Configuration Tool

Cree Configuration Tool With SmartCast® Technology
Wireless Configuration Tool
Includes: CCT-CWC-1
IMPORTANT SAFEGUARDS
Installation Instructions
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Caution: The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C (212°F) or dispose of in fire. Replace
batteries with CR123A type only. Use of another battery may present a risk of fire or explosion.
2. Dispose of used batteries properly. Keep away from children. Do not disassemble and do not
dispose of in fire.
3. Replace batteries at the same time using fresh cells only.
4. Avoid direct eye exposure to forward facing LED.
5. Indoor use only and suitable for damp locations.
6. Any changes or modifications to these devices not explicitly approved by manufacturer could void
your authority to operate this equipment.
• USB cable ( part number:
LAH00206X0001A0 ) can be used to
power the device in the absence of
working batteries.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
1
2
Up
LCD Display
Keypad
Battery Compartment
Selection
LED
Device
Select
Cancel/
Back
USB (Mini B) Port
OK
Down
Power
Front View
UNIT DESCRIPTION- Figure 1
The Cree Configuration Tool is used to set up
and configure Cree SmartCast™ Technology
enabled devices. Revolutionary OneButton™
Setup enables automated setup of luminaires
and dimmers with little to no installer
intervention. With the press of a single button,
SmartCast™ Technology enabled luminaires
and dimmers create their own secure network,
learn about the spaces they’re installed in and
form logical groups.
BATTERY INSTALLATION
STEP 1:
Remove battery cover and install the two
1 of 2
Bottom
View
included CR123A batteries in the orientation
indicated by label on the device.
STEP 2:
Replace battery cover.
Set Up New Installation
STEP 1:
Turn Configuration Tool on using power
button. Cree logo is displayed when tool starts
up. See Figure 2.
STEP 2:
Once ready, the Configuration Tool will prompt
to begin OneButton™ Setup. Be sure to have
all devices powered on before beginning
OneButton™ Setup. If other lighting networks
are found, select Set Up New to setup a new
installation.
STEP 3:
OneButton™ Setup will create a secure
lighting network, calibrate daylighting, and
form luminaires and dimmers into groups.
The Configuration Tool will display progress
throughout this process.
Step 4:
OneButton™ Setup is complete and your
installation is ready to use. Changes to groups
and other settings can be made from the Main
Menu.
LPN00212X0006A1_C
3
Main Menu
After starting the Configuration Tool and setting up a new installation or
joining an existing installation, you will be brought to the Main Menu. See
Figure 3.
Modify Groups
• Create new groups by selecting devices
• Merge existing groups together
• Add devices to an existing group
• Ungroup an existing group
Device Settings
• Make changes to motion sensor settings, including timeout and
occupied/unoccupied levels
• Make changes to daylight harvesting settings.
Test Occupancy
• Place motion sensors into a test mode where they will have a short
timeout and operate individually to verify operation and placement.
Advanced
• Setting/Changing a PIN for the Configuration Tool
• Device replacement
• Add new devices to the existing lighting network
• Joining a lighting network
• Resetting devices or the lighting network
CLEANING
INDUSTRY CANADA STATEMENT
Clean using a cloth dampened only with water and a little mild
detergent. Use of solvents or hydrocarbon-based cleaners may cause
permanent damage.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device. In addition, this device complies with ICES-003
of the Industry Canada (IC) Regulations.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
This device has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the device is operated in a commercial environment.
This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
In addition, this device complies with ICES-003 of the Industry Canada
(IC) Regulations.
The LED in the front of this device operates within Risk Group 1 levels
per IEC 62471.
© 2016 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change.
See http://lighting.cree.com/warranty for warranty and specifications. Cree® and SmartCast® are registered trademarks, and
the Cree logo, and OneButton™ are trademarks of Cree, Inc.
www.lighting.cree.com
2 of 2
LPN00212X0006A1_C