®
DIMMABLE
TOUCHDIAL™
ADJUSTABLE KELVIN
COLOR-CHANGING
OPERATION GUIDE
Mobile App
TABLE OF CONTENTS
1. CONNECT MOBILE DEVICE TO TOUCHDIAL WIFI HUB
1.1 Connect Mobile Device to Home WiFi Network (Preferred)
1.2 Connect Mobile Device Directly to TOUCHDIAL WiFi Hub
2. PAIR MOBILE APP TO TOUCHDIAL RECEIVER
3. FUNCTIONALITY
3.1 COLOR WHEEL
A. Fine Tuner
B. Master Dimmer
C. White Dimmer
D. Dynamic Mode
3.2 ROOM
3.3 SETTING
A. Reset WiFi Settings
B. Security Settings
C. Edit Zone (Room) Information
• Change Zone Name
• Change Zone Picture
• Change Zone Color Wheel
• Syncing Without Access to TOUCHDIAL Receiver
• Reset Learning Without Access to TOUCHDIAL Receiver
4. ADDITIONAL RESOURCES
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
1 OF 6
2
2
2
3
3
3
3
4
4
4
4
4
4
4
5
6
IG061317-2.1
1. CONNECT MOBILE DEVICE TO TOUCHDIAL™ WIFI HUB
CHOOSE OPTION 1.1 OR 1.2 TO CONNECT MOBILE DEVICE TO TOUCHDIAL WiFi Hub.
Before connecting mobile device to TOUCHDIAL WiFi Hub, install TOUCHDIAL Receiver and TOUCHDIAL WiFi Hub. See following Installation Guides:
• TOUCHDIAL Receiver Installation Guide
• TOUCHDIAL WiFi Hub Installation Guide
1.1 CONNECT MOBILE DEVICE TO HOME WIFI NETWORK (PREFERRED)
This option allows user to control lights while connected to home WiFi network. Requires Network Router.
*CAT5 /RJ45 Cable
Wi Fi
*12VDC Adapter
a.Power TOUCHDIAL WiFi Hub with included 12VDC Adapter.
b.Connect TOUCHDIAL WiFi Hub to Network Router with included CAT5 Ethernet cable.
c.Go to WiFi settings in mobile device.
d.Connect to home WiFi network that is connected to TOUCHDIAL WiFi Hub via Ethernet cable.
Wi Fi
RF
Network Router
Smart Device
Not sold by Diode LED.
Not sold by Diode LED.
Compatiible with Solid Color,
K-RANGE, & RGB(W) luminaires.
TOUCHDIAL WiFI Hub
(*CAT5 Cable & 12VDC Adapter
included with WiFi Hub).
1.2 CONNECT MOBILE DEVICE DIRECTLY TO TOUCHDIAL WIFI HUB
This option allows user to control lights with mobile device when home network router is unavailable.
a.Power TOUCHDIAL WiFi Hub with included 12VDC Adapter.
a.Go to WiFi settings in mobile device.
b.Connect to network ‘Easyltng_**’
*12VDC Adapter
** indicates different numeric values for each WiFi Hub.
Wi Fi
RF
Smart Device
Not sold by Diode LED.
Compatiible with Solid Color,
K-RANGE, & RGB(W) luminaires.
Wi Fi
TOUCHDIAL WiFI Hub
CAT5 Cable Not Required.
(*CAT5 Cable & 12VDC Adapter
included with WiFi Hub)
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
2 OF 6
IG061317-2.1
2. PAIR MOBILE APP TO TOUCHDIAL
RECEIVER
3. FUNCTIONALITY
a. Download mobile application:
There are 4 controllers to adjust output of different luminaire types.
3.1 COLOR WHEEL
iOS App Store
Search ‘TOUCHDIAL’ and download application.
Compatibility: Requires iOS 7.0 or later. Compatible with iPhone, iPad,
and iPod Touch.
3-CH K-RANGE
RGB(W)
SOLID COLOR
DIMMING
2-CH K-RANGE
To change controller:
Google Play App Store
Search ‘TOUCHDIAL’ and download application.
iOS - Tap 3 Times
Android - Tap 2 Times
b.Open TOUCHDIAL app and select ROOM.
c.Select a zone (ex. Bedroom) and a green checkmark will appear.
d.Select ROOM again to open Color Wheel.
e.Press LEARNING KEY on TOUCHDIAL Receiver (ensure receiver is set
to MASTER function).
f. Scroll color wheel and luminaire will flash to indicate pairing.
a. iOS - Tap wheel 3 times.
Android - Tap wheel 2 times.
Then choose new color wheel.
b. Select edges and drag to new
color wheel.
A. FINE TUNER
Featured in RGB(W) & 3-CH K-RANGE controllers.
The Fine Tuner allows user to manually mix 3 colors between 0-255
brightness levels to achieve a preferred color.
The TOUCHDIAL Receiver may already have an existing color programmed
and must be cleared before tuning in a new color. To clear an existing
color, move each color slider bar between 1-255 and then back to 0. The
luminaire will now be off and the receiver is cleared.
b.
B. MASTER DIMMER
c.
Featured in RGB(W), 2-CH & 3-CH K-RANGE controllers.
d.
100% Brightness
SLAVE
LEARNING KEY
e.
D1+
D1─
D2+
D2─
DATA IN/OUT
GND
TOUCHDIAL™ Receiver
f.
OUTPUT TO LOAD
MASTER
POWER
INPUT
®
V+
W
W
W
W
V+
WW
CW
WW
CW
V−
V−
V+
V+
V+
R
G
B
W
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
The Master Dimmer adjusts brightness
of R,G,B, & W channels in sync from
100-1%. The W CH for RGBW luminaires
can be also be adjusted independently
in the WHITE DIMMER setting.
3 OF 6
1% Brightness
IG061317-2.1
3. FUNCTIONALITY CONT.
3.2 ROOM
C. WHITE DIMMER
Featured in RGB(W) controller.
100% Brightness
The White Dimmer adjusts brightness
of W channel from 100-0%.
0% Brightness
Hold W to also turn ON/OFF
when not in dimmer interface.
Short press to select/deselect
zone.
D. DYNAMIC MODE
Long press to turn zone ON/OFF.
3.3 SETTING
Featured in RGB(W), & 3-CH K-RANGE controllers.
Play,
Pause,
Next
There are 10 Dynamic Modes. Press
Play to run 1st mode. Press again to
pause. Press again to switch to next
mode.
LightSound
Fastest
Speed
A.
C.
Slowest
Speed
B.
LightSound
A. RESET WIFI SETTINGS
For use only when mobile device is directly connected to TOUCHDIAL
WIFI HUB.
Press to loop or shuffle music.
To reset WiFi settings to factory default:
Highest
Sensitivity
Lowest
Sensitivity
LightSound synchronizes LED lights to sounds and music. LED lights will
flash in various patterns when LightSound is turned on. Sync LED lights
to microphone or music stored on your mobile device.
a.Go to mobile device WiFi settings. Search and connect to
‘TOUCHDIAL WIFI Hub Wireless Network’.
b.Open TOUCHDIAL app and press ‘Setting’.
c.Press ‘Reset WiFi Settings’.
d.Press ‘Yes’.
B. SECURITY SETTINGS
For use only when mobile device is directly connected to TOUCHDIAL
WIFI HUB.
Use to change WiFi Network password and SSID Name.
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
4 OF 6
IG061317-2.1
FUNCTIONALITY CONT.
3.3 SETTING CONT.
Zone Name
C. EDIT ROOM INFORMATION
Zone Picture
(Use camera to
replace zone picture)
Color Wheel
Select/deselect color
wheel control)
In Edit Mode, press where green dots indicate to change Zone Name,
Zone Picture, and Color Wheel type. Press ‘Save’ to save settings.
Note: Once editing is complete, multiple zones can only be controlled
simultaneously if the same color wheel has been chosen for each zone.
Pairing Without Access to TOUCHDIAL Receiver
Follow these instructions to pair mobile device to TOUCHDIAL Receiver
if receiver is not in an accessible location.
The following steps must be performed within 15 seconds after
TOUCHDIAL Receiver is powered on.
If it’s required to pair each receiver to a separate zone then each receiver
must be on a dedicated circuit or all receivers on the circuit will pair to
the selected zone.
a.Open ROOM menu at bottom-left of screen. Choose room (green
checkmark).
b.Open SETTINGS menu and select ‘Edit Room Information’.
c.Turn main power of TOUCHDIAL receiver off, then back on.
d.Short press LEARNING as shown below and lights will blink.
e.Open COLOR WHEEL and scroll wheel to finish pairing.
Reset Learning ID Without Access to TOUCHDIAL Receiver
a.Turn main power of TOUCHDIAL receiver off, then back on.
b.Long press LEARNING for 5+ seconds until attached LED luminaire
flashes.
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
5 OF 6
IG061317-2.1
4. ADDITIONAL RESOURCES
Visit the product web page at www.DiodeLED.com for additional product specifications & warranty information.
TOUCHDIAL RGB/RGBW 4-ZONE REMOTE CONTROL SPECIFICATION SHEET
For full specifications.
TOUCHDIAL RECEIVER SPECIFICATION SHEET & INSTALLATION GUIDE
For full specifications and installation instructions.
TOUCHDIAL WIFI HUB SPECIFICATION SHEET & INSTALLATION GUIDE
For full specifications and installation instructions.
® Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2017 Elemental LED, Inc. All rights reserved. Specifications are subject to change without notice.
TOUCHDIAL™ MOBILE APP OPERATION GUIDE
6 OF 6
IG061317-2.1
Download PDF