model 92-88 cable hook/v-rung accessory

READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING WORK.
IF YOU DON'T UNDERSTAND CALL 724-588-8600 FOR ASSISTANCE.
MODEL 92-88 CABLE
HOOK/V-RUNG ACCESSORY
THIS KIT IS TO BE USED ONLY ON WERNER CO.
FIBERGLASS EXTENSION LADDERS
with RUNGS ATTACHED DIRECTLY TO RAILS
(No Rung Plates)
WARNING:
1. Failure to comply with all instructions may result in serious injury.
2. Make sure this kit fits your ladder. Refer to the application chart on the outside of the kit’s packaging. If you have any
questions concerning the use of this kit on other Werner Co. products, call 724-588-8600 for assistance.
3. Before installing this kit, identify all kit components. If any components are missing or damaged, return the kit to place
of purchase. Do not substitute any components.
4. Inspect the ladder before installing this kit. Repair or replace any damaged or missing ladder parts before using the
ladder. Use only Werner Co. repair or replacement parts. If unable to repair, discard the ladder.
COMPONENTS IN KIT
(1)
(8)
(8)
(2)
(1)
(2)
TOOLS REQUIRED
CABLE HOOK/V-RUNG ASSEMBLY
#10-32 X 5/8" BOLTS
#10-32 LOCKNUTS
HOLE TEMPLATES
CABLE HOOK/V-RUNG INSTRUCTION LABEL
COVER PLATES
#10-32 X 5/8"
BOLTS
#10-32
LOCKNUTS
CABLE HOOK/V-RUNG ASSEMBLY
CABLE HOOK/V-RUNG
SAFETY INSTRUCTIONS
A
TOP
OF
LADDER
B
P/N 52695-01
HOLE
TEMPLATES
WARNING: Failure to follow
all instructions may result
in serious injury.
If you have any questions on
safe usage, etc. call or write:
Werner Ladder Co.
93 Werner Road
Greenville, PA 16125-9499
724-588-8600
1.This ladder is designed to
be used with the fly on top
of the base as shown in the
label above.
2.Locks are to be engaged as
shown in the label above.
USE
STORED
POSITION POSITION
3.Properly lock cable hooks
into use position before
climbing.
4.Never lean ladder on
hooks. When using against
a building or other solid
surface, first fold hooks
into stored position.
5.Never hang ladder from
cable hooks. The cable
hooks are designed for use
as a safety precaution – not
as a means of total support
for the ladder.
6.Always tie off ladder to
cable to prevent sliding.
7.Also read and follow all
other instructions on ladder.
© 1995 / 1998 Werner Ladder Co.
P/N 53201-01
CABLE
HOOK/V-RUNG
INSTRUCTION
LABEL
COVER
PLATES
WernerParts.com
(1)
(2)
(1)
(1)
(1)
(1)
(1)
HACKSAW
3/8" WRENCHES
DRILL
13/64" DRILL BIT
CHISEL
HAMMER
CENTER PUNCH
NOTICE: THIS KIT IS TO BE INSTALLED IN
PLACE OF THE TOP RUNG IN THE
FLY SECTION
Remove Top Rung In Fly Section
1. Using a saw, cut rung close to each side rail. see
CUT
Figure 1.
2. Using a saw, cut through rung and ferrule in four
places. See Figure 2. (Do not cut beyond edge
SIDE RAILS
of ferrule.)
FIGURE 1
3. Using a chisel and hammer, gently tap the ferrule
to break the segments away from the side rails.
SIDE RAILS
FERRULE
RUNG
4. Tap parallel to the side rail web. Do not attempt to
drive ferrule through web. See Figure 2 and 3.
CUT
SIDE RAIL
WEB
You now have exposed the rung hole in the side
CUT THIS
DEPTH
rail.
See Figure 4.
TAP OUT THESE DO NOT CUT BEYOND EDGE OF FERRULE
SECTIONS FIRST
FIGURE 2
(STEP #3)
5. Repeat steps 2 through 4 on the opposite side.
WARNING: If you have damaged the
ladder side rail you should not proceed.
THIS WAY
FIGURE 3
FIGURE 4
WernerParts.com
NOT THIS WAY
INSTRUCTIONS CONTINUED
Attach the Cable Hook/V-rung Assembly
6. Place the template on the outside of the side rail
RIVETS
C
web with the template hole pattern ‘A’ coinciding
with the side rail hole pattern ‘F’. See Figure 5.
D
7. Center punch at the crossed lines next to the
E
template Letters ‘B’. Using a 13/64" diameter bit,
drill through the side rail web at the punch marks.
F
NOTE: These holes must be precisely drilled to
A
TOP
OF
LADDER
properly assemble the accessory to the ladder.
FORMER TOP
RUNG LOCATION
8. Repeat steps 6 and 7 on the opposite side.
TEMPLATE
CENTER PUNCH AT ALL
CROSSED LINES
FIGURE 5
CABLE
HOOK
B
P/N 52695-01
CABLE
HOOK
FRONT
#10-32
LOCKNUTS
REAR
V-RUNG
#10-32 X 5/8"
MACHINE
SCREWS
V-RUNG
LADDER
FLY
SECTION
LADDER
BASE
SECTION
FIGURE 7
FIGURE 6
9. Position the back up plate and the cable hook/
10. Attach cable hook/V-rung instruction label
V-rung assembly so that the cable hook and V-rung
approximately 54" to 72" from the bottom of the
are toward the rear of the ladder. See Figure 6 and
base section on the outside of the right-hand side
Figure 7. Using the 3/8" wrenches, attach the cable
rail. Clean surface of the side rail with a
hook bracket to the side rail web with the enclosed
cleaner/degreaser (such as “Formula 409” or
fasteners using template hole patterns ‘A’ and ‘B’.
“Fantastic”, etc.) and allow to dry before
See Figure 5, 6 and 7.
applying label.
WARNING:
DO NOT SUSPEND LADDER FROM CABLE HOOKS. MAKE SURE LADDER BASE IS
SECURE BEFORE CLIMBING. READ AND FOLLOW ALL WARNING LABELS ON LADDER.
WernerParts.com
WERNER CO., 93 WERNER ROAD, GREENVILLE, PA 16125-9499
PHONE (724) 588-8600
www.wernerladder.com
P/N52694-01 © 1998 / 2007 Werner Co.
R1/00; R8/07
WernerParts.com