Solis 50 Operator's Manual
Add to my manuals
100 Pages
Solis 50 is a robust and versatile tractor designed to meet the demands of modern agriculture. With its powerful engine, advanced hydraulics, and user-friendly controls, Solis 50 empowers you to handle a wide range of farming tasks with ease. Whether you're cultivating fields, transporting heavy loads, or operating implements, Solis 50 delivers the performance and reliability you need to get the job done efficiently.
advertisement
OPERATOR MANUAL
SOLIS - 50
INTERNATIONAL TRACTORS LIMITED
HOSHIARPUR
INDIA
PART NO :— 10071297AA
2
OWNERSHIP AND TRACTOR DETAILS
OWNER’S NAME
& ADDRESS
-------------------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------- TEL No. -------------------------------------
Model :
Chassis No.
Engine No.
Battery Make / Sr. No.
FIP Sr. No. :
Tire
Front
Front
Rear
Rear
(Left)
(Right)
(Left)
(Right)
Make
Delivery Date :
Bill No. / Date :
Alternator Make / Sr. No.
Starter Motor Make / Sr. No.
Hydraulic Pump Make / Sr. No. :
Size Sr. No.
I have under stood all the terms & conditions of the maintenance of the tractor, terms of warranty, systems,
Scheduled services & understood operation of tractor in the field and other operations
Received a new defect free tractor Chassis No. .. ...................................................................... Engine No.
.....................................................
& fully satisfied with the transaction.
OWNER SIGNATURE DEALER STAMP & SIGNATURE
PH. No. ........................................ DATE : .........................
* IMPORTANT INFORMATION TO CUSTOMER:
For any assistance with regard to our product, please contact our authorized dealer or authorized service center.
OWNERSHIP AND TRACTOR DETAILS
OWNER’S NAME
& ADDRESS
-------------------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------- TEL No. -------------------------------------
Model :
Chassis No.
Engine No.
Battery Make / Sr. No.
FIP Sr. No. :
Tire
Front
Front
Rear
Rear
(Left)
(Right)
(Left)
(Right)
Make
Delivery Date :
Bill No. / Date :
Alternator Make / Sr. No.
Starter Motor Make / Sr. No.
Hydraulic Pump Make / Sr. No. :
Size Sr. No.
I have under stood all the terms & conditions of the maintenance of the tractor, terms of warranty, systems,
Scheduled services & understood operation of tractor in the field and other operations
Received a new defect free tractor Chassis No. .. ...................................................................... Engine No.
.....................................................
& fully satisfied with the transaction.
OWNER SIGNATURE DEALER STAMP & SIGNATURE
PH. No. ........................................ DATE : .........................
* IMPORTANT INFORMATION TO CUSTOMER:
For any assistance with regard to our product, please contact our authorized dealer or authorized service center.
PREFACE
Dear Customer, we welcome you with great pleasure in your joining the
ITL
family and thank you for the faith and trust you have placed in the careful selection of your tractor.
Before using this tractor it is highly recommended to read this manual thoroughly. Any person who regularly or occasionally uses your tractor should be encouraged to read these instructions.
Daily and routine maintenance operations can be easily performed with the use of this manual. Our dealers would be pleased to assist you in the maintenance of your tractor and help economical operation.
Use only genuine ITL spare parts from dealers/stockist. It would fetch you a reliable and durable performance.
Information provided in this operator manual is accurate at the time of printing. Improvement and modifications is a continuous process at
International Tractor Limited (ITL),
be reserve the right to modify at any time without prior notice.
You are the proud owner of the best product for your prosperity. In case of any help/support required please feel free to call our dealership with the tractor details like Engine number and
Chassis number. We wish your prosperity and our growth.
Export Department
INTERNATIONAL TRACTORS LIMITED
Vill.-Chak Gujran, P.O. Piplanwala 146022
Jalandhar Road, Hoshiarpur, Punjab, India.
Phone: +91-1882-302-525/526
E-mail: [email protected]
7
8
YOUR RIGHTS
While taking delivery of new
"ITL" Tractor,
kindly ask the dealer to give following items free of cost:
1.
Tool kit which includes
l l l l
Grease gun (4 Cylinder)
Cutter plier 8”
Screw driver 5”
D-spanner 10 X 11
1pc
1pc
1pc
1pc l l l l
D-spanner 12 X 13
D-spanner 14 X 17
D-spanner 18 X 19
D-spanner 20 X 22
1pc
1pc
1pc
1pc l l l l l l
D-spanner 30 X 32
Ring spanner 16 X 17
Ring spanner 24 X 27
Battery Guarantee card
Hydraulic Jack (Optional)
Rear Wheel Spanner Kit (Optional)
1pc
1pc
1pc
1pc
1pc
1pc
2.
Farmer Kit
l
Diesel Filter( Primary) l l
Diesel Filter( Secondary)
Lub. Oil Filter l l l l l l
Fan Belt
Cap Radiator
Cap Fuel Tank
Linch Pin
Fuse Box
Tyre pressure gauge
3pc
3pc
2pc
1pc
1pc
1pc
3pc
1pc
1pc
3.
To avail the services.
4.
To call dealers any time for any breakdown.
Operator Manual
Operator Manual
CONTENTS
Sr. No. DESCRIPTION
IDENTIFICATION OF TRACTORS
1
SAFETY NOTES
INSTRUMENT PANEL AND ELECTRICAL CONTROLS AND TOOP HOOD
1.1. INSTRUMENT PANEL
2
1.2 ELECTRICAL CONTROLS
1.3 PROCEDURE TO OPEN THE TOP HOOD
1.4
REAR VIEW MIRROR
1.5
COLD START UNIT
ELECTRICAL EQUIPMENTS
2.1 BATTERY
3
4
5
2.2 ALTERNATOR
2.3 STARTER MOTOR
2.4 GENERAL MAINTENANCE OF ELECTRICAL SYSTEM
ENGINE
3.1 STARTING THE ENGINE
3.2 STOPPING THE ENGINE
3.3 RUNNING IN ENGINE
3.4 FUEL SYSTEM
3.5 ENGINE LUBRICATION SYSTEM
3.6 GENERAL MAINTENANCE
3.7 AIR CLEANER
3.8 RADIATOR
CONTROLS
4.1 HAND CONTROLS
4.2 FOOT CONTROLS
4.3 SEVEN PIN SOCKET
HYDRAULIC
6
7
5.1 HYDRAULIC SYSTEM
5.2 HYDRAULIC CONTROL OPERATIONS
5.3 THREE POINT LINKAGE
5.4 GENERAL MAINTENANCE
WHEELS AND TYRES
6.1 IN FIELD OPERATIONS
6.2 ON ROAD OPERATIONS
6.3 BALLASTING OF TRACTOR
6.4
RECOMMENDED LOAD CARRYING CAPACITY PER TYRE W.R.T. ITS SIZE
6.5 TRACK WIDTH ADJUSTMENT
6.6 TIPS FOR PROPER HANDLING AND DURABILITY OF TYRES
6.7 GENERAL SUGGESTIONS
6.8 CHECK WHEEL NUT BOLT
FRONT AXLE 4WD (OPTIONAL)
7.1 FRONT AXLE 4WD
45
46
46
46
48
50
52
52
54
56
57
44
44
44
45
45
45
PAGE NO.
11
13
36
36
40
41
41
41
42
42
67
68
68
62
62
64
64
66
67
57
57
58
59
61
61
9
10
8
9
10
11
12
13
14
15
CONTENTS
7.2
SWINGING DRAW BAR
7.3 ROLL OVER PROTECTION
7.4
PNEUMATIC TRAILER BRAKES (OPTIONAL)
7.5
PNEUMATIC TRAILER BRAKE COMPONENTS
7.6
HYDRAULIC TRAILER BRAKE
7.7
HYDRAULIC TRAILER BRAKE FREE PLAY ADJUSTMENT
7.8
HYDRAULIC TRAILER BRAKE COUPLER
OTHERS
8.1 REGISTRATION PLATE
8.2 LIGHTS
8.3 REFLECTOR
8.4 EXHAUST MUFFLER
8.5 HEAT INSULATION SHEET
8.6 PTO GUARD
8.7
DRIVER SHEET (E-MARKED)
8.8
RECOMMENDED SCHEDULE FOR MAINTENANCE SERVICE
8.9
ELECTRICAL WIRING CIRCUIT DIAGRAM
8.10 RECOMMENDED GRADE OF LUBRICANTS & GREASES
8.11 GREASING POINT ON TRACTORS
WARRANTY POLICY
TROUBLE SHOOTING
SPECIFICATION
FREE SERVICE COUPON
SERVICE RECORDS
NOTES
FEEDBACK CARD
Operator Manual
84
87
95
77
77
79
81
72
72
73
73
74
76
96
97
70
70
72
72
72
72
68
68
69
69
70
Operator Manual
IDENTIFICATION OF TRACTOR
1.
In this manual it is written many times
front portion, rear portion, left side, right side,
understand these terms as per reference Fig.
2.
While ordering spare parts always mention the chassis number of the tractor and engine. These numbers are punched on the data plate which is riveted on left hand fender. By giving these numbers correctly you will get delivery of the right parts at right time. Refer Fig.
Fordata plate.
3.
The serial No for E Marked ROPS is also riveted on the left side of the ROPS refer Fig.
Left Side
INTERNATIONAL TRACTORS LTD.
Type: ...............................................................................
ECE number ...................................................................
Identification number: ...............................................................................
Total permissible mass (*) :
.............................to ........................kg
Permissible front axle load (*):
.............................to ........................kg
Permissible rear axle load (*):
.............................to ........................kg
(*) depending on the tyres.
Permissible towable mass:
Unbraked towable mass:
Independently-braked towable mass:
Inertia-braked towable mass:
........................kg
........................kg
........................kg
Towable mass fitted with an assisted braking system :
(hydraulic or pneumatic)
........................kg
INTERNATIONAL TRACTORS LIMITED
HOSHIARPUR, PUNJAB (INDIA)
Rear Portion
S e
4
0080
Tractor Model
INTERNATIONAL
TRACTOR LIMITED
TRACTOR TYPE T 1
Serial No.
11
12
Operator Manual
WHOLE VEHICLE TYPE APPROVALS FOR TRACTOR
TRACTOR EC TYPE APPROVAL NO
e4*2003/37*0057*01 e4*2003/37*0051*03
TRACTOR MODEL
SOLIS 50 4WD Including all variants with up Draft/ Down Draft, Power Steering/
Mechanical Steering, Radial Tyres, Air Trailer Brake/Hydraulic Trailer Brake
SOLIS 50 2WD Including all variants with up Draft/ Down Draft, Power Steering/
Mechanical Steering, Radial Tyres, Air Trailer Brake/Hydraulic Trailer Brake
Sr. No.
Name of Device
3
4
1
2
Main Beam Head Lamp
Dim Beam Head Lamp
Front Direction Indicator
Front Position Lamp
9
10
11
7
8
5
6
12
13
14
Rear Direction Indicator
Stop Lamp
Rear Position Lamp
Registration Plate Lamp
Reflector
Driver Seat
Audible Warning Device
Rear View Mirror
ROPS
Swinging Drawbar
E-marked Components
Component Type approval No.
E4-112R-000223
E4-112R-000223
E4-6R-0111359
E4-7R-0211359
E4-6R-0111358
E4-7R-0211358
E4-7R-0211358
E4-4R-004125
E4-3R-023232 e4*78/764*1999*/57*0009*00
E4-28R-000153
E4-46R-022764 e4*2009/75*2009/75*0080*00 e4*2009/144*2010/62*0049*00
Operator Manual
SAFETY NOTES
A. SAFETY ALERT SYMBOLS AND TERMS
This safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
The safety alert symbol identifies important safety messages on machines, safety signs, in manuals or elsewhere. When you see this symbol, be alert to the possibility of personal injury or death.
Why is SAFETY important to you? *ACCIDENT DISABLE and KILL*
* ACCIDENTS are COSTLY * * ACCIDENTS can be AVOIDED*
SAFETY: TRACTOR and IMPLEMENT
other attachment does it become a working unit.
base tractor operation.
F
that may be fitted at the time of tractor delivery or at some future date.
attachments.
B. SAFETY: INTRODUCTION
This safety section of your Operator Instruction book is intended to point out some of the basic safety situations which may be encountered during the normal operation and maintenance of your
PLATFORM, and to suggest possible ways of dealing with these situations. This section is NOT a replacement for other safety practices featured in other sections of this book.
Additional precautions may be necessary depending on attachments used and conditions at the work site or in the service area. The tractor manufacturer has no direct control over tractor application, operation, inspection, lubrication or maintenance. Therefore it is
YOUR responsibility to use good safety practices in these areas.
C. SAFETY: A WORD TO THE
OPERATOR
It is YOUR responsibility to read and understand the safety section in this manual before operating your tractor. You must follow these safety instructions that
In reading this section, you will note that illustrations have been used to highlight certain situations. Each illustration is numbered and the same number appears in the text in parenthesis. This number is placed at the end of the written text that refers to the illustration and is made up of two digits, separated by a hyphen: the first digit designates the chapter, the second one of the figure number in that chapter,
Remember that YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Study the features in this manual and make them a working part of your safety program.
Keep in mind that this safety section is written only for this type of machine. Practice all other usual and customary safe working precautions, and above all REMEMBER: SAFETY
IS YOUR RESPONSIBILITY. YOU CAN PREVENT
13
14
Operator Manual
D. SAFETY: DANGER, WARNING and CAUTION
Whenever you see the words and symbols shown below, used in this book and on decals, you MUST take note of their instructions as they relate to personal safety.
DANGER: The symbol and the word DANGER indicates an imminently hazardous situation, which, if not avoided, will result in DEATH OR
VERY SERIOUS INJURY.
WARNING: The symbol and the word
WARNING indicate a potentially hazardous situation. if the instructions or "procedures are not correctly followed it could result in DEATH
OR SERIOUS INJURY.
CAUTION: The symbol and the word
CAUTION indicate a "potentially hazardous situation, which, if not avoided, may result in
MINOR INJURY.
IMPORTANT: The word IMPORTANT is used to identify special instructions or procedures which, if not strictly observed, could result in damage to, or destruction of the machine, process or its surroundings.
NOTE: The word NOTE is used to indicate point of particular interest for more efficient and convenient repair or operation.
SAFETY: DECALS
WARNING: DO NOT remove or obscure
Danger, Warning, Caution or Instruction decals.
E. SAFETY: FOLLOW A SAFETY
PROGRAM
For safe operation:
For safe operation of an agricultural tractor, you must be a qualified and authorized operator. To be qualified you must understand the written instructions supplied in this Operator Instruction Book, have training, and know the safety rules and regulations for the job.
Some regulations specify, for example, that no one under the age of 18 years (according to European
Rules) may operate power machinery. This includes tractor, it is your responsibility to know what these regulations are, and obey them, in the operating area of situation.
These will include, but are not limited to, the following instructions for safe tractor operations:
WARNING : An operator should not use alcohol or drugs which can change his/her alertness or co-ordination. An operator on prescription or 'over the counter' drugs needs medical advice on whether or not he or she can properly operate machines.
Observe the following precautions:
operate your tractor. Keep others away from your area of work.
a safety frame in the upright position.
ditches, embankments and holes. Reduce speed when turning, crossing slopes, and on rough, slippery, or muddy surfaces.
Replace any Danger, Warning, Caution or Instruction
Decals that are not readable or are missing.
Replacement decals are available from your Dealer in the event of loss or damage. The actual location of these safety Decals is illustration at the end of this section.
If a used tractor has been purchased, refer to the illustration at the end of this section to ensure that all the safety warning decals are in the correct position and are readable.
on roads, and around trees.
implement unless an approved passenger seat is fitted.
points, and never above the center line of the rear axle.
or stops, when the tractor is stopped, apply the parking brakes securely.
Operator Manual
F. SAFETY FRAME
A Safety Structure and seat belt is fitted as standard equipment to the platform tractor at the time of factory assembly. If the safety frame was deleted by the original purchaser or has been removed, it is recommended that you equip your tractor with a
Safety Structure and a seat belt. Safety frames are effective in reducing injuries during overturn accidents. A tractor overturning without safety frame can result in serious injury or death
Depending on laws in force in the various markets, a seat may be installed. Always raise the safety frame before may be installed. Always raise the safety frame before fastening the seat belt.
If a fold-down safety frame is installed. DO NOT wear a seat belt when the safety frame is in folded down position. NEVER keep the safety frame in the folded down position when working with the tractor.
Operation:
frame is not damaged, that it is securely fastened to the tractor, and, if a hinged section is fitted, that it is in the raised position and secured.
tractor, or folded down for a specific operation, it must be refitted or erected immediately using the proper hardware and applying the recommended torque value.
safety frame for pulling purposes; this will cause the tractor to tip backwards. Always pull from the tractor drawbar.
belt-adjusted snugly except when operating with a folded down safety frame or if the safety frame has been removed belt must be replaced
Damage to the safety frame
If the tractor has rolled over or the safety frame has been damaged (such as striking an overhead object during transport), the safety frame must be replaced to provide the original degree of protection.
After an accident, check for damage to the safety frame operator's seat, seat belt and seat mountings.
Before you operate the tractor, replace all damaged parts.
DO NOT WELD, DRILL, BEND OR STRAIGHTEN
THE SAFETY FRAME. IF DONE, reduce the protection it offers.
15
Operator Manual
16
G. SAFETY: PREPARE FOR SAFE
OPERATION
Protect yourself:
Wear all the protective clothing and personal safety devices issued to you or called for by job conditions. Don't take risk hence you may carry/wear the following
(a) A hard hat.
(b) Safety glasses, goggles or face shield.
(c) Hearing protection.
(d) Respirator or filter mask.
(e) Inclement weather clothing.
(f) Reflective clothing.
(g) Heavy gloves (neoprene for chemical, leather for rough work).
(h) Safety shoes.
DO NOT wear loose clothing, jewellery or other items and tie up long hair which could catch on controls or other parts of the tractor.
Learn where fire extinguishers and first aid or emergency equipment is kept and where to get help in a hurry. Make sure you know how to use this equipment.
(a)
(c)
(e)
(g)
(b)
(d)
(f)
(h)
Operator Manual
H. Know your equipment:
Know your tractor. Know how to operate all equipment on your machine and the implements and attachments used with it.
Know the purpose of all the controls, gauges and dials. Know the rated load capacity, speed range, braking and steering characteristics turning radius and operating clearances.
Keep in mind that rain, snow, ie, loose gravel, soft ground, etc. can change the way your tractor operates.
Under poor conditions, slow down and be extra careful, engage
four wheel drive, if fitted.
Study the DANGER, WARNING or
CAUTION safety signs on your tractor and the information signs also.read this operator instruction book before starting the engine.
study it before you start the work.
if there is something in the manual you don't understand, ask someone (such as your equipment dealer) to explain it to you.
IMPORTANT: This manual covers general safe practices for agricultural tractor it must always be kept with the tractor. For further copies contact your Dealer.
17
18
I. Use all available protective devices
Keep all protective devices in place and securely fastened. Make certain all guards, shields safety signs are properly installed, as specified, and are in good condition.
IMPORTANT: To help keep you and others around you safe, your tractor should be equipped with:
Safety belt. It must always be mounted in protection position . A seat belt is recommended according to law requirements on the respective market when ROPS is erected.
Tractors PTO shield.
Your tractor may also need:
Rear view mirrors.
Fire extinguisher.
SMV (Slow Moving Vehicle) emblem, Additional guards, lights or decals and additional alarm.
Know which devices are required for safe operation of your tractor. Use them. Make sure they are in place and in good condition. NEVER remove or disconnect any safety device.
Check the equipment:
Before you begin your working day, take time to check your tractor and ensure that all systems are in good operational condition.
DO NOT smoke while refueling the tractor. Keep any type of open flame away
Check for loose, broken, missing, or damaged parts.
Have everything put into good repair. Make certain all safety devices are in place.
Check safety frame and seat belt for damage. A damage safety frame or seat belt MUST be replaced.
Ensure that implements and attachments are properly installed and that the tractor and implement PTO RPM ratings match.
Check the tires for cuts, bulges and correct pressure.
Replace worn or damaged tires. Check foot and parking brakes for proper operation. Adjust if necessary.
AREA FOR REFILLING FUEL
Operator Manual
Operator Manual
refueling. Check the engine oil level and add oil if required.
the maintenance and adjustment section of this manual.
latched.
guards are in place and operating properly.
system. Have any leaks or damaged parts repaired or renewed.
WARNING: Diesel fuel or hydraulic fluid under pressure can penetrate the skin or eyes and cause serious personal injury, blindness or death. Fluid leaks, under pressure, may not be visible. Use a piece of cardboard or wood to find leaks. Never use your bare hand. Wear safety goggles for eye protection. If any fluid is injected into the skin, it MUST be surgically removed within a few hours by a doctor familiar with this type of injury
Before applying pressure to the fuel or hydraulic system, be sure all connections are tight and that lines, pipes, and hoses are not damaged. Before disconnecting fuel or hydraulic lines, be sure to relieve all pressure.
Make sure that all hydraulic lines are correctly installed and not tangled.
WARNING : Liquid cooling systems build up pressure as the engine gets hot. Before removing the radiator cap, stop the engine and let the system cool.
Check the engine cooling system and add coolant as required.
J. Clean the tractor:
clean.
implements to the ground, place transmission in neutral, engage the parking brake, shut off the engine and remove the key.
oil, Brush away dust or mud. In winter, scrape away snow and ice. Remember-slippery surfaces are dangerous.
console, instrument panel, monitors, indicators etc.), do not use petrol, paraffin, diluents etc.
warping of the cleaned parts.
neutral soap and a soft cloth..
in their proper places.
19
20
K. Protect the environment:
It is illegal to pollute drains, water courses or soil. Use authorized waste disposal facilities, including civic amenity sites and garages providing facilities for disposal of used oil. If in doubt, contact your local authority for advice.
To get to know the correct methods to dispose of oils, filters, tyres etc. contact your Dealer or the local agency for waste recycling.
L. Only for North America:
The safety sheets of each material give information on chemicals contained in a product, procedures to use it safely, first-aid and procedure to be followed in case of leakage or spills. In all North America such safety sheets are available at the Dealer's.
Before any maintenance on the machine refer to the above mentioned safety sheets for fluids, oils etc. used in this machine. The sheets inform about risks and safe maintenance procedures. We strongly recommended following these indications during any maintenance operations.
Disposal of the tractor: The tractor is made up of parts subjected to rules and laws for their disposal.
When the tractor is not used any more, it must be disposed of through proper agencies according to such rules. Do not pollute the environment with the tractor or its parts.
Operator Manual
M. SAFETY: SERVICING THE TRACTOR
DO NOT service the tractor while the engine is running or hot, or if the tractor is in motion
Before making adjustments to, or servicing the electrical system, disconnect the battery cables, negative (-) cable first.
To prevent fires or explosions keep open flames away from the battery to cold weather starting aids. To prevent sparks which could cause explosion use jumper cables according to instructions.
When making repairs or adjustments it is recommended that you consult your Dealer, and have the work carried out by trained personnel.
The implement and/or tractor must be supported on suitable wooden blocks or stands, NOT a hydraulic jack.
Check all nuts and bolts periodically for tightness especially wheel hub and rim nuts. Tighten to the prescribed torque values.
Check the power steering reservoir regularly and top up as necessary with approved oil.
Check the brakes regularly, top up the reservoir and/or adjust where necessary. Make sure that the brakes are evenly adjusted.
Operator Manual
N. SAFETY: STARTING
Warn bystanders before starting:
Before starting, Walk all around the tractor and any attached equipment. Make sure that no one is under it, on it, or close to it. Let other workers and bystanders know you are starting up and don't start until everyone is clear of the tractor, implements and towed equipment.
Ensure that all bystanders, particularly children are in a safe position before starting the engine.
Mount and dismount properly:
Always use 'three point contact' with the machine, and face the machine when you mount it. Three point contact means both hands and one foot or one hand and both feet are in contact with the machine at all times during mounting and dismounting.
Clean the soles of your shoes and wipe your hands before climbing on. Use handrails, grip handrails, ladders or steps (as provided) when mounting or dismounting.
NEVER use control levers as a hand hold and
NEVER step on foot controls when mounting or dismounting.
NEVER attempt to mount or dismount from a moving tractor. NEVER jump off a tractor in any circumstances.
Start safely.
WARNING : Before starting the engine, make sure there is plenty of ventilation. Never operate the engine in a closed building. The exhaust fumes may cause asphyxiation.
Always start the engine from the operator's seat with all the transmission levers and PTO lever in neutral.
Make sure that the tractor dual brake pedals are locked together at all times unless you are making turns in the field which require independent use of the brakes. Make sure the brakes are properly adjusted so that both brakes engage at the same time.
Adjust the seat, fasten the seat belt (where applicable as outlined in this manual), apply the parking brake and put all controls in neutral before starting up.
DANGER : Start the engine, with the starter key, from the operator's seat only. Never attempt to start the engine by shorting across the starter terminals. The machine will start in gear if the neutral start circuit bypassed. This could cause serious injury or death to anyone near the tractor.
21
22
Operator Manual
O. Follow recommended starting procedures
Follow the starting procedures recommended in the operation section of this Operator instruction Book. This includes normal starting, cold starting and use of starting fluids.
Test the controls
After starting, recheck all gauges and lights. Make sure everything is functioning correctly. If the tractor does not respond correctly which each control is operated, DO
NOT use the machine until the fault is rectified
Ensure that the starter solenoid cover is always in position.
Starting fluid
WARNING : It is very important that you read the label on the can before using starting fluid. DO NOT use aerosol can of starting aid on tractors with the thermostat connected to the electrical system.
Ether combined with thermostat can cause an explosion with damage to engine, personal injury or both.
Handle starting fluid correctly. Starting fluid must only be used when an ether start aid is fitted as original equipment by the manufacturer or when installed by a
Dealer as an accessory, in case of tractors being fitted with glow plugs or thermostat ,this must be removed prior to the installation.
If aerosol cans of starting fluid are to be used the thermostat must be disconnected. Remove the wire from the thermostat unit which will be found on the induction manifold. Tape the end of wire to prevent an electrical short circuit.
Before starting the tractor, ensure that no persons or hindrances are present in its range.
P. SAFETY: WORK SAFETY
WARNING : An unbalanced tractor could overturn and cause injury or death. Make sure front frame counterweights, wheel weights and wheel ballast are used as recommended by the manufacturer. NEVER add extra counter weights to compensate for an overload, better to reduce the load.
WARNING : Keep all parts of your body inside the operator's compartment while operating the tractor.
Q. Make the right moves
Make sure your tractor is ready for the job it must do. Know the rated load capacities of your tractor and never exceed them. Be certain that any equipment or implements you intend to use DO NOT exceed the load rating of your tractor. Be sure the tractor and implement PTO rev/min match.
Keep in mind that tractors normally operate on uneven, unpaved, and often bumpy or sloping surfaces. Operating conditions can reduce the amount of weight you should carry or
WARNING: Do not start the tractor without ensuring a perfect command of speed and
pull.
steering controls
Operator Manual
R. Follow safe operating practices:
Before starting, inspect the work area to establish the best and safest procedure. Plan your work so that you steering wheel or other controls.
drive as straight as possible forward. Beware of
F
grip on the steering wheel at all times, with the ponds etc. Watch for any possibly dangerous thumbs clear the spokes when driving the tractor.
F
implements or implements with high components, the operator's seat.
the PTO, lower all attachments and implements to the ground, place the tractor in neutral, engage parking brake, shut off the engine and remove the key.
DO NOT touch, lean on, or reach through any implement mechanism or permit others to do so.
Stay alert. Should something break, come loose, or fail to operate in your equipment, stop work, shut off the engine, inspect the machine and have repairs or adjustments made before resuming operation.
S. Watch out for others
Be aware of what is going on. Never allow an untrained or unqualified person to operate your tractor. They could injure themselves or someone else.
WARNING: Your tractor is a one person machine. DO NOT permit others to ride on the tractor or the implement . In some countries a passenger seat must be fitted to carry passengers. Never allow anyone to ride on the implements or other equipment including trailers, except on certain harvesting equipment, specially designed for riders during the actual harvest operation only (not during transport). Such equipment must have provision for a safe riding area. NEVER allow children on a tractor.
WARNING: Accidental contact with high- voltage, lines cause death. In case of contact with high -voltage conductors DO NOT leave the tractor, bid move the tractor and/or the loader in such a way as to eliminate the contact and reach a safe distance
WARNING: Be certain you can control both speed and direction before moving. Move slowly until you are sure that everything is operating properly. After starting, recheck the steering, right and left. Be certain you have full steering and brake control. If differential is locked, DO NOT operate at high speed or turn the tractor until the differential lock is disengaged.
23
24
WARNING : Never lift a load over anyone
allow anyone to stand or pass under a raised implement in the bucket, get the appropriate attachment.
Never allow anyone to stand on the safety frame or fenders,.
starts, turns, or change of direction. Keep loads as near to the ground as possible.
of, under, or behind loaded or loading equipment.
Never drive a tractor up to someone standing in front of a fixed object.
hitches, drawbar, lift arm, PTO drive, cylinders, belts, pulleys, and other moving parts. Keep all shields and guards in place.
T. Risk of overturning
For your safety, it is recommended that all platform tractors are fitted with safety frame and seat belts
In the event of overturning with a tractor fitted with a safety frame, hold the steering wheel firmly and DO
NOT attempt to leave the seat until the tractor has come to rest.
U. To avoid side overturns:
for the job being done.
transport speeds.
the tractor is equipped with a front end loader, carry the bucket and load as low as possible.
let your tractor bounce. You may loose steering control.
could run away on the down slope or the tractor could jackknife around a towed load.
and gradually.
slow the tractor engine and use the same gear you would use to up the slope. Shift into gear before you start downhill.
four- wheel braking.
Operator Manual
WARNING : NEVER stand, or allow anyone else stand between the tractor and implement unless the engine is turned off parking brakes is engaged, the transmission is in neutral, and all attachments or implements are lowered to the ground.
Operator Manual
WARNING : NEVER disengage the clutch or attempt to shift gear after you have started downhill.
If it is necessary to cross a steep slope, avoid turning uphill, slope down and make a wide turn.
Travel directly up or down the slope, never across it.
When traveling up or down a slope, keep the heavy end of the tractor pointed uphill. steep slope rather than across it.
When traveling across a slope with side mounted implements, keep the implement on downhill side. Avoid any stumps rocks, bumps or the uphill side. Don't raise the implements, keep must do so, avoid any holes or depressions on the them as low to the ground as possible when crossing a slope.
downhill side. Avoid any stumps rocks, bumps or raised areas on the uphill side. When operating near ditches or banks, always keep your tractor behind the shear line .
Avoid crossing steep slopes if possible. If you must do so, avoid any holes or depressions on the downhill side. Avoid any stumps, rocks, bumps or raised areas on the uphill side.
ROCK
25
26
V. To avoid rear overturns
WARNING : Hitching to the rear axle, or any other point above the swinging drawbar, can cause a rear overturn.
DO NOT pull anything using the top link connection, or from any point above the centre line of the rear axle. Always use an approved drawbar, and only use a drawbar pin that locks into place.
High hitching can cause rear overturn, which may cause serious injury or death. Hitch loads to the drawbar only.
When using a three-point linkage drawbar, the stays must be fitted and kept in the down position.
Use front counterweights to increase tractor stability when towing a heavy load or to counter balance a heavy rear mounted implement
DO NOT overload your tractor and DO NOT ballast it beyond its carrying capacity. Never add ballast weight to counterbalance an overload. Reduce the load instead.
WARNING : An overload is always dangerous. Check the loading capacity of your tractor and NEVER overload
Operator Manual
Operator Manual
If the front end of the tractor starts to lift, reduce your speed and, if necessary, disengage the clutch .
If your tractor is bogged down in the mud or frozen to the ground, DO NOT attempt to drive forwards. The tractor can rotate around its rear wheels and overturn .Lift any attached implement and attempt to BACK OUT. If this is not possible, tow it out with another vehicle.
Start forward slowly and gradually increase your speed. DO NOT rev the engine or drop the clutch. If the tractor is attached to a heavy load, or immovable object, improper clutching may cause overturn
If you get stuck in a ditch, BACK OUT, if possible. If you must go forward, do it slowly, and carefully.
A bare tractor or a tractor with rear mounted attachments should be backed up the slope in reverse and travel forward downhill.
A tractor with a loaded front end bucket should be backed down the slope and travel forward uphill. Keep the loader bucket as low as possible.
Always keep the tractor in gear when going down hill Never permit the tractor to coast with clutch disengaged or transmission in neutral
27
28
Operator Manual
W. General operating hazards
Ensure that the PTO shield 1 is in plane and that the cap 2 is fitted when the PTO driveline is not in use
WARNING : NEVER attempt to unplug the hydraulic connections, or adjust an implement with the engine running or the
PTO drive in operation. To do so may result in serious injury or death.
Before attaching, detaching, cleaning or adjusting
PTO driven implements, disengage the PTO, stop the engine remove the key, and make sure that the PTO driveline has stopped.
Ensure that all the PTO driveline guards are in place and observe all safety signs .
When using chemicals, carefully follow the chemical manufacturer's instructions for use, storage and disposal. Also follow the chemical application equipment manufacturer's instructions.
Be sure everyone is clear of your machine before engaging the PTO. For stationary PTO operation, always place transmission in neutral, engage parking brake and lock both tractor and implement wheels.
When operating under poor visibility conditions, or in the dark, use your ground speed. (DO NOT use your field lights when traveling on a roadway because rear pointed white lights are illegal except when reversing and may confuse following drivers).
When operating mobile PTO driven equipment, never leave the tractor seat until the PTO drive is dis- engaged, the transmission is in neutral, the parking brake is engaged, the engine shut off and the key removed.
Operate your tractor with the wheels set the widest setting possible, consistent with the particular task you are performing. To adjust wheel settings refer to
Maintenance and Adjustment section.
DO NOT use PTO adaptors, reducers or extensions as they extend the PTO coupler and universal joint out beyond the protection offered by the PTO shield.
The top link rods must not be extended beyond the point where threads begin to show. Fig.
Reduce your speed when operating over rough or slippery ground when foliage restricts your view of hazards.
DO NOT make sharp turns at high speed.
1
2
Operator Manual
WARNING : A front-end loader (bucket or forks) must be equipped with a suitable restraining device to prevent the load, bales, fence posts, rolls of fence, wires etc.) from rolling down the lift arms into the operator's compartment and crushing the driver when the loader is raised.
Inadequately secured objects could also fall and injure bystanders. Do not use implements for different purpose or to handle materials they are not expected to . For the operation of front loaders and relative safety rules, please refer to the Operation Manual of the loader.
Threepoint hitch and side mounted implements make a much larger arc when turning that towed equipment.
Make certain to maintain sufficient clearance for safe turning.
When using attachments or implements with the tractor, be sure to thoroughly read the Operator
Instruction Book for that attachment or implement and follow its safety instructions.
Pull only from the approved drawbar. Towing or attaching to other locations may cause the tractor to overturn.
Improper use of the drawbar, even if correctly positioned, may cause the tractor to overturn to the back.
DO NOT overload an attachment or towed equipment
Use proper counterweights to maintain tractor stability.
Hitch loads to the drawbar only.
X. Road Transport
Before operating your tractor on a public road, a number of precautions must be taken.
Familiarize yourself - and comply - with all local bylaws, and national laws appropriate to your tractor.
Lock your brake pedals together.
Raise all implements to their transport position and lock them in place.
Place all implements into their narrowest transport configuration.
Disengage the PTO and differential lock.
Make sure tractor and equipment are equipped with slow moving vehicle (SMV) signs or beacon if the law requires them and that loads do not obscure themor other lights.
Make sure any required clearance flags or hazard lights are in place and in working order.
Make sure you use a proper hitch pin with a clip retainer.
Clean off all reflectors and road lights, front and rear, and be certain they are in working order.
Implements mounted on the 3-point hitch and mounted implements projecting from the side need a wider turn radius than trailed implements. Always be sure to keep enough clearance when making a turn.
40 km
40
Use the symbol valid in your country.
29
30
Operator Manual
Y. Road regulations Z. SAFETY-AFTER OPERATION
When operating your tractor on a public road a number of precautions must be taken.
WARNING : DO NOT allow any passengers on the tractor or towed equipment.
Know the route you are going to travel.
Use flashing lights or beacon when traveling on roads, day or night, unless prohibited by law .
When stopping at any time, bring the tractor to a secure halt (DO NOT park on a slope), apply the parking brake, engage the Park-Lock (if installed), disengage the PTO, place all gear shift levers in neutral, lower the implement to the ground, stop the engine and remove the key BEFORE leaving the seat.
Use caution when towing a load at transport speeds especially if the towed equipment is NOT equipped with brakes.
Observe all local or national regulations regarding the road speed of your tractor.
Use extreme caution when transporting on snowcovered or slippery roads.
Wait for traffic to clear before entering a public road.
Beware of blind intersections. Slow down until you have a clear view.
DO NOT attempt to pass at any intersection. Slow down for turns and curve disengaged or transmission in neutral.
kerb as possible.
let the road and let it go by.
might do.
normal and slow down gradually.
Operator Manual
AA. Risks deriving from exposure to noise:
Noise characteristics and measurement
Noise is a pressure variation in an elastic medium, generally the air, produced by the variation of a material body (source) that determines an undesired and often annoying acoustic sensation. Noise is mainly characterized by;
F
expresses the entity of the pressure variation due to the sound wave.
Measured in decibels (dB), It doubles the sound intensity and, thus, the energy that reaches the ear.
F
expresses the number of pressure variations of the wave per second and is measured in Hertz (Hz)- acute noises have high frequencies (2000-4000 Hz or more) while lowpitched noises have low frequencies (250 Hz or less).
F
The higher the sound level and exposure time, the greater the noise risk will be: this is a sound level measurement that takes into account noise fluctuations and the varying sensitivity of the ear to the frequencies: LAeq is measured with a sound: level meter; measurement that takes the various noise levels into account along with the time the worker remains on the individual machines or working at determined processes: PEL is calculated mathematically.
Noise pathologies
Damage to the hearing
Noise causes hyperdulia or deafness because it destroys the acoustic receptors, nervous cells able to transform the mechanical sound vibrations into nervous impulses that, on reaching the brain, determine the aural sensation. These receptors are irreplaceable if they are destroyed and the resulting damage is irreversible: hyperdulia worsens if exposure to noise continues and does not improve even if this terminates.
Moreover, it is also bilateral since it can be accompanied by annoying buzzing and whistling sounds, and by intolerance to loud noise.
The damage is insidious since it proceeds slowly and unexpectedly: in the initial phase, when it is limited to a diminished ability to perceive acute sounds (music, bells) or the spoken voice when there is a background noise, it can only be detected by means of an audiometric test. Pulsating noises of great intensity lasting a very short time are highly damaging since the ear is unable to actuate any physiological protective measures in time. Hyperdulia from noise generally arises after several years of exposure and depends on the PEL (risk almost null below 80 dBA) and on individual characteristics. It is an incurable disease: the only efficacious means of protection against it is prevention.
Other effects
Noise does not just determine aural sensation. For levels exceeding* 70dBA, it causes stress by means of the cerebral integration centers and determines a specific neurovegitative reaction responsible for effects that lead to cardio circulatory and gastro enteric diseases. Amongst these, it is worthwhile noting: an increase in gastric acidity, a decrease in the heart rate, visual range and reflex speed; a sensation of discomfort and weariness with an increased sense of fatigue.
These effects are dangerous because they also increase the risk of accidents.
Personal equipment to protect against noise
Individual protective equipment attenuates the sound energy transmitted to the ear through the air. This equipment is used when dangerous exposure cannot be avoided in any other way.
There are different types of devices with different attenuating capacities: helmets, ear muffs, ear plugs
Helmets and ear muffs offer the greatest protection but they are bulky and inconvenient to wear.
They are therefore only of use for exposure to high noise levels but for short periods of time (max. 2 hours).
Ear plugs are generally tolerated to a greater extent and are of particular use in the case of lengthy exposure to noise of a lesser intensity.
Always use adequate individual protective equipment to safeguard the hearing when the personal daily level of exposure to noise is 85 dBA or more. Consult the
"specifications" chapter of this manual in relation to tractor noise measured in instantaneous conditions in compliance with the laws in force.
31
32
4
3
9
POSITION OF DECALS ON TRACTOR
6
Operator Manual
7
2
1
5
Operator Manual
1.
SAFETY INSTRUCTION
It is essential to read The Manual carefully.
Do not take off belt or Adjustment while Tractor is Running.
Do not dismantle or assemble from the Tractor while is in motion except in an emergency.
Do not stand in-between the Tractor and Equipment when operating control.
Keep clothing hand and feet away from moving parts.
Do not make any adjustment when tractor is in operation.
Wear adequate Footwear and snug-fitting clothing.
Do not sit or stand on unsafe place when Tractor is moving.
Keep Display Boards, Handles and Drivers Position Clean.
Keep All Safety Guards in place While working.
Make sure that no trains are coming before crossing the unguarded railway crossing.
PART No. 20002577
2.
DO NOT OPERATE
UNTIL YOU READ THE
OPERATOR'S MANUAL
TO UNDERSTAND
THE IMPORTANT
FUNCTIONS AND
CONTROLS.
3.
FOLLOW THE GENERAL
INSTRUCTIONS AND ROUTINE
MAINTENANCE AS GIVEN
IN THE MANUAL
4.
FASTEN
SEAT BELT
SEAT BELT MUST BE
WORN BECAUSE THIS
TRACTOR IS EQUIPPED
WITH ROLL OVER
PROTECTION.
FAILURE TO FASTEN SEAT BELT COULD
RESULT IN SERIOUS INJURY OR DEATH.
5.
PULL ONLY FROM DRAWBAR. PULLING FROM ANY
OTHER POINT CAN CAUSE REAR OVERTURN.
DO NOT OPERATE THE PTO WITHOUT GUARD.
USE SAFETY CHAIN WHEN TOWING EQUIPMENT.
FAILURE TO FOLLOW ANY OF THE ABOVE
INSTRUCTIONS, CAN RESULT IN SERIOUS INJURY
TO OPERATOR OR OTHER PERSON.
33
6.
7.
8.
34
9
Operator Manual
KEEP FLAMES AWAY
FROM BATTERY.
DISCONNECT CABLE
OF BATTERY BEFORE ANY
WELDING OPERATION.
PROTECT YOURSELF FROM
BATTERY, FLAME BURNS
CAN RESULT FROM
BATTERY ACID.
IN CASE OF CONTACT WITH
ACID, FLUSH WITH PLENTY
OF WATER IMMEDIATELY.
DO NOT JUMP START THE
TRACTOR BY SHORTING
ACROSS STARTER
TERMINALS, TRACTOR
WILL MOVE IF IN GEAR.
READ THE OPERATING MANUAL
CAREFULLY BEFORE STARTING THE
TRACTOR. FOR QUERIES CONTACT
AUTHORIZED DEALER.
CLEAR THE AREA OF BYSTANDERS.
UNDERSTAND OPERATION AND
LOCATION OF CONTROLS.
START ENGINE ONLY FROM DRIVER
SEAT WITH GEAR LEVER IN NEUTRAL
POSITION BY PRESSING CLUTCH
PEDAL.
WHILE DRIVING ON ROAD, BRAKE
PEDALS SHOULD BE LOCKED
TOGETHER, USE SLOW MOVING
VEHICLE EMBLEM AND WARNING
LIGHTS.
DO NOT LEAVE THE ENGINE RUNNING
IN CLOSED CONDITIONS.
WARNING
DO NOT USE DIFFERENTIAL LOCK ON
ROAD AND BEND, USE IT ON SLIPPERY
SURFACES.
DO NOT RUN FAST ON ROUGH GROUND,
TURNS AND SLOPES TO AVOID JERKS.
SITTING IS PROHIBITED ON FENDERS IF
THERE IS NO SPECIFIC SEAT PROVIDED.
DISENGAGE PTO AND STOP ENGINE
BEFORE ATTACHING OR DETACHING
IMPLEMENTS.
BEFORE LEAVING THE TRACTOR SEAT,
LOWER THE EQUIPMENT, POSITION GEAR
LEVER IN NEUTRAL, STOP ENGINE AND
APPLY PARKING BRAKE.
KEEP CLOTHING
AND HANDS
AWAY FROM
BELTS AND
FAN TO AVOID
SERIOUS
INJURY.
COOLING SYSTEM
REMAINS UNDER
PRESSURE.
DO NOT REMOVE
RADIATOR CAP
WHEN SYSTEM IS
HOT.
ALWAYS TURN
THE CAP SLOWLY
AND ALLOW
PRESSURE TO
ESCAPE BEFORE
REMOVING THE
CAP COMPLETELY.
WHEN OPERATING
BELOW 32°F, USE
SUITABLE
ANTIFREEZE WITH
WATER.
Operator Manual
ROAD SAFETY SIGN
Right Hand
Curve
Left Hand
Curve
Right Hair Pin
Bend
Left Hair Pin
Bend
Narrow
Bridge
Pedestrian
Crossing
School Ahead Men at Work Cross Road Gap in
Median
Side Road
Right
Side Road
Left
Staggered
Intersection
No Stopping or Standing
Staggered
Intersection
No Parking
Staggered
Intersection
Major Road
Ahead
Right Reverse
Bend
Left Reverse
Bend
Narrow Road
Ahead
Road Widens
Ahead
Cattle Ferry One way signs
Vehicles Prohibited in
One Direction
One way signs
Vehicles Prohibited in
One Direction
Y-Intersection Y-Intersection
Y-Intersection T-Intersection
Straight
Prohibited or No Entry
Right Turn
Prohibited
Left Turn
Prohibited
U-turn
Prohibited
35
1. INSTRUMENT PANEL, ELECTRICAL CONTROLS AND SHEET METAL
L - FOUR WHEEL DRIVE INDICATOR
F - TRAILOR INDICATOR 1
H - CLOGGING INDICATOR
E - BATTERY INDICATOR
D - FUEL GAUGE
B - OIL PRESSURE GAUGE
N - LEFT SIDE INDICATOR
C - RPM-CUM-HOUR-METER
O - RIGHT SIDE INDICATOR
A - TEMPERATURE GAUGE
J - VOLT METER
M - TRAILOR INDICATOR
I - HAZARD SWITCH
Q - HORN SWITCH
P - PARKING / HEAD LAMP SWITCH
R - SIDE INDICATOR SWITCH
A. TEMPERATURE GAUGE:
This gauge indicates temperature of engine coolant. GREEN zone indicates normal temperature and RED Zone indicates engine overheating. If the needle moves beyond normal range, towards RED zone, follow the procedure:
I Drive safely to the side of road and stop your tractor.
II Allow the engine to run idle.
III If the temperature does not go down, shut it off and allow sufficient time for it to cool.
IV Visually inspect the fan belt for looseness, breakage and all water hose connections for leak.
V If the fan belt is OK and no coolant leak is noticed, check the coolant level.
VI Add coolant if required.
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Boiling hot coolant and steam may blow out under pressure, which could cause serious injury.The cap should only be taken off when the coolant temperature has lowered. Necessary precaution to be taken while opening the radiator cap.
Green
B. OIL PRESSURE GAUGE
This gauge indicates pressure of lubricating oil in the engine. If the needle enters in RED zone, stop the engine and follow the procedure
I Stop your tractor to the side of road on leveled surface
II Wait for minimum 10 minutes after stopping the engine.
III Pull out the dipstick, wipe oil off with a clean cloth, insert & tighten the dipstick all the way into engine, and then remove it again. The oil on dipstick should be between the
UPPER and LOWER limits.
iV If the oil level is below the lower limit, then top up with oil.
V Start the engine, allow it to run idle and don't race it immediately.
Red
36
CAUTION
Do not operate the engine if there is no oil pressure indication.
Operator Manual
Red
Green
Operator Manual
C. RPM CUM HOUR METER
Needle of this meter indicates speed of engine in Revolution per minute and the recorder meter indicates number of hours clocked by the engine.
GREEN zone indicates economical speed.
Green
Red
D. FUEL GAUGE
Fuel gauge gives an approximate indication of the amount of fuel in fuel tank. If the needle enters in RED zone, refill the fuel tank.
Amber
Red
FUEL
Green
E. BATTERY CHARGE INDICATOR
If the indicator glow, it means that battery is not being charged. If the indicator remains
'OFF' battery is being charged.
F. TRAILER INDICATOR-1
It indicates the working of left side trailer indicator & will work if auxiliary trailer is hitched & electrical connection is made with auxiliary electrical socket.
G. MOBILE CHARGER POINT
This point is provided to charge the mobile phone.
37
H. CLOGGING SENSOR INDICATOR
This light will glow when the air filter get choked. Clean the cleaner immediately it this light visible.
I.
HAZARD LIGHT SWITCH
Pressing this switch will turn on all four indicator lights. To be used if tractor is stopped on the road or if some breakdown if there.
J. VOLTMETER
It shows the voltage of battery.
K. HIGH BEAM
It glows when high beam of head light is used.
L. FOUR WHEEL DRIVE INDICATOR (OPTIONAL)
It indicates the engagement of 4WD if equipped
38
Operator Manual
Operator Manual
M. TRAILER INDICATOR-2 TURN
It indicates the working of right side trailer indicator.
N. LEFT SIDE INDICATOR
It glows when left side indicator is switched ON.
O. RIGHT SIDE INDICATOR
It glows when right side indicator is switched ON.
P. PARKING / HEAD LAMP SWITCH
This switch is provided to switch 'ON' or' OFF' the parking lights & head light of the tractor.
P
Q. HORN SWITCH
The switch is used for blowing the horn
Q
39
Operator Manual
R. SIDE INDICATOR SWITCH
This switch is used for indicating vehicle turn either left or right. Toggle the switch(R) left or right for respective indication.
R
1.2 ELECTRICAL CONTROLS (WITH COMBINATION SWITCH)
1. Starting key switch.
2. Hazard light switch.
3. Engine Stop knob.
4. Combination switch.
5. Fuse Box.
1I.
STARTING KEY SWITCH:
Insert the key into the starting switch and rotate it in clockwise direction until engine starts. Do not keep the starter engaged for more than ten second. If engine stalls & falters in starting, wait 5 to 10 seconds before re-enganging the starter, otherwise you may damage it. Refer Page No. 22 for cold starting instruction for starting engine in cold weather.
2.
HAZARD LIGHT SWITCH:
push this switch to blink all indicators in hazard situation to alert Purpose of the hazard switch is as follows.
1. All the four lights blinking Indicates that driver has no control on tractor.
2 Mechanical defects in the tractor.
3. The driver is in distress maybe calling for a help or coming vehicle should take care of it self.
3. ENGINE STOP KNOB:
To stop the engine release the accelerator lever and pull the stopping knob. After stopping the engine push it back to its original position.
4.
COMBINATION SWITCH
R. SIDE INDICATOR SWITCH:
This switch is used for indicating the vehicle turn. Move turn signal lever left to indicate left (L) hand turn or right (R) for right hand turn. Indicator lights n hour meter will flash according.
Q.
HORN SWITCH:
This switch is used for blowing the horn.
P.
HEAD LIGHT AND PARKING LIGHT SWITCH:
This switch has four positions in clockwise direction.
1st position : All lights are off.
2nd position (clockwise) : Parking lights, Instrument panel lights, tail lights will glow.
3rd position (clockwise)
4th position (clockwise)
: Head lights (low beam), Instrument panel lights, Parking lights, tail light will glow.
: Head lights (High beam) Instrument panel lights, Parking lights, tail light will glow.
V. FUSE BOX:
Fuse box is mounted on the dashboard. Remove the cover of fuse box by pressing the fuse box in lateral direction, as it will come of from locking clamp . Replace the fuse whichever need replacement (Never install a wire instead of proper fuse. Use only specified fuses) as mentioned on box.
4
2
P
3
R
L
1st
2nd
3rd
4th
R
1
Q
40
Operator Manual
1.3
PROCEDURE TO OPEN THE TOP HOOD
I.
Insert the key (1) and rotate it clock wise to unlock the bonnet lock, than lift the handle (2) to open the bonnet.
II.
Slightly lift the top hood upwards raising and it will raise of up by it sell with gas spring installed, to open it fully.
2 1
III.
Use stay rod as shown in fig. to keep the hood in open condition for prolonged duration, in case of any repair.
Stay Rod
1.4.
REAR VIEW MIRROR
Both side rear view mirror installed for better rear side visibility
Side view mirror
1.5.
COLD START UNIT
Cold start unit is fitted for ease in engine starting under cold weather.
Cold Start Unit
41
Operator Manual
2. ELECTRICAL EQUIPMENTS
2.1 BATTERY
12V, 88Ah
I. Battery Access
Battery is located in front of the radiator.
To gain access:
1. Raise the hood as per procedure to open the top hood refer page no. 41
II. Removing Battery
To avoid sparks, disconnect negative ( g r o und) cable first and connect it last.
CAUTION
1. Remove negative (ground) battery cable (B) and remove the cable connection. Then remove positive cable (A) and connection.
Loosen nuts securing battery hold-down and rotate the holder down, freeing the battery.
2. Lift and slide the battery from the battery tray.
III. Checking Battery Condition
a.
Battery gas can explode. Keep sparks and flames away from batteries. Use a flashlight to check battery electrolyte level.
b.
Never check battery charge by placing a metal object across the posts. Use a voltmeter or hydrometer.
c.
Always remove grounded (—) battery clamp first and replace it last.
Charging Battery
Keep battery fully charged, especially during cold weather.
42
CAUTION
1. With charger off, attach positive battery charger lead to positive (+) battery terminal (A). Attach negative charger lead to tractor frame away from the battery.
2. Turn charger on and recharge the battery following battery manufacturer’s instructions for using charger.
Check battery condition as described below.
3. To disconnect battery charger, turn charger off.
Remove negative charger lead first, follow by positive charger lead.
A—Positive (+) Cable Nut
B—Negative (—) Cable Nut
A—Positive (+) Battery Terminal
B—Negative (—) Battery Terminal
Operator Manual
Servicing Battery
(A and B) clean and tight. To remove a n y c o rrosion, wash terminals with a solution of four p a r t s water to one part baking soda.
CAUTION
To avoid sparks, connect negative
( g r o und) (—) cable last and disconnect it first.
ground on tractor frame.
splashed into eyes.
CAUTION
Avoid the hazard by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
4. Avoiding spilling or dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
1. Flush your skin with water.
If acid is swallowed:
1. Do not induce vomiting.
3. Get medical attention immediately.
IMPORTANT:
DO NOT add water in freezing weather unless tractor will be run at least 30 minutes to assure thorough mixing.
3. Check level of electrolyte in each cell (A) at least every
250 hours. If low, fill to bottom of filler necks with
CLEAN, SOFT water. DO NOT OVERFILL.
4. Coat terminals with a small amount of grease.
A
A- Battery Cells
43
Operator Manual
2.2 ALTERNATOR
Alternator generate current which charges battery for healthy electrical backup. Rating:
12V, 36KW
I.
ADJUSTMENT
To adjust the fan belt tension loosen the nuts (A) and (B). Move the alternator outwards to obtain proper belt tension then re-tighten the nuts (A & B)
Always do routine check for fan belt tension as per service schedule refer page no. 72
Drive belt deflection
New Old
9-10 mm 10-11 mm
Alternator
Deflection
2.3 STARTER MOTOR
The starting motor rotates the flywheel for engine starting.
Capacity and Rating: 12V, 2.7KW
l
2.4 GENERAL MAINTENANCE OF ELECTRICAL SYSTEM
Never Patch up the electrical circuits.
Never replace a blown fuse by a higher capacity fuse. It could cause a fire.
Never work on components such as the alternator or starter motor when the engine is running.
Lastly when you are cleaning the tractor and using high-pressure spray, take care not to damage the connections on the various electrical cable.
2.4.1 PRECAUTIONS BEFORE CONNECTING WELDING APPARATUS:
In case of any electrical welding on tractor, first disconnect battery earth connection.
44
Operator Manual
3. ENGINE
3.1 STARTING THE ENGINE
I.
STARTING ENGINE IN HOT WEATHER
Ensure Gear levers at neutral Position.
Ensure hand throttle lever is at low idle position.
Press the clutch pedal and turn the starting switch clockwise to start the engine. Do not crank the starter motor more than 10 second.
Ensure that all gauges on dash board are working.
Note: The tractor is equipped with neutral safety switch . The tractor will not start if gear is not in neutral position.
II.
STARTING ENGINE IN COLD WEATHER
Ensure Gear levers at neutral Position.
To start the tractor after long period, pump the fuel feed pump up to 20 times before attempt to start.
To start , keep hand throttle lever in low idle position and rotate the key just before cranking position for 10 sec and then further rotates the key to start the engine. This will turn on the cold starter flame glow device installed on air intake manifold & heat up the air coming inside the engine cylinder .
If engine does not start, repeat the procedure after 2-3 minutes of interval.
When the engine started, keep hand throttle lever in its original position and check for water temperature, pressure gauge are in normal condition.
Tractor cooling system is based on pressurized cooling. Hence without radiator cap do not run the engine.
Do not cover radiator in cold weather.
3.2 STOPPING THE ENGINE
Let the engine run on idling for 1 or 2 minutes then pull the fuel cut off lever till engine stops.
3.3 RUNNING IN ENGINE
During initial 50 hours, follow all instruction to get effective and trouble free long life of tractor.
Don't put load when engine is cold.
Don't over load the engine.
I.
OPERATING TEMPERATURE
Run the engine at half speed for 10 minutes to attain normal operating temperature. The engine is designed to operate constantly at near full load. Put the Load an the engine only after maintaining operating temperature, (needle in green zone).
NOTE :
Avoid running your engine for long periods in idle mode (greater than 20-30 minutes).
45
Operator Manual
3.4 FUEL SYSTEM
I.
FUEL SAVING TIPS
Maintain your tractor. Badly maintained tractor waster 25% of precious fuel
Always top up tank at the end of day to avoid water contamination in fuel tank due to moisture.
Change fuel filter regularly as per maintenance schedule. Use genuine fuel filter available at authorized dealer. Also clean feed pump, filter and drain out water from filters as per schedule.
Prevent fuel leakage.
For better performance of tractor follow running in process mentioned in this manual.
Do not over ride the clutch.
Run tractor with appropriate speed and gear combination.
Do lengthwise field operation.
Always keep the specified tyre pressure for road and field operation.
Switch off the engine when the tractor is not in use.
Avoid wheel slippage
Attached tractor trolley at appropriate height.
Do not over load tractor beyond capacity
3.5 ENGINE LUBRICATION SYSTEM
We recommend the grade SAE20W/40
(Sonalika Maxima Engine Oil)
of as mentioned in service schedule
For Better Engine life use only
A
3.6 GENERAL MAINTENANCE
I.
CHECK ENGINE OIL LEVEL
Before checking the oil level,ensure that tractor is parked on leveled ground. Stop the engine and wait for some time, as all oil should return to oil sump.
Check the oil level by unscrewing dipstick (A) Top up the oil level if the level is below the minimum level(1) mark. Do not over fill than maximum level(2) mark.
II. Fuel System Components
D
A
F
I
H
J
E
C
G
K
B
46
A—Fuel filter Assembly
B—Primary Filter
D—Bleeding Screws-2 nos
E—Sediment Drain Screws-2 Nos
F—Fuel Injection Lines
G—Fuel Line to Pump
H F l li
I—Hand Priming Pump
J— Fuel Shut Off Lever
K—
Acclerator
2
1
Operator Manual
III. Replace Fuel Filter Elements
1. Remove cap screw (A) and filter element bowl (B).
2. Take out filter element (C).
3. Drain the fuel and clean the bowl.
4. Install new filter element .
6. Bleed the system from bleed screw (E).
IMPORTANT:
Change primary and secondary filter filter use new O-ring which comes filter elements
A—Cap Screw
B—Filter Element Bowl
C—Filter element
D—Washer
E—Bleed Screw
IV. Bleeding Fuel System
1. Loosen fuel return line (A).
2. Unscrew hand primer (B) on fuel supply pump until it can be pulled by hand.
4. Simultaneously stroke the hand primer down and close the fuel return port. This prevents air from entering the system. Tighten securely.
5. Lock hand primer in position.
V. Bleed Fuel System At Fuel Injection Nozzles
If engine will not start after the bleeding procedures described above, continue as follows:
1. Place throttle lever in fast idle position.
2. Using two open-end wrenches, loosen fuel line on at least three nozzles.
3. Turn over engine with starter motor until fuel flows free from bubbles out of loosened fuel nozzle connections.
Retighten connections.
B
A
A-Fuel Return Line
B-Hand Primer
47
Operator Manual
VI. Water Separator Bowl
1. The water separator is used to obtain the better
functioning of fuel system
2. Drain water and contaminants from clear water
separator sediment bowl by opening drain screw (C).
A-Water Separator
B-Indicator Ring
C-Drain Screw
48
Drain the water from drain screw, if the indicator ring floats up to the level as marked on the water separator (A).
CAUTION
VII. CLEANING OF FUEL FEED PUMP STRAINER
Shut off fuel cock for cleaning the strainer remove it from bowl by loosening the screw provided at bottom. Clean the element of strainer and fit it again. Be sure that part of strainer bowl is fitted properly. Any minor leakage in this may cause air trapping in fuel system.
VIII. CHANGING OF ENGINE OIL
Park the tractor on leveled surface. Warm up the engine up to operating temperature and shut down, drain the oil by removing the plug. Fit drain plug (A) and fill the clean oil through filter cap (B). Start the engine for a while. Wait for a while, check the dipstick oil level. Always keep oil level between maximum and minimum oil level.
At the time of oil pouring always avoid overflow condition from filter cap to do so use proper size of funnel..
Do not fill oil over the maximum oil level mark. It may cause excessive oil consumption.
3.7
AIR CLEANER
I.
GUIDELINES FOR DRY AIR CLEANER
Clean the primary element after every 300 hrs of operation or when ever choke indicator glows on dashboard.
Replace primary element after 3 cleaning or 900 hrs (whichever earlier).
Secondary element to be replaced after every three replacement of primary filter.
Use clean cloth to wipe sealing areas of primary filter.
Ensure proper seating of filter into housing before latching the cover. Do not use latches on the cover to force the filter into air cleaner that could cause damage to housing and will void the warranty.
B
Strainer Bowl
A
A
C
B
Operator Manual
II. Replace Air Cleaner Elements
1. Open the bonnet hood. Refer page No.20 for procedure to open the hood
2. Release clips (A).
3. Remove cover (B).
4. Remove primary element (C).
5. Clean out any dirt in canister taking care not to damage the secondary filter element.
IMPORTANT:
Remove secondary element (inner element) ONLY if it is to be replaced.
DO NOT attempt to clean secondary element.
If secondary element is replaced, install new element immediately to prevent dust from entering air intake system.
6. Removal of the secondary element (D) is similar to removal of the primary element.
NOTE:
When installing the air cleaner canister, make sure that the dust unloader valve (E) is facing down.
7. Install secondary element, primary element and cover.
A—Clips
B—Cover
C—Primary Element
D—Secondary Element
E — Unloader Valve
III. Cleaning Primary Element
1. Pat sides of element gently to loosen dirt. DO NOT tap element against a hard surface.
2. clean element with compressed air (below 690 kPa or
100 psi). Hold nozzle next to inner surface, and move up and down pleats.
IMPORTANT:
DO NOT direct air against outside of element, as it might force dirt through to inside.
3. Inspect element before reinstalling.
D
C
A
B
E
49
50
Operator Manual
IV. Inspecting Element
1. Hold a bright light (A) inside element (B) and check carefully for holes. Discard any element which shows the slightest hole.
2. Be sure outer screen is not dented. Vibration would quickly wear a hole in filter.
3. Be sure rubber sealing surfaces (C) are in good condition on both ends. If damaged, replace element.
A—Light Source
B—Element
C—Rubber Sealing Surface
It the tractor is utilized in the dusty condition the cleaning interval should be decreased accordingly .
CAUTION
3.8
RADIATOR
I.
COOLANT LEVEL IN RADIATOR (HOT)
Slowly unscrew the radiator cap up to the safety hatch (about 1/4 turn).
Wait to allow the steam to escape. Continue unscrewing the cap, press it down firmly to release the safety hatch. The level of coolant should just touch the tab located in the filling spout (E). If the level has dropped, check the entire cooling system for external leakage (radiator, hoses etc.) If there is no external leak, top up the coolant.
Important check :-
1. Check for coolant level (Cold) in recovery tank (C). It should be at cold
level as indicated on coolant recovery bottle.
2. Keep the radiator (B) topped up with coolant as per level up to filling
spout (E)
IMPORTANT :
Never pour cold water into the cooling system of a hot engine, as it
might crack cylinder block or head. Do NOT operator engine
without coolant for even a few minutes
A-Radiator Cap
B-Radiator
C-Coolant Recovery Tank
D-Upper Radiator Hose
E-Filling Spout
A
B
E
D C
HOT FULL
COLD FULL
Operator Manual
O
II.
ANTI FREEZING PRECAUTIONS (FOR COLD COUNTRIES) BELOW 0 C TEMP.
O
Precautions against damage by freezing should be taken if the engine is to be left exposed to temperature below 0 C either by adequately draining the water system or by addition of an anti-freeze solution of reputed make and incorporating suitable corrosion inhibitor. The coolant solution containing 40% anti-freeze in water in a properly maintained engine should maintain its anti-freeze and anti-corrosive properties through out the winter season and in general, a safe life of 12 months maybe reasonable expected.
When draining the water circulating system, it is not enough merely to open the radiator drain cock. The cap on the cylinder block must also be opened. This cap is on the rear side of the cylinder block where a pressurized radiator filler cap is fitted this should be removed before draining the cooling system. When draining the cooling system ensures that the engine is on level. When the engine is drained, in the majority of applications the water pump is also drained, but rotation of the pumping may be prevented by locking of the impeller by ice due to the pump drain hole being locked by sediment and or by locking of the seal through the freezing of moisture
0 between the seal and gland. clean & check the same. 40% antifreeze should be used up to -20 C ambient temperature. Please use below mentioned antifreeze mixing ratio according to ambient temperature.
% Vol of Antifreeze
Freezing Point
10
-3
20
-9
30
-18
40
-25
50
-37
III.
PRECAUTIONS TO BE TAKE WHILE WORKING BELOW FREEZING POINT.
Before starting the engine, turn the fan and water pump by hand this will indicate if freezing has taken place. This should free of any ice formation. If it is impossible to turn the pump by hand, the radiator and engine should be filled with warm water. After the anti-freeze solution has been used, the cooling system should be thoroughly flushed in accordance with the manufacturer's precautions before refilling the normal coolant.
IV.
RADIATOR DRAINING (When Cold)
Drain the radiator by unscrewing the drain plug of radiator and hose pipe connections must be removed before draining.
Drain Plug
51
Operator Manual
4. CONTROLS
4. CONTROLS
4.1 HAND CONTROLS
I.
GEAR SHIFTER LEVERS a.
MAIN GEAR SHIFTER LEVER
In transmission 8-forward and 2- reverse gears are available. Main gear lever (A) allows changing gear while tractor is moving. Release accelerator pedal and declutch. Select required gear, release the clutch progressively and accelerate the engine. Before changing the tractor movement from forward to reverse or reverse to forward direction wait for the tractor to stop.
b. HIGH-LOW LEVER
This lever (B) is used to change the low speed into high speed or vice versa when tractor is moving. According to requirement you can use it with combination with main gear lever. Move the lever forward for high gear & vice verse for low gear speed.
NOTE
: When traveling downhill always remain in gear. Never declutch. The gear selected should be same as would be used to Climb. For engaging / disengaging gear always depress the clutch. Always use low gear while moving down slope.
II.
PARKING BRAKE
Parking brake lever is mounted at left hand side of the driver (as per different models).
By pulling it upwards, you can apply parking brake to your tractor. It is used while your tractor is in parking condition.
Main Gear
Lever Knob
A
Side Gear
B
Hi-Low
Lever Knob
Before driving tractor, parking brake should be released.
CAUTION
III.
HAND THROTTLE LEVER
Hand throttle lever mounted on dashboard (Panel) is used in field application. To increase the speed of engine, pull down the lever and to decrease pull up the lever.
CAUTION
Never use hand throttle while driving the tractor on road use foot accelerator only.
IV.
4WD ENGAGE & DISENGAGE LEVER
Shift 4WD engage & disengage lever backward for 2 Wheel Drive (2WD) option & forward for 4 Wheel Drive (4WD) Option.
Panel Mounted
V. POWER TAKE OFF
Power take off is mounted at rear side of tractor. This is used for supplying rotary power directly to implement from engine. Power take off shaft has standard 06 Spline on
540rpm. PTO can be engaged or disengaged by PTO shifter lever.
52
Operator Manual a. POWERTAKE OFF SHIFTER LEVER
There are two positions for PTO lever. One Position is Neutral and Other position is
Live PTO. When PTO lever is engaged in backward direction it is called Live or Direct
PTO.
In Live or Direct PTO the speed directly depend on engine speed.
For engaging PTO set the engine to idle speed, declutch the engine and pull the lever to backward for direct PTO
540 RPM Obtained at 1600 Engine RPM
NOTE:
When the PTO is not being used put the PTO in neutral.
b.. OPERATION WITH PTO
To mount PTO driven implements following steps are followed.
a.
Be sure that both gear shifter levers are in neutral position and PTO lever is also in neutral position.
b.
Stop the engine, hitch or mount the implement on three-point linkage.
c.
Remove PTO shaft cap and keep it to toolbox. Join the implement with PTO shaft directly or with the help of carden shaft as per provision of implement. Follow the instruction of implement manufacturer
CAUTION
implement. For repairing or cleaning stop the engine and wait till the implement stop rotating. Do not pass between tractors and implement.
speed and then release clutch pedal slowly.
the four wheel.
VI. DRIVER SEAT
Driver seat can be adjusted according to your conveyance in following ways.
a. TRAVEL ADJUSTMENT
l
By Pulling up the lever A (Located under the driver Seat) the driver Seat can be slided and adjusted according to requirement.
By unscrewing the two knobs (R) and loosening the bolt (C) the crive seat can be moved up and down.
b.
SUSPENSION WEIGHT ADJUSTMENT
The Seat can be adjusted for better suspension according to driver weight. This can be done by knob as shown. If you want hard suspension turn the knob (1) clockwise and if you want soft suspension turn it to anti clockwise. When the indicator (2) indicates the weight (approx. your weight) then the adjustment of suspension setting is at best position.
2
1
53
VII. HYDRAULIC LEVERS a.
POSITION CONTROL LEVER (A)
It is Black Colour handle located towards the driver side which enables raising or lowering the implement / lift. It is used when implement operation demands stable / fixed position e.g. carrying goods in a bucket attached on three point linkage.
b.
DRAFT CONTROL LEVER (B)
It is Red Colour handle locate towards right fender side which is used to control the draft of soil on implement. By controlling the draft, the implement and tractor can be prevented from overloading.
c.
EXTERNAL HYDRAULIC CONTROL LEVER (C & D)
Used to control the oil flow into the auxiliary hydraulic circuit, either single acting or double acting.
A
Operator Manual
B
C
D
VII. DIRECTION CONTROL VALVES (DCV)
The DCV equipped is operated by two lever. Lever "C" is controlling Double Acting
(DA) DCV and Lever "D" is controlling convertible Double Acting (DA) Single Acting
(SA) DCV. We can convert the Convertible DCV into Double Acting (DA) by tightening the converting screw and vice-versa for SA.
SA - Single Acting
DA - Double Acting
DA QRC
DA / SA QRC
Converting Screw
4.2 FOOT CONTROLS
I.
CLUTCH PEDAL
By depressing clutch pedal (C) the motion and power of engine will be disengage from gearbox. Releases the clutch pedal slowly for transfer the engine power to gearbox.
C
54
Operator Manual a.
METHOD TO CHECK CLUTCH PEDAL FREE PLAY
Press down the clutch pedal and measure the distance between the footrest and pad.
The distance should be 25 to 35 mm. If the distance is less than 25mm or higher than
35mm then get it adjusted. The adjustment can be down by the clutch pedal tie rod as it is having adjustable nut.
Adjusting Nut
WARNING
Do not keep foot on clutch pedal while tractor is in running condition. It may cause excessive wear of clutch and clutch fails before its lifetime.
II.
DIFFERENTIAL LOCK
The differential lock mechanically locks the rear axle shaft together so that both wheels are coupled together so that both wheels are coupled together. This is an important aid when operating in muddy conditions as it provides increased traction, reduces wheel slip and prevent tyre wear.
If a rear wheel starts to slip - Engage the Differential Lock.
To Engage the Differential Lock
1 Fully depress the clutch pedal.
2 Push down the differential lock pedal with your heel and this engages the differential lock pedal
3 Release the clutch pedal slowly, while maintaining foot pressure on the differential lock pedal
To Disengage the differential lock, release the pedal. If the lock fails to disengage steer slightly to either left or right.
Do not apply differential lock while tractor speed is more than 6 kmph on turning
Do not attempt to sheer the tractor with the differential lock in the engaged position.
CAUTION
55
Operator Manual
III.
FOOT BRAKE PEDALS (E)
Use independent brake in the field operations. In field you will turn more sharply by pressing brake pedal for the side wheel on the turn. The pedals must be locked for road use. Use the lock by sliding the lever (A) side ways.
E a.
METHOD TO CHECK BRAKES
Release the hand brake. Uncouple the two pedals
Press down the right hand pedal and measure the distance between the pads & footrest. The distance should be between 55-65mm
If the free play is less than 55mm or higher than 65mm then adjust the both hex nut on actuator tie rod until free play comes to 55 to 65 mm. Now, press down the left hand pedal. If the values are not equal with the right hand pedal then repeat the same procedure until values become equal.
A
NOTE:
Difference in the free play will lead to unbalanced brakes. the tractor can slew, in the event of violent braking. the wheel on Which the brakes are applied locks and the tyre wears out quickly. During Road Operations Both the brake Pedals should be locked.
IV.
FOOT ACCELERATOR (F)
Food accelerator is used for control the tractor speed as per requirement. Only use foot accelerator while moving on road.
4.3 Seven Pin Socket
7 Pin socket is attached for trailer connection as per following Connectors.
1. Earth
3. Left Indicator
2. Working light
4. Parking light
5. Right Indicator
7. For Extra Connection
6. Brake light
56
Operator Manual
5. HYDRAULIC
5.1
HYDRAULIC SYSTEM
In this tractor live hydraulic system is provided. In which hydraulic pump is driven by engine and mounted with timing gear of engine. As the engine run, the hydraulic pump also starts working. Transmission lubrication oil is coming with hydraulic oil. Hydraulic system senses the load on implement through draft sensor provided at top link
Mounting bracket of three- point linkage. You can operate position control, draft control or mixed control.
5.2
HYDRAULIC CONTROLS OPERATIONS
5.2.1 POSITION CONTROL OPERATION
Position control (A) is used to raise hold and lower three point linkage for mounted implements during tillage/field operation e.g. Mounted Disc Harrow, Seed Drill,
Rotavator, Disc Plough, Ripper etc., which works above the ground. Once the height of implement is set, position lever maintains it. Always use Position lever for transporting the implement. One adjustable locking knob is provided for maintaining the specific position.
5.2.2 DRAFT CONTROL OPERATION
Automatic Draft Control(B) is designed to respond at the time of sudden resistance faced by the mounted dragging type implements i.e. Cultivator, Plough, and
Reversible Plough etc. while working in the field. Keep both position and draft lever(Black & Red) in lower most position (implement grounded) now move the draft lever (Red) towards up side position on sector as implement starts rising move back the lever by few mm.Prevents: Overloading of engine, breakage of implements, clutch slippage, tyre slippage, and excess fuel consumption.
5.2.3 MIXED CONTROL OPERATION
Simultaneous use of position control and draft control lever is called mix control. If the ground is not uniform and has soft areas where the implement can sink too deep then mix control is performed because in this situation draft control does not function properly. Use the same. Procedure as for work in draft control then draw a furrow up the field, when the ground becomes sandy, the implement tends to sink in deeply. In this case, bring the position control lever backward to limit the working depth. Now set the position lever in this position.
NOTE:
At the end of the furrow, bring the position lever backward to raise implement fully. To bring implement is working position lower the position lever to the previous position marked on the position sector by knob.
Always use position lever while joining the implement and transporting the implement.
During transportation while holding implement in raised position, always close the response valve to prevent any accident.
5.2.4
DIRECTION CONTROL VALVE OPERATION
This operation is performed when external hydraulic cylinders are operated by tractor.
To full the external cylinder shift the operating lever in forward and for draining the cylinder set the DCV Lever down in backward direction.
57
Operator Manual
5.2.5
RESPONSE VALVE
It acts as safely device during transportation of implements and helps in its smooth lowering. It is located on front end side of Hydraulic Rear Cover below driver seat.
Rotate anti clockwise to lock the hydraulic lift & rotate clockwise to control the lifting response time of lift.
CAUTION
Response Valve should always be closed during implements transportation.
5.3
THREE POINT LINKAGE
Three-point linkage is used for mount the implement, which is fully mounted, or semimounted and used for different field operation. Three-point linkage is controlled by hydraulic lever with the help of position and draft lever. In this two lower link are available, of which one side of the lower link is attached with differential housing and other is used to hitch the lower pin of the implement. Lift rods are mounted on lift arm that is operated through rockshaft. Right side lift rod is an adjustable for convenience to mount a implement in three point linkage. Loose side of Top link is used for attaching upper hitch pin of implement. Top link is adjustable for proper setting of implement and ease at the timing of joining.
5.3.1
LEFT LIFT ROD (A)
If lift rod is fitted with lift arm and lower link, the length of lift rod cannot be adjusted. For adjustment of length, remove the safety pin, which is attached with lift arm, and turn lift rod for increase or decrease the length.
5.3.2
RIGHT LIFT ROD (B)
For adjustment of length unlock the lever of -adjustment box and turn it clockwise for decreasing the length or turn it to anticlockwise for increasing the length.
5.3.3 TOP LINK (C)
For length adjustment of top link, fix the top link other end and turn the lever for increasing or decreasing the length. During field operation lock the tube to avoid unnecessary turning.
5.3.4 ROCKER LINK ASSEMBLY (D)
While using draft control, the sensing from top link to control valve is transferred by rocker link assembly. Three different mounting holes have been provided, for
C
A
C
G
B
E
B
1
2
3
Top Hole
Middle Hole
Bottom Hole
Soft Soil
Medium Soil
Hard Soil
58
Operator Manual
5.3.5
LOWER LINKS (E)
Lower Links are provided for hitching the implement.
5.3.6
STAY BARS (F)
Stay Bars controls the swing of implement during transport and field operations. Stay
Bar are provided between side of lower link and differential housing.
5.3.7
SWINGING DRAWBAR (G)
Swinging Drawbar fitted on rear side of the differential housing is used for trailer towing the haulage operation.
5.3.8 ATTACHING IMPLEMENT TO 3 POINT LINKAGE
Position the tractor to align corresponding linkage with the hitch points of implements.
Keep the implement on hard & leveled surface and attach as per given below instructions
First attach with Left Lift Rod (A)
Attach with Right Lift Rod (B)
Then at Last attach with Top Link (C)
5.4
GENERAL MAINTENANCE
5.4.1 TRANSMISSION/HYDRAULIC OIL LEVEL
Keep oil level up to maximum oil level mark.
5.4.2
HYDRAULIC OIL FILTER
Hydraulic oil filter is fitted at right hand side of tractor. Remove the old filter and change with new one dully filled with clean oil. Apply small amount of oil on rubber seal of filter and fit it. Do not over tight the filter.
5.4.3 CHECK TRANSMISSION OIL BREATHER
The breather is located on top of the rear cover, beneath the driver seat.
Remove the breather by unscrewing it. Clean it with diesel and check it for proper working and fit it again.
Oil Breather
NOTE:
Use proper genuine transmission oil.
59
Operator Manual
5.4.4
CHANGE TRANSMISSION OIL
Before draining the oil, heat up by running engine, transmission and hydraulic system. Park the engine on level ground, turn off the engine and then drain the oil by opening the drain plug provided at bottom of gear box and differential housing. Fill the new oil. Check the level by dipstick. Tighten the drain plug with torque of 90 NM.
5.4.5 CHANGE STEERING GEAR BOX OIL(MECH. STG. - OPTIONAL)
Drain out the oil by removing the drain plug of steering gear box assembly. Keep oil level up to level plug.
Steering oil capacity 600 ml (approx.)
5.4.6 POWER STEERING
Power stg consists of following components
A) Power stg oil tank
B) Dip stick cum breather
C) Power Stg. oil tank filter
Mechnical Steering Gear Level Screw
C
B
5.4.6.1 POWER STG OIL TANK
Steering oil in the power steering system is 3.5 lit. Resorvoir tank capacity 1.75 lit.
5.4.6.2
POWER STG. OIL TANK FILTER
Open the power stg. oil tank filter (C) by opening the locking screw. Clean the filter after every 150 hour .
A
5.4.6.3 POWER STG OIL LEVEL
Power steering tank oil level should be in "FULL" as Indicated in the dipstick.
Power stg oil tank full
Dip Stick Cum Breather
5.4.6.4
STICKER
Sticker provided in the steering tank in which power stg oil grade mentioned.
Recommended oil grade is DEXRON-IID
60
Operator Manual
6. WHEELS AND TYRES
Tyres play vital role in transportation and agriculture operations so their importance became a necessity tractor/ automobiles. Here we will discuss only pneumatic tyres.
On any tyre there is some marking which represents its size & capacity e.g. Tyre marking is
13.6x28, 12 ply rating i.e. 13.6 inch is the section width, 28 inch is the bead diameter. Ply rating doesn't show that the same No. of plies are inserted in tyre. It is only comparative measure of the load carrying capacity (L.C.C) of tyre. As more ply rating shows more L.C.C. at the same time as L.C.C. increases the shocks absorption capacity decreases.
l l
It is the most important factor in the efficient performance of tractor it should be used only as per company recommendation. In general, tractor is considered for two types of work:
Work on soft soil where maximum adhesion is needed. In this case there will be use of lowest pressure compatible with the load carried.
Work on hard ground and roads, towing etc; In this case there will be use of maximum pressure.
Overall Tread Width
Section Width
Tread Width
Tread Depth.
Rim Width
6.1
IN FIELD OPERATIONS
6.1.1
Correct Pressure
Good adherence by dirt grousers.
Good cleaning of the tread
6.1.2 Insufficient Pressure
Reduce adherence through lack of tyre grip.
Deterioration of tyre casing by traction forces.
6.1.3 Over Pressure
Reduce group due to lack of cleaning
Deterioration due to compacted ground.
61
Operator Manual
6.2
ON ROAD OPERATIONS
6.2.1
Correct Pressure
Resistance to Wear
6.2.2
Insufficient Pressure
Reduce through lack of tyre grip.
Deterioration of try casing by traction forces.
6.2.3
Over Pressure
Reduce grip due to lack of cleaning
Deterioration due to compacted ground.
NOTE:
Tyre pressure should never maximum pressure as recommended the tyre could burst. Change / repair any worn or faulty tyre
(cuts, cracks etc.) immediately to prevent the problem become more severe.
6.3 BALLASTING OF TRACTOR
Proper ballasting is an important factor in tractor performance. For better performance of tractor, the weight of tractor can be decreased or increased as per requirement.
Maximum productivity can be achieved only if tractor weight is appropriate for the job.
Ballast is required for traction and stability. Following factors determine amount of ballast.
I. FRONT END BALLASTING
Add extra removable weight to front end. Heavy pulling and heavy rear- mounted implements tends to lift front wheels. Add enough ballast to maintain steering control.
Six 31Kg. removable weights are already supplied with the tractor.
62
Operator Manual
II.
a.
b.
REAR END BALLASTING
WHEELS AND TYRES
Ballasting of rear wheel required for proper traction for heavy implements.
Ballasting can be done by water or cast iron weight. You can water ballast the Tyre up to 75%. It is most convenient way of ballasting. For the normal atmosphere region you can use ordinary water for ballasting. For tractors working in cole climate precautions must be taken to avoid the water freezing.
PRINCIPLE
The type inner tubes on the driving wheels are fitted with air and water valves to allow inflation with air and ballast with water. A special connections is required to connect the water supply to the valve or filling with 75% water (Air + Water) the set retains almost the same flexibility as when inflated with air only as the remaining spaces filled with air at the pressure normally used for the load carried and the size of tyre.
c.
Action:-
PROCESS OF WATER FILLING IN THE TYRE
1.
Jack up wheel & remove valve from the tube.
2.
Deflate the tube.
3.
Turn the wheel so that valve is on top/ 12 o' clock position.
4.
Attach the hose to the valve body by till it details flowing back means of a special adopter.
5.
Allow water to flow in.
6.
Fill water up to upper rim level.
7.
Take out the adopter and rotate the tyre to bring it to 11 o' clock position & replace the valve.
Allow water to flow out, and replace the valve. Bring in the tyre to 12 o'clock position again.
8.
Fill in air to its normal working pressure of 10-12 psi.
9.
Check the valve for proper tightness / leakage.
10. Remove the jack.
WATER
SPACE FOR AIR
VALVE BODY
AIR
*While filling water in tube it is said that water should be filled up to upper rim level i.e. 75% of its space, rest should be filled with air. Presence of air is necessary for cushioning effect and to absorb shock.
WATER INSIDE
PIPE FOR WATER FILLING
VENT TUBE
Chart shows water-ballasting capacity per Tyre.
TYRE SIZE WATER IN LITERS
13.6x28
180
NOTE:
Ballast should be limited by either Tyre capacity or tractor capacity. Each Tyre has a recommended load carrying capacity, which should not be exceeded. If a greater amount of weight is needed for traction then a larger. Tyre should be considered.
6.3.2.2
USING CAST IRON WEIGHT (REAR)
Cast iron weight are available in a 34 kg size. Weight can be installed on the outside of wheel. Use these weights as per recommendation. The tractor is already supplied with one set of casting rear weight.
6.3.2.2.1
INSTALLING CAST IRON WEIGHT
Cast iron weight can be attached to wheel by means of bolt. One or two weight can be attached. Tighten the bolts according to specified torque of 230 Nm.
63
Operator Manual
6.4
RECOMMENDED
LOAD CARRYING CAPACITY PER TYRE W.R.T ITS SIZE
Load Carrying Capacity in Kgs per Tyre at PSI (ON ROAD)
Tyre Size
13.6 x 28
Pressure
lbs/in 2
Ply Rating
6 Ply
8 ply & above
15
1100
17
1165
18
1220
19
1270
20
1325
22
1375
24
1430
25 26 27 29 31 33
1480 1530 1585 1645
NOTE :
Load can be increased by 20% without increasing inflation pressure if the tractor is operated at speed upto 16 Kmph.
FRONT TYRES
Tyre Size Pressure
Kg/CM
2 lbs/in
2
1.2
20
1.7
24
2.0
28
2.25
32
2.25
36
2.8
40
3.1
44
3.4
48
34
6.0 x 16 (2WD)
9.5x20 (4WD)
Load
Capacity
(kgs) per Type
340 380 415 450
850
485 515 545 570
6.5 TRACK WIDTH ADJUSTMENT
I. FRONT TRACK WIDTH (2WD)
For adjusting the front track wheel telescopic section is provided in hollow beam of the front axle. For adjustment on telescopic section four holes are provided at a distance of 50-mm. By this you can obtain three positions of track width and also the rims of front wheel offset. By reversing it you can adjust track width. Thus you can get 6-track width for front axle.
a.
FRONT WHEEL TOE IN
After setting the track width it is necessary to adjust toe in of the front axle.
64
Operator Manual b. CHECKING AND ADJUSTMENT OF TOE-IN
Firstly park the tractor on level surface. Turn the steering wheel so that front wheels are in the straight-ahead position. Stop the engine. Measure distance (A) between tyres at hub level in front of axle. Record measurement and mark the points on tyres. Move tractor back about 1 meter, so that mark on the tyre is at hub level behind the axle.
Again measure distance between tyres at same point on tyre. Record the measurement.
Determine the difference between front and rear measurement. If the front measurement is smaller toe is 'in'. If the rear is smaller, toe is 'out'. Distance (A) at front of tyres should be
3-6 mm less than distance measured at rear of tyres.
Adjust toe-in if necessary. For adjusting toe-in loosen the lock nuts (B) on both sides. Turn the tie rod (C) and adjust toe in to 3-6 mm. After adjusting torque the lock nut (B) to 100 NM.
B
C
NOTE:
If toe in of the front wheel is not proper, wear out of front wheel will Increase.
6.5.2
6.5.2 .1
REAR WHEEL TRACK WIDTH ADJUSTMENT
Track width of the rear axle can be adjusted by repositioning or exchanging the rims or by reversing the wheel discs.Track width can also be adjusted by exchanging the complete wheel to the opposite side of tractor. This maneuver permits the change from disc dished in to disc dished out operations without disassembling the wheel. When changing rear wheels from one side to the other, the arrow on sidewall of tyre points in the direction of forward rotation. A study of following diagram, from attempting to change track width setting will save unnecessary labour.
WHEEL BODY TOWARDS INSIDE
VALUE OUTSIDE VALUE INSIDE
SPACERS INSIDE SPACERS OUTSIDE SPACERS INSIDE SPACERS OUTSIDE
65
VALUE INSIDE
Operator Manual
6.5.2 .2
WHEEL BODY TOWARDSOUTSIDE
VALUE OUTSIDE
SPACERS INSIDE SPACERS OUTSIDE
TRACTOR SIDE
Rear
Front (2WD)
Front (4WD)
MAXIMUM
1814
1675
1530
SPACERS INSIDE SPACERS OUTSIDE
TRACK WIDTH (mm)
MINIMUM
1420
1290
1530
STANDARD
1420
1310
1530
NOTE:
Track widths are measured at bottom of centerline Some combinations not possible due to fouling with fenders.
6.6.
TIPS FOR PROPER HANDLING AND DURABILITY OF TYRES
Some ignorance and improper handling reduce the life span of tyres. In this topic we mention about the tractor that are account for proper handling and more durability of tyres. There are some factors that are mention as follow.
66
Operator Manual
Problems
Alternate wear tread
Factor Effecting Corrective action
road with two-tyre trailer.
to time. trailer.
Sidewall or
Shoulder damage
Scoop or wear from high center tread
Puncture of tyre again and again:
Damage to tread/crown of tyre
pieces of glass etc.
Cotton etc that are with sharp edges stem and deep roots have more probability to cause damage to tyre.
area.
crops with sharp edges stem and deep roots etc.
tread/crown area.
Damage of tyre due to less pressure
agricultural and transportation purpose.
adjust according to rows difference of crops.
edges areas.
tyres.
6.7
GENERAL SUGGESTIONS
6.8
CHECK WHEEL NUT BOLT
Check wheel nut of the front and rear wheel. Torque it as per specification.
67
7. FRONT AXLE 4WD (OPTIONAL)
7.1 FRONT AXLE 4WD
The tractor is equipped with front live axle (Optional) for better traction and pulling where even required. The live 4WD axle is having a limited slip differential with final epicyclic hub reduction for durability. The 4WD engagement can be done by mechanical actuation of lever located on the lift side of operator seat. Ensure proper oil levels in differential & hubs during routine maintenance check as also specified in service intervals.
a.
FILLING & REPLACING FRONT AXLE OIL
Align the hubs in horizontal position as marked on the hub (A) for filling & replacing front axle oil.
WARNING
Do not operate 4WD axle high speeds.
A
7.2
SWINGINING DRAW BAR
The tractor is equipped with swingining drawbar as conforming to ECE standard. Use correct position of bar i.e. it can be adjusted either telescopic way or can be tilted left on right. Remove the locking pins(1) to adjust the same.
CAUTION
For trail type implements alway use the swingining bar to hitch them.
7.3
Roll Over Protection
The objective of the frame is to protect the operator in the event of a roll over and they are designed to support the entire weight of the tractor in that event.
ROP frame is designed and has been tested to meet industry and or Government standards including ECE Norms.
Included in these tests were all mounting bases and bolts or other fasteners.
The ROPS frame has a fold down feature, which can be used to enter low buildings etc.
Take care when lowering the upper section of the ROPS frame and take extreme care while driving the tractor with the ROPS frame lowered.
Each ROPS has a separate serial no. Punch on the data plate which is affixed on the ropsframe as per ECE Norms.
1
Operator Manual
68
Operator Manual
7.4
Pneumatic trailer brakes (optional)
The tractor is equipped with Single line pneumatic brake system: i.e. when the braking is done via tractor service brakes, the air pressure in single line is cut off, the palm coupling end is connected to trailer end.
7.5 Pneumatic trailer brake components:
Compressor: -
The compressor is mounted on engine and is reciprocating type.
Shut down the compressor when you are not using the trailer in order to increase the efficiency of engine.
Unloader valve:
Unloader valve regulates the pressure in the system and maintains it at 8 bar.
CAUTION
Caution: Donot temper with unloader valve, get the pressure setting adjusted through authorized service centre or dealer only if there is any non-working of the valve.
Tank: -
Before draining the water content, park the tractor on level ground then drain the water contents by opening the drain plug provided at bottom of tank.
Line filter: -
Clean the filter depending on operating conditions - normally every 3 to 4 months. This requires taking the filter cartridge out and blowing it out with compressor air.
Donot over tight the filter replaced the damaged filter cartridge.
69
7.6
HYDRAULIC TRAILER BRAKE (If Equipped)
This is mounted on RH side of tractor in front of brake pedal. This is provided to operate the Hydraulic bakes of trailer. It is actuated by the braked pedals of the tractors.
The adjuster nut can be adjusted for sensitivity of the trailer valve.
7.7
HYDRAULIC TRAILER BRAKE FREE PLAY ADJUSTMENT
Adjust the Actuator adjustor in such a way ''that Actuator adjustor pin remain at lower side in slot of brake pedal and spherical pushing pin should remain in touch with Spool of Brake valve and finally fit split pin and plain washer after adjustment.
Note : During adjustment brake pedal should be in unoperating c o n d i t i o n a s w e l l a s t h e r e s h o u l d n o t b e a n y p r e s s u r e o n
Spool of Brake valve.
7.8
HYDRAULIC TRAILER BRAKE COUPLER
The Coupler is provided at the rear end of the tractor. The Trailer male Couple Should be attached at left side below seven pin socket with the female tractor coupler while the trailer is being towed on the road.
Operator Manual
70
CAUTION
Always de couple the hydraulic trailer brake coupler before unhitching the trailer.
Operator Manual
Gate valve: -
Turn off the gate valve when you are not using the trailer
Palm coupling: -
Make sure that the washer is clean and undamaged when connection is made. After that check the connection for proper seal.
Check points:-
Check out the air leakage at specific joints,if present contact your authorized service station.
Air leakage in braking circuit will lead to unbalanced brakes and tyres wears out quickly.
Note:-
Make sure that before operating the trailer brake runs the engine idle for at least 15 minutes. Unloading valve is used to set the required pressure do not temper with it, on finding some disturbance contact your authorized service station.
71
8.1
8. OTHERS
REGISTRATION PLATE
A vehicle registration plate, usually called license plate or number plate for official clentifical on purposes is mounted at the top of tail light of left/right side fender as per country rule.
8.2
LIGHTS
The vehicle is equipped with E marked front and rear tail lights.
8.3
REFLECTOR
A pair of rear tail reflections as per specification listed in the ECE standards.
8.4
EXHAUST MUFFLER
An under hood muffler with down ward/upward displacement exhaust pipe is fitted on the tractor.
8.5
HEAT INSULATION SHEET
The front hood is having a heat insulation/noise absorbing sheet fixed on the inner side of the bonnet for insulating the bonnet from the heat generated by engine.
72
Operator Manual
Operator Manual
8.6
PTO GUARD
For the operator safety the PTO is having guard with safety cover.
8.7
DRIVER SEAT (E MARK)
The operator seat conforms to the ECE standard and is having both horizontal as well as vertical adjustments. Further the safety belt is mounted on the seat.
73
Operator Manual
8.8
RECOMMENDED SCHEDULE FOR MAINTENANCE SERVICE
EVERY 10 50 MAINTENANCE INTERVAL (HRS)
SERVICE ITEM
GENERAL
COMPLETE WASHING
NIPPLE GREASING
COOLANT LEVEL & Top Up
AIR CLEANER
AIR CLEANER OIL
AIR CLEANER ELEMENT(WET)
AIR CLEANER ELEMENT(PRIMERY)
AIR CLEANER ELEMENT(SECONDARY)
AIR INTAKE HOSE CLAMPS
ENGINE
ENGINE VALVE CLEARANCE
ENGINE OIL
ENGINE OIL FILTER
ENGINE IDLE SPEED
FUEL INJECTION TIMING
BELL HOUSING NUT & BOLTS
COOLING SYSTEM
FAN BELT TENSION
COOLANT SYSTEM FLUSHING
CLUTCH
CLUTCH OPERATION &
PEDAL FREE PLAY
TRANSMISSION/HYDRAULIC
OPERATION OF GEARS
TRANSMISSION HYDRAULIC OIL
TRANSMISSION /
HYDRAULIC OILFILTER
HYDRAULIC OIL STRAINER
TRANSMISSION BREATHER
OPERATION OF LIFT
–
–
C
C
–
–
–
T
–
–
–
–
–
–
C
–
C
–
–
–
-
K
–
W
G
C&P
R
K
K
K
T
C&A
–
C&A
C
C
R
K
K
C
A
R
R
C
C
I
250
W
G
C&P
C&A
–
C&A
C
C
K
C
R
K
R
K
K
K
T
A
R
R
C
C
I
500
W
G
C&P
C&A
–
C&A
C
C
K
C
R
K
R
K
R
K
T
A
R
R
C
C
I
750
W
G
C&P
C&A
R
C
C
R
R
K
C
1000
W
G
C&P
C&A
–
C
C
R
K
K
C
1250
W
G
C&P
C&A
–
C&A C&A C&A
C
C
K
C
R
K
A
R
R
C
C
I
R
K
R
K
T
A
R
R
C
C
I
R
K
K
K
T
A
R
R
C
C
I
R
K
K
K
T
1500
C&A
K
C
R
R
C
C
W
G
C&P
A
R
R
C
C
I
R
K
R
K
T
C&A
R
74
Operator Manual
MAINTENANCE INTERVAL (HRS)
SERVICE ITEM
FUEL SYSTEM
PRIMARY FUEL FILTER
SECONDARY FUEL FILTER
FIP FEED PUMP BOWL
FUEL SEDIMANTOR
INJECTOR PRESSURE & SPRAY
BRAKES
BRAKE OPERATION & PEDAL
FREE PLAY
BRAKE HOUSING/LINING
STEERING
STEERING OPERATION
STEERING GEAR OIL LEVEL (MECH. & POWER STG.)
POWER STG. OIL TANK FILTER
POWER STG. OIL CHANGE
LINKAGES FOR PLAY
KING PIN
TOE IN
WHEELS &TYRES
WHEELS NUTS &BOLTS
TYRES INFLATION
FRONT & REAR AXLE
STUB AXLE GREASE
WHEEL BEARING GREASE
BATTERY
BATTERY ELECTROLYTE LEVEL
BATTERY TERMINAL GREASE
ELECTRICALS
FUNCTIONING OF OIL GAUGE
FUNTIONING OF
TEMPERATURE GAUGE
EVERY 10
C
C
–
–
–
–
–
–
–
C
–
–
–
–
–
K
D
–
–
–
C
–
50
C
K
C
C&P
R
R
C
C
C&A
C
C
T
C
K
D
–
–
–
G
G
C
G
250
C
C&P
K
–
C
C
C&A
C
C&P
K
–
C
C
C&A
G
G
C
G
C
C
T
C
K
D
–
R
–
C
K
500
G
G
C
G
C
C
T
C
K
D
–
–
R
C
K
750
C
C&P
K
–
C
C
C&A
C
C
T
C
K
D
C
R
–
C
K
G
G
C
G
LEGANDS
A : ADJUST
C : CHECK
K : CLEAN
R : REPLACE
D : DRAIN
G : GREASE
T : TIGHTEN
W : WASHING
Ü Engine Oil Grade should be selected as per operating Temperature condition
Ü Anti freeze should be used as per ambient temp.
Ü Clean Air cleaner eliment as and when required
P: TOP UP
1000
K
D
–
–
–
C
K
C
C&P
R
R
C
C
C&A
T
C
C
C
G
G
C
G
1250
K
D
–
R
–
T
C
C
C
G
G
C
G
C
K
C
C&P
K
–
C
C
C&A
1500
K
D
C
–
R
T
C
G
G
C
K
C
C&P
K
–
C
C
C&A
C
C
C
G
75
76
8.9 ELECTRICAL WIRING CIRCUIT DIAGRAM
Operator Manual
Operator Manual
8.10
RECOMMENDED GRADE OF LUBRICANTS & GREASES
TRACTOR MODEL
DRIVE
ENGINE OIL
QUANTITY (In Liters)
GRADE
MANUFACTURER
AIR CLEANER
BRAKES
MAIN BRAKE
HYDRAULIC SYSTEM
& TRANSMISSION OIL
QUANTITY (In Liters)
GRADE
VENDOR
GREASE
QUANTITY (In Kg.)
SOLIS 50
2WD/4WD
8.2
(Sonalika Maxima Engine Oil)
Recommend by ITL
61
ELF 2412
VALVOLINE / ELF
0.75
SAE 20W40
DRY AIR CLEANER WITH CLOGGING SENSOR
OIL IMMERSED BRAKE
0
NOTE :-
At level than gradient 18 , level of transmission oil should be increased by 5 ltr or as per requirement.
77
Operator Manual
8.11 GREASING POINTS ON TRACTOR
Center Pin (01pt.) Center Pin King Pin (Left / Right)
Front Wheel Hub (Left / Right) Tie Rod (02pt.) (Left / Right) Trumpet plate cover (left(01pt.)
Right (02pt.)
Steering Arm (Left) Steering Arm (Right) Lift rod (Left lift rod (01pt) &
Right Lift Rod (01pt.)
Clutch actuator shaft (left (01pt.) Right (01Pt.) Differential pedal (01pt.)
78
Brake Rod (05pt.) (Left) Brake Rod (05 pt.) (Right)
Operator Manual
9. WARRANTY POLICY
M/S International Tractor Limited, India warrant, subject as hereinafter provided that all new goods supplied by it are free from defects in material and workmanship. Its liability under such warranty being limited to making good any part or parts which shall within 42 Months from date of
Bill of lading or 36 Months from date of delivery to first original retail purchaser or 2000 Hours which ever is earlier, which includes 12 months or 1000
Hours on complete tractor & additional 24 months or 1000 Hours on power train (Engine, gearbox, transmission & hydraulics). Warranty for proprietary items will be up to 12 months or 1000 working hours whichever appears earlier from the date of delivery to the first original retail purchaser. Claims will be settled against manufacturing defects by ITL as per their published warranty policy.
(A) TERMS AND CONDITION:
ITL against their order and lodge the claim within 60 days from the date of repair of Tractor.
(B) EXCEPTIONS TO WARRANTY:
are in proper order because after that customer himself is responsible.
1000 working hours whichever appears earlier from date of sale to the original retail customer & shall be settled as per terms & conditions of the concerned manufacturer provided the repairable items have not been repaired from any other sources.
oil. o If tractor used overloaded, over heated, driver negligence, unauthorized modification, untimely servicing, poor maintenance or tractor met with an accident.
o Tractor has crossed the warranty period.
o In case of late submission of warranty claim. (The claim must be submitted within 60 days from the date of repair).
o If defective parts not available inspection. ITL can request parts within 90 days from date of submission of warranty claims.
.
· Warranty applicable only to first retail purchaser.
·
This policy ceases if the components show mishandling, modification, neglect of slight defect, overloading, overheating, poor maintenance or use of incorrect grade of oil.
·
The warranty becomes inoperative if the tractor is repaired/ dismantled in an unauthorized workshop and use of replacement parts, not supplied/approved by ITL.
·
ITL's responsibility is limited to the terms of the warranty and it shall not be answerable for personal injuries or consequential or resulting liability, damage or loss arising from any defects.
(C) - WARRANTY CLAIMS SUBMISSION: -
Authorized Distributor will submit the warranty claim form by filling all column duly signed & seal by Distributor with customer signature, along with following documents:
1. Photograph of failed component with Chassis/Engine number written with paint of Tractor thru courier/ e-mail.
needs to keep an acceptance letter duly signed by buyer in their records for 6 months to be cross checked by ITL randomly for audit purpose
·
Distributor must provide the Installation certificate copy with in 30 days from the date the tractor is delivered to customer, for reference of ITL during warranty settlement. The claim of tractor for which installation certificate is not submitted, warranty claim shall not be settled.
(D) - STORAGE OF DEFECTIVE PARTS: -
79
80
Operator Manual
All failed parts pertaining to warranty replacement are property of ITL & must be retained with distributor at least for 90 days from date of submission of warranty claims with proper tagging & packing for further Inspection/investigation by ITL
Engineer. These can be called back to ITL works if necessary for investigation at ITL expense.
(E) - SETTLEMENT OF WARRANTY CLAIM: -
Claim will be settled with in 30 days from date of submission of warranty claim as per ITL warranty policy by our warranty division and reimbursement of parts value as per latest prices (applicable import price at the time of repair of tractor) +
10% as freight component will be credited in Distributor account within 45 days of submission of warranty claim.
Address for submission of warranty claims: -
To,
Exports Department
INTERNATIONAL TRACTORS LTD,
Village- Chak Gujaran,
P.O.- Piplanwala-146022.
Jalandhar Road,
HOSHIARPUR (Punjab) INDIA.
Tel No +91-1882-302525 / 526
E- Mail [email protected]
Operator Manual
PROBLEM
Engine not starting
Engine not run in proper way
More oil consumption
Engine not giving maximum power
Engine abnormal noise
Oil pressure gauge shows warning
Engine Over
Heating
10. TROUBLE SHOOTING
REMEDY POSSIBLE CAUSE
ENGINE
Wrong way of starting engine
No fuel
Air trapped in fuel system
Checking of fuel system
Fuel injector faulty
Pull to lever knob in pulling condition
Fuel filter choke
Fuel filter choke
Low quality of oil
Choking of fuel system
Fuel injectors faulty
Oil level is more than maximum level
Oil quality is not good
Leakage of oil
Heavy load on engine
Air cleaner dirty
Fuel filter choke
Engine overheating
Engine operating temperature is less
Valve clearance not proper
Throttle system not working properly
Oil level less
Oil pressure less
Engine is overheated
Improper tappet setting
Oil level is less
Oil quality is not good
Oil pump not working
Radiator cap faulty
Choked radiator fins
Engine gets overload
Oil level is less
Coolant level is less
Slippage of fan belt
Thermostat faulty
Choking of cooling system
Water temp. Gauge not working
Use proper way of starting
Check oil level
Bleed the fuel system
Contact your dealer
Replace
Return it to its proper position
Replace filters
Replace filters
Drain diesel from tank and fill clean diesel
Check fuel system
Replace fuel injector
Keep oil level up to mark
Use genuine oil
Check and repair
Decrease load or shift in low gear
Clean air cleaner
Replace filter
Check cooling system
Check thermostat
Adjust through authorized dealer.
Check & repair through authorized dealer.
Top up
Check through authorized dealer
Check and find reason
Adjust through authorized dealer
Top up oil up to level
Use genuine engine oil
Check and repair through authorized dealer
Replace with new one
Clean it
Decrease load or shift to low gear
Top up to level
Check level and leakage of system and top up
Check belt tension
Replace
Clean the cooling system
Check through dealer and faulty replace
81
Operator Manual
PROBLEM
More
Fuel
Consumption
Excessive Heating
Of Oil
Linkage Goes
Down Slowly
Linkage Not Lift
Fully
Three Point Linkage
Not Respond To
Lifting While
Operating Hydraulic
Lever
Draft Control Fast
Hydraulic
System Not
Working
Properly
Draft Control Fast
Brakes Noisy
While Applying
Brakes Tractor
Goes In One Side
POSSIBLE CAUSE REMEDY
ENGINE
Air cleaner is dirty / choked
Overloading of engine
Improper valve clearance
Implement setting improper
Less engine temp
Fuel injection nozzle faulty
Clean air cleaner
Reduce load or shift to low gear
Check and adjust
Adjust it and take instrument from dealer for right option.
Check cooling system
Check and service through dealer
Improper inflation pressure
Oil level is high or less
Hydraulic filter element choked
Mechanical linkage may faulty
Bush tight
Response valve setting improper
Improper lift arm setting
Improper internal adjustment
HYDRAULIC
Check and adjust according to specified
Check and maintain proper level
Replace
Contact your authorized dealer
Contact your authorized dealer
Contact your authorized dealer
Contact your authorized dealer
Contact your authorized dealer
Linkage connection not joint properly
Heavy load on linkage
Contact your authorized dealer
Contact your authorized dealer
Draft / position control setting wrong
Implement not working well
Response valve setting very low
Oil level low
Hydraulic filter choked
Hydraulic system faulty
Hydraulic pump not working
Draft / position control setting wrong
BRAKES
Contact your authorized dealer
Make correct adjustment of implement.
Check valve by your dealer.
Check and top up
Replace filters
Check through authorized dealer
Contact your authorized dealer
Contact your authorized dealer and check system
Wrong adjustment of brakes Check
Both brakes are not set properly Adjust
82
Operator Manual
PROBLEM
Brakes Works
When Fully Pressed
POSSIBLE CAUSE
Wrong adjustment of brake pedal
REMEDY
Check and Adjust.
Electrical
System Not Working.
Starter Motor
Not Working.
Battery Not
Charging
ELECTRICAL
Battery terminal loose or rusting of terminal
Less specific gravity
Battery terminal loose
Battery discharged fully
Faulty starter motor
Loose or rusted terminals
Belt loose
Faulty battery
Clean and tight the terminals
Replace or fill electrolyte up to level
Tightened
Recharge or replace battery
For repair contact your dealer
Clean and tight terminal
Check belt tension
Replace
83
S.No.
1.
2.
3.
AREA
ENGINE
MAKE
MODEL:
TYPE
CYLINDERS
DISPLACEMENT (CC)
BORE/STROKE
MAXIMUM POWER Kw (Hp)
RATED SPEED
IDLE SPEED
MAX NO LOAD SPEED
MAX TORQUE SPEED
COOLING SYSTEM
FUEL INJECTION SYSTEM
AIR CLEANER
SILENCER
EMISSION COMPLIANCE
CLUTCH
TYPE
DISC FACING
DISC SIZE
TRANSMISSION
TYPE
REDUCTION TYPE
NO OF SPEEDS
SPEEDS AT RATED ENGINE
SPEED WITH 13.60X28 REAR
TYRES & GEAR RATIO
FORWARD
84
4.
REVERSE
POWER TAKE OFF
TYPE
MAX PTO POWER (KW/HP)
Operator Manual
11. SPECIFICATION
MAIN TECHNICAL DATA
SOLIS 50 2WD (Mech/Power Stg.) SOLIS 50 4WD
SONALIKA
3102EL
4 STROKE, DIRECT INJECTION,NA
3
2893 CC
102/118 MM
35.0 (46.91)
2100 RPM
750(+/-50) RPM
2300(-50) RPM
1200(+/-100)RPM
WATER COOLED
DIRECT INLINE
DRY AIR CLEANER WITH CLOGGING SENSOR
DOWN DRAFT/ UPDRAFT UNDER HOOD MUFFLER
TO MEETS CURRENT LEGISLATION OF EUROPEAN UNION STAGE III A
GEAR
DUAL CLUTCH
CERAMIC FOR DC
DUAL 280
-
CONSTANT MESH
BULL PINION
8+2
SPEED (Km/hr)
LOW-1
LOW-2
LOW-3
LOW-4
HIGH-1
HIGH-2
HIGH-3
HIGH-4
LOW
HIGH
1.77
2.58
4.34
7.26
7.56
10.99
18.49
30.92
2.27
9.68
TYPE I
30.52/40.91
Operator Manual
S.No.
5.
6.
7.
8.
9.
10.
11.
12.
13.
AREA
MAIN TECHNICAL DATA
SOLIS 50 2WD (Mech/Power Stg.) SOLIS 50 4WD
HYDRAULICS
PUMP CAPACITY
LIFT TYPE
LIFT CAPACITY (KG)
AUXILTARY HYDRAULIC
23.1 LIT/MIN FOR HYD AT RATED ENGINE RPM
POSITION AND AUTOMATIC MIX CONTROL
1200 AT THE ENDS OF LOWER LINK 1600
HYDRAULIC TRAILER BRAKES
2 DA/ CONVERTIBLE TO SA
THREE POINT LINKAGE
TYPE
STABILIZERS
STEERING
TYPE
STEERING WHEEL DIA (MM)
TURNING RADIUS
WITH BRAKES (M)
WITHOUT BRAKES (M)
BRAKES
SERVICE BRAKE
TYPE
OPERATION
PARKING BRAKE
TYPE
OPERATION
BODY & ERGONOMICS
PEDALS
GEAR SHIFT LEVERS
DRIVER SEAT
ELECTRICALS
TYPE
BATTERY
ALTERNATOR
STARTER MOTOR
HEAD LAMPS
PLOUGH LAMP
GAUGES
3.64
CAT 2
ADJUSTABLE STAY BAR
MECHANICAL / POWER STG.
434
2.95
OIB (STD)
MECHANICALLY OPERATED
MECHANICAL TYPE
HAND OPERATED
POWER STG.
4.72
CLUTCH AND BRAKE PEDAL FOOT OPERATED
SIDE SHIFTER
E-MARKED ADJUSTABLE TYPE
12 V
12V, 88Ah
12V, 36 Kw
12V, 2.7 KW
HIGH 60W / LOW 55W
35W
CLUSTER WITH ELECTRICAL HOUR METER/RPMMETER, ELECTRICAL
OIL PRESSURE GAUGE, VOLTMETER, ELECTRICAL TEMP GAUGE,
FUEL GAUGE, INDICATOR SWITCH FOR HIGH BEAM ETC.
FRONT AXLE
TYPE
MAX PERMISSIBLE LOAD (KG)
WHEELS & TYRES
FRONT
REAR
INFLATION PRESSURE OF TYRES
IN kPa
FRONT ( kPa)
REAR ( kPa)
ADJUSTABLE TYPE FIXED TYPE
1350 2080
6.00 X 16 9.50x20
13.6 X 28
250
150
85
Operator Manual
S.No.
14.
15.
16.
AREA
MAIN TECHNICAL DATA
SOLIS 50 2WD (Mech/Power Stg.)
SOLIS 50 4WD
HEIGHTS(Kg) AND DIMENSIONS
IN mm
OVERALL LENGTH
(WITH LINKAGE)
OVERALL WIDTH OF STANDARD
TRACTOR
GROUND CLEARANCE
HEIGHTS MM
AT REAR VIEW MIRROR
(WITH DOWN DRAFT SILENCER)
3820 3780
1790 1800
441 330
1840 1860
WITH UP DRAFT SILENCER
WHEEL BASE
1.
2.
3.
4.
5.
6.
STD./MAX. FRONT TRACK (STD. TRACTOR)
STD./MAX. REAR TRACK (STD. TRACTOR)
WEIGHT
(WITHOUT BALLAST)
FRONT
REAR
TOTAL
RECOMMENDED MAX BALLAST
(BALLAST WEIGHTS ARE NOT A
PART OF STANDARD TRACTOR BUT
CAN BE ORDERED AS OPTIONAL)
CAPACITIES IN LITERS
FUEL TANK
ENGINE SUMP
AIR CLEANER
TRANSMISSION CUM
HYDRAULIC FLUID
STEERING
BARE RADIATOR CAPACITY
TOTAL COOLANT
RECOMMENDED IMPLEMENTS
2200 2340
1980 2175
1310
1420
1530
1420
830 990
1615 1680
2445 2670
258 Kg. 6No's OF 31 Kg ON REAR
SIDE & 72 Kg. ON FRONT SIDE
Front - 326 kg. cast iron 6 numbers of
31 kg. each, one no. of 72 kg.
Rear - 2 no. of 34 kg. each
55 HSD
8.2
DRY TYPE
60
0.6
4.5
10.5
CULTIVATOR 11 TYNE
HARROW 8X8
MB PLOUGH TWO BOTTOM
DISC PLOUGH TWO BOTTOM
* COMPANY RESERVE THE RIGHT TO CHANGE SPECIFICATIONS AND/OR FEATURES OF PRODUCTS
WITHOUT NOTICE AT ANY TIME
86
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
1st
First Service (Hours: 50-60) / (One Month)
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
1st
First Service (Hours: 50-60) / (One Month)
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
2nd
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Second Service (Hours : 250-260)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
2nd
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Second Service (Hours : 250-260)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
JOBS TO BE PERFORMED DURING 60 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 140 to 150 NM
JOBS TO BE PERFORMED DURING 60 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 140 to 150 NM
JOBS TO BE PERFORMED DURING 260 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension (10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil/Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 140 to 150 NM
JOBS TO BE PERFORMED DURING 260 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension (10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil/Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 140 to 150 NM
3rd
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Third Service (Hours: 500-510)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
3rd
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Third Service (Hours: 500-510)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
4th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Fourth Service (Hours : 750-760)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
4th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Fourth Service (Hours : 750-760)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
JOBS TO BE PERFORMED DURING 510 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 510 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 760 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Brake housing / lining.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 760 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Brake housing / lining.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
5th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Fifth Service (Hours: 1000-1010)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
5th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Fifth Service (Hours: 1000-1010)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
6th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Sixth Service (Hours : 1250-1260)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
6th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
Sixth Service (Hours : 1250-1260)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
JOBS TO BE PERFORMED DURING 1010 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Transmission oil
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension 10mm
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner, Oil/Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 1010 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Transmission oil
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension 10mm
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner, Oil/Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 1260 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 1260 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
7th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Seventh Service (Hours: 1500)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
7th
Date:
Dealer Code:
Model:
Chassis No.
Engine No.
HMR
International Tractors Limited
Jalandhar Rd. Hoshiarpur- (Pb). 146 001
Phones: +91-1882- 302220, 302221, 302223
Seventh Service (Hours: 1500)
I here by certify that the service has been carried out to my entire satisfaction as per company recommended schedule.
Owner / Operator signature ..............................................
Owner / Operator Name ...................................................
Dealer stamp & signature:.................................................
Payment towards all consumables (All lub. /oils, bulb, etc.) will be borne by customer
JOBS TO BE PERFORMED DURING 1500 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Brake housing / lining.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
JOBS TO BE PERFORMED DURING 1500 HOURS SERVICE
Tick Operations
Washing
Lubrication
Oil Change
Check
&
Top up
Check
& Adjust
Check
Clean
Change
Torquing
Check Points
Complete Tractor.
Lubricate all grease nipples.
(Sonalika Maxima)
Engine Oil.
Air cleaner oil.
Coolant Level.
Electrolyte level of battery.
Oil level in steering box.
Tappet clearance.
Brake & Clutch pedal free play.
Belt Tension(10mm)
Idle RPM/Max RPM.
Toe-In & Tyre pressure.
Functioning of oil & temp. gauge.
Air cleaner Oil /Air Filter
Tightness of all bolts & nuts.
FIP feed pump bowl.
Vent plugs & terminals of battery.
Air cleaner element Wet / Dry.
Brake housing / lining.
Fuel Cock strainer.
Water separator
Lubrication oil filter & hyd. oil filter.
Engine & Bell Hsg M12*1.75*40
/M10*1.5 70/40 Nm
Front axle bolts 150 to 180 NM
Operator Manual
13. SERVICE RECORD
CH. NO. ______________________________ENGINE NO. _____________________ MODEL: ___________________
S.
NO.
DATE/
HMR
DEALER
CODE
BRIEF JOB DESCRIPTION ACTION TAKEN DEALER
SIGN
95
Operator Manual
14. NOTES
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
.....................................................................................................................................................................................................
96
CUSTOMER FEEDBACK CARD
1.
4.
5.
2.
3.
6.
Customer Name : ....................................................................................................................................................
Address : .................................................................................................................................................................
................................................................................................................. Phone (S)...............................................
Chassis No. ............................................... Engine No. ............................................... Model : .............................
Delivery Dealer Name .............................................................................................................................................
Delivery Dealer Code .................................................................. Delivery Date.....................................................
S.No.
ANY PROBLEMS FACED WITH THE TRACTOR
Rectified
(Yes/No)
l l l l
2. EXPERIENCE WHILE TAKING DELIVERY FROM
SHOW ROOM
GOOD FAIR POOR
Hospitality
Clear explanation by
Dealer's Staff on operation, features and maintenance of the
Tractor
Cleanliness of Tractor at delivery
YES NO
Was there any undue delay in handing over your Tractor on the day of delivery
Suggestion if Any :
l l
3. EXPERIENCE IN WORKSHOP
Name of Workshop : __________________________
City ________________________________________
GOOD FAIR POOR
Hospitality
Quality of repair/Service
YES NO
l l
Tractor delivered at promised time
Was post service follow up done
E ER H UT N C PE O TO
INLAND LETTER CARD
SONALIKA INTERNATIONAL TRACTORS LIMITED
Works : Village Chak Gujran, P.O. Piplanwala,
Jalandhar Road, Hoshiarpur, PUNJAB (INDIA)
Phone : +91 1882 302-525/526 www.sonalika.com
(Do not write or print below this line)____________ PIN
1 4 6 0 2 2
SECOND FOLD
NO ENCLOSURES ALLOWED
WRITE PIN CODE IN ADDRESS
SENDER'S NAME AND ADDRESS
PIN
FIRST FOLD
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Powerful engine for exceptional performance
- Advanced hydraulics for precise implement control
- User-friendly controls for effortless operation
- Rugged construction for durability and longevity
- Versatile design for a wide range of farming applications
- Comfortable operator environment for extended work sessions
Related manuals
Frequently Answers and Questions
What is the recommended load carrying capacity per tyre?
How do I adjust the track width?
What is the procedure to open the top hood?
How do I check the wheel nut bolts?
advertisement