MASTER OWNER`S GUIDE - Solace Remote Starters

MASTER OWNER`S GUIDE - Solace Remote Starters
MASTER OWNER’S G UIDE
Revision 5.01
01 - 2018
1
CONTENTS
TABLE OF CONTENTS
Safety Notes
3
Warranty4
The Evolution of Auto-Connectivity™
6
Remote Function Legend
7
Remote Function Chart
9
2-Way LCD Remote Features
11
Status Request
11
Entering Function Menu 11
Setting Clock & Precise Remote Start
11
Setting Remote Features
12
Basic Vehicle Commands
12
Lock12
Unlock12
Driver’s Priority Unlock
13
Trunk Release
13
Start13
Idle Mode
13
Turbo Timer
13
Silent Lock/Unlock
14
Aux 1 - 4
14
Car Finder
14
Panic Mode
14
2
Ready Mode Sequence
Valet Service Mode
Alarm Features
Transmitter Learning
Battery Replacement
Remote Sleep Mode
Eco-run Technology
14
17
18
19
19
20
20
IMPOR TANT SAFE T Y NOTES
Carbon Monoxide Poisoning:
The owner/user MUST INSTALL a CARBON MONOXIDE DETECTOR in the living area near to where the vehicle is
being stored or parked. It is the sole responsibility of the owner/user to keep the remote transmitters away from the
reach of children and handle with care so that the system does not unintentionally start. When the vehicle is parked
in an enclosed/partially enclosed area (for example: a garage or car port), being serviced, or if the vehicle is loaned
to an operator not familiar with a remote starter, the system MUST BE placed in Service (Valet) Mode.
N E VER OPE R ATE T HE S YS T EM IN A N ENC LO S ED/ PA R T I A L LY E N C LO SE D A R E A !
Hybrid Remote Starters for Automatic & Manual Transmissions:
The installation of a remote starter MUST BE DONE ONLY with a specified remote starter. Hybrid Remote Starters
have both an automatic transmission and manual transmission mode. It is the responsibility of the vehicle’s operator
to ensure that:
(a) when the remote starter is in use with a vehicle equipped with a manual transmission, the transmission
remains in the NEUTRAL POSITION ONLY.
(b) when the remote starter is in use with a vehicle equipped with an automatic transmission, the
transmission remains in the PARK POSITION ONLY.
It is the sole responsibility of the operator of the vehicle to insure the transmission positions described herein are
maintained at any time the remote starter is in use. In no case shall the manufacturer or Solace be liable for any
damages of any kind whatsoever including but not limited to damages for personal injury or loss of life arising by
virtue of a remote starter being used when the transmission of the vehicle in question is not set as mandated herein.
3
WARR ANT Y
Solace Technologies Ltd. (“Solace”) promises to the
original purchaser to repair or replace (at Solace’s
discretion) with a comparable reconditioned model any
Solace unit (hereafter the “unit”), excluding without
limitation the siren, the remote transmitters, antennas,
the associated sensors and accessories, which proves
to be defective in workmanship or material under
reasonable use during the lifetime of the vehicle
provided the following conditions are met: the unit was
purchased from an authorized Solace dealer, the unit
was professionally installed and serviced by an
authorized Solace dealer; the unit will be professionally
re-installed in the vehicle in which it was originally
installed by an authorized Solace dealer; and the unit is
returned to Solace, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase
bearing the following information: consumer’s name,
telephone number and address; the authorized dealers
name, telephone number and address; complete
product description, including accessories and the year,
make and model of the vehicle.
accessory part for a one-year period from date of
purchase. Accessories will only be replaced if proven
defective in material or workmanship, and if, when the
accessory is returned to the point of purchase, the
retailer is provided with a copy of the proof of purchase.
the “fine print”
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE
THE SOLE LIABILITY OF SOLACE FOR OUR PRODUCTS,
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED. THERE ARE NO WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO PERSON, FIRM OR CORPORATION IS
AUTHORIZED TO ASSUME FOR SOLACE ANY OTHER
LIABILITY WITH RESPECT TO THE SALE OR USE OF OUR
PRODUCTS. SOLACE’S LIABILITY, WHETHER BASED ON
CONTRACT, TORT, AND WARRANTY, STRICT LIABILITY, OR
ANY OTHER THEORY, SHALL NOT EXCEED THE PRICE OF
THE INDIVIDUAL UNIT WHOSE DEFECT FOR DAMAGE IS
THE BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE
WILL SOLACE, ITS DISTRIBUTORS OR THEIR AGENTS
BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
ACCESSORIES
Solace warrants to the original consumer purchaser only
(non-transferable) that it will replace any Solace
4
MORE INFORMATION
http://solaceremotestarters.com/manuals.php
FCC Notice
This device complies with Part 15 of the FCC rules.
Operation of this device is subject to the following
conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
(3) CAUTION: Changes or modifications not
expressly approved by the part responsible for
compliance void the user’s authority to operate this
device.
5
The Evolution of Auto - Connec tivit y ™
The Solace remote starter is an advanced remote vehicle starter. This system has the most innovative features and
customization available of any brand on the market today. It has state-of-the-art protection circuits that will never
leave a customer stranded. This remote start system will work on most vehicles (extra parts may be required). We
use only the most powerful and dependable components available.
All of our remotes have a “family feel” and incorporate OEM-like quality and appearance. All features will be easily
accessible from the remote, with full control of all functions the remote starter controls on the vehicle.
All of our units are compatible with GPS and Smartphone application modules which will allow all features to be
controlled by a smartphone (iPhone, Blackberry, and Android) (extra parts are required).
Solace has been engineered, designed and tested in Edmonton, Alberta, Canada in some of the most extreme
climate conditions. Whether it is warming up your car in the freezing cold of winter, or cooling it down in the heat of
the summer, you can rely on Solace to work for you.
6
TR ANSMIT TER OPER ATION
Remote Functions / Button Layout
The following is a summary of the buttons used to control basic functions of the remote starters.
4-Button
1-Way LED Remote
Lock / Button 1
Unlock / Button 2
Start/Stop / Button 3
2-Button
1-Way Remote
(Programming Dependent)
Lock/Unlock / Button 1
Start/Stop / Button 2
Function / Button 4
4-Button
1-Way LED Remote
Lock / Button 1
1-Button
1-Way Remote
(Programming Dependent)
Start/Stop / Button 1
Unlock / Button 2
Start/Stop / Button 3
Function / Button 4
7
TR ANSMIT TER OPER ATION
Remote Functions / Button Layout / LCD Icons
4-Button
2-Way LED Remote (S2)
4-Button
2-Way LCD Remote (S3 / SA3)
Located on side of remote
Lock / Button 1
Lock / Button 1
Unlock / Button 2
Unlock / Button 2
Start/Stop / Button 3
Start/Stop / Button 3
Function / Button 4
Function / Button 4
Lock Unlock
Car Mode
Range Indicator
1-Button
2-Way LED Remote (S2-1B)
Multi-Function Button
Lock - Press 1x
Unlock - Press 2x (within 1 Sec.)
Start / Stop Press & Hold (2.5 Sec.)
Trunk Release Press 1x then Press & Hold (2.5 Sec.)
Battery Life
Text Info
Alarm
Cold Start
Valet Mode
Ready Mode Set
8
Precise Time Start
Shock Sensor
The following is a summary of the buttons used to control basic functions of the remote starters.
REMOTE FUNC TIONS
COMMAND
Lock/Arm
Unlock/Disarm
Silent Lock/Unlock
Trunk Release
Start
Extend Run Time or Idle Mode
(with Engine Running)
Remote Shutdown
Turbo Mode Remote Activation
(with Engine Running)
Status Request
Temperature Status Request
Voltage Status Request
1 BUTTON
1-WAY / 2-WAY LED
2-WAY LCD
FUNCTION
BUTTON 1
BUTTON 1
Lock doors & arm alarm
system
BUTTON 2
BUTTON 2
Unlock doors & disarm
alarm system
N/A
BUTTONS 1 AND 2
TOGERTER
BUTTONS 1 AND 2
TOGERTER
Silently lock/unlock, arm/
disarm vehicle
N/A
BUTTON 4 (HOLD 2 SECS.)
N/A
BUTTON 2 (HOLD 2 SECS.)
BUTTON 2 (HOLD 2 SECS.)
Opens Trunk
(may unlock doors)
BUTTON 3
BUTTON 3
Remote start vehicle
BUTTON 3
BUTTON 3
Extends runtime by 10
minutes
BUTTON 3 (HOLD 2 SECS.)
BUTTON 3 (HOLD 2 SECS.)
Remote stop the vehicle
while running
BUTTON 4
BUTTON 4
Activates turbo timer
countdown
BUTTON 4 (2-WAY ONLY)
BUTTON 4
Displays status of vehicle
N/A
BUTTON 4 (3X)
Displays ambient interior
temperature of vehicle
N/A
BUTTON 4 (4X)
Displays the voltage of
the vehicle’s battery
2 BUTTON
BUTTON 1 ( HOLD 2 SECS.)
BUTTON 1
BUTTON 1 (TWICE)
BUTTON 1
N/A
BUTTON 1
BUTTON 2
BUTTON 1
BUTTON 2
BUTTON 1 ( HOLD 2 SECS.)
BUTTON 2 ( HOLD 2 SECS.)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
OR
9
REMOTE FUNC TIONS (advanced)
COMMAND
10
1-WAY/2-WAY LED
2-WAY LCD
FUNCTION
Car Finder
BUTTONS 3 & 4
FUNCTION MENU
(HOLD BUTTON 4 FOR 2.5
SECONDS)
Activates siren/horn on vehicle and flashes park lights
for 5 seconds
Panic
BUTTON 1
(HOLD FOR 2.5 SECONDS)
BUTTON 1
(HOLD FOR 2.5 SECONDS)
Honks horn, siren and park lights flash (if applicable) for
programmed alarm duration
Driver’s Priority Unlock
(if installed)
BUTTON 2
(2X WITHIN 3 SECONDS)
BUTTON 2
(2X WITHIN 3 SECONDS)
Driver’s door will unlock first then on second press all
doors unlock
Cold Start Selection (must be
enabled each time for use)
BUTTONS 1 & 3
(HOLD FOR 3 SECONDS)
BUTTONS 1 & 3
Toggles cold start mode on/off
Auxiliary 1
BUTTONS 1 & 4
BUTTON 1 & 4
Activates AUX 1
Auxiliary 2
BUTTONS 2 & 4
BUTTON 2 & 4
Activates AUX 2
Auxiliary 3
N/A
FUNCTION MENU
Activates AUX 3
Auxiliary 4
N/A
FUNCTION MENU
Activates AUX 4
Remote Sleep Mode
N/A
BUTTONS 1 & 2
Puts Remote to Sleep
No functions available while in Sleep Mode
STATUS REQUEST ON 2-WAY LCD
REMOTE
1.
2.
3.
4.
Pressing Button 4 once will tell you if your vehicle
is locked or unlocked.
Pressing Button 4 again within 4 seconds will
show your Remote Start Runtime remaining
Pressing Button 4 a third time within 4 seconds of
the last command will show your Interior Ambient
Temperature in the vehicle.
Pressing Button 4 a foruth time within 4 seconds of
the last command will show you the vehicle battery
voltage.
ENTERING FUNC TION MENU ON
2-WAY LC D REMOTE
1.
2.
3.
Push and Hold Button 4 and wait for FMENU to
appear on LCD screen
Use Button 1 to scroll through the Menu Options
To set desired option, scroll to option and press
Button 4.
MENU #
DESCRIPTION
1 - AUX 1
Activates AUX 1 output
2 - AUX 2
Activates AUX 2 output
3 - AUX 3
Activates AUX 3 output
4 - AUX 4
Activates AUX 4 output
5 - FIND
Honks Horn and Flashes Park Lights 5 times
6 - COLD
Turns Cold Start ON/OFF (Programmable through
Menu 2-08, 2-09, 2-10)
7 - VLET
Turns Service or Valet Mode ON/OFF
8 - ALRM
Turns Alarm Functions ON/OFF (Alarm Functions
must be turned ON in programming menu to work)
9 - SHCK
Disables Shock Sensor and AUX Shock Sensor
SE T TING CLOCK & PRECISE TIME
STAR T IN 2-WAY LCD REMOTE
1.
2.
3.
4.
To enter Programming Mode press and hold
Buttons 1 & 4 together for 3 seconds.
Using Button 1 to scroll through the Menu Options.
Button 2 will decrease and Button 3 will increase
minutes and hours in the selected menu.
The “Clock” icon will appear on the LCD screen
when you are setting the Precise Time Start. If it
is not displayed, you are setting the 2-Way LCD
Remote Clock.
Press Button 4 to Exit the Setting Menu.
11
SE T TING REMOTE FEATURES ON
2-WAY LC D REMOTE
1.
2.
3.
4.
Push and Hold Button 4 and wait for FMENU to
appear on LCD screen.
Press Button 2 to enter the menu and use Button
1 to scrol lthrought the Sub Menus.
Use Button 2 to set the option and advance you to
the next step.
Press Button 4 to exit the FMENU.
MENU #
DESCRIPTION
1 - CLK
Turns Precise Time Start On/Off
2 - CAR 1
Switches between Car 1 & Car 2 (operates
different car with same remote*)
3 - VIB
Turns Vibrate feature on remote On/Off
4-F
Cycles between Celsius and Farenheit for
interior ambient temperature display
5 - BLUE/
WHITE
Changes LCD screen colour from Blue or White
* req u ire s in s t al l ati o n o f S o l a ce R emote St ar ter M od ule in
se co n d c ar.
SE T TING EX TR A FEATURES ON
2-WAY LC D REMOTE
1.
2.
12
Push and Hold Button 4 and wait for FMENU to
appear on LCD screen.
Press Button 3 to enter the menu and use Button
3.
4.
1 to scrol lthrought the Sub Menus.
Use Button 1 to set the option and advance you to
the next step.
Press Button 4 to exit the FMENU.
MENU #
DESCRIPTION
1 - TEMP
Sets temperature for cold start
2 - RUN
Sets Remote Start Runtime
LOW BAT TERY WARNING
On 2-way LCD remotes there is a low battery warning
that will sound three long chirps after any command sent
and display “low bat”. This is an indicator to charge your
battery when possible.
BASIC VEHICLE COMMANDS
(1-WAY AND 2-WAY )
LOCK - Pressing Button 1 for less than 2 seconds will
lock the vehicle’s doors (if power locks connected).
The park lights will flash once and the siren/horn
will honk/chirp once. The LED’s on the antenna
will begin to flash. If a security system is installed
the system will be armed, along with starter disable
activated (extra parts and/or install required).
UNLOCK - Pressing Button 2 for less than 2
seconds will unlock the vehicle’s doors (if power
locks connected). The park lights will flash twice and
the siren/horn will honk/chirp twice. The LED’s on
the antenna will stop flashing. If a security system is
installed the system will be disarmed, along with starter
disable deactivated.
DRIVER’S PRIORITY UNLOCK - When programmed you can
set up your vehicle up to perform driver’s priority unlock.
Only the driver’s door will unlock when pressing button 2
for less than 2 seconds. Pressing button 2 a second time
for less than 2 seconds will unlock the rest of the vehicle’s
doors.(Extra Installation may be required)
the runtime remaining.
If you would like to extend the remote start runtime you
can do so by pressing button 3 for less than 2 seconds,
this will add 10 minutes to the remaining runtime.
With the vehicle running under remote start, pressing
and holding button 3 for more than 2 seconds will shut
off the remote start.
TRUNK RELEASE - Pressing Button 2 (4 on 1WAM)
for more than 2 seconds will activate the trunk release.
When activated this function will first unlock the doors,
disarm any security system and then open the trunk.
The park lights will flash three times and the siren/horn
will honk/chirp three times.
IDLE MODE - With the vehicle running by key, pressing
button 3 for less than 2 seconds will activate idle mode
(stop and go). With the vehicle running and key in the
ignition, be sure foot brake is not on and the vehicle
is in PARK or NEUTRAL and E-BRAKE on (manual
transmission). Press button 3 for less than 2 seconds;
the park lights will turn on and the siren/horn will honk/
chirp once. You can now remove the key from the
ignition and the vehicle will remain running. The vehicle
will run for the set runtime and shut off if left that long.
START - Pressing Button 3 for less than 2 seconds will
activate the remote start sequence. The park lights will
flash once and the siren/horn will honk/chirp once, then
the vehicle will start. Once the vehicle is started the
park lights will stay on solid and the vehicle will run for
the set runtime and shut down and flash the park lights
twice and siren/horn will honk/chirp twice. The 2-way
LCD remote will receive a command back and display
TURBO TIMER MODE - In the case your vehicle
is equipped with a turbocharged engine, it is
recommended to cool down the turbocharger. With
the vehicle running and key in the ignition, be sure foot
brake is not on and the vehicle is in PARK or NEUTRAL
and E-BRAKE on (manual transmission). Press button 4
for less than 2 seconds, the park lights will turn on and
the siren/horn will honk/chirp once. You can now
13
remove the key from the ignition and the vehicle will
remain running for the programmed turbo timer runtime
and then shut off. (This can also be programmed to
activate automatically every time you exit the vehicle.
Contact your dealer for more details)
SILENT LOCK/UNLOCK - If you wish to lock/arm
or unlock/disarm your vehicle silently you can do so
by pressing buttons 1 and 2 together for less than 2
seconds. This will toggle between lock and unlock.
This is only a temporary bypass of the audible lock/arm,
unlock/disarm and will return to normal by pressing lock
or unlock.
AUXILIARY 1 - Pressing buttons 1 and 4 together for
less than 2 seconds (on 1-way & 2-way LED remotes)
or enter FMENU on the 2-Way LCD remote, will
activate the AUX 1 which can be configured to open/
close sliding doors, trunk release, sunroofs, etc. (extra
parts and labor may be required). When activated this
function will first unlock the doors, disarm any security
system and then activate the auxiliary. The park lights
will flash three times and the siren/horn will honk/chirp
three times.
AUXILIARY 2 - Pressing buttons 2 and 4 together for
less than 2 seconds (on 1-way & 2-way LED remotes)
or enter FMENU on the 2-Way LCD remote, will
14
activate the AUX 2 which can be configured to open/
close sliding doors, trunk release, sunroofs, etc. (extra
parts and labor may be required). When activated this
function will first unlock the doors, disarm any security
system and then activate the auxiliary. The park lights
will flash three times and the siren/horn will honk/chirp
three times.
AUXILIARY 3 - Enter FMENU on the 2-Way LCD
remote will activate the AUX 3 which can be configured
to open/close sliding doors, trunk release, sunroofs, etc.
(extra parts and labor may be required). When activated
this function will first unlock the doors, disarm any
security system and then activate the auxiliary. The park
lights will flash three times and the siren/horn will honk/
chirp three times.
AUXILIARY 4 - Enter FMENU on the 2-Way LCD
remote will activate the AUX 4 which can be configured
to open/close sliding doors, trunk release, sunroofs, etc.
(extra parts and labor may be required). When activated
this function will first unlock the doors, disarm any
security system and then activate the auxiliary. The park
lights will flash three times and the siren/horn will honk/
chirp three times.
CAR FINDER - Pressing buttons 3 and 4 together
simultaneously will chirp the horn and siren for 3
seconds in order to find your car in a parking lot. The
park lights will also flash for this time.
PANIC MODE - If button 1 is pressed and held for
more than 2 seconds panic mode will be activated. This
will honk the horn, turn the siren on (if connected), and
flash the park lights for the programmed duration.
COLD START - To activate Cold Start, press Buttons 1 and
3 together (on AM remotes hold for 3 seconds). This
will then activate the programmed Cold Start and start
your car at the programmed temperature and time. To
deactivate Cold Start, press Buttons 1 and 3 together
(on AM remotes hold for 3 seconds) or cycle the ignition
ON-OFF. The park lights and horn will honk 1 time for
ON mode and 2 times for OFF mode. Cold start must be
enabled everytime after the vehicle has been driven.
READY MODE SEQUENCE
(MANUAL TR ANSMISION)
There are 3 different ways to activate “READY MODE”.
This is necessary to ensure that a manual transmission
vehicle is in neutral with the emergency brake on and
all doors are shut. To have a different “ready mode”
activation please ask your dealer to program the desired
method. If any door is opened or park brake disengaged
after “ready mode” has been initialized, the remote start
WILL NOT work and a “not in ready mode” diagnostic
will appear when attempting to remote start.
OPTION 1 (default) - Emergency brake activation
1. With vehicle running by key and the vehicle in
neutral, apply the emergency brake.
2. The park lights will turn on.
3. Remove the key from the ignition cylinder (the
vehicle will remain running).
4. Exit the vehicle; upon closing the last door Press
the Lock Button and the vehicle will shut off.
5. The vehicle is now in ready mode and the “Ready
Mode” icon will appear on the 2-way remote and
can now be started by remote.
OPTION 2 - Brake pedal activation.
1. With vehicle running by key and the vehicle in
neutral, apply the emergency brake and depress
the foot brake twice within 2 seconds.
2. The park lights will turn on.
3. Remove the key from the ignition cylinder (the
vehicle will remain running).
4. Exit the vehicle, upon closing the last door the
Press Lock and the vehicle will shut off.
5. The vehicle is now in ready mode and the “Ready
Mode” icon will appear on the 2-way remote and
can now be started by remote.
15
OPTION 3 - Remote activation
1. With vehicle running by key and the vehicle in
neutral, apply the emergency brake and press
button 4 on the remote.
2. The park lights will turn on.
3. Remove the key from the ignition cylinder (the
vehicle will remain running)
4. Exit the vehicle; upon closing the last door, Press
and hold the Start button and the vehicle will shut
off.
5. The vehicle is now in ready mode and the “Ready
Mode” icon will appear on the 2-way remote and
can now be started by remote.
OPTION 4 - Idle mode
1. With vehicle running by key and the vehicle in
neutral, apply the emergency brake and press
button 3 on the remote.
2. The park lights will turn on.
3. Remove the key from the ignition cylinder (the
vehicle will remain running)
4. Exit the vehicle; upon closing the last door the
vehicle will stay running until you press and hold
button 3 to shut down the vehicle.
5. The vehicle is now in ready mode and the “Ready
Mode” icon will appear on the 2-way remote and
can now be started by remote.
16
If you press button 3 on the remote with the emergency
brake engaged the remote starter will go into idle mode
and WILL NOT shut down after the last door is closed.
It will run for the set run time then shut off and remain in
“ready mode”. You can also shut the vehicle off after the
last door is closed by pushing and holding button 3 for
more than 2 seconds. This is convenient if you have to
get anything from other doors after closing the driver’s
door.
IMPORTANT - If any door is opened while the vehicle
is not running and in “ready mode” the system will
automatically exit “ready mode” and remote start feature
will be deactivated. You will need to re-initialize the
“ready mode” sequence again. If you need to access
the vehicle while it is in “ready mode” you can remote
start the vehicle, open the door as you wish, then shut
down the vehicle by remote and the remote starter will
remain in “ready mode”.
VALE T/SER VICE MODE
This will disable all remote start and security features
of the system. When in valet mode the lock, unlock,
and trunk features will still work. The system MUST be
put into service/valet mode whenever any work is to be
done on the vehicle, or parked in any enclosed/partially
enclosed area
ENTERING SERVICE MODE
1. Turn the key to the “Ignition On” or “RUN” position.
2. Press and hold the programming button located
on the remote starter antenna (located on
windshield) for 8 seconds or until the horn/siren
pulses 5 times. If programmed for Secure Valet
hold program button for 30 seconds instead of 8
seconds.
2.
Press and hold the programming button on the
remote starter antenna (located on windshield) for
8 seconds or until the horn/siren pulses 2 times. If
programmed for Secure Valet hold program button
for 30 seconds instead of 8 seconds.
The system is now out of Valet/Service mode. To confirm
this, the LED on the antenna will be off or flashing and if
a start is attempted the vehicle will start successfully.
The system is now in Valet/Service mode. To confirm
this, the LED on the antenna will be solid and if a start
is attempted you will get a VALET diagnostic code from
the park lights.
EXITING SERVICE MODE
1. Turn the key to the “Ignition On” or “RUN” position.
17
ALARM FEATURES
You MUST turn on alarm features in order for this unit to operate as a
starter/alarm combo. It is Menu 3-03 - Option 2.
You can set up this unit to monitor door pins, ignition,
hood, and trunk like a factory style content alarm system,
or you can add the “Alarm Kit” which includes a Dual
Stage Shock Sensor and a Siren. With this kit installed
you will have complete protection from any impact to
your vehicle.
The Shock sensor has 2 triggers. Warn away lets the user
know that there was a light impact alarm trigger. If the
car receives a light impact the siren will chirp 3 times
and the park lights will flash to warn away any possible
intruders. If the car receives a hard impact, the siren and/
or horn will sound and the park lights will flash for the
programmed alarm time. (Default is 60 seconds)
This unit is also capable of installing extra sensors such
as tilt/motion sensors, audio sensors, and microwave
sensors etc. This is a separate sensor port and will not
affect the sensitivity of the D/A shock sensor.
Shock sensor bypass - To temporarily bypass any
alarm sensors plugged in simply press button 1 then
button 2 within 1 second. This will ignore any triggers
from any sensors plugged into the remote starter/alarm.
18
The sensors will be reactivated the next time the system
is armed by remote.
A LA R M FA I LU R E D I AG N O S T I C S
If you arm the system and there is an open zone, the
alarm system will honk/siren 3 times notifying you of the
open zone. If equipped with a 2-way LCD remote, the
open zone will be displayed on the screen.
ALARM
TRIGGER
PARK LIGHT
FLASHES
2-WAY LCD
TEXT
Shock Sensor
3
Shock Alarm
Foot Brake
4
Brake Alarm
Door
5
Door Alarm
Hood
6
Hood Alarm
Aux
7
Aux Alarm
Ignition
8
Ign Alarm
The LCD back light will alternate between white and red
and follow up with an audible warning when an alarm
trigger has been detected.
TRANSMITTER LEARNING
Important! The remote starter will hold 3 transmitter
codes. It is recommended that when programming in
transmitters, you fill up all four transmitter codes, even
if only using one or two transmitters. This will clear
all other transmitter coding from the unit and prevent
stray coding or possible interference from other remote
transmitters.
1. Turn ignition ON-OFF-ON.
2. Press the valet switch TWICE (button) in the
antenna, siren/horn (optional) will chirp once each
time button is pressed.
3. Press and hold the valet switch, siren/horn will
chirp 3 times & parking lights will turn on to
indicate you have entered Transmitter Learning
Mode.
4. Press button 1 (Lock) of every transmitter to
be coded. The siren/horn will chirp once and
the parking lights will flash once to indicate
successfully learning. System will exit Learn
Mode and lights will turn off after 15 seconds of
no activity.
5. Turn ignition OFF and the unit will exit codelearning mode.
BATTERY REPLACEMENT
If you notice decreased range in your remote transmitter,
it is possible that your transmitter battery needs to be
replaced. To replace your battery:
ON 1-WAY REMOTE TRANSMITTER:
1. Remove the small Phillips screw on the back side
of the remote.
2. Once removed gently pull the remote transmitter
apart, taking care not to damage the circuit board.
3. Remove the battery and replace with a new
battery. If you having trouble finding the proper
size of the battery, the model number is printed on
the battery casing.
4. Replace back cover of remote transmitter and
replace Phillips screw.
ON 2-WAY LED & 2-WAY LCD REMOTES:
1. The batteries in these remotes are rechargeable.
To recharge the battery, locate the rechargeable
cable input on the side of the remote.
2. Plug in the supplied recharge cable that came
with your remote starter and let the remote
transmitter charge till LED Charged Status
illuminates. (if your charger/cable is not equipped
with an LED charge time is approx 2 hours).
19
REMOTE SLEEP MODE
Available on the 2-Way LED and 2-Way LCD remote
transmitters, this function allows you to put your remote
into Sleep Mode so that you do not have unneccessary
battery life drain when away from your vehicle for
extended period of time.
Press and Hold Buttons 1 and 2 togerther for
approximately 8 seconds to put your remote into Sleep
Mode or to take it out of Sleep Mode. The remote will
beep a few times indicating OFF/ON.
eco-run
This Solace Remote Starter is equipped with eco-run
technology. This technology has been designed to not
only save money on fuel, but also save emissions going
into the environment. Eco-run can be used to follow
anti-idling laws, and/or automatically shut your vehicle off
once at the desired interior ambient cabin temperature,
saving fuel and wear and tear on your vehciles motor.
There are three different programmable options to
achieve your level of savings.
eco-run START TEMPERATURE
This setting allows you to adjust the temperature as
20
to which your vehicle will start. When below this set
temperature the vehicle will run for the set run time, if
above the set temperature your vehicle will run for 1
minute. This option can be used for anti-idling laws and/
or reduced run time when the temperature is warmer.
eco-run RUN TIME
This setting allows you to adjust how long the vehicle
will run when remote started in eco-run mode,
conforming to anti-idling laws in all areas. This setting
will work in conjunction with the start temperature and
the run temperature.
eco-run RUN TEMPERATURE
This setting monitors the interior cabin temperature of
the vehicle and shuts down the remote starter once the
preset (or desired) temperature has been reached.
Any of the features for eco-run MUST be initialized at
the time of install. Please ask your Solace dealer for
more details.
RE M OTE STA R T FAILURE DIAGNO S T IC S
PARK LIGHT
FLASHES
2-WAY LCD TEXT
Not In Ready Mode
3
Reserve Fault
Foot Brake On
4
Brake Fault
Valet Mode
5
Stop
Hood
6
Hood Fault
Failed Start/No
Tach Programmed
7
Tach Fault
Ignition On
8
Ign Fault
FAULT
Please see Solace Dealer for repair.s
RESET 7 FLASH PARK LIGHT DIAGNOSTIC on
REMOTE START
If at any time your vehicle fails to start for any reason the
Solace remote starter may go into protedtion mode. To
re-learn peform the following steps:
1. Start vehicle by key/push button.
2. Press and hold the foot brake.
3. Press and release the programming button 1 time (+
button on receiver by rear view mirror)
4. Release the foot brake.
5. Wait 15 Seconds.
6. Turn vehicle off.
7. Remote Start
If your vehicle still does not remote start please contact
your nearest Solace dealer.
21
For more information please visit our website:
www.SolaceRemoteStarters.com
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising