loudness
Press the “Loudness” button to select the Loudness
feature. When this feature is activated it improves sound
quality at lower volumes. Press the “back arrow” button
when completed.
4
28 RADIO MODE
Auto On Radio
Press the “Auto On Radio” button to set how the radio
behaves when the Ignition is switched to ON. The
options are: On, Off or Recall Last to the last turned to
stop condition. Press the “back arrow” button when
completed.
MEDIA MODE
CONTENTS
䡵 MEDIA MODE . . . . . . . . . . . . . . . . . . . . . . . . .30
▫ AUX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .32
▫ Common Media Functions . . . . . . . . . . . . . . . .31
▫ Bluetooth Mode . . . . . . . . . . . . . . . . . . . . . . .34
▫ USB/iPod Mode . . . . . . . . . . . . . . . . . . . . . . .32
5
30 MEDIA MODE
MEDIA MODE
WARNING!
ALWAYS drive safely with your hands on the
steering wheel. You have full responsibility and
assume all risks related to the use of the Uconnect
features and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
Media Mode is entered by pushing the MEDIA button
located on the faceplate. Once in MEDIA mode, press the
“Source” button and the desired mode button. USB, AUX
and Bluetooth are the Media sources available. You can
select the “Browse” button to be given these options:
• Now Playing
• Songs
• Artists
• Playlists
• Albums
• Folders
• Genres
You can select the “Source” button, “Pause/Play” button
or the “Info” button for artist information on current
song playing.
MEDIA MODE 31
Common Media Functions
Fast Seek Down
Press and hold the “Seek Down”
button and the
desired mode will begin to rewind through the current
Press and release the “Seek Up”
button for the next
track until the button is released.
butselection. Press and release the “Seek Down”
ton to return to the beginning of the current selection, Source
or return to the beginning of the previous selection if
Press the “Source” button to select the desired audio
the USB, AUX and Bluetooth is within the first three
source, AUX, USB/iPod or Bluetooth. This screen will
seconds of the current selection.
time out after a few seconds and return to the main radio
Fast Seek Up
screen if no selection is made.
Seek Up
/Down
Press and hold the “Seek Up”
button and the desired
mode will begin to fast forward through the current
track until the button is released.
Seek Down
Info
Press the “Info” button to display the current track
information. Press the “X” button to cancel this feature.
Shuffle
button on the
Press and release the “Seek Down”
Press the “Shuffle” button to play the selections on the
touchscreen to tune the radio to the next listenable
USB/iPod or Bluetooth (if supported) device in random
station or channel.
5
32 MEDIA MODE
order to provide an interesting change of pace. Press the Inserting USB/iPod Device
button a second time to turn this feature off.
Gently insert the USB/iPod device into the USB Port. If
you insert a USB/iPod device with the ignition ON, the
Repeat
unit will switch to USB/iPod mode and begin to play
Press the ⬙Repeat⬙ button to replay the selection on the
when you insert the device. The display will show the
USB/iPod or Bluetooth (if supported) device. Press the
Artist and Title name, and index time in minutes and
button a second time to turn this feature off.
seconds.
Audio
Browse
Refer to Operating Instructions – Radio Mode for adjustPress the “Browse” button to select Artist, Albums,
ing the audio settings.
Genres, Songs, Playlists or Folders from the USB device
only. Once the desired selection is made you can choose
USB/iPod Mode
from the available media by pressing the button. Press
USB/iPod Mode is entered by either inserting a USB
the “Exit” button if you want to cancel the browse
Jump Drive or iPod cable into the USB port or by pushing
function.
the MEDIA button located left of the display. Once in
MEDIA mode, press the “Source” button and select AUX Mode
USB/iPod.
AUX Mode is entered by inserting a AUX device using a
cable with a 3.5 mm stereo audio jack into the AUX port
MEDIA MODE 33
or by pushing the MEDIA mode button located below the Inserting Auxiliary Device
display. Once in MEDIA mode, press the “Source” button
Gently insert the Auxiliary device cable into the AUX
and select AUX.
Port. If you insert a Auxiliary device with the ignition
ON, the unit will switch to AUX mode and begin to play
when you insert the device cable.
Controlling The Auxiliary Device
The control of the auxiliary device (e.g., selecting playlists, play, fast forward, etc.) cannot be provided by the
radio; use the device controls instead. Adjust the volume
with the VOLUME rotary knob, or with the volume of the
attached device.
NOTE: The vehicle radio unit is acting as the amplifier
for audio output from the Auxiliary device. Therefore if
the volume control on the Auxiliary device is set too low,
there will be insufficient audio signal for the radio unit to
play the music on the device.
5
34 MEDIA MODE
Bluetooth Mode
Bluetooth Streaming Audio (BTSA) or Bluetooth Mode is
entered by pairing a Bluetooth compatible device containing music, to the Uconnect system.
Before proceeding, the Bluetooth device needs to be
paired through Uconnect Phone to communicate with the
Uconnect System.
NOTE: See the pairing procedure in this manual for
further details.
Once the Bluetooth device is paired to the Uconnect
System, push the MEDIA button. Once in MEDIA mode,
press the “Source” button and select Bluetooth.
VOICE RECOGNITION QUICK TIPS
CONTENTS
䡵 UCONNECT VOICE RECOGNITION . . . . . . . . .36
▫ Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
▫ Introducing Uconnect . . . . . . . . . . . . . . . . . . .36
▫ Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
▫ Get Started . . . . . . . . . . . . . . . . . . . . . . . . . . .37
▫ Voice Text Reply . . . . . . . . . . . . . . . . . . . . . . .42
▫ Basic Voice Commands . . . . . . . . . . . . . . . . . .38
▫ Additional Information . . . . . . . . . . . . . . . . . .43
▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
6
36 VOICE RECOGNITION QUICK TIPS
UCONNECT VOICE RECOGNITION
Key Features:
• 5.0 inch full color touchscreen display
WARNING!
ALWAYS drive safely with your hands on the
steering wheel. You have full responsibility and
assume all risks related to the use of the Uconnect
features and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
Introducing Uconnect
Start using Uconnect Voice Recognition with these helpful quick tips. It provides the key Voice Commands and
tips you need to know to control your Uconnect 5.0
system.
• Bluetooth Connectivity
• Hands Free Uconnect Phone
• Two buttons on either side of the touchscreen display
VOICE RECOGNITION QUICK TIPS
Get Started
1. Visit UconnectPhone.com to check mobile device and
feature compatibility and to find phone pairing instructions.
37
All you need to control your Uconnect system with your
voice are the buttons on your steering wheel.
2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact
recognition.
3. Speak clearly at a normal pace and volume while
facing straight ahead. The microphone is positioned
on the rearview mirror and aimed at the driver.
4. Each time you give a Voice Command, you must first
push either the VR or PHONE button, wait until after
the beep, then say your Voice Command.
1 — Push To MUTE
5. You can interrupt the help message or system prompts 2 — Push To Initiate Or To Answer A Phone Call, Send Or Receive A Text
by pushing the VR or PHONE button and saying a 3 — Push To End Call
Voice Command from current category.
4 — Push To Begin Radio, Media And Navigation Functions
6
38 VOICE RECOGNITION QUICK TIPS
Basic Voice Commands
The basic Voice Commands below can be given at any
point while using your Uconnect system.
Push the VR button
. After the beep, sayѧ
• Cancel to stop a current voice session
• Help to hear a list of suggested Voice Commands
• Repeat to listen to the system prompts again
Notice the visual cues that inform you of your voice
recognition system’s status. Cues appear on the touchscreen.
VOICE RECOGNITION QUICK TIPS
39
Radio
Use your voice to quickly get to the AM, FM or SiriusXM
Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.)
Push the VR button
. After the beep, sayѧ
• Tune to ninety-five-point-five FM
• Tune to Satellite Channel Hits 1
TIP: At any time, if you are not sure of what to say or
want to learn a Voice Command, push the VR button
and say “Help.” The system will provide you with
a list of commands.
6
40 VOICE RECOGNITION QUICK TIPS
TIP: Press the “Browse” button on the touchscreen to see
all of the music on your iPod or USB device. Your Voice
Uconnect offers connections via USB, SD, Bluetooth and
Command must match exactly how the artist, album,
Auxiliary ports (If Equipped). Voice operation is only
song and genre information is displayed.
available for connected USB and iPod devices. (Remote
CD player optional and not available on all vehicles.)
Media
. After the beep, say one of the
Push the VR button
following commands and follow the prompts to
switch your media source or choose an artist.
• Change source to Bluetooth
• Change source to iPod
• Change source to USB
• Play artist Beethoven; Play album Greatest Hits; Play
song Moonlight Sonata; Play genre Classical
VOICE RECOGNITION QUICK TIPS
41
TIP: When providing a Voice Command, push the
PHONE button
and say “Call,” then pronounce the
Making and answering hands-free phone calls is easy
name exactly as it appears in your phone book. When
with Uconnect. When the Phonebook button is illumia contact has multiple phone numbers, you can say
nated on your touchscreen, your system is ready. Check
“Call John Smith work.”
UconnectPhone.com for mobile phone compatibility
and pairing instructions.
Phone
. After the beep, say one of
Push the PHONE button
the following commands:
• Call John Smith
• Dial 123-456-7890 and follow the system prompts
• Redial (call previous outgoing phone number)
• Call back (call previous incoming phone number)
6
42 VOICE RECOGNITION QUICK TIPS
Voice Text Reply
Uconnect will announce incoming text messages. Push
and say Listen. (Must have
the PHONE button
compatible mobile phone paired to Uconnect system.)
1. Once an incoming text message is read to you, push
. After the beep, say... “Rethe PHONE button
ply”
2. Listen to the Uconnect prompts. After the beep, repeat
one of the pre-defined messages and follow the system
prompts.
PRE-DEFINED VOICE TEXT REPLY RESPONSES
Yes.
Stuck in traffic.
See you later.
No.
Start without
I’ll be late.
me.
Okay.
Where are you? I will be <number> minutes
Call me.
Are you there
late.
yet?
I’ll call you
later.
I’m on my way.
I’m lost.
I need directions.
Can’t talk right
now.
See you in
<number> of
minutes.
Thanks.
TIP: Your mobile phone must have the full implementation of the Message Access Profile (MAP) to take advantage of this feature. For details about MAP, visit
UconnectPhone.com. Apple iPhone iOS6 or later supports reading incoming text messages only.
VOICE RECOGNITION QUICK TIPS
Additional Information
43
Uconnect System Support:
© 2015 FCA US LLC. All rights reserved. Mopar and • U.S. residents - visit DriveUconnect.com or call
Uconnect are registered trademarks and Mopar Owner
1-877-855-8400 (24 hours a day 7 days a week)
Connect is a trademark of FCA US LLC. Android is a
• Canadian residents call 1-800-465-2001 (English) or
trademark of Google Inc. SiriusXM and all related marks
1-800-387-9983 (French) or visit DriveUconnect.ca
and logos are trademarks of SiriusXM Radio Inc. Yelp,
Mon. – Fri., 8:00 am – 8:00 pm, ET
Yelp logo, Yelp burst and related marks are registered
trademarks of Yelp.
Sat., 9:00 am – 5:00 pm, ET
Sun., Closed
Uconnect Access Services Support 1-855-792-4241. Please
have your Uconnect Security PIN ready when you call.
6
UCONNECT PHONE
CONTENTS
䡵 UCONNECT PHONE . . . . . . . . . . . . . . . . . . . . .46
▫ Mute (Or Unmute) Microphone During Call . . .50
▫ Pairing A Phone . . . . . . . . . . . . . . . . . . . . . . .47
▫ Transfer Ongoing Call Between Handset And
Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
▫ Start Pairing Procedure . . . . . . . . . . . . . . . . . .47
▫ Phonebook Download — Phonebook Transfer
From Mobile Phone . . . . . . . . . . . . . . . . . . . . .48
▫ SMS Message Reader. . . . . . . . . . . . . . . . . . . .50
▫ SMS Message Reader Activation/Deactivation . .50
▫ Making A Phone Call . . . . . . . . . . . . . . . . . . .49
▫ SMS Message Options . . . . . . . . . . . . . . . . . . .51
▫ Receiving A Call — Accept (And End) . . . . . . .49
▫ Changing The Volume . . . . . . . . . . . . . . . . . . .51
7
46 UCONNECT PHONE
WARNING!
NOTE:
• The Uconnect requires a mobile phone equipped with
the Bluetooth Hands-Free Profile, Version 1.0 or
higher. For Uconnect customer support:
• U.S. residents - visit UconnectPhone.com or call
1-877-855-8400 (24 hours a day 7 days a week)
• Canadian residents - visit UconnectPhone.com or
call 1-800-465-2001 (English) or 1-800-387-9983
(French)
Mon.
– Fri., 8:00 am – 8:00 pm, ET
UCONNECT PHONE
Sat., 9:00 am – 5:00 pm, ET
The Uconnect is a voice-activated, hands-free, in-vehicle
communications system with Voice Command CapabilSun., Closed
ity (see Voice Command section).
• Prior to starting the pairing procedure, ensure all
The Uconnect allows you to dial a phone number with
additional Bluetooth devices or phones within the
your mobile phone using simple voice commands.
vehicle have their Bluetooth disabled.
ALWAYS drive safely with your hands on the
wheel. You have full responsibility and assume all
risks related to the use of the Uconnect features
and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
UCONNECT PHONE 47
6. When prompted by the mobile phone, use its keyboard to enter the PIN code shown on the system
To use the Uconnect feature, you must first pair your
display, or confirm on the mobile phone the PIN
Bluetooth phone with the Uconnect system. Refer to
displayed on the Uconnect system and select “Pair.”
UconnectPhone.com for pairing procedure unique to
• From the mobile phone screen you can always pair a
your phone.
mobile phone by pushing the “Settings” button, then
Start Pairing Procedure
pressing the “Add Device” button and proceeding as
described above.
1. Activate the Bluetooth on your mobile phone.
• During the pairing stage, a screen is displayed
2. Push the “PHONE” button on the radio faceplate.
indicating the progress of the operation.
3. If there are not any mobile phones paired with the 7. If the pairing procedure is completed successfully, a
system, the display shows a dedicated screen asking if
screen is displayed asking if you would like to make
you would like to pair a phone.
this phone a favorite. Press “Yes” to the question to
Pairing A Phone
4. Press the “Yes” button to start the pairing procedure
search for the Uconnect system on the mobile phone
(if No is selected, the Phone main screen is displayed).
5. Select “Uconnect” from the device list on the mobile
phone.
pair the mobile phone as favorite (the mobile phone
will have priority on all other mobile phones that will
be paired later on). If no other devices are paired, the
system will consider the first associated device as
favorite.
7
48 UCONNECT PHONE
NOTE:
Phonebook Download — Phonebook Transfer
From Mobile Phone
• The priority is determined according to the order of
connection for mobile phones which are not set as If equipped and specifically supported by your phone,
favorite. The last phone connected will have the high- Uconnect will ask you if you want to download names
(text names) and number entries from your mobile
est priority.
phone’s phonebook. Press the “book icon” to begin the
• For assistance in pairing your phone, contact Uconnect
phonebook data download process. Specific Bluetooth
customer support:
Phones with Phone Book Access Profile may support this
• U.S. residents - visit UconnectPhone.com for phone feature. See UconnectPhone.com for supported phones.
compatibility, pairing instructions and details or call
Download and update, if supported, begins as soon as
1-877-855-8400
• Canadian residents - visit UconnectPhone.com for the Bluetooth phone connection is made to the Uconnect,
phone compatibility, pairing instructions and details for example, after you start the vehicle.
or call 1-800-465-2001 (English) or 1-800-387-9983 NOTE:
(French)
• A message on the screen may ask for permission to
initiate the phonebook download.
UCONNECT PHONE 49
• A maximum of 2,000 entries per phone will be downloaded and updated every time a phone is connected
to the Uconnect.
• Depending on the maximum number of entries downloaded, there may be a short delay before the latest
downloaded names can be used. Until then, if available, the previously downloaded phonebook is available for use.
the mobile phone. The changes are transferred and
updated to Uconnect Phone on the next phone
connection.
Making A Phone Call
Push the “Phone Pick-up” button
wheel.
on the steering
After the BEEP, say “dial” a number (or “call” a name).
• Only the phonebook of the currently connected mobile Receiving A Call — Accept (And End)
phone is accessible.
When an incoming call rings, or is announced on
• Both the SIM card and the mobile phone’s phonebook Uconnect, push the “Phone Pick-up” button.
is downloaded. SIM card phonebook is not part of the
To end a call, push the “Phone Hang-up” button on the
Mobile phonebook. It is possible that the SIM card
steering wheel or the “Answer” button on the radio
phonebook may not be downloaded depending on the
touchscreen.
mobile phone and the phone’s software.
• This downloaded phonebook cannot be edited or
deleted on the Uconnect. These can only be edited on
7
50 UCONNECT PHONE
Mute (Or Unmute) Microphone During Call
During a call, push the “Voice Command” button
the steering wheel.
on
If this function is not supported by the phone, the
corresponding
button is deactivated (greyed out).
When a text message is received, the display will show a
screen where the options “Listen,” “Call” or “Ignore” can
After the BEEP, say “mute” to mute the microphone (or
be selected.
“mute off” to un-mute the microphone).
button to access the list of SMS messages
Press the
Transfer Ongoing Call Between Handset And
received by the mobile phone (the list displays a maxiVehicle
mum of 60 messages received).
During a call, push the “Voice Command” button.
SMS Message Reader Activation/Deactivation
After the BEEP, say “transfer call.”
The SMS message automatic reading function can be
activated/deactivated by pressing the corresponding
SMS Message Reader
button on the display, which is shown after pressing the
The system can read the messages received by the mobile
phone selection button.
phone.
To use this function the mobile phone must support the
SMS exchange function via Bluetooth.
UCONNECT PHONE 51
NOTE: On some mobile phones, to make the SMS voice
reading function available, the SMS notification option
on the phone must be enabled: this option is usually
available on the phone, in the Bluetooth connections
menu for a device registered as Uconnect. After enabling
this function on the mobile phone, it must be disconnected and reconnected with the system to make it
effective.
Changing The Volume
During a phone call, use the radio VOLUME rotary knob
to adjust the volume to a comfortable level while the
Uconnect system is speaking. Please note the volume
setting for Uconnect is different than the audio system.
SMS Message Options
Pre-set SMS messages are stored in the system and can be
sent to answer a received message or as a new message.
When an SMS is received, the system also allows the
message itself to be forwarded.
7
MORE BUTTON
CONTENTS
䡵 MORE MAIN MENU . . . . . . . . . . . . . . . . . . . . .54
▫ Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
▫ Trip Computer . . . . . . . . . . . . . . . . . . . . . . . .54
▫ Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
8
54 MORE BUTTON
MORE MAIN MENU
Clock
Push the MORE button on the faceplate to display the Show the Clock in full screen mode.
More Main Menu. The More Main Menu contains the
Compass
following options:
Press the “Compass” button to display the compass.
Trip Computer
Press the “Trip” button located on the touchscreen to NOTE: All features listed may not be available on your
vehicle. If there is no GPS signal, the system will enter
display the trip information of the car.
search mode, displaying a specific message.
This function allows you to display the consumption
levels and define two separate trips called Trip A and Trip
B for monitoring the car’s complete journey in a similarly
independent manner.
Both functions can be reset (reset - start of a new journey):
To reset the desired Trip hold down the Trip A or Trip B
buttons.
NAVIGATION
CONTENTS
䡵 NAVIGATION (UCONNECT 5.0N) — IF
EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
▫ Read Me First . . . . . . . . . . . . . . . . . . . . . . . . .56
9
56 NAVIGATION
NAVIGATION (UCONNECT 5.0N) — IF EQUIPPED
WARNING!
• ALWAYS drive safely with your hands on the
steering wheel. You have full responsibility and
assume all risks related to the use of the Uconnect
features and applications in this vehicle. Only use
Uconnect when it is safe to do so. Failure to do so
may result in an accident involving serious injury
or death.
• DO NOT IGNORE TRAFFIC LAWS. If a driving
recommendation contradicts the traffic laws, ALWAYS follow the law! Failure to follow traffic laws
may result in serious injury or death.
Read Me First
Switching On
To switch on navigation, push the “NAV” button.
NAVIGATION 57
Setting Up
Please refer to your dealer for more information on the
content update procedure.
When you first switch on navigation, you have to answer
a few set-up questions. Answer the questions by pressing Safety Settings
the touchscreen.
We recommend using the safety settings to make your
GPS Reception
driving as safe as possible.
When you first start TomTom navigation, the system may
need a few minutes to determine your GPS position and
show your current position on the map. In future, your
position will be found much faster, usually within a few
seconds.
These are some of the options included in the safety
settings:
• Show safety reminders.
• Warn when driving faster than allowed.
Large objects such as tall buildings can sometimes inter- You can also drive more safely by using voice commands
fere with GPS reception.
to control navigation.
The Update Portal
Getting Help To Use Your Navigation System
The Update Portal will be used for updating the content You
can
get
further
help
by
going
uk.support.tomtom.com/app/answers/list.
of your navigation system, such as the map.
to
9
58 NAVIGATION
Planning A Route
To plan a route, do the following:
1. Press the touchscreen to open the Main Menu.
You can change the country or state setting by pressing the state icon in the upper right corner of the
screen.
4. Enter the town or city name, or the ZIP code.
Towns with similar names are shown in the list while
you type.
NOTE: Press the “Arrow” button to the right of the list to
expand the list of suggested towns.
When the correct city or town appears in the list, press
the name to select the destination.
2. Press the “Drive to” button on the touchscreen.
3. Press the “Address” button.
NAVIGATION 59
5. Enter the street name.
6. Enter the house number, then press the “OK” button.
Streets with similar names are shown in the list while
you type.
When the correct street name appears in the list, press
the name to select the destination.
9
60 NAVIGATION
7. The location is shown on the map. Press the “Select”
8. When the new route is shown, press the “Done”
button to continue or press the “Back” button to enter
button.
another address.
For more information about the route, press the “DeNOTE: If you want your final destination to be a parking
tails” buttons.
lot, press the “Parking lot” button and select a location
from the list of parking lots close to your general destination.
NAVIGATION 61
To change your route, for example, to travel via a Safety Mode
particular location or to select a new destination, press
The navigation SW will switch to “Safety Mode,” with a
the “Change route” button.
dedicated menu structure, when driving above a threshold speed of 5 mph (8.0 kph). In this mode, only that
functionality is available that can be used safely when
driving. The main menu in Safety mode is displayed.
You are guided to your destination using spoken
instructions and on-screen directions.
9
62 NAVIGATION
In Safety mode, you can enter a destination (without the Route Summary
use of typewriter, see below), go into map display, and
The route summary shows an overview of your route, the
toggle three settings. The “Navigate to” submenu in
remaining distance to your destination and the remainSafety Mode has reduced functionality:
ing estimated journey time.
To view the route summary, push the right-hand panel on
the status bar in the Driving view or press the “View
route” button in the Main Menu and then press the
“Show route summary” button.
In Safety Mode, it is only possible to enter destinations
that do not require the use of the typewriter.
NAVIGATION 63
Selecting A Route Type
The types of route you can choose from are as follows:
Every time you plan a route, you can choose to be asked • Every Time I Plan — Will ask you the type of route
about the type of route you want to plan.
you want to plan.
To do this, push the “Settings” button followed by the • Fastest Route — Route which takes the least time.
“Route planning,” then “Route types.” Press “Ask me
• Eco route — Most fuel-efficient route for your journey.
every time I plan.”
9
64 NAVIGATION
• Shortest route — Shortest distance between the loca- After entering a destination, press the “YES” button
tions you set. This may not be the quickest route, when asked about an arrival time to enter a preferred
especially if the shortest route is through a town or arrival time.
city.
The navigation system calculates your arrival time and
• Avoid motorways — Route which avoids motorways. shows you whether you will arrive on time.
You can also use this information to work out when you
need to leave. If route planning shows that you will
arrive 30 minutes early, you can wait and leave in 30
You can set your navigation system to ask you if you
minutes time, rather than arrive early.
need to arrive at a particular time when you plan a route.
Your arrival time is constantly recalculated during your
Push the “Status bar” button in the
journey. The status bar shows whether you will arrive on
Settings menu, to enable or disable
time or if you are going to be late, as shown below:
arrival time notifications.
Using Arrival Times
Select how the status bar should be
displayed, then press next.
To enable arrival time notifications,
select “Leeway,” then press “Done.”
NAVIGATION 65
You will arrive 55 minutes before the arrival time you entered.
If the estimated arrival time is more than five minutes before the time you entered, it is
shown in green.
You will arrive 3 minutes before the arrival time you entered.
If the estimated arrival time is less than 5 minutes before the time you entered, it is shown
in yellow.
You will arrive 19 minutes late. If the estimated arrival time is later than the time you
entered, it is shown in red.
9
66 NAVIGATION
Navigation Menu Options
When you press the “Drive to” button you can set your
destination in many ways, not just by entering the
address. The other options are listed below:
Home
Press this button to navigate to your Home location.
You will probably use this button more than any other.
Favorites
Press this button to select a Favorite as your destination.
NAVIGATION 67
Address
Press this button to enter an address as your destination.
Recent Destination
Press this button to select your destination from a list of places you have recently used as
destinations.
9
68 NAVIGATION
Point Of Interest
Press this button to navigate to a Point of Interest (POI).
Latitude Longitude
Press this button to enter a destination using latitude and longitude values.
NAVIGATION 69
Position Of Last Stop
Press this button to select your last recorded position as your destination.
Planning A Route In Advance
week. Navigation uses IQ Routes when planning a
route. IQ Routes calculates routes based on the real
average speeds measured on roads.
You can use your navigation system to plan a route in
advance, selecting your starting point and your destination.
• Study the route of a journey you are planning.
Here are more reasons to plan a route in advance:
• Check a route for someone who is coming to visit you
and then explain the route to them in detail.
• Find out how long a journey is going to take before
you start.
To plan a route in advance, follow these steps:
• You can also compare journey times for the same route 1. Press the touchscreen to bring up the Main menu.
at different times of the day or on different days of the
9
70 NAVIGATION
6. Choose the date and time that you will make the
journey you are planning.
This button is shown when no route
Navigation uses IQ Routes to work out the best
has been planned.
possible route at that time. This is useful to see how
3. Select the starting point for your
long a journey takes at different times of the day or on
journey in the same way that you
different days of the week.
would select your destination.
Your navigation system plans the route between the
4. Set the destination for your journey.
two locations you selected.
5. If Route planning settings are set to “Ask me every Viewing Route Information
time I plan”, select the type of route you want to plan:
You can access these options for the route you last
• Fastest route — Route which takes the least time.
planned by pressing the “View route” button in the Main
• Eco route — Most fuel-efficient route for your journey.
Menu or the “Details” button on the route summary
• Shortest route — Shortest distance between the screen.
locations you set. This may not be the quickest route,
especially if the shortest route is through a town or
city.
• Avoid motorways — Route which avoids motorways.
2. Press the “Plan route” button.
NAVIGATION 71
You can then select from the following options:
Show Instructions
Press this button for a list of all the turn instructions on the route.
This is very useful if you need to explain a route to someone else.
Show Map Of Route
Press this button to see an overview of the route using the map browser.
9
72 NAVIGATION
Show Route Demo
Press this button to watch a demo of the journey.
You can interrupt the demo at any time by pressing the screen.
Show Route Summary
Press this button to open the route summary screen.
NAVIGATION 73
Show Destination
Press this button to see a preview of your destination.
You can navigate to a parking lot near your destination, and view any available information
about your destination, for example, the phone number.
Voice Control
Using Voice Control
About Voice control
Instead of pressing the touchscreen to control your
navigation system, you can use your voice to control
navigation.
For example, to switch to 2D view, you can say “2D
view.”
To view a list of available commands, press the “Help”
button in the Main menu and then press “What can I
say?”
WARNING!
Any voice commanded system should be used
only in safe driving conditions following all
applicable laws. Your attention should be focused
on safely operating the vehicle. Failure to do so
may result in a collision causing serious injury or
death.
9
74 NAVIGATION
The following example shows how to use voice control to 3. If the command is correct, say “Yes.”
plan a journey to your Home address:
If the command is incorrect, say “No” and repeat the
command after you hear the prompt and tone again.
1. Push the “Voice Recognition” button on the steering
wheel to turn on the microphone.
Your navigation system plans a route from your
current location to your destination.
You see a screen with examples of commands you can say.
NOTE: To stop your navigation system from listening
NOTE: Press the “Help” button in the Main out for further commands, say “Cancel.”
menu then press “What can I say?” to see a full list of
commands you can say.
2. When you hear a beep, say a command of your choice.
For example, you can say “Navigate home.”
For some phrases, you are asked for confirmation.
NOTE: For the best recognition of what you say, speak
normally without trying to articulate words in an unnatural way. If there is excessive road noise, for example,
you may need to speak in the direction of the microphone.
NAVIGATION 75
The Driving View
Press the center of the touchscreen, at any time, to open
the Main Menu.
The Driving View
About The Driving View
When your TomTom navigation system starts for the first 1. Zoom button
time, you are shown the Driving View along with dePress the magnifying glass to show buttons for zoomtailed information about your current position.
ing in and out.
9
76 NAVIGATION
2. Your current position
3. Road sign information or the next street name
7. Navigation instruction for the road ahead and the
distance to next instruction
4. Remaining journey time, the remaining distance and
your estimated arrival time
If the second instruction is less than 150m after the
first instruction, you see it shown immediately instead
of the distance.
Press this part of the status bar to open the Route
Summary screen.
Press this part of the status bar to repeat the last voice
instruction.
To change the information shown in the status bar,
Driving View Symbols
press the “Status bar” button in the Settings menu.
Navigation instructions muted
5. Speed limit, if known
This symbol is shown when the navigation
To see the difference between your preferred arrival
instructions have been muted.
time and your estimated arrival time, check the Leeway checkbox in the Status bar settings.
Press this part of the status bar to switch between a 3D
map and a 2D map.
6. Name of the street you are on
To hear navigation instructions again, push the middle
panel in the status bar.
NAVIGATION 77
Advanced Lane Guidance
Using Lane Guidance
About Lane Guidance
There are two types of lane guidance:
NOTE: Lane guidance is not available for all junctions or 1. Lane images
in all countries.
Your navigation system helps you prepare for motorway
exits and junctions by showing the correct driving lane
for your planned route.
As you approach an exit or junction, the lane you need is
shown on the screen.
To turn lane images off, push the “Settings” button in
the Main menu, then press “Advanced settings.” Clear
the checkbox for Show lane images.
9
78 NAVIGATION
NOTE: Press anywhere on the touchscreen to return to NOTE: If no lane guidance is shown in the status bar and
the Driving View.
all lanes are highlighted, you can use any lane.
2. Instructions in the status bar
Changing Your Route
Making Changes To Your Route
After you plan a route, you may want to change the route
or even the destination. There are various ways to change
your route without the need to completely replan the
entire journey.
To change the current route, press the “Change route”
button in the Main menu:
NAVIGATION 79
Change Route
Press this button to change the current route.
This button is only shown while there is a planned route.
Change Route Menu
To change the current route or your destination, press one
of the following buttons:
Change Destination
Press this button to change the current destination.
When you change the destination, you are shown the same options and asked to enter the
new address in the same way as when you plan a new route.
9
80 NAVIGATION
Avoid Roadblock
Press this button while driving on a planned route, to avoid a roadblock or traffic congestion
on the road ahead.
Your navigation system will suggest a new route which avoids the roads on your current
route for the selected distance.
Calculate Alternative
Press this button to find an alternative to the current route.
This button is only shown while there is a planned route.
This is a simple way to search for a different route to your current destination.
Your navigation system calculates a new route from your current location, to reach your
destination using completely different roads.
The new route is shown next to the original route so that you can select the route you want
to use.
NAVIGATION 81
Travel Via
Press this button to change your route by selecting a location you want to travel past, maybe
so you can meet someone on the way.
When you select a location to travel past, you are shown the same options and asked to enter
the new address in the same way as when you plan a new route.
Your navigation system calculates the route to your destination via the selected location.
The selected location is shown on the map using a marker.
You receive a warning when you reach your destination and when you travel past a marked
location.
Avoid Part Of Route
Press this button to avoid part of the current route.
You are shown a list of the street names on your route.
When you press one of the street names, your navigation system calculates a detour to avoid
the selected street.
The route summary shows both the new route and your original route.
Press the panel on the right to select one of the routes and then press “Done.”
If you do not want to use either of the routes shown in the route summary, press “Change
route” to find another way to change your route.
9
82 NAVIGATION
CAUTION!
When a new route is calculated, you may be asked
to turn off the current road.
About Waypoints
Adding The First Waypoint To Your Route
To add the first waypoint to your route, do the following:
1. Press the touchscreen to bring up the Main menu.
2. Press the “Change route” button.
You can choose to use waypoints for any of the following 3. Press the “Travel via” button.
reasons:
NOTE: You can also use Voice control to add Waypoints.
• You want to travel along a certain road or through a 4. Choose the location for your waypoint from a choice
certain area on the way to your destination.
of Home, Favorite, Address, Recent destination, POI,
longitude/latitude, or position of last stop.
• You want to make stops before reaching your final
destination.
On the route summary screen, a message confirms that
the route is being recalculated to include the waypoint. In the Change route menu, the Travel via button
changes to show that you now have one waypoint on
your current route.
When you enter a city center as a waypoint, the route
planner will plan a route via the area around this city, not
via the location of the city center. The route planner may
fail to find a route via a city center that has an awkward
NOTE: The maximum number of waypoints you can add
location w.r.t. the current route.
is three.
NAVIGATION 83
Adding Further Waypoints To Your Route
To add more waypoints to your route after the first one
has been added, do the following:
1. Press the touchscreen to bring up the Main menu.
2. Press the “Change route” button.
3. Press the “Travel via” button.
NOTE: You can also use Voice control to add waypoints.
4. Press the “Add” button.
6. Press the “Done” button.
On the route summary screen, a message confirms that
the route is being recalculated to include your waypoints.
7. Repeat to add more waypoints.
On the Change route menu, the Travel via button
changes to show that you now have several Waypoints
on your current route.
Changing The Order Of Waypoints
5. Choose the location for your waypoint from a choice Waypoints are automatically added in an optimized
of Home, Favorite, Address, Recent destination, POI, order but you can still change the order manually if you
need to. To change the order of waypoints, do the
latitude/longitude or position of last stop.
following:
A message tells you where in the list of waypoints the
1. Press the touchscreen to bring up the Main menu.
new one has been inserted.
2. Press the “Change route” button.
3. Press the “Travel via” button.
9
84 NAVIGATION
4. Press the waypoint you want to move up or down.
You will see a touchscreen with the name of your
waypoint at the top.
You will see a touchscreen with the name of your
waypoint at the top.
5. Press the “Delete” button.
5. Press the “Move up” or “Move down” buttons.
Your waypoint is deleted and you are immediately
returned to your list of waypoints.
Your Waypoint changes its position in the list and you
are immediately returned to your list of waypoints.
Reactivating A Waypoint
NOTE: You cannot move an unvisited waypoint into a NOTE: You can only reactivate a waypoint that has
list of already visited waypoints.
already been visited. Visited waypoints are greyed out.
Deleting A Waypoint
To reactivate a waypoint, do the following:
To delete a waypoint, do the following:
1. Press the touchscreen to bring up the Main menu.
1. Press the touchscreen to bring up the Main Menu.
2. Press the “Change route” button.
2. Press the “Change route” button.
3. Press the “Travel via” button.
3. Press the “Travel via” button.
4. Press the visited waypoint that you want to reactivate.
4. Press the waypoint you want to delete.
You will see a touchscreen with the name of your
waypoint at the top.
NAVIGATION 85
5. Press the “Reactivate” button.
View Map
The waypoint is deleted and reinserted into the list of
waypoints that haven’t yet been visited.
View Map
About Viewing The Map
You can view the map in the same way as you might look
at a traditional paper map. The map shows your current
location and many other locations such as Favorites and
POIs.
To view the map in this way, press “View map” or “View
route”, then “Show map of route” in the Main menu.
You view different locations on the map by moving the
map across the screen. To move the map, press the
touchscreen and drag your finger across the screen.
1. Options button
Press this button to show options on the maps such as
Points of Interest (POIs), favorites, or names.
9
86 NAVIGATION
2. Find button
Sounds And Voices
Press this button to find specific addresses, favorites or About Sounds And Voices
Points of Interest.
Your TomTom navigation system uses sound for some or
3. Zoom bar
all of the following:
Zoom in and out by moving the slider.
• Driving directions
Options
• Warnings that you set
Press the “Options” button to set the information shown There are two types of voice available when navigating:
on the map and show the following information:
1. Computer voices — Computer voices are generated
• Names — Select this option to show street and city
by your navigation system. They read traffic and voice
names on the map.
command responses.
• Points of interest — Select this option to show POIs on 2. Human voices — These are recorded by an actor and
the map. Press “Choose POIs” to choose which POI
only provide route instructions.
categories are shown on the map.
Changing The Volume Level
• Favorites — Select this option to show your Favorites
You can change the volume for your navigation system
on the map.
on the main unit.
NAVIGATION 87
You can turn navigation instructions on/off by doing the Settings
following:
About Settings
• In the Driving view — Press the central panel on the
You can change the way your navigation system looks
status bar to hear navigation instructions again, if they
and behaves. Most of the settings on your system can be
were previously muted.
accessed by pressing the “Settings” button in the Main
• In the Settings menu — Press the “Settings” button in Menu.
the Main menu, then press “Turn on/off voice guidance.”
Use Night Colors
Press this button to display the map in darker colors.
NOTE: Your navigation system can switch between day and night colors depending on
the time of day. To automatically switch between night and day colors, press the “Map
colors” button in the Settings menu and select “Switch to night colors when dark.”
9
88 NAVIGATION
Use Day Colors
Press this button to display the map in brighter colors.
Turn Off Voice Guidance
Press this button to switch off voice guidance. You will no longer hear spoken route
instructions but you will still hear information such as traffic information and warnings.
Voice guidance is also switched off when the main unit volume is muted.
NAVIGATION 89
Turn On Voice Guidance
Press this button to switch on voice guidance and hear spoken route instructions.
Voice Settings
Press this button to set the type of spoken directions and other route instructions that your
navigation system will read aloud.
9
90 NAVIGATION
Make Your Own Menu
Press this button to add up to six buttons to your own personalized menu.
If there are only one or two buttons in your menu, both buttons are shown in the Driving
view.
If you have three or more buttons in your menu, then a single button is shown in the Driving
view which opens your menu when pressed.
Favorites
Press this button to add, rename or delete Favorites.
Favorites provide an easy way to select a location without the need to enter the address.
They do not need to be favorite places, they can simply be seen as a collection of useful
addresses.
To create a new Favorite, press the “Add” button then
enter the location address in the same way that you enter
an address when you plan a route.
NAVIGATION 91
To view or change an existing Favorite, press one of the
items in the list. To see more Favorites on the map, press
the “left or right” buttons.
9
92 NAVIGATION
Home Location
Press this button to set or change your Home location. You enter the address in the same way
as you do when you plan a route.
Your Home location provides an easy way to plan a route to an important location.
For most people, your Home location will be your home address. However, you might prefer
to set the location to another regular destination, such as your workplace.
Route Planning
Press the “Route planning” button to set the way your navigation system calculates the
routes that you plan.
Press the button for each option to change the settings.
NAVIGATION 93
travel on these lanes, you may need to have more than
one person in the vehicle, for example, or the vehicle may
Set the type of route you want your navigation system to
need to use environmentally-friendly fuel.
calculate.
Route Summary
Toll roads, Ferries, Carpool lanes and Unpaved roads
settings
Set whether you want the route summary screen to close
automatically after you plan a route. If you select No,
Set how your navigation system should manage each of
then you will need to press Done to close the route
these road features when the system calculates a route.
summary screen every time you plan a route.
Carpool lanes are sometimes known as High Occupancy
Vehicle Lanes and are not present in every country. To
Route Types
Vehicle Symbol
Press this button to select the vehicle symbol that shows your current location in the driving
view.
9
94 NAVIGATION
Status Bar
Press this button to select the information you want to see on the status bar:
• Horizontal — Show the status bar at the bottom of the Driving view.
• Vertical — Show the status bar on the right-hand side of the Driving view.
• Maximum speed
• Remaining distance — The distance to your destination.
• Leeway — Tour navigation system shows how late or early you will arrive, compared with your preferred arrival time that was set when you planned the route.
CAUTION!
• The speed limit is shown next to your current
speed. If you drive faster than the speed limit your
speed is shown in red.
• Information about speed limits is not available for
all roads.
NAVIGATION 95
Safety Settings
Press this button to select the safety features you want applied to your navigation.
Map Colors
Press this button to select the color schemes for day and night map colors for 2D and 3D
mode.
Press the “Search” button to search for a color scheme by typing the name.
9
96 NAVIGATION
2D/3D Settings
Press this button to set the default view of the map. To switch between 2D and 3D views
while driving, press the left side of the status bar in Driving View.
It is sometimes easier to view the map from above, such as when navigating a complex road
network.
The 2D view shows a two dimensional view of the map as though viewed from above.
The 3D view shows a three dimensional view of the map as though you are driving through
the landscape.
The following buttons are available:
• In 2D view: rotate map in direction of travel — Press this button so the map is
rotated automatically with the direction you are travelling always at the top.
• Switch to 3D view when following a route — Press this button to show the map
automatically in 3D view when you are following a route.
NAVIGATION 97
Switch Map
Press this button to select the map you want to use for route planning and navigation.
Although you can store more than one map on the navigation system, you can only use one
map at a time for planning and navigation.
To switch from the current map to plan a route in another country or region, simply press this
button.
Show POI On Map
Press this button to select the types of Point of Interest (POI) you want to see on the map.
Press the “Show POI” button on the map in the Settings menu.
Select the POI categories you want to be shown on the map.
Press “Search” button and use the keyboard to search for a category name.
Select whether you want POIs to be shown in 2D or 3D views of the map.
Press the “Done” button.
Point of Interest locations are shown on the map as symbols.
9
98 NAVIGATION
Manage POIs
Press this button to manage your own Point of Interest (POI) categories and locations.
You can set your navigation system to let you know when you are near to selected POI
locations. For example, you could set the navigation system to let you know when you are
approaching a gas station.
You can create your own POI categories and add your own POI locations to these categories.
You can, for example, create a new POI category called Friends. You could then add all your
friends’ addresses as POIs in this new category.
Press the following buttons to create and maintain your own POIs:
• Add POI — Press this button to add a location to one of your own POI categories.
• Warn when near POI — Press this button to set your system to warn you when
you are near selected POIs.
• Delete POI — Press this button to delete a POI.
• Add POI category — Press this button to create a new POI category.
• Delete POI category — Press this button to delete one of your own POI categories.
NAVIGATION 99
Units
Press this button to set the units used for navigation features such as route planning.
Keyboard
Press this button to select the keyboards that will be available for your use and the layout of
the Latin keyboard.
You use the keyboard to enter names and addresses, such as when you plan a route or search
for the name of a town or a local restaurant.
9
100 NAVIGATION
GPS Status
Press this button to see the current status of GPS reception on your navigation system.
NAVIGATION 101
Advanced Settings
Press this button to select the following advanced settings:
• Show house number before street name — When this setting is selected, addresses are shown with the house number followed by the street name, such as 10
Downing Street.
• Show street names — When this setting is selected, street names are shown on the
map in the Driving View.
• Show next street name — When this setting is selected, the name of the next
street on your route is shown at the top of the Driving view.
• Show current street name on map — When this setting is selected, the name of
the street you are on is shown at the bottom of the Driving view.
• Show location preview — When this setting is selected, a graphical preview of
your destination is shown during route planning.
• Enable automatic zooming in 2D view
• Enable automatic zooming in 3D view
9
102 NAVIGATION
Advanced Settings
Press this button to select the following advanced settings:
• Show lane images — When this setting is selected, a graphical view of the road
ahead shows which lane you need when you approach a junction or motorway
exit. This feature is not available for all roads.
• Show tips — This setting switches tips on and off.
Me And My Navigation
Press this button to find technical information about your navigation system and to select
whether you want to share information with TomTom.
A menu opens with the following options:
NAVIGATION 103
Reset Factory Settings
Press this button to delete all your personal navigation settings and restore the standard
factory settings to your navigation system.
This is not a software update and will not affect the version of the software application
installed on your system.
This feature deletes all your personal settings! — If you want to keep your personal
information and settings, you should perform a full back up before you reset the navigation
system. You can then restore all your personal information and settings after the reset. This
includes items such as your Home and Favorite locations, your personal menu and your POI
categories and POI locations.
Start-Up
Press this button to change whether or not the consent info question should be asked at every
start-up.
9
104 NAVIGATION
Navigation Updates
The Navigation maps can be updated
using a USB device to download the
most recent maps. To prepare a USB
device to update a map follow the
steps below:
5. Remove the USB device and connect it to a computer.
An updated map can now be downloaded to the USB
device using the TomToM HOME application on the
computer. Refer to www.tomtom.cpm/getstarted to
download the TomTom HOME application.
NOTE: To update the map, a USB device that meets the
1. Ensure that the map you are updat- following requirements must be used:
ing is active in the Navigation sys• 8 GB of free memory
tem.
• Use a FAT-32 file system
2. Select Navigation Updates in the Settings menu.
• The USB device must not be blocked and allow files to
3. Select “Yes” when asked to prepare a USB device for
be saved
downloading updates.
Points Of Interest
4. Insert a USB device (meeting the requirements shown
About Points Of Interest
in the note below).
NOTE: When the USB device is ready a message will be Points of Interest or POIs are useful places on the map.
displayed that it is safe to remove the USB device.
NAVIGATION 105
Here are some examples:
• Restaurants
• Hotels
• Museums
• Parking lots
• Gas stations
Creating POIs
1. Press the touchscreen to open the Main menu.
2. Press the “Settings” button.
3. Press the “Manage POIs” button.
4. If there are no POI categories or the one you want to
use does not exist, Press the “Add POI” category and
create a new category.
Every POI must be assigned to a
POI category. This means you need
to have created at least one POI
category before you can create your
first POI.
You can only add POIs to POI categories you have created.
For more information on creating POI categories, read
“Managing POIs.”
5. Press the “Add POI” button.
6. Select the POI category you want to use for the new
POI.
7. Press a button to enter the POI address in the same
way that you plan a route.
9
106 NAVIGATION
8. The POI is created and saved in the selected category. NOTE: If you already know the name of the POI you
want to use, you can press the “Search by name” button
Using POIs To Plan Route
to enter the name and select this location.
When you plan a route, you can use a POI for the
6. Scroll down the list and press the “Parking lot” button.
destination or as a waypoint.
7. The parking lot closest to the city center is shown at
The following example shows how to plan a route to a
the top of the list.
parking lot in a city:
8. The following list explains the distances shown next to
1. Press the “Drive to” button.
each POI. How the distance is measured varies de2. Press the “Point of Interest” button.
pending on how you initially searched for the POI:
•
POI near you — Distance from your current location.
3. Press the “POI in city” button.
• POI in city — Distance from the city center.
NOTE: The last POI you viewed on your navigation
• POI near Home — Distance from your Home location.
system is also shown in the menu.
• POI along route — Distance from your current
4. Enter the name of the town or city and select it when
location.
it is shown in the list.
• POI near destination — Distance from your destination.
5. Press the arrow button to expand the list of POI
categories.
NAVIGATION 107
9. Press the name of the parking lot you want to use and The types of POI you have selected are shown as symbols
press the “Done” button when the route has been on the map.
calculated.
Setting Warnings For POIs
Your navigation system starts to guide you to the
You can set a warning sound to be played when you
parking lot.
approach a selected type of POI, such as a gas station.
Showing POIs On The Map
The following example will show how to set a warning
You can select the types of POI locations you want to see sound to be played when you are 500 yards from a gas
on your maps.
station.
1. Press the “Show POI on map” button in the Settings 1. Press the “Manage POIs” button and then Warn when
menu.
near POI in the Settings menu.
2. Select the categories you want to be shown on the 2. Scroll down the list and press the “Gas station” button.
map.
NOTE: To remove a warning, press on the category name
3. Press the “Done” button.
and then press the “Yes” button. POI categories which
4. Select whether you want to see POI locations in 2D have been set with a warning have a sound symbol next
to the category name.
and 3D views of the map.
5. Press the “Done” button.
9
108 NAVIGATION
3. Set the distance as 500 yards and press the “OK” Manage POIs
button.
Press the “Manage POIs” button to manage your POI
4. Press the “Sound effect” button and then press the categories and locations.
“Next” button.
You can set your navigation system to
5. Select the warning sound for the POI and then press
let you know when you are near to
selected POI locations. In this way you
the “Next” button.
could, for example, set the navigation
6. If you only want to hear the warning when the POI is
system to let you know when you are
directly on a planned route, select “Warn only if POI is
approaching a gas station.
on route”. Then press the “Done” button.
The warning is set for the selected POI category. You You can create your own POI categories and add your
will hear a warning sound when you are 500 yards own POI locations to these categories.
from a gas station on your route.
This means you can, for example, create a new POI
category called Friends. You could then add all your
friends’ addresses as POIs in this new category.
Press the following buttons to create and maintain your
own POIs:
NAVIGATION 109
• Add POI — Press this button to add a location to one Help
of your own POI categories.
About Getting Help
• Warn when near POI — Press this button to set your
Press the “Help” button in the Main menu to navigate to
system to warn you when you are near selected POIs.
emergency services centers and other specialist services.
• Delete POI — Press this button to delete one of your
For example, if you are involved in a vehicle accident,
own POI categories.
you could use the Help menu to find the contact details
• Edit POI — Press this button to edit one of your own for the nearest hospital, call them using a phone and tell
them your exact location.
POIs.
• Add POI category — Press this button to create a new Using Help To Phone A Local Service
POI category.
To use Help to locate a service center, contact the center
• Delete POI category — Press this button to delete one by phone and navigate from your current location to the
center, do the following:
of your own POI categories.
1. Press the screen to show the Main Menu.
2. Press the “Help” button.
3. Press the “Call for help” button.
9
110 NAVIGATION
4. Select the type of service you require, for example, 6. To navigate your way to the center by vehicle, press
Nearest hospital.
the “Navigate there” button.
5. Select a center from the list, the nearest is shown at the
top of the list.
Your navigation system starts guiding you to your
destination.
Your navigation system shows your position on the Help Menu Options
map along with a description of the location. This
NOTE: In some countries, information may not be availhelps you explain where you are while making a call.
able for all services.
The phone number is displayed for you to call using a
phone.
Call For Help
Press this button to find the contact details and location of a service center.
NAVIGATION 111
Drive To Help
Press this button to plan a driving route to a service center.
Where Am I
Press this button to see your current location on the map.
9
112 NAVIGATION
What Can I Say
Press this button to see a list of commands you can say when using voice control.
Guided Tours
Press this button to view a selection of guided tours relating to your navigation system.
NAVIGATION 113
Safety And Other Guides
Press this button to read a selection of guides, including a First Aid guide.
Favorites
1. Press the touchscreen to bring up the Main menu.
About Favorites
2. Press the “Drive to” button.
Favorites provide an easy way to select a location with- 3. Press the “Favorite” button.
out the need to enter the address. They do not need to be
4. Select a Favorite from the list.
favorite places, they can simply be seen as a collection of
Your navigation system calculates the route for you.
useful addresses.
Using A Favorite
5. When the route is calculated, press the “Done” button.
You can use a Favorite as a way of navigating to a place Your navigation system immediately starts guiding you
without having to enter the address. To navigate to a to your destination with spoken instructions and visual
instructions on the touchscreen.
Favorite, do the following:
9
114 NAVIGATION
Changing The Name Of A Favorite
Deleting A Favorite
To change the name of a Favorite, do the following:
To delete a Favorite, do the following:
1. Press the touchscreen to bring up the Main menu.
1. Press the touchscreen to bring up the Main menu.
2. Press the “Settings” button to open the Settings menu. 2. Press the “Settings” button to open the Settings menu.
3. Press the “Favorites” button.
3. Press the “Favorites” button.
4. Press the Favorite you want to rename.
4. Press the Favorite you want to delete.
Use the left and right arrows to choose another
Favorite from your list.
5. Press the “Rename” button.
Use the left and right arrows to choose another
Favorite from your list.
5. Press the “Delete” button.
6. Type in the new name and then press the “Done” 6. Press the “Yes” button to confirm the deletion.
button.
7. Press the “Done” button.
7. Press the “Done” button.
NAVIGATION 115
Important Safety Notices And Warnings
This Document
Great care was taken in preparing this document. Constant product development may mean that some inforThe Global Positioning System (GPS) is a satellite-based
mation is not entirely up to date. The information in this
system that provides location and timing information
document is subject to change without notice.
around the globe. GPS is operated and controlled under
the sole responsibility of the Government of the United TomTom shall not be liable for technical or editorial
States of America which is responsible for its availability errors or omissions contained herein, nor for incidental or
and accuracy. Any changes in GPS availability and accu- consequential damages resulting from the performance
racy, or in environmental conditions, may impact the or use of this document. This document contains inforoperation of this navigation system. TomTom does not mation protected by copyright. No part of this document
accept any liability for the availability and accuracy of may be photocopied or reproduced in any form without
GPS.
prior written consent from TomTom N.V.
Global Positioning System
Use With Care
Copyright Notices
Use of TomTom navigation while driving still means that © 2015 TomTom. All rights reserved. TomTom and the
⬙two hands⬙ logo are registered trademarks of TomTom
you need to drive with due care and attention.
N.V. or one of its subsidiaries. Please see
9
116 NAVIGATION
www.tomtom.com/en_us/legal/ for warranties and us.support.tomtom.com/app/answers/list. Upon reend user license agreements applying to this product.
quest, we will send you a CD with the corresponding
source code.
© 2015 TomTom. All rights reserved. This material is
proprietary and the subject of copyright protection Linotype, Frutiger and Univers are trademarks of Linoand/or database rights protection and/or other intellec- type GmbH registered in the U.S. Patent and Trademark
tual property rights owned by TomTom or its suppliers. Office and may be registered in certain other jurisdicThe use of this material is subject to the terms of a license tions. MHei is a trademark of The Monotype Corporation
agreement. Any unauthorized copying or disclosure of and may be registered in certain jurisdictions.
this material will lead to criminal and civil liabilities.
Data Source © 2015 TomTom All rights reserved.
The software included in this product contains copyrighted software that is licensed under the GPL. A copy
of that license can be viewed in the License section. You
can obtain the complete corresponding source code from
us for a period of three years after our last shipment of
this product. For more information, visit http://
www.tomtom.com/en_gb/gpl/ or contact your local
TomTom
customer
support
team
via
Uconnect 5.0/5.0 NAV
Owner’s Manual Supplement
16UC5PMC-526-AB
Second Edition Rev 1
Uconnect 5.0/5.0 NAV
Printed in the USA
©2015 FCA US LLC. All Rights Reserved.
Chrysler, Dodge, Jeep, Ram, Mopar and Uconnect are trademarks of FCA US LLC.
FIAT is a registered trademark of FCA Group Marketing S.p.A.,
used under license by FCA US LLC.