Memory Module Specifications
KHX16C9K4/32X
32GB (8GB 1G x 64-Bit x 4 pcs.)
DDR3-1600 CL9 240-Pin DIMM Kit
SPECIFICATIONS
CL(IDD)
9 cycles
Row Cycle Time (tRCmin)
49.5ns (min.)
Refresh to Active/Refresh
Command Time (tRFCmin)
260ns (min.)
Row Active Time (tRASmin)
36ns (min.)
Maximum Operating Power
2.460 W* (per module)
UL Rating
94 V - 0
Operating Temperature
0o C to 85o C
Storage Temperature
-55o C to +100o C
*Power will vary depending on the SDRAM used.
DESCRIPTION
FEATURES
Kingston's KHX16C9K4/32X is a kit of four 1G x 64-bit (8GB)
DDR3-1600 CL9 SDRAM (Synchronous DRAM) 2Rx8 memory
•
•
•
•
•
•
•
•
•
•
JEDEC standard 1.5V (1.425V ~ 1.575V) Power Supply
•
•
Bi-directional Differential Data Strobe
•
•
On Die Termination using ODT pin
•
•
Asynchronous Reset
modules, based on sixteen 512M x 8-bit DDR3 FBGA components per module. Each module kit supports Intel ® XMP
(Extreme Memory Profiles). Total kit capacity is 32GB. Each
module kit has been tested to run at DDR3-1600 at a low
latency timing of 9-9-9 at 1.5V. The SPDs are programmed to
JEDEC standard latency DDR3-1333 timing of 9-9-9 at 1.5V.
Each 240-pin DIMM uses gold contact fingers and requires
+1.5V. The JEDEC standard electrical and mechanical specifications are as follows:
XMP TIMING PARAMETERS
•
•
JEDEC: DDR3-1333 CL9-9-9 @1.5V
XMP Profile #1: D3-1600 CL9-9-9 @1.5V
VDDQ = 1.5V (1.425V ~ 1.575V)
667MHz fCK for 1333Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 9, 8, 7, 6
Posted CAS
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
PCB : Height 1.18” (30mm) double sided component
Continued >>
Document No. 4806444-001.B00
12/18/12
Page 1
continued
HyperX
MODULE DIMENSIONS
T E C H N O L O G Y
133.35
Units: millimeters
30.00
18.80
15.80
11.00
8.00
54.70
0.00
0.00
MODULE WITH HEAT SPREADER
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
Document No. 4806444-001.B00
Page 2
Download PDF