Whirlpool | HB 0705 AX0 UK | Instruction for Use | EN Operating Instructions

1
HB 0701 AX0 UK HB 0703 AX0 UK HB 0705 AX0 UK
2
3
4
13
8
12
16
11
14
9
15
9
8
19
18
17
17
11
10
14
7
5
15
7
18
12
6
6
19
Indesit Company UK Ltd
Morley Way,
Peterborough PE2 9JB
www.indesitcompany.com
HB 07 UK
02/2013 - ver.1.1
5
16
13
EN
Operating Instructions
220-240V
700W
HB 07 UK
A
B
C
D
E
en
PARTS AND FEATURES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Speed-adjusting dial
ON/OFF button
Turbo button
Motor unit
Blender attachment
Beaker (only on some models)
Whisk attachment (only on some models)
Food pusher (only on some models)
Storage unit (only on some models)
Big bowl lid (only on some models)
Feed tube (only on some models)
Big chopper blade (only on some models)
Big bowl (only on some models)
Shredding/slicing disc (fine) (only on some models)
Shredding /slicing disc (coarse/thick) (only on some models)
Disc shaft (only on some models)
Small bowl lid (only on some models)
Small chopper blade (only on some models)
Small bowl (only on some models)
INTRODUCTION
Thank you for purchasing our product. In doing so, you have opted for an effective high-performance
appliance.
These operating instructions refer to various models. An overview of the different models can be found
on the illustrated pages.
If the instructions on the correct use of this appliance are not observed, the manufacturer shall assume
no responsibility for any resulting damage. The operating instructions may describe different models:
any difference is clearly identified.
5
en
IMPORTANT INFORMATION
ON SAFETY
Before using the electrical appliance, always
follow basic safety precautions, including the
following:
1. Read all the instructions.
2. Save these instructions.
3. Before using it, check that the voltage of the
wall outlet corresponds to the voltage shown
on the rating plate.
4. Do not operate any appliance with a damaged
cord / plug. If the appliance malfunctions or
is dropped or damaged in any manner return
the appliance to the nearest authorised
service facility for examination, repairs or
electrical / mechanical adjustment.
5. If the supply cord is damaged, have it
replaced by the manufacturer, an authorised
service agent or a qualified technician in
order to avoid hazards.
6. Unplug it from the outlet when not in use,
before installing / removing any parts and
before cleaning it.
7. Do not let the cord hang over the edge of
a table / counter or touch any hot surfaces.
8. Do not immerse the motor unit of the blender
in water, as this would give rise to electric
shocks.
9. Avoid contacting moving parts.
10. Keep your hands and utensils out of the
container while blending to reduce the risk
of severe injury to persons or damage to the
blender. A scraper may be used when the
food processor is not running.
11. To avoid blunting the blade, do not use on
dry or hard substances
12. Make sure the lids are securely locked in
place before operating the appliance.
13. The use of accessory attachments
not recommended by the appliance
manufacturer may cause injuries or damage.
14. Do not operate the appliance for anything
other than its intended use.
15. Never insert food by hand. Always use the
food pusher.
16. Before disassembling the appliance, switch
off the unit and wait until the blades have
come to a complete stop.
6
17. Always remove the blade assembly before
pouring any contents from the bowl.
18. Be sure to switch off the appliance after
each use of your food processor. Make
sure the motor stops completely before
disassembling.
19. Do not put your fingers or other objects into
the unit opening while it is in operation. If any
food gets stuck in the opening, use the food
pusher or another piece of fruit / vegetable
to push it down. When this method is not
possible, turn the motor off and disassemble
the unit to remove the remaining food.
20. Do not attempt to tamper with the lid interlock
mechanism.
21. The metal blades and disc are extremely
sharp: handle with care. Always hold the
blade attachments away from the cutting
edges, both when handling and cleaning the
unit.
22. Do not use outdoors.
23. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been provided supervision or
instructions on the use of the appliance by a
person responsible for their safety.
24. Children should be supervised to ensure that
they do not play with the appliance.
25. This appliance is intended to be used for
household and similar applications such as:
• staff kitchen areas in shops, offices and
other working environments;
• farm houses;
• by clients in hotels, motels and other
residential-type environments;
• bed&breakfast-type environments.
26. Always make sure that the appliance is in
good working order and that all its removable
parts are secure. Regularly check the power
supply cord and plug for cuts or damage.
27. Be sure your hands are completely dry
before touching the switch.
BEFORE FIRST USE
Carefully wipe the outside of the appliance to
remove any dust that may have accumulated.
Dust with a dry cloth. Do not immerse the supply
en
immediately. For maximum-speed whisking
use the TURBO button for a short time.
cord in water or other liquids.
Blades and discs are very sharp: handle
with care.
The speed adjusting dial cannot be used
with the TURBO button.
USING YOUR BLENDER (A)
Max operation at high speed each time
shall not last longer than 30 seconds.
The blender attachment is suitable for blending
juices and vegetables.
1.
2.
3.
4.
To assemble the blender attachment to the
motor unit, turn the stem clockwise until
tightened.
Peel or core the fruits and then cut them into
small pieces. Then put the fruit pieces or
vegetables into the beaker. Usually a certain
amount of water has to be added to facilitate
smooth running, the proportion of food and
water being 2:3. The mixture amount should
not exceed the max capacity of the cup.
Plug the appliance into the power outlet.
Lower the hand blender into the food and
rotate the speed-adjusting dial to select the
desired speed. Pressing and holding the
ON/OFF button, the blender starts blending
immediately. For maximum-speed blending
use the TURBO button for a short time.
Instead of the beaker, you can use any
kitchen container with a suitable shape.
USE THE SMALL BOWL FOR FINE
CHOPPING (only on some models)
(C)
1.
2.
3.
A small amount of water can facilitate
the smooth running of the appliance.
The mixture amount should not exceed
the max capacity of the bowl.
The speed-adjusting dial is not suitable
for the TURBO button.
Max operation at high speed each time
shall not last longer than 30 seconds.
Instead of the beaker, you can use any
kitchen container with a suitable shape.
USE THE WHISK ATTACHMENT (only
on some models) (B)
Max operation at high speed each time
shall not last longer than 30 seconds.
4.
5.
6.
7.
The whisk attachment is mainly suitable for
whisking egg whites.
1.
2.
3.
4.
To assemble the whisk attachment to the
motor unit, turn the stem clockwise until
tightened.
Place the food into the beaker.
Plug the appliance into the power outlet.
Lower the whisk into the food and rotate the
speed-adjusting dial to select the desired
speed. Pressing and holding the ON/OFF
button, the attachment starts whisking
First of all make sure the non-slip ring is
fixed to the bottom of the bowl.
Fit the knife blade on the pin in the bowl always fit the knife blade before adding the
ingredients.
Cut the food into small pieces and put them
into the bowl.
Close with the lid.
Assemble the motor unit into the bowl lid and
turn it clockwise to lock them.
Plug the appliance into the power outlet.
Rotate the speed-adjusting dial to select the
desired speed. Pressing and holding the ON/
OFF button, the attachment starts chopping
immediately. For maximum speed press the
TURBO button for a short time.
The speed adjusting dial cannot be used
with the TURBO button.
Never remove the lid until the blade has
come to a complete stop.
8.
Remove the knife blade first before pouring
out the mixture.
The knife blade is very sharp: take care
when handling. Max operation at high
7
en
speed each time shall not last longer than 30
seconds.
8.
The knife blade is very sharp: take care
when handling.
USING THE FOOD
PROCESSOR ATTACHMENT
Max operation at high speed each time
shall not last longer than 30s.
To use the chopping bowl (only on some models):
1.
2.
3.
First of all make sure the non-slip ring is
fixed to the bottom of the bowl.
Fit the knife blade on the pin in the bowl always fit the knife blade before adding the
ingredients.
Cut the food into small pieces and put them
into the bowl.
Using the bowl and shredding/slicing discs for processing (only on
some models) (E).
1.
The mixture amount should not exceed
the max capacity of the bowl.
First of all make sure the non-slip base is
fixed to the bottom of the bowl.
Then insert the disc shaft into the pin on
the bottom of the bowl, select the desired
shredding/slicing disc (fine or coarse) and
assemble the shredding /slicing disc onto
the shaft with the appropriate side upwards
(one side is for shredding, the other side is
for slicing).
Max operation at high speed each time
shall not last longer than 30 seconds.
Extreme caution must be taken when
handling discs as they are very sharp.
Align the two fasteners of the bowl lid with
the two clip positions of the bowl and push
down to lock them in place. Be sure to align
the arrow on the lid and the arrow on the
bowl.
Pull the two fasteners towards the outside to fit
the lid onto the bowl, making sure the lid arrow is
aligned with the bowl arrow.
2.
A small amount of water can facilitate
the smooth running of the appliance.
4.
The fasteners must be locked in the two
clip
positions,
otherwise
during
operating the bowl lid may rotate as the motor
rotates.
Make sure the food pusher is properly
fitted into its housing on the cover.
5.
6.
7.
8
Remove the knife blade first before pouring
out the mixture.
Assemble the motor unit into the bowl lid and
turn it clockwise to lock them.
Plug the appliance into the power outlet.
Rotate the speed-adjusting dial to select the
desired speed. Pressing and holding the ON/
OFF button, the attachment starts chopping
immediately. For maximum speed press the
TURBO button for a short time.
The fasteners must be locked in the two
clip
positions,
otherwise
during
operating the bowl lid may rotate as the motor
rotates.
3.
4.
5.
6.
Insert the bottom part of the motor unit
into the opening on the bowl lid, and turn it
clockwise to lock.
Plug the appliance into the power outlet.
Put the food inside the feeding tube and
push it slowly with the food pusher. Do not
push heavily.
Rotate the speed-adjusting dial to select the
desired speed. Pressing and holding the ON/
OFF button, the attachment starts chopping
immediately. For maximum speed press the
TURBO button for a short time.
The speed adjusting dial cannot be used
with the TURBO button.
The speed adjusting dial cannot be used
with the TURBO button.
Never remove the lid until the blade has
come to a complete stop.
Never remove the lid until the cutting
disc has come to a complete stop.
en
Never introduce very hard foods (e.g.
hard chocolate), ice or frozen foods
when using shredding or slicing attachments.
immerse it in water for cleaning purposes, as
electric shocks may occur.
The non-slip base on the bottom of the bowl
can be removed and cleaned. Make sure it
is re-placed correctly before using it again.
Dry all detachable parts thoroughly.
4.
TIPS
•
•
•
•
Use the shredding side for carrots, potatoes
and foods of a similar texture.
Use the slicing side for food items such as
carrots, potatoes, cabbages, cucumbers,
courgettes and onions.
Use fresh ingredients.
Do not cut food too small. Fill the feed
tube uniformly. This prevents the food from
pouring out during processing.
5.
Blades are very sharp: handle with care.
TIP
STORAGE SYSTEM (F)
For quick cleaning between processing tasks, fill
the cup or bowl with water halfway, assemble the
hand-held blender according to the description
in the operation section and start the blending /
chopping function for a few seconds.
When not in use, the detachable stem, whisk and
motor unit can be stored on the bowl lid.
GUARANTEE
When placing the discs inside the bowl
for storage, make sure the cutting edges
do not scratch the bowl walls.
CLEANING AND
MAINTENANCE
To prevent any damage to the appliance
do not use harsh solvents or abrasive
cleansers when cleaning.
Unplug the appliance from the power supply
before cleaning.
1.
Wash the blender attachments and lids
under running water without any abrasive
cleaners or detergents. After cleaning, place
them upright so that any water that may
have got in can drain out.
Do not immerse the blender and lids in
water, as the lubrication on the bearings
may be washed away over time.
2.
3.
Wash the containers and whisk in warm
soapy water. All removable parts can be
washed in warm soapy water and then
carefully rinsed and dried. If necessary, use
a nylon-bristle brush to complete the cup
cleaning operation.
Wipe the motor unit with a damp cloth. Never
12 months Parts and Labour Guarantee
This certificate of guarantee represents the guarantee (“Guarantee” hereinafter) offered by Indesit Company UK Limited with registered office
at Peterborough PE2 9JB in relation to products
purchased in the United Kingdom and Indesit
Ireland Limited with registered office in Dublin 9,
Ireland for products purchased in the Republic of
Ireland. This Guarantee does not affect your statutory rights.
Your product has the benefit of our manufacturer’s Guarantee, which covers the product for
twelve months from the date of purchase.
This gives you the reassurance that if, within that
time, your product is proven to be defective because of either workmanship or materials, we will,
at our discretion, either repair or replace the product at no cost to you.
This Guarantee is subject to the following conditions:
•
•
•
•
Documentary proof of original purchase date
is provided.
Cosmetic damage must be reported within
14 days from the date of purchase.
The product has been installed and operated
correctly and in accordance with our operating and maintenance instructions.
The product is used only on the electricity
9
en
•
•
•
•
•
supply printed on the rating plate.
The product has been used for normal domestic purposes only.
The product has not been altered, serviced,
maintained, dismantled, or otherwise interfered with by any person not authorised by us.
Any repair work must be undertaken by us or
our appointed agent.
Any parts removed during repair work or any
product that is replaced become our property.
The product is used in the United Kingdom
or Republic of Ireland.
The Guarantee does not cover:
•
•
•
•
•
Damage resulting from transportation, improper use, neglect or interference or as a
result of improper installation.
Accidental damage, this includes but is not
limited to, damage which occurs as a result
of an external action.
Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, light bulbs, hoses, brushes,
covers and filters.
Replacement of any removable parts made
of glass or plastic.
After Sales Service
No one is better placed to care for your Hotpoint
product during the course of its working life than
us – the manufacturer.
Essential Contact Information
Advice Line
We have a dedicated team who can provide free
advice and assistance with your product if you
experience any technical difficulties. Simply call
our Hotpoint Service Hotline on 08448 240 055
(Republic of Ireland 0818 904 041) for telephone
assistance.
Please note:
Our advisors will require the following information:
Model number:
Serial number:
10
Consumables and Accessories
We supply a full range of consumables and accessories to keep your product functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.hotpoint.co.uk
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to
helping the environment, Hotpoint reserves the
right to use quality, recycled components to keep
down customer costs and minimise material wastage.
Please dispose of packaging and old products
carefully.
Register your new product and get a second
year FREE!
We want to give you additional benefits of ownership of your product and offer you an additional
free 1 year guarantee when you register your
product with Hotpoint within 28 days of purchase.
If you do not register your product with Hotpoint
within 28 days, your product is guaranteed for 1
year only.
To activate your 2 year guarantee register with
us online at www.hotpoint.co.uk. Please note that
the 2 year guarantee is only available in UK and
Ireland and is subject to the same conditions as
the 1 year Guarantee. Please refer to the certificate of guarantee for more information.
en
DISPOSAL OF OLD
ELECTRICAL APPLIANCES
The European Directive 2002/96/EC on
Waste
Electrical
and
Electronic
Equipment (WEEE), requires that old
household electrical appliances must
not be disposed of in the normal unsorted municipal waste stream.
Old appliances must be collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected. Consumers should contact their local
authority or retailer for information concerning the
correct disposal of their old appliance.
11
Download PDF

advertising