model g0602/g0752 10" x 22" benchtop lathe

MODEL G0602/G0752
10" X 22" BENCHTOP LATHE
OWNER'S MANUAL
(For models manufactured since 03/17)
G0602 Shown
COPYRIGHT © MARCH, 2013 BY GRIZZLY INDUSTRIAL, INC., REVISED APRIL, 2017 (JH)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL15556 PRINTED IN CHINA
V2.04.17
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 3
Machine Description....................................... 3
Contact Info.................................................... 3
Manual Accuracy............................................ 3
Model G0602 Identification............................. 4
Model G0752 Identification............................. 5
Controls & Components.................................. 6
Model G0602 Control Panel................................ 6
Model G0752 Control Panel................................ 6
Quick Change Gearbox....................................... 6
Carriage............................................................... 7
Tailstock............................................................... 7
Change Gears, Pulleys, V-Belt............................ 7
Machine Data Sheet....................................... 8
SECTION 1: SAFETY...................................... 10
Safety Instructions for Machinery................. 10
Additional Safety for Metal Lathes................ 12
Glossary of Terms........................................ 13
SECTION 2: POWER SUPPLY....................... 14
Availability.......................................................... 14
Full-Load Current Rating................................... 14
Circuit Requirements......................................... 14
Grounding & Plug Requirements....................... 15
Extension Cords................................................. 15
SECTION 3: SETUP........................................ 16
Unpacking..................................................... 16
Needed for Setup.......................................... 16
Inventory....................................................... 17
Cleanup......................................................... 18
Site Considerations....................................... 19
Lifting & Placing............................................ 20
Leveling & Mounting..................................... 21
Leveling.............................................................. 21
Mounting............................................................ 21
Assembly...................................................... 22
Lubricating Lathe.......................................... 22
Power Connection........................................ 22
Connecting Power.............................................. 22
Disconnecting Power......................................... 22
Test Run....................................................... 22
Spindle Break-In........................................... 24
Recommended Adjustments......................... 24
SECTION 4: OPERATIONS............................ 25
Operation Overview...................................... 25
Chuck & Faceplate Mounting....................... 26
Installation & Removal Devices.................... 26
Chuck Installation......................................... 27
Chuck Removal............................................ 28
Changing Jaw Set......................................... 28
Scroll Chuck Clamping................................. 29
4-Jaw Chuck................................................. 30
Faceplate...................................................... 31
Tailstock........................................................ 32
Positioning Tailstock.......................................... 32
Using Quill.......................................................... 32
Installing Tooling................................................ 32
Removing Tooling.............................................. 33
Offsetting Tailstock............................................ 33
Aligning Tailstock to Spindle Centerline............ 34
Centers......................................................... 36
Dead Centers..................................................... 36
Live Centers....................................................... 36
Mounting Dead Center in Spindle...................... 36
Removing Center from Spindle.......................... 37
Mounting Center in Tailstock............................. 37
Removing Center from Tailstock....................... 37
Mounting Workpiece Between Centers............. 38
Steady Rest.................................................. 38
Follow Rest................................................... 39
Carriage & Slide Locks................................. 39
Compound Rest............................................ 39
Four-Way Tool Post...................................... 40
Installing Tool..................................................... 40
Aligning Cutting Tool with Spindle Centerline.... 40
Manual Feed................................................. 41
Spindle Speed.............................................. 42
Determining Spindle Speed............................... 42
Setting Spindle Speed....................................... 42
G0602 Configuration Examples......................... 42
G0752 Configuration Example........................... 43
Power Feed.................................................. 44
Setting Power Feed Rate................................... 45
Threading...................................................... 46
Headstock Threading Controls.......................... 46
Apron Threading Controls.................................. 47
Thread Dial Chart.............................................. 47
SECTION 5: ACCESSORIES.......................... 49
SECTION 6: MAINTENANCE.......................... 51
Schedule....................................................... 51
Ongoing............................................................. 51
Daily, Before Operations.................................... 51
Daily, After Operations....................................... 51
Annually............................................................. 51
Cleaning/Protecting....................................... 51
Lubrication.................................................... 52
Quick-Change Gearbox..................................... 52
Ball Oilers........................................................... 53
Leadscrew & Carriage Rack.............................. 54
Bedways............................................................ 54
Compound Slide................................................ 54
Change Gears.................................................... 55
Machine Storage........................................... 56
SECTION 7: SERVICE.................................... 57
Troubleshooting............................................ 57
Operation........................................................... 58
Backlash Adjustment.................................... 60
Compound Rest................................................. 60
Cross Slide......................................................... 60
Gib Adjustment............................................. 61
Half Nut Adjustment...................................... 62
Leadscrew Shear Pin Replacement............. 62
V-Belt Tension & Replacement.................... 63
Tensioning V-Belt............................................... 63
Replacing V-Belt................................................ 64
Timing Belt Tension & Replacement............ 65
Tensioning Timing Belt...................................... 65
Replacing Timing Belt........................................ 65
SECTION 8: WIRING....................................... 66
Wiring Safety Instructions............................. 66
G0602 Wiring Diagram................................. 67
G0602 Electrical Components...................... 68
G0752 Wiring Box Diagram.......................... 69
G0752 Wiring Box Components................... 70
G0752 Control Panel Wiring Diagram.......... 71
G0752 Control Panel Components............... 72
G0752 Motor Wiring Diagram....................... 73
SECTION 9: PARTS........................................ 74
Spindle & Drive Belt...................................... 74
Apron............................................................ 76
Tool Post & Compound Rest........................ 77
Tailstock........................................................ 78
Bed & Leadscrew.......................................... 79
Steady Rest & Follow Rest........................... 80
G0602 Motor & Electrical.............................. 81
G0752 Motor & Electrical.............................. 82
Change Gears.............................................. 83
Gearbox........................................................ 84
Cross Slide & Carriage................................. 86
SECTION 10: APPENDIX................................ 89
G0602 Charts............................................... 89
G0752 Charts............................................... 90
WARRANTY AND RETURNS......................... 93
INTRODUCTION
Machine Description
Manual Accuracy
The metal lathe is used to remove material from
a rotating workpiece, which is held in place on
the spindle with a chuck or faceplate. The cutting
tool is mounted on the carriage or tailstock and
moved against the spinning workpiece to perform
the cut.
We are proud to provide a high-quality owner’s
manual with your new machine!
Typical metal lathe cutting operations include facing, turning, parting, drilling, reaming, grooving,
knurling, and threading. There are a wide variety
of tools and workpiece holding devices available
for each of these operations.
Models G0602 and G0752 both require setting
gearbox dial positions and positioning V-belts to
select the spindle speed. However, the Model
G0752 features an electronic variable-speed control and digital RPM display that make it possible
to select speeds within the selected range while
the machine is running.
Contact Info
We stand behind our machines! If you have questions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number and manufacture date from the
machine ID label. This will help us help you faster.
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: (570) 546-9663
Email: techsupport@grizzly.com
We made every effort to be exact with the instructions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that sometimes the machine you receive is
slightly different than shown in the manual.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something, check our
website for an updated version. We post current
manuals and manual updates for free on our website at www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the Manufacture Date and Serial Number from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documentation is available for your machine.
Manufacture Date
Serial Number
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
Model G0602/G0752 (Mfd. Since 03/17)
-3-
Model G0602 Identification
C
D
E
F
G
H
B
I
J
A
K
L
U
T
S
R
Q
P
O
N
M
Figure 1. G0602 identification.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
Emergency Stop Button
Spindle Direction Switch
ON Button
3-Jaw Chuck
Steady Rest
4-Way Tool Post
Follow Rest
Compound Rest Handwheel
MT#3 Dead Center
Tailstock
Back Splash
Serious personal injury could occur if
you connect the machine to power before
completing the setup process. DO NOT
connect power until instructed to do so
later in this manual.
-4-
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
Chip Tray
Thread Dial
Half Nut Lever
Cross Slide Handwheel
Carriage Handwheel
Leadscrew
Alpha Gearbox Dial
Gearbox Oil Level Sight Glass
Numeric Gearbox Dial
Change Gear and Belt Safety Cover
Untrained users have an increased risk
of seriously injuring themselves with this
machine. Do not operate this machine until
you have understood this entire manual
and received proper training.
Model G0602/G0752 (Mfd. Since 03/17)
Model G0752 Identification
G
D
C
E
H
F
I
L
J
K
B
N
M
A
X
W
V
U
T
S
P
R
O
Q
Figure 2. G0752 identification.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Emergency Stop Button
ON Button
OFF Button
Spindle Speed RPM Display
Spindle Speed Dial
Spindle Direction Switch
3-Jaw Chuck
Steady Rest
4-Way Tool Post
Follow Rest
Compound Rest Handwheel
MT#3 Dead Center
Serious personal injury could occur if
you connect the machine to power before
completing the setup process. DO NOT
connect power until instructed to do so
later in this manual.
Model G0602/G0752 (Mfd. Since 03/17)
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Tailstock
Back Splash
Chip Tray
Thread Dial
Half Nut Lever
Cross Slide Handwheel
Carriage Handwheel
Leadscrew
Alpha Gearbox Dial
Gearbox Oil Level Sight Glass
Numeric Gearbox Dial
Change Gear and Belt Safety Cover
Untrained users have an increased risk
of seriously injuring themselves with this
machine. Do not operate this machine until
you have understood this entire manual
and received proper training.
-5-
Controls &
Components
Refer to Figures 3–8 and the following descriptions to become familiar with the basic controls of
this lathe.
D. OFF Button: Stops spindle rotation.
E. Spindle Speed RPM Display: Shows a digital readout of the spindle speed.
F. Spindle Speed Dial: Controls the variable
spindle speed.
Quick Change Gearbox
Model G0602 Control Panel
B
A
C
G
H
Figure 5. Gearbox dials.
Figure 3. Model G0602 control panel.
Model G0752 Control Panel
E
F
A
B
C
G. Numeric Gearbox Dial: Controls the
leadscrew for threading and feeding operations. To make a selection, rotate the dial to
the corresponding number displayed on the
threading or feed charts.
H. Alpha Gearbox Dial: Controls the leadscrew
for threading and feeding operations. To
make a selection, rotate the dial to the corresponding letter displayed on the threading
or feed charts.
D
Figure 4. Model G0752 control panel.
A. Emergency STOP Button: Cuts power to
the motor and control panel when pressed.
Remains depressed until reset by twisting
clockwise.
B. Spindle Switch: Starts, stops, and reverses
spindle rotation.
C. ON Button: Enables spindle rotation.
-6-
Model G0602/G0752 (Mfd. Since 03/17)
Carriage
Tailstock
I
R
Q
J
S
T
K
L
U
V
Figure 7. Tailstock controls.
P
O
N
M
Figure 6. Carriage controls.
I. 4-Way Tool Post: Holds up to four cutting
tools at once that can be individually indexed
to the workpiece.
J. Compound Rest Handwheel: Moves the
tool toward and away from the workpiece at
the preset angle of the compound rest.
T. Tailstock Quill Handwheel: Controls the
movement of the quill.
U. Offset Scale: Indicates the relative distance
of tailstock offset from the spindle centerline.
V. Tailstock Offset Set Screw (1 of 2): Adjusts
the tailstock offset left or right from the spindle centerline.
Change Gears, Pulleys, V-Belt
K. Carriage Lock: Secures the carriage for
greater rigidity when it should not move.
W. Change Gears: The configuration of the
change gears for power feed, inch, and metric threading controls the leadscrew speed.
L. Thread Dial: Indicates when to engage the
half nut during threading operations.
X.Pulleys: The position of the V-belt on the pulleys controls the spindle speed.
M. Half Nut Lever: Engages/disengages half
nut for power feed and threading operations.
Y. V-Belt: Transfers power from the motor pulley to the spindle pulley. Model G0602 uses
two V-belts. Model G0752 uses one V-belt.
N. Thread Chart: Indicates which thread dial
mark to use when engaging the half nut for
specific inch thread pitches.
Z.Timing-Belt: (G0602) Transfers power from
the motor to the secondary drive pulley.
O. Cross Slide Handwheel: Moves the cross
slide toward and away from the workpiece.
P. Carriage Handwheel: Moves the carriage
along the bedway.
Q. Tailstock Quill: Moves a tool or center
mounted in the tailstock toward or away from
the workpiece.
W
Z
X
R. Tailstock Quill Lock Lever: Secures the
quill position.
Y
S. Tailstock Lock Nut: Secures the tailstock to
the bedway.
Figure 8. Change gears and pulleys
(Model G0602 shown).
Model G0602/G0752 (Mfd. Since 03/17)
-7-
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0602, G0752
10" x 22" Bench Top Metal Lathe
Model Number
G0602
G0752
Product Dimensions
Weight
Width/Depth/Height
330 lbs.
46" x 22" x 16 ⁄8"
50 1⁄2" x 22" x 195⁄8"
5
Foot Print (Width/Depth)
471⁄2" x 121⁄2"
Shipping Dimensions
Type
Wood Crate
Content
Weight
Machine
432 lbs.
453 lbs.
Width /Depth/Height
55" x 23" x 22"
Electrical
Power Requirement
Minimum Circuit Size
110V, Single-Phase, 60 Hz
20A
Switch
15A
Forward & Reverse Button Switches
Cord Length
Cord Gauge
5 ft.
16 AWG
16 AWG
Plug Included
Yes
Included Plug Type
NEMA 5-15
Main Motor
Type
Horsepower
TEFC Capacitor-Start Induction
TEFC Induction
1 HP
1 HP
Phase
Single-Phase
3-Phase
Amps
13.6A
12A
Speed
Power Transfer
Bearings
1725 RPM
Cogged Belt Drive
Shielded & Permanently Sealed
Operation Information
Swing Over Bed
95⁄8"
Distance Between Centers
22 in.
Swing Over Cross Slide
61⁄8 in.
Swing Over Saddle
61⁄8 in.
Maximum Tool Bit Size
Compound Travel
⁄2 in.
1
31⁄2
Carriage Travel
181⁄2 in.
Cross Slide Travel
61⁄2 in.
-8-
Model G0602/G0752 (Mfd. Since 03/17)
Model Number
G0602
G0752
Headstock Information
Spindle Bore
1"
Spindle Size
13⁄4"
Spindle Taper
MT#4
Spindle Threads
8 TPI
Number of Spindle Speeds
Range of Spindle Speeds
Spindle Type
Spindle Bearings
6
Variable
150 – 2400 RPM
100 – 800, 160 – 1300, 250 – 2000 RPM
Threaded
Tapered Roller
Tailstock Information
Tailstock Quill Travel
21⁄2"
Tailstock Taper
MT#3
Tailstock Barrel Diameter
1.25"
Threading Information
Number of Longitudinal Feeds
Range of Longitudinal Feeds
9
0.0025 – 0.0140 in./rev.
Number of Inch Threads
Range of Inch Threads
33
8 – 72 TPI
Number of Metric Threads
Range of Metric Threads
26
0.25 – 3.50 mm
Dimensions
Bed Width
61⁄8 in.
⁄4 in.
Leadscrew Diameter
Leadscrew TPI
3
12 TPI
Leadscrew Length
34"
Steady Rest Capacity
1
⁄4"– 2"
Follow Rest Capacity
1
⁄4"– 2"
Faceplate Size
8 in.
Construction
Base
Cast Iron
Headstock
Cast Iron
Headstock Gears
Bed
Steel
Hardened and Precision-Ground Cast Iron
Stand
Cast Iron
Paint
Epoxy
Other
Country of Origin
Warranty
Serial Number Location
Approximate Assembly & Setup
Time
Model G0602/G0752 (Mfd. Since 03/17)
China
1 Year
ID Label on Headstock
1 Hour
-9-
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
NOTICE
This symbol is used to alert the user to useful information about
proper operation of the machine.
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, disconnect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machinery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-10-
ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
Model G0602/G0752 (Mfd. Since 03/17)
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hearing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifications—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
Model G0602/G0752 (Mfd. Since 03/17)
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intended operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
-11-
Additional Safety for Metal Lathes
Serious injury or death can occur from getting entangled in, crushed between, or struck by
rotating parts on a lathe! Unsecured tools or workpieces that fly loose from rotating objects
can also strike nearby operators with deadly force. To minimize the risk of getting hurt or killed,
anyone operating this machine MUST completely heed the hazards and warnings below.
CLOTHING, JEWELRY & LONG HAIR. Tie back
long hair, remove jewelry, and do not wear loose
clothing or gloves. These can easily get caught on
rotating parts and pull you into lathe.
SECURE WORKPIECE. An improperly secured
workpiece can fly off spindle with deadly force.
Make sure workpiece is properly secured before
starting the lathe.
ROTATING PARTS. Always keep hands and body
at a safe distance from rotating parts—especially
those with projecting surfaces. Never hold anything against rotating workpiece, such as emery
cloth, that can pull you into lathe.
CHUCKS. Chucks can be heavy and difficult to
hold. During installation and removal, protect your
hands and precision bed ways by using a chuck
cradle or piece of plywood over the bed ways. Use
lifting equipment, as necessary, for large chucks.
GUARDING. Guards and covers protect against
entanglement or flying objects. Always ensure they
are properly installed while machine is running.
STOPPING SPINDLE. Always allow spindle to
completely stop on its own, or use a brake, if
provided. Never put hands or another object on a
spinning workpiece to make it stop faster.
ADJUSTMENT TOOLS. Remove all chuck keys,
wrenches, and adjustment tools before turning
lathe ON. A tool left on the lathe can become a
deadly projectile when spindle is started.
SAFE CLEARANCES. Before starting spindle,
verify workpiece has adequate clearance by handrotating it through its entire range of motion.
NEW SETUPS. Test each new setup by starting
spindle rotation at the lowest speed and standing
to the side of the lathe until workpiece reaches full
speed and you can verify safe rotation.
SPINDLE SPEEDS. Using spindle speeds that are
too fast for the workpiece or clamping equipment
can cause rotating parts to come loose and strike
nearby people with deadly force. Always use slow
spindle speeds with large or non-concentric workpieces. Never exceed rated RPM of the chuck.
LONG STOCK SAFETY. Long stock can whip
violently if not properly supported. Always support
any stock that extends from the chuck/headstock
more than three times its own diameter.
CLEARING CHIPS. Metal chips can be razor
sharp. Avoid clearing them by hand or with a rag.
Use a brush or vacuum instead.
-12-
CRASHING. A serious explosion of metal parts
can occur if cutting tool or other lathe component
hits rotating chuck or a projecting part of workpiece. Resulting metal fragments can strike nearby
people and lathe will be seriously damaged. To
reduce risk of crashing, ALWAYS release automatic feeds after use, NEVER leave lathe unattended,
and CHECK all clearances before starting lathe.
COOLANT SAFETY. Coolant can become very
toxic through prolonged use and aging. To minimize toxicity, change coolant regularly. When
using, position nozzle properly to avoid splashing
operator or causing a slipping hazard on floor.
TOOL SELECTION. Cutting with incorrect or dull
tooling increases risk of injury from broken or dislodged components, or as a result of extra force
required for operation. Always use sharp tooling
that is right for the job.
SANDING/POLISHING. To reduce risk of entanglement, never wrap emery cloth around rotating
workpiece. Instead, use emery cloth with the aid
of a tool or backing board.
MEASURING WORKPIECE. To reduce risk of
entanglement, never measure rotating workpieces.
Model G0602/G0752 (Mfd. Since 03/17)
Glossary of Terms
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this lathe and metalworking in general. Become familiar with these terms for assembling, adjusting or
operating this machine. Your safety is VERY important to us at Grizzly!
Arbor: A machine shaft that supports a cutting
tool.
Backlash: Wear in a screw or gear mechanism
that may result in slippage, vibration, and loss
of tolerance.
Carriage: A main housing that consists of the
apron and the saddle.
Cross Slide: A fixture attached to the lathe carriage that holds the compound rest and can be
moved in and out.
Compound Rest: A fixture attached to the cross
slide that holds the tool holder and can be
moved in and out.
Cutting Speed: The distance a point on a cutter
moves in one minute, expressed in meters or
feet per minute.
Dial Indicator: An instrument used in setup
and inspection work that shows on a dial the
amount of error in size or alignment of a part.
Facing: In lathe work, cutting across the end of
a workpiece, usually to machine a flat surface.
Feed: The movement of a cutting tool into a
workpiece.
Lathe Center: A lathe accessory with a 60°
point which is inserted into the headstock or
tailstock of the lathe and is used to support the
workpiece.
Leadscrew: Lathe—The long screw that is driven by the change gears and supplies power to
the carriage.
Saddle: The upper portion of carriage that rides
on the lathe ways and supports the cross feed
and the follow rest.
Spindle: The revolving shaft that holds and
drives the workpiece or cutting tool.
Tailstock: A moveable fixture opposite of the
headstock on a lathe that has a spindle used
to support one end of a workpiece and for holding tools.
Tool Post: The part of the compound rest that
holds the tool holder.
Turret: Lathe—A machine fixture that holds multiple tools and can be revolved and indexed to
position.
Ways: The precision machined and flat tracks
on a lathe on which the carriage and tailstock
slide.
Fixture: A device that securely holds the
workpiece in place during cutting operation
as opposed to a jig which is used to hold and
guide a workpiece through an operation.
Gib: A tapered wedge located along a sliding
member to take up wear or to ensure a proper
fit.
Headstock: The major lathe component that
houses the spindle and motor drive system to
turn the workpiece.
Model G0602/G0752 (Mfd. Since 03/17)
-13-
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the availability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
G0602 Full-Load Rating............................13.6A
G0752 Full-Load Rating...............................12A
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid overloading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
-14-
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
110V Circuit Requirements
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage................................ 110V/120V
Cycle...........................................................60 Hz
Phase............................................ Single-Phase
Minimum Circuit Size (G0602)........... 20 Amps
Minimum Circuit Size (G0752)........... 15 Amps
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power supply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, consult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
Model G0602/G0752 (Mfd. Since 03/17)
Grounding & Plug Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!
GROUNDED
5-15 RECEPTACLE
Grounding Prong
5-15 PLUG
Neutral Hot
Figure 9. Included 5-15 plug and receptacle.
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is necessary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size............................14 AWG
Maximum Length (Shorter is Better).......50 ft.
SHOCK HAZARD!
Two-prong outlets do not meet the grounding
requirements for this machine. Do not modify
or use an adapter on the plug provided—if
it will not fit the outlet, have a qualified
electrician install the proper outlet with a
verified ground.
Model G0602/G0752 (Mfd. Since 03/17)
-15-
SECTION 3: SETUP
Unpacking
Needed for Setup
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage. If items are damaged,
please call us immediately at (570) 546-9663.
The following are needed to complete the setup
process, but are not included with your machine.
IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original packaging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
DescriptionQty
• Additional People........................................ 1
• Safety Glasses................ 1 For Each Person
• Cleaner/Degreaser (Page 18)..... As Needed
• Quality Metal Protectant.............. As Needed
• Disposable Shop Rags................ As Needed
• Precision Level............................................ 1
• Lifting Straps (rated for at least 500 lbs.).... 2
• Forklift/Power Lifting Device (rated for at least
500 lbs.)....................................................... 1
• Bench Mounting Hardware......... As Needed
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
-16-
Model G0602/G0752 (Mfd. Since 03/17)
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Installed Components (Figure 10)
Qty.
A. 5" Three-Jaw Chuck.................................... 1
B. Steady Rest................................................. 1
C. Follow Rest.................................................. 1
D. 4-Way Tool Post.......................................... 1
E. Compound Rest.......................................... 1
F. Tailstock....................................................... 1
A
B
C
D
E
V.
W.
X.
Dead Center MT#4...................................... 1
Change Gear Set........................................ 1
— Change Gear (27-tooth, Installed).......... 1
— Change Gear (36-tooth).......................... 1
— Change Gear (40-tooth).......................... 1
— Change Gear (44-tooth).......................... 1
— Change Gear (45-tooth).......................... 1
— Change Gear (46-tooth).......................... 1
— Change Gear (48-tooth).......................... 1
— Change Gear (52-tooth).......................... 1
— Change Gear (56-tooth, Installed).......... 1
— Change Gear (60-tooth).......................... 1
— Plastic Drive Gear (60-tooth, Installed)... 1
— Change Gear (104-tooth, Installed)........ 1
— Change Gear (120-tooth)........................ 1
— Change Gear (127-tooth, Installed)......... 1
Frequency Drive Manual VFD-E (G0752, Not Shown)........................................................ 1
H
J
F
K
I
L
M
N
O
Figure 10. Installed components.
Packaged Components (Figure 11)
Qty.
G. Chip Pan (Not Shown)................................. 1
H. Hex Wrench Set (2.5, 3, 4, 5, 6 mm)......1 Ea
I. Toolbox........................................................ 1
J. 8" Faceplate................................................ 1
K. 61⁄2" 4-Jaw Independent Chuck................... 1
L. Low Range Belt 271⁄ 2" (G0602)................... 1
High Range Belt 33" (Installed, G0602)...... 1
V-Belt 33" (Installed, G0752)....................... 1
M. #2 Phillips and Standard Screwdriver....1 Ea
N. Wrench Set (8/10, 12/14, 19/17mm)........1 Ea
O. 3-Jaw Chuck Internal Jaw Set..................... 1
P. 3-Jaw Chuck Key........................................ 1
Q 4-Jaw Chuck Key........................................ 1
R. Oil Bottle for Oil........................................... 1
S. Cross Slide Handwheel Handle.................. 1
T. Carriage Handwheel Handle....................... 1
U. Dead Centers MT#3 ................................... 2
Model G0602/G0752 (Mfd. Since 03/17)
S
T
U
Q
P
R
V
W
Figure 11. Packaged components.
NOTICE
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
-17-
Cleanup
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preventative, but the following steps work well in a wide
variety of situations. Always follow the manufacturer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
•
Disposable rags
•
Cleaner/degreaser (WD•40 works well)
•
Safety glasses & disposable gloves
•
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/degreaser is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-18-
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avo i d
u sing t h e s e p r o d u c t s
to c l e a n m a c hin e r y.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
T23692—Orange Power Degreaser
A great product for removing the waxy shipping
grease from your machine during clean up.
Figure 12. T23692 Orange Power Degreaser.
Model G0602/G0752 (Mfd. Since 03/17)
Site Considerations
Weight Load
Physical Environment
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
The physical environment where the machine is
operated is important for safe operation and longevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20%–95% (non-condensing); or
the environment is subject to vibration, shocks,
or bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the maintenance and service described in this manual.
See below for required space allocation.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals, or
other hazards. Make sure to leave enough space
around machine to disconnect power supply or
apply a lockout/tagout device, if required.
Lighting
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Wall
Min. 30"
for Maintenance
65"
110V
Supply
18"
Access
Door
Lathe
Keep
Workpiece
Loading Area
Unobstructed
12.5"
30"
Footprint
47.5"
Footprint
Figure 13. Minimum working clearances.
Model G0602/G0752 (Mfd. Since 03/17)
-19-
Lifting & Placing
5. Wrap the lifting straps around the bed and
between the leadscrew and the bedway, as
shown in Figure 14, to help prevent bending
the leadscrew during lifting.
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.
Do not attempt to lift or move this lathe without
using the proper lifting equipment (such as forklift
or crane) or the necessary assistance from other
people. Refer to Needed for Setup on Page 16
for details.
To lift and move the lathe:
1. Remove the shipping crate top and sides,
then remove the chip pan, 4-jaw chuck, faceplate, and toolbox from the shipping pallet.
Figure 14. Example of lifting strap positions.
6. Attach the lifting straps to the power lifting
equipment, have an assistant steady the
load, then lift it just enough to clear any
obstacles and move it to its mounting position.
7. Properly mount the lathe as instructed in the
Mounting subsection on Page 21.
2. Position the chip pan on the selected mounting surface and use it as a template to mark
the hole locations for the mounting hardware
(refer to Leveling & Mounting on Page 21).
3. Unbolt the lathe from the shipping pallet.
Only use lifting straps and power lifting
equipment rated for at least 500 lbs. and in
good working condition. If the lathe falls or
tips over while moving it, serious personal
injury and property damage could result.
4. To balance the load for lifting, move the
tailstock and carriage to the extreme right
end of the bedway, then lock them in place.
Note: Before attempting to move the carriage, make sure the carriage lock is loose
and the half nut is disengaged.
-20-
Model G0602/G0752 (Mfd. Since 03/17)
Leveling & Mounting
For accurate turning results and to prevent
warping the cast iron bed and ways, the lathe
bedways MUST be leveled from side-to-side
and from front-to-back on both ends.
Re-check the bedways 24 hours after
installation, two weeks after that, and then
annually to make sure they remain level.
Mounting
The chip pan and the base of the lathe have
holes that allow the machine to be mounted to
a workbench. You MUST mount your machine
to a workbench to prevent it from unexpectedly
moving during operation, which could lead to
personal injury or property damage.
Follow these guidelines when mounting your
lathe to ensure safe and accurate cutting
results:
•
Make sure that the workbench can adequately support the weight of the machine and
materials and that it will not move or vibrate
during operation.
•
Use a silicon sealant between the lathe and
the chip pan to prevent coolant or other fluids
from leaking through onto the bench or floor.
Leveling
Leveling machinery helps precision components,
such as bedways, remain straight and flat during
the lifespan of the machine. Components on a
machine that is not level may slowly twist due to
the dynamic loads placed on the machine during
operation.
For best results, use a precision level that is at
least 12" long and sensitive enough to show a
distinct movement when a 0.003" shim (approximately the thickness of one sheet of standard
newspaper) is placed under one end of the level.
See the figure below for an example of a high
precision level.
To mount the lathe and chip pan to the workbench,
drill holes all the way through the workbench, and
use hex bolts, washers, and hex nuts to secure
the lathe to the workbench, as illustrated in
Figure 16.
Hex Nut
Lock Washer
Flat Washer
Lathe
Silicon
Chip Pan
Workbench
Flat Washer
Hex Bolt
Figure 16. Example of a through mount setup.
Figure 15. Grizzly Model H2683 12" Master
Machinist's Level.
Model G0602/G0752 (Mfd. Since 03/17)
-21-
Assembly
Power Connection
With the exception of the handwheel handles, the
lathe is shipped fully assembled.
Before the machine can be connected to the
power source, an electrical circuit and connection device must be prepared per the POWER
SUPPLY section in this manual, and all previous setup instructions in this manual must be
completed to ensure that the machine has been
assembled and installed properly.
To install the handwheel handles, thread the large
handle into the carriage handwheel and the small
handle into the cross slide handwheel, as shown
in Figure 17.
Connecting Power
Always make sure the spindle direction switch on
the front of the headstock is turned OFF (middle
position) before connecting power.
Small
Handle
Insert the power cord plug into a matching power
supply receptacle.
Large
Handle
Disconnecting Power
Figure 17. Handwheel handles installed.
If you need to disconnect the machine from power
for maintenance, service, or adjustments, turn the
machine off and pull the plug completely out of
the receptacle.
Lubricating Lathe
Test Run
GEARBOX MUST
BE FILLED WITH OIL!
LATHE MAY NOT
HAVE OIL INCLUDED!
Refer to the Lubrication
Section in this Manual
for Recommended
Oil Type.
The lathe must be properly lubricated before it can
be operated for the first time.
Once the assembly is complete, test run your
machine to make sure it runs properly and is
ready for regular operation.
The test run consist of verifying the following: 1)
The motor powers up and runs correctly, 2) the
emergency STOP button safety feature works
correctly.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review
Troubleshooting on Page 57.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
Damage caused to the bearings and gears from
running the lathe without oil in the reservoirs
will not be covered under warranty. Refer to the
Lubrication section, beginning on Page 52, for
details on how to lubricate the lathe.
-22-
Model G0602/G0752 (Mfd. Since 03/17)
To test run your machine:
Half Nut
Lever
1. Make sure the spindle direction switch (see
Figure 18) is turned to STOP, and press the
emergency STOP button.
Disengaged
Emergency
Stop Button
Halfnut
Lever
ON
Button
Engaged
Spindle Direction Switch
Pointing to STOP
Figure 18. Headstock and gearbox controls.
2. Read and follow the safety instructions at the
beginning of the manual, take all required
safety precautions, and make sure all previous preparation steps discussed in this
manual have been followed and completed.
Figure 19. Half nut lever in the disengaged
position.
7. Reset the emergency STOP button by twisting it clockwise until it pops out.
8. G0752 Only: Ensure the spindle speed dial is
turned all the way counterclockwise. Push the green ON button, then turn the
spindle direction switch to FWD. Turn the
spindle speed dial until the spindle speed
display shows 150 RPM. The spindle should
be rotating counterclockwise—down and
toward you as you face the lathe.
G0602: Push the green ON button, then turn
the spindle direction switch to FWD. The
spindle should be rotating counterclockwise—
down and toward you as you face the lathe.
3. Clear away all tools and objects used during
assembly, lubrication, and preparation.
4. Make sure chuck and jaws, if installed, are
secure (see Chuck Installation on Page 27).
Note: If a chuck is not installed on the lathe,
you do not need to install one for this test.
5. Set lathe spindle speed for 150 RPM, (refer
to Setting Spindle Speed on Page 42).
6. Disengage the half nut with the lever shown
in Figure 19.
9. Push the emergency STOP button to turn the
lathe OFF, then, without resetting the STOP
button, try to restart spindle rotation. The
spindle should not start.
—If spindle rotation does start with the
emergency STOP button pressed in, the
button is not operating correctly. This
safety feature must operate properly
before continuing operation. Use the
spindle direction switch to stop the lathe,
disconnect it from power, and call Tech
Support for help.
Congratulations! The test run is complete. Turn
the lathe OFF and perform the following Spindle
Break-In procedure.
Model G0602/G0752 (Mfd. Since 03/17)
-23-
Spindle Break-In
Before subjecting the lathe to full loads, it is essential to complete the spindle break-in process. This
will ensure the best results and maximum life of
the precision components inside the lathe.
The break-in procedure must be performed in
succession with the Test Run procedure because
many of the test run steps prepare the lathe controls for the break-in process.
Important: Do not perform the break-in procedure
independently from the Test Run section—serious damage could occur to the lathe if the controls
are set differently than instructed in that section.
To perform the spindle break-in:
Recommended
Adjustments
For your convenience, the adjustments listed
below have been performed at the factory.
However, because of the many variables involved
with shipping, we recommend that you at least
verify the following adjustments to ensure the best
possible results from your new machine. Stepby-step instructions for these adjustments can be
found on the pages referenced below.
Factory adjustments that should be verified:
•
•
•
Tailstock alignment (Page 33)
Gib adjustments (Page 61)
Backlash adjustment (Page 60)
1. Operate the lathe at 150 RPM for 10 minutes.
2. G0602: Repeat Step 1 at each of the following
speeds 300, 560, 720, 1200, and 2400.
G0752: Repeat Step 1 at each of the following
approximate speeds: 800, 1300, and 2000.
3. When the spindle has come to a complete
stop, run the spindle in reverse at 2400 RPM
(Model G0602) or 2000 RPM (Model G0752)
for another 10 minutes, then press the
emergency STOP button and DISCONNECT
THE LATHE FROM POWER!
4. Check, and if necessary, re-tension the drive
belts (refer to V-Belt Tension & Replacement
Page 64 on page for detailed instructions.)
5. While the oil is still warm and any metal particles are still suspended in the oil, change
the gearbox oil (refer to Lubrication on Page
52 for detailed instructions).
Congratulations! The spindle break-in is complete. Continue with the following Recommended
Adjustments subsection.
-24-
Model G0602/G0752 (Mfd. Since 03/17)
SECTION 4: OPERATIONS
Operation Overview
The purpose of this overview is to provide the novice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual, seek additional training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.
To complete a typical operation, the operator
does the following:
1. Puts on safety glasses, rolls up sleeves,
removes jewelry, and secures any clothing,
jewelry, or hair that could get entangled in
moving parts.
2. Examines the workpiece to make sure it is
suitable for turning, then securely mounts the
workpiece in a chuck, between centers, or on
the faceplate.
3. Mounts the tooling, aligns it with the workpiece,
then backs it away to establish a safe startup
clearance.
4. Clears all setup tools from the lathe.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
5. Checks for safe clearances by rotating the
workpiece by hand at least one full revolution.
6. Sets the correct spindle speed for the operation.
7. If using power feed, selects the proper feed
rate for the operation.
To reduce risk of eye injury
from flying chips always
wear safety glasses or face
shield when operating.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
8. Starts spindle rotation, then engages the half
nut.
9. Uses various carriage controls to move the
tooling into the workpiece for operations.
10. When finished cutting, disengages the half
nut (power feed only), moves the spindle
direction switch to the OFF position, waits for
the spindle to completely stop, then removes
the workpiece.
Complete the Test Run & Break-In procedure on Pages 22– 24 before using this lathe
for any cutting or threading operations; otherwise, gear box damage will occur.
Model G0602/G0752 (Mfd. Since 03/17)
-25-
Chuck & Faceplate
Mounting
Installation &
Removal Devices
This lathe is equipped with a threaded spindle
nose. With this type of spindle, a chuck or faceplate is screwed directly onto the spindle nose.
Because chucks are heavy and often awkward to
hold, some kind of support or protective device
should be used during installation or removal. The
weight and size of the chuck will determine the
appropriate device to use (refer to the following
figure for examples).
Never use spindle speeds faster than the
chuck RPM rating or the safe limits of
your workpiece. Excessive spindle speeds
greatly increase the risk of the workpiece or
chuck being thrown from the machine with
deadly force!
Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious personal injury.
Keep these items away
from moving parts at all
times to reduce this risk.
This lathe ships with the 3-jaw chuck installed.
This is a scroll-type chuck where all three jaws
move in unison when the chuck key is used.
The included 4-jaw chuck features independent
jaws, which are used for square or unevenlyshaped stock, and to mount work that needs to be
adjusted to near zero total indicated runout.
If neither chuck can hold your workpiece, the
cast iron faceplate has slots for T-bolts that hold
standard or custom clamping hardware. With the
correct clamping hardware, a faceplate offers a
wide range of uses, including machining nonconcentric workpieces, straight turning between
centers, off-center turning, and boring.
-26-
A dropped chuck can cause amputation,
serious crushing injuries, or property damage. Always use a support or protective
device to reduce this risk when installing or
removing a chuck.
SMALL, LIGHTWEIGHT CHUCKS
Plywood Protection
Plate for Chucks
Installed by Hand
MEDIUM-SIZE, HEAVY CHUCKS
Plywood & 2x4
Chuck Cradle
Solid Block
Chuck Cradle
Way Slot
Jaw Slot
Plywood Chuck Cradle
(Straight Cuts)
Plywood Chuck Cradle
(Curved Cuts)
LARGE,
VERYof
HEAVY
CHUCKS
Figure 20.
Examples
common
devices used
installation
and
removal.
Fabricated Steel
during chuck
Pre-Threaded
Hole
for Lifting Eye
Lifting Hook
Model G0602/G0752 (Mfd. Since 03/17)
Chuck Installation
5. Insert the chuck wrenches as shown in
Figure 22, and tighten the chuck until it is
seated snug against the spindle shoulder.
To ensure accurate work, it is extremely important
to make sure the spindle nose and chuck mating
surfaces are clean. Even a small amount of lint or
debris can affect accuracy.
The chuck is properly installed when it threads
all the way onto the spindle nose (see Figure 21
below) and is seated against the spindle shoulder.
Spindle
Shoulder
Threads
Inside
Taper
Figure 21. Spindle nose.
Figure 22. Location to insert chuck keys when
installing chuck.
6. Install the chuck locks with the cap screws
(see Figure 23).
Tools Needed:
Qty
Chuck Wrenches................................................ 2
Hex Wrench 5mm............................................... 1
To install the chuck:
1. DISCONNECT LATHE FROM POWER!
2. Use an appropriate device to protect the ways
and support the chuck during the installation
process (refer to Installation & Removal
Devices on Page 26).
3. Thoroughly clean, inspect, deburr, and lightly
oil all threads and mating surfaces.
Cap Screw
Chuck Lock
Figure 23. Chuck lock installed on spindle nose
and chuck.
4. Thread the chuck onto the spindle nose and
hand-tighten it.
Model G0602/G0752 (Mfd. Since 03/17)
-27-
Chuck Removal
Changing Jaw Set
Tools Needed:
Qty
Chuck Wrenches................................................ 2
Hex Wrench 5mm............................................... 1
Tools Needed:
Qty
Chuck Wrench.................................................... 1
To remove the chuck:
1. DISCONNECT LATHE FROM POWER!
2. Use an appropriate device to protect the ways
and support the chuck (refer to Installation &
Removal Devices on Page 26).
3. Remove the cap screws and chuck locks
(see Figure 24).
The 3-jaw scroll chuck included with the lathe features inside and outside hardened steel jaw sets
(see Figure 26), which move in unison to center
a concentric workpiece.
When installing the jaws, it is important to make
sure they are installed correctly. Incorrect installation will result in jaws that do not converge evenly
and are unable to securely clamp a workpiece.
Inside
Set
Cap Screw
Outside
Set
Chuck Lock
Figure 24. Location of chuck lock and cap
screws.
4. Insert the chuck wrenches, as shown in
Figure 25, then while holding the spindle,
unthread the chuck in a counterclockwise
direction.
Figure 26. Chuck and jaw selection.
Jaws are numbered from 1–3 (see Figure 27).
They are designed to be installed in numerical
order in the jaw guides so they will hold a concentric workpiece evenly.
Jaw
Guides
Jaw Numbers
Insert Keys
Here
Figure 25. Location to insert chuck keys when
removing chuck.
5. Support the chuck, unscrew it, and remove.
-28-
Figure 27. Jaw guide and jaw numbers.
Model G0602/G0752 (Mfd. Since 03/17)
To change the jaw set:
1. DISCONNECT LATHE FROM POWER!
2. Place a piece of plywood over the bedways to
protect them from potential damage.
3. Insert the chuck key and turn it counterclockwise to back the jaws out and remove them.
4. Use mineral spirits to clean the debris and
grime from the jaws and chuck jaw guides.
5. Apply a thin coat of white lithium grease to
the surfaces of the removed jaw set. Store
in a safe place free from moisture and abrasives.
6. Rotate the chuck key clockwise until you see
the tip of the scroll-gear lead thread just begin
to enter a jaw guide (see Figure 28).
Scroll Chuck
Clamping
The 3-jaw scroll-type chuck has an internal
scroll-gear that moves all jaws in unison when
adjusted with the chuck key. The chuck will hold
cylindrical parts on-center with the axis of spindle
rotation and can be rotated at high speeds if the
workpiece is properly clamped and balanced.
Never mix jaw types or positions to
accommodate an odd-shaped workpiece. The
chuck will spin out of balance and may throw
the workpiece! Instead, use an independent jaw
chuck or a faceplate.
Insufficient
Jaw Clamping
Safer Inside
Jaw Use
Unstable
Workpiece
Bar Stock
CORRECT
Lead Thread
Safer Outside
Jaw Use
Shallow
Bar Stock
Figure 28. Lead thread on scroll gear.
7. Insert jaw #1 into the jaw guide and hold the
jaw against the scroll-gear.
8. Rotate the chuck key clockwise one turn to
engage the tip of the scroll-gear lead thread
into the jaw. Pull the jaw; it should be locked
into the jaw guide.
9. Install the remaining jaws in numerical order,
in the same manner.
—If installed correctly, the jaws will converge
evenly at the center of the chuck.
—If the jaws do not converge evenly, remove
them. Re-install the jaws sequentially 1–3,
and make sure each one engages with the
scroll-gear lead thread during its first rotation.
Model G0602/G0752 (Mfd. Since 03/17)
INCORRECT
Unsafe Jaw Position and
Poor Scroll Gear Engagement
Poor Grip
Unstable
Workpiece
CORRECT
INCORRECT
Unsafe Inside
Jaw Use
Safer Outside
Jaw Use
Poor Scroll
Gear
Engagement
Shallow
Bar Stock
CORRECT
Unsafe Jaw
Position
INCORRECT
Unsafe Jaw Position
Safer Inside
Jaw Use
Cylinder
Poor Scroll
CORRECT Gear Engagement
INCORRECT
Figure 29. Jaw selection and workpiece holding.
-29-
4-Jaw Chuck
Refer to the Chuck Installation (see Page 27)
and Chuck Removal (see Page 28) instructions
to install or remove the 4-jaw chuck.
The 4-jaw chuck features independently adjustable hardened steel jaws for holding non-concentric or off-center workpieces. Each jaw can
be independently removed from the chuck body
and reversed for a wide range of work holding
versatility.
5. Tighten each jaw in small increments. After
you have adjusted the first jaw, continue
tightening the remaining jaws in an opposing
sequence, as shown by the sequential order
in Figure 30.
1
Workpiece
Center Point
4
Because of the dynamic forces involved in
machining a non-concentric or off-center
workpiece, always use a low spindle speed
to reduce risk of the workpiece coming loose
and being thrown from the lathe, which could
cause death or serious personal injury.
Tools Needed:
Qty
4-Jaw Chuck Key............................................... 1
Dial Indicator...................................................... 1
To mount the workpiece:
3
2
Figure 30. 4-jaw tightening sequence.
6. After the workpiece is held in place by the
jaws, use a dial indicator to make sure the
workpiece is centered in the chuck.
—If the workpiece is not correctly centered,
make fine adjustments by slightly loosening one jaw and tightening the opposing
jaw until the workpiece is correctly positioned (see Figure 31 for an example).
1. DISCONNECT LATHE FROM POWER!
2. Place a chuck cradle or plywood on the
bedway below the chuck to protect the
bedway surfaces.
3. Use the chuck key to open each jaw so the
workpiece will lay flat against the chuck face,
jaw steps, or into the spindle opening.
4. With help from another person or a holding
device, position the workpiece so it is centered in the chuck.
-30-
Figure 31. Generic picture of non-cylindrical
workpiece correctly mounted on the 4-jaw chuck.
Model G0602/G0752 (Mfd. Since 03/17)
Faceplate
Refer to the Chuck Installation (see Page 27)
and Chuck Removal (see Page 28) instructions
to install or remove the faceplate.
The faceplate included with your lathe can be
used for a wide range of operations, including
machining non-concentric workpieces, straight
turning between centers, off-center turning, and
boring.
The tools needed for mounting a workpiece will
vary depending on the type of setup you have.
Machining non-concentric workpieces at a
high speed could cause the workpiece to be
thrown from the spindle with deadly force
at the operator or bystanders. To reduce
this risk, only machine non-concentric
workpieces at low speeds and clamp
counter-weights to the faceplate to balance
it.
Failure to properly secure a workpiece to
the faceplate could cause the workpiece to
be thrown from the lathe with deadly force at
the operator or bystanders. Use a minimum
of THREE independent clamping devices to
hold the workpiece onto the faceplate.
Model G0602/G0752 (Mfd. Since 03/17)
To mount a non-concentric workpiece to the
faceplate:
1. DISCONNECT LATHE FROM POWER!
2. Protect the bedway with a piece of plywood.
3. With help from another person or a holding
device to support the workpiece, position it
onto the faceplate and clamp it in place with
a minimum of three independent clamping
devices (see Figure 32 for an example).
Be sure to take into account the rotational
and cutting forces that will be applied to the
workpiece when clamping it to the faceplate.
If necessary, use counter-weights to balance
the assembly and use a dial indicator to make
sure that the workpiece is properly positioned
for your operation.
Non-Cylindrical
Workpiece
Clamp
Faceplate
Figure 32. Generic picture of workpiece clamped
in a faceplate.
-31-
Tailstock
The tailstock (see Figure 33) is typically used to
support long workpieces by means of a live or
dead center (refer to Centers on Page 36). It can
also be used to hold a drill or chuck to bore holes
in the center of a part. Custom arbors and tapers
can also be cut on your lathe by using the offset
tailstock adjustment.
Installing Tooling
This tailstock uses a quill with an MT#3 taper that
accepts a variety of tapered arbors and tooling,
including tang arbors and drill bits (see Figures
34–35 for examples).
Solid
End
Open
End
Solid
End
Screw
End
Tang
Quill Lock
Lever
Tailstock
Lock Nut
Figure 34. Types of tapered arbors and tooling.
Tang
Quill Handwheel
Figure 33. Tailstock and quill lock handles in
locked position.
Graduated Dial
Increments.................................................. 0.001"
One Full Revolution.................................... 0.060"
Increments on Quill
Inch ..............................0"-2 1⁄ 2" in 1⁄ 8" Increments
Metric...................... 0–65mm in 1mm Increments
Positioning Tailstock
1. Loosen the tailstock lock nut to unlock the
tailstock from the bedway.
2. Slide the tailstock to the desired position.
3. Tighten the tailstock lock nut to lock the
tailstock against the bedway.
Using Quill
1. Loosen the quill lock lever.
2. Turn the quill handwheel clockwise to move
the quill toward the spindle or counterclockwise to move it away from it.
Figure 35. Example photos of inserting MT#3
tools with tangs into a typical tailstock.
Note: If the tooling has an open hole in the end,
then a screw can be threaded into the end of the
tool to provide a solid surface for the quill pin to
push against when the quill is retracted for tool
removal. Otherwise, removal of such tooling may
be difficult.
3. Tighten the quill lock lever.
-32-
Model G0602/G0752 (Mfd. Since 03/17)
To install tooling in the tailstock:
To offset the tailstock:
1. With the tailstock locked in place, unlock the
quill, then use the handwheel to extend it
approximately 1".
1. Loosen the tailstock lock nut (see Figure 36).
2. Thoroughly clean and dry the tapered mating
surfaces of the quill and the center, making
sure that no lint or oil remains on the tapers.
3. With a firm and quick motion, insert the tool
into the quill, as shown in Figure 35 on Page
32. Check to see if it is firmly seated by
attempting to twist it—a firmly seated tool will
not twist.
Tailstock
Lock Nut
Adjustment
Set Screw
(1 of 2)
Offset
Indicator
4. Unlock the tailstock and move it until the tip
of the tool is close to, but not touching, the
workpiece, then re-lock the tailstock.
Figure 36. Left offset adjustment.
5. Start spindle rotation, unlock the quill lock
lever, then turn the quill handwheel clockwise
to feed the tool into the workpiece.
2. Rotate the adjustment set screws in opposite
directions for the desired offset (see the illustration in Figure 37).
Removing Tooling
1. Use a shop rag to hold the tool.
2. Rotate the quill handwheel counterclockwise
until the tool is forced out of the quill.
Offsetting Tailstock
The tailstock can be offset from the spindle centerline for turning tapers. Move the tailstock top
casting toward the front of the lathe to machine a
taper at the tailstock end. Conversely, position the
tailstock top casting toward the back of the lathe
to machine a taper at the spindle end.
Note: The marks on the offset indicator are arbitrary. For a precise offset, use a dial indicator to
check quill movement while adjusting the screws.
Turn
CCW
Turn
CW
Turn
CW
Turn
CCW
Figure 37. Set screw adjustment in relation to
tailstock movement.
3. Retighten the tailstock lock nut to secure the
offset.
Qty
Tools Needed
Hex Wrench 4mm............................................... 1
Open-End Wrench 19mm................................... 1
Model G0602/G0752 (Mfd. Since 03/17)
-33-
Aligning Tailstock to Spindle
Centerline
This is an essential adjustment that should be verified or performed each time the tailstock is used
to turn concentric workpieces between centers
or immediately after offsetting the tailstock when
turning a taper. If the tailstock is not aligned with
the spindle centerline when it is supposed to be,
turning results will be inaccurate along the length
of the workpiece.
Note: As long as this dead center remains in
the chuck, the point of the center will remain
true to the spindle centerline. The point will
have to be refinished whenever the center is
removed and then returned to the chuck.
4. Install a center in the tailstock.
5. Attach a lathe dog to the test stock from Step
2, then mount it between the centers (see
Figure 39 for an example).
Items Needed
Qty
Hex Wrench 4mm............................................... 1
Open-End Wrench 19mm................................... 1
Round Stock 2" x 6"........................................... 2
Precision Level................................................... 1
Precision Calipers.............................................. 1
Dial Indicator...................................................... 1
To align the tailstock to the spindle centerline:
1. Use the precision level to make sure the
bedway is level from side-to-side and from
front-to-back.
—If the bedway is not level, correct this condition before continuing (refer to Leveling
& Mounting on Page 21).
Figure 39. Example photo of stock mounted
between the centers.
6. Turn 0.010" off the stock diameter.
2. Center drill both ends of one piece of round
stock, then set it aside for use in Step 5.
7. Mount a test or dial indicator so that the
plunger is on the tailstock quill.
3. Use the other piece of round stock to make
a dead center, and turn it to a 60° point, as
illustrated in Figure 38.
Note: If necessary in the following step,
refer to Offsetting Tailstock on Page 33 for
detailed instructions.
Figure 38. Turning a dead center.
-34-
Model G0602/G0752 (Mfd. Since 03/17)
8. Use calipers to measure both ends of the
workpiece.
—If the test stock is thicker at the tailstock
end, move the tailstock toward the front of
the lathe 1⁄2 the distance of the amount of
taper (see Figure 40).
—If the test stock is thinner at the tailstock
end, move the tailstock toward the back of
the lathe 1⁄2 the distance of the amount of
taper (see Figure 41).
Looking down from above
Move the tailstock toward
the front of the machine half
the distance of the taper
Move tailstock toward the
back of the machine half
the distance of the taper
Looking down from above
Figure 40. Adjust tailstock toward the operator.
Model G0602/G0752 (Mfd. Since 03/17)
Figure 41. Adjust tailstock away from the
operator.
9. Repeat Steps 6–8 until the desired accuracy
is achieved.
-35-
Centers
Live Centers
Figure 42 shows one of the two included MT#3
dead centers and the MT#4 dead center.
A live center (not included) has bearings that
allow the center tip and the workpiece to rotate
together; it can be installed in the tailstock quill for
higher speeds.
Mounting Dead Center in Spindle
MT#4 Dead
Center
MT#3 Dead
Center
Figure 42. Dead centers.
The spindle taper is an MT#4 and will only receive
the MT#4 dead center. The tailstock quill taper
is an MT#3 and will only receive the MT#3 dead
centers.
Dead Centers
A dead center is a one-piece center that does not
rotate with the workpiece and is used to support
long, slender workpieces in the tailstock.
A carbide-tipped dead center (not included) can
better withstand the effects of friction than a typical dead center and is best used in the tailstock
where the workpiece will rotate against it. The tip
of a dead center must be generously lubricated
during the operation to avoid premature wear and
maximize smooth operation. Using low spindle
speeds will also reduce the heat and wear from
friction.
Use the dead center in the spindle for operations
where the workpiece rotates with the center and
does not generate friction.
-36-
1. DISCONNECT LATHE FROM POWER!
2. Thoroughly clean and dry all threads and
mating surfaces of the spindle bore and the
center, making sure that no lint or oil remains
on these surfaces.
Note: This will prevent the tapered surfaces
from seizing due to operational pressures,
which could make it very difficult to remove
the center.
3. Mount a chuck or faceplate onto the spindle,
whichever is correct for your operation.
4. Insert the center into the spindle bore through
the chuck or faceplate.
Figure 43 shows an example photo of a dead
center installed in the spindle, using a lathe
dog and faceplate for turning between centers.
Dead Center
Lathe
Dog
Figure 43. Example photo of using a dead
center with a faceplate and lathe dog.
Model G0602/G0752 (Mfd. Since 03/17)
Removing Center from Spindle
To remove the center from the spindle, insert a
piece of round bar stock or similar tool through the
outboard end (on the left side of the headstock).
Have another person hold onto the center with
a gloved hand or shop rag, then tap the center
loose.
3. Use the quill handwheel to feed the quill out
of the casting approximately 1" (see Figure
1).
Note: The maximum quill travel is 21⁄2", but
we do not recommend extending the quill
more than 2" or stability and accuracy will be
reduced.
Mounting Center in Tailstock
The included dead center or a live center can be
used in the tailstock. Mounting instructions are
the same for both. Figure 44 shows an example
photo of a dead center mounted in a tailstock.
Dead Center
Figure 1. Dead center inserted into tailstock.
4. Insert the center into the tailstock quill.
Figure 44. Example photo of using a dead
center installed in the tailstock.
To avoid premature wear of the dead center
or damage to the workpiece, use low spindle
speeds and keep the tip of the dead center
mounted in the tailstock well lubricated.
To mount a center in the tailstock:
1. DISCONNECT LATHE FROM POWER!
2. Thoroughly clean and dry the tapered mating
surfaces of the tailstock quill bore and the
center, making sure that no lint or oil remains
on the tapers.
Model G0602/G0752 (Mfd. Since 03/17)
5. Seat the center firmly into the quill during
workpiece installation by rotating the quill
handwheel clockwise to apply pressure, with
the center engaged in the center hole in the
workpiece.
Note: Only apply enough pressure with the
tailstock quill to securely mount the workpiece
between centers. Avoid overtightening the
center against the workpiece, or it may
become difficult to remove later, and it will
result in excessive friction and heat, which
may damage the workpiece and center.
6. Secure the quill lock lever and tailstock lock
nut.
Removing Center from Tailstock
To remove the center from the quill, hold onto it
with a gloved hand or shop rag, then rotate the
quill handwheel counterclockwise to draw the quill
back into the casting until the center releases.
-37-
Steady Rest
Mounting Workpiece Between
Centers
1. DISCONNECT LATHE FROM POWER!
2. Drill center holes in both ends of the workpiece.
3. Install a dead center in the spindle with a
lathe dog and a chuck or faceplate, then
install a live center or carbide-tipped dead
center in the tailstock.
The steady rest supports long shafts and can
be mounted anywhere along the length of the
bedway.
Familiarize yourself with the steady rest components shown in Figure 46 to better understand its
operation.
4. Lubricate the workpiece center holes, then
mount the workpiece between the centers
and hold it in place with light pressure from
the tailstock center.
Finger
Lock Nut
5. Seat the center firmly into the quill by rotating
the quill handwheel clockwise to apply pressure against the workpiece (see the example
in Figure 45).
Note: Only apply enough pressure to securely mount the workpiece between centers.
Avoid over-tightening the center against the
workpiece, or it may become difficult to
remove later. Also, over-tightening will result
in excessive friction and heat, which may
damage the workpiece or center.
Finger
Adjustment
Knob
Finger
Lock
Nut
Figure 46. Steady rest components.
To install and use the steady rest:
1. DISCONNECT LATHE FROM POWER!
2. Thoroughly clean all mating surfaces, then
place the steady rest base on the bedways
so the triangular notch fits over the bedway
prism.
3. Loosen the finger lock nuts shown in
Figure 46, turn the finger adjustment knobs,
and adjust the fingers as required for the
workpiece.
Figure 45. Example photo of a workpiece
mounted between the centers.
6. Secure the quill lock lever and tailstock lock
nut.
4. Loosen the steady rest lock nut, position the
steady rest where required to properly support the workpiece, then secure the lock nut.
5. Turn the finger adjustment knobs so the fingers are barely touching the workpiece, then
tighten the finger lock nuts.
6. Lubricate the finger tips with an anti-seize
lubricant during operation.
-38-
Note: Mill or file the tips if they show wear.
Model G0602/G0752 (Mfd. Since 03/17)
Follow Rest
Compound Rest
The follow rest mounts to the saddle with two cap
screws (see Figure 47). It is used on long, slender
parts to prevent workpiece deflection from cutting
tool pressure during operation. Adjust the follow
rest fingers in the same manner as the those on
the steady rest.
The compound rest handwheel has an indirectread graduated scale. This means the distance
shown on the scale represents the actual distance
the tool moves. The base of the compound rest
has another graduated scale used for setting the
cutting tool to a specific angle.
Note: To reduce the effects of friction, lubricate
the finger tips with generous anti-sieze lubricant
during operation.
Graduated Dial
Increments................................ 0.001" (0.025mm)
One Full Revolution...................... 0.04" (1.02mm)
Tool Needed
Qty
Open-End Wrench 14mm................................... 1
Cap
Screws
To set the compound rest at a certain angle:
1. Loosen the two hex nuts at the base of the
compound rest (1 of 2 shown in Figure 49).
Figure 47. Follow rest attachment.
Hex Nut
(1 of 2)
Compound
Rest
Angle Scale
Carriage & Slide
Locks
The carriage and cross slide have locks that can
be tightened to provide additional rigidity during
operation, especially during heavy cuts.
See Figure 48 to identify the locations of the
locks for each device.
Carriage
Lock
Cross Slide
Lock
Figure 49. Compound rest.
2. Rotate the rest to the desired angle, as
indicated by the scale at the base,
then retighten the two hex nuts.
Tip: The first time you set the angle of the
compound rest for cutting threads, mark the
location on the cross slide as a quick reference point. This will allow you to quickly
return the compound rest to that exact angle
the next time you need to cut threads.
Figure 48. Carriage and cross slide locks.
Model G0602/G0752 (Mfd. Since 03/17)
-39-
Four-Way Tool Post
The four-way tool post is mounted on top of the
compound rest and allows a maximum of four 1⁄2"
tools to be loaded simultaneously.
Aligning Cutting Tool with Spindle
Centerline
For most operations, the cutting tool tip should be
aligned with the spindle centerline, as illustrated
in Figure 51.
Each tool can be quickly indexed to the workpiece
by loosening the top handle, rotating the tool post
to the desired position, then re-tightening the
handle to lock the tool into position.
Cutting
Tool
Spindle
Center
Line
Installing Tool
Tool Needed
Qty
Hex Wrench 6mm............................................... 1
To install a tool in the tool post:
1. Adjust the tool post screws so that the cutting
tool can fit underneath them (see Figure 50).
Cutting
Tool
Tool Post
Screw
Figure 51. Cutting tool aligned with spindle
centerline (viewed from tailstock).
There are a number of ways to check and align
the cutting tool to the spindle centerline. If necessary, you can raise the cutting tool by placing
steel shims underneath it. The shims should be
as long and as wide as the cutting tool to properly
support it.
Below are two common methods:
Figure 50. Example of tool mounted in tool post.
Over-extending a cutting tool from the post
will increase the risk of tool chatter, breakage,
or tool loosening during operation, which
could cause metal pieces to be thrown at
the operator or bystanders with great force.
DO NOT extend a cutting tool more than 2.5
times the width of its cross-section (e.g.,
2.5 x 0.5" = 1.25").
•
Move the tailstock center over the cross slide
and use a dial indicator to measure the distance from the surface of the cross slide to
the tip of the center. Adjust the cutting tool
height so it is the same distance above the
cross slide as the tailstock center.
•
Align the tip of the cutting tool with a tailstock
center, as instructed in the following procedure. For this to work, the tailstock must
be aligned to the spindle centerline (refer to
Aligning Tailstock To Spindle Centerline
on Page 34 for detailed instructions).
2. Firmly secure the cutting tool with at least two
tool post screws.
3. Check and adjust the cutting tool to the
spindle centerline, as instructed in the next
subsection.
-40-
Model G0602/G0752 (Mfd. Since 03/17)
Tools Needed
Qty
Hex Wrench 6mm............................................... 1
Steel Shims........................................ As Needed
Cutting Tool........................................................ 1
Tailstock Center.................................................. 1
Manual Feed
The handwheels shown in Figure 53 allow the
operator to manually move the cutting tool.
To align the cutting tool with the tailstock
center:
1. Mount the cutting tool in the tool post, then
secure the post so the tool faces the tailstock.
2. Install a center in the tailstock, and position
the center tip near the cutting tool tip.
Compound Rest
Handwheel
Carriage
Handwheel
3. Lock the tailstock and quill in place.
4. Adjust the height of the cutting tool so that the
tool tip is aligned vertically and horizontally
with the center tip, as shown in Figure 52.
Cross Slide
Handwheel
Figure 53. Manual handwheel controls.
Carriage Handwheel
Use the carriage handwheel to move the carriage
left or right along the bed. This control is helpful when setting up the machine for turning or
when manual movement is desired during turning
operations.
(Top View)
Tailstock
Center
Cutting
Tool
Cutting
Tool
Tailstock
Center
(Side View)
Figure 52. Cutting tool aligned to the tailstock
center.
Cross Slide Handwheel
Graduated Dial
Increments................................ 0.001" (0.025mm)
One Full Revolution...................... 0.06" (1.52mm)
Use this handwheel to move the tool toward and
away from the work. Adjust the position of the
graduated scale by holding the handwheel with
one hand and turning the dial with the other.
The cross slide handwheel has an indirect-read
graduated dial. This means the distance shown
on the scale represents the actual distance the
tool moves.
Compound Rest Handwheel
Graduated Dial
Increments . ............................. 0.001" (0.025mm)
One Full Revolution...................... 0.04" (1.02mm)
Use this handwheel to move the cutting tool linearly along the set angle of the compound rest.
Set the compound rest angle by hand-rotating it
and securing in place with two hex nuts. The compound rest has an indirect-read graduated dial.
Model G0602/G0752 (Mfd. Since 03/17)
-41-
Spindle Speed
Using the correct spindle speed is important for
safe and satisfactory results, as well as maximizing tool life.
To set the spindle speed for your operation, you
will need to: 1) Determine the best spindle speed
for the cutting task, and 2) configure the lathe
controls to produce the required spindle speed.
Setting Spindle Speed
Selecting one of the available six spindle speeds
(Model G0602) or one of the three spindle speed
ranges (Model G0752) is performed by repositioning the V-belt(s) between the pulleys.
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
Hex Wrench 8mm............................................... 1
Open-End Wrench 17mm................................... 1
Determining Spindle Speed
Use a low RPM when machining
heavy eccentric workpieces;
securely clamp your workpiece
and remove the chuck key!
Objects thrown from a lathe can
cause serious injury or death to
the operator or bystanders.
Many variables affect the optimum spindle speed
to use for any given operation, but the two most
important are the recommended cutting speed
for the workpiece material and the diameter of
the workpiece, as noted in the formula shown in
Figure 54.
*Recommended
Cutting Speed (FPM) x 12
Spindle
= Speed
Dia. of Cut (in inches) x 3.14
(RPM)
*Double if using carbide cutting tool
Figure 54. Spindle speed formula for lathes.
Cutting speed, typically defined in feet per minute
(FPM), is the speed at which the edge of a tool
moves across the material surface.
Use a minimum of three independent clamping
devices when turning eccentric workpieces
on the faceplate. Failure to provide adequate
clamping will cause workpiece to eject.
G0602 Configuration Examples
The 271⁄ 2" belt is used on pulleys B and C (see
Figure 55) with the tensioner for 50, 300, and
560 RPM.
A recommended cutting speed is an ideal speed
for cutting a type of material in order to produce
the desired finish and optimize tool life.
The books Machinery’s Handbook or Machine
Shop Practice, and some internet sites, provide excellent recommendations for which cutting
speeds to use when calculating the spindle speed.
These sources also provide a wealth of additional
information about the variables that affect cutting
speed and they are a good educational resource.
Also, there are a large number of easy-to-use
spindle speed calculators that can be found on
the internet. These sources will help you take into
account the applicable variables in order to determine the best spindle speed for the operation.
-42-
C
B
Tensioner
Used
A
Figure 55. Positioning belt for low speed.
Model G0602/G0752 (Mfd. Since 03/17)
The 33" belt is used on pulleys A and C (see
Figure 56) without the tensioner for 720, 1200,
and 2400 RPM.
C
B
Tensioner
Not Used
3. Open the change gear cover, then loosen the
tensioner lock nut located on the other side of
the gear cover plate and the headstock.
Locking Nut
A
Figure 56. Positioning belt for high speed.
Follow along with the examples below for setting
the Model G0602 spindle speed to gain a better
understanding of this task.
To set the spindle speed to 150 RPM:
1. DISCONNECT LATHE FROM POWER!
2. Refer to the RPM chart in Figure 57 to determine the pulley combination you need to
achieve a spindle speed of 150 RPM—it is
BC1.
RPM Chart
Figure 58. Location of tensioner lock nut.
4. Move the tensioner to install the 271⁄ 2" belt
between pulleys B and C, and in sheave 1,
as shown in Figure 55 on Page 42.
5. Re-tension the belt (refer to "Tensioning
V-Belt" on Page 63), then close the change
gear cover and secure it. The lathe is now set
for a spindle speed of 150 RPM.
G0752 Configuration Example
The V-belt is positioned on the spindle and motor
pulleys with the tensioner (see Figure 59) to select
between low (100-800 RPM), medium (160-1300
RPM), and high (250–2000 RPM) speed ranges.
Bolt
RPM
Pulley
Combination
Tensioner
Spindle
Pulley
Figure 57. G0602 RPM chart.
Motor
Pulley
L M H
Figure 59. Positioning belt for low speed.
Model G0602/G0752 (Mfd. Since 03/17)
-43-
Follow along with this example for setting the
spindle speed for the Model G0752 to gain a better understanding of this task.
To set the spindle speed to 150 RPM:
1. DISCONNECT LATHE FROM POWER!
2. Open the change gear cover, use an 8mm
hex wrench to loosen the tensioner bolt, then
move the tensioner out of the way.
3. Move the V-belt to the outer pulley sheaves
to select the low speed range (100-800
RPM), as shown in Figure 59.
4. Re-tension the belt (refer to "Tensioning
V-Belt" on Page 63) and secure the tensioner.
5. Turn the spindle direction switch to FWD, and
press the ON button.
6. Adjust the spindle speed dial until the spindle
speed display reads 150 RPM.
Power Feed
The carriage has power feed capability when it
is engaged with the lead screw. The rate that the
carriage moves (feed rate) is controlled by V-belt,
change gear, and gearbox dial configurations.
Feed rate and spindle speed must be considered
together when determining the proper cutting
speed for a given workpiece. The sources you
use to determine the optimum spindle speed for
an operation will also provide the optimal feed rate
to use with that spindle speed.
Often, the experienced machinist will use the
feeds and speeds given in their reference charts
or web calculators as a starting point, then make
minor adjustments to the feed rate (and sometimes spindle speed) to achieve the best results.
The carriage can alternately be driven by the
leadscrew for threading operations. However, this
section only covers using the power feed option
for the carriage for non-threading operations. To
learn how to power the carriage for threading
operations, refer to Threading on Page 46.
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
Hex Wrench 6mm............................................... 1
-44-
Model G0602/G0752 (Mfd. Since 03/17)
Setting Power Feed Rate
The feed rate chart on the headstock displays the
settings for the feed controls for inch feed rates.
Using the controls on the lathe, follow along with
the example below to better understand how to
set the lathe for the desired power feed rate.
Setting Power Feed Rate of 0.0120 in/rev
1. DISCONNECT LATHE FROM POWER!
Note: All change gears are stamped with the
number of teeth they have.
7. Move the lash adjuster so the gear backlash
is between 0.003" to 0.008", tighten the lash
adjuster cap screw, then close and secure
the change gear cover.
8. Loosen the carriage lock (see Figure 60),
and push down on the half nut lever to
engage the power feed.
2. Turn the feed dials to the numeral and letter
indicated by the chart in Figure 61.
Note: You may have to rock the chuck by
hand to get the gearbox gears to mesh.
3. Gather the required change gears, based
upon the chart in Figure 61.
4. Remove the cap screw that secures the
change gear cover, open the cover, then
loosen the lash adjuster cap screw (see
Figure 61) and swing the change gear
assembly out of the way.
5. Remove the E-clips and cap screw from the
change gears.
6. Lubricate the change gears (refer to Page 55
for detailed instructions) and swap them out
in the order shown on the chart in Figure 61,
then re-install the E-clips and cap screw.
40
27
Carriage Lock
Cap Screw
Half Nut
Lever
Figure 60. Carriage lock and feed control.
The lathe is now set up for a power feed rate of
0.0120 in/rev.
To avoid potential carriage/chuck crash,
disengage the half-nut lever immediately
after completing power feeding operations.
60
Feed Chart
Change Gears
E-Clips
Cap
Screw
56
127
104
= 0.012" Feed
Lash Adjuster Cap Screw
Feed Dials
Figure 61. Power feed setup.
Model G0602/G0752 (Mfd. Since 03/17)
-45-
Threading
4. Open the change gear cover, loosen the lash
adjuster (Figure 61 on Page 45) and swing
the change gear assembly out of the way.
The following subsections describe how to use
the threading controls and charts to set up the
lathe for a threading operation. If you are unfamiliar with the process of cutting threads on a lathe,
we strongly recommend that you read books,
review industry trade magazines, or get formal
training before attempting any threading projects.
5. Remove the E-clips and cap screw from the
change gears.
Headstock Threading Controls
The threading charts on the headstock face display the settings for metric and inch threading.
Using the controls on the lathe, complete the following examples to better understand how to set
up the lathe for the desired threading operation.
6. Lubricate the change gears (refer to Page 55
for detailed instructions) and swap them out
in the order shown on the chart in Figure 62,
then secure the change gears with the E-clips
and cap screw.
Note: All change gears are stamped with the
number of teeth they have.
7. Move the lash adjuster so the gear backlash
is between 0.003" to 0.008", tighten the lash
adjuster cap screw, and close the cover.
To set the lathe to cut 64 TPI threads:
8. Loosen the carriage lock (see Figure 60 on
Page 45).
1. DISCONNECT LATHE FROM POWER!
The lathe is now set up to cut 64 TPI threads.
2. Turn the feed dials to the numeral and letter
indicated by the chart in Figure 62.
Note: You may have to rock the chuck by
hand to mesh the gearbox gears.
When threading keep your hand on the halfnut lever ready to disengage the half nut to
avoid potential carriage/chuck crash.
3. Gather the required change gears based
upon the chart.
Inch
Thread
Chart
E-Clips
Cap
Screw
= 64 TPI
Lash Adjuster
Figure 62. Threading setup for 64 TPI.
-46-
Model G0602/G0752 (Mfd. Since 03/17)
To set the lathe to cut 0.45 TPmm threads:
The steps for setting up the lathe for threading metric threads are the same as those for inch threads. Follow
the instructions on Page 46 for setting the thread pitch to 64 TPI, and refer to the chart below.
Metric Thread Chart
= 0.45 TPmm
Figure 63. Metric threading setup.
Apron Threading Controls
Thread Dial Chart
The half nut lever engages the carriage with the
leadscrew, which moves the carriage and cutting
tool along the length of the workpiece for threading and power feed operations (see Figure 64).
Find the TPI (threads per inch) that you want
to cut in the left column of the thread dial chart
(see Figure 65), then reference the dial number
to the right of it. The dial numbers indicate when
to engage the half nut for a specific thread pitch.
The thread dial chart can also be found on the
carriage beside the half nut lever.
The numbers on the thread dial are used with the
thread dial chart to show when to engage the half
nut during inch threading. The thread dial numbers are not used when cutting metric threads,
since this lathe has an inch leadscrew.
Half Nut
Lever
Thread Dial
Figure 64. Half nut lever and thread dial.
Indicator Table
TPI
SCALE
9
1-12
1-12
12
1-12
18
24
1-12
1-12
36
48
1-12
1-12
72
9½,11½, ,13½
1.7
Other TPI 1.4.7.10
Figure 65. Thread dial chart.
When threading, we recommend using the
slowest speed possible and avoiding deep
cuts, so you are able to disengage the half
nut when required and prevent an apron
crash!
Model G0602/G0752 (Mfd. Since 03/17)
Note: Since this lathe has an inch leadscrew,
do not use the thread dial when cutting metric
threads. Instead you must leave the half nut
engaged from the beginning until the threading
operation is complete.
-47-
TPI
11 9
1
1
5
5
3
7
ANY
9, 12, 18, 24, 36, 48, 72 POSITION
9
All Other TPI
11
TPI
3
1
POSITION
1,4, 7, 10
5
All Other TPI
For all other TPI's, use numbered lines 1 or 7 or
non-numbered lines 4 or 10 on the thread dial
(see Figure 68).
3
9, 12, 18, 24, 36, 48, 72 TPI
For these threading TPI's, use any of the lines on
the thread dial (see Figure 66).
7
The following examples explain how to use the
thread dial chart.
POSITION
1,7
7
91/2 ,111/2 ,131/2
11 9
TPI
TPI
Figure 68. All other TPIs.
11 9
1
ANY
9, 12, 18, 24, 36, 48, 72 POSITION
Figure 66. 9, 12, 18, 24, 36, 48, 72 TPIs.
5
3
7
91⁄2, 111⁄2 ,131⁄2 Fractional TPI
For threading these TPIs, use the numbered lines
TPI
1 or 7 on the thread dial (see Figure 67).
POSITION
91/2 ,111/2 ,131/2
1,7
1
11 9
1
TPI
Figure
67. 91⁄2, 111⁄2 131⁄2 TPIs.
POSITION
All Other TPI
1,4, 7, 10
3
5
11
POSITION
1,7
7
91/2 ,111/2 ,131/2
11 9
TPI
3
7
5
1
9
TPI
11
1
9
-48-
5
3
POSITION
1,4, 7, 10
7
All Other TPI
3
7
5
Model G0602/G0752 (Mfd. Since 03/17)
SECTION 5: ACCESSORIES
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
H6204—High Precision Drill Chuck 5/8" x JT3
Unlike most keyed drill chucks, this one is made
to very tight tolerances on CNC equipment and is
one of the finest drill chucks on the market today.
It has very high gripping strength and is suitable
for heavy-duty, high-speed drilling. Each chuck
includes a high visibility chuck key. Specifications:
1
⁄ 32"- 5 ⁄ 8" x JT #3.
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
SBCE3450—How to Run a Lathe
First printed in 1907 by South Bend Lathe, this
56th edition is an exact reprint from 1966. Well
illustrated with vintage photos and drawings, this
128-page book is written specifically about the
care and operation of a metal lathe. “This book is
to aid the beginner or apprentice in the machine
shop and the student in the school shop to secure
a better understanding of the fundamental operations of modern lathe practice in use in modern
industries in the United States.”
Figure 70. H6204 Drill Chuck.
G1677—Drill Chuck Arbor - MT3/JT3
This Drill Chuck Arbor is used to adapt drill chucks
to your drill press, milling machine or lathe. Long
end: MT #3, Short end: J.T. #3.
Figure 71. G1677 Drill Chuck Arbor.
Figure 69. SBCE3450 South Bend Lathe~How
to Run a Lathe book.
G9849—Magnetic Base/Dial Indicator Combo
Precision measurements and set-ups have never
been so easy. Magnetic base engages with just
the turn of a switch and allows pinpoint adjustment. The dial indicator features 0–1" travel and
has a resolution of 0.001". Set includes a molded
case for protection and convenience.
H2987—½" Bent Lathe Dog
H2988—1" Bent Lathe Dog
H2989—1½" Bent Lathe Dog
H2990—2" Bent Lathe Dog
H2991—3" Bent Lathe Dog
Figure 72. G9849 Magnetic Base/Dial Indicator.
Model G0602/G0752 (Mfd. Since 03/17)
-49-
G5640—5-Pc. 1 ⁄ 2" Indexable Carbide Tool Set
G6706—Replacement TiN Carbide Inserts
Five-piece turning tool set features indexable carbide inserts with "spline" type hold-down screw
that allow indexing without removing the screw.
Each set includes AR, AL, BR, BL, and E style
tools with carbide inserts, hex wrench, extra holddown screws and a wooden case.
H7616—Oil Can w/Plastic Nozzle
H7617—Oil Can w/Flexible Plastic Nozzle
These high-pressure oil cans are perfect for lubricating the ball oilers found on your machine. Each
can holds 5 ounces of oil.
H7616
H7617
Figure 73. G5639 5 Pc. Indexable Tool Set.
T10255—Mini Lathe Tooling Kit
This convenient Mini Lathe Tool Kit includes right,
left and straight turning tool holders with 1⁄ 8" HSS
tool bits, boring bar with holder and 1⁄ 8" HSS tool
bit, cut off tool holder with 3 ⁄ 32" HSS blade and
3
⁄ 8" shank, mini cut off tool holder with 1⁄ 16" HSS
blade and 5 ⁄ 16" shank, knurling tool holder with
pivoting head, single horizontal/vertical knurling
tool holder and assorted hex wrenches. Maximum
shank size is 1⁄ 2".
Figure 75. High-pressure oil cans for ball oilers.
T23962—ISO 68 Moly-D Machine Oil, 5 gal.
T23963—ISO 32 Moly-D Machine Oil, 5 gal.
Moly-D oils are some of the best we've found for
maintaining the critical components of machinery
because they tend to resist run-off and maintain
their lubricity under a variety of conditions—as
well as reduce chatter or slip. Buy in bulk and
save with 5-gallon quantities.
T23962
Figure 74. T10255 Mini Lathe Tooling Kit.
T23963
Figure 76. ISO 68 and ISO 32 machine oil.
H5930—4-Pc Center Drill Set 60°
H5931—4-Pc Center Drill Set 82°
Double ended HSS Center Drills are precision
ground. Includes sizes 1-4.
order online at www.grizzly.com or call 1-800-523-4777
-50-
Model G0602/G0752 (Mfd. Since 03/17)
SECTION 6: MAINTENANCE
Daily, After Operations
Always disconnect power
to the machine before
performing maintenance.
Failure to do this may
result in serious personal injury.
•
•
•
•
Schedule
Ongoing
To help reduce the risk of injury and ensure proper
machine operation, if you ever observe any of the
items below, shut down the machine immediately
and fix the problem before continuing operations:
•
•
•
•
•
Loose mounting bolts or fasteners.
Worn, frayed, cracked, or damaged wires.
Guards or covers removed.
Emergency STOP button not working correctly or not requiring you to reset it before
starting the machine again.
Damaged or malfunctioning components.
Daily, Before Operations
•
•
•
•
•
•
•
Check/add gearbox oil (Page 52).
Add oil to the ball oilers (Page 53).
Clean/lubricate the leadscrew and carriage
rack (Page 54).
Lubricate the bedways (Page 54).
Compound slide (Page 54).
Disengage the half nut on the carriage (to
prevent crashes upon startup).
Ensure carriage lock bolt is loose.
Model G0602/G0752 (Mfd. Since 03/17)
Turn the spindle direction switch to STOP,
and press the Emergency STOP button (to
prevent accidental startup).
Vacuum/clean all chips and swarf from bed
and slides.
Wipe down all unpainted or machined surfaces with an oiled rag.
Add oil to the ball oilers (Page 53).
Annually
•
•
•
Change the gearbox oil (Page 52).
Lubricate the change gears (Page 55).
Check/level bedway (Page 21).
Cleaning/Protecting
Because of its importance, we recommend that
the cleaning routine be planned into the workflow
schedule.
Typically, the easiest way to clean swarf from the
machine is to use a wet/dry shop vacuum that is
dedicated for this purpose. The small chips left
over after vacuuming can be wiped up with a
slightly oiled rag. Avoid using compressed air to
blow off chips, as this may drive them deeper into
the moving surfaces or cause sharp chips to fly
into your face or hands.
All unpainted and machined surfaces should be
wiped down daily to keep them rust free and in top
condition. This includes any surface that is vulnerable to rust if left unprotected (especially parts
that are exposed to water soluble cutting fluid).
Use a quality rust protectorate such as SLIPIT® or
Boeshield ® to prevent corrosion.
-51-
Lubrication
Quick-Change Gearbox
The lathe has numerous metal-to-metal sliding
surfaces that require regular lubrication to maintain smooth movement and ensure long-lasting
operation.
Other than the lubrication points covered in this
section, all other bearings are internally lubricated
and sealed at the factory. Simply leave them
alone unless they need to be replaced.
Before performing any lubrication
DISCONNECT LATHE FROM POWER!
task,
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Reservoir Capacity...................................... 1 Pint
Check/Add Frequency.................................. Daily
Change Frequency................................. Annually
Checking Oil Level
The gearbox reservoir has the proper amount of
oil when the oil level in the sight glass is approximately 3⁄4 full. The oil sight glass is located below
the gearbox control dials, as shown in Figure 77.
Gearbox Fill Plug
Important: Before adding lubricant to ball oilers
and grease fittings, clean off entry points to prevent contamination of lubricant.
Use the schedule and information in the chart
below as a daily guide for lubrication tasks.
We recommend using Grizzly Model T23962 or
T23963 lubricants (see Accessories, Page 50) for
most of the lubrication tasks.
Quick-Change Gearbox
Daily
Ball Oilers
Daily
Page
Ref.
This
page
53
Leadscrew & Carriage
Rack
Daily
54
Bedways
Daily
54
Compound Slide
Daily
54
Annually
55
Lubrication Task
Change Gears
Frequency
NOTICE
The recommended lubrication is based on
light-to-medium usage. Keeping in mind
that lubrication helps to protect the value
and operation of the lathe, these lubrication
tasks may need to be performed more frequently than recommended here, depending on usage.
Failure to follow reasonable lubrication
practices as instructed in this manual could
lead to premature failure of lathe components and will void the warranty.
-52-
Gearbox
Oil Level
Sight Glass
Figure 77. Headstock oil level sight glass.
After break-in, change the oil in the gearbox, then
again after three months. Afterwards, change
the oil on an annual basis or more frequently if
extreme machine use requires it.
Adding Oil
Use an 8mm hex wrench to remove the gearbox
fill plug (see Figure 77), then add the oil until the
level is approximately 3⁄4 full in the oil sight glass.
Drain
Plug
Figure 78. Location of the quick-change gearbox
drain plug.
Draining Oil
Remove the fill plug (Figure 77), place a catch
pan under the quick-change gearbox drain plug
(see Figure 78). Use an 8mm hex wrench to
loosen the drain plug, remove it, then allow the
reservoir to empty. Re-install the drain plug.
Model G0602/G0752 (Mfd. Since 03/17)
Ball Oilers
Oil Type..... Grizzly T23963 or ISO 32 Equivalent
Oil Amount................................. 1 or 2 Squirts/Fill
Lubrication Frequency.................................. Daily
This lathe has 10 ball oilers that should be oiled
on a daily basis before beginning operation.
Proper lubrication of ball oilers is done with a
pump-type oil can that has a plastic or rubberized cone tip. We do not recommend using metal
needle or lance tips, as they can push the ball too
far into the oiler, break the spring seat, and lodge
the ball in the oil galley.
Lubricate the ball oilers before and after machine
use, and more frequently under heavy use. When
lubricating ball oilers, first clean the outside surface to remove any dust or grime. Push the tip of
the oil can nozzle against the ball oiler to create
a hydraulic seal, then pump the oil can once or
twice. If you see sludge and contaminants coming
out of the lubrication area, keep pumping the oil
can until the oil runs clear. When finished, wipe
away any excess oil.
Refer to Figures 79–83 to identify the location of
each ball oiler.
Ball
Oilers
Figure 80. Change gear ball oilers.
Ball Oiler
Ball
Oilers
Ball Oiler
Figure 81. Carriage and cross slide ball oilers.
Ball Oiler
Ball Oilers
Figure 82. Tailstock ball oiler.
Ball Oiler
Figure 79. Spindle bearing ball oilers.
Model G0602/G0752 (Mfd. Since 03/17)
Figure 83. Leadscrew end bearing ball oilers.
-53-
Leadscrew & Carriage Rack
Compound Slide
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Oil Amount.......................................... As Needed
Lubrication Frequency.................................. Daily
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Oil Amount.............................................Thin Coat
Lubrication Frequency.................................. Daily
Before lubricating the leadscrew and carriage
rack (see Figure 84), clean them first with mineral spirits. Use a stiff brush to help remove any
debris or grime. Apply a thin coat of oil along
the length of the carriage rack. Use a stiff brush
to make sure oil is applied into the leadscrew
threads.
Use the handwheel to move the compound slide
all the way toward you (see Figure 85), then wipe
clean the bottom slide with a rag and mild solvent.
Apply the lubricant and move the compound slide
back and forth to distribute the oil.
Bottom Slide
Note: In some environments, abrasive material
can become caught in the leadscrew lubricant and
drawn into the half nut. In this case, lubricate the
leadscrew with a quality dry lubricant.
Bedways
Rack
Leadscrew
Figure 85. Compound bottom slide.
Figure 84. Leadscrew, rack and bedways.
Bedways
Oil Type..... Grizzly T23962 or ISO 68 Equivalent
Oil Amount.......................................... As Needed
Lubrication Frequency.................................. Daily
Before lubricating the bedways (see Figure 84),
clean it with mineral spirits. Apply a thin coat
of oil along the length of the bedway. Move the
steady rest, carriage, and tailstock to access the
entire length of the bedways.
-54-
Model G0602/G0752 (Mfd. Since 03/17)
Change Gears
Grease Type.............................................NLGI#2
Oil Amount.............................................Thin Coat
Frequency................ Annually or When Changing
The change gears, shown in Figure 86, should
always have a thin coat of heavy grease to
minimize corrosion, noise, and wear. Wipe away
excess grease that could be thrown onto the
V-belts and reduce optimal power transmission
from the motor.
To lubricate the change gears:
1. DISCONNECT LATHE FROM POWER!
2. Open the change gear cover and remove all
the change gears shown in Figure 86.
3. Clean the change gears thoroughly with mineral spirits to remove the old grease. Use a
small brush if necessary to clean between the
teeth.
4. Clean the shafts, and wipe away any grease
splatters in the vicinity and on the inside of
the change gear cover.
5. Using a clean brush, apply a thin layer of
grease on the gears. Make sure to get grease
between the gear teeth, but do not fill the
teeth valleys.
Figure 86. Change gears.
To handle and care for the change gears:
Make sure to clean and lubricate any gears you
install or change. Be very careful during handling
and storage—the grease coating on the gears will
easily pickup dirt or debris, which can then spread
to the other gears and increase the rate of wear.
6. Install the change gears and mesh them
together with 0.003"–0.008" backlash. Once
the gears are meshed together, apply a small
dab of grease between them where they
mesh together—this grease will be distributed when the gears rotate and re-coat any
areas scraped off during installation.
7. Close the change gear cover before re-connecting the lathe to power.
Make sure the change gear cover remains installed
whenever possible to keep the gears free of dust
or debris from the outside environment.
Model G0602/G0752 (Mfd. Since 03/17)
-55-
Machine Storage
To prevent the development of rust and corrosion,
the lathe must be properly prepared if it will be
stored for a long period of time. Doing this will
ensure the lathe remains in good condition for
later use.
To prepare the lathe for storage:
1. Run the lathe and bring the gearbox reservoir
to operating temperature, then drain and refill
with clean oil.
2. DISCONNECT LATHE FROM POWER!
3. Thoroughly clean all unpainted, bare metal
surfaces, then apply a liberal coat of way oil,
heavy grease, or rust preventative. Take care
to ensure these surfaces are completely covered but that the rust preventative or grease
is kept off of painted surfaces.
5. Loosen or remove all belts so they do not
become stretched during the storage period.
(Be sure to place a maintenance note near
the power button as a reminder that the belts
have been loosened or removed.)
6. Cover the lathe and place it in a dry area that
is out of direct sunlight and away from hazardous fumes, paint, solvents, or gas. Fumes
and sunlight can bleach or discolor paint.
7. Every few months do the following:
• Rotate by hand all gear-driven components
a few times in several gear selections. This
will keep the bearings, bushings, gears,
and shafts well lubricated and protected
from corrosion—especially during the winter months.
• Slide the carriage, tailstock, and steady
rest down the lathe bed to make sure that
way spotting is not beginning to occur.
4. Lubricate the machine as outlined in the
Lubrication section beginning on Page 52.
Be sure to use an oil can to purge all ball oilers and oil passages with fresh oil.
-56-
Model G0602/G0752 (Mfd. Since 03/17)
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If
you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please
gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Motor & Electrical
Symptom
Possible Cause
Possible Solution
Machine does not
start or a circuit
breaker trips.
1. Emergency stop button engaged or at fault.
6. Contactor not getting energized/has poor
contacts.
7. Motor connection wired wrong.
8. Motor spindle direction switch at fault.
9. Inverter/control box at fault (G0752 only).
10.Motor at fault.
1. Rotate button clockwise until it pops out to reset it
for operation; replace if not working properly.
2. Turn spindle direciton switch to FWD or REV.
Ensure switch has correct voltage. Replace if faulty.
3. Test/replace if faulty.
4. Verify circuit is rated for machine amp load;
troubleshoot and repair cause of overload; replace
weak breaker; find/repair electrical short.
5. Check for broken wires or disconnected/corroded
connections, and repair/replace as necessary.
6. Test for power on all legs and contactor operation.
Replace unit if faulty.
7. Correct motor wiring connections (Page 67).
8. Replace switch.
9. Inspect inverter/controller box; replace if faulty.
10.Test/repair/replace.
Loud, repetitious
noise coming from
lathe at or near the
motor.
1. Pulley set screws or keys are missing or
loose.
2. Motor fan is hitting the cover.
1. Inspect keys and set screws. Replace or tighten if
necessary.
2. Tighten fan, shim cover, or replace items.
Motor overheats.
1. Motor overloaded.
1. Allow motor to cool; reduce load on motor.
Motor is loud when
cutting, or bogs
down under load.
1. Excessive depth of cut or feed rate.
2. Spindle speed or feed rate wrong for
cutting operation.
1. Decrease depth of cut or feed rate.
2. Refer to the feeds and speed charts in Machinery's
Handbook or a speeds and feeds calculator on the
internet.
3. Sharpen or replace the cutting tool.
2. Spindle direction switch turned OFF or at
fault.
3. Start capacitor at fault.
4. Wall fuse/circuit breaker is blown/tripped;
short in electrical system; start-up load too
high for circuit.
5. Wiring is open/has high resistance.
3. Cutting tool is dull.
Model G0602/G0752 (Mfd. Since 03/17)
-57-
Operation
Symptom
Possible Cause
Possible Solution
Entire machine
vibrates upon
startup and while
running.
1. Workpiece is unbalanced.
1. Re-install workpiece as centered with the spindle
bore as possible.
2. Stop lathe immediately and correct interference
problem.
3. Re-tension/replace the V-belt(s) as necessary (see
Page 64).
4. Align the V-belt pulleys.
5. Check installation; re-balance chuck or faceplate;
contact a local machine shop for help.
6. Adjust change gears and establish backlash.
7. Inspect gears, and replace if necessary.
8. Replace broken gear or bearing.
9. Reset spindle bearing preload or replace worn
spindle bearings.
2. Workpiece is hitting stationary object.
3. Loose or damaged V-belt(s).
4. V-belt pulleys are not properly aligned.
5. Chuck or faceplate is unbalanced or not
installed properly.
6. Change gears not aligned or no backlash.
7. Worn or broken gear present.
8. Broken gear or bad bearing.
9. Spindle bearings at fault.
Bad surface finish.
1. Wrong spindle speed or feed rate.
2. Dull tooling or poor tool selection.
3. Tool height not at spindle centerline.
4. Too much play in gibs.
Tapered tool difficult 1. Quill is not retracted all the way back into
the tailstock.
to remove from
2. Contaminants not removed from taper
tailstock quill.
before inserting into quill.
1. Adjust for appropriate spindle speed and feed rate.
2. Sharpen tooling or select a better tool for the
intended operation.
3. Adjust tool height to spindle centerline (see Page
40).
4. Tighten gibs (see Page 61).
1. Turn the quill handwheel until it forces the tapered
tool out of quill.
2. Clean the taper and bore, then re-install tool.
Cross slide,
compound rest, or
carriage feed has
sloppy operation.
1. Gibs are out of adjustment.
2. Handwheel is loose or backlash is high.
1. Adjust gibs (see Page 61).
2. Tighten handwheel fasteners, adjust handwheel
backlash to a minimum (see Page 60).
Cross slide,
compound, or
carriage feed
handwheel hard to
move.
1. Dovetail ways loaded with shavings, dust,
or grime.
2. Gib screws are too tight.
3. Backlash setting too tight.
4. Bedways are dry.
1. Clean ways and re-lubricate.
Cutting tool
or machine
components vibrate
excessively during
cutting.
1. Tool holder not tight enough.
2. Cutting tool sticks too far out of tool holder;
lack of support.
3. Gibs are out of adjustment.
4. Dull cutting tool.
5. Incorrect spindle speed or feed rate.
1. Check for debris, clean, and re-tighten.
2. Re-install cutting tool so no more than 1⁄3 of the total
length is sticking out of tool holder.
3. Adjust gibs at affected component (see Page 61).
4. Replace or resharpen cutting tool.
5. Use the recommended spindle speed and feed rate.
-58-
2. Loosen gib screw(s) slightly (see Page 61).
3. Slightly loosen backlash setting (see Page 60).
4. Lubricate bedways/ball oilers.
Model G0602/G0752 (Mfd. Since 03/17)
Symptom
Possible Cause
Possible Solution
Workpiece is
tapered.
1. Headstock and tailstock are not properly
aligned with each other.
1. Re-align the tailstock to the headstock spindle
centerline (see Page 34).
Chuck jaws will
not move or do not
move easily.
1. Chips lodged in the jaws or scroll plate.
1. Remove jaws, clean and lubricate scroll plate and
jaws, then replace jaws.
Carriage will not
feed or is hard to
move.
1. Quick-change gears are not all engaged.
2. Half nut lever engaged.
3. Carriage lock is tightened down.
4.
5.
6.
7.
Quick-change gear
change dials will not
shift into position.
1. Adjust gear dials.
2. Disengage half nut lever for manual feeding.
3. Check to make sure the carriage lock bolt is fully
released.
4. Frequently clean away chips that load up during
Chips have loaded up on bedways.
turning operations and re-lubricate.
Bedways are dry and in need of lubrication. 5. Lubricate bedways/ball oilers.
6. Loosen gibs screw(s) slightly (see Page 61).
Gibs are too tight.
7. Replace gears or shear pin (see Page 62).
Gears or shear pin broken.
1. Gears not aligned inside headstock/quick
change gearbox.
Model G0602/G0752 (Mfd. Since 03/17)
1. Rotate spindle by hand with light pressure on the
dial until gear falls into place.
-59-
Backlash Adjustment
Backlash is the amount of free play felt while
changing rotation directions with the handwheel.
This can be adjusted on the compound rest and
cross slide leadscrews. Before beginning any
adjustment, make sure all associated components are cleaned and lubricated, and the locks
are loose.
Reducing backlash to less than 0.002" is
impractical and can lead to accelerated wear
to the leadscrew and other components.
Avoid the temptation to overtighten the
backlash nut or screw while adjusting.
Cross Slide
Tools Needed:
Qty
Hex Wrench 4mm............................................... 1
Hex Wrench 5mm ............................................. 1
Open-End Wrench 14mm................................... 1
The cross slide backlash is adjusted by loosening the cap screw shown in Figure 88. The
screw pushes down on a wedge and forces the
leadscrew nut apart, taking up lash between the
nut and leadscrew.
Cap Screw
Compound Rest
Tools Needed:
Qty
Hex Wrench 5mm............................................... 1
Open-End Wrench 10mm................................... 1
The compound rest backlash is adjusted by loosening or tightening the nut and set screw shown in
Figure 87 to remove play between the handwheel
and the leadscrew collar.
Set Screw
Nut
Figure 88. Cross slide backlash adjustment cap
screw.
To adjust the backlash, remove the compound
rest. Then, rock the cross slide handwheel back
and forth, and tighten the cap screw slowly until
the backlash is approximately 0.002"–0.003" as
indicated on the graduated dial.
If you end up adjusting the nut too tight, loosen
the cap screw, turn the handwheel back and forth
until it turns freely—then try again.
Re-install the compound rest when you are finished.
Figure 87. Compound rest backlash adjustment
set screws.
To adjust the backlash, loosen the compound rest
nut and set screw, turn the handwheel counterclockwise until the compound rest moves, then
tighten the nut until the backlash is approximately
0.002"–0.003", as indicated on the graduated dial.
Tighten the set screw to secure the setting.
-60-
Model G0602/G0752 (Mfd. Since 03/17)
Gib Adjustment
Compound Slide
Adjustment
Fasteners
The goal of adjusting the cross slide and compound slide gibs is to remove sloppiness or "play"
from the ways without making them overly stiff
and difficult to move.
In general, loose gibs cause poor finishes and
tool chatter; however, over-tightened gibs cause
premature wear and make the handwheels difficult to turn.
Tools Needed
Qty
Open-End Wrench 8mm.................................... 1
Hex Wrench 2.5mm............................................ 1
To adjust the cross slide and compound slide
gibs:
1. DISCONNECT LATHE FROM POWER!
2. Loosen the three hex nuts on the side of the
slide (see Figures 89–90).
Cross Slide
Adjustment
Fasteners
Figure 90. Compound slide gib adjustment hex
nuts and set screws.
3. Make adjustments in small and equal increments to the three set screws, then test
the movement of the slide by rotating the
handwheel.
Note: Turning the set screws clockwise will
tighten the gib, and turning them counterclockwise will loosen the gib.
4. When you are satisfied with the gib adjustment, keep the set screws from moving and
re-tighten the hex nuts to secure the settings.
5. Re-check the movement of the slide and, if
necessary, repeat Steps 2–4.
Figure 89. Cross slide gib adjustment hex nuts
and set screws.
Model G0602/G0752 (Mfd. Since 03/17)
-61-
Half Nut Adjustment
The clamping pressure of the half nut is fully
adjustable with a gib that can be loosened or
tightened by two set screws. Use this procedure
to adjust the half nut if it becomes loose from
wear, or it is too tight for your preferences. A half
nut that is too loose will make it difficult to produce
accurate work; one that is too tight will increase
the rate of wear on itself and the leadscrew.
Tools Needed
Qty
Open-End Wrench 8mm.................................... 1
Hex Wrench 5mm............................................... 1
Hex Wrench 2.5mm............................................ 1
Leadscrew Shear Pin
Replacement
The longitudinal leadscrew is secured to the feed
rate gearing in the headstock with the use of a
soft-metal shear pin (see Figure 92). The shear
pin is designed to break and disengage power
to the leadscrew to help protect more expensive
lathe components if you crash your carriage or
take too large of a cut and overload the lathe.
Contact Grizzly Customer Service at (570) 5469663 to order a replacement shear pin (Part #
P0602815).
To adjust the half nut:
1. DISCONNECT LATHE FROM POWER!
Shear Pin
2. Disengage the half nut, then remove the
thread dial.
3. Loosen the two adjustment hex nuts shown
in Figure 91, then adjust the set screws in
small, even increments so one end of the gib
does not become tighter than the other.
Connecting
Collar
Figure 92. Longitudinal leadscrew shear pin.
Half-Nut
Adjustment
Fasteners
Qty
Tools Needed
Hammer.............................................................. 1
Punch 2.5mm..................................................... 1
To replace the shear pin:
1. DISCONNECT LATHE FROM POWER!
Figure 91. Typical half nut gib adjustment.
4. Engage/disengage the half nut several times
and notice how it feels. The adjustment is
correct when the half nut has a slight drag
while opening and closing. The movement
should not be too stiff or too sloppy.
5. Repeat Steps 3–4, if necessary, until you are
satisfied with the half nut pressure.
6. While keeping the set screws from moving,
re-tighten the hex nuts, then re-install the
thread dial.
-62-
2. Rotate the leadscrew so the shear pin faces
up and down. If the connecting collar rotates
independently from the leadscrew, then
rotate the collar so the shear pin holes align
with those in the leadscrew.
3. Use the punch and hammer to drive out the
pieces of the old shear pin.
4. Make sure the holes in the collar and
leadscrew are aligned, then tap the new
shear pin completely through the holes in the
collar and leadscrew.
Model G0602/G0752 (Mfd. Since 03/17)
V-Belt Tension &
Replacement
Lock Bolt
V-Belts stretch and wear with use, so check the
tension on a monthly basis to ensure optimal
power transmission. Replace the V-belts if they
become cracked, frayed, or glazed.
On the Model G0602, the low range V-belt tension is controlled by a tensioner between the
secondary drive pulley (B) and spindle (C) pulley.
The high range V-belt between the spindle (C)
and motor (A) pulleys is tensioned by the motor.
On the Model G0752, V-belt tension is controlled
by a tensioner between the spindle and motor
pulleys.
Tensioner
Figure 94. Model G0752 tensioner and lock bolt.
4. Push the tensioner against the V-belt to tension it, then secure the tensioner.
The V-belt is correctly tensioned when there
is approximately 1⁄4" deflection when it is
pushed with moderate pressure, as shown in
Figure 95.
Qty
Tools Needed
Open-End Wrench 17mm................................... 1
Hex Wrench 5mm............................................... 1
Hex Wrench 8mm............................................... 1
Tensioning V-Belt
Pulley
Deflection
To tension the Model G0602 low range V-belt
or Model G0752 V-belt:
⁄4"
1
1. DISCONNECT LATHE FROM POWER!
Pulley
2. Open the change gear cover.
3. Loosen the tensioner lock nut (Model G0602)
or tensioner lock bolt (Model G0752) shown
in Figures 93–94.
Lock Nut
Tensioner
Figure 95. Correct V-belt deflection.
—If there is more than 1⁄4" deflection when the
V-belt is pushed with moderate pressure,
loosen the tensioner, adjust it so the tension is correct, then secure the tensioner.
5. Secure the change gear cover.
Figure 93. Model G0602 tensioner and lock nut.
Model G0602/G0752 (Mfd. Since 03/17)
-63-
To tension the Model G0602 high range
V-belt:
1. Follow Steps 1–3 in "Tensioning Timing Belt"
on Page 65.
2. Lower the motor and re-tighten the mounting
hex nuts. The high range V-belt is correctly
tensioned when there is approximately 1⁄4"
deflection when it is pushed with moderate
pressure, as shown in Figure 95 on Page 63.
—If the low range belt between pulleys B and
C (see Figure 97) needs to be replaced,
loosen the tensioner lock nut (see Figure
93 on Page 63), move the tensioner down,
roll the belt off the pulleys, then re-install
the new V-belt. Follow Steps 4-5 on Page
63 to tension the belt.
—If there is more than 1⁄4" deflection when
the V-belt is pushed with moderate pressure, loosen the motor mount nuts, lower
the motor as needed, then tighten the nuts.
3. Check the timing belt tension (refer to Step 5
of "Tensioning Timing Belt" on Page 65).
4. Secure the change gear cover.
Replacing V-Belt
1. DISCONNECT LATHE FROM POWER!
2. Open the change gear cover.
3. Model G0602:
—If the high range belt (Figure 96) needs to
be replaced, loosen the motor mount hex
nuts, (see Figure 99 on Page 65), raise
the motor, and carefully roll the belt off of
pulleys A and C. Install a new V-belt, then
follow the steps in "To tension the Model
G0602 high range V-belt" above.
C
C
B
Tensioner
Figure 97. Model G0602 low-range belt.
Model G0752:
Loosen the tensioner lock bolt, then pivot the
tensioner to the left and secure it temporarily.
Remove the V-belt (see Figure 98) and re-install
the new one. Follow Steps 4-5 on Page 63 to tension the belt.
Lock Bolt
Tensioner
V-Belt
Figure 98. Model G0752 V-Belt.
A
High
Range Belt
Figure 96. Model G0602 high-range belt.
-64-
Model G0602/G0752 (Mfd. Since 03/17)
Timing Belt Tension
& Replacement
Pulley
Deflection
On the Model G0602 the timing belt transfers
power from the motor to the secondary drive pulley (see Figure 99). If the timing belt becomes
excessively worn or damaged, you will need to
replace it.
1
Pulley
Figure 100. Correct timing-belt deflection.
Motor
Mount
Hex Nuts
(2 of 4)
—If there is more than 1⁄4" deflection when
the belt is pushed with moderate pressure,
loosen the motor mount nuts, lower the
motor, adjust belt tension as required, then
tighten the nuts.
—If the high range V-belt is installed, check
the V-belt tension. Refer to "To tension the
Model G0602 high range V-belt" instructions on Page 64.
Timing
Belt
Figure 99. Timing belt and motor mount hex
nuts.
Tools Needed
Qty
Hex Wrench 5mm............................................... 1
Open-End Wrench 14mm................................... 1
Tensioning Timing Belt
1. DISCONNECT LATHE FROM POWER!
2. Open the change gear cover.
3. Loosen the motor mount hex nuts (see
Figure 99).
Note: It may be more convenient to access
the motor mount hex nuts if you first remove
the rear splash guard.
4. Lower the motor and re-tighten the mounting
hex nuts.
5. Check the timing belt tension: It is correctly
tensioned when there is approximately 1⁄4"
deflection when it is pushed with moderate
pressure, as shown in Figure 100.
Model G0602/G0752 (Mfd. Since 03/17)
⁄4"
6. Secure the change gear cover.
Replacing Timing Belt
1. DISCONNECT LATHE FROM POWER!
2. Open the change gear cover.
3. Loosen the four motor mount hex nuts (see
Figure 99) then remove the low or high range
V-belt (refer to Replacing V-Belt on Page
64).
Note: It may be more convenient to access
the motor mount hex nuts if you first remove
the rear splash guard.
4. Raise the motor up, roll the old timing belt
off the pulleys and replace it with a new one,
making sure that the belt teeth are seated in
the pulley indents.
5. Re-install the high or low range V-Belt—
depending upon your setup (refer to
Replacing V-Belt on Page 64).
6. Tension the timing belt and V-belt. Refer to
Tensioning Timing-Belt on this page, and
the instructions for tensioning the applicable
V-belt on Pages 63– 64.
-65-
machine
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous.
Touching electrified parts will result in personal
injury including but not limited to severe burns,
electrocution, or death. Disconnect the power
from the machine before servicing electrical components!
MODIFICATIONS. Modifying the wiring beyond
what is shown in the diagram may lead to unpredictable results, including serious injury or fire.
This includes the installation of unapproved aftermarket parts.
WIRE CONNECTIONS. All connections must
be tight to prevent wires from loosening during
machine operation. Double-check all wires disconnected or connected during any wiring task to
ensure tight connections.
CIRCUIT REQUIREMENTS. You MUST follow
the requirements at the beginning of this manual
when connecting your machine to a power source.
WIRE/COMPONENT DAMAGE. Damaged wires
or components increase the risk of serious personal injury, fire, or machine damage. If you notice
that any wires or components are damaged while
performing a wiring task, replace those wires or
components.
MOTOR WIRING. The motor wiring shown in
these diagrams is current at the time of printing
but may not match your machine. If you find this
to be the case, use the wiring diagram inside the
motor junction box.
CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical charge for
up to 10 minutes after being disconnected from
the power source. To reduce the risk of being
shocked, wait at least this long before working on
capacitors.
EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information
included in this section, contact our Technical
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.
-66-
Model G0602/G0752 (Mfd. Since 03/17)
G0602 Wiring Diagram
V2
L N
L
A1
1L1
N
N
3L2
3
L
U2
L
W1
4
44
A2
3
4
Run Capacitor
20MFD 450VAC
6T3
V1
2
6
10
4
8
12
3
W2
U1
Front
View
3
1 NC
2
U1
4
MINGER
LA125H-BE101C
MINGER
LA125H-BE101C
Start Capacitor
150 MFD 250VAC
14NO 22NC 32 NC 44 NO
N
V1
V2
3TB41
V1 Gnd
W2 U2
4 NO
W1
W2
V1
L
5L3
22E KM1
L
N
Ground
Siemens
4T2
4
V1 4
13NO 21NC 31NC 43NO
2T1
L
3
L
N
3
Start
Button
Switch
7
11
CANSEN LW26-20
1
5
9
Rear
View
E-Stop
Button
Switch
L
Rotary
Switch
Wiring Box
(Shown from behind) Control Panel
Motor 1HP 110V
Neutral
W2
Hot
U1
V2
V1
W1
110 VAC
5-15 Plug
(As Recommended)
Ground
Ground
Model G0602/G0752 (Mfd. Since 03/17)
U2
READ ELECTRICAL SAFETY
ON PAGE 66!
-67-
G0602 Electrical Components
Figure 101. Spindle direction switch and ON
button.
Figure 104. Spindle direction switch and
emergency stop switch.
Figure 102. Electrical box.
Figure 105. Magnetic contactor.
Figure 103. Motor connection detail.
-68-
READ ELECTRICAL SAFETY
ON PAGE 66!
Model G0602/G0752 (Mfd. Since 03/17)
G0752 Wiring Box Diagram
To Control Panel
Page 71
PE
4 1
2 3
To Circuit Board
Page 71
To Variable-Speed
Switch Page 71
10V
5
DCM
N
1
1L1
M1
N1
L1
A1
M2
ACM
AVI
1
L
To Spindle Direction
Switch Page 71
3L2
R/L1 S/L2 T/L3
5L3
1
13NO 21NC 31NC 43NO
Contactor
READY
Siemens
L1
6T3
1 23
Delta
VFD007E11A
14NO 22NC 32 NC 44 NO
3
4T2
ON
FAULT
VS Drive
22E KM1
3TB41
2T1
RUN
N1
N1
A2
0
0
AVI
ACI
NPN
PNP
RB
RA
RC
MCM
AFM
M01
8
MI2
L1 N1
4
4
L
N
L
N
MI4
MI3
MI6
MI5
DCM ACM
DCM 24V
AVI 10V
AC1
1
L1 N1
L
MI1
6
5
DCM
DCM
M1 M2
2A
Relay
RS-485
Port
10V
ACM AVI
U/T1 V/T2 W/T3 +/B1
OMRON
MY2N-J 220V
B2
DCM
L
2
L1 N1
L1 N1
N
12
9
14
13
0
5
U1
V1
W1
5
PE
L
N
0
110
220
PE
PE
Transformer
PE
BEIJING AOHENGDA ELECTRICAL
JBK5-40VA
V1
L1
N1
0
24
0
8
U1
PE
W1
To Left Motor To Right Motor Junction Box Junction Box Page 73
Page 73
Model G0602/G0752 (Mfd. Since 03/17)
PE
N L
Wiring Box
To Power Supply
Page 73
READ ELECTRICAL SAFETY
ON PAGE 66!
-69-
G0752 Wiring Box Components
Figure 106. G0752 electrical box.
-70-
READ ELECTRICAL SAFETY
ON PAGE 66!
Model G0602/G0752 (Mfd. Since 03/17)
G0752 Control Panel Wiring Diagram
To Wiring Box
Page 69
To Wiring Box
Page 69
Spindle Speed
Circuit Board
To Wiring Box
Page 69
Spindle
Speed
Sensor
See Figure 110,
Page 72
See Figure 112,
on Page 72
VS Dial
(Potentiometer)
See
Figure 109,
Page 72
WXD3-13
M
CA
ACM
10V
IAVVI
A
2
M
DCM
CD
3
1
(Top)
4
M
1M
1
PE
5
RPM Display
M
2M
2
See Figure 108, Page 72
(Bottom)
2
COM
1
3
1 NC
5
4 4
3 NO
4
M2
4
3 NO
LA252HBE101C
2
2
LA252HBE101C
1 NC
LA252HBE102C
LA252HBE102C
P
EE
P
2
DCM
1 NC
3 NO
1 NC
2
4
1
3
LA252HBE101C
LA252HBE102C
Ground
4
LA252HBE102C
M1
Spindle
Direction
Switch
OFF Button
Switch
ON Button
Switch
E-Stop
Button Switch
Control Panel
(Viewed from Behind)
See Figure 107, on Page 72
Model G0602/G0752 (Mfd. Since 03/17)
READ ELECTRICAL SAFETY
ON PAGE 66!
-71-
G0752 Control Panel Components
Spindle
Direction
Switch
E-Stop
Button
Switch
ON Button
Switch
OFF
Button
Switch
Figure 107. Control panel.
Figure 108. RPM display.
Figure 111. Right junction box.
Figure 109. Variable-speed dial.
Figure 112. Spindle speed sensor.
Figure 110. Spindle speed circuit board.
-72-
READ ELECTRICAL SAFETY
ON PAGE 66!
Model G0602/G0752 (Mfd. Since 03/17)
G0752 Motor Wiring Diagram
Motor 1HP 220V 3PH
Motor Fan
110V 30W 1PH
110 VAC
5-15 Plug
(As Recommended)
Neutral
N1
Hot
L1
U1
V1
W1
Ground
Ground
PE
To Wiring
Box
Page 69
To Wiring
Box
Page 69
Figure 113. Left motor junction box.
Model G0602/G0752 (Mfd. Since 03/17)
L
PE
N
To Wiring
Box
Page 69
Figure 114. Right motor junction box.
-73-
SECTION 9: PARTS
Spindle & Drive Belt
1
5
6
7
8
64
3
60
62
57
54-3
2
10
11
63
69
12
70
15
14
13
71
4
72
54-4
56
28
16
26
19-1
(G0752)
22
27
13 17
19
20 21 (G0602)
29
30
25
54
54-2
54-1
24 23
55-2
31
32
(G0602) 33
34
(G0752)
(G0602)
41
43 42
35
40
41
40
42
LEFT REAR VIEW
49
36
37
(G0602)
18
39
37
(G0752)
37
38
55-3
55-1
44
46
47
48
-74-
51
45
51
53
52
55
Model G0602/G0752 (Mfd. Since 03/17)
Spindle & Drive Belt Parts
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
18
19
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
HEADSTOCK REAR COVER
PHLP HD SCR M4-.7 X 6
DEAD CENTER MT#4
BALL OILER 7MM PRESS-IN
CAP SCREW M6-1 X 25
FLAT WASHER 6MM
COMPRESSION SPRING
CLAMP
CAP SCREW M6-1 X 25
SPINDLE
KEY 10 X 10 X 55
SPACER
TAPERED ROLLER BEARING 32009
HEADSTOCK
CAP SCREW M8-1.25 X 20
TAPERED ROLLER BEARING 32009
CAP SCREW M6-1 X 20
SPACER
SPEED SENSOR RING W/MAGNETS
GEAR 40T PLASTIC
V-BELT M-27.5 3L275 (G0602)
PULLEY C
V-BELT M-33 3L330
SPANNER NUT 37MM
BRACKET PLATE
LOCK WASHER 10MM
HEX NUT M10-1.5
FLAT WASHER 10MM
CAP SCREW M5-.8 X 10
FLAT WASHER 5MM
GEAR SHAFT
TIMING BELT 263L (G0602)
BALL BEARING 6001ZZ (G0602)
TIMING PULLEY (G0602)
INT RETAINING RING 12MM (G0602)
SPACER
37
37
38
39
40
40
41
42
43
44
45
46
48
49
51
52
53
54
54-1
54-2
54-3
54-4
55
55-1
55-2
55-3
56
57
60
62
63
64
69
70
71
72
PULLEY A (G0602)
MOTOR PULLEY (G0752)
KEY 6 X 6 X 40
SPACER
STANDOFF STUD M10-1.5 X 50, 15, 25 (G0602)
CAP SCREW M10-1.5 X 20 (G0752)
MOUNTING PLATE
FLAT WASHER 10MM
HEX NUT M10-1.5 (G0602)
TENSIONER ROLLER SHAFT
BALL BEARING 6001-2RS
TENSIONER ROLLER
EXT RETAINING RING 12MM
CHANGE GEAR COVER
HEX NUT M5-.8
SPINDLE COVER
PHLP HD SCR M5-.8 X 12
3-JAW CHUCK 5"
3-JAW CHUCK JAW INT 3-PC SET
CHUCK BACKPLATE
3-JAW CHUCK KEY
3-JAW CHUCK JAW EXT 3-PC SET
4-JAW CHUCK 6.5"
4-JAW CHUCK JAWS 4-PC SET
4-JAW CHUCK KEY
4-JAW CHUCK BACKPLATE
FACEPLATE 8"
DEAD CENTER MT#3
TOOL BOX, EMPTY
HEX WRENCH SET (2.5,3,4,5,6MM)
WRENCH SET (8-10, 12-14, 17-19MM)
BOTTLE FOR OIL
STANDARD SCREWDRIVER #1
PHILLIPS SCREWDRIVER #1
SPINDLE CLAMP
CAP SCREW M6-1 X 20
P0602001
P0602002
P0602003
P0602004
P0602005
P0602006
P0602007
P0602008
P0602010
P0602011
P0602012
P0602013
P0602014
P0602015
P0602016
P0602017
P0602018
P0602019
P0752019
P0602020
P0602021
P0602022
P0602023
P0602024
P0602025
P0602026
P0602027
P0602028
P0602029
P0602030
P0602031
P0602032
P0602033
P0602034
P0602035
P0602036
P0602037
P0752037
P0602038
P0602039
P0602040
P0752040
P0602041
P0602042
P0602043
P0602044
P0602045
P0602046
P0602048
P0602049
P0602051
P0602052
P0602053
P0602054
P0602054-1
P0602054-2
P0602054-3
P0602054-4
P0602055
P0602055-1
P0602055-2
P0602055-3
P0602056
P0602057
P0602060
P0602062
P0602063
P0602064
P0602069
P0602070
P0602071
P0602072
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
Model G0602/G0752 (Mfd. Since 03/17)
-75-
Apron
108 109
104
105
106
110
111
113
112
114
107
116
115
135
103
102
118
131
130
137
146
134V2
117
119
120
121
122
123
124
125
126
136V2
145 144
101
142
140
138
141 139
126-1
127
143 133V2
132
128
129
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
ROLL PIN 4 X 14
HALF-NUT 2-PC
DOWEL PIN 5 X 12
GEAR SHAFT
GEAR
ROLL PIN 4 X 30
APRON CASTING
CAP SCREW M4-.7 X 12
HALF-NUT GIB
DOWEL PIN 4 X 16
SET SCREW M5-.8 X 16
SET SCREW M6-1 X 25
HEX NUT M5-.8
SET SCREW M6-1 X 12
HALF-NUT LEVER HUB
HALF-NUT LEVER STUD
HALF-NUT LEVER HANDLE
STEEL BALL 5MM
CAP SCREW M6-1 X 6
THREAD DIAL
RIVET 2 X 5MM STEEL FLUTED
POINTER
SHAFT
124
125
126
126-1
127
128
129
130
131
132
133V2
134V2
135
136V2
137
138
139
140
141
142
143
144
145
146
P0602124
P0602125
P0602126
P0602126-1
P0602127
P0602128
P0602129
P0602130
P0602131
P0602132
P0602133V2
P0602134V2
P0602135
P0602136V2
P0602137
P0602138
P0602139
P0602140
P0602141
P0602142
P0602143
P0602144
P0602145
P0602146
KEY 3 X 3 X 10
CAP SCREW M6-1 X 55
THREAD DIAL BODY
THREAD DIAL ASSY
SIDE GEAR 48T
FLAT WASHER 8MM
HEX NUT M8-1.25
SET SCREW M6-1 X 6
COMPRESSION SPRING
CARRIAGE HANDWHEEL HANDLE
CARRIAGE HANDWHEEL
SET SCREW M6-1 X 12
SET SCREW M6-1 X 12 CONE-PT
GEAR SHAFT V2.03.17
FLAT HD SCR M6-1 X 10
FLAT WASHER 6MM
HALF-NUT INDICATOR PLATE
LOCK CAM SHAFT
THREADED DIAL PLATE
HALF-NUT BRACKET
PLATE SPRING
GRADUATED DIAL
ROLL PIN 5 X 12
KEY 3 X 3 X 12
-76-
P0602101
P0602102
P0602103
P0602104
P0602105
P0602106
P0602107
P0602108
P0602109
P0602110
P0602111
P0602112
P0602113
P0602114
P0602115
P0602116
P0602117
P0602118
P0602119
P0602120
P0602121
P0602122
P0602123
Model G0602/G0752 (Mfd. Since 03/17)
Tool Post & Compound Rest
218
219
222
212
221
207
211
220A
220
201
210
215
216
208
208
203
206
202
217
228
209
224
204
229
226
227
205
214
213
223
225 230
231
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
COMPOUND REST
SWIVEL BASE
COMPOUND REST GIB
CLAMPING RING
GRADUATED DIAL
BARREL NUT
DOWEL PIN
TOOL POST BOLT
FLAT WASHER 8MM
DOWEL PIN
COMPRESSION SPRING
CAP SCREW M8-1.25 X 30
CAP SCREW M8-1.25 X 25
CAP SCREW M6-1 X 12
SET SCREW M5-.8 X 16
HEX NUT M5-.8
217
218
219
220A
220
221
222
223
224
225
226
227
228
229
230
231
HEX BOLT M8-1.25 X 30
TOOL POST HANDLE
TOOL POST HANDLE HUB
4-WAY TOOL POST ASSEMBLY
TOOL REST
HUB SPACER
TOOL REST SLIDE PLATE
COMPOUND REST LEADSCREW
LEADSCREW MOUNT
GRADUATED DIAL
COMPOUND REST HANDWHEEL
COMPOUND HANDWHEEL HANDLE
KEY 3 X 3 X 8
POINTER
THREADED COLLAR
SET SCREW M8-1.25 X 6
P0602201
P0602202
P0602203
P0602204
P0602205
P0602206
P0602207
P0602208
PW01M
P0602210
P0602211
PCAP13M
PCAP31M
PCAP26M
PSS34M
PN06M
Model G0602/G0752 (Mfd. Since 03/17)
PB26M
P0602218
P0602219
P0602220A
P0602220
P0602221
P0602222
P0602223
P0602224
P0602225
P0602226
P0602227
PK03M
P0602229
P0602230
PSS17M
-77-
Tailstock
300
306
307
308
320
319
304
317
301
302
316
303
312
309
310
305
322
311
318
325
324
313
315
314
321
314
319
323
326
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
300
301
302
303
304
305
306
307
308
309
310
311
312
313
COMPLETE TAILSTOCK ASSY
TAILSTOCK QUILL
TAILSTOCK LEADSCREW
BUSHING
HANDWHEEL SCALE PLATE
TAILSTOCK HANDWHEEL
LEVER BOLT M12-1.75 X 50
BARREL NUT M12-1.75
SET SCREW M6-1 X 12
GRADUATED DIAL
TAILSTOCK HANDWHEEL POINTER
HANDWHEEL BUSHING
TAILSTOCK BODY
TAILSTOCK BASE
314
315
316
317
318
319
320
321
322
323
324
325
326
SET SCREW M8-1.25 X 25
TAILSTOCK HANDWHEEL HANDLE
UPPER OFFSET PLATE
KEY 3 X 3 X 10
LOCK NUT M10-1.5
RIVET 2 X 5MM STEEL FLUTED
BALL OILER 10MM
CLAMPING PLATE
HEX NUT M12-1.75
HEX BOLT M12-1.75 X 90
FLAT WASHER 12MM
SET SCREW M5-.8 X 6
LOWER OFFSET PLATE
-78-
P0602300
P0602301
P0602302
P0602303
P0602304
P0602305
P0602306
P0602307
PSS04M
P0602309
P0602310
P0602311
P0602312
P0602313
PSS21M
P0602315
P0602316
PK39M
PLN05M
PRIV001M
P0602320
P0602321
PN09M
PB158M
PW06M
PSS26M
P0602326
Model G0602/G0752 (Mfd. Since 03/17)
Bed & Leadscrew
413
414
409
412
411
410
401
402
403
415
404 407 406
405
408
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
406
407
408
BED
RACK
CAP SCREW M5-.8 X 12
LONGITUDINAL LEADSCREW
LEADSCREW END BRACKET
BALL OILER 6MM
CAP SCREW M6-1 X 20
LOCK NUT M10-1.5
409
410
411
412
413
414
415
BACK SPLASH
STUD-SE M10-1.5 X 45, 35
HEX NUT M10-1.5
SET SCREW M8-1.25 X 40
FLAT WASHER 8MM
HEX NUT M8-1.25
CHIP PAN
P0602401
P0602402
PCAP33M
P0602404
P0602405
P0602406
PCAP02M
PLN05M
Model G0602/G0752 (Mfd. Since 03/17)
P0602409
P0602410
PN02M
PSS44M
PW01M
PN03M
P0602415
-79-
Steady Rest & Follow Rest
506
503
504
505
501
502
501A
510
509
514
507 508
512
513
516
511
515
511A
517
518
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501A
501
502
503
504
505
506
507
508
509
STEADY REST ASSEMBLY
STEADY REST CASTING
FINGER
SHOULDER T-BOLT
LOCK WASHER 6MM
HEX NUT M6-1
ADJUSTING SCREW
CLAMPING PLATE
HEX BOLT M12-1.75 X 65
FLAT WASHER 12MM
510
511A
511
512
513
514
515
516
517
518
HEX NUT M12-1.75
FOLLOW REST ASSEMBLY
FOLLOW REST CASTING
FINGER
SHOULDER T-BOLT
ADJUSTING SCREW
HEX NUT M6-1
LOCK WASHER 6MM
CAP SCREW M8-1.25 X 35
FLAT WASHER 8MM
-80-
P0602501A
P0602501
P0602502
P0602503
PLW03M
PN01M
P0602506
P0602507
PB125M
PW06M
PN09M
P0602511A
P0602511
P0602502
P0602503
P0602506
PN01M
PLW03M
PCAP40M
PW01M
Model G0602/G0752 (Mfd. Since 03/17)
G0602 Motor & Electrical
611V2-1
611V2-6
611V2-2
602
603
617
604
611V2-3
601
611V2-5
607
608
611V2-7
611V2
610
616
611V2-4
612
615
619
618
620
621
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
601
602
603
604
607
608
610
611V2
611V2-1
611V2-2
611V2-3
611V2-4
P0602601
PCAP06M
PLW03M
P0602604
P0602607
P0602608
PS17M
P0602611V2
P0602611V2-1
P0602611V2-2
PC150
P0602611V2-4
ELECTRICAL CABINET
CAP SCREW M6-1 X 25
LOCK WASHER 6MM
ELECTRICAL CABINET COVER
STRAIN RELIEF NUT
STRAIN RELIEF M25-1.5
PHLP HD SCR M4-.7 X 6
MOTOR 1HP 110V 1-PH ALUM BDY V2.09.08
MOTOR FAN V2.09.08
MOTOR FAN COVER V2.09.08
S CAPACITOR 150M 125V
R CAPACITOR 20M 400V
611V2-5
611V2-6
611V2-7
612
615
616
617
618
619
620
621
P0602611V2-5
P0602611V2-6
P0602611V2-7
PW05M
P0602615
P0602616
P0602617
P0602618
P0602619
P0602620
P0602621
CAPACITOR COVER V2.09.08
POWER CORD 14G 3W 60" 5-15P
MOTOR JUNCTION BOX
FLAT WASHER 4MM
STRAIN RELIEF M20-1.5
STRAIN RELIEF NUT
CONTACTOR SIEMENS 3TB41 22E 110V
E-STOP BUTTON MINGER LA125H-BE102C
ON PUSH BUTTON MINGER LA125H-BE101C
ROTARY SWITCH CANSEN LW26-20 M09T/3
G0602 CONTROL PANEL
Model G0602/G0752 (Mfd. Since 03/17)
-81-
G0752 Motor & Electrical
611-3
629
611-4
611-6
628V2
627
611-1
611-2
623
626
624
622
611
625
602
601
4
6
1
5
KA
I
DY
F08
630
A
617
603
604
618
612
619
610
633
632
631
620
634
621
607
608
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
601
602
603
604
607
608
610
611
611-1
611-2
611-3
611-4
611-6
612
617
618
619
ELECTRICAL CABINET
CAP SCREW M6-1 X 25
LOCK WASHER 6MM
ELECTRICAL CABINET COVER
STRAIN RELIEF NUT
STRAIN RELIEF M25-1.5
PHLP HD SCR M4-.7 X 6
MOTOR 1HP 220V 3-PH
MOTOR FAN
MOTOR FAN COVER
RIGHT MOTOR JUNCTION BOX COVER
LEFT MOTOR JUNCTION BOX COVER
POWER CORD 16G 3W 60" 5-15P
FLAT WASHER 4MM
CONTACTOR SIEMENS 3TB41 22E 24V
TRANSFORMER BAEEC JBK5-40VA
TERMINAL POST
620
621
622
623
624
625
625
626
627
628V2
629
630
631
632
633
634
P0752620
P0752621
P0752622
P0752623
P0752624
P0752625
P0752625
P0752626
P0752627
P0752628V2
P0752629
P0752630
P0752631
P0752632
P0752633
P0752634
INVERTER (VFD) DELTA VFD007E11A
VFD-E USER MANUAL
E-STOP BUTTON MINGER LA125H-BE101C-102C
ON PUSH BUTTON MINGER LA125H-BE102C
SPINDLE DIRECTION SWITCH LA125H-BE102C
G0752 CONTROL PANEL
G0752 CONTROL PANEL
OFF PUSH BUTTON MINGER LA125H-BE101C
RPM DISPLAY UNIT
POTENTIOMETER WXD3-13 V2.03.17
SPINDLE SPEED SENSOR
RELAY OMRON MY2N-J 220V
FUSE 2A 250V
FUSE HOLDER
TERMINAL POST MOUNTING BRACKET
GROUNDING BAR
-82-
P0752601
P0752602
P0752603
P0752604
P0752607
P0752608
P0752610
P0752611
P0752611-1
P0752611-2
P0752611-3
P0752611-4
P0752611-6
P0752612
P0752617
P0752618
P0752619
Model G0602/G0752 (Mfd. Since 03/17)
Change Gears
701
704
707
703
702
708
706
719
718 714
717
715
712
716
713
735
711
736
737
739
740
741
728
729
730
731
732
733
734
725
723
720
722
721
724
726
727
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
701
702
703
704
706
707
708
711
712
713
714
715
716
717
718
719
720
721
722
SET SCREW M6-1 X 10
KEYED BUSHING
GEAR 60T PLASTIC
GEAR 27T CAST-IRON
GEAR SHAFT
E-CLIP 9MM
BALL OILER 6MM
BRACKET
T-NUT
SPACER WASHER
GEAR SHAFT
KEYED BUSHING
GEAR 127T
GEAR 56T
GEAR SHAFT CLIP
BALL OILER 6MM
BUSHING
KEY 4 X 4 X 14
SPACER RING
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
GEAR 104T
FLAT WASHER 6MM
CAP SCREW M6-1 X 6
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 40
GEAR 36T
GEAR 36T
GEAR 40T
GEAR 44T
GEAR 46T
GEAR 48T
GEAR 52T
GEAR 45T
GEAR 56T
GEAR 60T
GEAR 60T PLASTIC
GEAR 104T
GEAR 120T
GEAR 127T
PSS01M
P0602715
P0602703
P0602704
P0602706
PEC10M
P0602708
P0602711
P0602712
P0602713
P0602714
P0602715
P0602716
P0602717
P0602718
P0602708
P0602720
PK97M
P0602722
Model G0602/G0752 (Mfd. Since 03/17)
P0602723
PW03M
PCAP85M
PLW04M
PCAP12M
P0602728
P0602729
P0602730
P0602731
P0602732
P0602733
P0602734
P0602735
P0602736
P0602737
P0602703
P0602739
P0602740
P0602741
-83-
Gearbox
801
802
803
804
805
806
813
805
807
808
802
812
809
811
810
814
826
825
822
823
823
833
832
822
820
819
820
824
831
822
818
817
815
821
830
822
829
828
816
827
835
834
836
837
846 847
838
844
845
848
849
850
843
841
842
840
839
-84-
Model G0602/G0752 (Mfd. Since 03/17)
Gearbox Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
PLUG
O-RING
BUSHING
CLUSTER GEAR 30/36/33T
KEY 4 X 4 X 50
GEAR SHAFT
BUSHING
CLUSTER GEAR 22/44/33T
CLUSTER GEAR PLUG
CAP SCREW M5-.8 X 10
REAR GEARBOX COVER
FILL PLUG 3/8" NPT
GEAR BOX CASE
DRAIN PLUG 3/8" NPT
SHEAR PIN 5 X 20
LEADSCREW CONNECTING COLLAR
SHEAR PIN 5 X 20
CAP SCREW M6-1 X 12
FLANGE
BALL BEARING 6202-OPEN
GEAR 33T
EXT RETAINING RING 15MM
KEY 4 X 4 X 8
GEAR SHAFT 22T
GEAR 44T
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
COLLAR
KEY 4 X 4 X10
GEAR SHAFT
GEAR 33T
GEAR 30T
GEAR 35T
FLANGE
CAP SCREW M6-1 X 16
SHIFT FORK
FRONT GEARBOX COVER
ROLL PIN 5 X 30
COMPRESSION SPRING
SIGHT GLASS A16
POINTER DISC
SET SCREW M6-1 X 10
STEEL BALL 5MM
SHIFT HUB
SET SCREW M6-1 X 10
CAP SCREW M6-1 X 50
CAP SCREW M6-1 X 20
O-RING 1.8 X 6.7
SHAFT
ROLL PIN 5 X 20
SHIFT LEVER
SHIFT FORK
P0602801
P0602802
P0602803
P0602804
PK133M
P0602806
P0602807
P0602808
P0602809
PCAP50M
P0602811
P0602812
P0602813
P0602814
P0602815
P0602816
P0602817
PCAP26M
P0602819
P6202-OPEN
P0602821
PR05M
PK65M
P0602824
P0602825
Model G0602/G0752 (Mfd. Since 03/17)
P0602826
PK132M
P0602828
P0602829
P0602830
P0602831
P0602832
PCAP01M
P0602834
P0602835
PRP05M
P0602837
P0602838
P0602839
PSS01M
PSTB004M
P0602842
PSS01M
PCAP37M
PCAP02M
P0602846
P0602847
PRP03M
P0602849
P0602850
-85-
Cross Slide & Carriage
915
910
903
909
907
908
919
920
906
902A
921
922
923
904
905
918
924
925
926
934
935
933
939
916
914
911
913 912
937
917 938 936
929
927
901 928
931
930
932
REF
PART #
DESCRIPTION
REF PART #
DESCRIPTION
901
902A
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
P0602901
P0602902A
P0602903
P0602904
P0602905
P0602906
PCAP31M
P0602908
PRIV001M
P0602910
PK105M
P0602912
P0602913
P0602914
PSS17M
P0602916
P0602917
P0602918
PCAP26M
PSS11M
SADDLE
CROSS SLIDE W/O T-SLOTS V2.08.07
CROSS SLIDE GIB
CROSS SLIDE LEADSCREW NUT
CROSS SLIDE LEADSCREW
LEADSCREW BRACKET
CAP SCREW M8-1.25 X 25
INDICATOR PLATE
RIVET 2 X 5MM STEEL FLUTED
GRADUATED DIAL
KEY 3 X 3 X 6
SPRING PLATE
CROSS SLIDE HANDWHEEL
HANDWHEEL HEX NUT
SET SCREW M8-1.25 X 6
CROSS SLIDE HANDWHEEL HANDLE
SLIDE BLOCK
CHIP GUARD
CAP SCREW M6-1 X 12
SET SCREW M6-1 X 16
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
DOWEL PIN
SET SCREW M5-.8 X 16
HEX NUT M5-.8
SADDLE TENSION BAR
FLAT WASHER 6MM
CAP SCREW M6-1 X 16
SADDLE CLAMP PLATE
SET SCREW M6-1 X 20
HEX NUT M6-1
CAP SCREW M6-1 X 35
V-WAY WIPER
V-WAY WIPER COVER
PHLP HD SCR M4-.7 X 8
STRAIGHT WAY WIPER
STRAIGHT WAY WIPER COVER
BALL OILER 6MM
CAP SCREW M8-1.25 X 35
CAP SCREW M6-1 X 35
HANDLE SCREW
-86-
P0602921
PSS34M
PN06M
P0602924
PW03M
PCAP01M
P0602927
PSS25M
PN01M
PCAP48M
P0602931
P0602932
PS07M
P0602934
P0602935
P0602936
PCAP40M
PCAP48M
P0602939
Model G0602/G0752 (Mfd. Since 03/17)
./4)#%
-/$%,'8,!4(%
-/$%,'8,!4(%
$!-!'%7),,/##52)&
-/4/2(063).',%0(!3%
#!22)!'%&%%$3).4/
37).'/6%2"%$
(%!$34/#+/24!),34/#+
37).'/6%2#2/333,)$%
-/4/2(063).',%0(!3%
#2/333,)$%42!6%,
37).'/6%2"%$
#!22)!'%42!6%,
37).'/6%2#2/333,)$%
,%!$3#2%7840)
$)34!.#%"%47%%.#%.4%23
-!8)-5-4//,3):%8
30).$,%"/2%
7%)'(4,"3
30).$,%4!0%2-4
30).$,%4(2%!$840)
4!),34/#+4!0%2-4
4!),34/#+42!6%,
#/-0/5.$42!6%,
CALL
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
0%23/.!,).*529
#2/333,)$%42!6%,
#!22)!'%42!6%,
,%!$3#2%7840)
-!8)-5-4//,3):%8
2%!$AND5.$%234!.$
7%)'(4,"3
7!2.).'
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
2%!$AND5.$%234!.$
$)34!.#%"%47%%.#%.4%23
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
30).$,%"/2%
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
INSTRUCTIONMANUALTO
INSTRUCTIONMANUALTO
(!)2!.$"544/.!,,,/.'3,%%6%3()243
30).$,%4!0%2-4
AVOIDSERIOUSINJURY)FA
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
AVOIDSERIOUSINJURY)FA
30).$,%4(2%!$840)
MANUALISNOTAVAILABLE
$/./4%80/3%4/2!)./2$!-0.%33
4!),34/#+4!0%2-4
MANUALISNOTAVAILABLE
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
$/./4USEMACHINE'O
4!),34/#+42!6%,
$/./4USEMACHINE'O
7(%.4)2%$
#/-0/5.$42!6%,
TOWWWGRIZZLYCOMOR
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
TOWWWGRIZZLYCOMOR
CALL"%&/2%34!24).'-/4/2
CALL
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
/.&,!4,%6%,'2/5.$
#!22)!'%42!6%,
&!),52% 4/ &/,,/7 4(%3% 37).'/6%2"%$
7!2.).'3 7),, 2%35,4 ). 3%2)/53
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),,
2%35,4 ). 3%2)/53
,%!$3#2%7840)
37).'/6%2#2/333,)$%
0%23/.!,).*529
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
0%23/.!,).*529
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
-!8)-5-4//,3):%8
$)34!.#%"%47%%.#%.4%23
2%!$AND5.$%234!.$
%.4!.',%-%.4
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
7%)'(4,"3
30).$,%"/2%
INSTRUCTIONMANUALTO
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
(!:!2$ 30).$,%4!0%2-4
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
AVOIDSERIOUSINJURY)FA
30).$,%4(2%!$840)
4IEBACKLONGHAIRROLLUP
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
4!),34/#+4!0%2-4
MANUALISNOTAVAILABLE
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
LONGSLEEVESANDREMOVE
(!)2!.$"544/.!,,,/.'3,%%6%3()243
4!),34/#+42!6%,
(!)2!.$"544/.!,,,/.'3,%%6%3()243$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
$/./4USEMACHINE'O
LOOSECLOTHINGJEWELRYOR
#/-0/5.$42!6%,
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
$/./4%80/3%4/2!)./2$!-0.%33
TOWWWGRIZZLYCOMOR
GLOVESTOPREVENTGETTING
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
$/./4%80/3%4/2!)./2$!-0.%33
7(%.4)2%$
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
CAUGHTINMOVINGPARTS
CALL
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
7(%.4)2%$
"%&/2%34!24).'-/4/2
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
"%&/2%34!24).'-/4/2
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
$!-!'%7),,/##52)&
0%23/.!,).*529
/.&,!4,%6%,'2/5.$
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
#!22)!'%42!6%,
37).'/6%2"%$
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
#!22)!'%&%%$3).4/
/.&,!4,%6%,'2/5.$
,%!$3#2%7840)
37).'/6%2#2/333,)$%
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
-!8)-5-4//,3):%8
$)34!.#%"%47%%.#%.4%23
(%!$34/#+/24!),34/#+
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
7%)'(4,"3
30).$,%"/2%
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
30).$,%4!0%2-4
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
30).$,%4(2%!$840)
(!)2!.$"544/.!,,,/.'3,%%6%3()243
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
4!),34/#+4!0%2-4
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
4!),34/#+42!6%,
$/./4%80/3%4/2!)./2$!-0.%33
#/-0/5.$42!6%,
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
7(%.4)2%$
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
"%&/2%34!24).'-/4/2
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
/.&,!4,%6%,'2/5.$
$!-!'%7),,/##52)&
0%23/.!,).*529
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
#!22)!'%&%%$3).4/
$!-!'%7),,/##52)&
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
#!22)!'%42!6%,
37).'/6%2"%$
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
%.4!.',%-%.4
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
,%!$3#2%7840)
(%!$34/#+/24!),34/#+
37).'/6%2#2/333,)$%
#!22)!'%&%%$3).4/
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
-!8)-5-4//,3):%8
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
$)34!.#%"%47%%.#%.4%23
(!:!2$
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
2%!$AND5.$%234!.$
(%!$34/#+/24!),34/#+
7%)'(4,"3
30).$,%"/2%
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
4IEBACKLONGHAIRROLLUP
INSTRUCTIONMANUALTO
(!)2!.$"544/.!,,,/.'3,%%6%3()243
30).$,%4!0%2-4
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
LONGSLEEVESANDREMOVE
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
AVOIDSERIOUSINJURY)FA
30).$,%4(2%!$840)
$/./4%80/3%4/2!)./2$!-0.%33
4!),34/#+4!0%2-4
LOOSECLOTHINGJEWELRYOR
MANUALISNOTAVAILABLE
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
4!),34/#+42!6%,
GLOVESTOPREVENTGETTING
$/./4USEMACHINE'O
7(%.4)2%$
#/-0/5.$42!6%,
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
CAUGHTINMOVINGPARTS
TOWWWGRIZZLYCOMOR
"%&/2%34!24).'-/4/2
CALL
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
/.&,!4,%6%,'2/5.$
#!22)!'%42!6%,
$!-!'%7),,/##52)&
37).'/6%2"%$
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
,%!$3#2%7840)
37).'/6%2#2/333,)$%
#!22)!'%&%%$3).4/
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
0%23/.!,).*529
-!8)-5-4//,3):%8
$)34!.#%"%47%%.#%.4%23
2%!$AND5.$%234!.$
%.4!.',%-%.4
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
(%!$34/#+/24!),34/#+
7%)'(4,"3
30).$,%"/2%
INSTRUCTIONMANUALTO
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
(!:!2$ 30).$,%4!0%2-4
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
%.4!.',%-%.4
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
AVOIDSERIOUSINJURY)FA
30).$,%4(2%!$840)
4IEBACKLONGHAIRROLLUP
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
(!:!2$
4!),34/#+4!0%2-4
MANUALISNOTAVAILABLE
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
LONGSLEEVESANDREMOVE
4!),34/#+42!6%,
4IEBACKLONGHAIRROLLUP
(!)2!.$"544/.!,,,/.'3,%%6%3()243
$/./4USEMACHINE'O
LOOSECLOTHINGJEWELRYOR
#/-0/5.$42!6%,
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
LONGSLEEVESANDREMOVE
TOWWWGRIZZLYCOMOR
GLOVESTOPREVENTGETTING
$/./4%80/3%4/2!)./2$!-0.%33
LOOSECLOTHINGJEWELRYOR
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
CAUGHTINMOVINGPARTS
CALL
7(%.4)2%$
GLOVESTOPREVENTGETTING
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
CAUGHTINMOVINGPARTS
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
"%&/2%34!24).'-/4/2
$!-!'%7),,/##52)&
0%23/.!,).*529
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
#!22)!'%&%%$3).4/
/.&,!4,%6%,'2/5.$
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
(%!$34/#+/24!),34/#+
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
%.4!.',%-%.4
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
(!:!2$
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
(!)2!.$"544/.!,,,/.'3,%%6%3()243
4IEBACKLONGHAIRROLLUP
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
LONGSLEEVESANDREMOVE
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
$/./4%80/3%4/2!)./2$!-0.%33
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
LOOSECLOTHINGJEWELRYOR
7(%.4)2%$
GLOVESTOPREVENTGETTING
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
"%&/2%34!24).'-/4/2
CAUGHTINMOVINGPARTS
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
/.&,!4,%6%,'2/5.$
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
$!-!'%7),,/##52)&
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
%.4!.',%-%.4
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
#!22)!'%&%%$3).4/
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
(!:!2$
(%!$34/#+/24!),34/#+
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
4IEBACKLONGHAIRROLLUP
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
./4)#%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
7!2.).'
-/$%,'8 ,!4(%
7!2.).'
7!2.).'
G0602 Labels & Cosmetic
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
./4)#%
947 ./4)#%
./4)#%
./4)#%
-/$%,'8 ,!4(%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
-/$%,'8,!4(%
7!2.).'
./4)#%
./4)#%
7!2.).'
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
$/./4#(!.'%"%47%%.
3%26)#%
./4)#%
()'(,/77(),%25..).'
./4)#%
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
$/./4#(!.'%"%47%%.
./4)#%
()'(,/77(),%25..).'
7!2.).'
7!2.).'
./4)#%
7!2.).'
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
(!)2!.$"544/.!,,,/.'3,%%6%3()243
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
$/./4%80/3%4/2!)./2$!-0.%33
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
7(%.4)2%$
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
"%&/2%34!24).'-/4/2
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
/.&,!4,%6%,'2/5.$
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
-/$%,'8 ,!4(%
-/4/2(063).',%0(!3%
37).'/6%2"%$
37).'/6%2#2/333,)$%
$)34!.#%"%47%%.#%.4%23
30).$,%"/2%
30).$,%4!0%2-4
30).$,%4(2%!$840)
4!),34/#+4!0%2-4
4!),34/#+42!6%,
2%!$AND5.$%234!.$
#/-0/5.$42!6%,
./4)#%
-/$%,'8 ,!4(%
./4)#%
$!-!'%7),,/##52)&
#!22)!'%&%%$3).4/
(%!$34/#+/24!),34/#+
./4)#%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
7!2.).'
2%!$AND5.$%234!.$
INSTRUCTIONMANUALTO
AVOIDSERIOUSINJURY)FA
MANUALISNOTAVAILABLE
$/./4USEMACHINE'O
TOWWWGRIZZLYCOMOR
CALL
$/./4%80/3%4/2!)./2$!-0.%33
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
7(%.4)2%$
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
"%&/2%34!24).'-/4/2
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
/.&,!4,%6%,'2/5.$
CHECK OIL
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
LEVELS BEFORE USING!
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
REFER TO
OWNER’S MANUAL
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
FOR OIL TYPE AND
AMOUNT.
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
940
-/4/2(063).',%0(!3%
37).'/6%2"%$
37).'/6%2#2/333,)$%
$)34!.#%"%47%%.#%.4%23
30).$,%"/2%
30).$,%4!0%2-4
30).$,%4(2%!$840)
4!),34/#+4!0%2-4
4!),34/#+42!6%,
#/-0/5.$42!6%,
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
-/$%,'8 ,!4(%
$!-!'%7),,/##52)&
#!22)!'%&%%$3).4/
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
(%!$34/#+/24!),34/#+37).'/6%2"%$
#!22)!'%42!6%,
,%!$3#2%7840)
37).'/6%2#2/333,)$%
%.4!.',%-%.4
$)3#/..%#4
-!8)-5-4//,3):%8
$)34!.#%"%47%%.#%.4%23
(!:!2$
7%)'(4,"3
30).$,%"/2%
0/7%2"%&/2%
4IEBACKLONGHAIRROLLUP
30).$,%4!0%2-4
#2/333,)$%42!6%,
-/4/2(063).',%0(!3%
LONGSLEEVESANDREMOVE
!$*534-%.43
30).$,%4(2%!$840)
#!22)!'%42!6%,
37).'/6%2"%$
4!),34/#+4!0%2-4
,%!$3#2%7840)
37).'/6%2#2/333,)$%
LOOSECLOTHINGJEWELRYOR
-!).4%.!.#%/2
4!),34/#+42!6%,
-!8)-5-4//,3):%8
$)34!.#%"%47%%.#%.4%23
2%!$AND5.$%234!.$
GLOVESTOPREVENTGETTING
$/./4#(!.'%"%47%%.
7%)'(4,"3
30).$,%"/2%
3%26)#% #/-0/5.$42!6%,
CAUGHTINMOVINGPARTS
INSTRUCTIONMANUALTO
30).$,%4!0%2-4
()'(,/77(),%25..).'
AVOIDSERIOUSINJURY)FA
30).$,%4(2%!$840)
4!),34/#+4!0%2-4
MANUALISNOTAVAILABLE
4!),34/#+42!6%,
&!),52% 4/ &/,,/7
4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
%.4!.',%-%.4
$/./4USEMACHINE'O
$)3#/..%#4
#/-0/5.$42!6%,
0%23/.!,).*529
(!:!2$
TOWWWGRIZZLYCOMOR 2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
0/7%2"%&/2%
4IEBACKLONGHAIRROLLUP
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
CALL
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
LONGSLEEVESANDREMOVE
!$*534-%.43
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
LOOSECLOTHINGJEWELRYOR
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
-!).4%.!.#%/2
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
0%23/.!,).*529
GLOVESTOPREVENTGETTING
(!)2!.$"544/.!,,,/.'3,%%6%3()243
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
3%26)#%
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
CAUGHTINMOVINGPARTS
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
-/$%,'8,!4(%
949
7!2.).'
LONGSLEEVESANDREMOVE
LOOSECLOTHINGJEWELRYOR
GLOVESTOPREVENTGETTING
CAUGHTINMOVINGPARTS
./4)#%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
./4)#%
7!2.).'
941
./4)#%
66
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
7!2.).'
7!2.).'
7!2.).'
-/$%,'8 ,!4(%
./4)#%
$/./4#(!.'%"%47%%.
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
()'(,/77(),%25..).'
855
7!2.).'
2%!$AND5.$%234!.$
INSTRUCTIONMANUALTO
AVOIDSERIOUSINJURY)FA
MANUALISNOTAVAILABLE
$/./4USEMACHINE'O
TOWWWGRIZZLYCOMOR
CALL
$!-!'%7),,/##52)&
#!22)!'%&%%$3).4/
(%!$34/#+/24!),34/#+
#2/333,)$%42!6%,
#!22)!'%42!6%,
,%!$3#2%7840)
-!8)-5-4//,3):%8
7%)'(4,"3
#2/333,)$%42!6%,
#!22)!'%42!6%,
,%!$3#2%7840)
-!8)-5-4//,3):%8
7%)'(4,"3
7!2.).'
2%!$AND5.$%234!.$
INSTRUCTIONMANUALTO
AVOIDSERIOUSINJURY)FA
MANUALISNOTAVAILABLE
$/./4USEMACHINE'O
TOWWWGRIZZLYCOMOR
CALL
7!2.).'
INSTRUCTIONMANUALTO
AVOIDSERIOUSINJURY)FA
MANUALISNOTAVAILABLE
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
$/./4USEMACHINE'O
./4)#%
NOTICE
0%23/.!,).*529
$/./4#(!.'%"%47%%.
TOWWWGRIZZLYCOMOR 2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
CALL
()'(,/77(),%25..).'
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
DAMAGE WILL OCCUR IF
CARRIAGE FEEDS INTO
HEADSTOCK OR TAILSTOCK!
7!2.).'
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
(!)2!.$"544/.!,,,/.'3,%%6%3()243
%.4!.',%-%.4
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
(!:!2$
$/./4%80/3%4/2!)./2$!-0.%33
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
4IEBACKLONGHAIRROLLUP
7(%.4)2%$
LONGSLEEVESANDREMOVE
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
LOOSECLOTHINGJEWELRYOR
"%&/2%34!24).'-/4/2
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
GLOVESTOPREVENTGETTING
/.&,!4,%6%,'2/5.$
CAUGHTINMOVINGPARTS
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
&!),52% 4/ &/,,/7 4(%3% 7!2.).'3 7),, 2%35,4 ). 3%2)/53
0%23/.!,).*529
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
2%!$!.$5.$%234!.$-!.5!,"%&/2%34!24).'-!#().%
!,7!937%!2!.3)!002/6%$3!&%49',!33%3
0,5'0/7%2#/2$).4/'2/5.$%$/54,%4/.,9
+%%0'5!2$3!.$%9%3()%,$3).0,!#%$52).'!,,/0%2!4)/.3
$/./47%!2,//3%#,/4().'',/6%3/2*%7%,293%#52%,/.'
(!)2!.$"544/.!,,,/.'3,%%6%3()243
%.4!.',%-%.4
$)3#/..%#40/7%202)/24/3%26)#).'3%44).'50/2!$*534).'
(!:!2$
$/./4%80/3%4/2!)./2$!-0.%33
$/./4/0%2!4%5.$%24(%).&,5%.#%/&$25'3/2!,#/(/,/2
4IEBACKLONGHAIRROLLUP
7(%.4)2%$
LONGSLEEVESANDREMOVE
-!+%352%-!#().%)302/0%2,9!$*534%$!.$3%450#/22%#4,9
"%&/2%34!24).'-/4/2
LOOSECLOTHINGJEWELRYOR
"%&/2%34!24).'-!#().%-!+%#%24!).-!#().%2%3433%#52%,9
GLOVESTOPREVENTGETTING
/.&,!4,%6%,'2/5.$
CAUGHTINMOVINGPARTS
$/./4,%!6%!#(5#++%9).$2),,#(5#+/2,!4(%#(5#+
$/./42%6%23%-/4/2$)2%#4)/.7(),%,!4(%)3)./0%2!4)/.
$/./4,%!6%-!#().%5.!44%.$%$7(),%)4)325..).'
$/./4/0%2!4%-!#().%7)4($2)6%#/6%22%-/6%$
$/./434/0,!4(%/2-),,30).$,%7)4(9/52(!.$
!,7!935.0,5'-!#().%7(%.#(!.').''%!23"%,43
7!2.).'
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
CHECK OIL
LEVELS BEFORE USING!
./4)#%
$!-!'%7),,/##52)&
#!22)!'%&%%$3).4/
(%!$34/#+/24!),34/#+
REFER TO
OWNER’S MANUAL
FOR OIL TYPE AND
AMOUNT.
./4)#%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
./4)#%
$/./4#(!.'%"%47%%.
()'(,/77(),%25..).'
7!2.).'
%.4!.',%-%.4
(!:!2$
4IEBACKLONGHAIRROLLUP
LONGSLEEVESANDREMOVE
LOOSECLOTHINGJEWELRYOR
GLOVESTOPREVENTGETTING
CAUGHTINMOVINGPARTS
950
./4)#%
$!-!'%7),,/##52)&
#!22)!'%&%%$3).4/
(%!$34/#+/24!),34/#+
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
946
951
NOTICE
DAMAGE WILL OCCUR IF
CARRIAGE FEEDS INTO
HEADSTOCK OR TAILSTOCK!
7!2.).'
%.4!.',%-%.4
(!:!2$
4IEBACKLONGHAIRROLLUP
LONGSLEEVESANDREMOVE
LOOSECLOTHINGJEWELRYOR
GLOVESTOPREVENTGETTING
CAUGHTINMOVINGPARTS
$)3#/..%#4
0/7%2"%&/2%
!$*534-%.43
-!).4%.!.#%/2
3%26)#%
948
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
66
855
940
941
946
SAFETY GLASSES LABEL ALUMINUM
READ MANUAL LABEL ALUMINUM
MACHINE ID LABEL ALUMINUM
ENTANGLEMENT LABEL ALUMINUM
SHIFT NOTICE LABEL ALUMINUM
947
948
949
950
951
DISCONNECT POWER LABEL ALUM
CARRIAGE FEED DAMAGE LABEL ALUM
GRIZZLY TOUCH-UP PAINT
PUTTY TOUCH-UP PAINT
STOP OIL FILL TAG
P0602066
P0602855
P0602940
P0602941
P0602946
Model G0602/G0752 (Mfd. Since 03/17)
P0602947
P0602948
PPAINT-1
PPAINT-11
P0602951
-87-
G0752 Machine Labels B
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
G0752 Machine Labels B
(11/06/12)
Manufactured for Grizzly in China
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACES
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
3PINDLE4YPE4HREADED40)
3WING/VER"ED
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIEC
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
3PINDLE4APER-4
$ISTANCE"ETWEEN#ENTERS
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSE
MODEL G0752
6!2)!",%30%%$,!4(%
Note: Make the background color of this label
match that of the chart to the left of it.
G0752 Labels & Cosmetic
&ULL,OAD!MP$RAW!
3WING/VER"ED
$ISTANCE"ETWEEN#ENTERS
G0752
3WING/VER#ROSS3LIDE
#OMPOUND4RAVEL
#ROSS3LIDE4RAVEL
3PINDLE4YPE4HREADED40)
3PINDLE4APER-4
G0752 Machine Labels B
SPINDLE SPEED
(11/06/12)
625
L100
M160
H250
L800
M1300
H2000
3PINDLE"ORE
s,ABELISACTUALSIZE
4AILSTOCK4APER-4
4AILSTOCK1UILL4RAVEL
s,ABELMUSTBEMADEOF
G0752
Machine Labels B
7EIGHTLBS
$ATE
Change spindle direction
ONLY when spindle rotation
is stopped.
&ULL,OAD!MP$RAW!
3WING/VER"ED
G0752
3PECIFICATIONS
G0752 Machine Labels B
(11/06/12)
950
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
OILRESISTANTMATERIAL
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
OILRESISTANTMATERIAL
MODEL G0752
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
artwork changes are required, contact us immediately at manuals@grizzly.com.
(11/06/12)
E ME R
3PECIFICATIONS
OP
ST
G0752 Machine Labels A
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
oil-resistant material
(11/06/12)
3PECIFICATIONS
3PECIFICATIONS
30).$,%30%%$
G0752 Machine Labels B
READ and UNDERSTAND
instruction manual to
avoid serious injury. If a
manual is not available,
DO NOT use machine. Go
to www.grizzly.com or
call (800) 523-4777.
WORKPIECEMATERIAL
3PINDLE"ORE
GLOVESORJEWELRY
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESE
3WING/VER#ROSS3LIDE
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTING
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
4AILSTOCK4APER-4
#OMPOUND4RAVEL
ADJUSTINGORSERVICING
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
4AILSTOCK1UILL4RAVEL
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDAND
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
7EIGHTLBS
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
3PINDLE4YPE4HREADED40)
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGA
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
3PINDLE4APER-4
WORKPIECEMATERIALCHECK OIL
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
3PINDLE"ORE
$ATE
LEVELS BEFORE USING!
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIE
.EVERLEAVELATHERUNNINGUNATTENDED
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLE
4AILSTOCK4APER-4
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
EXCESSIVELYTIRED
4AILSTOCK1UILL4RAVEL
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
3ERIAL.UMBER
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
7EIGHTLBS-OTOR(063INGLE0HASE 2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTAR
4OREDUCETHERISKOFSERIOUSINJURYWHENUSI
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
2EADANDUNDERSTANDENTIREMANUAL
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
&ULL,OAD!MP$RAW! 0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
Manufactured for Grizzly in China
!LWAYSWEAR!.3)APPROVEDSAFETYGLAS
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMO
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
3WING/VER"ED
$ATE
!VOIDGETTINGENTANGLEDINROTATINGSPIND
.EVERLEAVELATHERUNNINGUNATTENDED
REFER TO
%.4!.',%-%.4
)-0!#4).*529
$ISTANCE"ETWEEN#ENTERS $ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLOR
BACKLONGHAIRROLLUPSLEEVESAND$/.
OWNER’S MANUAL
(!:!2$
(!:!2$
GLOVESORJEWELRY
FOR OIL TYPE AND
EXCESSIVELYTIRED
4IEBACKLONGHAIRROLLUP
3WING/VER#ROSS3LIDE
2EMOVECHUCKKEY
$ISCONNECTPOWERBEFOREMOUNTINGWORK
3ERIAL.UMBER
AMOUNT.
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
LONGSLEEVESANDREMOVE
#OMPOUND4RAVEL
ANDALLADJUSTMENT
ADJUSTINGORSERVICING
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATE
LOOSECLOTHINGJEWELRYOR
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSE
TOOLSBEFORESTARTING 0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSE
GLOVESTOPREVENTGETTING
Manufactured for Grizzly in China
CLEARANCETHROUGHFULLROTATIONBEFOREST
CAUGHTINMOVINGPARTS
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
3PINDLE4YPE4HREADED40)
LATHE
!LWAYSUSETHEPROPERSPINDLESPEEDFOR
3PINDLE4APER-4
WORKPIECEMATERIALCHECK OIL
3PINDLE"ORE
LEVELS BEFORE USIN
7HENFIRSTSTARTINGSPINDLEROTATIONWITH
USESLOWESTSPINDLESPEEDANDSTANDTO
4AILSTOCK4APER-4
UNTILYOUVERIFYTHATWORKPIECESAFELYROT
4AILSTOCK1UILL4RAVEL
+EEPALLGUARDSANDCOVERSINPLACEDUR
7EIGHTLBS
2EMOVECHUCKKEYANDALLADJUSTMENTTO
30).$,%30%%$
$)3#/..%#4
.EVERTOUCHROTATINGCHUCKORWORKPIECE
CHECK OIL
(!:!2$
0/7%2 $/./4REVERSESPINDLEROTATIONWHILES
$ATE
LEVELS
BEFORE
U
.EVERLEAVELATHERUNNINGUNATTENDED
REFER
TO
5SINGASPINDLESPEED
%.4!.',%-%.4
)-0!#4).*529
BEFORE $ONOTOPERATEUNDERINFLUENCEOFDRUGS
OWNER’S MANUAL
(!:!2$
THATISTOOFASTFORTHE
(!:!2$
!$*534-%.43
EXCESSIVELYTIRED
FOR OIL TYPE AND
4IEBACKLONGHAIRROLLUP
CHUCKORANINSTALLED
2EMOVECHUCKKEY
3ERIAL.UMBER
#HANGECOOLANTREGULARLYANDAVOIDCON
AMOUNT.
LONGSLEEVESANDREMOVE
-!).4%.!.#%
WORKPIECECANRESULT
ANDALLADJUSTMENT
0ROPERLYSUPPORTLONGWORKPIECESWITHA
LOOSECLOTHINGJEWELRYOR
/23%26)#%
INSERIOUSIMPACT
TOOLSBEFORESTARTING 0REVENTUNAUTHORIZEDUSEBYCHILDRENOR
GLOVESTOPREVENTGETTING
Manufactured for Grizzly in China
INJURIESORDEATH5SE
RESTRICTACCESSORDISABLEMACHINEWHEN
CAUGHTINMOVINGPARTS
LATHE
REFER TO
)-0!#4).*529
SLOWSPINDLESPEEDS %.4!.',%-%.4
OWNER’S MANUA
(!:!2$
WITHLARGEORBULKY
(!:!2$
FOR OIL TYPE AN
4IEBACKLONGHAIRROLLUP
WORKPIECES.EVER
2EMOVECHUCKKEY
AMOUNT.
LONGSLEEVESANDREMOVE
0).#(%.4!.',%-%.4
EXCEED20-RATINGOF
ANDALLADJUSTMENT
LOOSECLOTHINGJEWELRYOR
(!:!2$
CHUCK
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
$ISCONNECTPOWER
CAUGHTINMOVINGPARTS
LATHE
941
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
2EADANDUNDERSTANDENTIREMANUAL
CHECK OIL
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
LEVELS BEFORE USING!
-OTOR(063INGLE0HASE
6!2)!",%30%%$,!4(%
$ISTANCE"ETWEEN#ENTERS
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
GLOVESORJEWELRY
3WING/VER#ROSS3LIDE
2EADANDUNDERSTANDENTIREMANUAL
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
&ULL,OAD!MP$RAW!
#OMPOUND4RAVEL
ADJUSTINGORSERVICING
START
STOP
REV
NC
FWD
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
GE Y
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
3WING/VER"ED
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
3PINDLE4YPE4HREADED40)
$ISTANCE"ETWEEN#ENTERS
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
REFER TO
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
%.4!.',%-%.4
)-0!#4).*529
3PINDLE4APER-4
WORKPIECEMATERIAL
OWNER’S MANUAL
(!:!2$
GLOVESORJEWELRY
(!:!2$
-OTOR(063INGLE0HASE
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
3PINDLE"ORE
3WING/VER#ROSS3LIDE
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
FOR OIL TYPE AND
4IEBACKLONGHAIRROLLUP
2EMOVECHUCKKEY
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
AMOUNT.
4AILSTOCK4APER-4
LONGSLEEVESANDREMOVE
SPINDLE SPEED 2EADANDUNDERSTANDENTIREMANUAL
&ULL,OAD!MP$RAW!
#OMPOUND4RAVEL
ANDALLADJUSTMENT
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
LOOSECLOTHINGJEWELRYOR
ADJUSTINGORSERVICING
4AILSTOCK1UILL4RAVEL
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
TOOLSBEFORESTARTING
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
GLOVESTOPREVENTGETTING
3WING/VER"ED
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
7EIGHTLBS
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
CAUGHTINMOVINGPARTS
LATHE
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
$ISTANCE"ETWEEN#ENTERS
L100
L800
3PINDLE4YPE4HREADED40)
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
M160
M1300
$ATE
GLOVESORJEWELRY
.EVERLEAVELATHERUNNINGUNATTENDED
3WING/VER#ROSS3LIDE
3PINDLE4APER-4
H250
H2000
WORKPIECEMATERIAL
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
#OMPOUND4RAVEL
EXCESSIVELYTIRED
3PINDLE"ORE
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
ADJUSTINGORSERVICING
3ERIAL.UMBER
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
#ROSS3LIDE4RAVEL
4AILSTOCK4APER-4
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
30).$,%30%%$
$)3#/..%#4
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
Manufactured for Grizzly in China
3PINDLE4YPE4HREADED40)
MOTOR
4AILSTOCK1UILL4RAVEL
(!:!2$
0/7%2 RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
5SINGASPINDLESPEED
BEFORE
3PINDLE4APER-4
7EIGHTLBS
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
THATISTOOFASTFORTHE
WORKPIECEMATERIAL
!$*534-%.43
SPINDLE CHUCKORANINSTALLED
3PINDLE"ORE
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
-!).4%.!.#%
WORKPIECECANRESULT
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
4AILSTOCK4APER-4
/23%26)#%
INSERIOUSIMPACT
$ATE
L M H
.EVERLEAVELATHERUNNINGUNATTENDED
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
INJURIESORDEATH5SE
EYE/FACE
4AILSTOCK1UILL4RAVEL
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
INJURY
HAZARD!
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
SLOWSPINDLESPEEDS
Always wear safety
CHECK OIL
7EIGHTLBS
EXCESSIVELYTIRED
glasses and face
WITHLARGEORBULKY
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
LEVELS BEFORE USING!
shield when using
Change spindle direction
3ERIAL.UMBER this machine.
WORKPIECES.EVER
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
ONLY when spindle rotation
0).#(%.4!.',%-%.4
-OTOR(063INGLE0HASE
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
EXCEED20-RATINGOF
is stopped.
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
(!:!2$
2EADANDUNDERSTANDENTIREMANUAL
CHUCK
&ULL,OAD!MP$RAW!
$ATE
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
.EVERLEAVELATHERUNNINGUNATTENDED
$ISCONNECTPOWER
START
STOP
REV
CY
FWD
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
EN
Manufactured for GrizzlyGin
China
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
3WING/VER"ED
BEFOREOPENINGTHIS
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
DOOR3TAYCLEAROF
$ISTANCE"ETWEEN#ENTERS EXCESSIVELYTIRED BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
REFER TO
%.4!.',%-%.4
)-0!#4).*529
OUTBOARDSPINDLEWHEN
3ERIAL.UMBER
OWNER’S MANUAL
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
(!:!2$
GLOVESORJEWELRY
(!:!2$
-OTOR(063INGLE0HASE
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
3WING/VER#ROSS3LIDE
LATHEISRUNNING
FOR OIL TYPE AND
4IEBACKLONGHAIRROLLUP
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
2EMOVECHUCKKEY
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
AMOUNT.
LONGSLEEVESANDREMOVE
2EADANDUNDERSTANDENTIREMANUAL
&ULL,OAD!MP$RAW! 0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
#OMPOUND4RAVEL
ANDALLADJUSTMENT
LOOSECLOTHINGJEWELRYOR
ADJUSTINGORSERVICING
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
Manufactured for Grizzly in China
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
3WING/VER"ED
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
CAUGHTINMOVINGPARTS
LATHE
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
$ISTANCE"ETWEEN#ENTERS
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
3PINDLE4YPE4HREADED40)
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
GLOVESORJEWELRY
3WING/VER#ROSS3LIDE
3PINDLE4APER-4
WORKPIECEMATERIAL
CHECK
OIL
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
#OMPOUND4RAVEL
3PINDLE"ORE
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
ADJUSTINGORSERVICING
LEVELS
BEFORE USING!
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
#ROSS3LIDE4RAVEL
4AILSTOCK4APER-4
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
30).$,%30%%$
$)3#/..%#4
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
3PINDLE4YPE4HREADED40)
4AILSTOCK1UILL4RAVEL
(!:!2$
0/7%2
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
5SINGASPINDLESPEED
BEFORE
3PINDLE4APER-4
7EIGHTLBS
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
WORKPIECEMATERIAL
CHECKTHATISTOOFASTFORTHE
OIL
!$*534-%.43
3PINDLE"ORE
CHUCKORANINSTALLED
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
LEVELS BEFORE
USING!
-!).4%.!.#%
WORKPIECECANRESULT
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
-OTOR(063INGLE0HASE
4AILSTOCK4APER-4
/23%26)#%
INSERIOUSIMPACT
$ATE
.EVERLEAVELATHERUNNINGUNATTENDED
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
REFER TO
%.4!.',%-%.4 4AILSTOCK1UILL4RAVEL
INJURIESORDEATH5SE
)-0!#4).*529 &ULL,OAD!MP$RAW!
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
SLOWSPINDLESPEEDS
OWNER’S MANUAL
(!:!2$
(!:!2$
3WING/VER"ED
7EIGHTLBS
EXCESSIVELYTIRED
WITHLARGEORBULKY
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
FOR OIL TYPE AND
4IEBACKLONGHAIRROLLUP
3ERIAL.UMBER
WORKPIECES.EVER
2EMOVECHUCKKEY
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
$ISTANCE"ETWEEN#ENTERS
AMOUNT.
LONGSLEEVESANDREMOVE
0).#(%.4!.',%-%.4
EXCEED20-RATINGOF
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
ANDALLADJUSTMENT
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
(!:!2$
LOOSECLOTHINGJEWELRYOR
3WING/VER#ROSS3LIDE
CHUCK
$ATE
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
.EVERLEAVELATHERUNNINGUNATTENDED
$ISCONNECTPOWER
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
REFER TO
%.4!.',%-%.4
Manufactured for
Grizzly in China
)-0!#4).*529
#OMPOUND4RAVEL
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
BEFOREOPENINGTHIS
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
CAUGHTINMOVINGPARTS
LATHE
OWNER’S MANUAL
(!:!2$
DOOR3TAYCLEAROF
(!:!2$
EXCESSIVELYTIRED
#ROSS3LIDE4RAVEL
FOR OIL TYPE AND
4IEBACKLONGHAIRROLLUP
OUTBOARDSPINDLEWHEN
3ERIAL.UMBER
2EMOVECHUCKKEY
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
AMOUNT.
3PINDLE4YPE4HREADED40)
LONGSLEEVESANDREMOVE
LATHEISRUNNING
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
ANDALLADJUSTMENT
LOOSECLOTHINGJEWELRYOR
3PINDLE4APER-4
TOOLSBEFORESTARTING 0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
GLOVESTOPREVENTGETTING
Manufactured for Grizzly in China
3PINDLE"ORE
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
CAUGHTINMOVINGPARTS
LATHE
-OTOR(063INGLE0HASE
E ME R
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
oil-resistant material
(11/06/12)
Always wear safety
glasses and face
shield when using
this machine.
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
6!2)!",%30%%$,!4(%
3PECIFICATIONS
Note: Make the background color of this label
EYE/FACE
INJURY HAZARD!
match that of the chart to the left of MODEL
it.
3PECIFICATIONS
G0752
OP
ST
G0752 Machine Labels A
SPINDLE
L M H
3ERIAL.UMBER
Manufactured for Grizzly in China
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
artwork changes are required, contact us immediately at manuals@grizzly.com.
(11/06/12)
MOTOR
940
OILRESISTANTMATERIAL
OILRESISTANTMATERIAL
(11/06/12)
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
MODEL G0752
OILRESISTANTMATERIAL 6!2)!",%30%%$,!4(%
MODEL G0752
G0752 Machine Labels B
READ and UNDERSTAND
instruction manual to
avoid serious injury. If a
manual is not available,
DO NOT use machine. Go
to www.grizzly.com or
call (800) 523-4777.
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
2EADANDUNDERSTANDENTIREMANUAL
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
GLOVESORJEWELRY
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
ADJUSTINGORSERVICING
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
WORKPIECEMATERIAL
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
.EVERLEAVELATHERUNNINGUNATTENDED
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
EXCESSIVELYTIRED
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
(11/06/12)
MODEL G07
6!2)!",%30%%$
3PECIFICATIONS
-OTOR(063INGLE0HASE
6!2)!",%30%%$,!4(%
$)3#/..%#4
BEFOREOPENINGTHIS
C
(!:!2$
DOOR3TAYCLEAROF
0/7%2
LEVELS
5SINGASPINDLESPEED
OUTBOARDSPINDLEWHEN
BEFORE
THATISTOOFASTFORTHE
LATHEISRUNNING !$*534-%.43
CHUCKORANINSTALLED
-!).4%.!.#%
WORKPIECECANRESULT
30).$,%30%%$
$)3#/..%#4
/23%26)#%
INSERIOUSIMPACT
(!:!2$
0/7%2
INJURIESORDEATH5SE
5SINGASPINDLESPEED
%.4!.',%-%.4
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
)-0!#4).*529
SLOWSPINDLESPEEDS
BEFORE
OWN
(!:!2$
THATISTOOFASTFORTHE
(!:!2$
FOR GRIZZLYWITHLARGEORBULKY
MACHINES
ONLY!DO
NOT REPRODUCE OR
CHANGE
THIS ARTWORKFOR
!$*534-%.43
4IEBACKLONGHAIRROLLUP
CHUCKORANINSTALLED
WORKPIECES.EVER
2EMOVECHUCKKEY
LONGSLEEVESANDREMOVE
'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
WITHOUT WRITTEN
APPROVAL!
-!).4%.!.#%
0).#(%.4!.',%-%.4
WORKPIECECANRESULT
ANDALLADJUSTMENT
EXCEED20-RATINGOF
LOOSECLOTHINGJEWELRYOR
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
/23%26)#%
(!:!2$
INSERIOUSIMPACT
TOOLSBEFORESTARTING
CHUCK
GLOVESTOPREVENTGETTING
INJURIESORDEATH5SE
$ISCONNECTPOWER
CAUGHTINMOVINGPARTS
LATHE
SLOWSPINDLESPEEDS
BEFOREOPENINGTHIS
WITHLARGEORBULKY
DOOR3TAYCLEAROF
WORKPIECES.EVER
OUTBOARDSPINDLEWHEN
0).#(%.4!.',%-%.4
EXCEED20-RATINGOF
LATHEISRUNNING
(!:!2$
CHUCK
951
MODEL G0752
6!2)!",%30%%$,!4(%
G0752 Machine Labels B
(11/06/12)
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
OILRESISTANTMATERIAL
3PECIFICATIONS
G0752 Machine Labels B
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
OILRESISTANTMATERIAL
(11/06/12)
949
30).$,%30%%$
(!:!2$
MODEL G0752
6!2)!",%30%%$,!4(%
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
2EADANDUNDERSTANDENTIREMANUAL
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
GLOVESORJEWELRY
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
ADJUSTINGORSERVICING
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
WORKPIECEMATERIAL
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
4AILSTOCK4APER-4
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE
OR CHANGE THIS ARTWORK
30).$,%30%%$
4AILSTOCK1UILL4RAVEL
$)3#/..%#4
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
CHECK
OIL
'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
WITHOUT WRITTEN
APPROVAL!
(!:!2$
7EIGHTLBS
0/7%2
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
LEVELS
BEFORE USING!
5SINGASPINDLESPEED
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
BEFORE
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
THATISTOOFASTFORTHE
!$*534-%.43
$ATE
.EVERLEAVELATHERUNNINGUNATTENDED
CHUCKORANINSTALLED
30).$,%30%%$
$)3#/..%#4
-!).4%.!.#%
$ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
CHECK OIL
WORKPIECECANRESULT
(!:!2$
EXCESSIVELYTIRED
0/7%2
/23%26)#%
LEVELS BEFORE USING!
INSERIOUSIMPACT
3ERIAL.UMBER
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
5SINGASPINDLESPEED
-OTOR(063INGLE0HASE
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHINE
BEFORE
INJURIESORDEATH5SE
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
THATISTOOFASTFORTHE
REFER TO
2EADANDUNDERSTANDENTIREMANUAL
)-0!#4).*529
&ULL,OAD!MP$RAW!
SLOWSPINDLESPEEDS %.4!.',%-%.4
!$*534-%.43
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
OWNER’S MANUAL
!LWAYSWEAR!.3)APPROVEDSAFETYGLASSES!.$FACESHIELD
CHUCKORANINSTALLED (!:!2$
Manufactured for3WING/VER"ED
Grizzly in China
(!:!2$
WITHLARGEORBULKY4IEBACKLONGHAIRROLLUP
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
-!).4%.!.#%
FOR
OIL
TYPE
AND
!VOIDGETTINGENTANGLEDINROTATINGSPINDLEORWORKPIECEˆTIE
WORKPIECECANRESULT
2EMOVECHUCKKEY
WORKPIECES.EVER LONGSLEEVESANDREMOVE
$ISTANCE"ETWEEN#ENTERS
AMOUNT.
BACKLONGHAIRROLLUPSLEEVESAND$/./4WEARLOOSECLOTHING
/23%26)#%
INSERIOUSIMPACT
0).#(%.4!.',%-%.4
ANDALLADJUSTMENT
EXCEED20-RATINGOF
LOOSECLOTHINGJEWELRYOR
GLOVESORJEWELRY
3WING/VER#ROSS3LIDE
INJURIESORDEATH5SE
(!:!2$
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
$ISCONNECTPOWERBEFOREMOUNTINGWORKPIECESETTINGUP
CHUCK
REFER TO
%.4!.',%-%.4
)-0!#4).*529
#OMPOUND4RAVEL
SLOWSPINDLESPEEDS
CAUGHTINMOVINGPARTS
LATHE
$ISCONNECTPOWER
ADJUSTINGORSERVICING
OWNER’S MANUAL
(!:!2$
(!:!2$
WITHLARGEORBULKY4IEBACKLONGHAIRROLLUP
#ROSS3LIDE4RAVEL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHASSAFE
FOR
OIL
TYPE
AND
BEFOREOPENINGTHIS
2EMOVECHUCKKEY
WORKPIECES.EVER LONGSLEEVESANDREMOVE
CLEARANCETHROUGHFULLROTATIONBEFORESTARTINGLATHE
AMOUNT.
3PINDLE4YPE4HREADED40)
DOOR3TAYCLEAROF
0).#(%.4!.',%-%.4
ANDALLADJUSTMENT
!LWAYSUSETHEPROPERSPINDLESPEEDFORCHUCKRATINGAND
LOOSECLOTHINGJEWELRYOR
EXCEED20-RATINGOF
3PINDLE4APER-4
OUTBOARDSPINDLEWHEN
(!:!2$
WORKPIECEMATERIALCHECK OIL
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
CHUCK
3PINDLE"ORE
LATHEISRUNNING
7HENFIRSTSTARTINGSPINDLEROTATIONWITHANEWWORKPIECESETUP
CAUGHTINMOVINGPARTS
LATHE
$ISCONNECTPOWER
LEVELS BEFORE USING!
USESLOWESTSPINDLESPEEDANDSTANDTOSIDEOFSPINDLEAREA
4AILSTOCK4APER-4
BEFOREOPENINGTHIS
UNTILYOUVERIFYTHATWORKPIECESAFELYROTATES
30).$,%30%%$
4AILSTOCK1UILL4RAVEL
DOOR3TAYCLEAROF $)3#/..%#4
+EEPALLGUARDSANDCOVERSINPLACEDURINGOPERATION
(!:!2$
7EIGHTLBS
0/7%2
OUTBOARDSPINDLEWHEN
2EMOVECHUCKKEYANDALLADJUSTMENTTOOLSBEFORESTARTING
5SINGASPINDLESPEED
.EVERTOUCHROTATINGCHUCKORWORKPIECEWITHHANDS
LATHEISRUNNING BEFORE
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
$/./4REVERSESPINDLEROTATIONWHILESPINDLEISINMOTION
THATISTOOFASTFORTHE
!$*534-%.43
$ATE
FOR GRIZZLY MACHINES
ONLY!DO NOT REPRODUCE OR CHANGE
THIS ARTWORK
.EVERLEAVELATHERUNNINGUNATTENDED
CHUCKORANINSTALLED
30).$,%30%%$
REFER TO
%.4!.',%-%.4
)-0!#4).*529 $ONOTOPERATEUNDERINFLUENCEOFDRUGSORALCOHOLORWHEN
$)3#/..%#4
-!).4%.!.#%
WITHOUT WRITTENWORKPIECECANRESULT
APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
OWNER’S MANUAL
(!:!2$
(!:!2$
EXCESSIVELYTIRED
0/7%2
(!:!2$
/23%26)#%
FOR OIL TYPE AND
INSERIOUSIMPACT
4IEBACKLONGHAIRROLLUP
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
3ERIAL.UMBER
#HANGECOOLANTREGULARLYANDAVOIDCONTACTWITHSKIN
5SINGASPINDLESPEED
2EMOVECHUCKKEY
BEFORE
AMOUNT.
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
LONGSLEEVESANDREMOVE
INJURIESORDEATH5SE
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
THATISTOOFASTFORTHE
ANDALLADJUSTMENT
LOOSECLOTHINGJEWELRYOR
SLOWSPINDLESPEEDS
!$*534-%.43
FOR GRIZZLY MACHINES
ONLY!DO NOT REPRODUCE OR CHANGE
THIS ARTWORK
0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
CHUCKORANINSTALLED
TOOLSBEFORESTARTING
GLOVESTOPREVENTGETTING
Manufactured
for Grizzly in China
WITHLARGEORBULKY
RESTRICTACCESSORDISABLEMACHINEWHENUNATTENDED
-!).4%.!.#%
WITHOUT WRITTEN
APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
CAUGHTINMOVINGPARTS
WORKPIECECANRESULT
LATHE
$ISCONNECTPOWER
$)3#/..%#4
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
0/7%2
5SINGASPINDLESPEED
OUTBOARDSPINDLEWHEN
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
BEFORE
THATISTOOFASTFORTHE
LATHEISRUNNING
FOR GRIZZLY MACHINES
ONLY!DO NOT REPRODUCE
OR CHANGE
THIS ART
!$*534-%.43
CHUCKORANINSTALLED
WITHOUT WRITTEN
APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAP
-!).4%.!.#%
WORKPIECECANRESULT
/23%26)#%
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.co
INSERIOUSIMPACT
INJURIESORDEATH5SE
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
SLOWSPINDLESPEEDS
FOR GRIZZLYWITHLARGEORBULKY
MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS A
WORKPIECES.EVER
WITHOUT WRITTEN
APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOU
0).#(%.4!.',%-%.4
EXCEED20-RATINGOF
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly
(!:!2$
CHUCK
MODEL G0752
6!2)!",%30%%$,!4(%
3PECIFICATIONS
CHECK OIL
LEVELS BEFORE USING!
$ISCONNECTPOWER
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
OUTBOARDSPINDLEWHEN
LATHEISRUNNING
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHAN
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANG
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanua
REFER TO
OWNER’S MANUAL
FOR OIL TYPE AND
AMOUNT.
946
WORKPIECES.EVER
/23%26)#%
INSERIOUSIMPACT
0).#(%.4!.',%-%.4
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
EXCEED20-RATINGOF
INJURIESORDEATH5SE
CHUCK
SLOWSPINDLESPEEDS
WITHLARGEORBULKY
WORKPIECES.EVER
EXCEED20-RATINGOF
CHUCK
(!:!2$
$ISCONNECTPOWER
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
0).#(%.4!.',%-%.4
OUTBOARDSPINDLEWHEN
(!:!2$
LATHEISRUNNING
$ISCONNECTPOWER
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
OUTBOARDSPINDLEWHEN
LATHEISRUNNING
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
30).$,%30%%$
(!:!2$
947
5SINGASPINDLESPEED
THATISTOOFASTFORTHE
CHUCKORANINSTALLED
WORKPIECECANRESULT
INSERIOUSIMPACT
CHECK
OIL
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
INJURIESORDEATH5SE
LEVELS BEFORE
USING!%.4!.',%-%.4
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
SLOWSPINDLESPEEDS
(!:!2$
WITHLARGEORBULKY4IEBACKLONGHAIRROLLUP
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
WORKPIECES.EVERLONGSLEEVESANDREMOVE
LOOSECLOTHINGJEWELRYOR
EXCEED20-RATINGOF
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
GLOVESTOPREVENTGETTING
CHUCK
948
WITHOUT WRITTEN APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
952
CAUGHTINMOVINGPARTS
$)3#/..%#4
0/7%2
BEFORE
!$*534-%.43
-!).4%.!.#%
/23%26)#%
)-0!#4).*529
(!:!2$
2EMOVECHUCKKEY
0).#(%.4!.',%-%.4
ANDALLADJUSTMENT
TOOLSBEFORESTARTING
(!:!2$
LATHE
$ISCONNECTPOWER
CHECK OIL
LEVELS BEFORE USING!
REFER TO
OWNER’S MANUAL
FOR OIL TYPE AND
AMOUNT.
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
OUTBOARDSPINDLEWHEN
LATHEISRUNNING
REFER TO
OWNER’S MANUAL
FOR OIL TYPE AND
AMOUNT.
30).$,%30%%$
$)3#/..%#4
(!:!2$
0/7%2
5SINGASPINDLESPEED
BEFORE
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
THATISTOOFASTFORTHE
!$*534-%.43
FOR GRIZZLY MACHINES
ONLY!DO
NOT
REPRODUCE
OR
CHANGE
THIS ARTWORK
CHUCKORANINSTALLED
-!).4%.!.#%
WITHOUT WRITTENWORKPIECECANRESULT
APPROVAL! 'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
/23%26)#%
INSERIOUSIMPACT
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
REF PART #
625
940
941
946
947
-88-
P0752625
P0752940
PLABEL-55A
PLABEL-62C
P0752947
DESCRIPTION
s
s
#OMPOUND4RAVEL
-OTOR(063INGLE0HASE
4OREDUCETHERISKOFSERIOUSINJURYWHENUSINGTHISMACHIN
ADJUSTINGORSERVICING
0ROPERLYSUPPORTLONGWORKPIECESWITHANAPPROPRIATEREST
#ROSS3LIDE4RAVEL
2EADANDUNDERSTANDENTIREMANUAL
-AKESUREWORKPIECEISPROPERLYANDSECURELYHELDANDHAS
&ULL,OAD!MP$RAW! 0REVENTUNAUTHORIZEDUSEBYCHILDRENORUNTRAINEDUSERS
s,ABELISACTUALSIZE
s,ABELMUSTBEMADEOF
OILRESISTANTMATERIAL
INJURIESORDEATH5SE
SLOWSPINDLESPEEDS
WITHLARGEORBULKY
WORKPIECES.EVER
EXCEED20-RATINGOF
CHUCK
REF PART #
0).#(%.4!.',%-%.4
(!:!2$
DESCRIPTION
$ISCONNECTPOWER
BEFOREOPENINGTHIS
DOOR3TAYCLEAROF
OUTBOARDSPINDLEWHEN
LATHEISRUNNING
G0752 CONTROL PANEL
948
P0752948
IMPACT INJURY HAZARD LABEL
MACHINE ID LABEL
949
P0752949
SPINDLE SPEED HAZARD LABEL
ENTANGLEMENT LABEL
950
PPAINT-11
PUTTY TOUCH-UP PAINT
8DENG><=I<G>OOAN>C9JHIG>6A!>C8#
FOR GRIZZLY MACHINES ONLY!DO NOT REPRODUCE OR CHANGE THIS ARTWORK
'RIZZLYWILLNOTACCEPTLABELSCHANGEDWITHOUTAPPROVAL)F
WRITTEN APPROVAL!
DISCONNECT POWER LABELWITHOUT
951
PPAINT-1
GRIZZLY GREEN TOUCH-UP PAINT
ARTWORKCHANGESAREREQUIREDCONTACTUSIMMEDIATELYATmanuals@grizzly.com
ENTANTANGLEMENT-GEARS LABEL
952
P0752952
STOP OIL FILL TAG
Model G0602/G0752 (Mfd. Since 03/17)
machine
SECTION 10: APPENDIX
G0602 Charts
Model G0602/G0752 (Mfd. Since 03/17)
-89-
G0752 Charts
WARRANTY CARD
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________ Email _________________________________________________
Model # ____________________ Order # _______________________ Serial # __________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1.
CUT ALONG DOTTED LINE
2.
How did you learn about us?
____ Advertisement
____ Card Deck
4.
5.
6.
____ Catalog
____ Other:
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
3.
____ Friend
____ Website
Cabinetmaker & FDM
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Old House Journal
Popular Mechanics
____
____
____
____
____
____
____
____
____
____
Popular Science
Popular Woodworking
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
Today’s Homeowner
Wood
____
____
____
____
____
____
____
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $50,000-$59,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
What is your age group?
____ 20-29
____ 50-59
____ 40-49
____ 70+
____ 30-39
____ 60-69
How long have you been a woodworker/metalworker?
____ 0-2 Years
____ 2-8 Years
____ 8-20 Years
____ 20+ Years
How many of your machines or tools are Grizzly?
____ 0-2
____ 3-5
____ 6-9
____ 10+
7.
Do you think your machine represents a good value?
_____ Yes
_____No
8.
Would you recommend Grizzly Industrial to a friend?
_____ Yes
_____No
9.
Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times.
_____ Yes
_____No
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
WARRANTY AND RETURNS
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download PDF

advertising