Version 1.4 - Anolis Lighting

Version 1.4
ArcSource Outdoor 16 MC Integral
Table of contents
1. Safety instructions ......................................................................................................................................................3
2. Fixture exterior view ................................................................................................................................................... 5
3. Installation .................................................................................................................................................................. 5
3.1 Mounting the fixture ............................................................................................................................................ 5
3.2 Top hat (Half top hat ) installation ....................................................................................................................... 6
3.3 Connection to the mains ...................................................................................................................................... 7
4. Wireless DMX operation ...........................................................................................................................................10
5. ArcSource Outdoor 16 MC Integral (RGBW) - DMX protocol ...................................................................................11
6. ArcSource Outdoor 16 MC Integral (RGBA) - DMX protocol ....................................................................................13
7. ArcSource Outdoor 24 MC Integral (SmartWhite) - DMX protocol ..........................................................................15
8. ArcSource Outdoor 24 MC Integral (Single colour) - DMX protocol.........................................................................16
9. Control menu map ....................................................................................................................................................17
10. Fixture menu...........................................................................................................................................................23
10.1 Fixture Address .................................................................................................................................................23
10.2 Fixture information ...........................................................................................................................................23
10.3 Personality ........................................................................................................................................................24
10.4 Manual mode....................................................................................................................................................25
10. 5 Test sequences.................................................................................................................................................25
10.6 Stand-alone setting...........................................................................................................................................25
10.7 Special functions ...............................................................................................................................................26
11. RDM ........................................................................................................................................................................29
12. Technical specifications ..........................................................................................................................................30
13. Cleaning and maintenance .....................................................................................................................................33
2
ArcSource Outdoor 16 MC Integral
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ArcSource Outdoor 16 MC Integral !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in
this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the fixture.
This fixture should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before cleaning, removing or installing the fuses, or any part.
Do not overload wall outlets and extension cords as this can result in fire or electric shock.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power cord
from time to time.
Do not install the unit near naked flames.
During the operation the housing becomes hot (up to 80°C)
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to a mains socket outlet with
a protective earthing connection.
Do not connect this fixture to a dimmer pack.
LED light emission. Risk of eye injury.
Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.
Keep compustible materials at least 20 cm away from the fixture.
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until it has
reached room temperature.
Avoid brute force when installing or operating the fixture.
3
ArcSource Outdoor 16 MC Integral
The fixture was designed for outdoor use. This fixture must not be used for underwater installation.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.
Avoid using the unit in locations subject to possible impacts.
The fixture body never must be covered with cloth or other materials.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
Do not block the front objective LEDs with any object when the fixture is under operation.
The fixture becomes very hot during operation. Allow the fixture to cool approximately 30 minutes prior to
manipulate with it.
Operate the fixture only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the fixture. Most damages are the result of unprofessional operation!
Do not attempt to dismantle or modify the unit.
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
Please use the original packaging if the fixture is to be transported.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock etc.
4
ArcSource Outdoor 16 MC Integral
2. Fixture exterior view
1. LED unit
2. Control unit
3. Antenna (only wireless DMX version)
4. Tilt adjusting locks
5. „U“ bracket
6. Control board with anti-vandal cover
7. Power/Data cable
8. LED unit connecting cable
3. Installation
3.1 Mounting the fixture
The ArcSource Outdoor 16 MC Integral can be arranged in any position orientation.
The LED module can be tilted to desired position by means of the tilt lock. Use an Allen key 6 to adjust desired
position (0-90°).
Three slots in the fixture “U” holder serve for mounting on the non-flammable flat surface
5
ArcSource Outdoor 16 MC Integral
Ensure that the structure to which you are attaching
the fixture is secure
Caution: Overhead installation requires experience. Fixtures may cause severe injuries when crashing down! If you
have doubts concerning the safety of a possible installation, do not install the device and consult installation with
an expert.
Warning for wireless DMX version!
The fixture is supplied with the cap screwed on the antenna connector. This cap provides declared IP rating of the
fixture but when the cap is removed, the enclosed antenna must be installed on the fixture to keep declared IP
rating of the fixture!
There is a possibility to install the LED unit and the control unit separately. Four holes with diameter of 5.3mm in
the control unit are intended for mounting on a flat, non-flammable surface. The length of the connection cable
between the control unit and the LED unit should not exceed 20 m.
3.2 Top hat (Half top hat ) installation
Top hat
Half top hat
1. Unscrew the four socket head screws 6x10 (1) in the ArcSource Outdoor 16 MC housing and slide the top
hat (2) onto ArcSource outdoor 16 MC Integral.
2. Screw the holder (3) to the top hat (2) by means of the two screws (4) with tooth washers
3. Secure the top hat on the fixture with four socket head screws 6x10 (1) .
6
ArcSource Outdoor 16 MC Integral
3.3 Connection to the mains
Fixtures must be installed by a qualified electrician in accordance with all national
and local electrical and construction codes and regulation.
This device falls under class one and must be grounded!
The ArcSource Outdoor 16 MC Integral is equiped with with a 5-cored power/data cable. The 3 cores serve for
the power supply and next 2 shielded cores are intended for DMX connection as shown the table.
Core
Connection
Core
Connection
Black
Live
Red
Data +
Blue
Neutral
White
Data -
Shielding
0
Yellow/Green
The power/data cable is connected to a junction box as shown on the picture below.
7
ArcSource Outdoor 16 MC Integral
Connect the junction box acording to the tables below
Power connection
L
N
EU
Braun
Blue
Green/yellow
US
Black
White
Green
+
0
-
Data +
Data ground(shielding)
Data -
DMX connection
Remove end caps from cable glands before passing cables into the junction box. The four cable glands M20 with
standard seals serve for cable of diameter of 6-12mm, for smaller diameter of cable (4-8mm) you have to remove
original sealing from the cable gland M20 and use the enclosed reducing seal instead it. Four reducing seals for
diameter of cable 4-8mm (P/N 13051388) are enclosed.
Fully tighten cable gland nuts and check that cables are properly fastened in the cable glands.
Note: To keep declared IP rating, every cable gland has to be covered with the end cap if this cable gland is not
used for cable passing.
Screw the cover of the junction box and check that it is fully tighten.
8
ArcSource Outdoor 16 MC Integral
The junction box allows to connect several fixtures in a daisy chain of the power/data cable. Use the 3 x 1.5mm2
power cable to connect the first junction box with the mains and the power/data cable for connecting fixtures
each other. Do not overload the supply line and the connecting leads.
The max. number (theoretical) of connected fixtures in a daisy chain depends on the input voltage:
60 fixtures at power supply= 230V (for power cable 3 x 1.5mm2)
24 fixtures at power supply= 120V (for power cable 3 x 1.5mm2)
You have to take into account the the length of the power/data cable, circuit breaker, inrush current etc. at
projecting of the fixtures installation.
9
ArcSource Outdoor 16 MC Integral
4. Wireless DMX operation
The wireless version of the ArcSource Outdoor 16 MC Integral is equipped with the Lumen Radio CRMX module
and antenna for receiving DMX signal. CRMX module operates on the 2.4 GHz band.
To link the fixture with the DMX transmitter
Select option “Wireless“ from the menu PErS (PErS-->DMX In.--> Wireless).
The fixture can be linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal (in %) is displayed in the menu item “Stat“ (Special-->Wireless-->Stat.)
To unlink the fixture from DMX transmitter.
The fixture can be unlinked from DMX transmitter via the menu item “Unlink“ (Special-->Wireless-->Unlink.)
Note: The ArcSource Outdoor 16 MC integral sends received wireless DMX signal to its wired DMX output. The
fixture behaves as a " Wireless/Wired" adaptor.
E.g. You have 5 fixtures, one fixture is equipped with the wireless DMX module and 4 fixtures are standard fixtures
without wireless DMX module. The first fixture receives wireless DMX and sents this signal to the rest of fixures,
which are connected to the first fixture by means of the DMX cable in a DMX chain.
10
ArcSource Outdoor 16 MC Integral
5. ArcSource Outdoor 16 MC Integral (RGBW) - DMX protocol
Version 1.0
Mode/Channel
1
2
3
4
-
1
1
1
-
2
2
2
-
3
3
3
-
-
4
4
-
-
-
5
1
-
-
-
-
-
6
7
Value
Function
Type of control
0 - 255
Red LEDs
Red LEDs saturation control (0-100%)
proportional
0 - 255
Green LEDs
Green LEDs saturation control (0-100%)
proportional
0 - 255
Blue LEDs
Blue LEDs saturation control (0-100%)
proportional
0 - 255
White LEDs
White LEDs saturation control (0-100%)
proportional
0
1-255
CT0
No function
Colour temperature correction (0-100%)
proportional
Virtual colour wheel
No function (for DMX mode 4)
White (R+G+B+W=full for DMX mode 1)
1-2
White 2700 K
3
White 2700 K (Halogen lamp mode)
4-5
White 3200 K
6
White 3200 K (Halogen lamp mode)
7-9
White 4200 K
10-12
White 5600 K
13-15
White 8000 K
16
Blue (Blue=full, Red+Green+White=0)
17-55
Red=0, Greenup,Blue =full, White=0
56
Light Blue (Red=0, Green=full, Blue =full, White=0)
57 - 95
Red=0, Green=full, Bluedown, White=0
96
Green (Red=0, Green=full, Blue =0, White=0)
97 – 134 Redup, Green=full, Blue=0, White=0
135
Yellow-green (Red=full, Green=full, Blue=0, White=0)
136 - 174 Red=full, Greendown, Blue=0, White=0
175
Red(Red=full, Green=0, Blue=0, White=0)
176 -214 Red=full, Green=0, Blueup, White=0
215
Magenta (Red=full, Green=0, Blue=full, White=0)
216 – 246 Reddown, Green=0, Blue=full, White=0
247
Blue (Red=0, Green=0, Blue=full, White=0)
248-251 Rainbow effect with fade time (fast slow)
252-255 Rainbow effect without fade time (fast slow)
step
step
step
step
step
step
step
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
proportional
Shutter/ Strobe
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
step
step
proportional
step
proportional
proportional
step
0
0-31
32-63
64-95
96-127
128-143
144-159
160-191
11
step
ArcSource Outdoor 16 MC Integral
2
-
-
8
-
-
-
9
192-223
224-255
Random strobe-effects from slow to fast
Shutter open
proportional
step
0 - 255
Dimmer
Dimmer intensity from 0% to 100%
proportional
0 - 255
Dimmer fine
Fine dimmer intensity from low to high
12
Proportional
ArcSource Outdoor 16 MC Integral
6. ArcSource Outdoor 16 MC Integral (RGBA) - DMX protocol
Version 1.0
Mode/Channel
1
2
3
4
-
1
1
1
-
2
2
2
-
3
3
3
-
-
4
4
-
-
-
5
1
-
-
-
-
-
6
7
Value
Function
Type of control
0 - 255
Red LEDs
Red LEDs saturation control (0-100%)
proportional
0 - 255
Green LEDs
Green LEDs saturation control (0-100%)
proportional
0 - 255
Blue LEDs
Blue LEDs saturation control (0-100%)
proportional
0 - 255
Amber LEDs
Amber LEDs saturation control (0-100%)
proportional
0
1-255
CT0
No function
Colour temperature correction (0-100%)
proportional
Virtual colour wheel
No function (for DMX mode 4)
White (R+G+B=full for DMX mode 1)
1-2
White 2700 K
3
White 2700 K (Halogen lamp mode)
4-5
White 3200 K
6
White 3200 K (Halogen lamp mode)
7-9
White 4200 K
10-12
White 5600 K
13-15
White 8000 K
16
Blue (Blue=full, Red+Green+Amber=0)
17-55
Red=0, Greenup,Blue =full, White=0
56
Light Blue (Red=0, Green=full, Blue =full, Amber =0)
57 - 95
Red=0, Green=full, Bluedown, Amber =0
96
Green (Red=0, Green=full, Blue =0, Amber =0)
97 – 134 Redup, Green=full, Blue=0, Amber =0
135
Yellow-green (Red=full, Green=full, Blue=0, Amber =0)
136 - 174 Red=full, Greendown, Blue=0, Amber =0
175
Red(Red=full, Green=0, Blue=0, Amber =0)
176 -214 Red=full, Green=0, Blueup, Amber =0
215
Magenta (Red=full, Green=0, Blue=full, Amber =0)
216 – 246 Reddown, Green=0, Blue=full, Amber =0
247
Blue (Red=0, Green=0, Blue=full, Amber =0)
248-251 Rainbow effect with fade time (fast slow)
252-255 Rainbow effect without fade time (fast slow)
step
step
step
step
step
step
step
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
proportional
Shutter/ Strobe
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
step
step
proportional
step
proportional
proportional
step
0
0-31
32-63
64-95
96-127
128-143
144-159
160-191
13
step
ArcSource Outdoor 16 MC Integral
2
-
-
8
-
-
-
9
192-223
224-255
Random strobe-effects from slow to fast
Shutter open
proportional
step
0 - 255
Dimmer
Dimmer intensity from 0% to 100%
proportional
0 - 255
Dimmer fine
Fine dimmer intensity from low to high
14
Proportional
ArcSource Outdoor 16 MC Integral
7. ArcSource Outdoor 24 MC Integral (SmartWhite) - DMX protocol
Version 1.0
Mode/Channel
1
2
3
1
-
1
2
-
2
-
1
3
-
-
4
-
2
5
-
-
6
Value
Function
Type of control
0 - 255
Warm white LEDs
Warm white LEDs saturation control (0-100%)
proportional
0 - 255
Cool white LEDs
Cool white LEDs saturation control (0-100%)
proportional
0
1-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-247
248
249
250-255
Colour wheel
No function
White 2800 K
White 3200 K
White 3800 K
White 4200 K
White 4600 K
White 5000 K
White 5600 K
White 6300 K
Warm white --> Cool white
Rainbow effect (with fade time)
Rainbow effect
Reserved
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
Strobe
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
Random strobe-effects from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
0 - 255
Dimmer
Dimmer intensity from 0% to 100%
proportional
0 - 255
Dimmer fine
Fine dimmer intensity from low to high
proportional
15
step
step
step
step
step
step
Step
step
proportional
step
step
ArcSource Outdoor 16 MC Integral
8. ArcSource Outdoor 24 MC Integral (Single colour) - DMX protocol
Version 1.0
Mode/Channel
1
2
-
1
1
2
-
3
Value
Function
Type of control
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
Strobe
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
Random strobe-effects from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
0 - 255
Dimmer
Dimmer intensity from 0% to 100%
proportional
0 - 255
Dimmer fine
Fine dimmer intensity from low to high
proportional
16
ArcSource Outdoor 16 MC Integral
9. Control menu map
Default settings=Bold print
Menu Level 1
Menu Level 2
Menu Level 3
DMXA
0001
Set DMXA
0001-0512
InFo
POn Time.
Total
Menu Level 4
Reset
DMX In
REd
0-255
:
Temp.
Dimmer F
0-255
Current
Led
Board
Highest
Led
Board
High Res.
Led
Board
Sw Ver.
IC-1
IC-2
PErS
DMX Pres
Mod.1
Mod.2
Mod.3
Mod.4
RGB Cnt
Active, Deactive
DMX In
Wired
Wireless
Analog 0-10V
M. FTime
0.1-25.5
Display
Turn
On/Off T
On, Off
17
Menu Level 5
Menu Level 6
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Menu Level 4
Contrast
0-100%
Backlight
0-100%
Temp Uni
°C, °F
I Ef Pos
Red
0-255
Green
0-255
Blue
0-255
White (Amber)
0-255
CTC
0-255
C Wheel
0-255
Strobe
0-255
Dimmer
0-255
Dimmer F
0-255
Menu Level 5
Menu Level 6
Prg End
1-40
Store
Defaults
Manual
Red
0-255
:
:
Dimmer F
0-255
Auto Run
Off
Test Prg
St ALone
Test
Prog 1
:
Prog 3
Pr Play
Test Prg
Prog 1
:
Prog 3
Pr Edit
Prog 1
Step 01
18
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Menu Level 4
Menu Level 5
Menu Level 6
:
:
Red
0-255
Prog 3
Step 40
:
:
F.Tim.
0-25.5 sec
Copy
Special
rdM Low
rdM High
LED type
RGBW
Sin. Col.
Smart. W.
RGBA
Wireless
Stat, Unlink
IniBlink
On, Off
Hold DMX
On, Off
Flicker freeM
On, Off
Adjust
DMX Val
Red
0-255
:
Cal Col
Dimmer F
0-255
Red C
0-255
:
Store
Cal.temp
2700K
Red C
0-255
Grn C
0-255
Blu C
0-255
Whi C
0-255
Store
3200K
4200K
5600K
8000K
Cal.Def.
19
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Sw Upd
No/Yes
Menu Level 4
Menu Level 5
Menu Level 6
RDM menu (e.g. for the Robe Universal Interface WTX, because this device cannot display 2-row display of the
ArcSource Outdoor 16 MC Integral)
Default settings=Bold print
Menu Level 1
Menu Level 2
Menu Level 3
A001
Dm.Ad.
A001
InFo
Poti
totl
Menu Level 4
rSEt
DM. In
rEd
0-255
:
tEMP.
dim
0-255
Cur. t.
LEd
board
Hi.tE.
LEd
board
rSEt.
LEd
board
VErS.
IC1
IC2
PErS
DM.Pr.
Mod.1
Mod.2
Mod.3
Mod.4
DM. In
Wird
rAdI
AnL.d.
M.F. ti.
0.1-25.5
tEM.u.
°C, °F
20
Menu Level 5
Menu Level 6
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Menu Level 4
Menu Level 5
Menu Level 6
In.Po.
rEd
PrG 1
St. 01
P End
1-40
:
:
rEd
0-255
PrG3
St. 40
:
:
S.tim.
0-25.5
GrEn
bLuE
WhIt
CtC
C.vhE
Stro
dimr
F.dim
SAVE
dF. SE.
Man. M.
rEd
0-255
:
:
Dim F
0-255
Auto
OFF
tESt
St. AL
tESt
PrG 1
:
PrG 3
PLAY
tEst
PrG1
:
PrG3
Edit
21
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Menu Level 4
Menu Level 5
Menu Level 6
F.tim.
0-25.5
COPy
SPEC
rdM. L.
rdM. H.
t. LEd
rGbV
Si. Co.
SM. Vh.
rAdI.
Stat
UnLi
I.bLi.
On, Off
HOLd
On, Off
F. FrE
On, Off
Adj
Man.M
rEd
0-255
:
CAL. C.
F. dinr
0-255
rEd. C.
0-255
GrE.C
0-255
bLu.C.
0-255
VhI.C.
0-255
SAVE
CAL. t.
2700
rEd. C.
0-255
GrE.C
0-255
bLu.C.
0-255
VhI.C.
0-255
SAVE
3200
4200
5600
8000
CA.dF.
22
ArcSource Outdoor 16 MC Integral
Menu Level 1
Menu Level 2
Menu Level 3
Upd
no/yES
Menu Level 4
Menu Level 5
Menu Level 6
10. Fixture menu
The control panel menu allows to set the fixture according to your needs, obtain information on its operation and
manual control of all effects.
The four control buttons on the front have the following functions:
- ESCAPE button-leaves menu without saving changes.
- ENTER button- enters menu, confirms adjusted values and leaves menu.
- UP and - DOWN buttons - move between menu items on the same level, sets values.
10.1 Fixture Address
Use this menu to set the DMX address of the fixture.
Set DMXA --- Set DMX address. Select this submenu to set a DMX start address.
To set a DMX address.
1. Use the UP/DOWN buttons to find “ DMXA/0001“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired start address.
4. Press the ENTER button to confirm the choice.
Note: After switching on, the ArcSource Outdoor 16 MC Integral will automatically detect whether DMX 512 data is
received or not.
If there is no data received at the DMX input, the display will start to flash with actually set address.
10.2 Fixture information
Use this menu to read useful information about the fixture status.
To display desired information.
1. Use the UP/DOWN buttons to find the “ InFo“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select the required menu item.
4. Press the ENTER button to confirm the choice.
Pon Time ---Power On Time. Use the menu item to read the number of operation hours of the fixture.
Total - the function shows the total number of the operation hours since the ArcSource Outdoor 16
MC Integral has been fabricated.
Reset - the function shows the number of the operation hours that the ArcSource Outdoor 16 MC
Integral has been powered on since the counter was last reset.
In order to reset this counter to 0 you have to press and hold the UP and DOWN buttons and at the
at the same time press the ENTER button.
DM In ---DMX values. Select this function to read DMX values of each channel received by the fixture.
Temp ---Fixture Temperatures. Select this menu to read the temperatures of the fixture:
23
ArcSource Outdoor 16 MC Integral
Current --- the current temperature of the fixture inside.
Highest - the menu item shows the max. temperatures of the fixture inside since
the ArcSource Outdoor 16 MC Integral has been fabricated.
High Res. --- the menu item shows the maximum temperatures of the fixture inside since
the counter was last reset. In order to reset this counter to 0 you have to press and hold the UP
and DOWN buttons and at the at the same time press the ENTER button.
Measuring points: Led-temperature on the PCB with LEDs
Board- temperature on the control board of LEDs
Note: The ambient temperature should not exceed 40°C.
The temperatures can be displayed in either °C or °F units - see option “tEM.U“ in the menu “Pers“.
Sw Ver ---Software Versions. Select this function to read the software version of the fixture processors.
10.3 Personality
Use this menu to modify the ArcSource Outdoor 16 MC Integral operating behaviour.
DMX Pres --- DMX preset. Select this menu item to set a desired DMX mode. Please refer to the chapter "DMX
protocol" for detail description of each DMX mode.
RGB Cnt ---RGB counting. If this function is active, the white channel (channel 4) uses red, green and blue chanels
in proportional relation to ensure max. light output in a white colour ( if white channel =full, also red, green and
blue channels are full). This function is active for RGBW variant only.
DMX In --- DMX input. Use the menu to select mode of receiving DMX signal:
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt wireless module (wireless DMX version
only).
Analog 0-10V --- Analog dimmer. If this option is selected, the dimmer channel can be controlled
via DC voltage (0-10V) connected between pins 1 (data ground) and 3 (Data +) of DMX input of
the fixture (0-data ground, 10V-data +).
Procedure of setting:
1. Set fixture´s channels at desired values (by means of menu item Init Effect Positions “I. Ef.Pos”).
2. Disconnect DMX controller
3. Select option “Analog 0-10V” from menu DMX input
4. Connect DC voltage to the DMX input of the fixture
M FTime --- Max. Fade time. Select this menu item to set a desired max. fade time (0-25.5 sec.). This adjusted fade
time influences fade of Red, Green, Blue,White and dimmer during DMX operation:
If time between two receiving DMX values is > than fade time set in the item “M Ftime“, the entire adjusted fade
time will be used.
If time between two receiving DMX values is < than fade time set in the item“M Ftime“, the adjusted fade time will
be reduced to fill entire time between the two receiving DMX values.
e.g “M Ftime“=2sec. and fixture has received Red=0 DMX, after 5 seconds will receive Red=255 DMX. It means, that
red will go to full intensity during 2 seconds.
“M Ftime“=8 sec. and fixture has received Red=0 DMX, after 5 seconds will receive Red=255 DMX. It means, that
red will go to full intensity during 5 seconds. (Max, fade time is reduced from 8 sec. to 5 sec.).
Display. --- Display adjusting. This function allows you to change the display settings.
24
ArcSource Outdoor 16 MC Integral
Turn - This function turns the display by 180°.
On/Off T - This function allows you to keep the display permanent on or turn it off two minutes
after last pressing any button on the control panel.
Contrast - Use this function to adjust contrast of the display (0-100%).
Backlight - Use this function to adjust backlight of the display (0-100%).
Temp U --- Temperature Unit. Use this menu in order to display the fixture temperatures in desired units: °C or °F.
I Ef Pos --- Init effect positions. Use this function to set all effects to the desired positions to which they will move
after switching the fixture on (if DMX is not being received).
Defaults --- Default Settings .The menu item sets all fixture parameters to the default (factory) values.
10.4 Manual mode
Use this menu for control the fixture without connected DMX console.
To control fixture channels.
1. Use the UP/DOWN buttons to find “ Manual“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired effect (channel).
List of control channels:
“Red” - red LEDs saturations
“Green“ - green LEDs saturations
“Blue“ - blue LEDs saturations
“White“ (Amber) – white (amber) LEDs saturations
“C TC“ - a colour temperature correction
“C Wheel“ - a virtual colour wheel
“Strobe“- a strobe, shutter
“Dimmer“- a dimmer
“Dimmer F” a fine dimmer
4. Press the ENTER button and use the UP/DOWN buttons to set value , press the ENTER button to confirm it.
10. 5 Test sequences
Use this menu to run demo-test sequences without an external controller, which will show you some possibilities
of using the ArcSource Outdoor 16 MC Integral.
10.6 Stand-alone setting
The fixtures on a data link are not connected to the controller but can execute pre-set programs which can be
different for every fixture.
Auto Run --- Automatic playback. This function allows you to select the program which will be played after
switching the fixture on. Selected program will be played continuously in a loop.
1. Use the UP/DOWN buttons to find “ Sta Alone“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select “ Auto Run“ item.
25
ArcSource Outdoor 16 MC Integral
4. Press the ENTER button.
5. Use the UP/DOWN buttons to select desired program.
6. Press the ENTER button to confirm the choice.
Pr Play --- Playing program. By enter to this menu a complete overview of all programs is offered, from which the
program to be run can be selected.
1. Use the UP/DOWN buttons to find “Pr Play“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired program.
4. Press the ENTER button. The selected program runs in a loop.
Pr Edit --- Editing a program. The fixture offers 3 freely editable programs (Prog.1-Prog.3) each up to 40 steps.
Every program step includes a fade time-the time taken by the step´s channel status to reach the desired level and
a step time-the total time occupied by the step in the program.
E.g. If “F.tim.“=5 second and “S.tim.“=20 second, effects will go to the desired position during 5 seconds and after
that they will stay in this position for 15 seconds before going to the next prog. step
1. 1. Use the UP/DOWN buttons to find “ Sta Alone“ menu and press the ENTER button.
2. Use the UP/DOWN buttons to select “Pr Edit“ menu and press the ENTER button.
3. Use the UP/DOWN buttons to select a program you want to edit (Prog.1-Prog.3) and press ENTER button.
4. Use the UP/DOWN buttons to select a desired program step ("Step 01" - "Step 40") and press ENTER
button.
5. Use the UP/DOWN buttons to select a channel you want to edit and press the ENTER button.
List of editable items:
“Prg.En” - a total number of program steps (value 1-40). This value should be set before start
programming (e.g. if you want to create program with 10 steps, set Prg.En=10).
“Red” - red LEDs saturations
“Green“ - green LEDs saturations
“Blue“ - blue LEDs saturations
“White“ (Amber) – white( amber) LEDs saturations
“C TC“ - a colour temperature correction
“C Wheel“ - a virtual colour wheel
“Strobe“- a strobe, shutter
“Dimmer“- a dimmer
“Dimmer F” a fine dimmer
“F.tim.“- a fade time, (0-25.5) seconds
“S.tim.“ - step time, value (0-25.5) seconds
“COPY“. – this item duplicates the current prog. step to the next prog. step. The item “Prg En” is increased
automatically.
6. Use the UP/DOWN buttons to set a DMX value of the channel and then press the ENTER button.
7. Use the UP/DOWN buttons to select next channel and press the ENTER button.
8. After having set all channels in the current program step, press the MODE button to go by one menu level
back and select another program step.
10.7 Special functions
rdM Low --- RDM Code.This menu item shows the first part of the RDM identification code.
rdM High --- RDM Code. This menu item shows the second part of the RDM identification code.
26
ArcSource Outdoor 16 MC Integral
LED type --- LED colour variat. This menu allows to set desired colour variant according to connected LED module.
RGBW – RGBW variant.
Sin. Col.– Single colour variant.
Smart W.– Smart white variant
RGBA – RGBAmber variant.
Note: The menu items and DMX chart will be changed according to set colour variant!
Wireless --- Wireless state. This menu serves for reading
of the state of wireless operation (only Wireless DMX).
Unlink - The item serves for unlinking the fixture from the transmitter (only Wireless DMX version)
IniBlink --- Initial blink. If this function is on, the fixture makes auto-calibration (each LED colour lit on 100% for
short time) after switching the fixture on.
HoLd DMX --- If the function is on, the last received DMX values are held in case, that DMX data receiving was
interrupted (e.g. disconnected DMX controller).
Flicker Free M ---Flicker free mode. If the function is on, the light flickering visible in cameras is corrected but
colour uniformity is worse.
Adjust - Adjustment. The menu allows the fine adjustment of colours.
DMX Val- DMX values. Use the menu to set DMX values of fixture´s channels.
Cal Col - A calibration o red, green, blue and white colours by means of an automatic calibration
with a factory equipment. This function is active for RGBW variant only
Red C – red LEDs saturation (0-255)
Grn C – green LEDs saturation (0-255)
Blu C – blue LEDs saturation (0-255)
Whi C – white LEDs saturation (0-255)
Cal Temp – Selection of colour temperature for manual calibration: 2700K, 3200K, 4200K, 5600K,
8000K.
Manual colour calibration:
1. Connect the fixture to the mains , go to the “Manual” menu and set the shutter,dimmer, red, green, blue
and white channel at 255DMX and let the fixture heat up (cca 1 hour).
2. Go to the “Manual” menu and set the C Wheel at 1 DMX (2700K)
3. Go to the “CalCol” menu, select “2700K” item and by means of the Red C, Green C, Blue C and White C
items adjust the 2700K colour temperature as exactly as possible (∆u´v´= 0).
After calibration, press the “Store“ item to save adjusted values.
4. Go to the “Manual” menu and set the C Wheel at 4 DMX (3200K).
5. Go to the “CalCol” menu, select “3200K” item and by means of the Red C, Green C, Blue C and White C
items adjust the 3200K colour temperature as exactly as possible (∆u´v´= 0).
After calibration, press the “Store“ item to save adjusted values.
6. Repeat this procedure for rest of colour temperatures (4200K, 5600K,8000K).
SW Upd --- Software update. The menu item allows you to update software in the fixture via either serial or USB
port of PC.
The following are required in order to update software:
- PC running Windows/2000/XP/7/8/10 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX P/N.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note1: Software update should execute a qualified person. If you lack qualification, do not attempt the update
yourself and ask for help your Anolis distributor.
27
ArcSource Outdoor 16 MC Integral
Note 2: DMX address, programs and all items in the menu "PErS" will be set to their default values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the Anolis web site at WWW.anolis.cz.
2. Make a new directory ( e.g. Anolis_Uploader) on your hard disk and download the software into it.
3. Unpack the program from the archive.
II.Fixture software updating.
1. Determine which of your port is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
- with the DMX input of the Robe Universal Interface if you using the USB cable.
Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and the fixture on.
Make sure the lamp is switched off (only if the fixture involves a lamp).
2. Switch the fixture to the updating mode:
1 Use the UP/DOWN buttons to find “SPEC.“ menu.
2 Press the ENTER button.
3 Use the UP/DOWN buttons to select “ uPd.“ item.
4 Press the ENTER button
5 Use the UP/DOWN buttons to select “ yES“ option
6 Press the ENTER button
Note: If you do not want to continue in software update, you have to switch off and on the fixture
to escape from this menu.
3. We recommend to cancel all running programs before start of the Software Uploader.
4. Run the Software Uploader program. Select desired COM and then click on the Connect button.
Select COM if the
seriál port is used.
Select Robe
Universal Interface
if the USB port is
used.
If the connection is OK, click on the Start Uploading button to start uploading. It will take several minutes
to perform software update. If the option "Incremental Update" is not checked, all processors will be
updated (including processors with the same software version).
If you wish to update only later versions of processors, check the Incremental Update box.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is finished, the line with the text “The fixture is successfully updated‘will appear in
this window and the fixture will reset with the new software.
Note: In the case of an interruption of the upload process (e.g. power cut), the fixture keeps the updating mode
and you have to repeat the software update again.
For example: The fixture was switched off before finishing software upload. After switching again the fixture on,
the fixture is still in the updating mode and the display is dark. Restart the Software Uploader program and repeat
software update from your PC.
28
ArcSource Outdoor 16 MC Integral
11. RDM
This fixture is ready for RDM operation.RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications for
DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for ArcSource Outdoor 16 MC Integral is the following.
Parameter ID
Discovery command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
SET command
GET command
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
DEVICE_LABEL
*
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_LEVEL
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
Please, see the Robe Universal Interface user manual for detail description of RDM operation.
29
ArcSource Outdoor 16 MC Integral
12. Technical specifications
Power supply
• Electronic auto-ranging
• Input voltage: 100 - 240V AC, 50-60 Hz
• Max. power consumption: 42W (power factor=0.75, I=0.24A at 230V)
Optic & Effects
• Light source: 4 x high power multi-chip LEDs
• Available optical systems: 11°, 26°, 36°
• RGBW/RGBA colour mixing (RGBW/RGBA version only)
• Built-in colour macros (RGBW/RGBA version only)
• Adjustable strobe sequences
• White colour balance adjusting (RGBW version only)
• typical Lumen maintenance: 70%@ 60,000 hours
Control
• Protocol: USITT DMX 512, RDM
• DMX modes for RGBW/RGBA version: 4 (2,3,4,9 control channels)
• DMX modes for Single Colour version: 3 (2,2,6 control channels)
• DMX modes for Single Colour version : 2 (1,3 control channels)
• Operation modes: DMX, Stand-alone
• Setting and addressing: Two-row LCD display & control buttons or via RDM
• 3 user editable programs each up to 40 steps.
Wireless DMX/RDM module (for wireless DMX version only: ArcSource Outdoor 16 MC Integral/W)
• Compliance with USITT DMX-512 (1986 & 1990) and 512-A
• Full DMX fidelity and frame integrity
• Auto sensing of DMX frame rate and frame size
• <5ms DMX latency
• Operational frequency range of 2402-2480 MHz
• Producer: LumenRadio
Antenna (for wireless DMX version only)
• Max. gain: 5dBi
Strobe
• Strobe effect with variable speed (max. 20 flashes per second)
• Pre-programmed random strobe pulse-effects
Dimmer
• Smooth 16-bit dimming from 0 - 100 %
Rigging
• Via two slots in the fixture base
Temperatures
• Maximum ambient temperature: 45° C
• Maximum housing temperature: 80° C
Total heat dissipation
• 140 BTU/h (calculated)
30
ArcSource Outdoor 16 MC Integral
Dimensions (mm)
ArcSource Outdoor 16 MC Integral
Junction box
Top hat
31
ArcSource Outdoor 16 MC Integral
Half top hat
Tilt adjustment range
• 90°
Weight
• 4.7 kg
Protection factor
• IP 67
Impact resistance
• IK 06
Connection
• Data/power cable: Li9Y11Y 3xAWG16+2xAVG24 shielded and jacketed
• junction box
• connection between LED unit and control unit: LiYY 8xAWG22 UL Style 2517/CSA O.D. 6,70mm with
connectors (1x Chogori 08BMMA-SL8001 (male)- at LED unit and 1 x CGRBDU-08BFFA (female)-at
Control unit)
Note. In the case that the control unit is installed separately, max. length of connection cable between the
control unit and the LED unit should not exceed 20 metres.
32
ArcSource Outdoor 16 MC Integral
Included items
• 1 x ArcSource Outdoor 16 MC Integral
• 1 x Junction box (P/N 99714080)
• 4 x reducing seal (P/N 13051388) - for diameter of cable 4-8mm
• 1 x User manual
Optional Accessories
• Top Hat ArcSource Outdoor 16 MC (P/N. 10980290)
• Half Top Hat ArcSource Outdoor 16 MC (P/N. 10980291)
• Stand for ArcSource Outdoor 16 MC (P/N. 1098 0279)
13. Cleaning and maintenance
DANGER !
Disconnect from the mains before starting any cleaning or maintenance work
Rinse off loose dirt with low pressure water spray. Wash the housing with a soft brush or sponge and a mild, nonabrasive washing detergent. Rinse it.
There are no serviceable parts inside the device.
Maintenance and service operations are only to be carried out by a qualified person.
Should you need any spare parts, please use genuine parts.
Specifications are subject to change without notice.
October 2, 2017
33