Plug-in Maxi ISO Relays
Power Relay F7
nPin
assignment similar to ISO 7588 part 1
versions on request
– 24VDC versions with contact gap >0.8mm
– Integrated components (e.g. resistor, diode)
– Customized marking/color
– Special covers (e.g. notches, release features, brackets)
nCustomized
Typical applications
Cross carline up to 70A for example: ABS control, cooling fan, energy
management, engine control, glow plug, heated front screen, ignition,
lamps: front, rear, fog light, main switch/supply relay.
F134J_a_bw
Contact Data
Contact arrangement
1 form A,
1 form A,
1 form A,
1 NO
1 NO
1 NO
Contact gap
-
-
>0.8mm
Rated voltage
12VDC
24VDC
24VDC1)
Limiting continuous current
23°C
70A
70A
70A
85°C
50A
50A
50A
125°C
30A
30A
30A
Limiting making current2)
240A240A240A
Limiting breaking current
70A
25A
40A
Limiting short-time current
3)
overload current, ISO 8820-3 1.35 x 50A, 1800s
2.00 x 50A, 5s
3.50 x 50A, 0.5s
6.00 x 50A, 0.2s
Jump start test, ISO 16750-1
24VDC for 5min,
conducting nominal current at 23°C
Contact material
Silver based
Min. recommended contact load4)
1A at 5VDC
Initial voltage drop,
form A (NO) contact at 10A, typ./max.
10/300mV
Frequency of operation at nominal load
6 ops./min (0.1Hz)
Operate/release time typ.
7/2ms5)
Electrical endurance
resistive load at 14VDC
>1x105 ops.
-
70A
>2x105 ops. -
50A
resistive load at 28VDC
-
>1x105ops.>1x105 ops.
25A 50A
Max. DC load breaking capacity
Contact Data (continued)
Mechanical endurance
>1x107ops.
1) Special high performance 24VDC version with contact gap >0.8mm, part number
V23134-A0056-X408 (see part number table).
2) The values apply to a resistive or inductive load with suitable spark suppression and
at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current
duration of maximum 3s for a make/break ratio of 1:10.
3) Current and time are compatible with circuit protection by a typical automotive fuse.
Relay will make, carry and break the specified current.
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay
coil increases the release time and reduces the lifetime caused by increased erosion
and/or higher risk of contact tack welding.
Coil Data
Rated coil voltage
12VDC, 24VDC
Coil versions, DC coil
Coil
Rated
Operate
Release
Coil
Rated coil
codevoltagevoltagevoltage
resistance6)power6)
VDCVDCVDC
Ω±10%W
05212 7.21.690 1.6
0532414.4 3.2324 1.8
0562416.0 4.0268 2.1
0652414.4 2.4288 2.0
6) Without components in parallel.
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Coil operating range
TEVF4_OVR1
ECR0629-N
Does not tak
the temperat
the contact c
E = pre-ener
Load limit curve: safe shutdown, no stationary arc/make contact.
Load limit curve measured with low inductive resistors verified for 1000 switching events.
04-2013, Rev. 0413
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Does not take into account the temperature rise due to the contact current
E = pre-energization.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog, product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
1
Plug-in Maxi ISO Relays
Power Relay F7 (Continued)
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
between adjacent contacts
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
500Vrms
500Vrms
500Vrms
Vs=+86.5VDC
Vs=+200VDC
Other Data
EU RoHS/ELV compliance
compliant
Protection to heat and fire according UL-94
HB or better7)
Ambient temperature
-40 to 125°C
Climatic cycling with condensation
EN ISO 6988
6 cycles, storage 8/16h
Temperature cycling,
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant, IEC 60068-2-3, Ca
56 days
Category of environmental protection,
IEC 61810 RTI – dustproof, RT III – sealed
Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed)
Corrosive gas
IEC 60068-2-42 10±2cm3/m3 SO2, 10 days
IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep)
10 to 500Hz, min. 5g8)
Shock resistance (functional)
IEC 60068-2-27 (half sine)
6ms, min. 30g.8)
Drop test, free fall
IEC 60068-2-32
1m onto concrete
Other Data (continued)
Terminal type
Cover retention
axial force
pull force
push force
Terminal retention
pull force
push force
resistance to bending
force applied to side
torque
Weight
Resistance to soldering heat THT
IEC 60068-2-20
Packaging unit
plug-in:
plug-in with bracket:
PCB
plug-in, QC/ PCB
150N
150N
150N
100N
100N
10N8)
10N8)
0.3Nm
approx. 38g (1.3oz)
260°C, 10s
210 pcs.
208 pcs.
315 pcs.
7) Refers to used materials.
8) No change in the switching state >1μs. Valid for NC contacts, NO contact values significantly higher.
8) Values apply 2mm from the end of the terminal. When the force is removed, the terminal
must not have moved by more than 0.3mm.
Accessories
For details see datasheet Connectors for Maxi ISO Relays
Terminal Assignment
NO
1 form A, NO
2
NOR
1 form A, NO with resistor
NOD
1 form A, NO with diode
85
87
85
87
85
87
86
30
86
30
86
30
04-2013, Rev. 0413
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Plug-in Maxi ISO Relays
Power Relay F7 (Continued)
Dimensions
Power Relay F7 with quick connect terminals
View of the terminals (bottom view)
25.9 ±0.3
TE1103-411
15 ±0.1
6 ±0.4
4 ±0.2
5.3 ±0.1
25.9 ±0.3
16 ±0.5
24.9 ±0.3
Measurement
reference plane
4x
0.3
11 ±0.5
17 +1/-0.5
26.2 MAX.
26.2 MAX.
ø 1.7 +0.2
6.3 ±0.1
25.2 MAX.
0.8 ±0.05
9.5 ±0.1
1.2 ±0.05
Quick connect terminal similar to ISO 8092-1
3.0
TE1098-Y1
1.5
TE2104-H1
TIN PLATED
Power Relay F7 with PCB terminals
3.8 view)
View of the terminals (bottom
26.2 MAX.
26.2 MAX.
30
86
85
2.7
87
25.2 MAX.
3.0
1.5
TIN PLATED
TE2104-H1
3.8
PCB Layout
Bottom view on solder pins
30
3.8
86
85
3.8
2.7
87
2x 2.18
17.9
8.4
TE2105-Q1
3.8
8.5
2x 1.93
3.8
17.0
04-2013, Rev. 0413
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog, product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
3
Plug-in Maxi ISO Relays
Power Relay F7 (Continued)
Product code structure
Typical product code V23134 -J
Type
V23134 Power Relay F
Contact arrangement
J
1 form A, 1 NO
Cover
0
Standard
Coil
052 12VDC
056 24VDC (contact gap >0.8mm)
Terminal/arrangement
D642 Plug-in/NO
1
Bracket near terminal 30 ISO
053
065
24VDC
24VDC
0
052-D642
Xnnn Customized (nnn: version number)
Product code
V23134-J0052-D642
V23134-J0052-X429
V23134-J0052-X439
V23134-J0052-X455
V23134-J0052-X511
V23134-J0052-X461
V23134-J0053-D642
V23134-J0056-X4082)
V23134-J0065-X4974)
V23134-J1052-D642
V23134-J1052-X281
V23134-J1053-D642
Arrangement Cover
1 form A, 1 NO
Standard
Coil suppr.
Resistor 680Ω
Diode (cathode 86)
Resistor 470Ω
Resistor 560Ω
Resistor 1200Ω
Bracket
Resistor 560Ω
Circuit1)
NO
NOR
NOD
NOR
NO
NOR
NO
NOR
NO
NOR
NO
Coil
12VDC
04-2013, Rev. 0413
www.te.com
© 2013 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Silver based
Plug-in, QC
PCB
Plug-in, QC3)
Plug-in, QC
Plug-in, QC3)
PCB
Plug-in, QC
24VDC
12VDC
24VDC
1) See terminal assignment diagrams.
2) Special feature: contact gap >0.8mm.
3) Special feature: 14.5mm load terminals.
4) Packed in tray with 300 pcs. per unit.
Other types on request.
This list represents the most common types and does not show all variants covered by this datasheet.
4
Cont. material Terminals
Part number
7-1393303-3
1-1414147-0
1-1414286-0
1-1414610-0
3-1415001-2
1-1414469-0
9-1393303-7
0-1393304-5
3-1414937-3
0-1393304-9
1-1393304-0
1-1393304-1
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Download PDF