JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1014 AXLE NUT SOCKET
•
Application: Isuzu model with 4WD.
•
Special cylinder design for suiting the
transmission nut.
•
JTC-1016 INNER CV JOINT PULLER
•
•
Used period: before 2000.
•
JTC-1020 HAND OPERATED FLUID EXTRACTOR (10L)
Fork type tool pulls CV joints with hidden
retaining rings and joints.
•
•
Capacity: 10L
With this tool, the axle assembly is popped out of
trans axle without damage to transmission case
or inside roller bearing.
•
Special patented design for releasing the
pressure.
•
Larger base to prevent falling while operating.
Open Rate: 63mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
By manpower to push create vacuum pressure
for extracting fluid in any space.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1024 PNEUMATIC OIL & LIQUID DISPENSER
•
•
•
•
6 liters two in one extracts, and pumps
dispenser.
Specially designed for using on narrow and
difficult to reach spaces.
Fixing valve and safety cup for automatic
shut-off extract.
Content:
1.2m PU hose with flexible rubber nozzle.
1m nylon hose.
6sets / 11kgs / 12kgs / 3.6'
JTC-1025 PNEUMATIC BRAKE BLEEDER
JTC-1026 BRAKE OIL FILLER
•
•
Economical-fast and easy, reduces labor costs.
•
To fill brake oil easily.
Versatile-handles, most standard and ABS brake
systems.
•
12 sets / 7kgs / 8kgs / 1.8'
•
•
Clean-collects old brake fluid without spillage.
•
•
•
•
•
•
Silicon suction assembly with universal rubber fitting.
Quiet-integrated silencer for a quieter working
environment.
Capacity: 2L
Working pressure: 70 - 170psi
Air connection: 1/4"
Temperature range: -3˚ F ~ 140˚ F
12 sets / 15kgs / 16kgs / 6'
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1032 VACUUM OIL EXTRACTING MACHINE & BRAKE
BLEEDER
•
Capacity: 12L
•
Uses compressed air to create a powerful
vacuum to extract any kinds of oil,
gasoline, diesel, water, and others
anytime.
•
JTC-1033 HAND OPERATED OIL PUMP
•
With reservoir capacity 20L.
•
It is suitable for general lubricant and gear oil.
With limpid cup to check the flow anytime.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1034 AIR OPERATED GREASE PUMP
•
Uses air as power to stuck grease into
lubrication points.
•
Suitable for 00# ~ 2# grease.
•
Capacity: 20L
•
Air inlet pressure:4 ~ 9kgs/cm
•
Pressure ratio: 45:1
•
Grease output pressure:180 ~ 405kgs/cm
•
Deliver rate: 30cc/sec
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1035 HYDRAULIC GEAR PULLER SET
•
JTC-1036 OUTER TIE ROD REMOVER
For agriculture machine, automotive, and
industry use.
•
•
Hydraulic ram included for laborsaving.
•
Most models of outer tie rod.
•
Material: SCM415 hardened 40˚ ~ 45˚
•
Material: SCM420 Hardened 42˚
•
Packing: carrying case
•
Packing: each / double blister.
•
1 set / 16kgs / 17kgs / 1.2'
•
6 sets / 24 sets / 29kgs / 30kgs / 2.3'
Two adjustable jaws special designed for
removing.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1045 HAND OPERATED FLUID EXTRACTOR (6.5L)
•
Capacity: 6.5L
•
•
By manpower to push and create
vacuum pressure for extracting fluid in
any space.
Special patented design for releasing
the pressure.
With extra tube storage.
•
Heat-resistance Temperature: 60℃
•
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1050 PNEUMATIC & HAND OPERATED FLUID
EXTRACTOR
JTC-1129 PITMAN ARM PULLER
•
•
•
Heavy duty forged alloy steel yoke.
Capacity: 10L
•
Pneumatic and manual operation fluid extractor of
non-sparkle.
Heat treated center screw.
•
•
Three air outlets with check valve design for quick
and easy to exhaust the air from the extractor.
Remove tie rod ends and pitman assemblies from
many light trucks.
•
Opening size: 27mm
•
Pull travel: 45mm
•
Easy to operate and suitable for engine oil, gear oil,
brake fluid, water, etc.
•
Provided with a modern design decompression
valve for easy to release the negative pressure.
•
•
All parts are the same as JTC-1020.
Heat-resistance Temperature: 60℃
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1141 TWO SETS BEARING SEPARATOR KIT
•
Bearing separator 9000 and 9005
included.
•
Pull out the bearing with the H-type
beam and bolts.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1143 HYDRAULIC BEARING SEPARATOR PULLER KIT
•
Bearing separator 9025 inside.
•
Effort-saving with the hydraulic screw.
•
Pullout the bearing with the H-type beam
and bolts.
JTC-1145 UNIVERSAL AXLES SLIDE HAMMER SET
•
Increased the cover range with the two axle
pullers.
•
Includes 3-jaw puller and many types of joints.
•
Slide hammer design for removing hub and
repairing dent, etc.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1146 3–JAW INTERNAL & EXTERNAL PULLER SET
•
Size:
Small of internal puller 15mm ~ 30mm
Large of internal puller 30mm ~ 80mm
External puller 15mm ~ 80mm
•
Locking the nut to open 3-jaws and
clip the bearing, and then use the slide
hammer to pull out the bearing.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1212 CLIC–R COLLAR PLIERS
•
•
•
JTC-1217 CV BOOT CLAMP TOOL
Distinctive design for the CV ear type
clamps.
•
Easy to work in narrow spaces.
•
Extra work on nose makes it compact.
For releasing and refitting reusable hose
clip.
For type clic and clic-R.
•
A socket with ratchet is used to turn the
actuating screw for adjustment.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1230 ANGLE LOCATOR
•
Angle adjustable with the magnet
attaching on the align magnet tool
currently working on.
•
Applicable with JTC-1840 or JTC-1002.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1247 BALL JOINT SEPARATOR 19mm
JTC-1257 BALL JOINT SEPARATOR 23mm
JTC-1258 BALL JOINT SEPARATOR 28mm
•
Applicable on powerful structures.
•
Jaws open: 23mm
•
Jaws open: 28mm
•
Stand design to solve space problems.
•
Jaws deep: 25mm
•
Jaws deep: 25mm
•
Jaw open: 19mm.
•
Applicable: Audi, BMW, Citroen, Ford, Mercedes,
Opel, Peugeot, Renault, Rover, Saab, Volvo, VW,
Porsche, Pkw, etc.
•
Applicable: Audi, A4, A6, A8, VW,
Passat after 97, etc.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1259 UNIVERSAL HUB PULLER
•
JTC-1316 BALL JOINT EXTRACTORS 18mm
JTC-1317 BALL JOINT EXTRACTORS 23mm
Readily adjustable sliding legs to pull wheel
hubs more quickly and easily where the
bolt circle does not exceed 7-1/2"
(190.2mm)
•
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
•
For splitting track rod ends, anti-roll
bar mountings, ball joints, etc.
•
A: 18mm
•
A: 23mm
•
B: 36mm
•
B: 45mm
•
Removers press-fit rear brake drums.
•
C: 38mm
•
C: 47mm
•
Striking handle and puller screw included.
•
Special designed to use on most models of
cars.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1318 BALL JOINT EXTRACTORS 29mm
JTC-1319 BALL JOINT EXCTRACTORS 40mm
JTC-1320 BALL JOINT EXTRACTORS 46mm
•
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
•
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
•
For splitting track rod ends, anti-roll
bar mountings, ball joints, etc.
•
A: 29mm
•
A: 40mm
•
A: 46mm
•
B: 62mm
•
B: 62mm
•
B: 76mm
•
C: 62mm
•
C: 76mm
•
C: 100mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1323 UNIVERSAL STRUT NUT TOOL SET
•
•
JTC-1329 CV BOOT HOSE CLAMP CUTTER
The complete sizes for using on most kinds
of cars.
•
Designed easy to cut the stainless clamp.
•
Avoid hurting C.V. Boot.
Contents:
•
Width: Under 10mm
2 pcs central sockets: 5, 10mm
9 pcs central sockets: 4, 5.2, 6, 6.3, 7, 8, 9, 10, 12mm
4 pcs central sockets 5, 6, 7, 8mm
3 pcs central sockets 3, 3.5, 4mm
2 pcs central sockets T50, T60
1 pcs central sockets M12
4 pcs central sockets 8, 9, 10, 11mm
9 pcs central sockets 14, 16, 17, 18, 19, 21, 22, 24, 27mm
5 pcs central sockets 10.5, 12.5, 14, 14.5, 14.5mm
•
Thickness: Under 0.5mm ~ 0.7mm
JTC-1335 MANUAL BRAKE GAUGE SET
•
Distinctive design to give customers an
accurate measurement of how much
brake lining is left without guess work.
•
Size:
Red: 2, 3mm – Bad
Yellow: 4, 5, 6mm – Dangerous
Blue: 8, 10, 12mm – Good
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1336 THIN TYPE BALL JOINT SEPARATOR
JTC-1365 1/2" PENTAGON SOCKET BIT DRIVER 10mm
JTC-1401 HEAVY DUTY COIL SPRING COMPRESSOR
•
Special design for using on ball joint space
limited.
•
For using on most vehicles fitting with girdling
brake systems.
•
Hook engage spring which can be
compressed by turning hex nut.
•
The mini operation space: 6 ~ 7mm.
•
Material: CR-V
•
Jaws capacity: 23mm ~ 280mm
•
Jaws open: 22mm
•
Use with 1/2" Drive wrench
•
Length: 280mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1405 DISC BRAKE PISTON COMPRESSOR (4 PISTONS)
•
JTC-1503 CV BOOT CLAMP INSTALLER
Special wider pusher design to use on 4
pistons vehicle.
•
•
Pusher width: 88mm
•
•
Applicable: BENZ, BMW, and 4 pistons
vehicle.
Installs low-profile clamps used to hold CV boots
on most FWD vehicles.
JTC-1531 CV BOOT CLAMP PLIERS (EXTENSION)
•
For all ear-type clamps.
•
Application: For AUDI, BMW,
CHRYSLER, FORD, GM, HONDA,
MAZDA, MERCEDES, NISSAN, OPEL /
VAUXHALL, VW, etc.
•
Designed to use with a 1/2" extension
handle or torque wrench.
Ratcheting action and built-in cutter to tighten
the clamp quickly and properly.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1541 14 PCS WHEEL HUB RESURFACING KIT
JTC-1546 HOSE CLAMP PLIERS (ANGLE TYPE)
•
To clean impurities in wheel case.
•
Designed with angle type to any space.
•
Contents:
1 - 1/2" grinding slice x 6 pcs
2" grinding slice x 2pcs
Special holder
OPTIONAL PARTS:
•
Swivel tip designed for refitting and release.
•
For clic and clic-r type hose clamp.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1559 HONDA REAR TRAILING ARM BUSH
INSTALLER / REMOVER
•
For replacement of the Honda rear
trailing arm bush.
•
On car maintenance.
•
Hook design to mount the tool on
trailing arm securely.
•
No damage to ABS sensor cable,
trailing arm, and parts close to bush
during the maintenance.
•
Applicable:
Honda CR-V 1996/9 ~ 2002/8.K6.K8
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1619 INNER CV JOINT PULLER
•
Fork type tool pulls CV joints with hidden
retaining rings & joints on 1986 - current
Taurus/Sable.
•
With this tool the axle assembly is popped
out of trans-axle without damage to
transmission case or inside roller bearing.
•
Open Rate: 48mm
JTC-1628 HUB SLIDE HAMMER PULLER
JTC-1708 BRAKE SPRING COMPRESSOR
•
Pulls flange-type rear axles on most late model
passenger cars & light trucks.
•
BIG WINDOW designed for great
visibility during operation.
•
Designed to fit axles with bolts & studs up to
9/16" diameter.
•
Allow fast and easy removal, and
replacement of brake shoe hold-down
springs.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1709 BRAKE SPRING TOOL
•
Hook the brake return spring and screw-up
to lock it for removal and installation.
•
A smart tool to service those breaks that
don’t use anchor pins.
JTC-1727 UNIVERSAL BALL JOINT SEPARATOR
JTC-1733 TIRE CONSUMPTION GAUGE
•
Special design 2-stage operating suits most cars
and light trucks ball joints in steering and
suspension.
•
•
Offset lever permits maximum jaw opening in
30mm and 56mm.
Determine the average tire residual energy
between both positions which is unconsumed
part, and also is a right barometer for safe
driving.
•
•
To brake below tire thread 1.6mm / will bring
inferior effect.
Jaw open: 22mm.
•
•
Applicable: Europe cars.
Offers measurement of tire thread from 1 ~
30mm.
•
For automobile, below 1.6mm thread depth is
recommended for change.
•
For truck, below 2.4mm thread depth is
recommended for change.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1833 CV BOOT CLAMP TOOL
•
•
•
JTC-1836 INNER TIE ROD TOOL (8 PCS)
Work on all CV joint with band-type boot
clamps.
•
•
Works on the inner tie rods with inaccessible wrench flats.
Provides fast proper installation of those
clamps with ease.
This small, inexpensive functional tool for
use with 1/4" or 3/8" width band.
•
Seven crows feet, sizes 1-3/16", 1-1/4", 1-5/16", 1-7/16",
14mm, 17mm and 33.6mm, to engage the wrench flats.
•
The long socket then slips over the tie rod end and
connects to the crows foot.
Many inner tie rod end sockets do not have a complete hex
on the full length of the socket. The rounded socket ends
prevent assess to the wrench flats.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1839 MULTI – PURPOSE INNER TIE ROD TOOL
•
The master tie rod tools easily
replaces inner tie rod ends without
removing the rack and pinion.
•
Capacity: 33 - 42mm
•
Patented.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1840 ALIGNMENT TOOLS
•
With 4 pcs alignment plates.
•
Hydraulic function.
•
Suit for most car.
JTC-1843 BLIND HOLE BEARING PULLER SET
JTC-1911 WHEEL WEIGHT TOOL
•
Open clamps by turning handle clockwise to snug
against the bearing for pulling out evenly without
damaging the parts.
•
Easily removes and replaces wheel
weights, as well as cutting and
crimping.
•
Contents:
•
Made of heat strengthened steel.
Included comfortable vinyl handle
grips.
•
With self-open function spring on the
handle for easier operation.
Shaft: Slide hammer shaft 390mm long
Hammer: 2.15lb. (940g), 100mm L.
Clamps:
8 ~ 10mm (5/16" ~ 13/32"); 10 ~ 12mm (13/32" ~ 15/32")
12 ~ 14mm (15/32" ~ 9/19"); 15 ~ 17mm (9/32" ~ 11/16")
17 ~ 20mm (11/16" ~ 25/32"); 20 ~ 24mm (25/32" ~ 15/16")
25 ~ 29mm (1" ~ 1-1/8"); 30 ~ 32mm (1-3/16" ~ 1-1/4")
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1914 UNIVERSAL BALL JOINT PULLER
•
Special steel for removing the ball pivots
on steering.
•
Jaw open: 17mm
JTC-1915 UNIVERSAL BALL JOINT PULLER
•
•
JTC-1916 BALL JOINT SEPARATOR 22mm
Special steel for removing the ball pivots on
steering arms, steering tie rocks, steering
knuckles, etc.
•
For splitting track-rod ends, anti-roll
bar mountings, ball joints, etc.
•
A: 22mm
Jaw open: 20mm.
•
Max. B: 62mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
JTC-1920 CV BOOT CLAMP PLIERS
•
For ear type clamp.
•
Fits CV joint boots.
•
Also installs perma-Quick type clamps
quickly and easily.
•
Use for filter, cooling system and vacuum
lines.
UNDERCAR SERIES
JTC-1941 INTERCHANGEABLE – FORK SPRING COMPRESSOR
•
Spring compressors are multi-application tools
specifically.
•
Developed for modern macpherson suspensions,
using a range of 3 sets of interchangeable
monobloc forks.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1944 HEADLIGHT ADJUSTING AND BRAKE SPRING
HOOK
•
This tool made from heat treated alloy
steel is specially designed for
removing and installing hard-to-reach
headlight adjusting springs. OAL 6".
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1950 STEERING WHEEL PULLER SET
•
Two specialty pullers in one set including
one flange type puller for removal of
harmonic balancers, timing gear & other
parts with two or three tapped holes. And
a steering wheel, pulley and flywheel
puller.
JTC-1952 PITMAN ARM PULLER
JTC-3429 RUBBER CEMENT FOR TIRE SEAL
•
Heavy duty forged alloy steel yoke.
•
Constituent: Toluene, Crude Rubber
•
Remove tie rod ends and pitman assemblies from
many light trucks.
•
Volume: 250CC
•
12 / 72 / 21.5 / 23 / 2.01'
•
Opening size: 33mm
•
Pull travel: 64mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-3430 TIRE SEAL (5 SHEETS / 25 PIECES)
•
Constituent: Butyl, Silk Cotton
•
Contents: 25 strips of 5 pieces
•
100 / 19.2 / 20.5 / 1.96'
JTC-3431 TIRE SEAL TOOL SET
•
Contents: JTC-3922, JTC-3923, JTC-3429, JTC3430, Portable tool box.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-3460 ROLLER STITCHER
•
Wood handle for light and portable.
•
Bearing inside for using easier.
•
Spec.: φ38 x 5mm
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-3523 VALVE CORE TORQUE TOOL 25Ncm
•
•
•
•
•
•
•
Prevents over or under torqueing.
Serves as both a core remover and installer.
Prevents premature tire failure due to leaking
valves.
Easy and simple to use.
Range of the torque: 25N.cm/2 lbf.in (+-6%)
Valve type: rubber
JTC-3524 VALVE CORE TORQUE TOOL 45Ncm
•
•
•
•
•
•
•
JTC-3922 METAL T–HANDLE CLOSED EYE TOOL
Prevents over or under torqueing.
•
Durable metal T-handle design.
Serves as both a core remover and installer.
•
Chrome-Molybdenum steel tip.
Prevents premature tire failure due to leaking valves.
•
Tip length: 53mm
Easy and simple to use.
•
Changeable tip design.
Range of the torque: 45N.cm/4 lbf.in (+-6%)
Valve type: metal
Color: black
Color: red
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-3923 METAL T – HANDLE RASP EYE TOOL
•
Durable metal T-handle design.
•
Chrome-Molybdenum steel tip.
•
Tip length: 72mm
•
Changeable tip design.
JTC-3926 SNAP IN TIRE VALVE INSTALLER
•
JTC-3932 VALVE CORE REMOVER / INSTALLER TOOL
Steel constructed tool deep threaded head for
positive sealing of all snap-in type passenger car
tire valve stems.
•
For installation and removal of
standard valve cores.
•
Has a screwdriver-style handle.
•
Rubber cover design to protect the rim.
•
Tip diameter: 5.5mm
•
3-position settled.
•
Tip length: 60mm
•
Patented.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4039 RATCHET EXHAUST PIPE CUTTER
•
•
This revolutionary tool works like a
standard ratcheting pipe cutter, but can
handle the larger diameter of exhaust
pipes.
Contents:1 - 1/8 " ~ 2 - 1/2 ", 28 - 67mm,
JTC-4043 FLEXIBLE HOSE CLAMP FOR CLIP–R TYPE
•
For replacement of fuel, oil and water hose with
Clip-R hose clamp.
•
Hose clamp with flexible 630mm wire.
•
Convenient for working hidden areas and long
distance.
JTC-4055 WISHBONE EXTRACTION TOOL
•
Designed groove for adjust the position to
work easily.
•
To push down the wishbone and other
suspension parts, e.g. during the disassembly
of the drive shaft, during replacing the gaiter
or exchange of the wheel bearing. After
loosening the ball joint, the wishbone must, in
most cases, be pushed down against the bush
or stabilizer tension, to pull the joint from the
support.
•
With this lever tool, the work can comfortably
and surely be accomplished by one person.
thickness≦3mm
•
Suit for use on exhaust, tailpipes, thin-wall
copper and steel or stainless tubing.
•
Instructions:
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
JTC-4057 2 PCS EXHAUST PIPE REMOVER
UNDERCAR SERIES
JTC-4058 LIGHTWEIGHT 3–FUNCTIOON TIRE GAUGE – CLIP TYPE
JTC-4064 EXTRA LARGE C DISC OF JTC-1941
•
Designed especially for providing pull out
the exhaust pipe easily.
•
3-function (check, release, inflator) all together
on the press handle.
•
Extra-large disc 1 pc for BMW E38,
Chrysler, and Renault etc.
•
Special designed two-way for use with
17mm open wrench and 3/8 " Dr. ratchet
wrench to adjust bolt to pull out the pipe.
•
•
Operation range:180 ~ 240mm
•
Only use with JTC-1941.
•
Large 80mm gauge with 360° swivel function.
Tube length: 600mm
Lightweight design for easier operation. Weight:
0.63kgs
Accuracy: under 110psi: ±3psi; above 110psi: ±4psi
•
Capacity: 170psi/12bar (1200kpa)
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4065 EXTRA LARGE ROUND DISC OF JTC-1941
•
•
JTC-4069 LOCKING RING W/O EYELET PLIERS
Special designed large round disc with
protective cover for BMW E39, E40 series.
•
Only use with JTC-1941.
•
Specially designed for removing and installing
wheel bearing locking rings which without eyelet.
JTC-4091 UNIVERSAL BUSH REMOVE & INSTALL SLEEVE
SET
•
Universal application of step discs for
bearing bush, silent bearing, hydraulic
bearing, and rubber bearing on many
kinds of different vehicles.
•
20 pcs sleeves: ID φ34 ~ φ72mm (in 2mm
increment)
•
•
•
2 pcs step discs: use with sleeves.
Applicable:TOYOTA, LEXUS, Citroen
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
4 pcs bolts: M10, M12, M14, M16
Length: 450mm
JTC AUTO TOOLS USA
JTC-4098 EXTRA LARGE INNER TIE ROD TOOL
•
UNDERCAR SERIES
JTC-4116 UNIVERSAL JOINT INSTALLER / REMOVER (MID. TRUCK)
JTC-4126 THIN TYPE LARGE BALL JOINT SEPARATOR
The master tie rod tools easily replace
inner tie rod ends without removing the
rack and pinion.
•
To remove and install universal joint of
transmission shaft.
•
Special designed to remove the ball
joint in narrow space.
•
Using C clip as a support to remove the joint.
•
Mini operation space: 6 ~ 7mm.
•
Enormous size than JTC-1839
•
•
Jaws open: 28mm.
•
Capacity: 40 ~ 47mm
Applicable:
Middle truck: MITSUBISHI (CANTER), NISSAN,
TOYOTA, MAZDA, ISUZU, etc.
Patented.
•
Applicable: LUXGEN, etc.
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4133 SUZUKI (JIMNY) FRONT WHEEL NUT SOCKET
(4 HOLES)
•
Special designed to remove the front
wheel nut with 4 holes.
•
Applicable: SUZUKI (JIMNY) 1.3
JTC-4135 ANGLE LOCATOR
•
Special designed to for wheel alignment with
adjustable locator.
•
Magnet diameter: 77mm
•
SIZE: 20(L) x 76(W) x 30(H) mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-4151 COIL SPRING COMPRESSOR
(WISHBONE SUSPENSION)
•
Suitable for lower wishbone diameter
size is smaller than 30mm.
•
Provided a 100Nm torque driver.
•
Available for using air impact.
•
Works well with car working.
•
Wide vehicle applications.
•
Patented on three-point lock key
design.
JTC AUTO TOOLS USA
JTC-4158 TOYOTA DRIVE AXLE NUT INSTALLER &
REMOVER
•
Specially designed to make and
remove the fixing point on the nut of
drive axle.
• 2 pcs in a set. One for making the
fixing point and the other for
removing the fixing point to remove
the nut from drive axle.
• Length: 170mm
• Applicable: TOYOTA, LEXUS
UNDERCAR SERIES
JTC-4164 TOYOTA SUB–FRAME BUSH INSTALLER & REMOVER
JTC-4165 BRAKE CALIPER ADJUSTER
•
Removal and installation of rear rubber mounts
of axle suspension.
•
For rewinding the piston in all collets
type disc brake calipers with
•
On car maintenance. Do not need to remove the
sub-frame.
Applicable: TOYOTA.
•
built-in parking mechanism.
•
Essential for fast and easy pad
replacement and caliper servicing.
•
Applicable: FORD, HONDA, JAGUAR,
MAZDA, MITSUBISHI, NISSAN, ROVER,
SUBARU, TOYOTA with ABS.
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
JTC-4190 BALL JOINT SEPARATOR (HIGH)
•
UNDERCAR SERIES
JTC-4236 LIGHTWEIGHT 3–FUNCTION TIRE GAUGE ACCURATE TYPE
•
Jaw open: 28mm
•
•
•
•
Jaw deep: 40mm
•
•
Inside height: 74mm
•
Applicable: BMW 7 series, BENZ S series,
LEXUS 460, etc.
To remove the ball joint which is longer
than normal vehicles.
All the function and weight are the same as JTC-4058.
Special designed for high accuracy requesting of tire
pressure checking.
Accuracy: between 30 ~ 45psi: ± 1psi, the rest: ±2psi.
Capacity:87psi / 6bar (600KPa).
JTC-4252 10L PNEUMATIC ATF & LIQUID DISPENSER
•
•
•
•
•
•
•
•
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
Use to extract, transfer and dispense fluid quickly,
safely and cleanly.
Non-spark, one man in same step operate.
10L capacity reservoir with volume guide.
Screw valve to allow easy change extract or dispense.
Copper material one touch coupler design for easy
operating.
Air inlet: 1/4"
Avg. Air Cons: 2 CFM
Temperature range: -20°C ~ 60°C
Provide with the safety valve, pre-setting 43 psi (3
Bar), the exceed pressure will be relief automatically.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4306 FORD WHEEL HUB BEARIING TOOL SET – 78mm
JTC-4269 BRAKE SPRING WASHER PLIERS
JTC-4307 FORD WHEEL HUB BEARING TOOL SET – 82mm
•
Universal application for nearly all drum
brakes.
•
Special designed for installing and removing the
wheel hub bearing.
•
Special designed for installing and
removing the wheel hub bearing.
•
•
Operation on car.
•
Operation on car.
•
External diameter of bearing fixing discs: φ78mm.
•
•
Special neck angle provides easy removal
and installation of brake spring washer.
Length: 180.5mm
•
Applicable:
External diameter of bearing fixing
discs: φ82mm.
•
Material: steel
•
Applicable: FORD, Focus, Mondeo.
•
Heat treatment: HRC43° ~ 46°
•
Max angle: 50°
FORD: Focus, CMAX.
MAZDA: M3.
VOLVO: C30, C70, S40, V50
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4319 EXHAUST PIPE EXPANDER
•
Application range: 40 ~ 64mm.
•
Special designed to expend one of the pipe
first While contracting with exhaust pipe
•
Applicable: stainless steel.
JTC-4323 BRAKE DISC & TYRE DEPTH GAUGE
•
Special device that allows the measurement to be
fixed while measuring the disc thickness in
various locations.
•
Brake disc measure range: 0~60mm.
•
Measure tyre depth.
•
Made of Aluminum.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-4328 PLASTIC HAND OPERATED OIL PUMP
•
Tank material: PE; Lid material PP.
•
Capacity: 30L
•
Deliver rate: 75cc/cycle.
JTC AUTO TOOLS USA
JTC-4454 10 PCS TIRE PRESSURE SENSOR REMOVER /
INSTALLER SET
•
Specially designed to remove and install
the TPMS in correct torque.
•
Contents:
Fixed Torque 0.45 Nm Tire valve core installer.
Adjustable Torque 1.4, 3.3, and 4 Nm for
assembling TPMS.
TX-bits T10, T15, T20, and 1/4" bit adapter.
Holder thorn 2mm, and hex wrench.
1/4" deep socket 11, and 12mm.
•
UNDERCAR SERIES
JTC-4459 EUROPEAN CAR BALL JOINT REMOVER (4 SIZES)
JTC-4465 6 BOLT HUB SEPARATOR
•
Specially designed for quick and easy removing
the ball joint connections.
•
Use for removing the 6 holes HUB rear
axle.
•
Applicable:
•
JTC-4817 is optional for using as an
axle slide hammer.
Applicable:
BMW E38, E39, E52, E53, E60, E61, E70, E83, E90, E91, E92,
R50, R52, R53, RR1, RR2, X5.
Mercedes W211, W219, W220 and W230.
PORSCHE 996 Carrera.
AUDI A, AUDI A6 lower suspension ball joint.
•
Size: 24mm, 27mm, 31mm, 36mm.
Applicable: Most brand of TPMS.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
•
TOYOTA HIACE 100 series, 200 series
NISSAN CARAVAN E25 series, E26 series
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4466 FRONT AXLE REMOVAL TOOL SET
•
•
•
This tool set is required when replacing the
front HUB upper screw, brake disc and
bearing, etc.
Specially designed for removing each part
on the front HUB.
JTC-4468 BRAKE DISC RUN–OUT KIT
•
Quickly and easily to check the ball joint abrasion
and brake disc run-out.
•
The pliers can enable the dial gauge to use in
various angles against the brake disc.
This kit includes a Metric calibrated dial gauge.
•
Applicable:
TOYOTA HIACE 200 series: 2WD, 4WD
NISSAN CARAVAN E25, E26 series: 2WD, 4WD.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-4479 JAGUAR AXLE BEARING NUT SOCKET
•
Special tool for removing and installing
the axle camber bearing nut which
with ABS rotor on it.
•
Size: 3/4" Dr. x 12PT.
•
Applicable: JAGUAR XJ8, XK8, etc.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4482 CITROGEN & PEUGEOT BALL JOINT SOCKET
JTC-4487 TOYOTA REAR HANDBRAKE SPRING DRIVER
•
Use for removing and installing the screw
nut of the ball joint.
•
Specially designed tool that can reach deeper to
hold down the spring cup on TOYOTA cars.
•
Use with 35mm/6PT wrench.
•
•
SIZE: Ø51mm/4PT.
Applicable: TOYOTA Camry, Tacoma, Tundra, FJ
Cruiser, 4Runner, and Land Cruiser since 2000.
•
Applicable:Peugeot 405/Citroen.
JTC-4492 UNIVERSAL HUB BEARING REMOVER /
INSTALLER
•
Specially designed to extract and
install the Hubs and singular wheel
bearings of spindle assemblies.
•
Designed for FWD, RWD and AWD
vehicles with independent suspension
and a roller ball bearing.
Applicable:
•
FWD VW, AUDI and some Asian vehicles.
RWD Mercedes, Porsche, BMW and some
European vehicles.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
JTC-4514 BOIL TEST BRAKE FLUID ANALYZER
•
True boiling testing base on SAE J1730.
•
Straight-stand design, for both nimble and
stabile.
•
Less fluid wastage via the content cup
•
User friendly, one button to complete the
test
•
UNDERCAR SERIES
JTC-4528 REAR TRAILING ARM BUSH INSTALLER / REMOVER
(FORD, MAZDA, VOLVO)
•
The spider arm can be trimmed to fit the
seal, and keep the seal centered during
installation.
By using this tool can insert the bush to the correct
depth.
•
By using the long handle can install the
pinion seals in a flexible way.
Applicable:
•
•
Applicable: 32mm-60mm
•
Specially designed for easy removal and installation of
the rear arm bush.
•
•
Mazda 3 BK 03 ~ 08, BL 09 ~
PREMACY 05 ~ 10,
AXELA03 ~ 09.
5 CR 05 ~ 10
Ford C-Max 03 - 07
FOCUS I CAK 98 - 05, CB4 08 - 11, II 04 - 08
Kuga CBV 08 ~
Volvo S40 II 04 ~, V50 04 ~
Durable ceramic core, available for racing
fluid.
•
JTC-4537 UNIVERSAL SEAL INSTALLER
OEM bush number: 98AG 5K896 AB
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
Contents:
Hex cap screw x1
Washerx1
Handle x1
Small spider x1
Large spider x1
Spider insert x1
63mm driver x1
76mm driver x1
JTC AUTO TOOLS USA
JTC-4539 ATF DIFFERENTIAL PRESSURE REFUELING
MACHINE
•
Refill or reflux the oil by using the pressure
difference between the two uneven oil
tanks.
•
After refueling, lower the oil tank to
withdraw the extra oil.
•
Capacity: 4L (Can be refilled during use.)
•
Attached with 8pcs adapter set, same as
JTC-4252#D.
UNDERCAR SERIES
JTC-4540 OPEN TYPE STEERING KNUCKLE SPREADER TOOL (SINGLE) JTC-4541 OPEN TYPE STEERING KNUCKLE SPREADER
TOOL (TWIN)
•
Adjustable tool designed for spreading the
steering fixed seat of shock absorbers without
damaging the aluminum or cast-iron knuckle.
•
Made of chrome-moly steel for more strength.
•
Applicable: VAG, BMW, Citroen, FORD, Renault,
Seat, Peugeot and most Japanese vehicles.
•
•
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
Adjustable tool designed for spreading
the steering fixed seat of shock
absorbers without damaging the
aluminum or cast-iron knuckle.
Applicable: Specially designed for twin
ball joints as fitted on VAG control
arms.
Made of Chrome-moly steel for more
strength.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4548 HAND OPERATED GREASE PUMP
•
Capacity: 20L
•
Suitable for 00# ~ 2# grease.
•
Deliver rate: 4cc/press
•
Hose length: 6ft
JTC-4564 BRAKE SHOE GAUGE
•
A time saving tool for measuring the brake pad
lining on the vehicle without removing the wheel.
•
Special slim design for measuring the distance
between the lower side of the backing plate and
brake disc.
•
Designed for both internal and external brake
pads, features a 1.5mm and calibration check
marking.
•
Capable for 6mm backing plate (class IV, V).
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-4640 C.V. JOINT BANDING TOOL (WITH CUTTER)
•
Operated by hand or 1/2" wrench.
•
This tool is easily removed by sliding
sideways after winding has been
completed.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4641 BEARING PACKER
JTC-4642 BALL JOINT SEPARATOR 17mm
JTC-4643 BALL JOINT SEPARATOR 32mm
•
To pack grease into bearing by easily
compressing.
•
For splitting track-rod ends, anti-roll bar
mountings, ball joints, etc.
•
For splitting track-rod ends, anti-roll
bar mountings, ball joints, etc.
•
To add grease from the grease fitting in the
top or removing the body.
Applicable: bearing max. I.D.??16mm and
max O.D.??95mm.
•
A: 17mm
•
A: 32mm
•
MAX. B: 58mm
•
MAX. B: 80mm
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4644 BALL JOINT SEPARATOR 45mm
JTC-4660 2 PCS RUBBER RING HOOK TOOL SET
JTC-4661 BALL JOINT SEPARATOR (HIGH)
•
For splitting track-rod ends, anti-roll bar
mountings, ball joints, etc.
•
Specially designed to pull the rubber ring which
connected with exhaust tube.
•
Adjustable size for your convenient to
fit different vehicle.
•
A: 45mm
•
2 special angle hook attached.
•
Jaw opening: 20mm
•
MAX. B: 90mm
•
Applicable height: 27 ~ 55mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4663 EXHAUST SPRING CLAMP REMOVER /
INSTALLER
•
Distinctive design to hold opening the
spring clamp and replace the exhaust.
•
Total length: 300mm
•
Max. jaws opening: 60mm
•
Applicable: Peugeot, Renault, Citroen, etc.
JTC-4672 INTERNAL BEARING REMOVER SET
•
Two function bearing remover for puller and slide
hammer.
•
Contents:
1 pc Tailpipe expanders (62mm).
1 pc Slide hammer.
5 pcs Puller: 8 ~ 11mm, 12 ~ 17mm, 18 ~ 23mm, 24 ~
29mm, 30 ~ 34mm.
3 pcs extension threads.
•
Applicable: bearing I.D.: 8 ~ 34mm
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-4713 SHOCK ABSORBER RAM DISMANTLE SOCKET
•
To insert this tool in and twist 90° to
pull open the sleeve, and remove the
ram.
•
Applicable: VW, AUDI, SKODA, SEAT,
FORD, BMW, CITROEN, RENAULT, and
PEUGEOT.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4725 SLOTTED SOCKET 24mm
•
•
JTC-4731 10 POINT IMPACT SOCKET 20mm
Distinctive design for removing/installing
the steeling fixing nut on the truck.
•
Size: 1/2" Dr. 4.0 x 24 mm
•
Special designed for the fixing screw on the rear
torque frame of HONDA CR-V.
JTC-4810 TUBE BRAKE OIL FILLER
•
Capacity: 1000 c.c.
•
To hook by front side and fix the oil
can, the middle side is tube of silicon;
the oil can is steadied by magnetic
hook.
•
The gravitation will not be transmitted
to car and causes oil can to break.
•
Available for narrow spaces using as
tube designed.
Size: 1/2" Dr. x 20 mm 10 points
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4817 HUB SLIDE HAMMER PULLER
(OUTSIZE HAMMER)
JTC-4829 SINGLE–WAY BRAKE BLEEDER TUBE
•
•
Extra-large internal hole for European car.
•
Coverage with five oval-shaped holes to
meet assorted sizes of hubs.
•
•
Increasing the power of pulling with both
hands held outsize slide hammer.
•
Hammer weight: 6.3kgs
•
•
Straightforward way to release the remained
brake oil.
Adjustable black rubber adapter for distinct size
nozzle.
With simple screen to show the clear oil and
finish the work.
Capacity: 1000 c.c.
JTC-4855 EXTRA LARGE CUSTOM–BUILT BUSH /
BEARING / SEAL DRIVER SET
•
•
•
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
This extra-large driver set allows you
to build your own custom bushing
driver. Select the required sizes and
assemble your driver tool.
Discs relate to a shaft and screw which
connects to the driver handle.
Build to suit the required seal bush or
bearing job.
Discs size: 70mm through to 150mm in
5mm increments.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4856 CUSTOM BUILT BUSH / BEARING / SEAL DRIVER
SET
•
This master set allows you to build your
own custom bushing driver. Select the
required sizes and assemble your driver
tool.
•
Build to suit the required seal, bush or
bearing job.
•
Disc size: G18mm through to 65mm in
1mm increments and 74mm.
JTC-4868 EXHAUST PIPE HANGER STRETCHER
•
The stretcher removes exhaust rubber-style
hangers easily.
•
The slip-resistant handles and self-locking force
pin allow for quick removal of rubber exhaust
hangers.
•
JTC-4873 HUB PULLER & SEPARATOR
•
Fix the plate on the tire screw thread,
screw the bolt to separate the wheel drive
shaft and hub by pushing.
•
Pick the fit output shaft adapter to meet
central screw, then lock in the
transmission shaft, put the frame on, lock
the nut and fix the screw to pull the wheel
shell close to the drive shaft.
•
Output shaft adaptor: M22 x 1.5, M24 x
1.5, M27 x 1.5, M30 x 1.5
A slim profile and 25° offset allow for easy access
to confined areas.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4880 BRAKE CALLIPER GUIDANCE THREAD REPAIR
SET
JTC-5341 3–JAW INTERNAL BEARING REMOVER SET
•
•
For repairing the guide pen threads in the wheel
bearing housing.
•
With disassembly of guide ping while changing the
brake pads the internal threads are frequently
destroyed.
•
The defective threads are repaired professionally
and quickly with a heavy-duty rust-proof high-grade
steel threaded bush.
•
Contents:
•
Use for removing the internal bearing, sleeve,
and disc.
Range: 13 ~ 38mm
Replacement bushes with copper ring M9 X 1.25 (packing
unit 10 pcs).
Special core drill.
Special tap M9 X 1.25.
Hex key 7mm.
•
Applicable: FORD, OPEL, VW, AUDI.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-5611 TIRE PRESSURE GAUGE
•
Calibrated in 0.2 kgs/cm 2 (20kPa)
increments from 1 to 11kg/cm2(100 ~
1100kPa) and 2.5 lb./in2 from 10 to
160 lb./in2.
•
Chrome-plated and 270mm long.
•
Head I.D. is 8mm.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-5807 EFFORT–SAVING CLOSED EYE TOOL
•
Hook the identity to let the ribbon through
the tire, then to make the needle's way
forward by hand push.
•
Good effort-saving by hook tire to make
the needle's way forward.
•
The needle way is smooth-going, easy to
orientate, will not cause over or less.
JTC-1001A 25 PCS FWD FRONT WHEEL BEARING TOOL
(WITH BEARING)
•
•
A great tool used to replace front wheel bearing
without removing the steering knuckle and strut
assembly.
As the spindle assemble isn`t removed, there is
no need to align front end after the job is done.
•
Fits on most cars.
•
Applicable with hydraulic press.
•
Total: 25 pcs brand new combination.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-1023A PNEUMATIC FLUID EXTRACTOR
•
•
•
Capacity: 8.5 liter
•
•
•
Extract with 3 min for 5-liter engine oil.
•
•
•
Quick and safe.
Work pressure: 90 psi
Simple and easy to operate suitable for
engine oil, gear oil, transmission and
brake fluid water.
Non-spark power oil extractor
Only operate by one man, clear operation.
Save manpower.
Heat-resistance Temperature: 60℃
4 sets / 9kgs / 10kgs / 3.8'
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1142A BEARING SEPARATOR KIT
JTC-1142P EXTRA LONG EXTENTION BAR FOR JTC-1142
JTC-1404A SPRING COMPRESSOR STAND
•
Bearing separator 9015 Included.
•
To use with JTC-1142.
•
•
Pullout the bearing with the H-type beam
and bolts.
•
For removing the bearing between rear drive
shaft and differential.
•
•
Length:640 mm
•
•
•
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
Rotate the steering disc to make it move up-down for quick
operation and labor-saving. Besides, it won't leak oil like hydraulic
type.
Special designed upper jaws to adjust up-down and front-back
direction for fixing the spring tightly, safely, and stable.
The compressor fixed base could hold the cylinder center very
easily and it's very convenient to dismantle.
The lower supporting stand could prevent the shock absorber
from moving downside to make the cylinder to be deformed.
Specially designed for dismantling shock absorber, applicable for
most cars.
Patented.
1.
Rotate gear wheel of the steering disc to drive
the upper jaws in an up-down direction.
2.
The fixing hook was installed inside carrier shim
and the jaw could be adjusted in up-down and
front-back to be at appropriate position for
pressing the spring safely.
3.
Fix cylinder in center position as the lower
stand will support and prevent the cylinder
from being deformed.
4.
Adjust up-down direction to support the shock
absorber for easier operation.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1452A 21 PCS POSITIVE & NEGATIVE CALIPER WIND
BACK KIT
JTC-1532A CV BOOT CLAMP PLIERS (HEAVY DUTY)
JTC-1538A POCKET BRAKE FLUID TESTER
•
•
Two bodies with positive thread and
negative thread for different models.
For assembly of new stainless-steel clamp-bands
on drive-shafts where a torque setting is
required.
The tester can be a digital brake fluid
tester suitable for determining brake
fluid quality.
•
•
Total: 21 pcs.
The 3/8" torque wrench is ideal to provide the
drive.
•
Made from CR-MO material, which is rigid and
durable.
Quality is tested and indicated on five
LEDs in terms of “per cent of water in
the brake fluid”.
•
LED display:
•
More adapters than 1613A for using on
more new model vehicles.
•
•
Green: no water – OK.
Yellow: less than 1% of water. – Warming.
Yellow/yellow: approx. 2% of water. – Warming.
Yellow/yellow/red: approx. 3% of water. The oil
should be changed.
Yellow/yellow/red/red: At least 4% of water.
Change the oil urgently.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-1610A FWD FRONT WHEEL BEARING TOOL
•
•
A great tool used to replace front wheel
bearing without removing the steering
knuckle and strut assembly.
JTC-1613A 15 PCS CALIPER WIND BACK KIT
•
Winds back brake piston for replacing brake
pads.
•
Fits most cars.
As the spindle assemble isn't removed
there is no need to align front end after
the job is done.
JTC-1943A STEERING WHEEL REMOVER / LOCK PLATE
COMPRESSOR SET
•
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
Removing steering wheels of most
vehicles with or without telescoping
tilt steering columns is easy with this
new set.
The steering wheel lock plate
compressor is also included, to
compress the steering wheel lock
plate to remove or install the snap
ring.
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-3922L METAL T HANDLE CLOSED EYE TOOL
•
Durable metal T handle design.
•
Chrome-Molybdenum steel tip.
•
Tip length: 73mm
•
Changeable tip design.
JTC-4144A HAND OPERATED ATF FLUID DISPENSER
•
•
•
•
•
•
•
•
•
Tank capacity: 9.5 liter
JTC-4219A WHEEL STUD ALIGNMENT GUIDE TOOL
•
Assists when mounting wheels,
especially late models with long lug
bolts.
•
Applicable: all Mercedes models with
lug bolts.
•
Size:
Flow capacity: 75 cc/cycle
Hose size: 3/8" x 1500mm.
Size: 330x 260x 650mm.
Special designed for filling ATF oil.
Replaceable fittings for different vehicles.
With hand pump for vacuum to prevent oil deterioration.
Weight: 3.5kg
Contains 8 fittings.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
2 - M12 x 1.25
2 - M12 x 1.5
2 - M14 x 1.25
2 - M14 x 1.5
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-4920S HUB SLIDE HAMMER SET
JTC-F0412 BALL JOINT SEPARATOR 24mm
JTC-F0416 THIN BALL JOINT SEPARATOR 18mm
•
With 4 holes and 5 holes for all the
vehicles.
•
Tempered drop forged steel one-piece
construction for long & rough usage.
•
Tempered drop forged steel one-piece
construction for long & rough usage.
•
Increasing the power of pulling with both
hands held outsize slide hammer.
Hammer weight:6.3 kgs
•
15/16" (24mm) Fork, 11-7/8" (300mm) length
replace worn out ball joint easily with a hammer
striking.
•
21/32" (18mm) Fork, 16"(410mm)
length replace worn out tie rods easily
with a hammer striking.
•
Can remove CV drive shafts on FWD vehicles.
•
Can separate shock absorber links.
•
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-F1954 BALL JOINT SEPARATOR
•
Heat treated drop forged steel body & bolt
for long rough usage.
•
Spread ball joints easily where space
prevents use of direct method.
Jaw open: 19mm.
•
JTC-F270 DROP FORGED COIL SPRING COMPRESSOR
•
•
Drop forged CR-V steel jaws and leaded screws
(270mm) both heat treated ensure you obtain
professional job performance.
The tool is designed for use in limited space
under wheel arch.
•
Jaw design is fitting to warp coil claws for safely.
•
Maximum jaw opening is 270mm.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024
JTC-F370 DROP FORGED COIL SPRING COMPRESSOR
•
Heat treated drop forged CR-V steel
jaws & leaded screws (270mm)
•
The tool is designed for use in limited
space under wheel arch.
Distinct design claws to warp on coil
spring safely.
Maximum jaw opening is 270mm.
•
•
JTC AUTO TOOLS USA
UNDERCAR SERIES
JTC-J01 DISC BRAKE PISTON SEPARATOR
•
Fits in brake caliper to push back pistons
for new brake pads installation.
•
Patented.
JTC AUTO TOOLS USA
678 – 876 – 3470
2600 NORTHLAKE DR., SUITE F,
SUWANEE, GA, 30024