Motherboard
ROG
MAXIMUS
X HERO
E13645
Revised Edition V2
November 2017
Copyright © 2017 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from https://www.asus.com/support/
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notification to the email address gpl@asus.com, stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).
ii
Contents
Safety information....................................................................................................... vi
About this guide......................................................................................................... vii
MAXIMUS X HERO specifications summary............................................................ ix
Package contents....................................................................................................... xv
Installation tools and components.......................................................................... xvi
Chapter 1:
1.1
1.1.1
Before you proceed...................................................................... 1-1
1.1.2
Motherboard layout...................................................................... 1-2
1.1.3
Central Processing Unit (CPU).................................................... 1-4
1.1.4
System memory........................................................................... 1-5
1.1.5
Expansion slots............................................................................ 1-7
1.1.6
Onboard buttons and switches.................................................... 1-9
1.1.7
Jumper and holes...................................................................... 1-13
1.1.8
Onboard LEDs........................................................................... 1-14
1.1.9
Internal connectors.................................................................... 1-16
Chapter 2:
2.1
Product Introduction
Motherboard overview................................................................................ 1-1
Basic Installation
Building your PC system............................................................................ 2-1
2.1.1
CPU installation........................................................................... 2-1
2.1.2
Cooling system installation.......................................................... 2-3
2.1.3
Motherboard installation............................................................... 2-5
2.1.4
DIMM installation......................................................................... 2-6
2.1.5
ATX power connection................................................................. 2-7
2.1.6
SATA device connection.............................................................. 2-7
2.1.7
Front I/O connector...................................................................... 2-8
2.1.8
Expansion card installation.......................................................... 2-9
2.1.9
M.2 installation........................................................................... 2-10
2.1.10
Fan holder installation................................................................ 2-11
2.2
BIOS update utility.................................................................................... 2-12
2.3
Motherboard rear and audio connections.............................................. 2-13
2.3.1
Rear I/O connection................................................................... 2-13
2.3.2
Audio I/O connections................................................................ 2-15
2.4
Starting up for the first time..................................................................... 2-17
2.5
Turning off the computer......................................................................... 2-17
iii
Chapter 3:
Knowing BIOS............................................................................................. 3-1
3.2
BIOS setup program................................................................................... 3-2
3.2.1
Advanced Mode........................................................................... 3-3
3.2.2
EZ Mode...................................................................................... 3-6
3.2.3
QFan Control............................................................................... 3-7
3.2.4
EZ Tuning Wizard........................................................................ 3-9
3.3
My Favorites.............................................................................................. 3-12
3.4
Main menu................................................................................................. 3-14
3.5
Extreme Tweaker menu............................................................................ 3-14
3.6
Advanced menu........................................................................................ 3-16
3.6.1
CPU Configuration..................................................................... 3-16
3.6.2
Platform Misc Configuration....................................................... 3-17
3.6.3
System Agent (SA) Configuration.............................................. 3-17
3.6.4
PCH Configuration..................................................................... 3-17
3.6.5
PCH Storage Configuration....................................................... 3-17
3.6.6
PCH-FW Configuration.............................................................. 3-18
3.6.7
ROG Effects............................................................................... 3-18
3.6.8
Onboard Devices Configuration................................................. 3-18
3.6.9
APM Configuration..................................................................... 3-20
3.6.10
Network Stack Configuration..................................................... 3-20
3.6.11
HDD/SSD SMART Information.................................................. 3-20
3.6.12
USB Configuration..................................................................... 3-20
3.7
Monitor menu............................................................................................ 3-21
3.8
Boot menu................................................................................................. 3-21
3.9
Tool menu.................................................................................................. 3-23
3.9.1
ASUS EZ Flash 3 Utility............................................................. 3-23
3.9.2
Secure Erase............................................................................. 3-24
3.9.3
ASUS Overclocking Profile........................................................ 3-25
3.9.4
ASUS SPD Information.............................................................. 3-25
3.9.5
Graphics Card Information......................................................... 3-25
3.10
Exit menu................................................................................................... 3-26
3.11
Updating BIOS........................................................................................... 3-27
3.11.1
iv
BIOS Setup
3.1
EZ Update.................................................................................. 3-27
3.11.2
ASUS EZ Flash 3....................................................................... 3-28
3.11.3
ASUS CrashFree BIOS 3........................................................... 3-30
Chapter 4:
4.1
RAID Support
RAID configurations................................................................................... 4-1
4.1.1
RAID definitions........................................................................... 4-1
4.1.2
Installing storage devices............................................................. 4-2
4.1.3Intel® Rapid Storage Technology in UEFI BIOS........................... 4-2
4.1.4Intel® Rapid Storage Technology Option ROM utility................... 4-6
4.2
Creating a RAID driver disk..................................................................... 4-10
4.2.1
Creating a RAID driver disk in Windows® .................................. 4-10
Appendix
Q-Code table............................................................................................................. A-1
Notices..................................................................................................................... A-5
ASUS contact information....................................................................................... A-9
v
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
vi
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
•
Before using the product, ensure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product Introduction
This chapter describes the features of the motherboard and the new technology it
supports. It includes description of the switches, jumpers, and connectors on the
motherboard.
•
Chapter 2: Basic Installation
This chapter lists the hardware setup procedures that you have to perform when
installing system components.
•
Chapter 3: BIOS Setup
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
•
Chapter 4: RAID Support
This chapter describes the RAID configurations.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS website
The ASUS website (www.asus.com) provides updated information on ASUS hardware
and software products.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
vii
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3>
viii
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
MAXIMUS X HERO specifications summary
Intel® Socket 1151 for 8th Gen Intel® Core™ Processors
CPU
Supports 14nm CPU
Supports Intel® Turbo Boost Technology 2.0*
*Intel® Turbo Boost Technology 2.0 support depends on the CPU type.
Chipset
Intel® Z370 Chipset
4 x DIMM, Max. 64GB DDR4 4133+(OC)* / 4000(OC)* / 3866(OC)* /
3733(OC)* / 3600(OC)* / 3466(OC)* / 3400(OC)* / 3333(OC)* /
3300(OC)* / 3200(OC)* / 3000(OC)* / 2800(OC)* / 2666 / 2400 /
2133 MHz, non-ECC, un-buffered memory
Memory
Dual Channel Memory Architecture
Supports Intel® Extreme Memory Profile (XMP)
* Hyper DIMM support is subject to the physical characteristics of
individual CPUs.
**Please refer to Memory QVL (Qualified Vendors List) for details.
New 8th Gen Intel® Core™ Processors
2 x PCIe 3.0 x16 slots (supports x16, x8/x8)
Intel® Z370 Chipset
Expansion slots
1 x PCIe 3.0 x16 slot (max. at x4 mode)*
3 x PCIe 3.0 x1 slots
*The PCIe x4_3 slot shares bandwidth with the PCIe x1_3 slot. The PCIe
x4_3 slot is set to x2 mode by default.
Integrated Graphics Processor- Intel® HD Graphics support
Multi-VGA output support : HDMI/DisplayPort
Graphic
- Supports DisplayPort 1.2 with max. resolution 4096 x 2304 @
60Hz
- Supports HDMI 1.4b with max. resolution 4096 x 2160 @ 24Hz
Maximum shared memory of 1024MB
Multi-GPU support
Supports NVIDIA® 2-Way/Quad-GPU SLI™ Technology
Supports AMD® 3-Way/Quad-GPU CrossFireX™ Technology
Intel® I219-V Gigabit LAN
LAN
Anti-surge LANGuard
ROG GameFirst IV
(continued on the next page)
ix
MAXIMUS X HERO specifications summary
Intel® Z370 Chipset with RAID 0, 1, 5, 10, and Intel Rapid
Storage Technology support
-1xM
.2_1 Socket 3 with M Key, type 2242/2260/2280
(supports PCIE 3.0 x4 and SATA modes)*
-1xM
.2_2 Socket 3 with M Key, type 2242/2260/2280
(supports PCIE 3.0 x4 mode)**
Storage
- 6 x SATA 6Gb/s ports
- Supports Intel® Smart Response Technology ***
- Ready for Intel® Optane™ Memory
*When the M.2_1 Socket 3 is operating in SATA mode, SATA port 1 will
be disabled.
**When the M.2_2 Socket 3 is operating in PCIEX4 mode, SATA port 5, 6
will be disabled.
*** This function will work depending on the CPU installed.
ROG SupremeFX S1220 8-Channel High Definition Audio
CODEC
- Supports up to 32-Bit/192kHz playback*
- Impedance sense for front and rear headphone outputs
- ES9023P High Definition DAC
- SupremeFX Shielding Technology
Audio
- Jack-detection, Multi-streaming, and Front Panel Jack-retasking
- Optical S/PDIF out port at back panel
-H
igh quality 120 dB SNR stereo playback output and 113 dB SNR
recording input
Audio Features:
- Sonic Studio III
- Sonic Radar III
* Due to limitations in HDA bandwidth, 32-Bit/192kHz is not supported for
8-channel audio.
Intel® Z370 Chipset
-6xU
SB 3.1 Gen 1 ports ( 4 ports at back panel [blue], 2 ports at
mid-board)
USB
-6xU
SB 2.0 ports (2 ports at back panel [black], 4 ports at midboard)
ASMedia® USB 3.1 Gen 2 controller
- 1 x USB 3.1 Gen 2 front panel connector
-2xU
SB 3.1 Gen 2 ports (1 Type-A [red] and 1 Type-C [black] at
back panel)
(continued on the next page)
x
MAXIMUS X HERO specifications summary
Extreme Engine Digi+
- MicroFine Alloy Choke
- NexFET Power Block MOSFET
- 10K Black Metallic Capacitors
OC Zone
- Start Button
- Reset Button
- Safe Boot Button
- ReTry Button
- LN2 Mode
- Slow Mode switch
Mem TweakIt
GameFirst IV
MemOK! Button
ROG RAMDisk
ROG RAMCache II
ROG Exclusive Features
ROG CloneDrive
ROG CPU-Z
Overwolf
ROG Aura
- Aura Lighting Control
- Aura RGB Strip Headers
- Aura Addressable RGB Header
KeyBot II
- One-click overclocking
- DirectKey
- Clr CMOS
- Power On
UEFI BIOS features:
- Extreme Tweaker
- Tweakers’ Paradise
- ROG SSD Secure Erase
- O.C. Profile
(continued on the next page)
xi
MAXIMUS X HERO specifications summary
ASUS Dual Intelligent Processors 5
- 5-Way Optimization tuning key perfectly consolidates TPU, DIGI+
Power Control, Fan Xpert 4, and Turbo App
ASUS Exclusive Features
- AI Suite 3
- Disk Unlocker
ASUS EZ DIY
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 3
- ASUS C.P.R.(CPU Parameter Recall)
Special Features
- MemOK!
ASUS Q-Design
- SafeSlot
- Q-Code
- Q-Connector
- Q-LED (CPU[red], DRAM[yellow], VGA[white], Boot Device
LED[green])
- Q-DIMM
BIOS Flashback Button
Clear CMOS Button
Pre-mounted IO Shield
1 x Clear CMOS Button
1 x BIOS Flashback Button
1 x HDMI 1.4b
1 x DisplayPort 1.2
Back I/O Ports
2 x USB 2.0 ports [black]
4 x USB 3.1 Gen1 ports [blue]
1 x Anti-surge LAN (RJ45) port
2 x USB 3.1 Gen 2 ports (1 x Type-A [red] and 1 x Type-C™ [black])
1 x Optical S/PDIF out
5 x Gold-plated audio jacks
(continued on the next page)
xii
MAXIMUS X HERO specifications summary
2 x AURA RGB headers
1 x AURA Addressable RGB header
1 x USB 3.1 Gen 2 front panel connector
1 x USB 3.1 Gen 1 header supports additional 2 USB 3.1 Gen 1
ports
2 x USB 2.0 headers support additional 4 USB 2.0 ports
6 x SATA 6Gb/s ports
1 x M.2_1 Socket 3 for M Key, type 2242/2260/2280 storage devices
support (Supports PCIE 3.0 x4 and SATA modes)
1 x M.2_2 Socket 3 for M Key, type 2242/2260/2280 storage devices
support (Supports PCIE 3.0 x4 mode)
1 x 4-Pin CPU fan connector
1 x 4-Pin CPU_OPT fan connector
3 x 4-Pin Chassis fan connectors
1 x EXT_Fan header
1 x 4-Pin W_PUMP+ connector
1 x W_IN header
Internal I/O Ports
1 x W_OUT header
1 x W_FLOW header
1 x 4-Pin AIO_PUMP connector
1 x H_AMP fan connector
1 x Thermal sensor connector
1 x 24-pin EATX power connector
1 x 8-pin EATX 12V power connector
1 x Start button
1 x Reset button
1 x Safe Boot button
1 x Retry button
1 x LN2 mode jumper
1 x Slow mode switch
1 x MemOK! Button
1 x Front panel audio connector (AAFP)
1 x TPM connector
1 x System panel connector
3 x 3D Mount screw ports
BIOS
1 x 128 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI3.0, WfM2.0,
SM BIOS 3.0, ACPI 6.0, Multi-language BIOS, ASUS EZ Flash
3, CrashFree BIOS 3, F11 EZ Tuning Wizard, F6 Qfan Control,
F3 My Favorites, Last Modified log, F12 PrintScreen, F3 Shortcut
functions and ASUS DRAM SPD (Serial Presence Detect) memory
information.
Manageability
WfM2.0, DMI3.0, WOL by PME, PXE
(continued on the next page)
xiii
MAXIMUS X HERO specifications summary
Drivers
AURA
ROG GameFirst IV
ROG RAMDisk
ROG RAMCache II
ROG CPU-Z
ROG Mem TweakIt
Overwolf
ROG Keybot II
Software
CloneDrive
Kaspersky® Anti-Virus
DAEMON Tools Software
Winzip
ASUS Utilities
Sonic Studio III
Sonic Radar III
Fan Xpert 4
Operating System
Support
Windows® 10 64-bit
Form Factor
ATX Form Factor, 12”x 9.6” (30.5cm x 24.4cm)
Specifications are subject to change without notice. Please refer to the ASUS website for
the latest specifications.
xiv
Package contents
Check your motherboard package for the following items.
Motherboard
1 x ROG MAXIMUS X HERO motherboard
1 x RGB LED extension cable
Cables
1 x RGB Addressable LED extension cable
2 x 2-in-1 SATA 6Gb/s cables
1 x SLI™ HB Bridge(2-way-M)
1 x Q-Connector
1 x ROG Coaster
1 x 3D printing mount kit
Accessories
1 x 10-in-1 ROG cable label
1 x CPU Installation Tool
1 x 2-in-1 M.2 Screw set
1 x ROG sticker
1 x Fan holder
Application DVD
1 x ROG motherboard support DVD
Documentation
1 x User guide
If any of the above items is damaged or missing, contact your retailer.
xv
Installation tools and components
1 Bag of screws
Phillips (cross) screwdriver
PC chassis
Power supply unit
Intel® LGA 1151 CPU
Intel® LGA 1151 compatible CPU Fan
DDR4 DIMM
SATA hard disk drive
SATA optical disc drive (optional)
Graphics card (optional)
The tools and components in the table above are not included in the motherboard package.
xvi
Product Introduction
Product Introduction
1.1
Motherboard overview
1.1.1
Before you proceed
1
Chapter 1
Chapter 1:
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
Unplug the power cord from the wall socket before touching any component.
•
Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due
to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
•
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, or components.
ROG MAXIMUS X HERO
1-1
1.1.2
Motherboard layout
Chapter 1
Refer to 1.1.9 Internal connectors and 2.3.1 Rear I/O connection for more information
about rear panel connectors and internal connectors.
1-2
Chapter 1: Product Introduction
Layout contents
ROG MAXIMUS X HERO
Page
1-20
1-4
Chapter 1
Connectors/Jumpers/Buttons and switches/Slots
1. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V)
2. LGA1151 CPU Socket
3. CPU, CPU optional, high amp, extension, and chassis fan connectors; water
pump+, and AIO pump connectors (4-pin CPU_FAN; 4-pin CPU_OPT;
4-pin H_AMP; 5-pin EXT_FAN; 4-pin W_PUMP+; 4-pin AIO_PUMP; 4-pin
CHA_FAN1-3)
4. AURA RGB headers (4-pin RGB_HEADER1-2)
5. DDR4 DIMM slots
6. Q-Code LED
7. MemOK! button
8. 3D Mount
9. USB 3.1 Gen 2 front panel connector (U31G2_E3)
10. M.2 sockets (M.2_1; M.2_2)
11. Intel® Z370 Serial ATA 6 Gb/s connectors (7-pin SATA6G_12; SATA6G_34;
SATA6G_56)
12. Water in, water out, and water flow connectors (2-pin W_IN; 2-pin W_OUT; 3-pin W_FLOW)
13. System panel connectors (10-1 pin F_PANEL; 4-pin SPEAKER)
14. USB 2.0 connectors (10-1 pin USB910; USB1112)
15. Thermal sensor connector (2-pin T_SENSOR)
16. USB 3.1 Gen 1 connector (20-1 pin U31G1_12)
17. TPM connector (14-1 pin TPM)
18. LN2 Mode jumper (3-pin LN2_MODE)
19. Slow Mode switch (SLOW_MODE)
20. ReTry button (RETRY_BUTTON)
21. Safe Boot button (SAFE_BOOT)
22. RESET button (RESET)
23. Power-on button (START)
24. Addressable RGB header (4-1 pin ADD_HEADER)
25. Front panel audio connector (10-1 pin AAFP)
26. LED connector (5-pin LED2_CON1)
1-19
1-23
1-5
1-15
1-10
1-13
1-17
1-25
1-16
1-25
1-21
1-18
1-22
1-17
1-26
1-13
1-12
1-11
1-11
1-9
1-9
1-24
1-18
1-22
1-3
1.1.3
Central Processing Unit (CPU)
Chapter 1
This motherboard supports the New 8th Gen Intel® Core™ processors on the LGA1151
package, with memory and PCI Express controllers integrated to support dual-channel (4
DIMM) DDR4 memory and 16 PCI Express 3.0/2.0 lanes.
Ensure that you install the correct CPU designed for LGA1151 socket only. DO NOT install
a CPU designed for LGA1150, LGA1155 and LGA1156 sockets in the LGA1151 socket.
1-4
•
Ensure that all power cables are unplugged before installing the CPU.
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components. ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1151 socket.
•
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
Chapter 1: Product Introduction
1.1.4
System memory
Chapter 1
The motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Modules
(DIMM) slots.
A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT
install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
Recommended memory configurations
ROG MAXIMUS X HERO
1-5
Memory configurations
You may install 2 GB, 4 GB, 8 GB, and 16 GB unbuffered and non‑ECC DDR4 DIMMs into
the DIMM sockets.
Chapter 1
You may install varying memory sizes in Channel A and Channel B. The system maps the
total size of the lower-sized channel for the dual-channel configuration. Any excess memory
from the higher-sized channel is then mapped for single-channel operation.
1-6
•
The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value.
•
For system stability, use a more efficient memory cooling system to support a full
memory load (4 DIMMs) or overclocking condition.
•
Always install the DIMMS with the same CAS Latency. For an optimum compatibility,
we recommend that you install memory modules of the same version or data code
(D/C) from the same vendor. Check with the vendor to get the correct memory
modules.
Chapter 1: Product Introduction
1.1.5
Expansion slots
Slot No.
Chapter 1
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.
Slot Description
1
PCIe x1_1 slot
2
PCIe x16/x8_1 slot
3
PCIe x1_2 slot
4
PCIe x8_2 slot
5
PCIe x1_3 slot
6
PCIe x4_3 slot
ROG MAXIMUS X HERO
1-7
PCIe operating mode
VGA Configuration
Chapter 1
PCIe_x16/x8_1
PCIe_x8_2
Single VGA/PCIe card
x16 (Recommend for single VGA)
N/A
Dual VGA/PCIe card
x8
x8
PCIe operating mode
PCIe Lane
Auto mode
x4 mode
PCIe_x1_3
x1
Disabled
PCIe_x4_3
x2
x4
•
We recommend that you provide sufficient power when running CrossFireX™ or SLI™
mode.
•
Connect chassis fans to the motherboard chassis fan connectors when using multiple
graphics cards for better thermal environment.
PCIe_x16/x8_1 slot switches to x8 mode when PCIe_x8_2 slot is occupied.
1-8
Chapter 1: Product Introduction
1.1.6
Onboard buttons and switches
1.
Chapter 1
Onboard buttons and switches allow you to fine-tune performance when working on a bare or
open-case system. This is ideal for overclockers and gamers who continually change settings
to enhance system performance.
Power-on button (START)
The motherboard comes with a power-on button that allows you to power up or wake
up the system. The button also lights up when the system is plugged to a power source
indicating that you should shut down the system and unplug the power cable before
removing or installing any motherboard component.
2.
RESET button (RESET)
Press the reset button to reboot the system.
ROG MAXIMUS X HERO
1-9
3.
MemOK! button (MemOK!)
Chapter 1
Installing DIMMs that are not compatible with the motherboard may cause system
boot failure, and the DRAM_LED near the MemOK! button lights continuously. Press
and hold the MemOK! button until the DRAM_LED starts blinking to begin automatic
memory compatibility tuning for successful boot.
1-10
•
Refer to section 1.1.8 Onboard LEDs for the exact location of the DRAM_LED.
•
The DRAM_LED also lights up when the DIMM is not properly installed. Turn off the
system and reinstall the DIMM before using the MemOK! function.
•
The MemOK! button does not function under Windows® OS environment.
•
During the tuning process, the system loads and tests failsafe memory settings. It
takes about 30 seconds for the system to test one set of failsafe settings. If the test
fails, the system reboots and test the next set of failsafe settings. The blinking speed
of the DRAM_LED increases, indicating different test processes.
•
Due to memory tuning requirement, the system automatically reboots when each
timing set is tested. If the installed DIMMs still fail to boot after the whole tuning
process, the DRAM_LED lights continuously. Replace the DIMMs with ones
recommended in the Memory QVL (Qualified Vendors Lists) at www.asus.com.
•
If you turn off the computer and replace DIMMs during the tuning process, the system
continues memory tuning after turning on the computer. To stop memory tuning, turn
off the computer and unplug the power cord for about 5–10 seconds.
•
If your system fails to boot up due to BIOS overclocking, press the MemOK! button
to boot and load the BIOS default settings. A message will appear during POST
reminding you that the BIOS has been restored to its default settings.
•
We recommend that you download and update to the latest BIOS version from www.asus.com after using the MemOK! function.
Chapter 1: Product Introduction
4.
Safe Boot button (SAFE_BOOT)
5.
Chapter 1
The Safe Boot button can be pressed anytime to force the system to reboot into the
BIOS safe mode. This button temporarily applies safe settings to the BIOS while
retaining any overclocked settings allowing you to modify the settings causing boot
failure. Use this button when overclocking or tweaking the settings of your system.
ReTry button (RETRY_BUTTON)
The ReTry button is specially designed for overclockers and is most useful during the
booting process where the Reset button is rendered useless. When pressed, it forces
the system to reboot while retaining the same settings to be retried in quick succession
to achieve a successful POST.
ROG MAXIMUS X HERO
1-11
6.
Slow Mode Switch (SLOW_MODE)
Chapter 1
Slow Mode Switch is employed during LN2 benching. The system may crash due to
the CPU being unstable when using extreme overclocking, enabling slow mode will
decrease the processor frequency and stabilize the system, allowing overclockers to
keep track of their overclocking data.
1-12
Chapter 1: Product Introduction
1.1.7
1.
Jumper and holes
LN2 Mode jumper (3-pin LN2_MODE)
2.
Chapter 1
With LN2 mode activated, the ROG motherboard is optimized to remedy the cold-boot
bug during POST and help the system boot successfully.
3D Mount
Secure 3D printed parts to these 3D Mount holes for a personalized motherboard.
•
Download 3D source files at http://www.asus.com.
•
Use the bundled 3D Mount screws to install the 3D printed parts.
ROG MAXIMUS X HERO
1-13
1.1.8
1.
Onboard LEDs
Q LEDs (CPU, DRAM, VGA, BOOT)
Chapter 1
Q LEDs check key components (CPU, DRAM, VGA card, and booting devices) in
sequence during motherboard booting process. If an error is found, the corresponding
LED remains lit until the problem is solved. This user-friendly design provides an
intuitive way to locate the root problem within seconds.
The Q LEDs provide the most probable cause of an error code as a starting point for
troubleshooting. The actual cause may vary from case to case.
2.
Hard Disk LED (HD_LED)
The Hard Disk LED is designed to indicate the hard disk activity. It blinks when data
is being written into or read from the hard disk drive. The LED does not light up when
there is no hard disk drive connected to the motherboard or when the hard disk drive
does not function.
1-14
Chapter 1: Product Introduction
3.
Q-Code LED
Chapter 1
The Q-Code LED design provides you with a 2-digit error code that displays the system
status. Refer to the Q-Code table on the following page for details.
•
The Q-Code LED provides the most probable cause of an error code as a starting
point for troubleshooting. The actual cause may vary from case to case.
•
Please refer to the Q-Code table in the Appendix section for more details.
ROG MAXIMUS X HERO
1-15
1.1.9
Internal connectors
1.Intel Z370 Serial ATA 6 Gb/s connectors (7-pin SATA6G_12; SATA6G_34;
SATA6G_56)
®
Chapter 1
These connectors connect to Serial ATA 6 Gb/s hard disk drives via Serial ATA 6 Gb/s
signal cables.
If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10
configuration with the Intel® Rapid Storage Technology through the onboard Intel®
Z370 chipset.
1-16
•
These connectors are set to [AHCI] by default. If you intend to create a Serial ATA
RAID set using these connectors, set the SATA Mode Selection item in the BIOS to
[Intel RST Premium With Intel Optane System Acceleration (RAID)].
•
Before creating a RAID set, refer to section RAID configurations or the manual
bundled in the motherboard support DVD.
•
When using NCQ, set the SATA Mode in the BIOS to [AHCI]. Refer to section SATA
Configuration for details.
Chapter 1: Product Introduction
2.
USB 3.1 Gen 2 front panel connector (U31G2_E3)
3.
Chapter 1
This connector allows you to connect a USB 3.1 Gen 2 module for additional USB 3.1
Gen 2 ports. The latest USB 3.1 Gen 2 connectivity provides data transfer speeds of
up to 10 Gbps. The next-generation standard is completely backward-compatible with
your existing USB devices.
USB 3.1 Gen 1 connector (20-1 pin U31G1_12)
This connector allows you to connect a USB 3.1 Gen 1 module for additional USB
3.1 Gen 1 front or rear panel ports. With an installed USB 3.1 Gen 1 module, you can
enjoy all the benefits of USB 3.1 Gen 1 including faster data transfer speeds of up to
5 Gbps, faster charging time for USB-chargeable devices, optimized power efficiency,
and backward compatibility with USB 2.0.
The USB 3.1 Gen 1 module is purchased separately.
The plugged USB 3.1 gen 1 device may run on xHCI or EHCI mode depending on the
operating system’s setting.
ROG MAXIMUS X HERO
1-17
4.
USB 2.0 connectors (10-1 pin USB910; USB1112)
Chapter 1
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specification that supports up to
480 MBps connection speed.
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
5.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
HD Audio standard. Connect one end of the front panel audio I/O module cable to this
connector.
We recommend that you connect a high-definition front panel audio module to this
connector to avail of the motherboard’s high-definition audio capability.
1-18
Chapter 1: Product Introduction
6.CPU, CPU optional, high amp, extension, and chassis fan connectors; water
pump+, and AIO pump connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin H_
AMP; 5-pin EXT_FAN; 4-pin W_PUMP+; 4-pin AIO_PUMP; 4-pin CHA_FAN1-3)
•
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow
inside the system may damage the motherboard components. These are not jumpers!
Do not place jumper caps on the fan connectors!
•
Ensure to fully insert the 4-pin CPU fan cable to the CPU fan connector.
•
For better Q-Fan functions, we recommend using 4-pin PWM fans when you connect
powerful fans (1A or above) onto the H_AMP_FAN connector.
•
Ensure to disable Q-Fan functions if you want to connect powerful 3-pin DC fans (1A
or above) onto the H_AMP_FAN connector.
•
Connect the pump cable from the all-in-one cooler (AIO cooler) to the AIO_PUMP
header, and connect the fan cables to the CPU_FAN and/or CPU_OPT header(s).
•
W_PUMP+ function support depends on water cooling device.
ROG MAXIMUS X HERO
Chapter 1
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
1-19
Header
Chapter 1
CPU_FAN
CPU_OPT
CHA_FAN1
CHA_FAN2
CHA_FAN3
AIO_PUMP
W_PUMP+
H_AMP
7.
Max. Current
Max. Power
Default Speed
Shared Control
1A
1A
1A
1A
1A
1A
3A
3A
12W
12W
12W
12W
12W
12W
36W
36W
Q-Fan Controlled
Q-Fan Controlled
Q-Fan Controlled
Q-Fan Controlled
Q-Fan Controlled
Full Speed
Full Speed
Q-Fan Controlled
A
A
B
B
-
ATX power connectors (24-pin EATXPWR; 8-pin EATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
1-20
•
For a fully configured system, we recommend that you use a power supply unit
(PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a
minimum power of 350 W.
•
Do not forget to connect the 8-pin EATX12V power plug. Otherwise, the system will
not boot.
•
We recommend that you use a PSU with a higher power output when configuring a
system with more power-consuming devices. The system may become unstable or
may not boot up if the power is inadequate.
•
If you want to use two or more high-end PCIe x16 cards, use a PSU with 1000W
power or above to ensure the system stability.
Chapter 1: Product Introduction
8.
System panel connectors (10-1 pin F_PANEL; 4-pin SPEAKER)
Chapter 1
These connectors supports several chassis-mounted functions.
•
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
•
Hard disk drive activity LED (2-pin HDD_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The HDD LED lights up or flashes when data is read from or written
to the HDD.
•
System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you to hear system beeps and warnings.
•
ATX power button/soft-off button (2-pin PWRBTN)
This connector is for the system power button. Pressing the power button turns
the system on or puts the system in sleep or soft-off mode depending on the BIOS
settings. Pressing the power button for more than four seconds while the system is ON
turns the system OFF.
•
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
ROG MAXIMUS X HERO
1-21
9.
Thermal sensor connector (2-pin T_SENSOR)
This connector is for the thermistor cable that allows you to monitor the temperature of
your motherboard’s critical components and connected devices.
Chapter 1
10. LED connector (5-pin LED2_CON1)
This connector is for connecting LED strips on your back I/O cover.
1-22
Chapter 1: Product Introduction
11. AURA RGB headers (4-pin RGB_HEADER1-2)
Chapter 1
These connectors are for RGB LED strips.
The RGB header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum
power rating of 3A (12V), and no longer than 3 m.
Before you install or remove any component, ensure that the ATX power supply is switched
off or the power cord is detached from the power supply. Failure to do so may cause severe
damage to the motherboard, peripherals, or components.
•
Actual lighting and color will vary with LED strip.
•
If your LED strip does not light up, check if the RGB LED extension cable and the
RGB LED strip is connected in the correct orientation, and the 12V connector is
aligned with the 12V header on the motherboard.
•
The LED strip will only light up when the system is operating.
•
The LED strip is purchased separately.
ROG MAXIMUS X HERO
1-23
12. Addressable RGB header (4-1 pin ADD_HEADER)
This connector is for individually addressable RGB WS2812B LED strips or WS2812B
based LED strips.
Chapter 1
The addressable RGB header supports WS2812B addressable RGB LED strips (5V/Data/
Ground), with a maximum power rating of 3A (5V) and a maximum of 60 LEDs.
Before you install or remove any component, ensure that the ATX power supply is switched
off or the power cord is detached from the power supply. Failure to do so may cause severe
damage to the motherboard, peripherals, or components.
1-24
•
Actual lighting and color will vary with LED strip.
•
If your LED strip does not light up, check if the addressable RGB LED strip is
connected in the correct orientation, and the 5V connector is aligned with the 5V
header on the motherboard.
•
The addressable RGB LED strip will only light up under the operating system.
•
The addressable RGB LED strip is purchased separately.
Chapter 1: Product Introduction
13. M.2 sockets (M.2_1; M.2_2)
Chapter 1
These sockets allow you to install M.2 SSD modules.
•
M.2_1 socket supports PCIe 3.0 x4 and SATA mode M Key design and type 2242 /
2260 / 2280 PCIe storage devices.
•
M.2_2 socket supports PCIe 3.0 x4 M Key design and type 2242 / 2260 / 2280 PCIe
storage devices.
•
These sockets support IRST (Intel® Rapid Storage Technology).
•
These sockets are Intel® Optane™ Memory Ready.
The M.2 SSD module is purchased separately.
14.Water in, water out, and water flow connectors (2-pin W_IN; 2-pin W_OUT;
3-pin W_FLOW)
These connectors allow you to connect sensors to monitor the temperature and flow
rate of your liquid cooling system. You can manually adjust the fans and water pump to
optimize the thermal efficiency of your liquid cooling system.
ROG MAXIMUS X HERO
1-25
15. TPM connector (14-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which securely
stores keys, digital certificates, passwords and data. A TPM system also helps
enhance network security, protect digital identities, and ensures platform integrity.
Chapter 1
The TPM module is purchased separately.
1-26
Chapter 1: Product Introduction
Chapter 2:
2
Basic Installation
Basic Installation
2.1
Building your PC system
The diagrams in this section are for reference only. The motherboard layout may vary with
models, but the installation steps are the same for all models.
2.1.1
CPU installation
Chapter 2
Ensure that you install the correct CPU designed for LGA1151 socket only. DO NOT install
a CPU designed for LGA1155 and LGA1156 sockets on the LGA1151 socket.
Top of CPU
Bottom of CPU
Bottom of CPU
ROG MAXIMUS X HERO
2-1
Top of CPU
Chapter 2
2-2
•
The CPU Installation Tool is only compatible on ASUS motherboards with a Intel®
LGA1151 socket.
•
Ensure that the CPU is firmly clicked into place before installing it onto the CPU socket
on the motherboard.
•
Use the CPU Installation Tool for installing the CPU only. DO NOT damage or bend
the CPU Installation Tool.
•
Always firmly hold both sides of the CPU Installation Tool when installing, removing, or
picking up the CPU Installation Tool.
•
Ensure to use a soft stable surface when installing the CPU to the CPU Installation
Tool to prevent CPU damage.
•
ASUS will not cover damages resulting from incorrect CPU installation/removal,
incorrect CPU orientation/placement, or other damages resulting from negligence by
the user.
Chapter 2: Basic Installation
2.1.2
Cooling system installation
Apply the Thermal Interface Material to the
CPU cooling system and CPU before you
install the cooling system, if necessary.
Chapter 2
To install the CPU heatsink and fan assembly
ROG MAXIMUS X HERO
2-3
To install an AIO cooler
Chapter 2
AIO_PUMP
CPU_FAN
CPU_OPT
2-4
Chapter 2: Basic Installation
Motherboard installation
1.
Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to
the chassis’ rear I/O panel.
2.
Place nine (9) screws into the holes indicated by circles to secure the motherboard to
the chassis.
Chapter 2
2.1.3
DO NOT over tighten the screws! Doing so can damage the motherboard.
ROG MAXIMUS X HERO
2-5
2.1.4
DIMM installation
Chapter 2
To remove a DIMM
2-6
Chapter 2: Basic Installation
ATX power connection
Chapter 2
2.1.5
Ensure to connect the 8-pin power plug.
2.1.6
SATA device connection
OR
ROG MAXIMUS X HERO
2-7
2.1.7
Front I/O connector
To install ASUS Q-Connector
To install USB 3.1 Gen 2 connector
USB 3.1 Gen 2
Chapter 2
This connector will only fit in one
orientation. Push the connector until it
clicks into place.
To install USB 3.1 Gen 1 connector
To install USB 2.0 connector
USB 3.1 Gen 1
USB 2.0
To install front panel audio connector
To install system speaker connector
AAFP
2-8
Chapter 2: Basic Installation
2.1.8
Expansion card installation
Chapter 2
To install PCIe x16 cards
To install PCIe x1 cards
ROG MAXIMUS X HERO
2-9
2.1.9
M.2 installation
Chapter 2
Supported M.2 type varies per motherboard.
2-10
Chapter 2: Basic Installation
2.1.10
Fan holder installation
Chapter 2
To install the Fan holder and fan
When using high performance settings whilst overclocking, ensure to install the fan holder
for additional fan(s).
•
You may install 12V (1A, 12W), 40mm x 40mm fans or 50mm x 50mm fans.
•
Ensure to the use the bundled screws that came with your fans.
•
Fans are purchased separately.
ROG MAXIMUS X HERO
2-11
2.2
BIOS update utility
USB BIOS Flashback
USB BIOS Flashback allows you to easily update the BIOS without entering the existing
BIOS or operating system. Simply insert a USB storage device to the USB port, press the
USB BIOS Flashback button for three seconds, and the BIOS is updated automatically.
To use USB BIOS Flashback:
1.
Insert a USB storage device to the USB Flashback port.
We recommend you to use a USB 2.0 storage device to save the latest BIOS version for
better compatibility and stability.
Chapter 2
2.
Visit https://www.asus.com/support/ and download the latest BIOS version for this
motherboard.
3.
Rename the file as M10H.CAP, then copy it to your USB storage device.
4.
Shut down your computer.
5.
Press the BIOS Flashback button for three seconds until the Flashback LED blinks
three times, indicating that the BIOS Flashback function is enabled.
USB BIOS Flashback button
6.
KeyBot port
USB BIOS Flashback port
Wait until the light goes out, indicating that the BIOS updating process is completed.
For more BIOS update utilities in BIOS setup, refer to the section 3.11 Updating BIOS in
Chapter 3.
2-12
•
Do not unplug portable disk, power system, or press the CLR_CMOS button while
BIOS update is ongoing, otherwise update will be interrupted. In case of interruption,
please follow the steps again.
•
If the light flashes for five seconds and turns into a solid light, this means that
the BIOS Flashback is not operating properly. This may be caused by improper
installation of the USB storage device and filename/file format error. If this scenario
happens, please restart the system to turn off the light.
•
Updating BIOS may have risks. If the BIOS program is damaged during the process
and results to the system’s failure to boot up, please contact your local ASUS Service
Center.
Chapter 2: Basic Installation
2.3
Motherboard rear and audio connections
2.3.1
Rear I/O connection
1.
Clear CMOS button (CLR_CMOS). Press this button to clear the BIOS setup
information only when the systems hangs due to overclocking.
2.
DisplayPort
3.
Intel® USB 2.0 ports 7, and 8. Upper port supports the KeyBot II feature, and lower
port supports USB BIOS Flashback function.
4.
Intel® USB 3.1 Gen 1 ports 3, 4, 5, and 6
5.
LAN (RJ-45) port*
6.
USB BIOS Flashback button
7.
HDMI port
8.
USB 3.1 Gen 2 Type-A port EA1
9.
USB 3.1 Gen 2 Type-C™ port EC2
10.
Optical S/PDIF OUT port
11.
Audio I/O ports**
Chapter 2
Rear panel connectors
* and ** : Refer to the tables on the next page for LAN port LEDs, and audio port definitions.
•
USB 3.1 Gen 1/Gen 2 devices can only be used as data storage only.
•
We strongly recommend that you connect your devices to ports with matching data
transfer rate. Please connect your USB 3.1 Gen 1 devices to USB 3.1 Gen 1 ports and
your USB 3.1 Gen 2 devices to USB 3.1 Gen 2 ports for faster and better performance
for your devices.
•
Due to the design of the Intel chipset, all USB devices connected to the USB 3.1 Gen
1 ports are controlled by the xHCI controller. Some legacy USB devices must update
their firmware for better compatibility.
•
When KeyBot II is activated, USB hot plug function of the KeyBot port (USB 3.1 Gen 1
port 7) will be temporarily disabled.
ROG MAXIMUS X HERO
2-13
* LAN ports LED indications
ACT/LINK SPEED
LED
LED
Activity Link LED
Speed LED
Status
Description
Status
Description
OFF
No link
OFF
10 Mbps connection
ORANGE
Linked
ORANGE
100 Mbps connection
BLINKING
Data activity
GREEN
1 Gbps connection
LAN port
** Audio 2, 4, 6 or 8-channel configuration
4-channel
6-channel
8-channel
Light Blue
Lime
Pink
Orange
Headset
2-channel
Line In
Line Out
Mic In
–
Line In
Front Speaker Out
Mic In
–
Side Speaker Out
Black
–
Rear Speaker Out
Line In
Front Speaker Out
Mic In
Center/Sub
woofer
Rear Speaker Out
Port
Chapter 2
2-14
Front Speaker Out
Mic In
Center/Sub
woofer
Rear Speaker Out
Chapter 2: Basic Installation
2.3.2
Audio I/O connections
Audio I/O ports
Chapter 2
Connect to Headphone and Mic
Connect to Stereo Speakers
Connect to 2 Speakers
ROG MAXIMUS X HERO
2-15
Connect to 4 Speakers
Connect to 6 Speakers
Chapter 2
Connect to 8 Speakers
2-16
Chapter 2: Basic Installation
Starting up for the first time
1.
After making all the connections, replace the system case cover.
2.
Ensure that all switches are off.
3.
Connect the power cord to the power connector at the back of the system chassis.
4.
Connect the power cord to a power outlet that is equipped with a surge protector.
5.
Turn on the devices in the following order:
a.
Monitor
b.
External SCSI devices (starting with the last device on the chain)
c.
System power
6.
After applying power, the system power LED on the system front panel case lights up.
For systems with ATX power supplies, the system LED lights up when you press the
ATX power button. If your monitor complies with the “green” standards or if it has a
“power standby” feature, the monitor LED may light up or change from orange to green
after the system LED turns on.
The system then runs the power-on self tests (POST). While the tests are running, the
BIOS beeps (refer to the BIOS beep codes table) or additional messages appear on
the screen. If you do not see anything within 30 seconds from the time you turned on
the power, the system may have failed a power-on test. Check the jumper settings and
connections or call your retailer for assistance.
7.
2.5
BIOS Beep
Description
One short beep
VGA detected
Quick boot set to disabled
No keyboard detected
One continuous beep followed by two
short beeps then a pause (repeated)
No memory detected
One continuous beep followed by three
short beeps
No VGA detected
One continuous beep followed by four
short beeps
Hardware component failure
Chapter 2
2.4
At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the
instructions in Chapter 3.
Turning off the computer
While the system is ON, press the power button for less than four seconds to put the system
on sleep mode or soft-off mode, depending on the BIOS setting. Press the power button
for more than four seconds to let the system enter the soft-off mode regardless of the BIOS
setting.
ROG MAXIMUS X HERO
2-17
Chapter 2
2-18
Chapter 2: Basic Installation
Chapter 3:
BIOS Setup
BIOS Setup
3.1
Knowing BIOS
3
The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI
architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily
navigate the new UEFI BIOS with the same smoothness as your operating system. The
term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
BIOS (Basic Input and Output System) stores system hardware settings such as storage
device configuration, overclocking settings, advanced power management, and boot
device configuration that are needed for system startup in the motherboard CMOS. In
normal circumstances, the default BIOS settings apply to most conditions to ensure
optimal performance. DO NOT change the default BIOS settings except in the following
circumstances:
•
An error message appears on the screen during the system bootup and requests you to
run the BIOS Setup.
•
You have installed a new system component that requires further BIOS settings or
update.
Chapter 3
Inappropriate BIOS settings may result to instability or boot failure. We strongly
recommend that you change the BIOS settings only with the help of a trained service
personnel.
When downloading or updating the BIOS file, rename it as M10H.CAP for this
motherboard.
ROG MAXIMUS X HERO
3-1
3.2
BIOS setup program
Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen
include navigation keys and brief onscreen help to guide you in using the BIOS Setup
program.
Entering BIOS at startup
To enter BIOS Setup at startup, press <Delete> or <F2> during the Power-On Self Test
(POST). If you do not press <Delete> or <F2>, POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
•
Press <Ctrl>+<Alt>+<Delete> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
After doing either of the three options, press <Delete> key to enter BIOS.
Chapter 3
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
•
Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
•
If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu or press hotkey <F5>. See section 3.10 Exit Menu
for details.
•
If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section 2.3.1 Rear I/O connection for
the location of the Clear CMOS button to clear RTC RAM.
•
The BIOS setup program does not support the Bluetooth devices.
Please visit ASUS website for the detailed BIOS content manual.
BIOS menu screen
The BIOS Setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from Setup Mode in Boot menu or by pressing the <F7> hotkey.
3-2
Chapter 3: BIOS Setup
3.2.1
Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure
the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section Boot menu for details.
MyFavorite(F3)
Scroll bar
Qfan Control(F6) EZ Tuning Wizard(F11) Hot Keys
Chapter 3
Configuration fields
Pop-up Menu
Menu bar
Language
Menu items
General help
Last modified settings
Go back to EZ Mode
Search on the FAQ
Displays the CPU temperature,
CPU, and memory voltage output
ROG MAXIMUS X HERO
3-3
Menu bar
The menu bar on top of the screen has the following main items:
My Favorites
For saving the frequently-used system settings and configuration.
Main
For changing the basic system configuration
Extreme Tweaker
For changing the overclocking settings
Advanced
For changing the advanced system settings
Monitor
For displaying the system temperature, power status, and changing
the fan settings.
Boot
For changing the system boot configuration
Tool
For configuring options for special functions
Exit
For selecting the exit options and loading default settings
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (My Favorites, Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the
menu bar have their respective menu items.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press <Enter>.
Language
This button above the menu bar contains the languages that you can select for your BIOS.
Click this button to select the language that you want to display in your BIOS screen.
Chapter 3
My Favorites (F3)
This button above the menu bar shows all BIOS items in a Tree Map setup. Select frequentlyused BIOS settings and save it to MyFavorites menu.
Refer to section 3.3 My Favorites for more information.
Q-Fan Control (F6)
This button above the menu bar displays the current settings of your fans. Use this button to
manually tweak the fans to your desired settings.
Refer to section 3.2.3 Q-Fan Control for more information.
EZ Tuning Wizard (F11)
This button above the menu bar allows you to view and tweak the overclocking settings of
your system. It also allows you to change the motherboard’s SATA mode from AHCI to RAID
mode.
Refer to section 3.2.4 EZ Tuning Wizard for more information.
3-4
Chapter 3: BIOS Setup
Search on FAQ
Move your mouse over this button to show a QR code, scan this QR code on your mobile
device to connect to the BIOS FAQ web page of the ASUS support website. You can also
scan the following QR code:
Hot keys
This button above the menu bar contains the navigation keys for the BIOS setup program.
Use the navigation keys to select items in the menu and change the settings.
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit
on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display
the other items on the screen.
General help
At the bottom of the menu screen is a brief description of the selected item. Use <F12> key
to capture the BIOS screen and save it to the removable storage device.
Configuration fields
Chapter 3
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and
press <Enter> to display a list of options.
Last Modified button
This button shows the items that you last modified and saved in BIOS Setup.
ROG MAXIMUS X HERO
3-5
3.2.2
EZ Mode
The EZ Mode provides you an overview of the basic system information, and allows you to
select the display language, system performance, mode and boot device priority. To access
the Advanced Mode, select Advanced Mode or press the <F7> hotkey for the advanced
BIOS settings.
To switch from Advanced Mode to EZ Mode, click EZ Mode(F7) or press the <F7> hotkey.
Displays the system properties of the selected mode.
Click < or > to switch EZ System Tuning modes
Displays the CPU/motherboard temperature,
CPU voltage output, CPU/chassis/power fan
speed, and SATA information
Selects the display language
of the BIOS setup program
Creates storage RAID and
configures system overclocking
Chapter 3
Enables or disables the SATA RAID mode
for Intel Rapid Storage Technology
Displays the CPU Fan’s speed. Click
the button to manually tune the fans
Loads optimized
default settings
Saves the changes
and resets the system
Click to go to Advanced mode
Search on the FAQ
Click to display boot devices
Selects the boot device priority
The boot device options vary depending on the devices you installed to the system.
3-6
Chapter 3: BIOS Setup
3.2.3
QFan Control
The QFan Control allows you to set a fan profile or manually configure the operating speed of
your CPU and chassis fans.
Click to select a fan to be
configured
Click to activate DC Mode
Click to apply the fan setting
Click to undo the
changes
Click to go back to main menu
Chapter 3
Select a profile to
apply to your fans
Click to activate
PWM Mode
Select to manually configure
your fans
ROG MAXIMUS X HERO
3-7
Configuring fans manually
Select Manual from the list of profiles to manually configure your fans’ operating speed.
Speed points
Select to manually
configure your fans
To configure your fans:
Chapter 3
3-8
1.
Select the fan that you want to configure and to view its current status.
2.
Click and drag the speed points to adjust the fans’ operating speed.
3.
Click Apply to save the changes then click Exit (ESC).
Chapter 3: BIOS Setup
3.2.4
EZ Tuning Wizard
EZ Tuning Wizard allows you to easily overclock your CPU and DRAM, computer usage, and
CPU fan to their best settings. You can also set RAID in your system using this feature.
OC setup
RAID setup
OC Tuning
To start OC Tuning:
1.
Press <F11> on your keyboard or click
EZ Tuning Wizard screen.
2.
Click OC then click Next.
3.
Select a PC scenario Daily Computing or Gaming/Media Editing, then click Next.
ROG MAXIMUS X HERO
Chapter 3
from the BIOS screen to open
3-9
4.
Select a Main Cooling System BOX cooler, Tower cooler, Water cooler, or I’m not
sure, then click Next.
5.
After selecting the Main Cooling System, click Next then click Yes to start the OC
Tuning.
Creating RAID
To create RAID:
1.
Press <F11> on your keyboard or click
EZ Tuning Wizard screen.
2.
Click RAID then click Next.
3.
from the BIOS screen to open
•
Ensure that your HDDs have no existing RAID volumes.
•
Ensure to connect your HDDs to Intel® SATA connectors.
Select the port that you want to set to [RAID] mode, PCIE or SATA, then click Next.
Chapter 3
3-10
Chapter 3: BIOS Setup
Select the type of storage for your RAID, Easy Backup or Super Speed, then click
Next.
a.
For Easy Backup, click Next then select from Easy Backup (RAID1) or Easy
Backup (RAID10).
Chapter 3
4.
You can only select Easy Backup (RAID 10) if you connect four (4) HDDs.
b.
For Super Speed, click Next then select from Super Speed (RAID0) or Super
Speed (RAID5).
5.
After selecting the type of RAID, click Next then click Yes to continue the RAID setup.
6.
After the RAID setup is done, click Yes to exit the setup then click OK to reset your
system.
ROG MAXIMUS X HERO
3-11
3.3
My Favorites
My Favorites is your personal space where you can easily save and access your favorite
BIOS items.
Chapter 3
My Favorites comes with several performance, power saving, and fast boot related items by
default. You can personalize this screen by adding or removing items.
3-12
Chapter 3: BIOS Setup
Adding items to My Favorites
To add BIOS items:
from the BIOS screen to open
1.
Press <F3> on your keyboard or click
Setup Tree Map screen.
2.
On the Setup Tree Map screen, select the BIOS items that you want to save in My
Favorites screen.
Main menu panel
Selected shortcut
items
Submenu panel
Delete all favorite
items
Recover to default
favorite items
3.
Select an item from main menu panel, then click the submenu that you want to save as
or press <Enter> on your keyboard.
favorite from the submenu panel and click
•
Items with submenu options
•
User-managed items such as language and boot order
•
Configuration items such as Memory SPD Information, system time and date.
4.
Click Exit (ESC) or press <Esc> key to close Setup Tree Map screen.
5.
Go to My Favorites menu to view the saved BIOS items.
ROG MAXIMUS X HERO
Chapter 3
You cannot add the following items to My Favorite items:
3-13
3.4
Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
Security
The Security menu items allow you to change the system security settings.
3.5
•
If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 2.3.1 Rear I/O connection for the
location of the Clear CMOS button to clear RTC RAM.
•
The Administrator or User Password items on top of the screen show the default [Not
Installed]. After you set a password, these items show [Installed].
Extreme Tweaker menu
The Extreme Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Extreme Tweaker menu items. Incorrect
field values can cause the system to malfunction
The configuration options for this section vary depending on the CPU and DIMM model you
installed on the motherboard.
Ai Overclock Tuner
Chapter 3
Allows you to select the CPU overclocking options to achieve the desired CPU internal
frequency. Configuration options:
[Auto]
Loads the optimal settings for the system.
[Manual]
Allows you to individually set overclocking parameters.
[X.M.P.]
If you install memory modules supporting the eXtreme Memory Profile
(X.M.P.) Technology, choose this item to set the profiles supported by your
memory modules for optimizing the system performance.
The [X.M.P.] configuration option appears only when you install memory modules
supporting the eXtreme Memory Profile(X.M.P.) Technology.
The following item appears only when you set the Ai Overclocking Tuner to [Manual].
BCLK Frequency
This item allows you to set the BCLK (base clock) frequency to enhance the system
performance. Use the <+> or <-> to adjust the value. The values range from 40.0 MHz
to 650.0 MHz.
We recommend you to set the value based on the CPU specification, as high BCLK
frequencies may damage the CPU permanently.
3-14
Chapter 3: BIOS Setup
ASUS MultiCore Enhancement
[Auto]
This item allows you to maximize the oveclocking performance optimized
by ASUS core ratio settings.
[Disabled]
This item allows you to set to default core ratio settings.
CPU Core Ratio
This item allows you to set the CPU core ratios.
Configuration options: [Auto] [Sync All Cores] [Per Core]
DRAM Frequency
This item allows you to set the memory operating frequency. The configurable options vary
with the BCLK (base clock) frequency setting. Select the auto mode to apply the optimized
setting.
Configuration options: [Auto] [DDR4-800MHz] - [DDR4-8533MHz]
TPU
This item allows you to automatically overclock the CPU and DRAM frequencies and voltage
for an enhanced system performance.
[Keep Current Settings]
Keep the current settings without changing anything.
[TPU I]
Applies air cooling overclocking conditions.
[TPU II]
Applies water cooling overclocking conditions.
Ensure to use water cooling device before selecting [TPU II].
Internal CPU Power Management
The subitems in this menu allow you to set the CPU ratio and features.
Chapter 3
Intel(R) SpeedStep(tm)
Allows the operating system to dynamically adjust the processor voltage and cores
frequency to decrease the average power consumption and decrease average heat
production.
Configuration options: [Enabled] [Disabled]
Turbo Mode
Allows you to enable your processor cores to run faster than the base operating
frequency when it is below power, current and specification limit.
Configuration options: [Disabled] [Enabled]
ROG MAXIMUS X HERO
3-15
3.6
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
3.6.1
CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items in this menu may vary based on the CPU installed.
Hyper-threading
This item allows a hyper-threading processor to appear as two logical processors, allowing
the operating system to schedule two threads or processors simultaneously.
Configuration options: [Disabled] [Enabled]
CPU Power Management Configuration
This item allows you to manage and configure the CPU’s power.
Intel(R) SpeedStep(tm)
This item allows more than two frequency to be supported.
Configuration options: [Auto] [Enabled] [Disabled]
Turbo Mode
Chapter 3
This item allows you to automatically set the CPU cores to run faster than the base
operating frequency when it is below the operating power, current and temperature
specification limit.
Configuration options: [Enabled] [Disabled]
CPU C-States
This item allows you to set the power saving of the CPU states.
Configuration options: [Auto] [Disabled] [Enabled]
3-16
Chapter 3: BIOS Setup
3.6.2
Platform Misc Configuration
The items in this menu allow you to change the ASPM for PCH and SA PCI Express.
3.6.3
System Agent (SA) Configuration
The items in this menu allow you to adjust the Link Speed for PEG Port and Multi-Monitor.
3.6.4
PCH Configuration
The items in this menu allow you to adjust the PCH PCI Express speed.
PCI Express Configuration
This item allows you to configure the PCI Express slots.
PCIe Speed
This item allows your system to automatically select the PCI Express port speed.
Configuration options: [Auto] [Gen1] [Gen2] [Gen3]
3.6.5
PCH Storage Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Not Present if no SATA device is installed to the corresponding SATA
port.
SATA Controller(s)
This item allows you to enable or disable the SATA Device.
Configuration options: [Disabled] [Enabled]
Chapter 3
The following items appear only when you set the SATA Controller(s) to [Enabled].
SATA Mode Selection
This item allows you to set the SATA configuration.
[AHCI]
Set to [AHCI] when you want the SATA hard disk drives to
use the AHCI (Advanced Host Controller Interface). The
AHCI allows the onboard storage driver to enable advanced
Serial ATA features that increases storage performance on
random workloads by allowing the drive to internally optimize
the order of commands.
[Intel RST Premium
With Intel Optane
System Acceleration
(RAID)]
Set to [Intel RST Premium With Intel Optane System
Acceleration (RAID)] when you want to create a RAID
configuration from the SATA hard disk drives.
ROG MAXIMUS X HERO
3-17
S.M.A.R.T. Status Test
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system that
shows a warning message during POST (Power-on Self Test) when an error occurs in the
hard disks.
Configuration options: [On] [Off]
SATA6G_1 - SATA6G_6
SATA6G_1 - SATA6G_6
This item allows you to enable or disable the selected SATA port.
Configuration options: [Disabled] [Enabled]
Hot Plug
These items appears only when the SATA Mode Selection is set to [AHCI] and allows
you to enable or disable SATA Hot Plug Support.
Configuration options: [Disabled] [Enabled]
3.6.6
PCH-FW Configuration
This item allows you to configure the firmware TPM.
3.6.7
ROG Effects
The items in this menu allow you to configure the LEDs on your motherboard and the
functions for the Q-Code LED.
Onboard LED
This item allows you to enable all the onboard LEDs.
Configuration options: [Enabled] [Disabled]
Chapter 3
Q-Code LED Function
[Auto]Automatically display POST (Power-On Self-Test) code and CPU
temperature on Q-Code LED.
[POST Code Only] Show POST (Power-On Self-Test) code on Q-Code LED.
3.6.8
Onboard Devices Configuration
The items in this menu allow you to switch between PCIe Lanes and configure onboard
devices.
HD Audio Controller
This item allows you to use the Azalia High Definition Audio Controller
Configuration options: [Disabled] [Enabled]
3-18
Chapter 3: BIOS Setup
M.2_1 Configuration: [Auto][SATA mode][PCIE mode]
[Auto]
Auto-detects the M.2 device mode. If a SATA device is detected,
SATA6G_1 will be disabled.
[SATA mode]
Only supports M.2 SATA devices. Please note that SATA6G_1 port cannot
be used in this mode.
[PCIE mode]
Only supports M.2 PCIE devices.
M.2_2 PCIe Bandwidth Configuration: [X2][X4]
[X2]
Run at X2 mode with SATA6G_56 enabled.
[X4]
Run at X4 mode for higher performance with SATA6G_56 disabled.
USB Type C Power Switch
[Auto]The system will automatically detect your USB Type C devices and provide
suitable power if needed.
[Enabled]
The USB Type C port will always provide power to your devices.
RGB LED lighting
When system is in working state
This item allows you to turn the RGB LED lighting on or off when the system is in the
working state.
Configuration options: [On] [Off]
When system is in sleep, hibernate or soft off states
This item allows you to turn the RGB LED lighting on or off when the system is in the
sleep, hibernate or soft off states.
Configuration options: [On] [Off]
Intel LAN Controller
ROG MAXIMUS X HERO
Chapter 3
This item allows you to enable or disable the Intel LAN controllers.
Configuration options: [Disabled] [Enabled]
3-19
3.6.9
APM Configuration
The items in this menu allow you to set system wake and sleep settings.
ErP Ready [Disabled]
This item allows you to switch off some power at S4+S5 or S5 to get the system ready for
ErP requirement. When set to [Enabled], all other PME options are switched off.
Configuration options: [Disabled] [Enable(S4+S5)] [Enable(S5)]
3.6.10
Network Stack Configuration
The items in this menu allow you to configure Ipv4 / Ipv6 PXE support.
3.6.11
HDD/SSD SMART Information
This menu displays the SMART information of the connected devices.
NVM Express devices do not support SMART information.
3.6.12
USB Configuration
The items in this menu allow you to change the USB-related features.
The Mass Storage Devices item shows the auto-detected values. If no USB device is
detected, the item shows None.
Chapter 3
USB Single Port Control
This item allows you to enable or disable the individual USB ports.
Refer to section 1.1.2 Motherboard layout for the location of the USB ports.
3-20
Chapter 3: BIOS Setup
3.7
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
Scroll down to display the other BIOS items.
Qfan Configuration
Qfan Tuning
Click this item to automatically detect the lowest speed and configure the minimum
duty cycle for each fan.
AIO PUMP/W_PUMP+ Control
[Disabled]
Disable the Water Pump control feature.
[Auto]
Detects the type of water pump installed and automatically switches
the control modes.
[DC mode]
Enable the Water Pump control in DC mode for 3-pin chassis fan.
[PWM mode]
Enable the Water Pump control in PWM mode for 4-pin chassis fan.
3.8
Boot menu
The Boot menu items allow you to change the system boot options.
Fast Boot
[Disabled]
Allows your system to go back to its normal boot speed.
[Enabled]
Allows your system to accelerate the boot speed.
Chapter 3
The following item appears only when you set the Fast Boot to [Enabled].
Next Boot after AC Power Loss
[Normal Boot] Returns to normal boot on the next boot after an AC power loss.
[Fast Boot]
Accelerates the boot speed on the next boot after an AC power loss.
Setup Mode
[Advanced Mode]This item allows you to go to Advanced Mode of the BIOS after
POST.
[EZ Mode]
ROG MAXIMUS X HERO
This item allows you to go to EZ Mode of the BIOS after POST.
3-21
CSM (Compatibility Support Module)
This item allows you to configure the CSM (Compatibility Support Module) items to fully
support the various VGA, bootable devices and add-on devices for better compatibility.
Launch CSM
[Auto]
The system automatically detects the bootable devices and the addon devices.
[Enabled]
For better compatibility, enable the CSM to fully support the non-UEFI
driver add-on devices or the Windows® UEFI mode.
[Disabled]
Disable the CSM to fully support the non-UEFI driver add-on devices
or the Windows® UEFI mode.
The following items appear only when you set the Launch CSM to [Enabled].
Boot Devices Control
This item allows you to select the type of devices that you want to boot.
Configuration options: [UEFI and Legacy OPROM] [Legacy OPROM only]
[UEFI only]
Boot from Network Devices
This item allows you to select the type of network devices that you want to
launch.
Configuration options: [Ignore] [Legacy only] [UEFI driver first]
Boot from Storage Devices
This item allows you to select the type of storage devices that you want to
launch.
Configuration options: [Ignore] [Legacy only] [UEFI driver first]
Chapter 3
Boot from PCI-E/PCI Expansion Devices
This item allows you to select the type of PCI-E/PCI expansion devices that
you want to launch.
Configuration options: [Legacy only] [UEFI driver first]
Secure Boot
This item allows you to configure the Windows® Secure Boot settings and manage its keys to
protect the system from unauthorized access and malwares during POST.
3-22
Chapter 3: BIOS Setup
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
•
To access Windows® OS in Safe Mode, press <F8> after POST (Windows® 8 not
supported).
•
To select the boot device during system startup, press <F8> when the ASUS Logo
appears.
Boot Override
These items displays the available devices. The number of device items that appears on
the screen depends on the number of devices installed in the system. Click an item to start
booting from the selected device.
3.9
Tool menu
The Tool menu items allow you to configure options for special functions. Select an item then
press <Enter> to display the submenu.
Setup Animator
This item allows you to enable or disable the Setup animator.
Configuration options: [Disabled] [Enabled]
3.9.1
ASUS EZ Flash 3 Utility
Chapter 3
This item allows you to run ASUS EZ Flash 3. When you press <Enter>, a confirmation
message appears. Use the left/right arrow key to select between [Yes] or [No], then press
<Enter> to confirm your choice.
For more details, refer to section 3.11.2 ASUS EZ Flash 3.
ROG MAXIMUS X HERO
3-23
3.9.2
Secure Erase
SSD speeds may lower over time as with any storage medium due to data processing.
Secure Erase completely and safely cleans your SSD, restoring it to factory performance
levels.
Secure Erase is only available in AHCI mode. Ensure to set the SATA mode to AHCI. Click
Advanced > PCH Storage Configuration > SATA Mode Selection > AHCI.
To launch Secure Erase, click Tool > Secure Erase on the Advanced mode menu.
Check the ASUS support site for a full list of SSDs tested with Secure Erase. The drive may
become unstable if you run Secure Erase on an incompatible SSD.
•
The time to erase the contents of your SSD may take a while depending on its size.
Do not turn off the system during the process.
•
Secure Erase is only supported on Intel SATA port. For more information about Intel
SATA ports, refer to section 1.1.2 Motherboard layout of this manual.
Displays the
available SSDs
Chapter 3
Status definition:
3-24
•
Frozen. The frozen state is the result of a BIOS protective measure. The BIOS
guards drives that do not have password protection by freezing them prior to booting.
If the drive is frozen, a power off or hard reset of your PC must be performed to
proceed with the Secure Erase.
•
Locked. SSDs might be locked if the Secure Erase process is either incomplete
or was stopped. This may be due to a third party software that uses a different
password defined by ASUS. You have to unlock the SSD in the software before
proceeding with Secure Erase.
Chapter 3: BIOS Setup
3.9.3
ASUS Overclocking Profile
This item allows you to store or load multiple BIOS settings.
Load from Profile
This item allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the
profile number that saved your BIOS settings, press <Enter>, and then select Yes.
•
DO NOT shut down or reset the system while updating the BIOS to prevent the
system boot failure!
•
We recommend that you update the BIOS file only coming from the same memory/
CPU configuration and BIOS version.
Profile Name
This item allows you to key in a profile name.
Save to Profile
This item allows you to save the current BIOS settings to the BIOS Flash, and create a
profile. Key in a profile number from one to eight, press <Enter>, and then select Yes.
Load/Save Profile from/to USB Drive
This item allows you to load or save profile from your USB drive, load and save profile to your
USB drive.
3.9.4
ASUS SPD Information
3.9.5
Chapter 3
This item allows you to view the DRAM SPD information.
Graphics Card Information
This item displays the information about the graphics card installed in your system.
GPU Post
This item displays the information and recommended configuration for the PCIE slots that the
graphics card is installed in your system.
This feature is only supported on selected ASUS graphics cards.
Bus Interface
This item allows you to select the bus interface.
Configuration options: [PCIEX16/X8_1]
ROG MAXIMUS X HERO
3-25
3.10
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window appears.
Select OK to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a confirmation window appears. Select OK to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a confirmation window appears. Select Yes to
discard changes and exit.
Launch EFI Shell from USB drives
This item allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of
the available filesystem devices.
Chapter 3
3-26
Chapter 3: BIOS Setup
3.11
Updating BIOS
The ASUS website publishes the latest BIOS versions to provide enhancements on system
stability, compatibility,and performance. However, BIOS updating is potentially risky. If
there is no problem using the current version of BIOS, DO NOT manually update the BIOS.
Inappropriate BIOS updating may result to system’s failure to boot. Carefully follow the
instructions in this chapter to update your BIOS when necessary.
Visit http://www.asus.com to download the latest BIOS file for this motherboard.
The following utilities allow you to manage and update the motherboard BIOS setup program.
1.
EZ Update: Updates the BIOS in Windows® environment.
2.
ASUS EZ Flash 3: Updates the BIOS using a USB flash drive.
3.
ASUS CrashFree BIOS 3: Restores the BIOS using the motherboard support DVD or a
USB flash drive when the BIOS file fails or gets corrupted.
3.11.1
EZ Update
The EZ Update is a utility that allows you to update the motherboard BIOS in Windows®
environment.
EZ Update requires an Internet connection either through a network or an ISP
(Internet Service Provider).
•
This utility is available in the support DVD that comes with the motherboard package.
Chapter 3
•
ROG MAXIMUS X HERO
3-27
3.11.2
ASUS EZ Flash 3
ASUS EZ Flash 3 allows you to download and update to the latest BIOS through the Internet
without having to use a bootable floppy disk or an OS‑based utility.
Updating through the Internet varies per region and Internet conditions. Check your local
Internet connection before updating through the Internet.
To update the BIOS by USB:
Chapter 3
3-28
1.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter>.
2.
Insert the USB flash disk that contains the latest BIOS file to the USB port.
3.
Select via Storage Device(s).
4.
Press <Tab> to switch to the Drive field.
5.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
and then press <Enter>.
6.
Press <Tab> to switch to the Folder Info field.
7.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
Chapter 3: BIOS Setup
•
This function can support devices such as a USB flash disk with FAT 32/16 format and
single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability. Select
the Load Optimized Defaults item under the Exit menu. See section 3.10 Exit Menu for
details.
1.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter>.
2.
Select via Internet.
3.
Press the Left/Right arrow keys to select an Internet connection method, and then
press <Enter>.
4.
Follow the onscreen instructions to complete the update.
5.
Reboot the system when the update process is done.
Chapter 3
To update the BIOS by Internet:
Ensure to load the BIOS default settings to ensure system compatibility and stability. Select
the Load Optimized Defaults item under the Exit menu. See section 3.10 Exit Menu for
details.
ROG MAXIMUS X HERO
3-29
3.11.3
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the
BIOS file when it fails or gets corrupted during the updating process. You can restore a
corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains
the BIOS file.
The BIOS file in the motherboard support DVD may be older than the BIOS file published
on the ASUS official website. If you want to use the newer BIOS file, download the file at
https://www.asus.com/support/ and save it to a USB flash drive.
Recovering the BIOS
To recover the BIOS:
1.
Turn on the system.
2.
Insert the motherboard support DVD to the optical drive, or the USB flash drive
containing the BIOS file to the USB port.
3.
The utility automatically checks the devices for the BIOS file. When found, the utility
reads the BIOS file and enters ASUS EZ Flash 3 automatically.
4.
The system requires you to enter BIOS Setup to recover the BIOS setting. To ensure
system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
Chapter 3
3-30
Chapter 3: BIOS Setup
Chapter 4:
RAID Support
RAID Support
4.1
RAID configurations
4
The motherboard supports Intel® Rapid Storage Technology with RAID 0, RAID 1, RAID 5,
and RAID 10 solution.
If you want to install a Windows® operating system to a hard disk drive included in a RAID
set, you have to create a RAID driver disk and load the RAID driver during OS installation.
Refer to section 4.2 Creating a RAID driver disk for details.
4.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in
parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a
sustained data transfer rate, double that of a single disk alone, thus improving data access
and storage. Use of two new identical hard disk drives is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to
a second drive. If one drive fails, the disk array management software directs all applications
to the surviving drive as it contains a complete copy of the data in the other drive. This RAID
configuration provides data protection and increases fault tolerance to the entire system. Use
two new drives or use an existing drive and a new drive for this setup. The new drive must be
of the same size or larger than the existing drive.
RAID 5 strips both data and parity information across three or more hard disk drives. Among
the advantages of RAID 5 configuration include better HDD performance, fault tolerance, and
higher storage capacity. The RAID 5 configuration is best suited for transaction processing,
relational database applications, enterprise resource planning, and other business systems.
Use a minimum of three identical hard disk drives for this setup.
Chapter 4
RAID 10 is data striping and data mirroring combined without parity (redundancy data) having
to be calculated and written. With the RAID 10 configuration you get all the benefits of both
RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive
and three new drives for this setup.
ROG MAXIMUS X HERO
4-1
4.1.2
Installing storage devices
The motherboard supports Serial ATA hard disk drives and PCIE SSD storage devices. For
optimal performance, install identical drives of the same model and capacity when creating a
disk array.
Refer to Chapter 2 for details on installing storage devices to your motherboard.
4.1.3Intel® Rapid Storage Technology in UEFI BIOS
To enter the Intel® Rapid Storage Technology in UEFI BIOS:
1.
Enter the BIOS Setup during POST.
2.
Go to the Advanced menu > PCH Storage Configuration, then press <Enter>.
3.
Set the SATA Mode Selection item to [Intel RST Premium With Intel Optane System
Acceleration (RAID)].
If you are using PCIE storage devices, ensure to enable all the PCIE Storage RAID
Support items.
4.
Go to the Boot menu > CSM (Compatibility Support Module) > Launch CSM, then
set the item to [Disabled].
5.
Save your changes and exit the BIOS Setup, then enter the BIOS Setup again.
6.
Go to the Advanced menu > Intel(R) Rapid Storage Technology, then press <Enter>
to display the Intel® Rapid Storage Technology menu.
Refer to Chapter 3 for details on entering and navigating through the BIOS Setup.
Due to chipset limitation, when SATA ports are set to RAID mode, all SATA ports run at
RAID mode together.
Chapter 4
4-2
Chapter 4: RAID Support
Creating a RAID set
To create a RAID set:
1.
From the Intel® Rapid Storage Technology menu, select Create RAID Volume and
press <Enter>. The following screen appears:
2.
When the Name item is selected, enter a name for the RAID set and press <Enter>.
3.
When the RAID Level item is selected, press <Enter> to select the RAID level to
create, and then press <Enter>.
Chapter 4
4.Under Select Disks, press <Enter> and select X for the disks you want to include in
the RAID set.
ROG MAXIMUS X HERO
4-3
5.
When the Strip Size item is selected, press <Enter> to select strip size for the RAID
array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size
values range from 4 KB to 128 KB. The following are typical values:
-
RAID 0: 128 KB
-
RAID 10: 64 KB
-
RAID 5: 64 KB
We recommend a lower strip size for server systems, and a higher strip size for multimedia
computer systems used mainly for audio and video editing.
6.
When the Capacity (MB) item is selected, enter the RAID volume capacity that you
want and press <Enter>. The default value indicates the maximum allowed capacity.
7.
When the Create Volume item is selected, press <Enter> to create the RAID volume
and return to the Intel® Rapid Storage Technology menu.
Chapter 4
4-4
Chapter 4: RAID Support
Deleting a RAID set
Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set:
From the Intel® Rapid Storage Technology menu, select the RAID volume you want to
delete and press <Enter>. The following screen appears:
2.
When the Delete item is selected, press <Enter>, then select Yes to delete the RAID
volume and return to the Intel® Rapid Storage Technology menu, or select No to
cancel.
Chapter 4
1.
ROG MAXIMUS X HERO
4-5
4.1.4Intel® Rapid Storage Technology Option ROM utility
To enter the Intel® Rapid Storage Technology Option ROM utility:
1.
Turn on the system.
2.
During POST, press <Ctrl> + <I> to display the utility main menu.
RAID Volumes:
None defined.
Physical Devices:
Port
Device Model
0
ST3160812AS
1
ST3160812AS
2
ST3160812AS
3
ST3160812AS
Serial #
9LS0HJA4
9LS0F4HL
3LS0JYL8
9LS0BJ5H
Size
149.0GB
149.0GB
149.0GB
149.0GB
Type/Status(Vol ID)
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
The navigation keys at the bottom of the screen allow you to move through the menus
and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and may not
exactly match the items on your screen.
The utility supports maximum four hard disk drives for RAID configuration.
Chapter 4
4-6
Chapter 4: RAID Support
Creating a RAID set
To create a RAID set:
1.
From the utility main menu, select 1. Create RAID Volume and press <Enter>. The
following screen appears:
Name: Volume 0
RAID Level: aaaaaaaaaaaaaaa
Disks: dssdsdsds
Strip Size:aaaaaaaaaaaaaaaa
Capacity:aaaaaaaaaaaaaa
Sync:aaaaaaaaaa
Create volume
[HELP]
Enter a unique volume name that has no special characters
and is 16 characters or less.
2.
Enter a name for the RAID set and press <Enter>.
3.
When the RAID Level item is selected, press the up/down arrow key to select a RAID
level to create, and then press <Enter>.
4.
When the Disks item is selected, press <Enter> to select the hard disk drives you want
to include in the RAID set. The SELECT DISKS screen appears:
[SELECT DISKS]
Port
0
1
2
3
Device Model
ST3160812AS
ST3160812AS
ST3160812AS
ST3160812AS
Serial #
9LS0HJA4
9LS0F4HL
3LS0JYL8
9LS0BJ5H
Size
149.0GB
149.0GB
149.0GB
149.0GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 2 to 6 to use in creating the volume.
[SPACE]-SelectDisk
[ENTER]-Done
Chapter 4
[↑↓]-Prev/Next
ROG MAXIMUS X HERO
4-7
5.
Use the up/down arrow key to select a drive, and then press <Space> to select. A
small triangle marks the selected drive. Press <Enter> after completing your selection.
6.
Use the up/down arrow key to select the strip size for the RAID array (for RAID 0, 10
and 5 only), and then press <Enter>. The available strip size values range from 4 KB to
128 KB. The following are typical values:
-
RAID 0: 128 KB
-
RAID 10: 64 KB
-
RAID 5: 64 KB
We recommend a lower strip size for server systems, and a higher strip size for multimedia
computer systems used mainly for audio and video editing.
7.
When the Capacity item is selected, enter the RAID volume capacity that you want
and press <Enter>. The default value indicates the maximum allowed capacity.
8.
When the Create Volume item is selected, press <Enter>. The following warning
message appears:
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N)
9.
Press <Y> to create the RAID volume and return to the main menu, or <N> to go back
to the CREATE VOLUME menu.
Chapter 4
4-8
Chapter 4: RAID Support
Deleting a RAID set
Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set:
1.
From the utility main menu, select 2. Delete RAID Volume and press <Enter>. The
following screen appears:
Name
Volume0
[DELETE VOLUME MENU]
Level
Drives
RAID0 (Stripe)
2
Capacity
298.0GB
Status
Normal
Bootable
Yes
[HELP]
Deleting a volume will reset the disks to non-RAID.
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[↑↓]-Select
2.
[ESC]-Previous Menu
[DEL]-Delete Volume
Use the up/down arrow key to select the RAID set you want to delete, and then press
<Delete>. The following warning message appears:
[DELETE VOLUME VERIFICATION]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete “Volume0”? (Y/N):
Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to
return to the DELETE VOLUME menu.
Chapter 4
3.
ROG MAXIMUS X HERO
4-9
Exiting the Intel® Rapid Storage Technology Option ROM utility
To exit the utility:
1.
From the utility main menu, select 6. Exit, then press <Enter>. The following warning
message appears:
[CONFIRM EXIT]
Are you sure you want to exit? (Y/N):
2.
Press <Y> to exit or press <N> to return to the utility main menu.
4.2
Creating a RAID driver disk
4.2.1
Creating a RAID driver disk in Windows®
To install the RAID driver for Windows® OS:
1.
During the OS installation, click Load Driver to allow you to select the installation
media containing the RAID driver.
2. Insert the support USB drive with RAID driver into the USB port, and then click
Browse.
3. Click the name of the device you’ve inserted, go to Drivers > RAID, and then select
the RAID driver for the corresponding OS version. Click OK.
4. Follow the succeeding screen instructions to complete the installation.
To set up a Windows® UEFI operating system under RAID mode, ensure to load the UEFI
driver for your optical drive.
Chapter 4
4-10
Chapter 4: RAID Support
Appendix
Appendix
Code
00
01
02
03
04
06
Description
Not used
Power on. Reset type detection (soft/hard).
AP initialization before microcode loading
System Agent initialization before microcode loading
PCH initialization before microcode loading
Microcode loading
07
AP initialization after microcode loading
08
09
0B
0C – 0D
0E
0F
10
11 – 14
15 – 18
19 – 1C
2B – 2F
30
31
32 – 36
37 – 3A
3B – 3E
4F
System Agent initialization after microcode loading
PCH initialization after microcode loading
Cache initialization
Reserved for future AMI SEC error codes
Microcode not found
Microcode not loaded
PEI Core is started
Pre-memory CPU initialization is started
Pre-memory System Agent initialization is started
Pre-memory PCH initialization is started
Memory initialization
Reserved for ASL (see ASL Status Codes section below)
Memory Installed
CPU post-memory initialization
Post-Memory System Agent initialization is started
Post-Memory PCH initialization is started
DXE IPL is started
Memory initialization error. Invalid memory type or incompatible memory
speed
Unspecified memory initialization error
Memory not installed
Invalid CPU type or Speed
CPU mismatch
CPU self test failed or possible CPU cache error
CPU micro-code is not found or micro-code update is failed
Internal CPU error
Reset PPI is not available
Reserved for future AMI error codes
50 – 53
54
55
56
57
58
59
5A
5B
5C – 5F
Appendix
Q-Code table
(continued on the next page)
ROG MAXIMUS X HERO
A-1
Q-Code table
Code
Appendix
E0
E1
E2
E3
E4 – E7
E8
E9
EA
EB
EC – EF
F0
F1
F2
F3
F4
F5 – F7
F8
F9
FA
FB – FF
60
61
62
63 – 67
68
69
Description
S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)
S3 Boot Script execution
Video repost
OS S3 wake vector call
Reserved for future AMI progress codes
S3 Resume Failed
S3 Resume PPI not Found
S3 Resume Boot Script Error
S3 OS Wake Error
Reserved for future AMI error codes
Recovery condition triggered by firmware (Auto recovery)
Recovery condition triggered by user (Forced recovery)
Recovery process started
Recovery firmware image is found
Recovery firmware image is loaded
Reserved for future AMI progress codes
Recovery PPI is not available
Recovery capsule is not found
Invalid recovery capsule
Reserved for future AMI error codes
DXE Core is started
NVRAM initialization
Installation of the PCH Runtime Services
CPU DXE initialization is started
PCI host bridge initialization
System Agent DXE initialization is started
6A
System Agent DXE SMM initialization is started
6B – 6F
70
71
72
73 – 77
78
79
7A – 7F
System Agent DXE initialization (System Agent module specific)
PCH DXE initialization is started
PCH DXE SMM initialization is started
PCH devices initialization
PCH DXE Initialization (PCH module specific)
ACPI module initialization
CSM initialization
Reserved for future AMI DXE codes
(continued on the next page)
A-2
Appendix
Q-Code table
Description
Boot Device Selection (BDS) phase is started
Driver connecting is started
PCI Bus initialization is started
PCI Bus Hot Plug Controller Initialization
PCI Bus Enumeration
PCI Bus Request Resources
PCI Bus Assign Resources
Console Output devices connect
Console input devices connect
Super IO Initialization
USB initialization is started
USB Reset
USB Detect
USB Enable
Reserved for future AMI codes
IDE initialization is started
IDE Reset
IDE Detect
IDE Enable
SCSI initialization is started
SCSI Reset
SCSI Detect
SCSI Enable
Setup Verifying Password
Start of Setup
Reserved for ASL (see ASL Status Codes section below)
Setup Input Wait
Reserved for ASL (see ASL Status Codes section below)
Ready To Boot event
Legacy Boot event
Exit Boot Services event
Runtime Set Virtual Address MAP Begin
Runtime Set Virtual Address MAP End
Legacy Option ROM Initialization
System Reset
Appendix
Code
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E – 9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
(continued on the next page)
ROG MAXIMUS X HERO
A-3
Q-Code table
Appendix
Code
B4
B5
B6
B7
B8– BF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
Description
USB hot plug
PCI bus hot plug
Clean-up of NVRAM
Configuration Reset (reset of NVRAM settings)
Reserved for future AMI codes
CPU initialization error
System Agent initialization error
PCH initialization error
Some of the Architectural Protocols are not available
PCI resource allocation error. Out of Resources
No Space for Legacy Option ROM
No Console Output Devices are found
No Console Input Devices are found
Invalid password
Error loading Boot Option (LoadImage returned error)
Boot Option is failed (StartImage returned error)
Flash update is failed
Reset protocol is not available
ACPI/ASL Checkpoints
A-4
Code
Description
0x01
System is entering S1 sleep state
0x02
System is entering S2 sleep state
0x03
System is entering S3 sleep state
0x04
System is entering S4 sleep state
0x05
System is entering S5 sleep state
0x10
System is waking up from the S1 sleep state
0x20
System is waking up from the S2 sleep state
0x30
System is waking up from the S3 sleep state
0x40
System is waking up from the S4 sleep state
0xAC
System has transitioned into ACPI mode. Interrupt controller is in PIC mode.
0xAA
System has transitioned into ACPI mode. Interrupt controller is in APIC mode.
Appendix
Notices
Federal Communications Commission Statement
•
This device may not cause harmful interference.
•
This device must accept any interference received including interference that may cause
undesired operation.
Appendix
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
ROG MAXIMUS X HERO
A-5
Compliance Statement of Innovation, Science and Economic
Development Canada (ISED)
Appendix
This device complies with Innovation, Science and Economic Development Canada licence
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems.
CAN ICES-3(B)/NMB-3(B)
Déclaration de conformité de Innovation, Sciences et
Développement économique Canada (ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
La bande 5150–5250 MHz est réservée uniquement pour une utilisation à l’intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
CAN ICES-3(B)/NMB-3(B)
VCCI: Japan Compliance Statement
Class B ITE
KC: Korea Warning Statement
A-6
Appendix
REACH
Appendix
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling
information in different regions.
Regional notice for California
WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov
Google™ License Terms
Copyright© 2017 Google Inc. All Rights Reserved.
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file
except in compliance with the License. You may obtain a copy of the License at:
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the
License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF
ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under the
License.
ROG MAXIMUS X HERO
A-7
Appendix
English ASUSTeK Computer Inc. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions of
related Directives. Full text of EU declaration of conformity is available at:
www.asus.com/support
Français AsusTek Computer Inc. déclare par la présente que cet appareil est
conforme aux critères essentiels et autres clauses pertinentes des directives
concernées. La déclaration de conformité de l’UE peut être téléchargée à
partir du site Internet suivant : www.asus.com/support
Deutsch ASUSTeK Computer Inc. erklärt hiermit, dass dieses Gerät mit
den wesentlichen Anforderungen und anderen relevanten Bestimmungen
der zugehörigen Richtlinien übereinstimmt. Der gesamte Text der EUKonformitätserklärung ist verfügbar unter: www.asus.com/support
Italiano ASUSTeK Computer Inc. con la presente dichiara che questo
dispositivo è conforme ai requisiti essenziali e alle altre disposizioni pertinenti
con le direttive correlate. Il testo completo della dichiarazione di conformità
UE è disponibile all’indirizzo: www.asus.com/support
Русский Компания ASUS заявляет, что это устройство соответствует
основным требованиям и другим соответствующим условиям
соответствующих директив. Подробную информацию, пожалуйста,
смотрите на www.asus.com/support
Български С настоящото ASUSTeK Computer Inc. декларира, че това
устройство е в съответствие със съществените изисквания и другите
приложими постановления на свързаните директиви. Пълният текст на
декларацията за съответствие на ЕС е достъпна на адрес:
www.asus.com/support
Hrvatski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan
s bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o sukladnosti dostupan je na: www.asus.com/support
Čeština Společnost ASUSTeK Computer Inc. tímto prohlašuje, že toto
zařízení splňuje základní požadavky a další příslušná ustanovení souvisejících
směrnic. Plné znění prohlášení o shodě EU je k dispozici na adrese:
www.asus.com/support
Dansk ASUSTeK Computer Inc. erklærer hermed, at denne enhed er i
overensstemmelse med hovedkravene og andre relevante bestemmelser i de
relaterede direktiver. Hele EU-overensstemmelseserklæringen kan findes på:
www.asus.com/support
Nederlands ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat
voldoet aan de essentiële vereisten en andere relevante bepalingen van
de verwante richtlijnen. De volledige tekst van de EU-verklaring van
conformiteit is beschikbaar op: www.asus.com/support
Eesti Käesolevaga kinnitab ASUSTeK Computer Inc, et see seade vastab
asjakohaste direktiivide oluliste nõuetele ja teistele asjassepuutuvatele
sätetele. EL vastavusdeklaratsiooni täielik tekst on saadaval järgmisel
aadressil: www.asus.com/support
Suomi ASUSTeK Computer Inc. ilmoittaa täten, että tämä laite on
asiaankuuluvien direktiivien olennaisten vaatimusten ja muiden tätä
koskevien säädösten mukainen. EU-yhdenmukaisuusilmoituksen koko teksti
on luettavissa osoitteessa: www.asus.com/support
Ελληνικά Με το παρόν, η AsusTek Computer Inc. δηλώνει ότι αυτή η
συσκευή συμμορφώνεται με τις θεμελιώδεις απαιτήσεις και άλλες σχετικές
διατάξεις των Οδηγιών της ΕΕ. Το πλήρες κείμενο της δήλωσης συμβατότητας
είναι διαθέσιμο στη διεύθυνση: www.asus.com/support
Magyar Az ASUSTeK Computer Inc. ezennel kijelenti, hogy ez az eszköz
megfelel a kapcsolódó Irányelvek lényeges követelményeinek és egyéb
vonatkozó rendelkezéseinek. Az EU megfelelőségi nyilatkozat teljes szövege
innen letölthető: www.asus.com/support
Latviski ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst saistīto
Direktīvu būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem.
Pilns ES atbilstības paziņojuma teksts pieejams šeit: www.asus.com/support
Lietuvių „ASUSTeK Computer Inc.“ šiuo tvirtina, kad šis įrenginys atitinka
pagrindinius reikalavimus ir kitas svarbias susijusių direktyvų nuostatas. Visą
ES atitikties deklaracijos tekstą galima rasti: www.asus.com/support
Norsk ASUSTeK Computer Inc. erklærer herved at denne enheten er i
samsvar med hovedsaklige krav og andre relevante forskrifter i relaterte
direktiver. Fullstendig tekst for EU-samsvarserklæringen finnes på:
www.asus.com/support
Polski Firma ASUSTeK Computer Inc. niniejszym oświadcza, że
urządzenie to jest zgodne z zasadniczymi wymogami i innymi właściwymi
postanowieniami powiązanych dyrektyw. Pełny tekst deklaracji zgodności UE
jest dostępny pod adresem: www.asus.com/support
Português A ASUSTeK Computer Inc. declara que este dispositivo está em
conformidade com os requisitos essenciais e outras disposições relevantes
das Diretivas relacionadas. Texto integral da declaração da UE disponível em:
www.asus.com/support
A-8
Română ASUSTeK Computer Inc. declară că acest dispozitiv se conformează
cerinţelor esenţiale şi altor prevederi relevante ale directivelor conexe. Textul
complet al declaraţiei de conformitate a Uniunii Europene se găseşte la:
www.asus.com/support
Srpski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti
sa osnovnim zahtevima i drugim relevantnim odredbama povezanih
Direktiva. Pun tekst EU deklaracije o usaglašenosti je dostupan da adresi:
www.asus.com/support
Slovensky Spoločnosť ASUSTeK Computer Inc. týmto vyhlasuje, že toto
zariadenie vyhovuje základným požiadavkám a ostatým príslušným
ustanoveniam príslušných smerníc. Celý text vyhlásenia o zhode pre štáty EÚ
je dostupný na adrese: www.asus.com/support
Slovenščina ASUSTeK Computer Inc. izjavlja, da je ta naprava skladna z
bistvenimi zahtevami in drugimi ustreznimi določbami povezanih direktiv.
Celotno besedilo EU-izjave o skladnosti je na voljo na spletnem mestu:
www.asus.com/support
Español Por la presente, ASUSTeK Computer Inc. declara que este dispositivo
cumple los requisitos básicos y otras disposiciones pertinentes de las
directivas relacionadas. El texto completo de la declaración de la UE de
conformidad está disponible en: www.asus.com/support
Svenska ASUSTeK Computer Inc. förklarar härmed att denna
enhet överensstämmer med de grundläggande kraven och andra
relevanta föreskrifter i relaterade direktiv. Fulltext av EU-försäkran om
överensstämmelse finns på: www.asus.com/support
Українська ASUSTeK Computer Inc. заявляє, що цей пристрій відповідає
основним вимогам та іншим відповідним положенням відповідних
Директив. Повний текст декларації відповідності стандартам ЄС
доступний на: www.asus.com/support
Türkçe AsusTek Computer Inc., bu aygıtın temel gereksinimlerle ve ilişkili
Yönergelerin diğer ilgili koşullarıyla uyumlu olduğunu beyan eder. AB
uygunluk bildiriminin tam metni şu adreste bulunabilir:
www.asus.com/support
Bosanski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj usklađen
sa bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o usklađenosti dostupan je na: www.asus.com/support
Appendix
ASUS contact information
ASUSTeK COMPUTER INC.
Technical Support
Telephone Fax
Online support
4F, No. 150, Li-Te Road, Peitou, Taipei 112, Taiwan
+886-2-2894-3447
+886-2-2890-7798
www.asus.com
Appendix
Address
Telephone Fax Web site
+86-21-38429911
+86-21-5866-8722, ext. 9101#
http://qr.asus.com/techserv
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone+1-510-739-3777
Fax
+1-510-608-4555
Web site
http://www.asus.com/us/
Technical Support
Support fax
Telephone Online support
+1-812-284-0883
+1-812-282-2787
http://qr.asus.com/techserv
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, 40880 Ratingen, Germany
+49-2102-959931
http://www.asus.com/de
http://eu-rma.asus.com/sales
Technical Support
Telephone+49-2102-5789555
Support Fax
+49-2102-959911
Online support
http://qr.asus.com/techserv
ROG MAXIMUS X HERO
A-9
Appendix
DECLARATION OF CONFORMITY
Compliance Information Statement
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name:
Asus Computer International
800 Corporate Way, Fremont, CA 94539.
Address:
Phone/Fax No:
(510)739-3777/(510)608-4555
hereby declares that the product
Product Name : Motherboard
Model Number : ROG MAXIMUS X HERO,
ROG MAXIMUS X HERO(WI-FI AC)
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
A-10
Appendix